KIT INSTRUCTIONS
RealPOS XR7 Integration Tray
7702-K304
Issue D
The product described in this book is a licensed product of NCR Corporation.
NCR is a registered trademark of NCR Corporation. NCR RealPOS is a trademark of NCR Corporation in the United States
and/or other countries. Other product names mentioned in this publication may be trademarks or registered trademarks of their
respective companies and are hereby acknowledged.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks
of HDMI Licensing LLC in the United States and other countries.
Where creation of derivative works, modifications or copies of this NCR copyrighted documentation is permitted under the terms
and conditions of an agreement you have with NCR, NCR's copyright notice must be included.
It is the policy of NCR Corporation (NCR) to improve products as new technology, components, software, and firmware become
available. NCR, therefore, reserves the right to change specifications without prior notice.
All features, functions, and operations described herein may not be marketed by NCR in all parts of the world. In some instances,
photographs are of equipment prototypes. Therefore, before using this document, consult with your NCR representative or NCR
office for information that is applicable and current.
To maintain the quality of our publications, we need your comments on the accuracy, clarity, organization, and value of this book.
Please use the link below to send your comments.
EMail: FD230036@ncr.com
Copyright © 2014–2018
By NCR Corporation
Duluth, GA U.S.A.
All Rights Reserved
Revision Record
Issue Date Remarks
A Jun 2014 First Issue
B Mar 2016 Tray Support Bracket changed from 497-0507954 to 497-0511268
C Feb 2018 Added 7199 Printer
D June 2018 Removed 7459-K316 Printer Skirt
RealPOS XR7 Integration Tray
Introduction
The Integration Tray kit provides the necessary components for integrating a printer,
keyboard, and Customer Display with the RealPOS XR7 terminal. It can be mounted on
a flat surface or on a cash drawer.
2 RealPOS XR7 Integration Tray Kit Instructions
Components
RealPOS XR7 Integration Tray Kit Instructions 3
Installation Procedures
The Integration Tray can be installed on an NCR 2181 Cash Drawer or it can be installed
directly onto a counter top.
Installing on a Cash Drawer
1. Position the Tray Support Bracket on a Cash Drawer and secure it using the supplied
screws (4).
Note: The mounting holes for the 3rd-party mount much be located toward the
rear of the unit.
2. Position the Integration Tray on top of the Tray Support Bracket and secure it with
screws (4).
4 RealPOS XR7 Integration Tray Kit Instructions
Installing on a Counter Top
1. Position the Tray Support Bracket on the counter top and secure it with screws (4)
that are appropriate for the surface type.
Note: The mounting holes for the 3rd-party mount much be located toward the
rear of the unit.
2. Position the Integration Tray on top of the Tray Support Bracket. Secure the tray to
the Tray Support Bracket with screws (2). Secure the front of the tray to the counter
top with screws (2) that are appropriate for the surface type
RealPOS XR7 Integration Tray Kit Instructions 5
Installing the Keyboard
Note: If a keyboard is not used, insert the Integration Tray Plug into the opening
where the keyboard cable would normally be routed.
1. Install the keyboard in the Integration Tray.
2. Route the cable through the opening in the Integration Tray. It will be routed up
through the XR7 Mount later when the XR7 is installed.
Compact Keyboard: Install the Keyboard Tray Insert beside the keyboard.
Note: There are two Keyboard Tray Inserts. The narrow tray is used in all cases except
when using the 5932 65xx PS/2 model without an MSR.
6 RealPOS XR7 Integration Tray Kit Instructions
Installing the Transaction Printer
The NCR 7167, 7168, 7197, 7198, or 7199 printer can be located on either side of the
Integration Tray.
Note: The Printer Cable Strain Relief is different on the Release 1.0 and the Series II
printers. The Cable Strain Relief on Release 1.0 printers prevents the printer from sitting
properly in the Integration Tray and must be removed from the printer and installed in
the Integration Tray.
NCR 7167/7168 Release 1.0 Printers Only:
1. Remove the Cable Strain Relief from the back of the printer (2 screws). The printer
will not sit properly in the tray with it installed.
2. Install the Cable Strain Relief on the Integration Tray using the same screws.
RealPOS XR7 Integration Tray Kit Instructions 7
3. Connect the Printer Cable to the USB and Power connectors.
4. Series II Printers Only: Route the cable through the Cable Strain Relief on the
printer as shown.
8 RealPOS XR7 Integration Tray Kit Instructions
5. Route the printer cable through the openings in the Integration Tray as shown below
and then position the printer in the tray. It will be routed up through the XR7
Mount later when the XR7 is installed.
NCR 7197/7198/7199 Only: Install the 7607-K324 Printer Skirt.
NCR 7167/7168 Release 1.0 Printers Only: Secure the cable in the Cable Strain Relief
in the Integration Tray as shown.
RealPOS XR7 Integration Tray Kit Instructions 9
Installing the LCD Customer Display
1. Secure the Operator Display Base to the Tray Support Bracket with screws (4).
Note: A Filler Cap is available for when there is no Customer Display
2. Install the Display Arm onto the Display Base.
10 RealPOS XR7 Integration Tray Kit Instructions
3. Install the Display Back Plate onto the back of the Customer Display (4 screws).
RealPOS XR7 Integration Tray Kit Instructions 11
4. Insert the Display Back Plate into the Operator Display Arm.
Cable Routing
The exploded view below shows how to route the cables up through the display mount.
5. Remove the excess slack in the cables and then install the Display Swing Arm Cover
onto the Display Swing Arm.
6. Connect the cables to the display. See the NCR RealPOS X-Series Displays User Guide
(B005-0000-2337) for additional information about cable connections.
NCR RealPOS X-Series Displays I/O Panel
12 RealPOS XR7 Integration Tray Kit Instructions
Installing the 2x20 Customer Display
1. Install the Customer Display Base with screws (4). Install the post behind or in front
of the Operator Display Arm.
Note: A Filler Cap is available for when there is no Customer Display
2. Connect the Interface Cable to the Display Module. This can be done without
removing the Back Cabinet.
RealPOS XR7 Integration Tray Kit Instructions 13
3. Route the display cables down through the Customer Display Base and out the back
of the cabinet.
4. Route the cable through the Display Swivel and Post.
14 RealPOS XR7 Integration Tray Kit Instructions
5. Insert the Display Post into the Customer Display Base.
RealPOS XR7 Integration Tray Kit Instructions 15
Installing the RealPOS XR7 POS Terminal
The Operator Display can be installed on the front or back on either side of the tray.
1. Separate the 7702-K303 Mount Base of the Display Arm (unscrew Clamp Knob).
16 RealPOS XR7 Integration Tray Kit Instructions
2. Install the Mount Base in the Integration Tray (4 screws).
3. Remove the Left Pivot Housing and Right Pivot Housing from the Display Arm
(1 screw on each).
RealPOS XR7 Integration Tray Kit Instructions 17
4. Lay the RealPOS XR7 fase down on a protective cloth/foam.
5. Install the Display Arm onto the back of the RealPOS XR7 (4 screws). Install the
VESA Plate between the mount and the terminal.
6. Install the teminal and Display Arm assembly onto the Mount Base and secure it
with the Mount Washer and Mount Knob.
18 RealPOS XR7 Integration Tray Kit Instructions
7. Replace the Left and Right Pivot Housings.
8. Connect the peripheral, LAN, and power cables to the terminal.
Cable Routing
The exploded view below shows how to route the cables through the display mount.
RealPOS XR7 Integration Tray Kit Instructions 19
Installing the Swing Arm Skirts
1. Install the Left Swing Arm Skirt.
2. Align the Right Swing Arm Skirt with the Left Swing Arm Skirt and snap it into
position.
20
