Lathe Machine: The Engine Lathe

OBJECTIVE
After completing this unit, you should be able to:

• Identify the most important parts of the Lathe and their functions.
• Understand the Lathe safety rules.
• Describe setup a cutting tool for machining.
• Describe mount workpiece in the lathe.
• Explain how to install cutting tool.
• Describe the positioning the tool.
• Describe how to centering the workpiece and tailstock center.

Description
The lathe is a very versatile and important machine to know how to operate. This machine rotates a cylindrical object
against a tool that the individual controls. The lathe is the forerunner of all machine tools. The work is held and
rotated on its axis while the cutting tool is advanced along the line of a desired cut. The lathe is one of the most
versatile machine tools used in industry. With suitable attachments, the lather may be used for turning, tapering,
form turning, screw cutting, facing, dulling, boring, spinning, grinding, polishing operation. Cutting operations are
performed with a cutting tool fed either parallel or at right angles to the axis of the work. The cutting tool may also
be fed at an
angle, relative to
the axis of the
work, for
machining taper
and angles. On a
lathe, the
tailstock does
not rotate.
Instead, the
spindle that
holds the stock
rotates. Collets,
centers, three
jaw chucks, and
other work-
holding
attachments can
all be held in
spindle. The
tailstock can
hold tools for
drilling,
threading,
reaming, or
cutting tapers. Additionally, it can support the end of the workpiece using a center and can be adjusted to adapt to
different workpiece lengths.

Figure 1. Parts of a lathe

1. Power On/Off
2. Spindle Forward/Reverse (flip handle up or down)
 3. Carriage Handwheel 4. Cross Feed Handwheel
4. Compound Feed Handwheel
5. Carriage/Cross Feed Engage
6. Threading Half Nut
7. Threading Dial
8. Spindle Speed
9. Brake
10. Spindle High/Low Range
11. Thread/Feed Reverse (push in/pull out)
12. Feed Ranges (A, B, C)
13. Feed Ranges (R, S, T)
14. Feed Ranges (V, W, X, Y, Z) – V and Z are settings for threading
15. Gear Box
16. Gear Box Low/High
17. Tailstock
18. Tool Post
19. Toolholder
20. Three – Jaw Chuck
21. DRO (Digital Read Out) Threading/Feed Selector (see item15)

Lathe Safety
As always we should be aware of safety requirements and attempt to observe safety rules in order to eliminate
serious injury to ourselves or others.

Wear glasses, short sleeves, no tie, no rings, no trying to stop the work by hand. Stop the machine before trying to
check the work. Don’t know how it works? –“Don’t run it.” Don’t use rags when the machine is running.

1. Remove the chuck key from the chuck immediately after use. Do not turn the lathe on if the chuck is still in
the chuck key.
2. Turn the chuck or faceplate through by hand unless there are binding or clearance issues.
3. It is important that the chuck or faceplate is securely tightened onto the lathe’s spindle.
4. Move the tool bit to a safe distance from the chuck, collet, or face plate when inserting or removing your
part.
5. Place the tool post holder to the left of the compound slide. This will ensure that the compound slide will not
run into the spindle or chuck attachments.
6. When installing and removing chucks, face plates, and centers, always be sure all mating surfaces are clean
and free from burrs.
7. Make sure the tool bit is sharp and has correct clearance angles.
8. Clamp the tool bit as short as possible in the tool holder to prevent it from vibrating or breaking.
9. Evenly apply and maintain cutting fluids. This will prevent morphing.
10. Do not run a threaded spindle in reverse.
11. Never run the machine faster than the recommended speed for the specific material.
12. If a chuck or faceplate is jammed on the spindle nose, contact an instructor to remove it.
13. If any filing is done on work revolving in the lathe, file left handed to prevent slipping into the chuck.
14. Always stop the machine before taking measurements.
15. Stop the machine when removing long stringy chips. Remove them with a pair of pliers.
16. Make sure that the tailstock is locked in place and that the proper adjustments are made if the work is being
turned between centers.
17. When turning between centers, avoid cutting completely through the piece.
18. Do not use rags while the machine is running.
19. Remove tools from the tool post and tailstock before cleaning.
20. Do not use compressed air to clean the lathe.
 21. Use care when cleaning the lathe. The cutting tools are sharp, the chips are sharp, and the workpiece may be
sharp.
22. Make sure the machine is turned off and clean before leaving the workspace. Always remove the chuck
wrench after use, avoid horseplay, keep floor area clean. Use care when cleaning the lathe, the cutting tools
are sharp, the chips are sharp, and the workpiece may be sharp.

Here are some questions which are important when running a lathe:

The lathe is a machine tool used principally for shaping pieces of metal (and sometimes wood or other materials) by
causing the workpiece to be held and rotated by the lathe while a tool bit is advanced into the work causing the
cutting action. The basic lathe that was designed to cut cylindrical metal stock has been developed further to
produce screw threads, tapered work, drilled holes, knurled surfaces, and crankshafts. Modern lathes offer a variety
of rotating speeds and a means to manually and automatically move the cutting tool into the workpiece. Machinists
and maintenance shop personnel must be thoroughly familiar with the lathe and its operations to accomplish the
repair and fabrication of needed parts.

TYPES OF LATHES

Lathes can be divided into three types for easy identification: engine lathe, turret lathe, and special purpose lathes.
Some smaller ones are bench mounted and semi-portable. The larger lathes are floor mounted and may require
special transportation if they must be moved. Field and maintenance shops generally use a lathe that can be adapted
to many operations and that is not too large to be moved from one work site to another. The engine lathe (Figure 7-
1) is ideally suited for this purpose. A trained operator can accomplish more machining jobs with the engine lathe
than with any other machine tool. Turret lathes and special purpose lathes are usually used in production or job
shops for mass production or specialized parts, while basic engine lathes are usually used for any type of lathe work.
Further reference to lathes in this chapter will be about the various engine lathes.

ENGINE LATHES

Sizes

The size of an engine lathe is determined by the largest piece of stock that can be machined. Before machining a
workpiece, the following measurements must be considered: the diameter of the work that will swing over the bed
and the length between lathe centers (Figure 7-1).

Categories
Slight differences in the various engine lathes make it easy to group them into three categories: lightweight bench
engine lathes, precision tool room lathes, and gap lathes, which are also known as extension-type lathes. These lathe
categories are shown in Figure 7-2 Different manufacturers may use different lathe categories.

Lightweight

Lightweight bench engine lathes are generally small lathes with a swing of 10 inches or less, mounted to a bench or
table top. These lathes can accomplish most machining jobs, but may be limited due to the size of the material that
can be turned.

Precision

Precision tool room lathes are also known as standard manufacturing lathes and are used for all lathe operations,
such as turning, boring, drilling, reaming, producing screw threads, taper turning, knurling, and radius forming, and
can be adapted for special milling operations with the appropriate fixture. This type of lathe can handle workpieces
up to 25 inches in diameter and up to 200 inches long. However, the general size is about a 15-inch swing with 36 to
48 inches between centers. Many tool room lathes are used for special tool and die production due to the high
accuracy of the machine.

GAP OR EXTENSION-TYPE LATHES

Gap or extension-type lathes are similar to toolroom lathes except that gap lathes can be adjusted to machine larger
diameter and longer workpieces The operator can increase the swing by moving the bed a distance from the
headstock, which is usually one or two feet. By sliding the bed away from the headstock, the gap lathe can be used to
turn very long workpieces between centers.

LATHE COMPONENTS

Engine lathes all have the same general functional parts, even though the specific location or shape of a certain part
may differ from one manufacturer The bed is the foundation of the working parts of the lathe to another (Figure 7-3).
The main feature of its construction are the ways which are formed on its upper surface and run the full length of the
bed.

Ways provide the means for holding the tailstock and carriage, which slide along the ways, in alignment with the
permanently attached headstock

The headstock is located on the operator's left end of the lathe bed. It contains the main spindle and oil reservoir and
the gearing mechanism for obtaining various spindle speeds and for transmitting power to the feeding and threading
mechanism. The headstock mechanism is driven by an electric motor connected either to a belt or pulley system or
to a geared system. The main spindle is mounted on bearings in the headstock and is hardened and specially ground
to fit different lathe holding devices. The spindle has a hole through its entire length to accommodate long
workpieces. The hole in the nose of the spindle usually has a standard Morse taper which varies with the size of the
lathe. Centers, collets, drill chucks, tapered shank drills and reamers may be inserted into the spindle. Chucks, drive
plates, and faceplates may be screwed onto the spindle or clamped onto the spindle nose.

The tailstock is located on the opposite end of the lathe from the headstock. It supports one end of the work when
machining between centers, supports long pieces held in the chuck, and holds various forms of cutting tools, such as
drills, reamers, and taps. The tailstock is mounted on the ways and is designed to be clamped at any point along the
ways. It has a sliding spindle that is operated by a hand wheel and clamped in position by means of a spindle clamp.
The tailstock may be adjusted laterally (toward or away from the operator) by adjusting screws. It should be
unclamped from the ways before any lateral adjustments are made, as this will allow the tailstock to be moved freely
and prevent damage to the lateral adjustment screws.

The carriage includes the apron, saddle, compound rest, cross slide, tool post, and the cutting tool. It sits across the
lathe ways and in front of the lathe bed. The function of the carriage is to carry and move the cutting tool. It can be
moved by hand or by power and can be clamped into position with a locking nut. The saddle carries the cross slide
and the compound rest. The cross slide is mounted on the dovetail ways on the top of the saddle and is moved back
and forth at 90� to the axis of the lathe by the cross slide lead screw. The lead screw can be hand or power
activated. A feed reversing lever, located on the carriage or headstock, can be used to cause the carriage and the
cross slide to reverse the direction of travel. The compound rest is mounted on the cross slide and can be swiveled
and clamped at any angle in a horizontal plane. The compound rest is used extensively in cutting steep tapers and
angles for lathe centers. The cutting tool and tool holder are secured in the tool post which is mounted directly to the
compound rest. The apron contains the gears and feed clutches which transmit motion from the feed rod or lead
screw to the carriage and cross slide.

CARE AND MAINTENANCE OF LATHES

Lathes are highly accurate machine tools designed to operate around the clock if properly operated and maintained.
Lathes must be lubricated and checked for adjustment before operation. Improper lubrication or loose nuts and bolts
can cause excessive wear and dangerous operating conditions.

The lathe ways are precision ground surfaces and must not be used as tables for other tools and should be kept clean
of grit and dirt. The lead screw and gears should be checked frequently for any metal chips that could be lodged in
the gearing mechanisms. Check each lathe prior to operation for any missing parts or broken shear pins. Refer to the
operator's instructions before attempting to lift any lathe. Newly installed lathes or lathes that are transported in
mobile vehicles should be properly leveled before any operation to prevent vibration and wobble. Any lathes that are
transported out of a normal shop environment should be protected from dust, excessive heat, and very cold
conditions. Change the lubricant frequently if working in dusty conditions. In hot working areas, use care to avoid
overheating the motor or damaging any seals. Operate the lathe at slower speeds than normal when working in cold
environments.

SAFETY

All lathe operators must be constantly aware of the safety hazards that are associated with using the lathe and must
know all safety precautions to avoid accidents and injuries. Carelessness and ignorance are two great menaces to
personal safety. Other hazards can be mechanically related to working with the lathe, such as proper machine
maintenance and setup. Some important safety precautions to follow when using lathes are:

 Correct dress is important, remove rings and watches, roll sleeves above elbows.
 Always stop the lathe before making adjustments.
 Do not change spindle speeds until the lathe comes to a complete stop.
 Handle sharp cutters, centers, and drills with care.
 Remove chuck keys and wrenches before operating
 Always wear protective eye protection.
 Handle heavy chucks with care and protect the lathe ways with a block of wood when installing a chuck.
 Know where the emergency stop is before operating the lathe.
 Use pliers or a brush to remove chips and swarf, never your hands.
 Never lean on the lathe.
 Never lay tools directly on the lathe ways. If a separate table is not available, use a wide board with a cleat on
each side to lay on the ways.
 Keep tools overhang as short as possible.
 Never attempt to measure work while it is turning.
 Never file lathe work unless the file has a handle.
 File left-handed if possible.
 Protect the lathe ways when grinding or filing.
 Use two hands when sanding the workpiece. Do not wrap sand paper or emory cloth around the workpiece.

TOOLS AND EQUIPMENT

GENERAL PURPOSE CUTTING TOOLS

The lathe cutting tool or tool bit must be made of the correct material and ground to the correct angles to machine a
workpiece efficiently. The most common tool bit is the general all-purpose bit made of high-speed steel. These tool
bits are generally inexpensive, easy to grind on a bench or pedestal grinder, take lots of abuse and wear, and are
strong enough for all-around repair and fabrication. High-speed steel tool bits can handle the high heat that is
generated during cutting and are not changed after cooling. These tool bits are used for turning, facing, boring and
other lathe operations. Tool bits made from special materials such as carbides, ceramics, diamonds, cast alloys are
able to machine workpieces at very high speeds but are brittle and expensive for normal lathe work. High-speed steel
tool bits are available in many shapes and sizes to accommodate any lathe operation.

SINGLE POINT TOOL BITS

Single point tool bits can be one end of a high-speed steel tool bit or one edge of a carbide or ceramic cutting tool or
insert. Basically, a single point cutter bit is a tool that has only one cutting action proceeding at a time. A machinist or
machine operator should know the various terms applied to the single point tool bit to properly identify and grind
different tool bits (Figure 7-4).

 The shank is the main body of the tool bit.

 The nose is the part of the tool bit which is shaped to a point and forms the corner between the side cutting
edge and the end cutting edge. The nose radius is the rounded end of the tool bit.

 The face is the top surface of the tool bit upon which the chips slide as they separate from the work piece.

 The side or flank of the tool bit is the surface just below and adjacent to the cutting edge.

 The cutting edge is the part of the tool bit that actually cuts into the workpiece, located behind the nose and
adjacent to the side and face.

 The base is the bottom surface of the tool bit, which usually is ground flat during tool bit manufacturing.

 The end of the tool bit is the near-vertical surface which, with the side of the bit, forms the profile of the bit.
The end is the trailing surface of the tool bit when cutting.

 The heel is the portion of the tool bit base immediately below and supporting the face.

Angles of Tool Bits

The successful operation of the lathe and the quality of work that may be achieved depend largely on the angles that
form the cutting edge of the tool bit (Figure 7-4). Most tools are hand ground to the desired shape on a bench or
pedestal grinder. The cutting tool geometry for the rake and relief angles must be properly ground, but the overall
shape of the tool bit is determined by the preference of the machinist or machine operator. Lathe tool bit shapes can
be pointed, rounded, squared off, or irregular in shape and still cut quite well as long as the tool bit angles are
properly ground for the type of material being machined. The angles are the side and back rake angles, the side and
end cutting edge angles, and the side and end relief angles. Other angles to be considered are the radius on the end
of the tool bit and the angle of the tool holder. After knowing how the angles affect the cutting action, some
recommended cutting tool shapes can be considered.

Rake angle pertains to the top surface of the tool bit. There are two types of rake angles, the side and back rake
angles (Figure 7-4). The rake angle can be positive, negative, or have no rake angle at all. The tool holder can have an
angle, known as the tool holder angle, which averages about 15�, depending on the model of tool holder selected.
The tool holder angle combines with the back rake angle to provide clearance for the heel of the tool bit from the
workpiece and to facilitate chip removal. The side rake angle is measured back from the cutting edge and can be a
positive rake angle or have no rake at all.
Rake angles cannot be too great or the cutting edge will lose strength to support the cutting action. The side rake
angle determines the type and size of chip produced during the cutting action and the direction that the chip travels
when leaving the cutting tool. Chip breakers can be included in the side rake angle to ensure that the chips break up
and do not become a safety hazard.

Side and relief angles, or clearance angles, are the angles formed behind and beneath the cutting edge that provide
clearance or relief to the cutting action of the tool. There are two types of relief angles, side relief and end relief. Side
relief is the angle ground into the tool bit, under the side of the cutting edge, to provide clearance in the direction of
tool bit travel. End relief is the angle ground into the tool bit to provide front clearance to keep the tool bit heel from
rubbing. The end relief angle is supplemented by the tool holder angle and makes up the effective relief angle for the
end of the tool bit.

Side and cutting edge angles are the angles formed by the cutting edge with the end of the tool bit (the end cutting
edge angle), or with the side of the tool bit (the side cutting edge angle). The end cutting edge angle permits the
nose of the tool bit to make contact with the work and aids in feeding the tool bit into the work. The side cutting
edge angle reduces the pressure on the tool bit as it begins to cut. The side rake angle and the side relief angle
combine to form the wedge angle (or lip angle) of the tool bit that provides for the cutting action (Figure 7-4).

A radius ground onto the nose of the tool bit can help strengthen the tool bit and provide for a smooth cutting
action.

Shapes of Tool Bits

The overall shape of the lathe tool bits can be rounded, squared, or another shape as long as the proper angles are
included. Tool bits are identified by the function they perform, such as turning or facing. They can also be identified
as roughing tools or finishing tools. Generally, a roughing tool has a radius ground onto the nose of the tool bit that is
smaller than the radius for a finishing or general-purpose tool bit. Experienced machinists have found the following
shapes to be useful for different lathe operations.

A right-hand turning tool bit is shaped to be fed from right to left. The cutting edge is on the left side of the tool bit
and the face slopes down away from the cutting edge. The left side and end of the tool bit are ground with sufficient
clearance to permit the cutting edge to bear upon the workpiece without the heel rubbing on the work. The right-
hand turning tool bit is ideal for taking light roughing cuts as well as general all-around machining.

A left-hand turning tool bit is the opposite of the right-hand turning tool bit, designed to cut when fed from left to
right. This tool bit is used mainly for machining close in to a right shoulder.

The round-nose turning tool bit is very versatile and can be used to turn in either direction for roughing and finishing
cuts. No side rake angle is ground into the top face when used to cut in either direction, but a small back rake angle
may be needed for chip removal. The nose radius is usually ground in the shape of a half-circle with a diameter of
about 1/32 inch.

The right-hand facing tool bit is intended for facing on right-hand side shoulders and the right end of a workpiece.
The cutting edge is on the left-hand side of the bit, and the nose is ground very sharp for machining into a square
corner. The direction of feed for this tool bit should be away from the center axis of the work, not going into the
center axis.

A left-hand facing tool bit is the opposite of the right-hand facing tool bit and is intend to machine and face the left
sides of shoulders.
The parting tool bit, Figure 7-6, is also known as the cutoff tool bit. This tool bit has the principal cutting edge at the
squared end of the bit that is advanced at a right angle into the workpiece. Both sides should have sufficient
clearance to prevent binding and should be ground slightly narrower at the back than at the cutting edge. Besides
being used for parting operations, this tool bit can be used to machine square corners and grooves.
Thread-cutting tool bits, Figure 7-7, are ground to cut the type and style of threads desired. Side and front clearances
must be ground, plus the special point shape for the type of thread desired. Thread-cutting tool bits can be ground
for standard 60� thread forms or for square, Acme, or special threads. Thread-cutting forms are discussed in greater
detail later in this chapter.

SPECIAL TYPES OF LATHE CUTTING TOOLS

Besides the common shaped tool bits, special lathe operations and heavy production work require special types of
cutting tools. Some of the more common of these tools are listed below.

Tungsten carbide, tantalum carbide, titanium carbide, ceramic, oxide, and diamond-tipped tool bits (Figure 7-8). and
cutting tool inserts are commonly used in high-speed production work when heavy cuts are necessary and where
exceptionally hard and tough materials are encountered. Standard shapes for tipped tool bits are similar to high-
speed steel-cutting tool shapes. Carbide and ceramic inserts can be square, triangular, round, or other shapes. The
inserts are designed to be indexed or rotated as each cutting edge gets dull and then discarded. Cutting tool inserts
are not intended for reuse after sharpening.

Specially formed thread cutter mounted in a thread cutter holder (Figure 7-9). This tool is designed for production
high-speed thread cutting operations. The special design of the cutter allows for sharp and strong cutting edges
which need only to be resharpened occasionally by grinding the face. The cutter mounts into a special tool holder
that mounts to the lathe tool post.
The common knurling tool, Figure 7-10, consists of two cylindrical cutters, called knurls, which rotate in a specially
designed tool holder. The knurls contain teeth which are rolled against the surface of the workpiece to form
depressed patterns on the workpiece. The common knurling tool accepts different pairs of knurls, each having a
different pattern or pitch. The diamond pattern is most widely used and comes in three pitches: 14, 21, or 33. These
pitches produce coarse, medium, and fine knurled patterns.

Boring tool bits, Figure 7-11, are ground similar to left-hand turning tool bits and thread-cutting tool bits, but with
more end clearance angle to prevent the heel of the tool bit from rubbing against the surface of the bored hole. The
boring tool bit is usually clamped to a boring tool holder, but it can be a one-piece unit . The boring tool bit and tool
holder clamp into the lathe tool post.
There is no set procedure to grinding lathe tool bit angles and shapes, but there are general guidelines that should be
followed. Do not attempt to use the bench or pedestal grinder without becoming fully educated as to its safety,
operation, and capabilities. In order to
effectively grind a tool bit, the grinding
wheel must have a true and clean face
and be of the appropriate material for
the cutting tool to be ground. Carbide
tool bits must be ground on a silicon
carbide grinding wheel to remove the
very hard metal.

High-speed steel tool bits are the only

tool bits that can effectively be ground
on the bench or pedestal grinder when
equipped with the aluminum oxide
grinding wheel which is standard for
most field and maintenance shops.
Before grinding, shaping, or sharpening
a high-speed steel tool bit, inspect the
entire grinder for a safe setup and
adjust the tool rests and guards as
needed for tool bit grinding (Figure 7-
12).
Set the tool rest 1/8 inch or less from the wheel, and adjust the spark arrestor 1/4 inch or less. Each grinder is usually
equipped with a coarse-grained wheel for rough grinding and a fine-grained wheel for fine and finish grinding. Dress
the face of the grinding wheels as needed to keep a smooth, flat grinding surface for the tool bit. When grinding the
side and back rake angles, ensure the grinding wheel has a sharp corner for shaping the angle. Dip the tool bit in
water occasionally while grinding to keep the tool bit cool enough to handle and to avoid changing the property of
the metal by overheating. Frequently inspect the tool bit angles with a protractor or special grinding gage. Grind the
tool bit to the recommended angles in the reference for tool bit geometry (Machinist Table 7-l ). After grinding to the
finished shape, the tool bit should be honed lightly on an oilstone to remove any burrs or irregular high spots. The
smoother the finish on the cutting tool, the smoother the finish on the work. Figure 7-13 shows the steps involved in
grinding a round nose tool bit to be used for turning in either direction. As a safety note, never use the side of the
grinding wheel to grind a tool bit, as this could weaken the bonding of the wheel and cause it to crack and explode.

TOOL HOLDERS AND TOOL POSTS

Lathe tool holders are designed to securely and rigidly hold the tool bit at a fixed angle for properly machining a
workpiece (Figure 7-14). Tool holders are designed to work in conjunction with various lathe tool posts, onto which
the tool holders are mounted. Tool holders for high speed steel tool bits come in various types for different uses.
These tool holders are designed to be used with the standard round tool post that usually is supplied with each
engine lathe (Figure 7-15 ). This tool post consists of the post, screw, washer, collar, and rocker, and fits into the T-slot
of the compound rest.
Standard tool holders for high-speed steel cutting tools have a square slot made to fit a standard size tool bit shank.
Tool bit shanks can be 1/4-inch, 5/16-inch, 3/8-inch, and greater, with all the various sizes being manufactured for all
the different lathe manufacturer's tool holder models. Some standard tool holders for steel tool bits are the straight
tool holder, right and left offset tool holder, and the zero rake tool holder designed for special carbide tool bits. Other
tool holders to fit the standard round tool post include straight, left, and right parting tool holders, knurling tool
holders, boring bar tool holders, and specially formed thread cutting tool holders.

The turret tool post (Figure 7-16 ) is a swiveling block that can hold many different tool bits or tool holders. Each
cutting tool can quickly be swiveled into cutting position and clamped into place using a quick clamping handle. The
turret tool post is used mainly for high-speed production operations.
The heavy-duty or open-sided tool post (Figure 7-17) is used for holding a single carbide-tipped tool bit or tool
holder. It is used mainly for very heavy cuts that require a rigid tool holder.

The quick-change tool system (Figure 7-18) consists of a quick-change dovetail tool post with a complete set of
matching dovetailed tool holders that can be quickly changed as different lathe operations become necessary. This
system has a quick-release knob on the top of the tool post that allows tool changes in less than 5 seconds, which
makes this system valuable for production machine shops.

WORK HOLDING DEVICES

Many different devices, such as chucks, collets, faceplates, drive plates, mandrels, and lathe centers, are used to hold
and drive the work while it is being machined on a lathe. The size and type of work to be machined and the particular
operation that needs to be done will determine which work holding device is best for any particular job. Another
consideration is how much accuracy is needed for a job, since some work holding devices are more accurate than
others. Operational details for some of
the more common work holding devices
follow.

The universal scroll chuck, Figure 7-19,

usually has three jaws which move in
unison as an adjusting pinion is rotated.
The advantage of the universal scroll
chuck is its ease of operation in centering
work for concentric turning. This chuck is
not as accurate as the independent
chuck, but when in good condition it will
center work within 0.002 to 0.003 inches
of runout.

The jaws are moved simultaneously

within the chuck by a scroll or spiral-
threaded plate. The jaws are threaded to
the scroll and move an equal distance
inward or outward as the scroll is rotated
by the adjusting pinion. Since the jaws
are individually aligned on the scroll, the
jaws cannot usually be reversed. Some
manufactures supply two sets of jaws,
one for internal work and one for
external work. Other manufactures make
the jaws in two pieces so the outside, or
gripping surface may be reversed. which
can be interchanged.

The universal scroll chuck can be used to

hold and automatically center round or
hexagonal workpieces. Having only three
jaws, the chuck cannot be used
effectively to hold square, octagonal, or
irregular shapes.
The independent chuck, Figure 7-19, generally has four jaws which are adjusted individually on the chuck face by
means of adjusting screws. The chuck face is scribed with concentric circles which are used for rough alignment of
the jaws when chucking round workpieces. The final adjustment is made by turning the workpiece slowly by hand
and using a dial indicator to determine it's concentricity. The jaws are then readjusted as necessary to align the
workpiece within the desired tolerances.

The jaws of the independent chuck

may be used as illustrated or may
be reversed so that the steps face
in the opposite direction; thus
workpieces can be gripped either
externally or internally. The
independent chuck can be used to
hold square, round, octagonal, or
irregularly shaped workpieces in
either a concentric or eccentric
position due to the independent
operation of each jaw.

Because of its versatility and

capacity for fine adjustment, the
independent chuck is commonly
used for mounting odd-shaped
workpieces which must be held
with extreme accuracy.

A combination chuck combines the

features of the independent chuck
and the universal scroll chuck and
can have either three or four jaws.
The jaws can be moved in unison on a scroll for automatic centering or can be moved individually if desired by
separate adjusting screws.

The drill chuck, Figure 7-19, is a small universal chuck which can be used in either the headstock spindle or the
tailstock for holding straight-shank drills, reamers, taps, or small diameter workpieces. The drill chuck has three or
four hardened steel jaws which are
moved together or apart by adjusting a
tapered sleeve within which they are
contained. The drill chuck is capable of
centering tools and small-diameter
workpieces to within 0.002 or 0.003 inch
when firmly tightened.

The collet chuck is the most accurate

means of holding small workpieces in the
lathe. The collet chuck consists of a
spring machine collet (Figure 7-20) and a
collet attachment which secures and
regulates the collet on the headstock
spindle of the lathe.

THE COLLET CHUCK IS THE MOST

ACCURATE MEANS OF HOLDING SMALL
WORKPIECES IN THE LATHE
 The spring machine collet is a thin metal bushing
with an accurately machined bore and a tapered
exterior. The collet has three lengthwise slots to
permit its sides being sprung slightly inward to grip
the workpiece. To grip the workpiece accurately,
the collet must be no more than 0.005 inch larger
or smaller than the diameter of the piece to be
chucked. For this reason, spring machine collets
are available in increments of 1/64 inch. For
general purposes, the spring machine collets are
limited in capacity to 1 1/8 inch in diameter.

For general purposes, the spring machine collets

are limited in capacity to 1 1/8 inch in diameter.

The collet attachment consists of a collet sleeve, a

drawbar, and a handwheel or hand lever to move
the drawbar. The spring machine collet and collet
attachment together form the collet chuck. Figure
7-20 illustrates a typical collet chuck installation.
The collet sleeve is fitted to the right end of the headstock spindle. The drawbar passes through the headstock
spindle and is threaded to the spring machine collet. When the drawbar is rotated by means of the hand wheel, it
draws the collet into the tapered adapter, causing the collet to tighten on the workpiece. Spring machine collets are
available in different shapes to chuck square and hexagonal workpieces of small dimensions as well as round
workpieces.

The Jacob's spindle-nose collet chuck (Figure 7-21) is a special chuck is used for the Jacob's rubber flex collets. This
chuck combines the functions of the standard collet chuck and drawbar into one single compact unit. The chuck
housing has a handwheel on the outer diameter that turns to tighten or loosen the tapered spindle which holds the
rubber flex collets. Rubber flex collets are comprised of devices made of hardened steel jaws in a solid rubber
housing. These collets have a range of 1/8 inch per collet. The gripping power and accuracy remain constant
throughout the entire collet capacity. Jacob's rubber flex collets are designed for heavy duty turning and possess two
to four times the grip of the conventional split steel collet. The different sets of these collets are stored in steel boxes
designed for holding the collets. Collets are normally stored in steel boxes designed for holding the collets.

The step chuck, Figure 7-22, is a variation of the collet chuck, and it is intended for holding small round workpieces or
discs for special machining jobs. Step chucks are blank when new, and then are machined in the lathe for an exact fit
for the discs to be turned. The step chuck machine collet, which is split into three sections like the spring machine
collet, is threaded to the drawbar of the collet attachment.
The lathe tailstock chuck, Figure 7-22, is a device designed to support the ends of workpieces in the tailstock when a
lathe center cannot be used conveniently. The chuck has a taper arbor that fits into the lathe tailstock spindle. The
three bronze self-centering jaws of the chuck will accurately close upon workpieces between 1/4 and 1 inch in
diameter. The bronze jaws provide a good bearing surface for the workpiece. The jaws are adjusted to the diameter
of the workpiece and then locked in place.

A lathe faceplate, Figure 7-23, is a flat, round plate that threads to the headstock spindle of the lathe. The faceplate is
used for irregularly shaped workpieces that cannot be successfully held by chucks or mounted between centers. The
workpiece is either attached to the faceplate using angle plates or brackets or bolted directly to the plate. Radial T-
slots in the faceplate surface facilitate mounting workpieces. The faceplate is valuable for mounting workpieces in
which an eccentric hole or projection is to be machined. The number of applications of the faceplates depends upon
the ingenuity of the machinist. A small faceplate known as a driving faceplate is used to drive the lathe dog for
workpieces mounted between centers. The driving faceplate usually has fewer T-slots than the larger faceplates.
When the workpiece is supported between centers, a lathe dog is fastened to the workpiece and engaged in a slot of
the driving faceplate.

Lathe centers, are the most common devices for supporting workpieces in the lathe. Most lathe centers have a
tapered point with a 60� included angle to fit workpiece holes with the same angle. The workpiece is supported
between two centers, one in the headstock spindle and one in the tailstock spindle. Centers for lathe work have
standard tapered shanks that fit directly into the tailstock and into the headstock spindle using a center sleeve to
convert the larger bore of the spindle to the smaller tapered size of the lathe center. The centers are referred to as
live centers or dead centers. A live center revolves with the work and does not need to be lubricated and hardened. A
dead center does not revolve with the work and must be hardened and heavily lubricated when holding work. Live
and dead centers commonly come in matched sets, with the hardened dead center marked with a groove near the
conical end point.
The ball bearing live center is a special center mounted in a ball bearing housing that lets the center turn with the
work and eliminates the need for a heavily lubricated dead center. Ball bearing types of centers can have
interchangeable points which make this center a versatile tool in all lathe operations. Modern centers of this type can
be very accurate. Descriptions for some common lathe centers follow.

The male center or plain center is used in pairs for most general lathe turning operations. The point is ground to a
60� cone angle. When used in the headstock spindle where it revolves with the workpiece, it is commonly called a
live center. When used in the tailstock spindle where it remains stationary when the workpiece is turned, it is called a
dead center. Dead centers are always made of hardened steel and must be lubricated very often to prevent
overheating.

The half male center is a male center that has a portion of the 60� cone cut away. The half male center is used as a
dead center in the tailstock where facing is to be performed. The cutaway portion of the center faces the cutting tool
and provides the necessary clearance for the tool when facing the surface immediately around the drilled center in
the workpiece.

The V-center is used to support round workpieces at right angles to the lathe axis for special operations such as
drilling or reaming. The pipe center is similar to the male center but its cone is ground to a greater angle and is larger
in size. It is used for holding pipe and tubing in the lathe. The female center is conically bored at the tip and is used to
support workpieces that are pointed on the end. A self-driving lathe center is a center with serrated ground sides
that can grip the work while turning between centers without having to use lathe dogs.

A self driving center is a center that has grips installed on the outer edge of the center diameter that can be forced
into the work to hold and drive the work when turning between centers without using lathe dogs.

Lathe dogs are cast metal devices used to provide a firm connection between the headstock spindle and the
workpiece mounted between centers. This firm connection permits the workpiece to be driven at the same speed as
the spindle under the strain of cutting. Three common lathe dogs are illustrated in Figure 7-25. Lathe dogs may have
bent tails or straight tails. When bent-tail dogs are used, the tail fits into a slot of the driving faceplate. When straight-
tail dogs are used, the tail bears against a stud projecting from the faceplate. The bent-tail lathe dog with headless
setscrew is considered safer than the
dog with the square head screw
because the headless setscrew reduces
the danger of the dog catching in the
operator's clothing and causing an
accident. The bent-tail clamp lathe dog
is used primarily for rectangular
workpieces.

MANDRELS

A workpiece which cannot be held

between centers because its axis has
been drilled or bored, and which is not
suitable for holding in a chuck or
against a faceplate, is usually machined
on a mandrel. A mandrel is a tapered
axle pressed into the bore of the
workpiece to support it between
centers.

A mandrel should not be confused with

an arbor, which is a similar device but
used for holding tools rather than
workpieces. To prevent damage to the
work, the mandrel should always be
oiled before being forced into the hole.
When turning work on a mandrel, feed
toward the large end which should be
nearest the headstock of the lathe.
 A solid machine mandrel is generally
made from hardened steel and ground
to a slight taper of from 0.0005 to
0.0006 inch per inch. It has very
accurately countersunk centers at each
end for mounting between centers. The
ends of the mandrel are smaller than
the body and have machined flats for
the lathe dog to grip. The size of the
solid machine mandrel is always
stamped on the large end of the taper.
Since solid machine mandrels have a
very slight taper, they are limited to
workpieces with specific inside
diameters.

An expansion mandrel will accept

workpieces having a greater range of
sizes. The expansion mandrel is, in
effect, a chuck arranged so that the
grips can be forced outward against the interior of the hole in the workpiece.

LATHE ATTACHMENTS

The variety of work that can be performed on the lathe is

greatly increased by the use of various lathe attachments.
Some lathes come equipped with special attachments;
some attachments must be ordered separately. Some
common lathe attachments are the steady rest with
cathead, the follower rest, the tool post grinding machine,
the lathe micrometer stop, the lathe milling fixture, the
lathe coolant attachment, the lathe indexing fixture, and
the milling-grinding-drilling-slotting attachment (or Versa-
Mil). The lathe indexing fixture and Versa-Mil unit are
detailed in Chapter 9. Descriptions for the other lathe
attachments follows.

RESTS

Workpieces often need extra support, especially long, thin

workpieces that tend to spring away from the tool bit.
Three common supports or rests are the steady rest, the
cathead, and the follower rest (Figure 7-27).

Steady Rest

The steady rest, also called a center rest, is used to

support long workpieces for turning and boring
operations. It is also used for internal threading operations
where the workpiece projects a considerable distance
from the chuck or faceplate. The steady rest is clamped to
the lathe bed at the desired location and supports the
workpiece within three adjustable jaws. The workpiece
must be machined with a concentric bearing surface at the point where the steady rest is to be applied. The jaws
must be carefully adjusted for proper alignment and locked in position. The area of contact must be lubricated
frequently. The top section of the steady rest swings away from the bottom section to permit removal of the
workpiece without disturbing the jaw setting.

Cathead

When the work is too small to machine a bearing surface for the adjustable jaws to hold, then a cathead should be
used. The cathead has a bearing surface, a hole through which the work extends, and adjusting screws. The adjusting
screws fasten the cathead to the work. They are also used to align the bearing surface so that it is concentric to the
work axis. A dial indicator must be used to set up the cathead to be concentric and accurate.

Follower Rest

The follower rest has one or two jaws that bear against the workpiece. The rest is fastened to the lathe carriage so
that it will follow the tool bit and bear upon the portion of the workpiece that has just been turned. The cut must
first be started and continued for a short longitudinal distance before the follower rest may be applied. The rest is
generally used only for straight turning and for threading long, thin workpieces. Steady rests and follower rests can
be equipped with ball-bearing surfaces on the adjustable jaws. These types of rests can be used without excessive
lubricant or having to machine a polished bearing surface.

Micrometer Carriage Stop

The micrometer carriage stop, Figure 7-28, is used to accurately position the lathe carriage. The micrometer stop is
designed so the carriage can be moved into position against the retractable spindle of the stop and locked into place.
A micrometer gage on the stop enables carriage movement of as little as 0.001 inch. This tool is very useful when
facing work to length, turning a shoulder, or cutting an accurate groove.

Tool Post Grinder

The tool post grinder (Figure 7-29) is a machine tool attachment specially designed for cylindrical grinding operations
on the lathe. It consists primarily of a 1/4-or 1/3-horsepower electric motor and a wheel spindle connected by
pulleys and a belt. The machine fastens to the compound rest of the lathe with a T-slot bolt which fits in the slot of
the compound rest in the same manner as the lathe tool post. The tool post grinding machine mounts grinding
abrasive wheels ranging from 1/4 inch to 3 or 4 inches in diameter for internal and external grinding operations. The
pulleys on the wheel spindle and motor shaft are interchangeable to provide proper cutting speeds for the various
wheel sizes. The larger grinding abrasive wheels used for external grinding are attached to the wheel spindle with an
arbor. Small, mounted grinding abrasive wheels for internal grinding are fixed in a chuck which screws to the wheel
spindle. The electric motor is connected to an electrical power source by a cable and plug. A switch is usually
provided at the attachment to facilitate starting and stopping the motor.

Lathe Milling Fixture

This is a fixture designed to provide the ability for limited milling operations. Many repair and fabrication jobs cannot
be satisfactorily completed on the standard engine lathe, but with the lathe milling attachment, the small machine
shop that is not equipped with a milling machine can mill keyslots, keyways, flats, angles, hex heads, squares, splines,
and holes. For specific operating instructions and parts, refer to TM 9-3465-200-10.

TOOLS NECESSARY FOR LATHE WORK

In order to properly setup and operate most engine lathes, it is recommended to have the following tools on hand. A
machinist tool box with all wrenches, screwdrivers, and common hand tools. A dial indicator may be necessary for
some procedures on the lathe. References, charts, tables, and other predetermined data on machine operations may
be useful to lathe operators. Keep all safety equipment, along with necessary cleaning marking, and lubricating
equipment, in the immediate lathe area to use as needed.
CUTTING FLUIDS

The purposes of using cutting fluids on the lathe are to cool the tool bit and workpiece that are being machined,
increase the life of the cutting tool, make a smoother surface finish, deter rust, and wash away chips. Cutting fluids
can be sprayed, dripped, wiped, or flooded onto the point where the cutting action is taking place. Generally, cutting
fluids should only be used if the speed or cutting action requires the use of cutting fluids. Descriptions of some
common cutting fluids used on the lathe follow.

Lard Oil

Pure lard oil is one of the oldest and best cutting oils. It is especially good for thread cutting, tapping, deep hole
drilling, and reaming. Lard oil has a high degree of adhesion or oiliness, a relatively high specific heat, and its fluidity
changes only slightly with temperature. It is an excellent rust preventive and produces a smooth finish on the
workpiece. Because lard oil is expensive, it is seldom used in a pure state but is combined with other ingredients to
form good cutting oil mixtures.

Mineral Oil

Mineral oils are petroleum-base oils that range in viscosity from kerosene to light paraffin oils. Mineral oil is very
stable and does not develop disagreeable odors like lard oil; however, it lacks some of the good qualities of lard oil
such as adhesion, oiliness, and high specific heat. Because it is relatively inexpensive, it is commonly mixed with lard
oil or other chemicals to provide cutting oils with desirable characteristics. Two mineral oils, kerosene and
turpentine, are often used alone for machining aluminum and magnesium. Paraffin oil is used alone or with lard oil
for machining copper and brass.

Mineral-Lard Cutting Oil Mixture

Various mixtures of mineral oils and lard oil are used to make cutting oils which combine the good points of both
ingredients but prove more economical and often as effective as pure lard oil.

Sulfurized Fatty-Mineral Oil

Most good cutting oils contain mineral oil and lard oil with various amounts of sulfur and chlorine which give the oils
good antiweld properties and promote free machining. These oils play an important part in present-day machining
because they provide good finishes on most materials and aid the cutting of tough material.

Soluble Cutting Oils

Water is an excellent cooling medium but has little lubricating value and hastens rust and corrosion. Therefore,
mineral oils or lard oils which can be mixed with water are often used to form a cutting oil. A soluble oil and water
mix has lubricating qualities dependent upon the strength of the solution. Generally, soluble oil and water is used for
rough cutting where quick dissipation of heat is most important. Borax and trisodium phosphate (TSP) are sometimes
added to the solution to improve its corrosion resistance.

Soda-Water Mixtures

Salts such as soda ash and TSP are sometimes added to water to help control rust. This mixture is the cheapest of all
coolants and has practically no lubricating value. Lard oil and soap in small quantities are sometimes added to the
mixture to improve its lubricating qualities. Generally, soda water is used only where cooling is the prime
consideration and lubrication a secondary consideration. It is especially suitable in reaming and threading operations
on cast iron where a better finish is desired.

White Lead and Lard Oil Mixture

White lead can be mixed with either lard oil or mineral oil to form a cutting oil which is especially suitable for difficult
machining of very hard metals.

LAYING OUT AND MOUNTING WORK

There is relatively little layout work to be done for most lathe work because of the lathe's ability to guide the cutting
tool accurately to the workpiece. If center holes must be located and drilled into the end of a workpiece for turning
lay out and center-punch the workpiece using other methods. Some suggested methods are to use a bell-type center
punch between centers and this cannot be accomplished on the lathe, (Figure 7-32), use hermaphrodite calipers to
scribe intersecting arcs, use the centering head of the combination square, or use dividers (Figure 7-33).

METHODS OF MOUNTING WORK

Mounting Workpieces in Chucks

When installing the chuck or any attachment that screws onto the lathe headstock spindle, the threads and bearing
surfaces of both spindle and chuck must be cleaned and oiled. In cleaning the internal threads of the chuck, a spring
thread cleaner is very useful (Figure 7-34).

Turn the spindle so that the key is facing up and lock the spindle in position. Make sure that the spindle and chuck
taper are free of grit and chips. Place the chuck in position on the spindle. Engage the draw nut thread and tighten by
applying four or five hammer blows on the spanner wrench engaged with the draw nut. Rotate the spindle 180�,
engage the spanner wrench, and give four or five solid hammer blows to the spanner wrench handle. The workpiece
is now ready for mounting.

Work automatically centers itself in the universal (3 jaw) scroll chuck, drill chuck, collet chucks, and step chuck, but
must be manually centered in the independent (4 jaw) chuck. To center work in the independent chuck, line the four
jaws up to the concentric rings on the face of the chuck, as close to the required diameter as possible.

Mount the workpiece and tighten the jaws loosely onto the workpiece (Figure 7-35). Spin the workpiece by hand and
make approximate centering adjustments as needed, then firmly tighten the jaws.

For rough centering irregularly shaped work, first measure the outside diameter of the workpiece, then open the
four jaws of the chuck until the workpiece slides in. Next tighten each opposing jaw a little at a time until the
workpiece is held firmly, but not too tightly. Hold a piece of chalk near the workpiece and revolve the chuck slowly
with your left hand. Where the chalk touches is considered the high side.

Loosen the jaw opposite and tighten the jaw where the chalk marks are found. Repeat the process until the
workpiece is satisfactorily aligned.

To center a workpiece having a smooth surface such as round stock, the best method is to use a dial test indicator.
Place the point of the indicator against the outside or inside diameter of the workpiece. Revolve the workpiece
slowly by hand and notice any deviations on the dial. This method will indicate any inaccuracy of the centering in
thousandths of an inch.

If an irregularly shaped workpiece is to be mounted in the independent chuck, then a straight, hardened steel bar
can be used with a dial indicator to align the workpiece. Experienced machinists fabricate several sizes of hardened
steel bars, ground with a 60� point, that can be mounted into the drill chuck of the tailstock spindle and guided into
the center-punched mark on the workpiece. A dial indicator can then be used to finish aligning the workpiece to
within 0.001 inch. If a hardened steel bar is not readily available, a hardened center mounted in the tailstock spindle
may be used to align the work while using a dial indicator on the chuck jaws. This method is one of several ways to
align a workpiece in an independent chuck. Ingenuity and experience will increase the awareness of the machine
operator to find the best method to set up the work for machining.

When removing chucks from the lathe, always use a wooden chuck block under the chuck to support the chuck on
the lathe ways. Use care to avoid dropping the chuck on the ways, since this can greatly damage the lathe ways or
crush the operator's hands.

Mounting Work to Faceplates

Mount faceplates in the same manner as chucks. Check the accuracy of the faceplate surface using a dial indicator,
and true the-faceplate surface by taking a light cut if necessary. Do not use faceplates on different lathes, since this
will cause excessive wear of the faceplate due to repeated truing cuts having to be taken. Mount the workpiece using
T-bolts and clamps of the correct sizes (Figure 7-36 ). Ensure all surfaces are wiped clean of burrs, chips, and dirt.
When a heavy piece of work is mounted off center, such as when using an angle plate, use a counterweight to offset
the throw of the work and to minimize vibration and chatter. Use paper or brass shims between the work and the
faceplate to protect the delicate surface of the faceplate. After mounting the work to an approximate center location,
use a dial indicator to finish accurate alignment.

Mounting Work Between Centers

Before mounting a work-piece between centers, the workpiece ends must be center-drilled and countersunk. This
can be done using a small twist drill followed by a 60� center countersink or, more commonly, using a countersink
and drill (also commonly called a center drill). It is very important that the center holes are drilled and countersunk
so that they will fit the lathe centers exactly. Incorrectly drilled holes will subject the lathe centers to unnecessary
wear and the workpiece will not run true because of poor bearing surfaces. A correctly drilled and countersunk hole
has a uniform 60� taper and has clearance at the bottom for the point of the lathe center. Figure 7-37 illustrates
correctly and incorrectly drilled center holes. The holes should have a polished appearance so as not to score the
lathe centers. The actual drilling and countersinking of center holes can be done on a drilling machine or on the lathe
itself. Before attempting to center drill using the lathe, the end of the workpiece must be machined flat to keep the
center drill from running off center.

Mount the work in a universal or independent chuck

and mount the center drill in the lathe tailstock
(Figure 7-38). Refer to the section of this chapter on
facing and drilling on the lathe, prior to doing this
operation. Center drills come in various sizes for
different diameters of work (Figure 7-39). Calculate
the correct speed and hand feed into the workpiece.
Only drill into the workpiece about 2/3 of the body
diameter. high speeds and feed them into the work
slowly to avoid breaking off the drill point inside the
work. If this happens, the work must be removed
from the chuck and the point extracted. This is a
time-consuming job and could ruin the workpiece.

To mount work between centers, the operator must

know how to insert and remove lathe centers. The
quality of workmanship depends as much on the
condition of the lathe centers as on the proper
drilling of the center holes. Before mounting lathe
centers in the headstock or tailstock, thoroughly
clean the centers, the center sleeve, and the tapered
sockets in the headstock and tailstock spindles. Any
dirt or chips on the centers or in their
sockets will prevent the centers from
seating properly and will cause the
centers to run out of true.

Install the lathe center in the tailstock

spindle with a light twisting motion to
ensure a clean fit. Install the center
sleeve into the headstock spindle and
install the lathe center into the center
sleeve with a light twisting motion.

To remove the center from the

headstock spindle, hold the pointed
end with a cloth or rag in one hand and
give the center a sharp tap with a rod
or knockout bar inserted through the
hollow headstock spindle.
To remove the center from the tailstock, turn the tailstock handwheel to draw the tailstock spindle into the tailstock.
The center will contact the tailstock screw and will be bumped loose from its socket.

After mounting the headstock and

tailstock centers, the accuracy of the
60� point should be checked using a
center gage or a dial indicator. If the
center in the headstock is not at 60�,
or is scarred and burred, it must be
trued while inserted in the lathe
headstock spindle. If the headstock
center is a soft center (a center that is
not heat-treated and hardened), it can
be turned true with the lathe tool bit. If
the center in the headstock is hardened,
it must be ground with a tool post
grinding machine to get a true surface
(Figure 7-40).

To turn a soft center true with the lathe,

first set up the tool bit for right hand
turning, center the tool bit; then, rotate
the compound rest to an angle of 30�
to the axis of the lathe (Figure 7-41). The
lathe speed should be set for a finish
cut, and the feed is supplied by cranking
the handwheel of the compound rest,
thus producing a clean and short steep
taper with an included angle of 60�.
Once trued, the center should stay in
place until the operation is completed. If
the center must be removed, mark the
position on the center and headstock for
easy realignment later.

Lathe centers must be parallel with the

ways of the lathe in order to turn
workpieces straight and true. Before
beginning each turning operation, the
center alignment should be checked.

The tailstock may be moved laterally to

accomplish this alignment by means of
adjusting screws after it has been
released from the ways. Two zero lines
are located at the rear of the tailstock
and the centers are approximately
aligned when these lines coincide (Figure 7-42). This alignment may be checked by moving the tailstock up close to
the headstock so that the centers almost touch, and observing their relative positions (Figure 7-42).
The most accurate method of checking alignment of centers is by mounting the workpiece between centers and
taking light cuts at both ends without changing the carriage adjustments. Measure each end of this cut with calipers
or a micrometer. If the tailstock end is greater in diameter than the headstock end, the tailstock is moved toward the
operator. If the tailstock end is smaller in diameter than the headstock end, the tailstock is moved away from the
operator. Take additional cuts in the same manner after each adjustment until both cuts measure the same.

To setup the workpiece between centers on the lathe, a driving faceplate (drive plate) and lathe dog must be used.

(Figure 7-43). Make headstock spindle are faceplate. Screw the sure that the external threads of the clean before
screwing on the driving faceplate securely onto the spindle. Clamp the lathe dog on the workpiece so that its tail
hangs over the end of the workpiece. If the workpiece is finished, place a shim of soft material such as brass between
the setscrew of the dog and workpiece. Mount the workpiece between the centers. Make sure that the lathe dog tail
tits freely in the slot of the faceplate and does not bind. Sometimes, the tailstock center is a dead center and does
not revolve with the workpiece, so it
may require lubrication. A few drops
of oil mixed with white lead should be
applied to the center before the
workpiece is set up. The tailstock
should be adjusted so that the
tailstock center fits firmly into the
center hole of the workpiece but does
not bind. The lathe should be stopped
at intervals and additional oil and
white lead mixture applied to the
dead center to prevent overheating
harm to the center and the workpiece.

Mounting Work on Mandrels

To machine a workpiece of an odd

shape, such as a wheel pulley, a tapered mandrel is used to hold and turn the work. The mandrel must be mounted
between centers and a drive plate and lathe dog must be used. The centers must be aligned and the mandrel must
be free of burrs. Mount the workpiece onto a lubricated mandrel of the proper size by using an arbor press. Ensure
that the lathe dog is secured to the machined flat on the end of the mandrel and not on the smooth surface of the
mandrel taper (Figure 7-44). If expansion bushings are to be used with a mandrel, clean and care for the expansion
bushings in the same manner as a normal mandrel.
Always feed the tool bit in the direction of the large end of the mandrel, which is usually toward the headstock end,
to avoid pulling the work out of the mandrel. If facing on a mandrel, avoid cutting into the mandrel with the tool bit..

GENERAL LATHE OPERATIONS

LATHE SPEEDS, FEEDS, AND DEPTH OF CUTS

General operations on the lathe include straight and shoulder turning, facing, grooving, parting, turning tapers, and
cutting various screw threads. Before these operations can be done, a thorough knowledge of the variable factors of
lathe speeds, feeds, and depth of cut must be understood. These factors differ for each lathe operation, and failure to
use these factors properly will result in machine failure or work damage. The kind of material being worked, the type
of tool bit, the diameter and length of the workpiece, the type of cut desired (roughing or finishing), and the working
condition of the lathe will determine which speed, feed, or depth of cut is best for any particular operation. The
guidelines which follow for selecting speed, feed, and depth of cut are general in nature and may need to be changed
as conditions dictate.

Cutting Speeds.

The cutting speed of a tool bit is defined as the number of feet of workpiece surface, measured at the circumference,
that passes the tool bit in one minute. The cutting speed, expressed in FPM, must not be confused with the spindle
speed of the lathe which is expressed in RPM. To obtain uniform cutting speed, the lathe spindle must be revolved
faster for workpieces of small diameter and slower for workpieces of large diameter. The proper cutting speed for a
given job depends upon the hardness of the material being machined, the material of the tool bit, and how much
feed and depth of cut is required. Cutting speeds for metal are usually expressed in surface feet per minute,
measured on the circumference of the work. Spindle revolutions per minute (RPM) are determined by using the
formula:

Which is simplified to:

Where SFM is the rated surface feet per minute, also expressed as cutting speed.

RPM is the spindle speed in revolutions per minute

D is the diameter of the work in inches.

In order to use the formula simply insert the cutting speed of the metal and the diameter of the workpiece into the
formula and you will have the RPM.

Turning a one-half inch piece of aluminum, cutting speed of 200 SFM, would result in the following:

Machinist Table 7-2 lists specific ranges of cutting speeds for turning and threading various materials under normal
lathe conditions, using normal feeds and depth of cuts. Note that in Table 7-2 the measurement calculations are in
inch and metric measures. The diameter measurements used in these calculations are the actual working diameters
that are being machined, and not necessarily the largest diameter of the material. The cutting speeds have a wide
range so that the lower end of the cutting speed range can be used for rough cutting and the higher end for finish
cutting. If no cutting speed tables are available, remember that, generally, hard materials require a slower cutting
speed than soft or ductile materials. Materials that are machined dry, without coolant, require a slower cutting speed
than operations using coolant. Lathes that are worn and in poor condition will require slower speeds than machines
that are in good shape. If carbide-tipped tool bits are being used, speeds can be increased two to three times the
speed used for high-speed tool bits.
Feed

Feed is the term applied to the distance the tool bit

advances along the work for each revolution of the lathe
spindle. Feed is measured in inches or millimeters per
revolution, depending on the lathe used and the
operator's system of measurement. Machinist Table 7-3 is
a guide that can be used to select feed for general
roughing and finishing operations. A light feed must be
used on slender and small workpieces to avoid damage. If
an irregular finish or chatter marks develop while turning,
reduce the feed and check the tool bit for alignment and
sharpness. Regardless of how the work is held in the
lathe, the tool should feed toward the headstock. This
results in most of the pressure of the cut being put on the
work holding device. If the cut must be fed toward the
tailstock, use light feeds and light cuts to avoid pulling the
workpiece loose.

Depth of Cut

Depth of cut is the distance that the tool bit moves into the work, usually measured in thousandths of an inch or in
millimeters. General machine practice is to use a depth of cut up to five times the rate of feed, such as rough cutting
stainless steel using a feed of 0.020 inch per revolution and a depth of cut of 0.100 inch, which would reduce the
diameter by 0.200 inch. If chatter marks or machine noise develops, reduce the depth of cut.

MICROMETER COLLAR

Graduated micrometer collars can be used to accurately measure this tool bit movement to and away from the lathe
center axis. Thus, the depth of cut can be accurately measured when moving the tool bit on the cross slide by using
the cross slide micrometer collar. The compound rest is also equipped with a micrometer collar. These collars can
measure in inches or in millimeters, or they can be equipped with a dual readout collar that has both. Some collars
measure the exact tool bit movement, while others are designed to measure the amount of material removed from
the workpiece (twice the tool bit movement). Consult the operator's instruction manual for specific information on
graduated collar use.

FACING

Facing is machining the ends and shoulders of a piece of stock smooth, flat, and perpendicular to the lathe axis.
Facing is used to cut work to the desired length and to produce a surface from which accurate measurements may be
taken.

Facing Work in a Chuck

Facing is usually performed with the work held in a chuck or collet. Allow the workpiece to extend a distance no
more than 1 1/2 times the work diameter from the chuck jaws, and use finishing speeds and feeds calculated using
the largest diameter of the workpiece. The tool bit may be fed from the outer edge to the center or from the center
to the outer edge. Normal facing is done from the outer edge to the center since this method permits the operator to
observe the tool bit and layout line while starting the cut. This method also eliminates the problem of feeding the
tool bit into the solid center portion of the workpiece to get a cut started.. Use a left-hand finishing tool bit and a
right-hand tool holder when facing from the outer edge toward the center. Work that has a drilled or bored hole in
the center may be faced from the center out to the outer edge if a right-hand finishing tool bit is used. Avoid
excessive tool holder and tool bit overhang when setting up the facing operation. Set the tool bit exactly on center to
avoid leaving a center nub on the workpiece (Figure 7-46 ). Use the tailstock center point as a reference point when
setting the tool bit exactly on center. If no tailstock center is available, take a trial cut and readjust as needed. If using
the cross slide power feed to move the tool bit (into the center), disengage power when the tool bit is within l/16
inch of the center and finish the facing cut using hand feed.

Facing Work Between Centers

Sometimes the workpiece will not fit into a chuck or collet, so facing must be done between centers. To properly
accomplish facing between centers, the workpiece must be center-drilled before mounting into the lathe. A half male
center (with the tip well lubricated with a white lead and oil mixture) must be used in the lathe tailstock to provide
adequate clearance for the tool bit. The tool bit must be ground with a sharp angle to permit facing to the very edge
of the center drilled hole (Figure 7-47). Start the facing cut at the edge of the center-drilled hole after checking for
tool bit clearance, and feed the cutting tool out to the edge. Use light cuts and finishing feeds, which will reduce the
tension put on the half male center. Replace the half male center with a standard center after the facing operation,
since the half male center will not provide adequate support for general turning operations. Only a small amount of
material can be removed while facing between centers. If too much material is removed, the center-drilled hole will
become too small to support the workpiece.

Precision Facing
Special methods must be used to face materials to a precise length. One method is to mount the work in a chuck and
lightly face one end with a cleanup cut. Then, reverse the stock and face it to the scribed layout line. This method
may not be as accurate as other methods, but it will work for most jobs. A more precise method to face a piece of
stock to a specified length is to turn the compound rest to an angle of 30 degrees to the cross slide and then use the
graduated micrometer collar to measure tool bit movement, Figure 7-48. At this angle of the compound rest, the
movement of the cutting tool will always be half of the reading of the graduated collar. Thus, if the compound rest
feed is turned 0.010 inch, the tool bit will face off 0.005 inch of material. With the compound rest angled at 30�, a
light cut may be made on the first end, then the piece reversed and faced to accurate length. Always lock the carriage
down to the bed. This provides the most secure and accurate base for the cutting tool and helps eliminate unwanted
vibration during facing operations. Another way to face to a precise length is to use the lathe carriage micrometer
stop to measure the carriage and tool bit movement. Using the micrometer stop can sometimes be faster and easier
than using the compound rest graduated collar for measuring tool bit movement.

STRAIGHT TURNING

Straight turning, sometimes called cylindrical turning, is the process of reducing the work diameter to a specific
dimension as the carriage moves the tool along the work. The work is machined on a plane parallel to its axis so that
there is no variation in the work diameter throughout the length of the cut. Straight turning usually consists of a
roughing cut followed by a finishing cut. When a large amount of material is to be removed, several roughing cuts
may need to be taken. The roughing cut should be as heavy as the machine and tool bit can withstand. The finishing
cut should be light and made to cut to the specified dimension in just one pass of the tool bit. When using power
feed to machine to a specific length, always disengage the feed approximately 1/16-inch away from the desired
length dimension, and then finish the cut using hand feed.

Setting Depth of Cut

In straight turning, the cross feed or compound rest graduated collars are used to determine the depth of cut, which
will remove a desired amount from the workpiece diameter. When using the graduated collars for measurement,
make all readings when rotating the handles in the forward direction. The lost motion in the gears, called backlash,
prevents taking accurate readings when the feed is reversed. If the feed screw must be reversed, such as to restart a
cut, then the backlash must be taken up by turning the feed screw handle in the opposite direction until the
movement of the screw actuates the movement of the cross slide or compound rest. Then turn the feed screw
handle in the original or desired direction back to the required setting.

Setting Tool Bit for Straight Turning

See Figure 7-49. For most straight turning operations, the compound rest should be aligned at an angle perpendicular
to the cross slide, and then swung 30� to the right and clamped in position. The tool post should be set on the left-
hand side of the compound rest T-slot, with a minimum of tool bit and tool holder overhang.
When the compound rest and tool post are in these positions, the danger of running the cutting tool into the chuck
or damaging the cross slide are minimized. Position the roughing tool bit about 5� above center height for the best
cutting action. This is approximately 3/64-inch above center for each inch of the workpiece diameter. The finishing
tool bit should be positioned at center height since there is less torque during finishing. The position of the tool bit to
the work should be set so that if anything occurs during the cutting process to change the tool bit alignment, the tool
bit will not dig into the work, but instead will move away from the work. Also, by setting the tool bit in this position,
chatter will be reduced. Use a right-hand turning tool bit with a slight round radius on the nose for straight turning.
Always feed the tool bit toward the headstock unless turning up to an inside shoulder. Different workpieces can be
mounted in a chuck, in a collet, or between centers. Which work holding device to use will depend on the size of the
work and the particular operation that needs to be performed.

Turning Work Between Centers

Turning work that is held between centers is one accurate method that is available. The chief advantage of using this
method is that the work can be removed from the lathe and later replaced for subsequent machining operations
without disturbing the trueness of the turned surface in relation to the center holes of the workpiece. The lathe
centers must be in good condition and carefully aligned if the turning operation is to be accurate. If necessary, true
the centers and realign as needed. After the workpiece is center-drilled, place a lathe dog (that is slightly larger in
diameter than the workpiece) on the end of the work that will be toward the headstock, and tighten the lathe dog
bolt securely to the workpiece). If using a dead center in the tailstock, lubricate the center with a mixture of white
lead and motor oil. A ball bearing live center is best for the tailstock center since this center would not need
lubrication and can properly support the work. Extend the tailstock spindle out about 3 inches and loosen the
tailstock clamp-down nut. Place the work with the lathe dog end on the headstock live center and slide the tailstock
forward until the tailstock center will support the work; then, secure the tailstock with the clamp-down nut. Adjust
the tail of the lathe dog in the drive plate slot, making sure that the tail does not bind into the slot and force the work
out of the center. A good fit for the lathe dog is when there is clearance at the top and bottom of the drive plate slot
on both sides of the lathe dog tail. Tension should be applied to hold the work in place, but not so much tension that
the tail of the lathe dog will not move freely in the drive -plate slot.
Check tool bit clearance by moving the tool bit to the furthest position that can be cut without running into the lathe
dog or the drive plate. Set the lathe carriage stop or micrometer carriage stop at this point to reference for the end of
the cut and to protect the lathe components from damage. Set the speed, feed, and depth of cut for a roughing cut
and then rough cut to within 0.020 inch of the final dimension. Perform a finish cut, flip the piece over, and change
the lathe dog to the opposite end. Then rough and finish cut the second side to final dimensions.

Turning Work in Chucks

Some work can be machined more efficiently by using chucks, collets, mandrels, or faceplates to hold the work.
Rough and finish turning using these devices is basically the same as for turning between centers. The workpiece
should not extend too far from the work holding device without adequate support. If the work extends more than
three times the diameter of the workpiece from the chuck or collet, additional support must be used such as a steady
rest or a tailstock center support. When turning using a mandrel or faceplate to hold an odd-shaped workpiece, use
light cuts and always feed the cutting tool toward the headstock. Every job may require a different setup and a
different level of skill. Through experience, each machine operator will learn the best methods for holding work to be
turned.

MACHINING SHOULDERS, CORNERS, UNDERCUTS, GROOVES, AND PARTING

Shoulders

Frequently, it will be necessary to machine work that has two or more diameters in its length. The abrupt step, or
meeting place, of the two diameters is called a shoulder. The workpiece may be mounted in a chuck, collet, or
mandrel, or between centers as in straight turning. Shoulders are turned, or formed, to various shapes to suit the
requirements of a particular part. Shoulders are machined to add strength for parts that are to be fitted together,
make a corner, or improve the appearance of a part. The three common shoulders are the square, the filleted, and
the angular shoulder (Figure 7-50).

Square shoulders are used on work that is not subject to excessive strain at the corners. This shape provides a flat
clamping surface and permits parts to be fitted squarely together. There are many different ways to accurately
machine a square shoulder. One method is to use a parting tool bit to locate and cut to depth the position of the
shoulder. Straight-turning the diameter down to the desired size is then the same as normal straight turning. Another
method to machine a square shoulder is to rough out the shoulder slightly oversize with a round-nosed tool bit, and
then finish square the shoulders to size with a side-finishing tool bit. Both of these methods are fine for most work,
but may be too time-consuming for precise jobs. Shoulders can be machined quickly and accurately by using one
type of tool bit that is ground and angled to straight turn and face in one operation (Figure 7-51).
Set up the micrometer carriage stop to align the shoulder dimension; then, in one pass of the tool bit, feed the tool
bit left to turn the smaller diameter until contact is made with the carriage stop. Change the direction to feed out
from center and face the shoulder out to the edge of the workpiece. The lathe micrometer stop measures the length
of the shoulder and provides for a stop or reference for the tool bit. Shoulder turning in this manner can be
accomplished with a few roughing cuts and a finishing cut.

Filleted Shoulders

Filleted shoulders or corners, are rounded to be used on parts which require additional strength at the shoulder.
These shoulders are machined with a round-nose tool bit or a specially formed tool bit (Figure 7-52). This type of
shoulder can be turned and formed in the same manner as square shoulders. Filleted corners are commonly cut to
double-sided shoulders (see Undercuts).

Angular Shoulders

Angular shoulders although not as common as filleted shoulders, are sometimes used to give additional strength to
corners, to eliminate sharp corners, and to add to the appearance of the work. Angular shoulders do not have all the
strength of filleted corners but are more economical to produce due to the simpler cutting tools. These shoulders are
turned in the same manner as square shoulders by using a side turning tool set at the desired angle of the shoulder,
or with a square-nosed tool set straight into the work (Figure 7-53).
Corners

Corners are turned on the edges of work to break down sharp edges and to add to the general appearance of the
work. Common types of corners are chamfered, rounded, and square (Figure 7-54). Chamfered (or angular) corners
may be turned with the side of a turning tool or the end of a square tool bit, as in angular shoulder turning. Round
corners are produced by turning a small radius on the ends of the work. The radius may be formed by hand
manipulation of the cross slide and carriage using a turning tool. An easier method is to use a tool bit specifically
ground for the shape of the desired corner. Still another method is to file the radius with a standard file. A square
corner is simply what is left when making a shoulder, and no machining is needed.

Undercuts

Undercuts are the reductions in diameter machined onto the center portion of workpieces (Figure 7-55) to lighten
the piece or to reduce an area of the part for special reasons, such as holding an oil seal ring. Some tools, such as
drills and reamers, require a reduction in diameter at the ends of the flutes to provide clearance or runout for a
milling cutter or grinding wheel. Reducing the diameter of a shaft or workpiece at the center with filleted shoulders
at each end may be accomplished by the use of a round-nosed turning tool bit. This tool bit may or may not have a
side rake angle, depending on how much machining needs to be done. A tool bit without any side rake is best when
machining in either direction. Undercutting is done by feeding the tool bit into the workpiece while moving the
carriage back and forth slightly. This prevents gouging and chatter occurring on the work surface.
Grooves

Grooving (or necking) is the process of turning a groove or furrow on a cylinder, shaft, or workpiece. The shape of the
tool and the depth to which it is fed into the work govern the shape and size of the groove. The types of grooves
most commonly used are square, round, and V-shaped (Figure 7-56). Square and round grooves are frequently cut on
work to provide a space for tool runout during subsequent machining operations, such as threading or knurling.
These grooves also provide a clearance for assembly of different parts. The V-shaped groove is used extensively on
step pulleys made to fit a V-type belt. The grooving tool is a type of forming tool. It is ground without side or back
rake angles and set to the work at center height with a minimum of overhang. The side and end relief angles are
generally somewhat less than for turning tools.

In order to cut a round groove of a definite radius on a cylindrical surface, the tool bit must be ground to fit the
proper radius gage (Figure 7-57). Small V-grooves may be machined by using a form tool ground to size or just slightly
undersize. Large V-grooves may be machined with the compound rest by finishing each side separately at the desired
angle. This method reduces tool bit and work contact area, thus reducing chatter, gouging, and tearing. Since the
cutting surface of the tool bit is
generally broad, the cutting speed
must be slower than that used for
general turning. A good guide is to use
half of the speed recommended for
normal turning. The depth of the
groove, or the diameter of the
undercut, may be checked by using
outside calipers or by using two wires
and an outside micrometer (Figure 7-
58).
 When a micrometer and two wires are used, the
micrometer reading is equal to the measured diameter of
the groove plus two wire diameters.

To calculate measurement over the wires, use the

following formula:

Measurement = Outside Diameter + (2 x wires) - 2 x

radius).

Parting

Parting is the process of cutting off a piece of stock while it

is being held in the lathe. This process uses a specially
shaped tool bit with a cutting edge similar to that of a
square-nosed tool bit. When parting, be sure to use plenty
of coolant, such as a sulfurized cutting oil (machine cast
iron dry). Parting tools normally have a 5� side rake and
no back rake angles. The blades are sharpened by grinding
the ends only. Parting is used to cut off stock, such as
tubing, that is impractical to saw off with a power
hacksaw.

Parting is also used to cut off work after other machining

operations have been completed (Figure 7-59). Parting tools can be of the forged type, inserted blade type, or ground
from a standard tool blank. In order for the tool to have maximum strength, the length of the cutting portion of the
blade should extend only enough to be slightly longer than half of the workpiece diameter (able to reach the center
of the work). Never attempt to part while the work is mounted between centers.

Work that is to be parted should be held rigidly in a chuck or

collet, with the area to be parted as close to the holding
device as possible. Always make the parting cut at a right
angle to the centerline of the work. Feed the tool bit into
the revolving work with the cross slide until the tool
completely severs the work. Speeds for parting should be
about half that used for straight turning. Feeds should be
light but continuous. If chatter occurs, decrease the feed
and speed, and check for loose lathe parts or a loose setup.
The parting tool should be positioned at center height
unless cutting a piece that is over 1-inch thick. Thick pieces
should have the cutting tool just slightly above center to
account for the stronger torque involved in parting. The
length of the portion to be cut off can be measured by using
the micrometer carriage stop or by using layout lines scribed
on the workpiece. Always have the carriage locked down to
the bed to reduce vibration and chatter. Never try to catch the cutoff part in the hand; it will be hot and could burn.

RADII AND FORM TURNING

Occasionally, a radius or irregular shape must be machined on the lathe. Form turning is the process of machining
radii and these irregular shapes. The method used to form-turn will depend on the size and shape of the object, the
accuracy desired, the time allowed, and the number of pieces that need to be formed. Of the several ways to form-
turn, using a form turning tool that is ground to the shape of the desired radius is the most common. Other common
methods are using hand manipulation and filing, using a template and following rod, or using the compound rest and
tool to pivot and cut. Two radii are cut in form turning, concave and convex. A concave radius curves inward and a
convex radius curves outward.

Forming a Radius Using a Form Turning Tool

Using a form turning tool to cut a radius is a way to form small radii and contours that will fit the shape of the tool.
Forming tools can be ground to any desired shape or contour (Figure 7-60), with the only requirements being that
the proper relief and rake angles must be ground into the tool's shape. The most practical use of the ground forming
tool is in machining several duplicate pieces, since the machining of one or two pieces will not warrant the time
spent on grinding the form tool. Use the proper radius gage to check for correct fit. A forming tool has a lot of contact
with the work surface, which can result in vibration and chatter. Slow the speed, increase the feed, and tighten the
work setup if these problems occur.

Forming a Radius Using Hand Manipulation

Hand manipulation, or free hand, is the most difficult method of form turning to master. The cutting tool moves on
an irregular path as the carriage and cross slide are simultaneously manipulated by hand. The desired form is
achieved by watching the tool as it cuts and making small adjustments in the movement of the carriage and cross
slide. Normally, the right hand works the cross feed movement while the left hand works the carriage movement.
The accuracy of the radius depends on the skill of the operator. After the approximate radius is formed, the
workpiece is filed and polished to a finished dimension.

Forming a Radius Using a Template

To use a template with a follower rod to form a radius, a full scale form of the work is laid out and cut from thin sheet
metal. This form is then attached to the cross slide in such a way that the cutting tool will follow the template. The
accuracy of the template will determine the accuracy of the workpiece. Each lathe model has a cross slide and
carriage that are slightly different from one another, but they all operate in basically the same way. A mounting
bracket must be fabricated to hold the template to allow the cutting tool to follow its shape. This mounting bracket
can be utilized for several different operations, but should be sturdy enough for holding clamps and templates. The
mounting bracket must be positioned on the carriage to allow for a follower (that is attached to the cross slide) to
contact the template and guide the cutting tool. For this operation, the cross slide must be disconnected from the
cross feed screw and hand pressure applied to hold the cross slide against the follower and template. Rough-cut the
form to the approximate shape before disconnecting the cross feed screw. This way, a finish cut is all that is required
while applying hand pressure to the cross slide. Some filing may be needed to completely finish the work to
dimension.

Forming a Radius Using the Compound Rest

To use the compound rest and tool to pivot and cut (Figure 7-61), the compound rest bolts must be loosened to allow
the compound rest to swivel. When using this method, the compound rest and tool are swung from side to side in an
arc. The desired radius is formed by feeding the tool in or out with the compound slide. The pivot point is the center
swivel point of the compound rest. A concave radius can be turned by positioning the tool in front of the pivot point,
while a convex radius can be turned by placing the
tool behind the pivot point. Use the micrometer
carriage stop to measure precision depths of different
radii.

TAPER TURNING

When the diameter of a piece changes uniformly from

one end to the other, the piece is said to be tapered.
Taper turning as a machining operation is the gradual
reduction in diameter from one part of a cylindrical
workpiece to another part. Tapers can be either
external or internal. If a workpiece is tapered on the
outside, it has an external taper; if it is tapered on the
inside, it has an internal taper. There are three basic
methods of turning tapers with a lathe. Depending on
the degree, length, location of the taper (internal or
external), and the number of pieces to be done, the
operator will either use the compound rest, offset the
tailstock, or use the taper attachment. With any of
these methods the cutting edge of the tool bit must be
set exactly on center with the axis of the workpiece or
the work will not be truly conical and the rate of taper
will vary with each cut.

Compound Rests

The compound rest is favorable for turning or boring

short, steep tapers, but it can also be used for longer, gradual tapers providing the length of taper does not exceed
the distance the compound rest will move upon its slide. This method can be used with a high degree of accuracy,
but is somewhat limited due to lack of automatic feed and the length of taper being restricted to the movement of
the slide.

The compound rest base is graduated in degrees and can be set at the required angle for taper turning or boring.
With this method, it is necessary to know the included angle of the taper to be machined. The angle of the taper with
the centerline is one-half the included angle and will be the angle the compound rest is set for. For example, to true
up a lathe center which has an included angle of 60�, the compound rest would be set at 30� from parallel to the
ways (Figure 7-41).

If there is no degree of angle given for a particular job, then calculate the compound rest setting by finding the taper
per inch, and then calculating the tangent of the angle (which is the: compound rest setting) .

For example, the compound rest setting for the workpiece shown in Figure 7-62 would be calculated in the following
manner

Where TPI = taper per inch

D =large diameter,
 d =small diameter,

L =length of taper

angl
=compound rest setting
e

The problem is actually worked out by substituting numerical values for the letter variables:

Apply the formula to find the angle by substituting the numerical values for the letter variables:

Using the trig charts in TC 9-515 or any other source of trig charts, the TAN of 0.41650 is found to be 22�37'. This
angle is referred to as 22 degrees and 37 minutes.

To machine the taper shown in Figure 7-62, the compound rest will be set at 22�37 '. Since the base of the
compound rest is not calibrated in minutes, the operator will set the base to an approximate degree reading, make
trial cuts, take measurements, and readjust as necessary to obtain the desired angle of taper. The included angle of
the workpiece is double that of the tangent of angle (compound rest setting). In this case, the double of 22�37'
would equal the included angle of 45�14'.

To machine a taper by this method, the tool bit is set on center with the workpiece axis. Turn the compound rest feed
handle in a counterclockwise direction to move the compound rest near its rear limit of travel to assure sufficient
traverse to complete the taper. Bring the tool bit into position with the workpiece by traversing and cross-feeding the
carriage. Lock the carriage to the lathe bed when the tool bit is in position. Cut from right to left, adjusting the depth
of cut by moving the cross feed handle and reading the calibrated collar located on the cross feed handle. feed the
tool bit by hand-turning the compound rest feed handle in a clockwise direction.
Offsetting the Tailstock

The oldest and probably most used method of taper turning is the offset tailstock method. The tailstock is made in
two pieces: the lower piece is fitted to the bed, while the upper part can be adjusted laterally to a given offset by use
of adjusting screws and lineup marks (Figure 7-63).

Since the workpiece is mounted between centers, this method of taper turning can only be used for external tapers.
The length of the taper is from headstock center to tailstock center, which allows for longer tapers than can be
machined using the compound rest or taper attachment methods.

The tool bit travels along a line which is parallel with the ways of the lathe. When the lathe centers are aligned and
the workpiece is machined between these centers, the diameter will remain constant from one end of the piece to
the other. If the tailstock is offset, as shown in Figure 7-64, the centerline of the workpiece is no longer parallel with
the ways; however, the tool bit continues its parallel movement with the ways, resulting in a tapered workpiece. The
tailstock may be offset either toward or away from the operator. When the offset is toward the operator, the small
end of the workpiece will be at the tailstock with the diameter increasing toward the headstock end.
The offset tailstock method is applicable only to comparatively gradual tapers because the lathe centers, being out of
alignment, do not have full bearing on the workpiece. Center holes are likely to wear out of their true positions if the
lathe centers are offset too far, causing poor results and possible damage to centers.

The most difficult operation in taper turning by the offset tailstock method is determining the proper distance the
tailstock should be moved over to obtain a given taper. Two factors affect the amount the tailstock is offset: the taper
desired and the length of the workpiece. If the offset remains constant, workpieces of different lengths, or with
different depth center holes, will be machined with different tapers (Figure 7-65).

The formula for calculating the tailstock offset when the taper is given in taper inches per foot (tpf) is as follows

Where: =tailstock offset (in inches)

Offset

TPF =taper (in inches per foot)

L =length of taper (in feet) measured along the axis of the workpiece

For example, the amount of offset required to machine a bar 42 inches (3.5 feet) long with a taper of 1/2 inch per
foot is calculated as follows:
Therefore, the tailstock should be offset 0.875 inch to machine the required taper. The formula for calculating the
tailstock offset when the taper is given in TPF is as follows:

Where OFFSE =tailstock offset

T

TPI =taper per inch

L =length of taper in inches

For example, the amount of offset required to machine a bar 42 inches long with a taper of 0.0416 TPI is calculated
as follows:

Therefore, the tailstock should be offset 0.875 inch to machine the required taper.

If the workpiece has a short taper in any par of it's length and the TPI or TPF is not given, use the following formula:

Where :

D = Diameter of large end

d = Diameter of small end

L = Total length of workpiece in inches diameter (in inches)

L1 = Length of taper
For example, the amount of tailstock offset required to machine a bar 36 inches (3 feet) in length for a distance of 18
inches (1.5 feet) when the large diameter is 1 3/4 (1 .750) inches and the small diameter is 1 1/2 (1.5) inches is
calculated as follows

Therefore, the tailstock would be offset (toward the operator) 0.25 inch to machine the required taper.

Metric tapers can also be calculated for taper turning by using the offset tailstock method. Metric tapers are
expressed as a ratio of 1 mm per unit of length. Figure 7-66 shows how the work would taper 1 mm in a distance of
20 mm. This taper would then be given as a ratio of 1:20 and would be annotated on small diameter (d) will be 1 mm
greater (d + ). Refer to the following formula for calculating the dimensions of a metric taper. If the small diameter
(d), the unit length of taper (k), and the total length of taper (1) are known, then the large diameter (D) may be
calculated. The large diameter (D) will be equal to the small diameter plus the amount of taper. The amount of taper
for the unit length (k) is (d + 1) -(d). Therefore, the amount of taper per millimeter of unit length = (l/k). The total
amount of taper will be the taper per millimeter (l/k) multiplied by the total length of taper (l).

For example, to calculate for the large diameter D for a 1:30

taper having a small diameter of 10 mm and a length of 60 mm, do the following:

Since the taper is the ratio 1:30, then (k)= 30, since 30 is the unit of length.
Tailstock offset is calculated as follows:

Tailstock offset =

D= large diameter

d= small diameter

I = length of taper

L = length of the workpiece

Thus, to determine the tailstock offset in millimeters for the taper in Figure 7-67, substitute the numbers and solve
for the offset. Calculate the tailstock offset required to turn a 1:50 taper 200 mm long on a workpiece 800 mm long.
The small diameter of the tapered section is 49 mm.

The tailstock would be moved toward the operator 8 mm.

Another important consideration in calculating offset is the distance the lathe centers enter the workpiece. The
length of the workpiece (L) should be considered as the distance between the points of the centers for all offset
computations.

Therefore, if the centers enter the workpiece 1/8 inch on each end and the length of the workpiece is 18 inches,
subtract 1/4 inch from 18 inches and compute the tailstock offset using 17 3/4 inches as the workpiece length (L).

The amount of taper to be cut will govern the distance the top of the tailstock is offset from the centerline of the
lathe. The tailstock is adjusted by loosening the clamp nuts, shifting the upper half of the tailstock with the adjusting
screws, and then tightening them in place.

There are several methods the operator may use to measure the distance the tailstock has been offset depending
upon the accuracy desired (Figure 7-68 ).

One method is to gage the distance the lineup marks on the rear of the tailstock have moved out of alignment. This
can be done by using a 6-inch rule placed near the lineup marks or by transferring the distance between the marks to
the rule's surface using a pair of dividers.

Another common method uses a rule to check the amount of offset when the tailstock is brought close to the
headstock.

Where accuracy is required, the amount of offset may be measured by means of the graduated collar on the cross
feed screw. First compute the amount of offset; next, set the tool holder in the tool post so the butt end of the holder
faces the tailstock spindle. Using the cross feed, run the tool holder in by hand until the butt end touches the
tailstock spindle. The pressure should be just enough to hold a slip of paper placed between the tool holder and the
spindle. Next, move the cross slide to bring the tool holder toward you to remove the backlash. The reading on the
cross feed micrometer collar may be recorded, or the graduated collar on the cross feed screw may be set at zero.
Using either the recorded reading or the zero setting for a starting point, bring the cross slide toward you the
distance computed by the offset. Loosen and offset the tailstock until the slip of paper drags when pulled between
the tool holder and the spindle. Clamp the tailstock to the lathe bed.

Another and possibly the most precise method of measuring the offset is to use a dial indicator. The indicator is set
on the center of the tailstock spindle while the centers are still aligned. A slight loading of the indicator is advised
since the first 0.010 or 0.020 inches of movement of the indicator may be inaccurate due to mechanism wear causing
fluctuating readings. Load the dial indicators follows: Set the bezel to zero and move tailstock towards the operator
the calculated Famount. Then clamp the tailstock to the way.

Whichever method is used to offset the tailstock, the offset must still be checked before starting to cut. Set the dial
indicator in the tool post with its spindle just barely touching far right side of the workpiece. Then, rotate the carriage
toward the headstock exactly 1 inch and take the reading from the dial indicator. One inch is easily accomplished
using the thread chasing dial. It is 1 inch from one number to another.

Alternatively, 1 inch can be drawn out on the workpiece. The dial indicator will indicate the taper for that 1 inch and,
if needed, the tailstock can be adjusted as needed to the precise taper desired. If this method of checking the taper is
not used, then an extensive trial and error method is necessary.

To cut the taper, start the rough turning at the end which will be the small diameter and feed longitudinally toward
the large end (Figure 7-64). The tailstock is offset toward the operator and the feed will be from right to left. The tool
bit, a right-hand turning tool bit or a round-nose turning tool bit, will have its cutting edge set exactly on the
horizontal centerline of the workpiece, not above center as with straight turning.

Taper Attachment

The taper attachment (Figure 7-69 ) has

many features of special value, among
which are the following:

 The lathe centers remain in

alignment and the center holes
in the work are not distorted.

 The alignment of the lathe

need not be disturbed, thus
saving considerable time and
effort.

 Taper boring can be

accomplished as easily as taper
turning.

 A much wider range is possible

than by the offset method. For
example, to machine a 3/4-
inch-per-foot taper on the end
of a bar 4 feet long would
require an offset of 1 1/2
inches, which is beyond the
capabilities of a regular lathe
but can be accomplished by use
of the taper attachment.

Some engine lathes are equipped with a taper attachment as standard equipment and most lathe manufacturers
have a taper attachment available. Taper turning with a taper attachment, although generally limited to a taper of 3
inches per foot and to a set length of 12 to 24 inches, affords the most accurate means for turning or boring tapers.
The taper can be set directly on the taper attachment in inches per foot; on some attachments, the taper can be set
in degrees as well.

Ordinarily, when the lathe centers are in line, the work is turned straight, because as the carriage feeds along, the
tool is always the same distance from the centerline. The purpose of the taper attachment is to make it possible to
keep the lathe centers in line, but by freeing the cross slide and then guiding it (and the tool bit) gradually away from
the centerline, a taper can be cut or, by guiding it gradually nearer the centerline (Figure 7-70), a taper hole can be
bored.

A plain taper attachment for the lathe is

illustrated in Figure 7-69. A bed bracket
attaches to the lathe bed and keeps the
angle plate from moving to the left or
the right. The carriage bracket moves
along the underside of the angle plate
in a dovetail and keeps the angle plate
from moving in or out on the bed
bracket. The taper to be cut is set by
placing the guide bar, which clamps to
the angle plate, at an angle to the ways
of the lathe bed. Graduations on one or
both ends of the guide bar are used to
make this adjustment. A sliding block
which rides on a dovetail on the upper
surface of the guide bar is secured
during the machining operation to the
cross slide bar of the carriage, with the
cross feed screw of the carriage being
disconnected. Therefore, as the
carriage is traversed during the feeding
operation, the cross slide bar follows
the guide bar, moving at the
predetermined angle from the ways of
the bed to cut the taper. It is not
necessary to remove the taper attachment when straight turning is desired. The guide bar can be set parallel to the
ways, or the clamp handle can be released permitting the sliding block to move without affecting the cross slide bar,
and the cross feed screw can be reengaged to permit power cross feed and control of the cross slide from the apron
of the carriage.

Modern lathes often use a telescopic taper attachment. This attachment allows for using the cross feed, and set up is
a bit faster than using a standard taper attachment. To use the telescopic attachment, first set the tool bit for the
required diameter of the work and engage the attachment by tightening the binding screws, the location and number
of which depend upon the design of the attachment. The purpose of the binding screws is to bind the cross slide so it
may be moved only by turning the cross feed handle, or, when loosened, to free the cross slide for use with the taper
attachment. To change back to straight turning with the telescopic attachment, it is necessary only to loosen the
binding screws.

When cutting a taper using the taper attachment, the direction of feed should be from the intended small diameter
toward the intended large diameter. Cutting in this manner, the depth of cut will decrease as the tool bit passes along
the workpiece surface and will assist the operator in preventing possible damage to the tool bit, workpiece, and lathe
by forcing too deep a cut.
The length of the taper the guide bar will allow is usually not over 12 to 24 inches, depending on the size of the lathe.
It is possible to machine a taper longer than the guide bar allows by moving the attachment after a portion of the
desired taper length has been machined; then the remainder of the taper can be cut. However, this operation
requires experience.

If a plain standard taper attachment is being used, remove the binding screw in the cross slide and set the compound
rest perpendicular to the ways. Use the compound rest graduated collar for depth adjustments.

When using the taper attachment, there may be a certain amount of "lost motion" (backlash) which must be
eliminated or serious problems will result. In every slide and every freely revolving screw there is a certain amount of
lost motion which is very noticeable if the parts are worn. Care must be taken to remove lost motion before
proceeding to cut or the workpiece will be turned or bored straight for a short distance before the taper attachment
begins to work. To take up lost motion when turning tapers, run the carriage back toward the dead center as far as
possible, then feed forward by hand to the end of the workpiece where the power feed is engaged to finish the cut.
This procedure must be repeated for every cut.

The best way to bore a taper with a lathe is to use the taper attachment. Backlash must be removed when tapers are
being bored with the taper attachment, otherwise the hole will be bored straight for a distance before the taper
starts. Two important factors to consider: the boring tool must be set exactly on center with the workpiece axis, and
it must be small enough in size to pass through the hole without rubbing at the small diameter. A violation of either
of these factors will result in a poorly formed, inaccurate taper or damage to the tool and workpiece. The clearance
of the cutter bit shank and boring tool bar must be determined for the smaller diameter of the taper. Taper boring is
accomplished in the same manner as taper turning.

To set up the lathe attachment for turning a taper, the proper TPF must be calculated and the taper attachment set-
over must be checked with a dial indicator prior to cutting. Calculate the taper per foot by using the formula:

TPF = taper per foot,

D = large diameter (in inches),

d = small diameter (in inches),

L = length of taper

After the TPF is determined, the approximate angle can be set on the graduated TPF scale of the taper attachment.
Use a dial indicator and a test bar to set up for the exact taper. Check the taper in the same manner as cutting the
taper by allowing for backlash and moving the dial indicator along the test bar from the tailstock end of the head
stock end. Check the TPI by using the thread-chasing dial, or using layout lines of 1-inch size, and multiply by 12 to
check the TPF. Make any adjustments needed, set up the work to be tapered, and take a trial cut. After checking the
trial cut and making final adjustments, continue to cut the taper to required dimensions as in straight turning. Some
lathes are set up in metric measurement instead of inch measurement. The taper attachment has a scale graduated
in degrees, and the guide bar can be set over for the angle of the desired taper. If the angle of the taper is not given,
use the following formula to determine the amount of the guide bar set over:

Guide Bar Set Over (in millimeters) =

D = large diameter of taper (mm)

d = small diameter of taper (mm)

I = length of taper (mm)

L = length of guide bar (mm)

Reference lines must be marked on the guide bar an equal distance from the center for best results.
A metric dial indicator can be used to measure the guide bar set over, or the values can be changed to inch values
and an inch dial indicator used.

Checking Tapers for Accuracy

Tapers must be checked for uniformity after cutting a trial cut. Lay a good straight edge along the length of the taper
and look for any deviation of the angle or surface. Deviation is caused by backlash or a lathe with loose or worn
parts. A bored taper may be checked with a plug gage (Figure 7-71) by marking the gage with chalk or Prussian blue
pigment. Insert the gage into the taper and turn it one revolution. If the marking on the gage has been rubbed
evenly, the angle of taper is correct. The angle of taper must be increased when there is not enough contact at the
small end of the plug gage, and it must be decreased when there is not enough contact at the large end of the gage.
After the correct taper has been obtained but the gage does not enter the workpiece far enough, additional cuts
must be taken to increase the diameter of the bore.

An external taper may be checked with a ring gage (Figure 7-71). This is achieved by the same method as for checking
internal tapers, except that the workpiece will be marked with the chalk or Prussian blue pigment rather than the
gage. Also, the angle of taper must be decreased when there is not enough contact at the small end of the ring gage
and it must be increased when there is not enough contact at the large end of the gage. If no gage is available, the
workpiece should be tested in the hole it is to fit. When even contact has been obtained, but the tapered portion
does not enter the gage or hole far enough, the diameter of the piece is too large and must be decreased by
additional depth of cut

Another good method of checking external tapers is to scribe lines on the workpiece 1 inch apart (Figure 7-72); then,
take measurements with an outside micrometer. Subtracting the small reading from the large reading will give the
taper per inch.
Duplicating a Tapered Piece

When the taper on a piece of work is to be duplicated and the original piece is available, it may be placed between
centers on the lathe and checked with a dial indicator mounted in the tool post.. When the setting is correct, the dial
indicator reading will remain constant when moved along the length of taper.

This same method can be used on workpieces without centers provided one end of the workpiece can be mounted
and held securely on center in the headstock of the lathe. For example, a lathe center could be mounted in the lathe
spindle by use of the spindle sleeve, or a partially tapered workpiece could be held by the nontapered portion
mounted in a collet or a chuck. Using either of these two methods of holding the work, the operator could use only
the compound rest or the taper attachment for determining and machining the tapers.

Standard Tapers

There are various standard tapers in commercial use, the most common ones being the Morse tapers, the Brown and
Sharpe tapers, the American Standard Machine tapers, the Jarno tapers, and the Standard taper pins.

Morse tapers are used on a variety of tool shanks, and exclusively on the shanks of twist drills. The taper for different
numbers of Morse tapers is slightly different, but is approximately 5/8 inch per foot in most cases. Dimensions for
Morse tapers are given in Machinist Table 7-4 in Appendix A.

Brown and Sharpe tapers are used for taper shanks on tools such as end mills and reamers. The taper is
approximately � inch per foot for all sizes except for taper No 10, where the taper is 0.5161 inch per foot.

The American Standard machine tapers are composed of a self-holding series and a steep taper series. The self-
holding taper series consists of 22 sizes which are given in Machinist Table 7-5 in Appendix A. The name "self-
holding" has been applied where the angle of the taper is only 2� or 3� and the shank of the tool is so firmly
seated in its socket that there is considerable frictional resistance to any force tending to. turn or rotate the tool in
the holder. The self-holding tapers are composed of selected tapers from the Morse, the Brown and Sharpe, and the
�-inch-per foot machine taper series. The smaller sizes of self-holding tapered shanks are provided with a tang to
drive the cutting tool. Larger sizes employ a tang drive with the shank held by a key, or a key drive with the shank
held with a draw bolt. The steep machine tapers consist of a preferred series and an intermediate series as given
in Machinist Table 7-6 in Appendix A. A steep taper is defined as a taper having an angle large enough to ensure the
easy or self-releasing feature. Steep tapers have a 3 �-inch taper per foot and are used mainly for aligning milling
machine arbors and spindles, and on some lathe spindles and their accessories.

The Jarno taper is based on such simple formulas that practically no calculations are required when the number of
taper is known. The taper per foot of all Jarno tapers is 0.600 inch per foot. The diameter at the large end is as many
eighths, the diameter at the small end is as many tenths, and the length as many half-inches as indicated by the
number of the taper. For example: A No 7 Jarno taper is 7/8 inch in diameter at the large end; 7/10 or 0.7 inch in
diameter at the small end; and 7/2, or 3 � inches long. Therefore, formulas for these dimensions would read:

The Jarno taper is used on various machine tools, especially profiling machines and die-sinking machines. It has also
been used for the headstock and tailstock spindles on some lathes.

The Standard taper pins are used for positioning and holding parts together and have a �-inch taper per foot.
Standard sizes in these pins range from No 7/0 to No 10 and are given in Machinist Table 7-7 in Appendix A. The
tapered holes used in conjunction with the tapered pins utilize the processes of step-drilling and taper reaming.
To preserve the accuracy and efficiency of tapers (shanks and holes), they must be kept free from dirt, chips, nicks, or
burrs. The most important thing in regard to tapers is to keep them clean. The next most important thing is to
remove all oil by wiping the tapered surfaces with a soft, dry cloth before use, because an oily taper will not hold.

SCREW THREAD CUTTING

Screw threads are cut with the lathe for accuracy and for versatility. Both inch and metric screw threads can be cut
using the lathe. A thread is a uniform helical groove cut inside of a cylindrical workpiece, or on the outside of a tube
or shaft. Cutting threads by using the lathe requires a thorough knowledge of the different principles of threads and
procedures of cutting. Hand coordination, lathe mechanisms, and cutting tool angles are all interrelated during the
thread cutting process. Before attempting to cut threads on the lathe a machine operator must have a thorough
knowledge of the principles, terminology and uses of threads.

Screw Thread Terminology

The common terms and definitions below are used in screw thread work and will be used in discussing threads and
thread cutting.

 External or male thread is a thread on the outside of a cylinder or cone.

 Internal or female thread is a thread on the inside of a hollow cylinder or bore.

 Pitch is the distance from a given point on one thread to a similar point on a thread next to it, measured
parallel to the axis of the cylinder. The pitch in inches is equal to one divided by the number of threads per
inch.

 Lead is the distance a screw thread advances axially in one complete revolution. On a single-thread screw,
the lead is equal to the pitch. On a double-thread screw, the lead is equal to twice the pitch, and on a triple-
thread screw, the lead is equal to three times the pitch (Figure 7-74).

 Crest (also called "flat") is the top or outer surface of the thread joining the two sides.

 Root is the bottom or inner surface joining the sides of two adjacent threads.

 Side is the surface which connects the crest and the root (also called the flank).

 Angle of the thread is the angle formed by the intersection of the two sides of the threaded groove.
 Depth is the distance between the crest and root of a thread, measured perpendicular to the axis.

 Major diameter is the largest diameter of a screw thread.

 Minor diameter is the smallest diameter of a screw thread.

 Pitch diameter is the diameter of an imaginary cylinder formed where the width of the groove is equal to
one-half of the pitch. This is the critical dimension of threading as the fit of the thread is determined by the
pitch diameter (Not used for metric threads).

 Threads per inch is the number of threads per inch may be counted by placing a rule against the threaded
parts and counting the number of pitches in 1 inch. A second method is to use the screw pitch gage. This
method is especially suitable for checking the finer pitches of screw threads.

 A single thread is a thread made by cutting one single groove around a rod or inside a hole. Most hardware
made, such as nuts and bolts, has single threads. Double threads have two grooves cut around the cylinder.
There can be two, three, or four threads cut around the outside or inside of a cylinder. These types of special
threads are sometimes called multiple threads.

 A right-hand thread is a thread in which the bolt or nut must be turned to the right (clockwise) to tighten.

 A left hand thread is a thread in which the bolt or nut must turn to the left (counterclockwise) to tighten.

 Thread fit is the way a bolt and nut fit together as to being too loose or too tight.

 Metric threads are threads that are measured in metric measurement instead of inch measurement.

Screw Thread Forms

The most commonly used screw thread forms

are detailed in the following paragraphs. One of
the major problems in industry is the lack of a
standard form for fastening devices. The screw
thread forms that follow attempt to solve this
problem; however, there is still more than one
standard form being used in each industrial
nation. The International Organization for
Standardization (IS0) met in 1975 and drew up a
standard metric measurement for screw
threads, the new IS0 Metric thread Standard
(previously known as the Optimum Metric
Fastener System). Other thread forms are still in
general use today, including the American
(National) screw thread form, the square thread,
the Acme thread, the Brown and Sharpe 29�
worm screw thread, the British Standard
Whitworth thread, the Unified thread, and
different pipe threads. All of these threads can
be cut by using the lathe.

 The IS0 Metric thread standard is a

simple thread system that has threaded sizes ranging in diameter from 1.6 mm to 100 mm (see Machinist
Table 7-8 in Appendix A). These metric threads are identified by the capital M, the nominal diameter, and the
pitch. For example, a metric thread with an outside diameter of 5 mm and a pitch of 0.8 mm would be given
as M 5 x 0.8. The IS0 metric thread standard simplifies thread design, provides for good strong threads, and
requires a smaller inventory of screw fasteners than used by other thread forms. This IS0 Metric thread has a
 60� included angle and a crest that is 1.25 times the pitch (which is similar to the National thread form).
The depth of thread is 0.6134 times the pitch, and the flat on the root of the thread is wider than the crest.
The root of the ISO Metric thread is 0.250 times the pitch (Machinist Table 7-9).

 The American (National) screw thread form is divided into four series, the National Coarse (NC), National Fine
(NF), National Special (NS), and National Pipe threads (NPT). 11 series of this thread form have the same
shape and proportions. This thread has a 60� included angle. The root and crest are 0.125 times the pitch.
This thread form is widely used in industrial applications for fabrication and easy assembly and construction
of machine parts. Table 7-9 in Appendix A gives the different values for this thread form.

 The British Standard Whitworth thread form thread has a 55� thread form in the V-shape. It has rounded
crests and roots.

 The Unified thread form is now used instead of the American (National) thread form. It was designed for
interchangeability between manufacturing units in the United States, Canada, and Great Britain. This thread
is a combination of the American (National) screw thread form and the British Whitworth screw thread
forms. The thread has a 60� angle with a rounded root, while the crest can be rounded or flat. (In the
United States, a flat crest is preferred.) The internal thread of the unified form is like the American (National)
thread form but is not cut as deep, leaving a crest of one-fourth the pitch instead of one-eighth the pitch.
The coarse thread series of the unified system is designated UNC, while the fine thread series is designated
UNF. (See Machinist Table 7-9 in Appendix A for thread form and values.

 The American National 29� Acme was designed to replace the standard square thread, which is difficult to
machine using normal taps and machine dies. This thread is a power transmitting type of thread for use in
jacks, vises, and feed screws. Machinist Table 7-9 lists the values for Acme threads.

The Brown and Sharpe 29� worm screw thread uses a 29� angle, similar to the Acme thread. The depth is greater
and the widths of the crest and root are different (Machinist Table 7-9 in Appendix A). This is a special thread used to
mesh with worm gears and to transmit motion between two shafts at right angles to each other that are on separate
planes. This thread has a self-locking feature making it useful for winches and steering mechanisms.

 The square screw thread is a power transmitting thread that is being replaced by the Acme thread. Some
vises and lead screws may still be equipped with square threads. Contact areas between the threads are
small, causing screws to resist wedging, and friction between the parts is minimal (Machinist Table 7-9 in
Appendix A).

 The spark plug thread (international metric thread type) is a special thread used extensively in Europe, but
seen only on some spark plugs in the United States. It has an included angle of 60� with a crest and root
that are 0.125 times the depth.

 Different types of pipe thread forms are in use that have generally the same characteristics but different fits.
Consult the Machinery's Handbook or a similar reference for this type of thread.

THREAD FIT AND CLASSIFICATIONS

The Unified and American (National) thread forms designate classifications for fit to ensure that mated threaded
parts fit to the tolerances specified. The unified screw thread form specifies several classes of threads which are
Classes 1A, 2A, and 3A for screws or external threaded parts, and 1B, 2B, and 3B for nuts or internal threaded parts.
Classes 1 A and 1 B are for a loose fit where quick assembly and rapid production are important and shake or play is
not objectionable. Classes 2A and 2B provide a small amount of play to prevent galling and seizure in assembly and
use, and sufficient clearance for some plating. Classes 2A and 2B are recommended for standard practice in making
commercial screws, bolts, and nuts. Classes 3A and 3B have no allowance and 75 percent of the tolerance of Classes
2A and 2B A screw and nut in this class may vary from a fit having no play to one with a small amount of play. Only
high grade products are held to Class 3 specifications.

Four distinct classes of screw thread fits between mating threads (as between bolt and nut) have been designated for
the American (National) screw thread form. Fit is defined as "the relation between two mating parts with reference
to ease of assembly. " These four fits are produced by the application of tolerances which are listed in the standards.
The four fits are described as follows:

 Class 1 fit is recommended only for screw thread work where clearance between mating parts is essential for
rapid assembly and where shake or play is not objectionable.

 Class 2 fit represents a high quality of thread product and is recommended for the great bulk of
interchangeable screw thread work.

 Class 3 fit represents an exceptionally high quality of commercially threaded product and is recommended
only in cases where the high cost of precision tools and continual checking are warranted.

 Class 4 fit is intended to meet very unusual requirements more exacting than those for which Class 3 is
intended. It is a selective fit if initial assembly by hand is required. It is not, as yet, adaptable to quantity
production.

Thread Designations

In general, screw thread designations give the screw number (or diameter) first, then the thread per inch. Next is the
thread series containing the initial letter of the series, NC (National Coarse), UNF (Unified Fine), NS (National Special),
and so forth, followed by the class of fit. If a thread is left-hand, the letters LH follow the fit. An example of
designations is as follows:

Two samples and explanations of thread designations are as follows:

 No 12 (0.216) - 24 NC-3. This is a number 12 (0.216-inch diameter) thread, 24 National Coarse threads per
inch, and Class 3 ways of designating the fit between parts, including tolerance grades, tolerance positions,
and tolerance classes. A simpler fit.

 1/4-28 UNF-2A LH. This is a l/4-inch diameter thread, 28 Unified Fine threads per inch, Class 2A fit, and left-
hand thread.

Metric Thread Fit and Tolerance

The older metric screw thread system has over one hundred different thread sizes and several ways of designating
the fit between parts, including tolerance grades, tolerance positions, and tolerance classes. A simple system was
devised with the latest ISO Metric thread standard that uses one internal fit and two external fit designations to
designate the tolerance (class) of fit. The symbol 6H is used to designate the fit for an internal thread (only the one
symbol is used). The two symbols 6g and 5g6g are used to designate the fit for an external thread, 6g being used for
general purpose threads and Sg6g used to designate a close fit. A fit between a pair of threaded parts is indicated by
the internal thread (nut) tolerance fit designation followed by the external thread (bolt) tolerance fit designation with
the two separated by a stroke. An example is M 5 x 0.8-Sg6g/6H, where the nominal or major diameter is 5 mm, the
pitch is 0.8 mm, and a close fit is intended for the bolt and nut. Additional information on ISO metric threads and
specific fits can be found in any updated engineer's handbook or machinist's handbook.

THREAD CUTTING TOOL BITS

Cutting V-threads with a 60 degrees thread angle is the most common thread cutting operation done on a lathe. V-
threads, with the 60 degree angle, are used for metric thread cutting and for American (National) threads and Unified
threads. To properly cut V-shaped threads, the single point tool bit must be ground for the exact shape of the thread
form, to include the root of the thread (Figure 7-75).

For metric and American (National) thread forms, a flat should be ground at the point of the tool bit (Figure 7-76),
perpendicular to the center line of the 600 thread angle. See the thread form table for the appropriate thread to
determine the width of the Sat. For unified thread forms, the tip of the tool bit should be ground with a radius
formed to fit the size of the root of the thread. Internal unified threads have a flat on the tip of the tool bit. In all
threads listed above, the tool bit should be ground with enough side relief angle and enough front clearance angle
(Figure 7-76). Figure 7-77 illustrates the correct steps involved in grinding a thread-cutting tool bit.

For Acme and 29� worm screw threads, the cutter bit must be ground to form a point angle of 29�. Side
clearances must be sufficient to prevent rubbing on threads of steep pitch. The end of the bit is then ground to a flat
which agrees with the width of the root for the specific pitch being cut. Thread-cutting tool gages (Figure 7-78) are
available to simplify the procedure and make computations unnecessary.

To cut square threads, a special thread-cutter bit is

required. Before the square thread-cutter bit can be
ground, it is necessary to compute the helix angle of
the thread to be cut (Figure 7-79). Compute the
helix angle by drawing a line equal in length to the
thread circumference at its minor diameter (this is
accomplished by multiplying the minor diameter by
3.1416 [pi]). Next, draw a line perpendicular to and
at one end of the first line, equal in length to the
lead of the thread. If the screw is to have a single
thread, the lead will be equal to the pitch. Connect
the ends of the angle so formed to obtain the helix
angle.

The tool bit should be ground to the helix angle. The

clearance angles for the sides should be within the
helix angle. Note that the sides are also ground in
toward the shank to provide additional clearance.

The end of the tool should be ground flat, the flat

being equal to one-half the pitch of the thread to
produce equal flats and spaces on the threaded
part.
When positioning the thread-cutter bit for use, place it exactly on line horizontally with the axis of the workpiece.
This is especially important for thread-cutter bits since a slight variation in the vertical position of the bit will change
the thread angle being cut.

The thread-cutter bit must be positioned so that the centerline of the thread angle ground on the bit is exactly
perpendicular to the axis of the workpiece. The easiest way to make this alignment is by use of a center gage. The
center gage will
permit checking the
point angle at the
same time as the
alignment is being
effected. The center
gage is placed against
the workpiece and the
cutter bit is adjusted
on the tool post so
that its point fits
snugly in the 60�
angle notch of the
center gage (Figure 7-80).

In cutting threads on a lathe, the pitch of

the thread or number of threads per inch
obtained is determined by the speed ratio
of the headstock spindle and the lead
screw which drives the carriage. Lathes
equipped for thread cutting have gear
arrangements for varying the speed of the
lead screw. Modern lathes have a quick-
change gearbox for varying the lead screw
to spindle ratio so that the operator need
only follow the instructions on the direction
plates of the lathe to set the proper feed to
produce the desired number of threads per
inch. Once set to a specific number of
threads per inch, the spindle speed can be
varied depending upon the material being
cut and the size of the workpiece without
affecting the threads per inch.

The carriage is connected to the lead screw

of the lathe for threading operations by
engaging the half nut on the carriage apron
with the lead screw. A control is available to
reverse the direction of the lead screw for
left or right-hand threading as desired. Be sure the
lead screw turns in the proper direction. Feed the
cutter bit from right to left to produce a right-hand
thread. Feed the cutter bit from left to right to
produce a left-hand thread.

Direction of feed. For cutting standard 60� right-

hand threads of the sharp V-type, such as the metric
form, the American (National) form, and the Unified form, the tool bit should be moved in at an angle of 29� to the
right (Figure 7-81). (Set the angle at 29� to the left for left-hand threads). Cutting threads with the compound rest at
this angle allows for the left side of the tool bit to do most of the cutting, thus relieving some strain and producing a
free curling chip. The direction is controlled by setting the compound rest at the 29� angle before adjusting the
cutter bit perpendicular to the workpiece axis. The depth of cut is then controlled by the compound rest feed handle.

For Acme and 29� worm threads, the compound rest is set at one-half of the included angle (14 1/2�) and is fed in
with the compound rest. For square threads, the cutter bit is fed into the workpiece at an angle perpendicular to the
workpiece axis.

THREAD CUTTING OPERATIONS

Before cutting threads, turn down the workpiece to the major diameter of the thread to be cut and chamfer the end.
Engineering and machinist's handbooks have special tables listing the recommended major and minor diameters for
all thread forms. These tables list a minimum and a maximum major diameter for the external threads, and a
minimum and maximum minor diameter for internal threads. Machinist Table 7-10 in Appendix A lists the most
common screw thread sizes. The difference between the maximum and minimum major diameters varies with
different sizes of threads. Coarse threads have a larger difference between the two than fine threads. It is common
practice, when machining threads on the lathe, to turn the outside diameter down to the maximum major diameter
instead of the minimum major diameter, thus allowing for any error.

The workpiece may be set up in a chuck, in a collet, or between centers. If a long thread is to be cut, a steady rest or
other support must be used to help decrease the chance of bending the workpiece. Lathe speed is set for the
recommended threading speed (Machinist Lathe Table 7-2 in Appendix A).

To cut threads, move the threading tool bit into contact with the work and zero the compound rest dial. The
threading tool bit must be set at the right end of the work; then, move the tool bit in the first depth of cut by using
the graduated collar of the compound rest. Position the carriage half nut lever to engage the half nut to the lead
screw in order to start the threading operation. The first cut should be a scratch cut of no more than 0.003 inch so
the pitch can be checked. Engaging the half nut with the lead screw causes the carriage to move as the lead screw
revolves. Cut the thread by making a series of cuts in which the threading tool follows the original groove for each
cut. Use the thread chasing dial, Figure 7-82, to determine when to engage the half nut so that the threading tool will
track properly. The dial is attached to the carriage and is driven by means of the lead screw. Follow the directions of
the thread chasing dial, Figure 7-83, to determine when to engage the half nut lever.
After making the first pass check for proper pitch of threads by using one of the three methods in Figure 7-84. After
each pass of the threading tool bit, the operator must move the threading tool bit out of the threaded groove by
backing out the compound rest handle, taking note of the setting. Traverse the carriage back to the start of the
thread and move the compound rest dial back to the original setting plus the new depth of cut. At the end of each
cut, the half nut lever is usually disengaged and the carriage returned by hand. (The cross slide dial can also be used
to move the tool bit in and out, depending on the preference of the operator.)

After cutting the first depth of thread, check for the proper pitch of threads by using one of the three methods in
Figure 7-84. If the thread pitch is correct as set in the quick-change gearbox, continue to cut the thread to the
required depth. This is determined by measuring the pitch diameter and checking the reference table for-the proper
pitch diameter limits for the desired fit.

Some lathes are equipped with a thread chasing stop bolted to the carriage which can be set to regulate the depth of
cut for each traverse of the cutter bit or can be set to regulate the total depth of cut of the thread.

When the thread is cut the end must be finished in some way. The most common means of finishing the end is with a
specially ground or 45 degree angle chanifer cutting bit. To produce a rounded end, a cutter bit with the desired
shape should be specially ground for that purpose.

Metric Thread Cutting Operations

Metric threads, are cut one of two ways by using the lathe, designed and equipped for metric measurement or by
using a standard inch lathe and converting its operation to cut metric threads. A metric measurement lathe has a
quick-change gear box used to set the proper screw pitch in millimeters. An inch-designed lathe must be converted to
cut metric threads by switching gears in the lathe headstock according to the directions supplied with each lathe.

Most lathes come equipped with a set of changeable gears for cutting different, or nonstandard screw threads.
Follow the directions in the lathe operator manual for setting the proper metric pitch. (A metric data plate may be
attached to the lathe headstock.) Most lathes have the capability of quickly attaching these change gears over the
existing gears then realigning the gearing. One change gear in needed for the lead screw gear and one for the
spindle, or drive gear.

The metric thread diameter and pitch can be easily measured with a metric measuring tool. If there are no metric
measuring tools available, the pitch and diameter must be converted from millimeters to inch measurement, and
then a inch micrometer and measuring tools can be used to determine the proper pitch and diameter. Millimeters
may be converted to inch measurement either by dividing millimeters by 25.4 inches or multiplying by 0.03937
inches.

For example, a thread with a designation M20 x 2.5 6g/6h is read as follows: the M designates the thread is metric.
The 20 designates the major diameter in millimeters. The 2.5 designates the linear pitch in millimeters. The 6g/6h
designates that a general purpose fit between nut and bolt is intended. Therefore, to machine this metric thread on a
inch designed lathe, convert the outside diameter in millimeters to a decimal fraction of an inch and machine the
major diameter to the desired diameter measurement. Convert the linear pitch in millimeters, to threads per inch by
dividing the linear pitch of 2.5 by 25.4 to get the threads per inch (10.16 TPI).

Now. a 8-13 TPI thread micrometer can be used to measure the pitch diameter for this metric thread.

To sum up how to convert metric threads to inch measurement:

 Convert major diameter from millimeters to inch measure.

  Convert pitch and pitch diameter to inch measure.

 Set quick change gears according to instructions.

Set up the lathe for thread cutting as in the preceding paragraphs on screw thread cutting. Take a light trial cut and
check that the threads are of the correct pitch using a metric screw pitch gage. At the end of this trial cut, and any cut
when metric threading, turn off the lathe and back out the tool bit from the workpiece without disengaging the half-
nut-lever. Never disengage the lever until the metric thread is cut to the proper pitch diameter, or the tool bit will
have to be realigned and set for chasing into the thread.

After backing the tool bit out from the workpiece, traverse the tool bit back to the starting point by reversing the
lathe spindle direction while leaving the half-nut lever engaged. If the correct pitch is being cut, continue to machine
the thread to the desired depth.

NOTE: If the tool bit needs to be realigned and chased into the thread due to disengagement, of the half-nut lever or
having to remove the piece and start again, then the lathe must be reset for threading. Start the lathe, with the tool
bit clear of the workpiece engage the lever. Allow the carriage to travel until the tool bit is opposite any portion of
the unfinished thread; and then turn off the lathe, leaving the engaged. Now the tool bit can be set back into a
thread groove by advancing the cross slide and reference. Restart the lathe, and the tool bit should follow the groove
that was previously cut, as long as the half-nut lever stays engaged.

TAPERED SCREW THREADS

Tapered screw threads or pipe threads can be cut on the lathe by setting the tailstock over or by using a taper
attachment. Refer to the references for taper per inch and nominal measurements of tapered thread forms. When
cutting a tapered thread, the tool bit should be set at right angles to the axis of the work. Do not set the tool bit at a
right angle to the taper of the thread. Check the thread tool bit carefully for clearances before cutting since the bit
will not be entering the work at right angles to the tapered workpiece surface.

MEASURING EXTERNAL V-SHAPED SCREW THREADS

The fit of the thread is determined by its pitch diameter. The pitch diameter is the diameter of the thread at an
imaginary point on the thread where the width of the space and the width of the thread are equal. The fact that the
mating parts bear on this point or angle of the thread, and not on the top of it, makes the pitch diameter an
important dimension to use in measuring screw threads.

The thread micrometer (Figure 7-85) is an instrument used to gage the thread on the pitch diameter. The anvil is V-
Shaped to fit over the V-thread. The spindle, or movable point, is cone-shaped (pointed to a V) to fit between the
threads. Since the anvil and spindle both contact the sides of the threads, the pitch diameter is gaged and the
reading is given on the sleeve and spindle where it can be read by the operator.

Thread micrometers are marked on the frame to

specify the pitch diameters which the micrometer is
used to measure. One will be marked, for instance, to
measure from 8 to 13 threads per inch, while others
are marked 14 to 20, 22 to 30, or 32 to 40; metric
thread micrometers are also available in different sizes.

The procedure in checking the thread is first to select

the proper micrometer, then calculate or select from a
table of threads the correct pitch diameter of the
screw. Lastly, fit the thread into the micrometer and
take the reading.

The 3-wire method is another method of measuring

the pitch diameter for American National (60 degree)
and Unified threads. It is considered the "best" method for extremely accurate measurement. Appendix A shows
three wires of correct diameter placed in threads with the micrometer measuring over them. The pitch diameter can
be found by subtracting the wire constant from the measured distance over the wires. It can be readily seen that this
method is dependent on the use of the "'best'" wire for the pitch of the thread. The "best" wire is the size of wire
which touches the thread at the middle of the sloping sides. in other words, at the pitch diameter. A formula by
which the proper size wire may be found is as follows: Divide the constant 0.57735 by the number of threads per inch
to cut. If. for example, 8 threads per inch have been cut, we would calculate 0.57735 8 = 0.072. The diameter of wire
to use for measuring an 8-pitch thread is 0.072.

The wires used in the three-wire method should be hardened and lapped steel wires. they, should be three times as
accurate as the accuracy desired in measurement of the threads. The Bureau of Standards has specified an accuracy
of 0.0002 inch. The suggested procedure for measuring threads is as follows:

After the three wires of equal diameter have been selected by using the above formula, they are positioned in the
thread grooves as shown in Appendix A. The anvil and spindle of an ordinary micrometer are then placed against the
three wires and the reading is taken. To determine what the reading of the micrometer should be if a thread is the
correct finish size. use the following formula (for measuring Unified National Coarse threads): add three times the
diameter of the wire to the diameter of the screw; from the sum, subtract the quotient obtained by dividing the
constant 1.5155 by the number of threads per inch. Written concisely, the formula is:

Where m=micrometer measurement over

wires,

D =diameter of the thread,

n =number of threads per inch,

W =diameter of wire used

Example: Determine m (measurement over wires) for 1/2 inch, 12-pitch UNC thread. We would proceed to solve as
follows:

where =0.04811 inch

W

D =0.500 inch

n =12

Then m=

m =(0.500 + 0.14433) - 0.1263

m =0.51803 inch (micrometer measurement)

When measuring a Unified National Fine thread, the same method and formula are used. Too much pressure should
not be applied when measuring over wires.

Metric threads can also be checked by using the three-wire method by using different numerical values in the
formula. Three-wire threads of metric dimensions must have a 60� angle for this method.

M =PD+ CPD = M-C

 M =measurement over the wires

PD=pitch diameter

C =N constant (This is found in Machinist Table 7-11)

The "best" wire size can be found by converting from inch to metric, or by using Machinist Table 7-11.

An optical comparator must be used to check the threads if the tolerance desired is less than 0.001 inch (0.02 mm).
This type of thread measurement is normally used in industrial shops doing production work.

CUTTING INTERNAL THREADS

Internal threads are cut into nuts and castings in the same general manner as external threads. If a hand tap is not
available to cut the internal threads, they must be machined on the lathe.

An internal threading operation will usually follow a boring and drilling operation, thus the machine operator must
know drilling and boring procedures before attempting to cut internal threads. The same holder used for boring can
be used to hold the tool bit for cutting internal threads. Lathe speed is the same as the speed for external thread
cutting.

To prevent rubbing, the clearance of the cutter bit shank and boring tool bar must be greater for threading than for
straight boring because of the necessity of moving the bit clear of the threads when returning the bit to the right
after each cut.

The compound rest should be set at a 29� angle to the saddle so that the cutter bit will feed after each cut toward
the operator and to his left.

Although the setup shown in Figure 7-86 would be impractical on extremely large lathes, it allows a degree of safety
on common sized machines by having the compound ball crank positioned away from any work holding device that
would be in use on the lathe, eliminating the possibility of the operator's hands or the compound rest contacting the
revolving spindle and work holding devices.

Cutting 60� left-hand threads. A left-hand thread is used for certain applications where a right-hand thread would
not be practicable, such as on the left side of a grinder where the nut may loosen due to the rotation of the spindle.
Left-hand threads are cut in the same manner as right hand threads, with a few changes. Set the feed direction lever
so that the carriage feeds to the right, which will mean that the lead screw revolves opposite the direction used for
right-hand threading. Set the compound rest 29� to the left of perpendicular. Cut a groove at the left end of the
threaded section, thus providing clearance for starting the cutting tool (see Figure 7-87). Cut from left to right until
the proper pitch dimension is achieved.

CUTTING EXTERNAL ACME THREADS

The first step is to grind a threading tool to

conform to the 29� included angle of the thread.
The tool is first ground to a point, with the sides
of the tool forming the 29� included angle
(Figure 7-88). This angle can be checked by
placing the tool in the slot at the right end of the
Acme thread gage.

If a gage is not available, the width of the tool bit

point may be calculated by the formula:

Width of point = 0.3707P - 0.0052 inch

Where P = Number of threads per inch

Be sure to grind this tool with sufficient side clearance so that it will cut. Depending upon the number of threads per
inch to be cut, the point of the tool is ground flat to fit into the slot on the Acme thread gage that is marked with the
number of threads per inch the tool is to cut. The size of the flat on the tool point will vary depending upon the
thread per inch to be machined.

After grinding the tool, set the compound rest to one-half the included angle of the thread (14 1/2�) to the right of
the vertical centerline of the machine (Figure 7-89). Mount the tool in the holder or tool post so that the top of the
tool is on the axis or center line of the workpiece. The tool is set square to the work, using the Acme thread gage.
This thread is cut using the compound feed. The depth to which you feed the compound rest to obtain total thread
depth is determined by the formula given and illustrated in Table 7-9 in Appendix A. The remainder of the Acme
thread-cutting operation is the same as the V-threading operation previously described. The compound rest should
be fed into the work only 0.002 inch to 0.003 inch per cut until the desired depth of thread is obtained.

The formulas used to calculate Acme thread depth are in Machinist Table 7-9. The single wire method can be used to
measure the accuracy of the thread (Figure 7-90). A single wire or pin of the correct diameter is placed in the
threaded groove and measured with a micrometer. The thread is the correct size when the micrometer reading over
the wire is the same as the major diameter of the thread and the wire is placed tightly into the thread groove. The
diameter of the wire to be used can be calculated by using this formula:

Wire diameter = 0.4872 x pitch

Thus, if 6 threads per inch are being cut, the wire size would be:

0.4872 x 1/6 = 0.081 inch

Cutting the 29� worm screw thread (Brown and Sharpe). The tool bit used to cut 29� worm screw threads will be
similar to the Acme threading tool, but slightly longer with a different tip. Use Table 7-9 in Appendix A to calculate
the length of the tool bit and tip width. The cutting is done just like cutting an Acme thread.

CUTTING SQUARE THREADS

Because of their design and strength, square threads are used for vise screws, jackscrews, and other devices where
maximum transmission of power is needed. All surfaces of the square thread form are square with each other, and
the sides are perpendicular to the center axis of the threaded part. The depth, the width of the crest, and root are of
equal dimensions. Because the contact areas are relatively small and do not wedge together, friction between
matching threads is reduced to a minimum. This fact explains why square threads are used for power transmission.

Before the square thread cutting tool can be ground, it is necessary first to determine the helix angle of the thread.
The sides of the tool for cutting the square thread should conform with the helix angle of the thread (Figure 7-79).

For cutting the thread, the cutting edge of the tool should be ground to a width exactly one-half that of the pitch. For
cutting the nut, it should be from 0.001 to 0.003 of an inch larger to permit a free fit of the nut on the screw.

The cutting of the square thread form presents some difficulty. Although it is square, this thread, like any other,
progresses in the form of a helix, and thus assumes a slight twist. Some operators prefer to produce this thread in
two cuts, the first with a narrow tool to the full depth and the second with a tool ground to size. This procedure
relieves cutting pressure on the tool nose and may prevent springing the work. The cutting operation for square
threads differs from cutting threads previously explained in that the compound rest is set parallel to the axis of the
workpiece and feeding is done only with the cross feed. The cross feed is fed only 0.002 inch or 0.003 inch per cut.
The finish depth of the thread is determined by the formula.

Depth = 1/2P

The width of the tool point is determined by this formula also and will depend upon the number of threads per inch
to be machined. It is measured with a micrometer, as square thread gages are not available.

SPECIAL OPERATIONS ON THE LATHE

KNURLING ON THE LATHE

Knurling is a process of impressing a diamond shaped or straight line pattern into the surface of a workpiece by using
specially shaped hardened metal wheels to improve its appearance and to provide a better gripping surface. Straight
knurling is often used to increase the workpiece diameter when a press fit is required between two parts.

Holding Devices for Knurling

The setup for knurling can be made between centers or mounted in a solid chuck. Never attempt to knurl by holding
the work in a rubber or metal collet chuck, since the great pressures of knurling could damage these devices. It is
important to support the work while knurling. If mounting the work between centers, make the center holes as large
as possible to allow for the strongest hold. If using a chuck to hold the work, use the tailstock center to support the
end of the work. If doing a long knurl, use a steady rest to support the work and keep the piece from springing away
from the tool.

Knurling Tools

The knurling tool (Figure 7-10) can be designed differently, but all accomplish the same operation. Two common
types of knurling tools are the knuckle joint and revolving head type of knurling tools. The knuckle joint type is
equipped with a single pair of rollers that revolve with the work as it is being knurled. The revolving head type of tool
is fitted with three pairs of rollers so that the pitch can be changed to a different knurl without having to change the
setup. There are two knurl patterns, diamond and straight.

There are three pitches of rollers, coarse, medium, and fine (Figure 7-91).

The diamond is the most common pattern and the medium pitch is used most often. The coarse pitch is used for
large-diameter work; the fine pitch is used for small-diameter work.

Knurling

The knurling operation is started by determining the location and length of the knurl, and then setting the machine
for knurling. A slow speed is needed with a medium feed. Commonly, the speed is set to 60 to 80 RPM, while the
feed is best from 0.015 to 0.030 inch per revolution of the spindle. The knurling tool must be set in the tool post with
the axis of the knurling head at center height and the face of the knurls parallel with the work surface. Check that the
rollers move freely and are in good cutting condition; then oil the knurling tool cutting wheels where they contact the
workpiece. Bring the cutting wheels (rollers) up to the surface of the work with approximately 1/2 of the face of the
roller in contact with the work.

If the face of the roller is placed in this manner, the initial pressure that is required to start the knurl will be lessened
and the knurl may cut smoother. Apply oil generously over the area to be knurled. Start the lathe while forcing the
knurls into the work about 0.010 inch. As the impression starts to form, engage the carriage feed lever (Figure 7-92).
Observe the knurl for a few revolutions and shut off the machine. Check to see that the knurl is tracking properly, and
that it is not on a "double track" (Figure 7-93).
Reset the tool if needed; otherwise, move the carriage and tool back to the starting point and lightly bring the tool
back into the previously knurled portion. The rollers will align themselves with the knurled impressions. Force the
knurling tool into the work to a depth of about 1/64 inch and simultaneously engage the carriage to feed toward the
headstock. Observe the knurling action and allow the tool to knurl to within 1/32 inch of the desired end of cut, and
disengage the feed. Hand feed to the point where only one-half of the knurling wheel is off the work, change the
feed direction toward the tailstock and force the tool deeper into the work.

Engage the carriage feed and cut back to the starting point. Stop the lathe and check the knurl for completeness.
Never allow the knurling tool to feed entirely off the end of the work, or it could cause damage to the work or lathe
centers. The knurl is complete when the diamond shape ( or straight knurl) is fully developed. Excessive knurling after
the knurl has formed will wear off the full knurl and ruin the work diameter. Move the tool away from the work as
the centers. The knurl is complete when the diamond shape (or work revolves and shut off the lathe. Clean the knurl
with a brush and then remove any burrs with a file.

Special Knurling Precautions

Never stop the carriage while the tool is in contact with the work and the work is still revolving as this will cause wear
rings on the work surface (Figure 7-94). Check the operation to ensure that the knurling tool is not forcing the work
from the center hole. Keep the work and knurling tool well oiled during the operation. Never allow a brush or rag to
come between the rollers and the work or the knurl will be ruined.

DRILLING WITH THE LATHE

Frequently, holes will need to be drilled using the lathe before other internal operations can be completed, such as
boring, reaming, and tapping. Although the lathe is not a drilling machine, time and effort are saved by using the
lathe for drilling operations instead of changing the work to another machine. Before drilling the end of a workpiece
on the lathe, the end to be drilled must be spotted (center-punched) and then center-drilled so that the drill will start
properly and be correctly aligned. The headstock and tailstock spindles should be aligned for all drilling, reaming, and
spindles should be aligned for drilling, reaming, and tapping operations in order to produce a true hole and avoid
damage to the work and the lathe. The purpose for which the hole is to be drilled will determine the proper size drill
to use. That is, the drill size must allow sufficient material for tapping, reaming, and boring if such operations are to
follow.

The correct drilling speed usually seems too fast due to the fact that the chuck, being so much larger than the drill,
influences the operator's judgment. It is therefore advisable to refer to a suitable table to obtain the recommended
drilling speeds for various materials, such as Machinist Table 4-2.

Supporting drills in the tailstock

Methods of supporting the twist drill in the tailstock can vary (Figure 7-95). Straight shank drills are usually held in a
drill chuck, which is placed in the taper socket of the tailstock spindle. Combination drill and countersinks (center
drills), counterbores, reamers, taps, and other small shank cutters can also be supported in this way.
Tapered-shank twist drills may be held directly in the tailstock tapered spindle as long as a good fit exists. If the drill
shank is not the correct size, then a drill socket or sleeve may be used in the tailstock spindle.

A twist drill holder is used to support large twist drills with the tailstock center. The drill is inserted into the holder
and the tailstock center is placed in the center hole which is located at the rear of the drill holder. The holder will rest
on the cross slide or compound rest and must be supported by hand until it is held secure by pressure between the
tailstock and headstock. When using this method, never withdraw or loosen the tailstock spindle while the lathe is
rotating or the workpiece can be thrown out at the operator. Always stop the machine before attempting to
withdraw the twist drill.

Another method of supporting a large twist drill in the tailstock is to fasten a lathe dog to the drill shank and support
the rear of the drill with the tailstock center in the center hole in the tang of the drill.

Supporting Drills in the Headstock

The drill can also be held and rotated in the headstock with the work held stationary against the tailstock. Straight
shank twist drills are supported in the headstock by a drill chuck or collet which is mounted in the headstock spindle.
A universal or independent jaw chuck can also be used to hold and turn twist drills if a headstock drill chuck is not
available. Tapered shank twist drills can be mounted in the headstock by using a special adapter, such as a sleeve
with an internal taper to hold the tapered drill, while the outside of the sleeve is made to fit into the headstock
spindle.

Mounting Work for Drilling

If the work is to be rotated and the twist drill will be fed into the end of the work, the work should be mounted in a
chuck, on a faceplate, or in a collet. The center of the hole to be drilled should be accurately marked and punched as
described for drilling setups.

Always start holes by using a center drill, since this method will be the most accurate and the most efficient. Center-
drill by rotating the spindle at computed drill speed and gently bringing the point of the center drill into the end of
the work until the proper depth is reached.

If the twist drill is to be rotated by the headstock spindle and the workpiece is to be supported by a V-center
mounted in the tailstock, the work should be carefully positioned by hand and the drill moved lightly into contact
with the workpiece before starting the lathe. The workpiece must be well supported during drilling operations to
prevent the work from being thrown from the lathe or rotating with the drill.

Drilling Operations

To start the drilling operation, compute the correct RPM for the drill and set the spindle speed accordingly. Ensure
the tailstock is clamped down on the lathe ways. The feed is controlled by turning the tailstock handwheel. The
graduations on the tailstock spindle are used to determine the depth of cut.

If a large twist drill is used, it should be proceeded by a pilot drill, the diameter of which should be wider than the
larger drills web.

Use a suitable cutting fluid while drilling (Machinist Table 4-3). Always withdraw the drill and brush out the chips
before attempting to check the depth of the hole. If the drill is wobbling and wiggling in the hole, use a tool holder
turned backwards (Figure 7-96) to steady the drill. Always use a drill that is properly ground for the material to be
drilled. Use care when feeding the drill into the work to avoid breaking the drill off in the work. The drill should never
be removed from the work while the spindle is turning because the drill could be pulled off the tailstock spindle and
cause injury or damage.

BORING WITH THE LATHE

Boring is the enlarging and truing of a hole by removing material from internal surfaces with a single-point cutter bit.
On the lathe, boring is accomplished in either of these two methods:

 Mounting the holder and boring tool bar with cutter bit on the tool post and revolving the workpiece.

 Mounting the workpiece in a fixed position to the carriage and revolving the boring tool bar and cutter bit in
a chuck attached to the headstock spindle. (This is a special process and not used in most machine shops).
Mounting Workpiece for Boring

The workpiece may be supported in a chuck or fastened to a faceplate for boring operations depending upon of the
material to be machined. When boring is to be performed on the ends of long stock, the workpiece is mounted in a
chuck and a steady rest is used to support the right end near the cutter bit. Some boring operations require the use
of special chuck-mounted mandrels to hold workpieces that cannot be successfully mounted otherwise.

Purpose for Boring

Boring is necessary in many cases to produce accurate holes. Drilled holes are seldom straight due to imperfections in
the material which cause drills to move out of alignment. Therefore, where accuracy is important, drilled holes are
usually made undersize and then bored or reamed to the proper dimensions. Boring is also useful in truing large
holes in flat material. In this case, the hole is cut undersize using a bandsaw or trepanning tool and is trued to proper
dimensions by boring.

Boring Cutter Bit Setup

The cutter bit used for boring is similar to that used for external turning on the lathe. The bit is usually held in a soft
or semisoft bar called a boring tool bar. The boring tool bar (Figure 7-11) is supported by a cutting tool holder which
fits into the lathe tool post.

Boring tool bars are supplied in several types and sizes for holding different cutter bits. The bit is supported in the
boring tool bar at a 90�, 30�, or 45� angle, depending upon the nature of the workpiece being bored. Most
general boring is accomplished with a 90� cutter bit. The bit is mounted at a 30� or 45� angle to the axis of the
boring tool bar when it is necessary to cut up to the bottom of a hole or finish the side of an internal shoulder. It is
desirable that the boring tool bar be as large as possible without interfering with the walls of the hole. The cutter bit
should not extend far beyond the boring tool bar and the bit securely in the bar, yet not have the shank-end protrude
far from the bar.

The cutter bits used for boring are shaped like left-hand turning and facing cutter bits. Greater attention must be
given to the end clearance angle and the back rake angle because of the curvature of the hole (Figure 7-97).

The boring tool bar should be clamped as close to the holder and tool post as possible considering the depth of
boring to be done. The bar will have a tendency to spring away from the workpiece if the bar overhangs the tool post
too far. If deep boring is to be performed, it will be necessary that the bar be as thick as possible to counteract this
springing tendency.

Straight Boring Operation

The cutter bit is positioned for straight boring operations with its cutting edge set slightly above center. Depending on
the rigidity of the setup, the boring tool will have a tendency to spring downward as pressure is applied to the cutting
edge. By setting the cutter slightly above center, compensation has been made for the downward spring and the
cutter will actually be positioned on the exact center of the workpiece during machining operations (Figure 7-98).
The cutting edge faces forward for most operations so the lathe can turn in its normal counterclockwise direction. If it
becomes necessary to position the cutter bit against the rear wall of the hole for a special operation, a right-hand
turning cutter bit is used and the spindle rotation is reversed.

Position the cutter bit so that the cutting edge is immediately to the right of the workpiece and clears the wall of the
hole by about 1/16 inch. Traverse the carriage by hand, without starting the lathe, to move the cutter bit and boring
tool bar into the hole to the depth of the intended boring and out again to determine whether there is sufficient
clearance to prevent the back of the cutter bit and the boring tool bar from rubbing the inside of the hole. When the
clearance is satisfactory, position the cutter bit to the right of the workpiece ready for the first cut. Use the
micrometer carriage stop to control the depth of tool travel.

The same speeds recommended for straight turning should be used for straight boring. Feeds for boring should be
considerably smaller than feeds used for straight turning because there is less rigidity in the setup. Decrease the
depth of cut for each pass of the tool bit for the same reason. It is often advisable to feed the cutter bit into the hole
to the desired depth and then reverse the feed and let the cutter bit move out of the hole without changing the
depth of feed. It is also good practice to take a free cut every several passes to help eliminate bell mouthing of the
workpiece. This practice will correct any irregularities caused by the bit or boring tool bar springing because of the
pressure applied to the bit.

TAPPING AND HAND DIE THREADING

The lathe can be used as a device to hold and align a tap or hand die to cut internal or external threads quickly for
threads that do not require a high degree of accuracy or a fine finish. More information on taps and dies can be
found in TM 9-243.

Hand Tapping on the Lathe

Tapping can be done on the lathe by power or by hand. Regardless of the method, the hole must be drilled with the
proper sized tap drill and chamfered at the end. The shank end of the tap is supported by the tailstock center. A slight
pressure is maintained against the tap to keep its center hole on the center and to help the cutting teeth of the tap
engage the work (Figure 7-99).
The work will rotate when tapping using lathe power. Use a very slow spindle speed (10 to 30 RPM) and plenty of
cutting fluid or coolant. Install a tap and reamer wrench on the end of the tap to keep it from turning. Support the
wrench on the compound rest. Power is not recommended for taps under 1/2 inch in diameter or when tapping
steel. Ensure that the tap wrench handle contacts the compound rest before engaging power or the end of the
handle will whip around and could crush a finger or cause other injury or damage. Do not attempt to start the tap
into the hole with the work revolving. Always keep the tap snug in the center hole to prevent the tap from coming
out of alignment and ruining the threads.

The setup for hand tapping in a lathe is similar to that used in power tapping. The headstock chuck is held steady and
not rotated. The tap is turned by using an adjustable wrench. Lock the lathe gears so that the headstock will not
move when using a large tap. Back off the tap frequently when tapping to break the chips and allow for a clean
thread.

Hand Die Threading on the Lathe

Die threading on a lathe is very similar to tapping on a lathe, except that the die is aligned perpendicular to the work
axis by pressure exerted against the back surface of the die. This pressure can be exerted by means of a drill pad, by
using the tailstock spindle, or by using the head of the drill chuck for small dies. Die threading can be done using
power or by hand, using the same procedures as tapping. Power can be used to remove the die from the work if the
die stock handle is swung to the opposite side and low reverse power is used. It is difficult to cut very coarse threads
with a die because of the great amount of force needed to turn the die. It is advisable to open up the die to its full
width, rough-cut the threads, and then close up the die and go over the threads for a finished size. Always use a
lubricant or coolant for this operation.

REAMING ON THE LATHE

Reamers are used to finish drilled holes or bores quickly and accurately to a specified diameter. When a hole is to be
reamed, it must first be drilled or bored to within 0.004 to 0.012 inch of the finished size since the reamer is not
designed to remove much material.

Reaming with a Machine Reamer

The hole to be reamed with a machine reamer must be drilled or bored to within 0.012 inch of the finished size so
that the machine reamer will only have to remove the cutter bit marks.

The workpiece is mounted in a chuck at the headstock spindle and the reamer is supported by the tailstock in one of
the methods described for holding a twist drill in the tailstock.

The lathe speed for machine reaming should be approximately one-half that used for drilling.

Reaming with a Hand Reamer

The hole to be reamed by hand must be within 0.005 inch of the required finished size.

The workpiece is mounted to the headstock spindle in a chuck and the headstock spindle is locked after the piece is
accurately setup The hand reamer is mounted in an adjustable tap and reamer wrench and supported with the
tailstock center. As the wrench is revolved by hand, the hand reamer is fed into the hole simultaneously by turning
the tailstock handwheel.

The reamer should be withdrawn from the hole carefully, turning it in the same direction as when reaming. Never
turn a reamer backward. See Machinist Table 4-3 for the proper cutting fluid for reaming. Never use power with a
hand reamer or the work could be ruined.

FILING AND POLISHING ON THE LATHE

Filing and polishing are performed on the lathe to remove tool marks, reduce the dimension slightly, or improve the
finish.

Filing on the Lathe

Mill files are generally considered best for lathe filing. The bastard cut mill type hand file is used for roughing and the
second cut mill-type hand file for the finer class of work. Other types such as the round, half-round, and flat hand
files may also be used for finishing irregular shaped workpieces. Never use a file without a handle.

For filing ferrous metals, the lathe spindle speed should be four or five times greater than the rough turning speed.
For filing nonferrous metals, the lathe spindle speed should be only two or three times greater than the roughing
speed. Too slow a speed may cause the workpiece to be filed out of round, while too high a speed will cause the file
to slide over the workpiece, dulling the file and glazing the piece.

NOTE: When filing, file left-handed if at all possible to avoid placing your arm over the revolving chuck or lathe dog.

The file is held at an angle of about 10� to the right and moved with a slow sliding motion from left to right so that
the teeth will have a shearing action (Figure 7-100). The direction of stroke and angle should never be the opposite,
as this will cause chatter marks on the piece. The file should be passed slowly over the workpiece so that the piece
will have made several revolutions before the stroke is completed. The pressure exerted on the file with the hands
should be less than when filing at the bench. Since there are less teeth in contact with the workpiece, the file must
be cleaned frequently to avoid scratching.

Since filing should be used for little more than to remove tool marks from the workpiece, only 0.002 to 0.005 inch
should be left for the filing operation.
Polishing on the Lathe

Polishing with either abrasive cloth or abrasive paper is desirable to improve the surface finish after filing. Emery
abrasive cloth is best for ferrous metals while abrasive paper often gives better results on nonferrous materials. The
most effective speed for polishing with ordinary abrasives is approximately 5,000 feet per minute. Since most lathes
are not capable of a speed this great for an average size workpiece, it is necessary to select as high a speed as
conditions will permit.

In most cases the abrasive cloth or paper is held directly in the hand and applied to the workpiece, although it may
be tacked over a piece of wood and used in the same manner as a file. Improvised clamps may also be used to polish
plain round work.

Since polishing will slightly reduce the dimensions of the workpiece, 0.00025 to 0.0005 inch should be allowed for
this operation. Figure 7-101 shows how to hold the abrasive strip when polishing. Note that the ends of the strip are
separated. This prevents the strip from grabbing and winding around the work, which could pull the operator's hand
into the work. Move the polishing strip slowly back and forth to prevent material building up on the strip which
causes polishing rings to form on the work. To produce a bright surface, polish the work dry. To produce a dull satin
finish, apply oil as the polishing operation is in progress.

ECCENTRIC WORK ON THE LATHE

Eccentric work is work that is turned off center, or not on the normal center axis. An engine crankshaft is a good
example of an eccentric workpiece. Crankshafts normally have a main center axis, called a main journal, and offset
axes, which produce the throw and the eccentric diameters of the mechanism. An eccentric shaft may have two or
more diameters and several different center axes. The amount of eccentricity, or half of the throw, is the linear
distance that a set of center holes has been offset from the normal center axis of the workpiece. Eccentric turning on
the lathe is used for the following eccentric turning situations:

When the throw is large enough to allow all centers to be located on the workpiece at the same time.

When the throw is too small to allow all centers to fit into the end of a workpiece at the same time. (The center
drilled holes are too large.)

When the throw is so great that all centers cannot be located on the work, or in other words, a throw larger than the
largest diameter of the workpiece. (This type of crank is usually made in separate pieces and connected together,
since the cost of wasted material would be too great if constructed from one piece on the lathe).

Turning an Eccentric with Center Holes

Before an eccentric workpiece can be machined, it is necessary to center-drill both ends of the workpiece, including
the offset centers. If the workpiece is large enough to position all center axes on the work at the same time, the
machining operation will be simple and easy.
  First determine the stock required by adding the throws plus 1/8 inch for machining (Figure 7-102).
 Face the work to length in a chuck.
 Remove the piece and apply layout dye to both ends.
 Mount the work in a V- block and, using a surface plate and venire height scriber, lay out the normal center
axis and the offset center axes on both ends.
 Accurately prick punch the intended centers, check for accuracy, and then enlarge the punch marks with a
center punch.
 Center- drill both sets of center punch marks by using a milling machine, a drilling machine, or the four-jaw
independent chuck of the lathe with a dial indicator to line up the centers.
 Mount the work in the lathe between centers and turn the largest diameter first. If all diameters are the
same, turn the middle diameter
journal first.
 After turning the center journal
down to the required diameter,
remount the work in an offset center
hole and machine the throw
diameter to the finished size.
 Accurately prick punch the intended
centers, check for accuracy, and then
enlarge the punch marks with a
center punch.
 Center- drill both sets of center
punch marks by using a milling
machine, a drilling machine, or the
four-jaw independent chuck of the
lathe with a dial indicator to line up
the centers.
 Mount the work in the lathe
between centers and turn the largest
diameter first. If all diameters are
the same, turn the middle diameter
journal first.
 After turning the center journal
down to the required diameter,
remount the work in an offset center
hole and machine the throw
diameter to the finished size.

Additional throws are machined in the same

manner. Throw positions may be started by
cutting with a parting tool to establish the
shoulders, which may aid the turning
operation. The tool bit selected will depend
on the material to be machined and on the
depth of cut desired.

Turning an Eccentric with Close Center

Holes

If turning an eccentric that has the different

centers placed too close together, a different
procedure should be used. Cut the stock 3/4
inch oversized and just face both ends to
clean up the saw cuts Lay out and center-drill the normal. center axis and turn down those diameters on the center
axis with the work mounted between centers. Remove the work and remount into a chuck. Face both ends to the
required length and center-drill the offset centers. Remount the work between these centers and machine the
eccentric diameters to size. For eccentric work that has a limited distance between each center, this method is safer
than trying to use a very shallow center-drilled hole to hold the work between centers (Figure 7-102).

Turning an Eccentric Using Throw Plates

If the lathe is to be used to turn a crank with a great throw, or a throw that is greater than normally machined on a
lathe (Figure 7-102), special throw plates must be fabricated to hold the ends of the work while turning. The special
throw plates will be used as support blocks to enable the offset center holes to be machined into the throw plates
and allow for eccentric turning. eccentric turning, it is not recommended for normal lathe operations. Special
crankshaft turning and grinding equipment is available for this type of machining.

RECESSING DRILLED AND BORED HOLES

General

Recessing, sometimes called channeling or cambering, is the process of cutting a groove inside of a drilled, bored, or
reamed hole. Recesses (Figure 7-103) are usually machined to provide room for the tool runout needed for
subsequent operations such as internal threading.

A boring bar and holder may be used as a recessing tool, since recessing tools have the same tool angles and are
similar in shape to boring tools. A high-speed steel cutting tool bit, ground with a square nose, makes a satisfactory
tool for cutting small chambers (Figure 7-103). The sides of the tool bit taper in from the cutting edge so that the
nose of the tool is the widest part. The tool bit must extend from the holder a distance slightly greater than the
depth of the chamber to prevent the holder from rubbing the bore of the work.

Machining a Recess

To cut a recess, set up the lathe as in a boring operation. Reference the face of the tool bit to the face of the work;
then move the tool bit forward the required distance to the recess by using the micrometer stop or by using the
compound rest graduated collar. The compound rest must be set parallel with the ways of the bed for this method.
Add the width of the tool bit into the measurement or the recess will not be cut correctly. Position A (Figure 7-103) is
the tool aligning to the work, position B is set over to the front shoulder of the recess, and position C is the set over
to the back of the recess. Use the cross slide graduated collar to measure the distance to move the tool bit toward
the operator, inside of the hole. Spindle speed may have to be reduced due to the shape of the tool bit causing
chatter on the work. After cutting the recess, use inside calipers to check the diameter.

LATHE TOOL POST GRINDER

General
The tool post grinder is a portable grinding machine that can be mounted on the compound rest of a lathe in place of
the tool post. It can be used to machine work that is too hard to cut by ordinary means or to machine work that
requires a very fine finish. Figure 7-29 shows a typical tool post grinder. The grinder must be set on center, as shown
in Figure 7-104. The centering holes located on the spindle shaft are used for this purpose. The grinding wheel takes
the place of a lathe cutting tool. It can perform most of the operations that a cutting tool is capable of performing.
cylindrical, tapered, and internal surfaces can be ground with the tool post grinder. Very small grinding wheels are
mounted on tapered shafts known as quills to grind internal surfaces.

Selection of Grinding Wheels and Speeds

The grinding wheel speed is changed by using various sizes of pulleys on the motor and spindle shafts. An instruction
plate on the grinder gives both the diameter of the pulleys required to obtain a given speed and the maximum safe
speed for grinding wheels of various diameters. Grinding wheels are safe for operation at a speed just below the
highest recommended speed. A higher than recommended speed may cause the wheel to disintegrate. For this
reason, wheel guards are furnished with the tool post grinder to protect against injury. Always check the pulley
combinations given on the instruction plate of the grinder when you mount a wheel. Be sure that the combination is
not reversed, because this may cause the wheel to run at a speed far in excess of that recommended. During all
grinding operations, wear goggles to protect your eyes from flying abrasive material.

Dressing the Grinding Wheel

The grinding wheel must be dressed and trued. Use a diamond wheel dresser to dress and true the wheel. The
dresser is held in a holder that is clamped to the drive plate. Set the point of the diamond at center height and at a
10� to 15� angle in the direction of the grinding wheel rotation. The 10� to 15� angle prevents the diamond
from gouging the wheel. Lock the lathe spindle by placing the spindle speed control lever in the low RPM position.

NOTE: The lathe spindle does not revolve when you are dressing the grinding wheel.

Remove the diamond dresser holder as soon as the dressing operation is completed. Bring the grinding wheel in
contact with the diamond by carefully feeding the cross slide by hand. Move the wheel clear of the diamond and
make a cut by means of the cross slide. The maximum depth of cut is 0.002 inch. Move the wheel slowly by hand
back and forth over the point of the diamond. Move the carriage if the face of the wheel is parallel to the way of the
lathe. Move the compound rest if the face of the wheel is at an angle. Make the final depth of cut of 0.0005 inch with
a slow, even feed to obtain a good wheel finish.

Before you begin the grinding operation, cover the ways with a heavy piece of paper or use a shallow pan of water
placed on the ways to collect the grinding dust that will accumulate from the grinding. This is to ensure none of the
grinding burns to the ways or gets under the carriage which will cause the lathe premature wear. If you use a piece of
paper, pay close attention that the sparks from the grinding operation do not cause the paper to ignite. If you use a
shallow pan of water, make sure water is not spilled on the ways of the lathe. After all grinding operations,
thoroughly clean and oil the lathe to remove any grinding dust that the paper pan of water missed.

Grinding Feeds, Speeds, and Depth of Cuts

Rotate the work at a fairly low speed during the grinding operations. The recommended surface foot speed is 60 to
100 FPM. The depth of cut depends upon the hardness of the work, the type of grinding wheel, and the desired
finish.

Never take grinding cuts deeper than 0.002 inch Use a fairly low rate of feed. You will soon be able to judge whether
the feed should be increased or decreased. Never stop the rotation of the work or the grinding wheel while they are
in contact with each other.

Marking Position of Lathe Centers

Tool post grinders are often used to refinish damaged lathe centers. If the lathe is to be used for turning between
centers in the near future, grind the tailstock center first, then the headstock center. Leave the headstock center in
position for the turning operation. This method provides the greatest degree of accuracy. If you must remove the
headstock center in order to perform other operations, marks placed on the headstock center, the sleeve, and the
center will enable you to install them in the same position they were in when the center was ground. This will ensure
the greatest degree of accuracy for future operations involving turning work between centers.

Setup for Grinding Lathe Centers

To refinish a damaged lathe center, you should first install headstock and tailstock centers after ensuring that the
spindle holes, drill sleeves, and centers are clean and free of burrs. Next, position the compound rest parallel to the
ways; then, mount the tool post grinder on the compound rest. Make sure that the grinding wheel spindle is at
center height and aligned with the lathe centers. Move the compound rest 30� to the right of the lathe spindle axis,
as shown in Figure 7-40. Mount the wheel dresser, covering the ways and carriage with rags to protect them from
abrasive particles. Wear goggles to protect your eyes.

Grinding Lathe Centers

Start the grinding motor. Turn it on and off alternately, but let it run a bit longer each time, until the abrasive wheel is
brought up to top speed. Dress the wheel, feeding the grinder with the compound rest. Then move the grinder clear
of the headstock center and remove the wheel dresser. Set the lathe for the desired spindle speed and engage the
spindle. Pick up the surface of the center. Take a light depth of cut and feed the grinder back and forth with the
compound rest. Do not allow the abrasive wheel to feed entirely off the center. Continue taking additional cuts until
the center cleans up. To produce a good finish, reduce the feed rate and the depth of cut to 0.0005. Grind off the
center's sharp point, leaving a flat with a diameter about 1/32 inch. Move the grinder clear of the headstock and turn
it off.

MILLING ON THE LATHE

Milling operations may be performed on the lathe by using the Versa-Mil, which is discussed in Chapter 9, and by
using the lathe milling fixture. The lathe milling fixture complements the Versa-Mil and adds to the basic capabilities
of the machine shop. If the Versa-Mil is out of action or being used for another job, many milling operations can still
be accomplished by using the milling fixture (Figure 7-105). Capabilities, functions, and uses are outlined in the
appropriate operator's manual, either TM 9-3465-200-10 or TM 9-3465-201-10.
USING MICROMETER CARRIAGE STOP

The micrometer carriage stop, shown in Figure 7-28, is used to accurately position the lathe carriage. Move the
carriage so that the cutting tool is approximately positioned. Clamp the micrometer carriage stop to the ways of the
lathe, with the spindle in contact with the carriage. The spindle of the micrometer carriage stop can be extended or
retracted by means of the knurled adjusting collar. The graduations on the collar, which indicate movement in
thousandths of an inch, make it possible to set the spindle accurately. Next, bring the carriage in contact with the
micrometer spindle again. The carriage can be accurately positioned within 0.001 inch. This is very useful when you
are facing work to length, machining shoulders to an exact length, or accurately spacing internal and external
grooves. After making a cut, bring the tool back to the start of the cut by means of the carriage stop. This feature is
very useful when you must remove a tool, such as the internal recessing tool, from the hole to take measurements
and then reposition it to take additional cuts. Always bring the carriage into contact with the stop by hand. Use
power feed to bring the carriage within 1/32 inch of the stop. Move the carriage by hand the remaining distance.

USING STEADY AND FOLLOWER RESTS

General

The steady rest consists of a frame and three adjustable jaws which support the work, as shown in Figure 7-27. One
purpose of the steady rest is to prevent springing or deflection of slender, flexible work; another is to furnish auxiliary
support for the work to permit heavy cuts to be made; a third is to support work for drilling, boring, or internal
threading. The over arm containing the top jaw can be unfastened and swung out of the way so that identical pieces
can be removed and replaced without adjusting the jaws.

Bearing Surface

A bearing surface must be provided for

the steady rest jaws. The bearing surface
is usually machined directly on the work,
as shown in Figure 7-106. When the
work is too small in diameter to machine
the bearing surface or shaped so that it
would be impractical to machine one,
you can use a cathead to provide the
bearing surface. The cathead shown in
Figure 7-27, has a bearing you surface, a
hole through which the work extends,
and adjusting screws. The adjusting
screws fasten the cathead to the work.
They are also used to align the bearing
surface so can use a cathead to provide the bearing surface so that t is concentric to the work axis. Use a dial
indicator to ensure concentricity.

Setting up the Steady Rest

To setup the rest, first machine and polish the portion of the work that is to be used as the bearing surface. Clean the
portion of the ways where the steady rest is to be mounted, place the steady rest on the ways and clamp loosely.
Open the top of the steady rest and place the workpiece in the chuck with the bearing surface over the adjustable
jaws. Clamp the steady rest securely to the ways. Close the top of the steady rest and adjust the jaws to the
workpiece. There should be 0.001 inch clearance between the jaws and the workpiece. Tighten the locking screws on
the adjustable jaws. Lubricate the bearing surface generously with a heavy oil before turning the lathe on. Proceed
with the machining operation Continuously watch the bearing surface and the adjustable jaws to ensure a film of
heavy oil is between them. As the machining operation continues, also check the bearing surface and adjustable jaws
as when the workpiece heats up it will expand, closing the distance between the jaws and the workpiece.

Using Steady Rest with Headstock Center

When it is not possible to hold the work in the chuck, you can machine with one end supported by the headstock
center and the other end supported by the steady rest. Use a leather strap or rawhide thong to tie the work to the
driveplate and to prevent it from moving off the headstock center, as shown in Figure 7-107. Mount the work
between centers and machine the bearing surface. Set up the steady rest. With the work mounted between the
centers, tie the lathe dog, then remove the tailstock center and perform the necessary machining.

Using the Follower Rest

Long slender shafts that tend to whip and spring while they are being machined require the use of a follower rest
(Figure 7-27). The follower rest is fastened to the carriage and moves with the cutting tool. The upper jaw prevents
the work from climbing the cutting tool. The lower jaw prevents the work from springing away from the cutting tool
The follower rest jaws are adjusted in the same manner as steady rest jaws. The follower rest is often used when
long, flexible shafts are threaded, as shown in Figure 7-108. At the completion of each threading cut, remove any
burrs that may have formed to prevent them from causing the work to move out of alignment.
Why is proper Cutting Speed important?
When set too high the tool breaks down quickly, time is lost replacing or reconditioning the tool. Too low of a CS
results in low production.

Know:

• Depth of cut for Roughing.

• Depth of cut for Finishing.

Notice the largest roughing cuts range from .010 to .030 depending on the material being machined, and .002 to .012
for the finish feed for the different materials.

• Feedrate for Roughing cut

• Feedrate for Finishing cut

Notice the Feedrate for roughing cuts range from .005 to .020 depending on the material being machined, and .002
to .004 for the finish feed for the different materials.

Cutting Tool Terminology

There are many different tools that can be used for turning, facing, and parting operations on the lathe. Each tool is
usually composed of carbide as a base material, but can include other compounds. This section covers the different
appearances and uses of lathe cutting tools.

Figure A:depicts a standard turning tool to create a

semi-square shoulder. If there is enough material
behind the cutting edge, the tool can also be used for
roughing.
Figure A

Figure B:depicts a standard turning tool with a lead angle.

This angle enables for heavy roughing cuts. Ititalso possible
to turn the tool to create a semi-square shoulder.
Figure B
 Figure C:nose has a very large radius, which helps with
fine finishes on both light and heavy cuts. The tool can
also be used to form a corner radius.

Figure C

Figure D:depicts a rotated standard turning tool. Its

nose leads the cutting edge to create light finishing
cuts on the outside diameter and face of the shoulder.

Figure D

Figure E:depicts a form tool. Different forms can be ground into the tool, which will be
reproduced onto the part. Figure E

Figure F:depicts a facing tool. This cutter is

used to face the end of a workpiece to
provide for a smooth, flat finish. If the
stock has a hole in the center, utilize a Figure F
half-center to stabilize and support the
workpiece.
 Figure G:depicts a grooving or under-cutting tool. As shown,
it is used to cut grooves into the workpiece. When there are
proper clearances, the tool can cut deeply, or cut to the left
or right.

Figure H:depicts a parting tool. Parting tools cut off the

stock at a certain length. This tool requires a preformed
blade and holder
Figure H

. Figure I:depicts a 60° threading tool used to thread stock.

Figure I

To setup a Cutting Tool for Machining

• Move the toolpost to the left-hand side of the compound rest.
• Mount a toolholder in the toolpost so that the set screw in the toolholder is about 1 inch beyond the
toolpost.
• Insert the proper cutting tool into the toolholder, having the tool extend .500 inch beyond the toolholder.
• Set the cutting tool point to center height. Check it with straight rule or tailstock.
 • Tighten the toolpost securely to prevent it from moving during a cut

Figure 2: Toolpost and Toolholder

To Mount Workpiece in Lathe

• Check that the line center is running true. If it is not running true, remove the center, clean all surfaces, and
replace the center. Check again for trueness.
• Clean the lathe center points and the center holes in the workpiece.
• Adjust the tailstock spindle until it projects about 3 inch beyond tailstock.
• Loosen the tailstock clamp nut or lever.
• Place the end of the workpiece in the chuck and slide the tailstock up until it supports the other end of the
workpiece.
• Tighten the tailstock clamp nut or level.

Installing a Cutting Tool

• Tool holders are used to hold lathe cutting tools.
• To install, clean the holder and tighten the bolts.
• The lathe’s tool holder is attached to the tool post using a quick release lever.
• The tool post is attached to the machine with a T-bolt.

Figure 4: Installing a Cutting Tool

Positioning the Tool

To reposition the cutting tool, move the cross slide and lathe saddle by hand. Power feeds are also available. Exact
procedures are dependent on the machine. The compound provides a third axis of motion, and its angle can be
altered to cut tapers at any angle.

1. Loosen the bolts that keep the compound attached to the saddle.
2. Swivel the compound to the correct angle, using the dial indicator located at the compound’s base.
3. Tighten the bolts again.
4. The cutter can be hand fed along the chosen angle. The compound does not have a power feed.
 5. If needed, use two hands for a smoother feed rate. This will make a fine finish.
6. Both the compound and cross slide have micrometer dials, but the saddle lacks one.
7. If more accuracy is needed when positioning the saddle, use a dial indicator that is attached to the saddle.
Dial indicators press against stops.

Figure 5: Positioning the Tool

Centering the Workpiece

Steel Rule

1. Place the steel rule between the stock and the tool.
2. The tool is centered when the rule is vertical.
3. The tool is high when the rule is lean forward.
4. The tool is low when the rule is lean backward.

Tailstock Center
1. Reference the center of the tailstock when setting the tool.
2. Position the tip of the tool with the tailstock center.
UNIT TEST
1. Please list the ten most important parts of the Lathe.
2. Please list five Lathe safety guidelines.
3. Why is cutting speed important?
4. What is a Toolholder?
5. Where do you mount a Toolholder?
6. How far do you extend the cutting tool in the Toolholder?
7. Please list three different cutting tools.
8. Please describe the positioning of the tool.
9. Explain how to center the workpiece.
10. What are the two way to center the workpiece?
xx