On Common Ground

T-Frac System™ Catalog

www.teamoiltools.com
© 2012 TEAM Oil Tools. All rights reserved.
 www.teamoiltools.com
© 2012 TEAM Oil Tools. All rights reserved.
 On Common Ground

TABLE OF CONTENTS

Threaded Latch Anchor 1

RSB1 Retrievable Seal Bore Packer 2

RSB Hydraulic Setting Tool 3

Open Hole Centralizer 4

T-Port Frac Sleeve 5

I-Port Frac Sleeve 6

Pump-Out Cement Sleeve 7

I-Hydro Frac Sleeve 8

Hy-Rate Frac Sleeve 9

ORIO™ Toe Valve 10

GateWay™ Frac Sleeve 11

T-Pack HIP Packer 12

I-Pack Packer 13

Hydro-Pack Packer 14

I-Circulation Sub 15

Ball Launching System 16

For more information, go to TeamOilTools.com or call 281.602.7815

© 2012 TEAM Oil Tools. All rights reserved. 042512
T-Frac System™ On Common Ground

Threaded Latch Anchor Seal Assembly

The T-580 Threaded Latch Anchor Seal Assembly is used to make a connection or dis-connection
of the tubing string and the RSB-1 Retrievable Seal Bore Packer. The seal assembly is engaged
by set down weight and disengaged by applying and maintaining tension at the packer followed
by right hand rotation. Sealing options and material choices are available to enable operation at
10,000psi at temperatures up to 450°F in standard or sour service conditions.

features and benefits

 Optional thread connections available
 Metal goods available for H2S service
 Right-hand rotation with tension to release
 Pressure rating up to 10,000psi
 Wide range of seal materials available to suit any well conditions.

Thread Latch Anchor Seal Assembly

Size Max O.D. Min I.D. Upper thread latch thread Seal Product
Inches (mm) Inches (mm) Inches (mm) connection Type Type Number
Inches
5.122” -4 Special 90D Bonded
4.750 (120.65) 5.875 (149.23) 3.870 (98.30) 4.500” EU 8RD Box T580-74A-010
Ratchet Left-Hand Nitrile

For more information, go to TeamOilTools.com or call 281.602.7815

© 2012 TEAM Oil Tools. All rights reserved. Patents: www.teamoiltools.com/Innovation/TEAM-Patents 031512

1
T-Frac System™ On Common Ground

RSB1 Retrievable Seal Bore Packer

The T-1265 RSB1 is a Retrievable Seal Bore Packer designed for use in applications where a
long tailpipe assembly is required. It is set hydraulically using a model G Hydraulic Setting Tool
with appropriate Wireline Adapter Kit and once set does not require string weight or tension to
remain anchored. All the load bearing parts are designed to withstand high tensile loads and the
bidirectional slips prevent any movement of the tool. The packer is retrieved by a straight pull
shear release mechanism.

The packer has two seal bores in the standard 7” size, a full bore 4.00” (101.60mm) ID and an
upper seal bore ID of 4.75” (120.65mm) to accept an anchor seal assembly.

features and benefits

 Designed for use in vertical, deviated or horizontal well completions.
 Bi-directional slips which prevent movement after setting.
 An internal locking system maintains pack-off.
 Full bore ID matches tubing and extended tailpipe.
 Both setting pressure and shear release are field adjustable.
 Ideal for anchoring a liner in the T-Frac™ multi-zone stimulation system.
 Rated to 300°F and 10,000psi.

RSB1 Retrievable Seal Bore Packer

Size Casing Weight Max O.D. Min I.D. Product
Inches (mm) Range Inches (mm) Inches (mm) Number
lbs/ft (kg/m)
7.000 (177.80) 26.0-32.0 (38.69-47.62) 5.875 (149.23) 3.875 (98.43) T1265-74A-000
7.000 (177.80) 26.0-32.0 (38.69-47.62) 5.875 (149.23) 3.875 (98.43) T1265-74A-005
7.000 (177.80) 26.0-32.0 (38.69-47.62) 5.875 (149.23) 3.875 (98.43) T1265-74B-000
7.000 (177.80) 26.0-32.0 (38.69-47.62) 5.875 (149.23) 3.875 (98.43) T1265-74B-001

For more information, go to TeamOilTools.com or call 281.602.7815

© 2012 TEAM Oil Tools. All rights reserved. Patents: www.teamoiltools.com/Innovation/TEAM-Patents 031512

2
T-Frac System™ On Common Ground

RSB1 Hydraulic Setting Tool

The RSB1 Hydraulic Setting Tool is used to set the RSB/RSB-1 Packer as part of a standard
completion or a liner in the T-Frac™ System. Once on depth, a predetermined differential pressure
is applied against a plugging device below the tool such as a pump out plug, a wireline plug or a
ball dropped or pumped from surface to an integral ball seat. This shears screws which activates
a hydraulic chamber that strokes the RSB1 Setting Tool, engages the slips and energizes the
packing elements.
Once the RSB/RSB-1 Packer is set and tested the RSB1 setting tool is released by picking up the
setting string and maintaining tension while applying right hand rotation. Ports between the seals
of the setting tool ensure drainage while tripping out of the hole.

features and benefits

 Large internal bypass allows fluid to enter the workstring while running in.
 An Integral ball seat is available.
 The tool is self-draining when pulling out of hole to prevent pulling a wet string.
 Setting pressure is field adjustable.
 High tensile capacity allows running of long liners.
 Supplementary setting chambers can be added as an option.
 Standard top connection is an IF drill pipe box.
 Rated at 350°F and 10,000psi.

RSB1 Hydraulic Setting Tool

Size Max O.D. Min I.D. Setting Product
Inches (mm) Inches (mm) Inches (mm) ball size Number
Inches (mm)
7.000 (177.80) 5.880 (149.35) 1.750 (44.45) 2.000 (50.80) T1062-70A-000

For more information, go to TeamOilTools.com or call 281.602.7815

© 2012 TEAM Oil Tools. All rights reserved. Patents: www.teamoiltools.com/Innovation/TEAM-Patents 031512

3
T-Frac System™ On Common Ground

Open Hole Centralizer

The Team Oil Tools Open Hole Centralizer is used with the Hydro-Pak and I-Pack Packers with
the open hole T-Frac System™. The centralizer protects the packer from damage during
installation in the open hole section of the well bore and swivels to allow for rotation when
running in the hole.

features and benefits

 Available in composite or steel
 Helps prevent running damage
 Centralizes when setting
 Swivels
 Pressure rating up to 10,000psi

Open Hole Centralizer

Size Max O.D. Min I.D. Product
Inches (mm) Inches (mm) Inches (mm) Number
7.000 (177.80) 5.812 (147.62) 4.000 (101.60) T117-74C-000
7.000 (177.80) 5.812 (147.62) 4.000 (101.60) T117-74B-000

For more information, go to TeamOilTools.com or call 281.602.7815

© 2012 TEAM Oil Tools. All rights reserved. Patents: www.teamoiltools.com/Innovation/TEAM-Patents 031412

4
T-Frac System™ On Common Ground

T-Port Frac Sleeve

The T1041 T-Port Frac Sleeve is designed for use in selective stimulation of multi-zone wells
in open hole or cemented completion applications, especially with the T-Frac™ system. It is
activated by circulating a ball to a drillable seat inside the tool, when hydraulic pressure is
applied from surface the differential pressure created across it shears the inner sleeve piston,
moving it downwards to open up the frac ports. The inner sleeve piston is locked in the full
open position by a ratchet ring, allowing stimulation of the zone.
The T-Port Frac Sleeve can be run in multiple quantities with each having a different ball and
seat size with the smallest on bottom and progressively larger sizes moving up the hole.

features and benefits

 Allows independent stimulation of 24 zones for the 4.500” tool and 31 zones for the 5.500”
tool when used in conjunction with the TEAM Hydro-Pack Packer or ORIO™ Hydro Port.
 The internal locking mechanism ensures that the frac ports remain fully open once the
sleeve is activated.
 The ball seat is drillable resulting in a full bore ID matching the pipe size.
 Once activated, the ball and seat act as a bridge plug preventing any communication to
lower zones.
 Available in seat ID’s accommodating setting ball sizes from 1” to 4.75”.
 Available in materials suitable for standard or sour service.
 Rated at 350°F and 10,000psi.

T-Port Frac Sleeve

Size Max O.D. Min I.D. Length Product
Inches (mm) Inches (mm) Inches (mm) Inches (mm) Number
4.500 (114.30) 5.635 (143.13) 3.895 (98.93) 29.00 (736.59) T1041-46A-000
5.500 (139.70) 6.750 (171.45) 4.495 (114.17) 25.00 (635.00) T1041-56A-000

For more information, go to TeamOilTools.com or call 281.602.7815

© 2012 TEAM Oil Tools. All rights reserved. Patents: www.teamoiltools.com/Innovation/TEAM-Patents 031312

5
T-Frac System™ On Common Ground

I-Port Frac Sleeve

The T1021 I-Port Frac Sleeve is designed for use in selective stimulation of multi-zone wells
in open hole or cemented completion applications, especially with the T-Frac™ system. It
is activated by circulating a ball to a drillable seat inside the tool, when hydraulic pressure
is applied from surface the differential pressure created across it shears the inner sleeve
piston, moving it downwards to open up the frac ports. The inner sleeve piston is locked in the
full open position by a ratchet ring, allowing stimulation of the zone.
The I-Port Frac Sleeve can be run in multiple quantities with each having a different ball and
seat size with the smallest on bottom and progressively larger sizes moving up the hole.

features and benefits

 Available in sizes 2-7/8”, 3-1/2” and 4-1/2”.
 The internal locking mechanism ensures that the frac ports remain fully open once the
sleeve is activated.
 The ball seat is drillable resulting in a full bore ID matching the pipe size.
 The shear pressure setting is field adjustable.
 Once activated, the ball and seat act as a bridge plug preventing any communication to
lower zones.
 Available in seat ID ranging from 0.786” to 3.536” accommodating setting ball sizes from
1” to 3.75” in increments of 0.25”.
 CCan be run in quantities of 5 for 2-7/8’, 6 for 3-1/2” and 12 for 4-1/2”.
 Available in materials suitable for standard or sour service.
 Rated up to 300°F and 10,000psi.

I-Port Frac Sleeve

Size Max O.D. Min I.D. Product
Inches (mm) Inches (mm) Inches (mm) Number
2.875 (73.03) 4.281 (108.74) 2.470 (62.74) T1021-25B-000
3.500 (88.90) 4.625 (117.48) 2.997 (76.12) T1021-35B-000
4.500 (114.30) 5.688 (144.48) 4.000 (101.60) T1021-45B-000

For more information, go to TeamOilTools.com or call 281.602.7815

© 2012 TEAM Oil Tools. All rights reserved. Patents: www.teamoiltools.com/Innovation/TEAM-Patents 031512

6
T-Frac System™ On Common Ground

Pump Out Cement Sleeve

The T218 Pump Out Cement Sleeve is a hydraulically operated sliding sleeve which is run as an
integral part of a casing string, to provide access to the annulus for use in Multi zone stimulation
operations. The device allows cement to be placed in the annulus above a specific point. It can be
opened to allow cement placement, then closed off externally and the operating pistons pumped to
bottom leaving a full ID without any drill out.

features and benefits

 Allows cement placement at a specific point in the annulus as required.
 Opened by casing pressure applied against a ball and seat.
 Closed by running a standard plug behind the cement.
 The closing sleeve is externally mounted.
 After closing the inner pistons and stop ring can be sheared out and pumped to bottom.
 After shear out a full ID remains without the need to drill out.

Pump Out Cement Sleeve

Size Max O.D. Min I.D. min i.d. MIN i.d. required Product
Inches (mm) Inches (mm) before after below tool Number
Inches (mm) Inches (mm) Inches (mm)
2.375 (60.33) 3.121 (79.27) 0.985 (25.02) 1.925 (48.90) 1.995 (50.67) T218-20A-000
2.875 (73.03) 3.766 (95.66) 1.234 (31.34) 2.400 (60.96) 2.441 (62.00) T218-25A-000
3.500 (88.90) 4.515 (114.68) 1.235 (31.37) 2.906 (73.81) 2.992 (76.00) T218-35A-000
4.500 (114.30) 5.500 (139.70) 1.234 (31.34) 3.970 (100.84) 4.000 (101.60) T218-45A-000
5.500 (139.70) 6.000 (152.40) 1.250 (31.75) 4.965 (126.11) 5.000 (127.00) T218-55A-000

For more information, go to TeamOilTools.com or call 281.602.7815

© 2012 TEAM Oil Tools. All rights reserved. Patents: www.teamoiltools.com/Innovation/TEAM-Patents 031512

7
T-Frac System™ On Common Ground

I-Hydro Frac Sleeve

The T1016 I-Hydro Frac Sleeve is designed for use in the selective stimulation of multiple
zone wells in any application such as a T-Frac™ operation, be it in open hole or cemented
completion and in vertical, high angle or horizontal wells. It is normally used as the lowermost
sleeve in a well equipped with multiple ball actuated frac sleeves. It is activated by circulating
a ball into a drillable seat located below the sleeve and applying hydraulic pressure from
surface which shears the piston free and drives it down to the fully open position where it is
locked in place by means of a snap ring.

features and benefits

 When opened, the sleeve is locked in the full open position to ensure that the flow area is
maximized at all times..
 The setting pressure for opening the sleeve can be readily field adjusted.
 The sleeve is available with a steel inner sleeve if drill out is not required or with a readily
drillable cast iron sleeve which results in a full bore ID when drilled out.
 Rated up to 300°F and 10,000psi.
 Available in materials to suit standard or sour service.

I-Hydro Frac Sleeve

Size Max O.D. Min I.D. Product
Inches (mm) Inches (mm) Inches (mm) Number
3.500 (88.90) 5.500 (139.70) 2.970 (75.44) T1016-36A-000
4.500 (114.30) 5.500 (139.70) 2.970 (75.44) T1016-45A-000

For more information, go to TeamOilTools.com or call 281.602.7815

© 2012 TEAM Oil Tools. All rights reserved. Patents: www.teamoiltools.com/Innovation/TEAM-Patents 031512

8
T-Frac System™ On Common Ground

HyRate Frac Sleeve

The T1024 HyRate Frac Sleeve is a hydraulically operated sleeve which, when mounted on the
casing string of a multi zone completion, provides a method of establishing communication
from the casing to the formation for treating purposes. It is activated by setting a bridge
plug inside the sleeve and then applying hydraulic pressure to the casing string to shift
the inner sleeve down and open up the communication ports. As an alternative the sleeve
has an internal profile which allows it to be opened mechanically using a HyRate Shifter in
applications where this method is preferable.

features and benefits

 Full open ID matching the casing provides for maximum flow rate.
 Following activation the inner sleeve is locked in place in the full open position.
 Full opening design allows its use in both open hole and cemented casing applications.
 Rated to 300°F and 10,000psi.
 Standard threads are LTC box and pin but can the tool be made available with any
required thread specifications for either standard or sour service.

HyRate Frac Sleeve

Size Max O.D. Min I.D. Product
Inches (mm) Inches (mm) Inches (mm) Number
4.500 (114.30) 6.000 (152.40) 3.845 (97.66) T1024-45B-000

For more information, go to TeamOilTools.com or call 281.602.7815

© 2012 TEAM Oil Tools. All rights reserved. Patents: www.teamoiltools.com/Innovation/TEAM-Patents 041612

9
T-Frac System™ On Common Ground

ORIO ™ Toe Valve

The T1026 ORIO™ Toe Valve “Patent Pending” is a hydrostatic operated sliding sleeve which is
run at the bottom of a cemented casing completion in horizontal wells and provides a means of
establishing circulation to facilitate subsequent treatment operations, such as “Plug and Perf.” Its’
unique design ensures that the sleeve, once activated, is always fully open as opposed to standard
shear sleeves which tend to open only partially when activated. This is achieved by hydrostatic
pressure always being applied across the sleeve against an atmospheric chamber.

features and benefits

 Equipped with a rupture disc which allows for pressure testing of the casing in excess of
15,000-psi.
 No moving parts on both the inside and outside of the valve. This is achieved with a unique
patented inner piston design.
 The design incorporates a dual rupture disk phased 180 degrees apart.
 The opening piston is hydraulically balanced while running in the hole.
 Once the rupture disc has burst and the shear screws sheared, hydrostatic pressure
continues to drive the sleeve fully open and maintains it there, by acting against an
atmospheric chamber, allowing maximum flow area throughout.
 Shouldered connections allow rotation while running in the hole or during cementing.
 Temperature Rating 350°F.
 Rupture Disc sizes up to 20,000-psi.

Maximum Surface Testing Pressure

Calculation
True Vertical Depth x 0.052 x Mud Weight = BHP
8,000 ft x 0.052 x 9 ppg = 3,744 psi
Rupture Disk - BHP = Maximum Surface Test Pressure
20,000 psi - 3,744 psi = 16,256 psi

ORIO™ Toe Valve

Size Max O.D. Min I.D. Length Pressure Rating Product
Inches (mm) Inches (mm) Inches (mm) Inches (mm) Pressure psi (bar) Number
3.500 (88.90) 4.40 (111.76) 1.80 (45.72) 37.20 (944.88) 22,000 (1516.85) T1026-35D-000
4.500 (114.30) 5.63 (143.00) 2.50 (63.50) 38.00 (925.20) 22,000 (1516.85) T1026-45D-000
5.500 (139.70) 6.75 (171.45) 3.00 (76.20) 42.00 (1066.80) 22,000 (1516.85) T1026-55D-000
5.500 (139.70) 7.38 (187.45) 4.25 (107.90) 42.00 (1066.80) 15,000 (1034.21) T1026-55C-000

For more information, go to TeamOilTools.com or call 281.602.7815

© 2012 TEAM Oil Tools. All rights reserved. Patents: www.teamoiltools.com/Innovation/TEAM-Patents 053112

10
T-Frac System™ On Common Ground

Gateway™ Frac Sleeve

The T1172 Gateway™ Frac Sleeve is a ball activated device designed for use in the T-Frac
System™ to facilitate the establishment of communication from the casing string to the
formation in multi zone open hole completions, especially horizontals. Once the ball has been
deployed and the sleeve shifted open by application of surface pressure, the ball remains
on seat and thereby creates a bridge plug between each zone. After all the zones have been
treated, the balls can all be flowed out of the well and if desired the seats can be drilled out in
order to provide maximum internal diameter throughout. This drill out also facilitates re-
entering the well with a Gateway shifter assembly to shift any given sleeve open or closed as
needed. The Gateway can also be configured without the ball seat sub for use in applications
where mechanical sleeve shifting is preferable.

features and benefits

 The unique design allows the perfect alignment of both sleeve and body flow ports thus
minimizing the pressure drop from casing to annulus.
 When shifted the piston remains locked in the open position
 Provides for rapid drill out of the ball seats.
 The sleeve can be operated open and closed by mechanical means after the seats have
been drilled out.
 Available with any specified thread connection and for either standard or sour service.
 Can be supplied with a Hyflow piston which incorporates multiple small diameter seats
and effectively increases the maximum flow rates for any given size. This is recommended
when a large number of sleeves is to be run in one well, in order to provide a maximum
pump thru capability.
 Rated at 300°F up to 10,000psi

Gateway™ Frac Sleeve

Size Max O.D. Min I.D. Product
Inches (mm) Inches (mm) Inches (mm) Number
3.500 (88.90) 5.625 (142.88) 3.063 (77.80) T1172-35C-000
4.500 (114.30) 5.625 (142.88) 3.718 (94.43) T1172-45B-000

For more information, go to TeamOilTools.com or call 281.602.7815

© 2012 TEAM Oil Tools. All rights reserved. Patents: www.teamoiltools.com/Innovation/TEAM-Patents 031412

11
T-Frac System™ On Common Ground

T-Pack HIP Packer

The T1019 T-Pack HIP Packer is Hydraulic Isolation Packer designed to be run in multiple
quantities, as an integral part of the casing string, for zonal isolation in multi-zone
completions such as in the T-Frac™ system. It can be run in either open or cased hole
completions and is suitable for application in vertical, high angle and horizontal wells. It
is a non-anchoring device set hydraulically by applying the required differential pressure
across a plug set below it. When set, it features an internal locking mechanism providing a
positive long term set and its’ durable construction makes it a viable alternative to the use of
inflatable packers.

features and benefits

 The outer components are locked in place to prevent premature setting during run in.
 Set by hydraulic pressure from surface against a plug located below the packer(s).
 Packing element set by a single acting setting piston.
 The setting pressure is field adjustable.
 Can be supplied with premium elastomers and in materials for sour service
applications.
 ID is compatible with the casing on which it is run.
 Compact design makes for ease of handling.
 Standard tool burst and collapse rating designed to be compatible with P-110 grade
casing.
 Offered with an HNBR element.
 Rated up to 350°F and 10,000psi.

T-Pack HIP Packer

Size Max O.D. Min I.D. open hole range Length Product
Inches (mm) Inches (mm) Inches (mm) Inches (mm) Inches (mm) Number
4.500 (114.30) 5.635 (143.13) 3.900 (99.06) 6.12-6.50 (155.6-165.1) 32.00 (812.80) T1019-46A-000
5.500 (139.70) 6.750 (171.45) 4.600 (116.84) 7.75-8.75 (196.9-222.3) 37.00 (939.80) T1019-56A-000

For more information, go to TeamOilTools.com or call 281.602.7815

© 2012 TEAM Oil Tools. All rights reserved. Patents: www.teamoiltools.com/Innovation/TEAM-Patents 041612

12
T-Frac System™ On Common Ground

I-Pack Packer

The T276 I-Pack Packer is designed to be run in multiple quantities, as an integral part of the
casing string, for zonal isolation in multi-zone completions such as in the T-Frac System™. It
can be run in either open or cased hole completions and is suitable for application in vertical,
high angle and horizontal wells. It is a non-anchoring device set hydraulically by applying the
required differential pressure across a plug set below it. When set, it features an internal
locking mechanism providing a positive long term set. It has two separate packing elements
for improved seal reliability and its durable construction makes it a viable alternative to the
use of inflatable packers.

features and benefits

 The outer components are locked in place to prevent premature setting during running in.
 The internal components are similarly locked.
 Set by hydraulic pressure from surface against a plug located below the packer(s).
 Both packing elements are set by a single acting setting piston.
 The setting pressure is field adjustable.
 Retrieved by straight pull shear release which is also field adjustable prior to run in if
required.
 Can be supplied with premium elastomers and in materials for sour service applications.
 ID is compatible with the casing on which it is run.
 Rated up to 300°F and 10,000psi.

I-Pack Packer
Size Max O.D. Min I.D. Product
Inches (mm) Inches (mm) Inches (mm) Number
4.500 (114.30) 4.500 (114.30) 2.495 (63.37) T276-56B-000
7.000 (177.80) 5.750 (146.05) 3.781 (96.04) T276-74E-000
7.000 (177.80) 7.875 (200.03) 3.995 (101.47) T276-74B-000
7.875 (200.25) 7.375 (187.33) 3.995 (101.47) T276-84A-000

For more information, go to TeamOilTools.com or call 281.602.7815

© 2012 TEAM Oil Tools. All rights reserved. Patents: www.teamoiltools.com/Innovation/TEAM-Patents 031512

13
T-Frac System™ On Common Ground

Hydro-Pack Packer

The T275 Hydro-Pack Packer is a hydraulic set anchor packer designed specifically for use in
the T-Frac™ system for multi-zone horizontal completions. It is mainly used as the top packer
to anchor the casing string at the heel of the well, but in longer liners it can also be used in
open hole at the toe for the same purpose. It is similar in construction to the T276 Iso-Pack
packer in that all components are locked together to prevent the possibility of presetting due to
drag while running in. It is set by the application of the required differential pressure across a
plug set below it.

features and benefits

 All components are locked in place to prevent premature setting during run in.
 Set by hydraulic pressure from surface against a plug located below the packer.
 The setting pressure is field adjustable.
 Retrieved by straight pull shear release.
 Rated at 10,000-psi working pressure and 300°F.
 Can be supplied with premium elastomers and in materials for sour service applications.
 The ID is compatible with the casing on which it is run.

Hydro-Pack Packer
Size Max O.D. Min I.D. Product
Inches (mm) Inches (mm) Inches (mm) Number
7.000 (177.80) 5.750 (146.05) 3.781 (96.04) T275-73A-000
7.000 (177.80) 5.750 (146.05) 3.781 (96.04) T275-73A-020
7.000 (177.80) 5.750 (146.05) 3.781 (96.04) T275-74E-000
7.000 (177.80) 5.750 (146.05) 3.781 (96.04) T275-74E-020
7.000 (177.80) 5.750 (146.05) 3.781 (96.04) T275-74B-000
7.000 (177.80) 5.750 (146.05) 3.781 (96.04) T275-74B-020
7.875 (200.25) 7.375 (187.33) 3.995 (101.47) T275-84A-020

For more information, go to TeamOilTools.com or call 281.602.7815

© 2012 TEAM Oil Tools. All rights reserved. Patents: www.teamoiltools.com/Innovation/TEAM-Patents 031512

14
T-Frac System™ On Common Ground

I-Circulation Sub

The T1073 I-Circulation Sub is designed for use in the multi stage T-Frac™ system in open hole
completions in vertical, high angle or horizontal applications. It is normally run as the lowest
seating sub and is run in the open position to enable circulation to be established at any time
during the running of the casing. Once the casing is at setting depth a ball is circulated onto the
seat and the internal sleeve is sheared free by the application of a predetermined pressure from
surface. It shifts down closing off the circulating ports and latching in place using a positive
locking mechanism. The casing string is thus prepared for the hydraulic completion processes
and fracturing operations that will follow.

features and benefits

 Readily adjustable closing pressure.
 When closed the internal locking mechanism is unaffected by pressure changes.
 Standard ball and seat sizes are 0.75” (19.05mm.) and 1” (25.4mm.) but this can be customized
if needed.
 Available in materials suitable for standard or sour service.
 Rated for high pressure applications.

I-Circulation Sub
Size Max O.D. Min I.D. TEMP. Rating Pressure Rating Product
Inches (mm) Inches (mm) Inches (mm) °F (°C) Pressure psi (bar) Number
2.875 (73.03) 4.281 (108.74) 0.750 (19.05) 300 (148.89) 10,000 (689.48) T1073-25B-000
3.500 (88.90) 5.400 (137.16) 0.750 (19.05) 300 (148.89) 10,000 (689.48) T1073-36A-000
4.500 (114.30) 5.400 (137.16) 4.000 (101.60) 300 (148.89) 10,000 (689.48) T1073-45A-000

For more information, go to TeamOilTools.com or call 281.602.7815

© 2012 TEAM Oil Tools. All rights reserved. Patents: www.teamoiltools.com/Innovation/TEAM-Patents 031512

15
T-Frac System™ On Common Ground

Ball Launching System

The T-Frac™Ball Launching System is compactly designed high pressure device

used in multi-zone fracturing operations such as the T-Frac System™. It provides an
automated launching process to speed up and eliminate errors in the process for
launching operating balls into the well undergoing treatment. It can handle a total
of 6 separate balls in sequence and if more are required the units can be readily
stacked as required. Each ball is launched remotely using a proven quarter turn
pneumatic actuator operated from a self-contained control panel. The ball launcher
incorporates both a flag indicator to give visual indication of launching and a manual
override should it be required.

features and benefits

 The wellhead connection uses a proprietary lubricator style system for fast
manual installation.
 Units are stackable and incorporate a unique quick connect wellhead connection.
This provides the choice of stacking units if more than 6 balls are involved for fast
rig up of a second preloaded unit if preferred.
 The unit is easily redressed in the field if needed.
 Balls are top loaded and are set up ahead of time to function for all the launching
required.
 Each ball is separately launched by a field proven 1/4 turn pneumatic actuator.
 Shouldered connections allow rotation while running in the hole or during
cementing.
 Control of the unit is provided from a remote self-contained pneumatic control
panel linked to the actuators by a pneumatic umbilical.
 Balls are launched by a pneumatic signal to the 1/4 turn actuator which rotates
the “spoon” allowing the ball to fall while maintaining full ID when fully actuated.
 The flag on each actuator provides visual verification of launch.
 Wrench flats at the flag can be used for manual actuator override.

Ball Launcher System

Length MIN O.D. Min I.D. ball Ball Size Pressure Rating Product
Inches (mm) Inches (mm) Inches (mm) capacity Inches (mm) Pressure psi (bar) Number
1.000-4750
55.000 (1397.00) 12.000 (304.80) 5.000 (127.00) 6 15,000 (1397.00) T191400
(25.40-120.65)

For more information, go to TeamOilTools.com or call 281.602.7815

© 2012 TEAM Oil Tools. All rights reserved. Patents: www.teamoiltools.com/Innovation/TEAM-Patents 031312

16
 www.teamoiltools.com
© 2012 TEAM Oil Tools. All rights reserved.
 www.teamoiltools.com
© 2012 TEAM Oil Tools. All rights reserved.
On Common Ground

www.teamoiltools.com
© 2012 TEAM Oil Tools. All rights reserved.