OPERATOR’S MANUAL

NX3000 HAND PALLET TRUCK

ACTUAL PRODUCT MAY NOT APPEAR EXACTLY AS SHOWN

WARNING
Do not operate or service this product unless you have read and fully
understand the entire contents of this manual. Failure to do so may result in
property damage, bodily injury or death.

ISSUE DATE: JULY 13, 2016 REV.1 (PART # 038-697E)

NX3000 HAND PALLET TRUCK—OPERATOR’S MANUAL

TABLE OF CONTENTS

1.0 SAFETY PROCEDURES 3

2.0 EXCLUSION OF LIABILITY 3

3.0 OWNER’S PURCHASE RECORD 4

4.0 WARRANTY 4

5.0 CHECK SHIPMENT BEFORE ASSEMBLY AND/OR USE 5

5.1 LOADING SPECIFICATION 5

5.2 MAXIMUM INCLINES OR DECLINE GRADES 5

5.3 SAFETY WITH TALL LOADS 5

6.0 NX3000 HAND PALLET TRUCK SPECIFICATIONS

6

7.0 ASSEMBLY INSTRUCTIONS 7

7.1 BEFORE USE 7

8.0 OPERATING INSTRUCTIONS 8

9.0 SERVICE CHECKLIST 9

10.0 TROUBLESHOOTING GUIDE 10

11.0 HANDLE AND PUMP ASSEMBLY DRAWING 11

11.1 HANDLE AND PUMP ASSEMBLY PARTS LIST 12

11.2 FRAME ASSEMBLY DRAWING 14

11.3 FRAME ASSEMBLY PARTS LIST 15

DEALER INFORMATION

Name:
Contact:

Telephone:

2 ISSUE DATE: JULY 13, 2016 REV.1 (PART # 038-697E)

 NX3000 HAND PALLET TRUCK—OPERATOR’S MANUAL

1.0 SAFETY PROCEDURES

1. Do not operate this truck unless you have been trained and authorized to do so.
2. Do not operate this truck until you have read and understood all of the safety information
and instructions contained herein and on the truck.
3. Do not operate this truck until you have checked its condition. Give special attention to
wheels, controls and lifting systems, including steering mechanism, guards and safety
devices.
4. Report the need for truck repairs to your supervisor immediately and do not operate truck
until repairs are made. Neglect may cause a minor repair to become a major service
problem and cause the truck to become unsafe.
5. Do not load truck beyond capacity shown on serial name plate on truck.
6. Do not lift with the fork tips or one fork only.
7. This equipment is designed for evenly centered loads with forks completely supporting the
load. Off-centering of loads can result in a dangerous operating condition and may cause
damage or injury.
8. Always look in direction of travel. Use caution when visibility is obstructed by load.
9. Extreme caution must be used when handling loosely stacked/packaged loads.
10. Watch swing clearance when turning near walls, racks. pillars or other obstacles.
11. Start, stop, change direction and travel smoothly. Slow down for turns and on uneven
or slippery surfaces that cause truck to slide or tip. Be aware that the truck behaves
differently without a load than with a load.
12. Observe applicable traffic regulations. Yield right of way to pedestrians.
13. Do not ride on this equipment.
14. Do not carry passengers or lift personnel.
15. Before you leave the truck, fully lower lifting mechanism.

2.0 EXCLUSION OF LIABILITY

The manufacturer assumes no liability for damage or injury to persons or property which has
occurred as a result of defects or faults in the hand pallet trucks delivered or due to incorrect
use. The manufacturer also assumes no liability for lost profits, operating down times, or
similar indirect losses which the buyer has incurred. Damage to third parties, irrespective of its
nature, is not subject to compensation.

The operating instructions are not subject to notification of amendment. The descriptions and
illustrations included in our operating instructions and replacement parts list are not binding.
In the interests of further development, we reserve the right to make any changes at any time
to the modules, components and accessories which we deem to be expedient, or for technical
reasons, while retaining the essential features of the models described here.

ISSUE DATE: JULY 13, 2016 REV.1 (PART # 038-697E) 3

NX3000 HAND PALLET TRUCK—OPERATOR’S MANUAL

3.0 OWNER’S PURCHASE RECORD

OWNER’S PURCHASE RECORD

Please record information for future inquiries and to validate warranty.

Dealer: Date in Service:

Number of Units:

Owner’s Name: Order Number:

Serial Number: Year of Construction:

4.0 WARRANTY

To validate warranty on recently purchased equipment, please complete and

submit your information with our online Warranty Registration at
www.bluegiant.com.

For more information about Blue Giant Warranty Support, please contact your local Blue Giant
Equipment dealer, representative or authorized partner near you. You may also visit
www.bluegiant.com or phone 1.905.457.3900.

* Note that failure to validate warranty at the time of receipt can seriously affect the outcome
of any claim.

4 ISSUE DATE: JULY 13, 2016 REV.1 (PART # 038-697E)

 NX3000 HAND PALLET TRUCK—OPERATOR’S MANUAL

5.0 CHECK SHIPMENT BEFORE ASSEMBLY AND/OR USE

The hand pallet truck is to be carefully checked at the manufacturer’s plant before shipment.
In order to ensure that no damage has occurred during transport, the hand pallet truck should
be checked upon receipt for transport damage and to ensure correct operation. Damage due
to transport is to be listed on the signed copy on the freight document. The freight forwarder
must be notified of any damage within 48 hours. Damaged hand pallet trucks must not be
put into use.

5.1 LOADING SPECIFICATION

The hand pallet truck is designed for the horizontal transportation of loads on a level, fixed
base. The load must be evenly distributed on pallets or similar receptacles. The ideal loading
mode is that the gravity center of heavy goods is at the central position of the fork. The
maximum load-carrying capacity is shown on the appropriate designation plate and on the load
sticker on the hand pallet truck. When there exists deflective load, the rated carrying capacity
shall be reduced. If the load on the forks is one sided, there is a risk of the forks bending or the
load slipping off. Supporting or shifting the load with the fork tips is to be avoided in all
cases as this results in damage to the appliance. In order to preserve the wheels and chassis
the hand pallet truck must not be driven over very uneven ground.

5.2 MAXIMUM INCLINES OR DECLINE GRADES

The hand pallet truck is equipped with a permanently set pressure-limiting valve which permits
a maximum load of 5 % of the nominal load. The screw plug on the pressure control valve
is secured so as to avoid inappropriate manipulation from the operating personnel. In order
to avoid damage to the goods being transported and the means of transport, the load must
be supported evenly. If the load is unevenly distributed the pressure limiting valve will not
function. When driving on down-grades the load is to be secured to prevent it from slipping
or sliding off the hand pallet truck, (e.g. additional operating personnel). In addition to this,
only hand pallet trucks with a service and parking brake are to be used on down-grades up to
approx 6 %. Journeys on inclines or down-grades of more than 6 % are always to be avoided.
Safe transport cannot be guaranteed when the center of gravity of the load has altered.

5.3 SAFETY WITH TALL LOADS

Transporting with tall loads, (e.g. machines) changes the center of gravity of the load so
unfavorably that the complete hand pallet truck including the load, goes out of control and may
overturn on a curve. Loading, (e.g. onto a truck or mobile loading ramps) should be regarded
in particular as likely occasions for accidents. During such activities the hand pallet truck is
to be secured with particular care. Conveying persons or using the hand pallet truck as a form
of roller skate is not permissible. Foodstuffs are only to be transported in packed form. Direct
contact with the hand pallet truck is to be avoided. The accident prevention regulations for
industrial trucks and the safety regulations and accident prevention regulations applicable to
the user are also to be complied with.

ISSUE DATE: JULY 13, 2016 REV.1 (PART # 038-697E) 5

NX3000 HAND PALLET TRUCK—OPERATOR’S MANUAL

6.0 NX3000 HAND PALLET TRUCK SPECIFICATIONS

The following data must always be specified to ensure correct processing of your spare parts
order:

A) Truck type (capacity)

B) Serial number of the truck
C) Complete Part Number

ASSEMBLY DRAWINGS:
Handle and Pump Assembly
Frame Assembly

WEIGHT:
160 lbs (72.575 kg)

CAPACITY:
5,500 lbs (2,300 kg)

FORK LENGTH:
48" (1,220 mm)

Please fill in Owner’s Purchase Record (Section 3.0) with the following details:
- Serial Number(s)
- Dealer Name
- Date in-Service
- Owner’s Name
- Order Number
- Year of Construction

6 ISSUE DATE: JULY 13, 2016 REV.1 (PART # 038-697E)

 NX3000 HAND PALLET TRUCK—OPERATOR’S MANUAL

7.0 ASSEMBLY INSTRUCTIONS

Individual trucks are assembled and ready to use. Pallet trucks purchased in crate quantities (6
units to a crate) require some assembly. Tools Needed for Assembly: 5 mm / 8 mm Allen Key
1. Remove screw (No. 1), before pulling 3. Put screw and nut at the end of roller
axle pin (No. 2) chain (No. 5) into the slot of lever pad
2. Insert handle (No. 3) at position (No. (No. 6)
A) and connect handle (No. 3) to 4. Pull the handle to horizontal position,
pump body pull out pin (No. 7) and keep it stored for
(No. 4) insert axle pin (No. 2) then use future handle replacement
Allen Key to fasten screw (No. 1) to 5. The assembly is complete
attach axle pin (No. 2)

1 2 3

7.1 BEFORE USE

1. After finishing the assembly of the pallet truck, try to shake it and operate the unit in
different positions using the hand lever, to see whether the lifting, neutral position and
lowering the pallet truck operates properly.
2. The outer hexagonal nut (No. 10) at bolt location (No. 9) is used for locking, and must
be loosened before any adjustment and must be tightened after adjustment. If the pallet
truck is raised and the pallet truck immediately descends, turn screw bolt (No. 9) anti-
clockwise a little at a time and test the pallet truck until normal lifting has occurred. If the
pallet truck cannot be lowered after lifting, turn screw bolt (No. 9) clockwise a little at a
time and test the pallet truck until normal lowering has occurred. After adjustments lock
outer hexagonal nut (No. 10) at bolt location (No. 9) back into place.

ISSUE DATE: JULY 13, 2016 REV.1 (PART # 038-697E) 7

NX3000 HAND PALLET TRUCK—OPERATOR’S MANUAL

8.0 OPERATING INSTRUCTIONS

NOTES ON USE

There is a hand lever on the drawbar for raising and lowering the hand pallet truck. This can be
moved into three positions:

NEUTRAL LOWER LIFT

DRIVE POSITION Lever up, truck will lower at Lever down
Lever in neutral position selected rate of speed
when moving load
(center position)

To pull the hand pallet truck, always move the hand lever into the drive position. This makes
the drawbar easier to move and depressurizes the pump section of the hydraulics. This
preserves the hydraulic seals and the valve components. A longer service life can be expected.

The hand pallet truck is largely maintenance-free. Only the oil level has to be checked and
topped up if necessary. All bearings and shafts are provided with long-life grease at the
factory.

All lubrication points marked ( ) in the “chassis” replacement parts list are to be provided
with long-life grease at monthly intervals or after each time the truck is cleaned thoroughly.

NOTE: When the hand pallet truck is used under extreme conditions (e.g. extreme heat or cold,
very dusty conditions etc.), the stipulated intervals are to be appropriately reduced.

8 ISSUE DATE: JULY 13, 2016 REV.1 (PART # 038-697E)

 NX3000 HAND PALLET TRUCK—OPERATOR’S MANUAL

9.0 SERVICE CHECKLIST

• With control lever in lift position, pump the handle a few

strokes to lift load
• Move control lever to neutral position to free handle of all
OPERATION
pumping force
• To lower load, pull the lever until the load starts lowering or the
selected lowering speed has been reached

• With the truck in the lowered position on a level surface,

CHECKING OIL
remove filter screw, oil should be level with filler screw hole, if
LEVEL
not add the proper oil. Check filler screw seal before replacing

• The hydraulic oil required for the hydraulic pump is roughly

0.5 pints (250 ml). The ISO oil quality standard is used.
RECOMMENDED
When the ambient temperature is -5˚ to 40˚C, #32 oil is
HYDRAULIC OIL
used; and when the ambient temperature is -35˚ to -5˚C,
the low temperature hydraulic oil is to be used

• Conduct routine inspection everyday to eliminate future

problems from occurring
MAINTENANCE
• Do not use pallet trucks that are not working properly
• Add motor oil to each rotating joint once every three months

ISSUE DATE: JULY 13, 2016 REV.1 (PART # 038-697E) 9

NX3000 HAND PALLET TRUCK—OPERATOR’S MANUAL

10.0 TROUBLESHOOTING GUIDE

CONDITION CAUSE ACTION

A Shortage of oil A Add appropriate filtered working oil
Insufficient lifting
Set operation lever to lowering
B Air in pump B
position and pump handle repeatedly

Too much hydraulic Pump off appropriate amount of

A A
oil has been added hydraulic oil
Pallet truck does not
completely lower Rotating part is
B distorted and gets B Replace parts
stuck

The lowering device Re-adjust the lowering device

A A
is abnormal See Before Use (Section 7.1)
Pallet truck does not lower
after lifting Components are
B distorted and B Replace required parts
damaged

The seal is
A A Replace the seal
damaged

There is a slight
breakage or
Hydraulic oil leaks
B abrasion on the B Replace the damaged parts
surface of the
individual parts

C Loose joint C Tighten the loose joint

Viscosity of
hydraulic oil is too
A A Replace the hydraulic oil
high or hydraulic oil
level is too low
Pallet truck does not lift
B Hydraulic oil is dirty B Replace the hydraulic oil

The lowering device Re-adjust the lowering device.

C C
is abnormal See Before Use (Section 7.1)

Pallet truck lifts then

immediately descends
Open the valve, take it out and clean
when handle is pumped
the valve and parts
A The valve is stuck A
The handle has large
Re-install the valve and parts to their
resistance or the pallet
original position
truck automatically
descends after lifting

10 ISSUE DATE: JULY 13, 2016 REV.1 (PART # 038-697E)

 NX3000 HAND PALLET TRUCK—OPERATOR’S MANUAL

11.0 HANDLE AND PUMP ASSEMBLY DRAWING

Enlarged for clarity.

ISSUE DATE: JULY 13, 2016 REV.1 (PART # 038-697E) 11

NX3000 HAND PALLET TRUCK—OPERATOR’S MANUAL

11.1 HANDLE AND PUMP ASSEMBLY PARTS LIST

DRAWING REF NO. PART NO. QTY DESCRIPTION

B101 080-7E101 1 Blade Spring

B102 080-7E102 2 Spring Pin

B103 080-7E103 1 Roller

B104 080-7E104 1 Spring Pin

B105 080-7E105 1 Spring Pin

B106 080-7E106 1 Spring Pin

B107 080-7E107 1 Handle

B108 080-7E108 1 Handle Tube

B109 080-7E109 1 Shaft

B110 080-7E110 1 Spring Pin

B111 080-7E111 1 Pressure Roller

B112 080-7E112 2 Bush

B113 080-7E113 1 Pull Pole

B114 080-7E114 2 Bush

B115 080-7E115 1 Chain

B116 080-7E116 1 Nut

B117 080-7E117 2 Bolt

B118 080-7E118 2 Screw Plug

B119 080-7E119 1 Plug

B120 080-7E120 2 Copper Washer

B121 080-7E121 1 Spring

B122 080-7E122 1 Spindle of Damping Valve

B123 080-7E123 1 Seat of Damping Valve

B124 080-7E124 1 Steel Ball

B125 080-7E125 2 Base

B126 080-7E126 2 Copper Washer

B127 080-7E127 2 Bolt

12 ISSUE DATE: JULY 13, 2016 REV.1 (PART # 038-697E)

 NX3000 HAND PALLET TRUCK—OPERATOR’S MANUAL

11.1 HANDLE AND PUMP ASSEMBLY PARTS LIST CON’T.

DRAWING REF NO. PART NO. QTY DESCRIPTION

B128 080-7E128 1 Spring

B129 080-7E129 1 Strike Pin

B130 080-7E130 1 O-Ring

B131 080-7E131 1 Axle Sleeve

B132 080-7E132 1 O-Ring

B133 080-7E133 1 Bolt

B134 080-7E134 1 Nut

B135 080-7E135 1 Lever Plate

B136 080-7E136 1 Bolt

B137 080-7E137 1 Spring

B138 080-7E138 1 Ball Base

B139 080-7E139 1 Steel Ball

B140 080-7E140 1 Pin

B141 080-7E141 1 Y-Ring

B142 080-7E142 1 O-Ring

B143 080-7E143 1 Cylinder Cap

B144 080-7E144 1 O-Ring

B145 080-7E145 1 Dust Ring

B146 080-7E146 1 Steel Ball

B147 080-7E147 1 Pump Plunger

B148 080-7E148 1 Washer

B149 080-7E149 1 Spring

B150 080-7E150 1 Dust Ring

B151 080-7E151 1 Y-Ring

B152 080-7E152 1 Piston Rod

B153 080-7E153 1 Retaining Ring for Axle

B154 080-7E154 1 Washer

ISSUE DATE: JULY 13, 2016 REV.1 (PART # 038-697E) 13

NX3000 HAND PALLET TRUCK—OPERATOR’S MANUAL

11.2 FRAME ASSEMBLY DRAWING

14 ISSUE DATE: JULY 13, 2016 REV.1 (PART # 038-697E)

 NX3000 HAND PALLET TRUCK—OPERATOR’S MANUAL

11.3 FRAME ASSEMBLY PARTS LIST

DRAWING REF NO. PART NO. QTY DESCRIPTION

– 080-7E0 1 Complete Pump Assembly

B1 080-7E1 1 Handle and Pump Complete

B2 080-7E2 1 Steer Wheel Shaft

B3 080-7E3 1 Steer Axle Bolt

B4 080-7E4 1 Thrust Bearing

B5 080-7E5 1 Supporting Base

B6 080-7E6 2 Spring Pin

B7 080-7E7 1 Retaining Ring for Axle

B8 080-7E8 2 Steer Wheel Polyurethane

– 080-7E8N 2 Steer Wheel - Nylon

– 080-7E8NW 2 Steer Wheel - Nylon (white)

– 080-7E8S 2 Steer Wheel - Steel

B9 080-7E9 8 Bearing

B10 080-7E10 4 Half Round Locking Ring

B11 080-7E11 2 Bowl Washer

B12 080-7E12 2 Retaining Ring for Axle

B13 080-7E13 2 Dust Cover

B14 080-7E14 2 Bell Crank Pin

B15 080-7E15 8 Oiler

B16 080-7E16 2 Spring Pin

B17 080-7E17 2 Joint

B18 080-7E18 2 Pin

B19 080-7E19 2 Straight Tappet

B20 080-7E20 1 Long Shaft

B21 080-7E21 2 Retaining Ring for Hole

B22 080-7E22 4 Oiler

B23 080-7E23 2 Roll Sheath

ISSUE DATE: JULY 13, 2016 REV.1 (PART # 038-697E) 15

NX3000 HAND PALLET TRUCK—OPERATOR’S MANUAL

11.3 FRAME ASSEMBLY PARTS LIST CON’T.

DRAWING REF NO. PART NO. QTY DESCRIPTION

B24 080-7E24 2 Spring Pin

B25 080-7E25 2 Shaft

B26 080-7E26 2 Shaft

B27 080-7E27 2 Spring Pin

B28 080-7E28 4 Roll Ring

B29 080-7E29 2 Shaft

B30 080-7E30 2 Spring Pin

B31 080-7E31 2 Frame or Fork Wheel

B32 080-7E32 8 Spring Pin

B33 080-7E33 4 Shaft

B34 080-7E34 4 NOG of Fork Wheel

B35 080-7E35 2 Load Roller - Polyurethane

– 080-7E35N 2 Load Roller - Nylon

– 080-7E35S 2 Load Roller - Steel

B36 080-7E36 2 Bolt

B37 080-7E37 2 Sheath

B38 080-7E38 2 Front Guide Roller

B39 080-7E39 2 Nut

B40 080-7E40 1 Fork Frame

B41 080-7E41

B42 080-7E42 1 Bolt

B43 080-7E43 1 Rocker Arm

B44 080-7E44 1 Nut

B45 080-7E45 4 Tandem Load Roller - Polyurethane

– 080-7E45S 4 Tandem Load Roller - Steel

– 080-7E46Y 1 Touch-Up Paint Can - Yellow

– 080-7E101 4 Control Handle Spring

16 ISSUE DATE: JULY 13, 2016 REV.1 (PART # 038-697E)

 NX3000 HAND PALLET TRUCK—OPERATOR’S MANUAL

NOTES

ISSUE DATE: JULY 13, 2016 REV.1 (PART # 038-697E) 17

 Corporate 410 Admiral Blvd USA 6350 Burnt Poplar Road
Mississauga, ON, Canada L5T 2N6 Greensboro, NC 27409
t 905.457.3900 f 905.457.2313 www.bluegiant.com

If calling within North America: t 1.800.872.2583 f 1.888.378.5781 © Copyright Blue Giant Equipment Corporation 2017