An instruction manual

Liquid Crystal Image Finder

Model AK-HVF100MC

Before operating this machine, please read this manual carefully and keep it properly
for future use. Before using this product, please read "please read this section first!"
(Page 2).

SS1215HM1066-YI CHINESE
Printing in Japan, issued: June VQT5M24-1
2016
Please read this section first!

Please read this section first!

Show security information.

Warning: Note:
f in order to reduce the fire hazard, do not let the Do not open the panel cover.
machine be exposed to rain or place it in a There are no parts that users can repair. For
damp place. maintenance problems, please contact qualified
f to reduce the risk of fire, please avoid all use of maintenance personnel.
this equipment. Liquid occasions, and can only Note:
be stored in places where there is no danger of In order to reduce the risk of fire and annoying
dripping or splashing liquid, and do not place interference, please use only the accessories of
Warning: the recommend.
Accessories (camera number table) must be Note:
placed out of reach of infants and children. In order to maintain good ventilation conditions,
please do not install or place the machine in
bookcases, wall cabinets or other sealed spaces.
Make sure that curtains or other fabrics do not
hinder ventilation conditions and prevent fire due

Name and content of harmful substances in products

Armful
Part name substance
Hexavalent Polybrom Polybromina
Lead(Pb) Mercury( Cadmium
Hg) (Cd) chromium inated ted diphenyl
(Cr (Ⅵ)) biphenyl ether
(PBB) (PBDE)
Appearance ○ ○ ○ ○ ○ ○
Circuit board X ○ ○ ○ ○ ○
Wire rod X ○ ○ ○ ○ ○
LCD part X ○ ○ ○ ○ ○
Basis of this form the provisions of SJ/T 11364.
○ : indicates that the content of the harmful substance in all homogeneous materials of the component is the
limits specified in GB/T 26572 are as follows.
X: indicates that the content of the harmful substance in at least one homogeneous material of the component
exceeds limits specified in GB/T 26572.

LCD screen
Due to the characteristics of the liquid crystal monitor, displaying bright still images for a long time or operating
in high temperature or high humidity environment for a long time may lead to residual images, brightness
reduction, aging, banded or panel defects and degradation that cause permanent changes in the brightness of
some areas.
In particular, the following types of images should be avoided for a long time.
f bright still image
f an image containing a logo or graphic with a fixed position
f computer window or similar bright display
f images with different aspect ratios and camera aspect ratios (e.g., umbrella images).
In addition, long-term continuous use in the following types of environments should also be avoided.
f narrow areas with high temperature and humidity
f near the air outlet of air conditioning equipment
In the case of the above images and environment, long-term use will lead to accelerated degradation of the LCD panel.
To prevent accelerated degradation and other related phenomena, we recommend the following operations:
f do not display bright still images for a long time.
f turn down the brightness.
2
f turn off the power when the monitor is not used.
The remaining images will gradually disappear as different images are displayed.

3
 f the names, company names and product names listed in this document are trademarks or registered trademarks of
the corresponding company.
How to read this document?

r figure
f illustrations may differ from actual products.

r usage regulations in this manual

f the text in [] indicates the content displayed on the screen.
f brackets the words in <> indicate the design text used by the camera, such as the button name, etc.

r reference Page
f the reference page in this document 00 pages).

4
Catalog

Catalog
Please read this section first! 2
Before using the camera 5
Characteristic 6
Enclosure 6
Parts description 7
Top 7
Last 8
Use external DC power supply 10
Get ready 11
Install to camera 11
Install shade 12
Tilt operation 13
Shake shooting operation 13
Lifting operation 14
On-screen display 15
Operation Status Display 15
Image adjustment knob status display 16
Function Display 16
Mode check Display 17
Camera menu display 18
Menu operation 19
Basic operation 19
Menu structure 21
Menu list 21
Maintenance and inspection 29
Specifications 30
Size 30
Specification 30
Connector pin allocation table 31

5
 Before using the
camera
Before using the
camera
r liquid crystal display
f liquid Crystal Display is manufactured by high-precision technology, with effective pixels exceeding 99.99%, but
there are still 0.01% of pixels are missing or always bright (red, blue, green). This is normal, don't worry.
f the liquid crystal protection panel is specially processed. Wiping with a hard cloth or rubbing hard may scratch the
surface.
f the response speed and brightness of liquid crystal will change with the change of ambient temperature.

r handle
f do not let the equipment fall or cause strong impact or vibration to the equipment. Otherwise, the device may be
damaged.

r operating temperature range

f when used in the following occasions, the image quality may decrease or cause adverse effects
on internal components. Avoid using in such occasions. The temperature is low temperature
occasions of 0°C or below.
The temperature is high temperature occasions of 45°C or above.

r maintenance
f when cleaning the chassis and liquid crystal protection panel, gently wipe it with soft cloth.
If you need to remove stubborn stains, please use cloth to get the neutral weak detergent solution, and
then wring it thoroughly. Then wipe with dry cloth. If the liquid penetrates into the monitor, it will
cause damage to the Monitor.
f do not use alcohol, diluent or benzene to
clean the equipment. Otherwise, the surface
of the equipment may fade or fall off paint.
f do not spray the spray cleaner directly onto the monitor. If the liquid penetrates into the monitor, it will cause
damage to the Monitor.

r jt / disconnect connector
f make sure to turn off the power of the device before connecting or disconnecting the connector.

6
Characteristic

Characteristic
This equipment is equipped LCD imager with 9.0-inch LCD panel.
This equipment can be used as a portable video camera (AK-UC3000MC/AK-UC3000MS, AK-HC5000MC/
AK-HC5000MS, AK-HC2500MC/AK-HC2500MS, AK-HC3500AMC/AK-HC3500AMS). Install this device
AK-HC2500MC/AK-HC2500MS or when AK-HC3500AMC/AK-HC3500AMS, use external
DC power input.
Automatically distinguish the video signal format and display the video of the camera.
Regardless of the settings of the image finder in this equipment, various marks, focusing
auxiliary functions, waveform display functions, etc. can be set. These functions can be assigned
to the <F1>/<F2>/<F3>/<F4> button, and these functions can be displayed by pressing the
button.

Enclosure
Shade camera number table ( 1 to 12)

1234
5678
9 10 11 12

@ be careful
t after opening the product packaging, please handle the packaging materials correctly.

7
 部件说明

Parts description
Front
46768

110

11

12
213
314

56768

1 <〈 F1> 〉 /<〈 F2> 〉 /<〈 F3> 〉

/<〈 F4> button
Through [MAIN MENU] [FUNCTION][FUNCTION1] to [FUNCTION4] can assign a function to each
button.
Press the button to operate the function assigned to the button. For more information, see [FUNCTION]( no. 23
pages).
2 <〈 POWER> indicator light
This indicator light (green) is on when the power is turned on.
Set to [MAIN MENU] [SYSTEM CONFIG][POWER LED][OFF1]/[OFF2] is disabled.
3 <〈 POWER> switch
This switch is used to turn on /Turn off the power.
When the power is on, press this switch to turn off the power for two seconds or more.
4 Distributable TALLY indicator lamp
This light is based on [MAIN MENU] [SYSTEM CONFIG] the status set in [TALLY ASSIGN] is on.
Can Pass [MAIN MENU] [TALLY BRIGHT] [FRONT TALLY] [HIGH] [/ MID] LOW] switch
[/ brightness.
5 <〈 EXT> indicator light
This indicator light is on when you use the lens to increase the distance.
Can Pass [MAIN MENU] [TALLY BRIGHT] [FRONT TALLY] [HIGH] [/
MID] LOW] switch
6 Red TALLY indicator lamp
[/ brightness.
Enter Red this indicator light is on when the signal is forwarded.
Can Pass [MAIN MENU] [TALLY BRIGHT] [FRONT TALLY] [HIGH] [/
7 Green TALLY indicator lamp
MID] LOW] switch
Enter Green this indicator light is on when the signal is forwarded. [/ brightness.
Can Pass [MAIN MENU] [TALLY BRIGHT] [FRONT TALLY] [HIGH] [/
8 Yellow TALLY indicator lamp
Enter Yellow this indicator light is on when the signal is forwarded. MID] LOW] switch
Can Pass [MAIN MENU] [TALLY BRIGHT] [FRONT TALLY] [HIGH] [/ [/ brightness.
9 <〈 BRIGHT> Knob
This knob is used to adjust the brightness of the image.
10<〈 CONTRAST> Knob MID] LOW] switch
This knob is used to adjust the contrast of the image. [/ brightness.

7
Parts description

11<〈 PEAKING> Knob

This knob is used to adjust the contour correction of the image.
12<〈 SELECT> Shuttle button
This shuttle button is used for screen operation.
When the <SELECT> Shuttle button is rotated clockwise, the cursor will move downward. When the shuttle
button is rotated counterclockwise, the cursor will move upward.
To SELECT a menu item, press the <SELECT> Shuttle button.
Set to Pass [MAIN MENU] [FUNCTION][ASSIGN] the assigned function.
13<〈 ADJ> indicator light
This indicator light (green) is on during adjustment.
[FUNCTION]  when [ASSIGN] is set to any item except [UNDEF], this indicator light is on.
14<〈 MENU> button
This button is used to open /Close the menu.

@ be careful t when the setting of [FRONT TALLY] is changed, you can assign **indicator light/<EXT>
indicator light/Red** indicator light/Green**Indicator light/yellow** the brightness of the indicator light is
switched at the same time.

Back
5

6789

1 <〈 INPUT> switch

This switch is used to switch the input
(<CAM>/<SDI>). The following lists the
signal formats supported by each input.
f <〈 CAM>: 1080/59.94i, 1080/50I
f <〈 SDI>: 1080/59.94p, 1080/50p, 1080/59.94i, 1080/50I, 720/59.94p, 720/50p
2 <〈 SDI IN> terminal
This terminal input SDI signal.
3 Tilt friction Knob
This knob is used to adjust the operating torque of the tilt.
Marked on the knob 〈 > increase the operating torque when rotating.

8
 部件说明

4 <〈 DC IN> terminal

This terminal is the input terminal of the external DC power supply. This terminal is connected to an external DC
power supply. (DC 12 V)
When AK-UC3000MC/AK-UC3000MS or AK-HC5000MC/AK-HC5000MS when connecting to a device I/F
connector
Power supply. No input of external DC power supply is required.
When the external DC power supply is connected, the external DC power supply is used.
Install this device AK-HC2500MC/AK-HC2500MS or when AK-HC3500AMC/AK-HC3500AMS, you must use
DC power input.
5 Airward TALLY indicator lamp
This indicator light lights up with the control signal of the camera.
Can Pass [MAIN MENU] [TALLY BRIGHT] [UP TALLY] [HIGH]/[LOW]/[OFF] switching
brightness. Camera number table (attachment) can be installed.
6 Lifting friction Knob
This knob is used to adjust the operating torque of lifting.
Marked on the knob 〈 > increase the operating torque when rotating.
7 Video camera I /F connector
This terminal is used to connect the portable camera of the broadcasting studio (AK-UC3000MC/AK-
UC3000MS, AK-HC5000MC/ AK-HC5000MS, AK-HC2500MC/AK-HC2500MS, AK-
HC3500AMC/AK-HC3500AMS).
Install this device AK-HC2500MC/AK-HC2500MS or when AK-HC3500AMC/AK-HC3500AMS, you must use
DC power input.
8 Rocking lock Rod
This rod is used for locking /Unlock the camera. Move this lever to <LOCK> to LOCK, and move this lever to
the opposite direction to unlock.
9 Lifting lock knob
This rod is used for locking /Unlock the lift. Turn this knob to <LOCK> to LOCK, and turn this knob to the
opposite direction to unlock.

9
Use external DC power supply

Use external DC power supply

DC cable
External DC
power supply

<DC IN>
terminal

1 DC IN> The terminal is connected to the external DC power supply.

2 Turn on the external DC power supply 〈 POWER> switch (if the external DC power supply has <
〈 POWER> switch).
3 Power on the device.
r external DC power supply
Confirm that the output voltage of the external DC power supply is compatible with the rated voltage of the
equipment before connection.
The output current of the selected external DC power supply should be higher than the total current of the
connected equipment, leaving sufficient margin.
Inrush current will be generated when the power supply of this equipment is turned on. Failure may occur if the
power performance is insufficient when the power is turned on. It is recommended to use an external DC power
f make sure that the pin distribution of the DC output terminal of the external DC power supply is
consistent with that of the <DC IN> terminal of the equipment, and the polarity is correct during
connection. Error 12V power connection GND terminals may cause fire or failure.
DC IN
1 UNREG GND
14
2 Not used
23 3 Not used
4 12V
HA16RA-4P (77) (Hirose Electric Co.)

10
 准备

Get ready
Install to camera

Connector cover
V-shaped groove

V-shaped protrusion
Lock release button
Figure 1 Figure 2

1 Turn off the power of the camera and the equipment.

2 Press the lock release button on the camera to remove the connector cover. (Figure 1)
3 V shape protrusion and camera V align the slots and slide the device in and push it inward until it is
locked. (Figure 2)
By locking the rocking locking Rod and lifting friction knob on this equipment,
the installation and disassembly are easy. After the installation is completed,
confirm that the equipment has been firmly installed on the camera.

@ be careful
t do not hold the shade of this equipment during installation.
r disassemble
1 Turn off the power of the camera and the equipment.
2 Press the lock release button on the camera and slide and remove the device at the same time.
@ be careful
t do not hold the shade of this equipment when disassembling.

11
准备

Install the shade

Hanging Piece

Sl
ot

Figure 1 Figure 2

Scre
w

Figure 3

1 Hang the hanging piece of the shade on the top slot. (Figure 1 figure 2)
2 Use two screws to fix the bottom of the shade. (Figure 3)
r disassemble
1 Loosen the two screws at the bottom of the shade.
2 Pull the bottom of the hood forward slightly and then pull it out upward.

12
 准备

Tilt operation

Tilt friction
Knob

1 Turn the inclined friction knob to adjust to the appropriate torque.

Xiang 〈 > When rotating in the direction, the operating torque becomes larger.

2 Adjust the tilt.

@ be careful
t when adjusting the tilt, do not hold the shade of this equipment.

Shake camera operation

Rocking
lock Rod

1 Move the rocking lock lever to and 〈 LOCK> opposite direction.

After moving the rocking LOCK lever to the opposite direction of <LOCK>, the rocking operation can be
performed.
2 Adjust the angle.
If you need to fix it at any position, move the rocking locking rod to the direction of <LOCK>.

@ be careful
t please do not hold the shade of this equipment when adjusting the Shake shot.

13
准备

Lift operation
Lifting lock knob

Lifting friction
Knob

1 Turn the lifting lock knob 〈 LOCK> opposite direction.

After turning the lifting LOCK knob to the opposite direction of <LOCK>, the lifting operation can be carried
out. If you need to fix it at any position, turn the lifting LOCK knob to the direction of <LOCK>.
2 Turn the lifting friction knob to adjust to the appropriate torque.
Xiang 〈 > When rotating in the direction, the operating torque becomes larger.

3 Adjust and hold the position of the fixture.

@ be careful
t when adjusting the lifting, do not hold the shade of this equipment.

14
 屏幕上的显示

On-screen display
The operation status, function, image adjustment status and menu information are displayed on the screen.

Operation Status Display

a CAM 1080/59. 94i c
B FILM

a: input status
Displays the selected input line ([SDI] or [CAM]). ( no. 8 pages)
Through [MAIN MENU] [SYSTEM CONFIG][STATUS DISPLAY] set DISPLAY conditions.
B: movie mode display
Select [MAIN MENU] [VIDEO CONFIG][GAMMA SELECT][FILM], this mode is displayed.
c: signal format display
Display the input signal.
[ UNSUPPORT SIGNAL]: the input signal is not supported.
[ NO SIGNAL]: no signal is input.

@ be careful
t in [MAIN MENU][SYSTEM CONFIG] in [STATUS DISPLAY], you can set conditions for
STATUS DISPLAY. In factory settings, the status display disappears after three seconds.
t the display of [UNSUPPORT SIGNAL] and [NO SIGNAL] may be incorrect.

15
屏幕上的显示

Image adjustment knob status display

<BRIGHT> Knob

<CONTRAST> Knob

<PEAKING> Knob

[BRIGHT] 30

1 rotate <〈 BRIGHT> 〉 /<〈 CONTRAST> 〉 /<〈 PEAKING> knob.

The name and adjustment value of the operation knob are displayed.
f this display disappears after two seconds without any action.
f in the factory settings, the adjustment value is displayed in green.

Function display
<F1>/<F2>/<F3>/<F4> button

F1: MONO
F2: WFM
F3: FOCUS-IN-RED
F4: MARKER
MONO ON

1 按〈F1〉/〈F2〉/〈F3〉/〈F4〉按钮。
Displays the functions assigned to each button
and the status of the functions. f this display
disappears after two seconds without any
action.
f through [MAIN MENU][FUNCTION][FUNCTION DISPLAY] you can change the DISPLAY conditions.
f even if the power of the equipment is off, the function assigned to each button will remember the state before the
power is off. However,[FOCUS-IN-RED] and
[CAM MENU] will be restored to the disabled state.

16
 屏幕上的显示

Mode check Display

Displays the current setting status.
Perform the operation when the menu is not displayed.
[MODE CHECK]
BRIGHTNESS 30
CONTRAST 50
PEAKING 15
BACKLIGHT 100

INPUT SELECT CAM

INPUT FORMAT 1080i 59.94

FUNCTION1 MONO
FUNCTION2 WFM
FUNCTION3 FOCUS-IN-RED
FUNCTION4 MARKER

ASSIGN UNDEF

TALLY ASSIGN OFF

<SELECT> Shuttle
button

1 press <〈 SELECT> Shuttle button.

The setting status is displayed.
The display will disappear after about two minutes without any operation.
f [BRIGHTNESS]: use <BRIGHT> the value of knob
adjustment. f [CONTRAST]: The value adjusted by using the
<CONTRAST> knob. f [PEAKING]: The value adjusted by
using the <PEAKING> knob.
f [BACK LIGHT]: passed [MAIN MENU][VIDEO CONFIG] the value set by [BACK LIGHT].
f [INPUT SELECT]: the INPUT selected by the <INPUT> switch.
f [INPUT FORMAT]: the current INPUT video signal FORMAT.
f [FUNCTION1]: The function assigned to the
<F1> button. f [FUNCTION2]: The function
assigned to the <F2> button. f [FUNCTION3]: The
function assigned to the <F3> button. f
[FUNCTION4]: The function assigned to the <F4>
button.
f [ASSIGN]: The function assigned to the <SELECT> Shuttle button.
f[TALLY ASSIGN]: passed [MAIN MENU][SYSTEM CONFIG][TALLY ASSIGN] set lighting
condition.

17
屏幕上的显示

Camera menu display

The camera can be operated from this equipment (only AK-UC3000MC/AK-UC3000MS and AK-HC5000MC/AK-
HC5000MS).
<F1>/<F2>/<F3>/<F4> button

F1: MONO
F2: WFM
F3: FOCUS-IN-RED
F4: CAM MENU
CAM MENU ON

<SELECT> Shuttle
button

<MENU> button

1 Through [ MAIN MENU] [ FUNCTION] [ FUNCTION1] /[ FUNCTION2] /[ FUNCTION3]

/[ FUNCTION4] will [ CAM MENU] Set to <〈 F1> 〉 /<〈 F2> 〉 /<〈 F3> 〉 /<〈 F4>.
2 By set [ CAM MENU] 〈 F1> 〉 /<〈 F2> 〉 /<〈 F3> 〉 /<〈 F4> button.
3 Press <〈 MENU> button.
The menu screen of the camera will be displayed.
4 Rotate <〈 SELECT> Shuttle button, select the project.
5 Press <〈 SELECT> Shuttle button.
For information on menu operation methods, please refer to the operating instructions of the camera.

@ be careful
t the [CAM MENU] setting will be cleared after the power is turned off.

18
 菜单操作

Menu operation
Describes the menu operation method, the structure of the setting menu, and the details of the setting menu.

Basic operations
<SELECT> Shuttle button [MAIN MENU]
MARKER
FUNCTION
VIDEO CONFIG
SYSTEM CONFIG
HOURS METER
UP TALLY FOCUS
ASSIST

Figure 1

[MARKER]
EXIT
MARKER OFF
ZONE 4:3
4:3 OFF
BACK NORMA
CENTER L
CROSS HATCH OFF
SIZE OFF
BOX MARKER 120
TYPE OFF
H POS BOX
V POS 960
<MENU> button H SIZE 540
V SIZE 700
700

Figure 2

1 Press <〈 MENU> button.

[MAIN MENU] is displayed. ( image 1)
Set [MAIN MENU] [SYSTEM CONFIG][MENU RESUME] after [ON], press the <MENU> button to
display the previous MENU.
[MAIN MENU] is displayed when the power is turned on again after the power is turned off.
2 Rotate <〈 SELECT> Shuttle button, select menu item.
3 Press <〈 SELECT> Shuttle button.
The selected item appears. (Figure 2)
4 Rotate <〈 SELECT> Shuttle button, select the project to be set.
5 Press <〈 SELECT> Shuttle button.
The value changes to green.
6 Rotate <〈 SELECT> Shuttle button, change the settings.
To cancel, press the MENU button.
7 Press <〈 SELECT> Shuttle button.
The settings are confirmed.

@ be careful
t this display will disappear after two minutes without any action. When the display disappears, the display value is
confirmed as the set value.

19
菜单操作

[ ASSIGN] settings ([ ASSIGN] status display)

<SELECT> Shuttle button

[FOCUS-IN-R] 15
<MENU>
button

1 Through [ MAIN MENU] [ FUNCTION] [ ASSIGN] Select 〈 SELECT> the function of shuttle
button allocation.
2 Press <〈 SELECT> Shuttle button.
3 Press <〈 MENU> button to close the menu.
4 Rotate <〈 SELECT> Shuttle button, change the settings.
The function in progress and its adjustment value are displayed.
f this display disappears after two seconds without any action.

Key lock settings

You can disable the operation of the <F1>/<F2>/<F3>/<F4> button, the <SELECT> Shuttle button,
and the <MENU> button. The <POWER> button, <BRIGHT> knob, <CONTRAST> knob and
<PEAKING> knob cannot be disabled.
<F1>/<F2>/<F3>/<F4> button
(Key tag)

<SELECT> Shuttle button

<MENU> button

1 press <〈 SELECT> the shuttle button can display the mode check screen, and then press <〈 MENU>
button for three seconds or more.
When the key is locked, the key mark is always displayed in the upper-left corner of the screen.
f the settings will be cleared after the power is turned off.
f to clear the key lock, press and hold the <MENU> button for three seconds or more.

20
 菜单操作

Menu structure

[MAIN MENU] [MARKER] Set the tag.

[FUNCTION] Set the <F1>/<F2>/<F3>/<F4> button operation. Set the screen.
[VIDEO
CONFIG] Configure the system.
[SYSTEM
CONFIG] Displays the running time and lighting time of the backlight.

[HOUR
Settings TALLY indicator light and front the brightness of the indicator light.
METER]
[TALLY
BRIGHT]
[FOCUS Set the focus auxiliary
Menu list ASSIST] function.

[ MARKER]

Project Settings
[EXIT] Returns the
previous level.
[MARKER] - Specifies whether to display a marker in the screen.
[ ON], [ OFF]
f factory settings:[OFF]
When [BOX MARKER] is set to [ON1]/[ON2] and [MARKER] is set to
[ON],[BOX MARKER] is set to [OFF].
Select the tag type.
[ZONE]
[ OFF]: No mark is displayed.
[ 4:3]:4:3 size mark.
[ 13:9]: Mark of size 13:9.
[ 14:9]:14:9 size mark.
[ CNSCO2.39]:2.39:1 size mark.
[ CNSCO2.35]:2.35:1 size mark.
[ 2:1]:2:1 size mark.
[ VISTA]:1.85:1 size mark.
[ 95%]: Mark of 95% area.
[ 93%]: The Mark of the 93% area.
[ 90%]: The Mark of the 90% area.
[ 88%]: The Mark of the 88% area.
[ 80%]: Mark the 80% area.
[ USER85%]:80% to 100% variable area mark (1% step) (press the
<SELECT> Shuttle button to set the value to light blue) (factory setting is
[85%])
f factory settings:[4:3]

21
菜单操作

Projec Settings
t Select aspect ratio the type of the tag
[4:3] displayed when 4:3.
[ OFF]: No mark is displayed.
[ 95%]: Mark of 95% area.
[ 93%]: The Mark of the 93% area.
[ 90%]: The Mark of the 90% area.
[ 88%]: The Mark of the 88% area.
[ 80%]: Mark the 80% area.
[ USER85%]:80% to 100% variable area mark (1% step) (press the
<SELECT> Shuttle button to set the value to light blue) (factory setting is
[85%])
f factory settings:[OFF]
[BACK] Set the background brightness outside the marker set in [ZONE].
[ NORMAL]: normal background.
[ HALF]: set the background brightness 50%.
[ BLACK]: set the background brightness 0%(black).
f factory
settings:[NORMAL]
[CENTER]
specifies whether to display
the central mark.
[CROSS [ ON], [ OFF]
-
HATCH] f factory settings:[OFF]
Sets the display and density of section lines.
[ OFF]: not displayed.
[ LOW]: displays a dim section line.
[ HIGH]: Display a bright section line.
[SIZE] f factory settings:[OFF]
select the section line
size.
[ 60]:60 points and points 60 rows
[BOX [ 120]:120 points and points 120 lines
-
MARKER]
f factory settings:[120]
Specifies whether to display box marks in the screen. Two patterns, [ON1] and
[ON2], can be recorded.
[ ON1], [ ON2], [ OFF]
f factory settings:[OFF]
[TYPE]
When [MARKER] is set to [ON] and [BOX MARKER] is set to
[ON1]/[ON2],[MARKER] is set to [OFF].
Sets the display type of the box mark.
[ BOX]: box type display.
[H POS] [ CROSS]: Cross type display.
f factory settings:[BOX]
Sets the horizontal position of the display box mark.
[V POS] [ 10] ...[ 1910](10-point step)
f factory settings:[960]
Sets the vertical position of the display box mark.
[H SIZE] [ 10] ...[ 1070](10 steps)
f factory settings:[540]
Set the horizontal dimension of the box mark.
[ 10] ...[ 1910](10-point step)
f factory settings:[700]

22
 菜单操作

Proje Settings
ct
[V SIZE] Sets the vertical dimension of the box mark.
[ 10] ...[ 1070](10 steps)
f factory settings: [700]

[ FUNCTION]

Project Settings
[EXIT] Returns the
previous level.
[FUNCTION1] Select the function assigned to the <F1> button.
[ SCAN]: switch between underscan and normal display.
[ WFM]: Display the waveform display screen.
[ MARKER]: Display the tag.
[ FOCUS-IN-RED]: switch to enable /Disable the image focus part lifting
function (Display
Disable when [WFM], disable when there is no input signal, clear the
setting when the power is off, use [MAIN MENU] during operation
[FUNCTION][ASSIGN] assigned
[FOCUS-IN-RED], the detection sensitivity can be changed through the
<SELECT> Shuttle button).
[ CROSS HATCH]: switch the section line display.
[ MONO]: switch between color and monochrome display.
[ UP TALLY]: On / close Up **Indicator light.
[ FRONT TALLY]: switch forward the brightness of the indicator light.
[ CAM MENU]: Enable /Disable the camera menu operation function
(clear the setting when the power is off).
[ FOCUS ASSIST]: Enable /Disable the focus auxiliary function on the
camera.
[ ZOOM LINK]: Enable /Disable the detail function associated with zoom on
the image finder.
[ UNDEF]: The function is not assigned.
f factory settings:[MONO]
[AK-UC3000MC], [AK-UC3000MS] and [AK-HC5000MC] can be
operated only when connecting the camera (AK-HC5000MS/CAM MENU,
FOCUS ASSIST/)
[ZOOM LINK].

23
菜单操作

Project Settings
[FUNCTION2] Select the function assigned to the <F2> button.
[ SCAN]: switch between underscan and normal display.
[ WFM]: Display the waveform display screen.
[ MARKER]: Display the tag.
[ FOCUS-IN-RED]: switch to enable /Disable the image focus part lifting function
(Display
Disable when [WFM], disable when there is no input signal, clear the
setting when the power is off, use [MAIN MENU] during operation
[FUNCTION][ASSIGN] assigned
[FOCUS-IN-RED], the detection sensitivity can be changed through the <SELECT>
Shuttle button).
[ CROSS HATCH]: switch the section line display.
[ MONO]: switch between color and monochrome display.
[ UP TALLY]: On / close Up **Indicator light.
[ FRONT TALLY]: switch forward the brightness of the indicator light.
[ CAM MENU]: Enable /Disable the camera menu operation function
(clear the setting when the power is off).
[ FOCUS ASSIST]: Enable /Disable the focus auxiliary function on the camera.
[ ZOOM LINK]: Enable /Disable the detail function associated with zoom on the
image finder.
[ UNDEF]: The function is not assigned.
f factory settings:[WFM]
[AK-UC3000MC], [AK-UC3000MS] and [AK-HC5000MC] can be
operated only when connecting the camera (AK-HC5000MS/CAM MENU,
[FUNCTION3] FOCUS ASSIST/)
[ZOOM LINK].
Select the function assigned to the <F3> button.
[ SCAN]: switch between underscan and normal display.
[ WFM]: Display the waveform display screen.
[ MARKER]: Display the tag.
[ FOCUS-IN-RED]: switch to enable /Disable the image focus part lifting function
(Display
Disable when [WFM], disable when there is no input signal, clear the
setting when the power is off, use [MAIN MENU] during operation
[FUNCTION][ASSIGN] assigned
[FOCUS-IN-RED], the detection sensitivity can be changed through the <SELECT>
Shuttle button).
[ CROSS HATCH]: switch the section line display.
[ MONO]: switch between color and monochrome display.
[ UP TALLY]: On / close Up **Indicator light.
[ FRONT TALLY]: switch forward the brightness of the indicator light.
[ CAM MENU]: Enable /Disable the camera menu operation function
(clear the setting when the power is off).
[ FOCUS ASSIST]: Enable /Disable the focus auxiliary function on the camera.
[ ZOOM LINK]: Enable /Disable the detail function associated with zoom on the
image finder.
[ UNDEF]: The function is not assigned.
f factory settings:[FOCUS-IN-RED]
[AK-UC3000MC], [AK-UC3000MS] and [AK-HC5000MC] can be
operated only when connecting the camera (AK-HC5000MS/CAM MENU,
FOCUS ASSIST/)
[ZOOM LINK].

24
 菜单操作

Project Settings
[FUNCTION4] Select the function assigned to the <F4> button.
[ SCAN]: switch between underscan and normal display.
[ WFM]: Display the waveform display screen.
[ MARKER]: Display the tag.
[ FOCUS-IN-RED]: switch to enable /Disable the image focus part lifting
function (Display
Disable when [WFM], disable when there is no input signal, clear the
setting when the power is off, use [MAIN MENU] during operation
[FUNCTION][ASSIGN] assigned
[FOCUS-IN-RED], the detection sensitivity can be changed through the
<SELECT> Shuttle button).
[ CROSS HATCH]: switch the section line display.
[ MONO]: switch between color and monochrome display.
[ UP TALLY]: On / close Up **Indicator light.
[ FRONT TALLY]: switch forward the brightness of the indicator light.
[ CAM MENU]: Enable /Disable the camera menu operation function
(clear the setting when the power is off).
[ FOCUS ASSIST]: Enable /Disable the focus auxiliary function on the
camera.
[ ZOOM LINK]: Enable /Disable the detail function associated with zoom on
the image finder.
[ UNDEF]: The function is not assigned.
f factory settings:[MARKER]
[AK-UC3000MC], [AK-UC3000MS] and [AK-HC5000MC] can be
[ASSIGN] operated only when connecting the camera (AK-HC5000MS/CAM MENU,
FOCUS ASSIST/)
[ZOOM LINK].
SELECT the function assigned to the <SELECT> Shuttle button when the
menu is not displayed.
[ FOCUS-IN-RED]: change the focus part of the image to improve the
detection sensitivity of the function.
[ IN-RED-COLOR]: switch the display color of the image focus part to
improve the function.
[ BACK LIGHT]: change the brightness of the LCD backlight.
[ VF DTL]: adjust the detail level of the image finder.
[ MARKER BACK]: switch to [MAIN MENU][MARKER]
The background brightness outside the marker set in [ZONE].
[ BOX MARKER VF]: Enable /Disable the display of box marks on this
device.
[ BOX MARKER CAM]: Enable /Disable the display of frame marks on the
camera.
[FUNCTION DISPLAY] [ ZOOM LINK LEVEL]: switch the level of detail associated with the zoom
of the image finder.
[ UNDEF]: The function is not assigned.
f factory settings:[UNDEF]
[AK-UC3000MC], [AK-UC3000MS] and [AK-HC5000MC] can be
operated only when connecting the camera (AK-HC5000MS/VF DTL,
BOX MARKER CAM/)
[ZOOM LINK LEVEL].
Select the display settings and Operation settings (one touch, two touch)
of the function assigned to the <F1>/<F2>/<F3>/<F4> button.
[ OFF]: This function is not displayed.
[ ON1]: displays the function while setting the operation. (One Touch)
[ ON2]: Display the function first, and then set the operation by pressing
the <F1>/<F2>/<F3>/<F4> button. (Two touches)
25
菜单操作
f factory settings:[ON1]

[ VIDEO CONFIG]

Proje Settings
ct
[EXIT] Returns the previous level.

26
 菜单操作

Project Settings
[GAMMA- Select the gamma curve.
SELECT] [ STANDARD]: Standard mode.
[ FILM]: FILM mode ([FILM] is displayed in the upper left corner of the picture).
f factory settings:[STANDARD]
[FILM Select the type of movie gamma mode according to the gamma setting of the
GAMMA] camera.
[ FILM REC]: when [FILM REC] is selected.
[ OTHER]: when selecting any project except [FILM REC].
Gamma curve
diagram

[OTHER]
Brightness[FILM REC]

[STANDARD]

Input
level

f factory settings:[FILM REC]

[COLOR TEMP.]
select the color temperature.
[ USER 0] ...[ USER 63]: variable settings 0 to 63(Equivalent to color temperature
3000 K
To 9300 K)(it can be set when the <SELECT> Shuttle button is pressed, and the
setting value changes to light blue).
[ D93]: equivalent to color temperature 9300 K
[ D65]: equivalent to color temperature 6500 K
[ D56]: equivalent to color temperature 5600 K
[SHARPNESS MODE]
f factory settings:[D65]
Select the edge width of contour correction (peak period).
[ HIGH]: Narrow Edge
[ LOW]: wide edge
[SHARPNESS H] f factory settings:[HIGH]
set horizontal contour
correction.
The operation to add to the PEAKING knob.
[SHARPNESS V] [ 0]... [ 30]
f factory settings:[0]
set vertical profile
correction.
[MONO] The operation to add to the PEAKING knob.
[ 0]... [ 30]
f factory settings:[0]
Switch between color and monochrome.
[SCAN] [ OFF]: color.
[ ON]: monochrome.
f factory settings:[OFF]
Sets the underscan or normal display of the screen.
[ NORMAL]: normal display.
[BACK LIGHT] [ UNDER]: underscan.
f factory settings:[NORMAL]
adjust the brightness of the LCD
backlight.
[ 0]... [ 100]
f factory settings:[100]
27
菜单操作

[ SYSTEM CONFIG]

Project Settings
[EXIT] Returns the
previous level.
[WFM] Sets whether to display the waveform of the video signal input to the image
finder.
If [WFM] is displayed when [FOCUS-IN-RED] is enabled,
[FOCUS-IN-RED] will be disabled.
[ OFF]: not displayed.
[ WFM]: Display the waveform of the brightness signal.
f factory settings:[OFF]
[WFM POSITION] Select the position where the waveform is displayed when [WFM] is [ON].
[ LB]: the lower left corner of the screen.
[ RB]: the lower right corner of the screen.
[ RT]: the upper-right corner of the screen.
[ LT]: the upper-left corner of the screen.
f factory settings:[RB]
[TALLY ASSIGN] Set allocatable the lighting status of the indicator light.
[ OFF]: disabled.
[ INPUT SDI]: turn on when the INPUT switch is set to SDI.
[ INPUT CAM]: turn on when the INPUT switch is set to CAM.
[ CAM MENU]: open when the menu operation function of the
camera is enabled. Only when the camera is connected (AK-
UC3000MC/AK-UC3000MS, AK-HC5000MC/ AK-HC5000MS).
f factory settings:[OFF]
Enable /Disable menu restoration.
[MENU RESUME] [ OFF], [ ON]
f factory settings:[OFF]
Set the light status of the POWER indicator.
[POWER LED] [ ON]: continuously open.
[ OFF1]: off (when the power is off /When enabled, the settings will be
restored to [ON]).
[ OFF2]: continuously shut down.
f factory settings:[ON]
Set the display conditions for the status display.
[STATUS DISPLAY] [ CONTINUE]: continuous display.
[ 3SEC OFF]: after changing the status of the status display, it is displayed for
three seconds and then disappears.
[ OFF]: not displayed.
f factory settings:[3SEC OFF]

[ HOUR METER]

Proje Settings
ct
[EXIT] Returns the previous level.
[OPERATION] Displays the total number of hours of power on.
Up 262800 hours [262800 hours] ( make an appointment30 years).
Exceed the hours of 262800 hours are displayed as [OVER].
[LCD] The number of hours that the backlight is enabled.
Up 262800 hours [262800 hours] ( make an appointment30 years).
Exceed the hours of 262800 hours are displayed as [OVER].

28
 菜单操作

[ TALLY BRIGHT]

Project Settings
[EXIT] Returns the
previous level.
[UP TALLY] Set up the brightness of the indicator light.
[ HIGH]: open (bright).
[ LOW]: open (DIM).
[ OFF]: disabled.
f factory settings:[LOW]
Set forward the brightness of the indicator light.
[FRONT TALLY]
[ HIGH]: open (bright).
[ MID]: open (medium light).
[ LOW]: open (DIM).
f factory settings:[MID]

[ FOCUS ASSIST]

Project Settings
[EXIT] Returns the
previous level.
[FOCUS-IN-RED]- Enable /Disable the image focus enhancement function of this device.
This function is disabled when [WFM] is displayed. Disabled when there
is no input signal. (The settings will be cleared after the power is turned
off)
[ OFF], [ ON]
f factory settings:[OFF]
[IN-RED-COLOR] set the display color of the image focus part lifting function of this equipment.
[ RED], [ GREEN], [ BLUE], [ WHITE]
f factory settings:[RED]
[ZOOM LINK] - Enable /Disable the detail function associated with zoom on the image finder.
[ OFF], [ ON]
f factory settings:[OFF]
Only when the camera is connected (AK-UC3000MC/AK-UC3000MS, AK-
HC5000MC/
AK-HC5000MS). Sets the level of
[LINK LEVEL]
detail associated with the image finder
and zoom.
[ LOW], [ MID], [ HIGH]
f factory settings:[LOW]
[FOCUS ASSIST] Enable /Disable the focus auxiliary function on the camera.
[ OFF], [ ON]
f factory settings:[OFF]
Only when the camera is connected (AK-UC3000MC/AK-UC3000MS, AK-
HC5000MC/
AK-HC5000MS).

29
 Maintenance
and inspection
Maintenanc
e and
inspection
Through regular and appropriate maintenance, maintenance and inspection are carried out to keep the functions
of the equipment in good condition, so that customers can safely use the equipment.
Ensure the maintenance and inspection of equipment functions to keep them in good condition for a long time.

r regular maintenance services

The LCD panel is equipped with backlight. Backlight is a lossy component, and its performance will gradually
decrease and will eventually fail.
Therefore, in addition to traditional maintenance in case of failure, regular maintenance services should also be
carried out. Maintenance service can keep equipment performance in good condition and avoid accidental
failure caused by damaged parts.

29
Specifications

Specifications
Size
231mm

340 mm 193 mm

234 mm

Specifications summary

Power consumption
Direct e12V ( by camera or XLR) power
consumption
Indicates security information.
18W
Ambient operating temperature 0°C - 45°C
Storage temp 20°C - 60°C
Ambient operating humidity 10% - 85% (No condensation)
Weight Make an appointment2.6 k] (Excluding shade)
Make an appointment3.0 k] (Including shade)
Size (width high long) 340 mm 234 mm 193 mm
(Excluding shade)
340 mm 234 mm 231mm
(Including shade)

30
 Specifications

Display panel

Size 9.0
Pixel number 1920 1080 (FHD)
Display color Make an appointment 16,770,000 colors

Switch function / connector

Operati <POWER> switch

on <MENU> button
<SELECT> Shuttle button
<F1>/<F2>/<F3>/<F4> button
<BRIGHT> Knob
<CONTRAST> Knob
<PEAKING> Knob
<INPUT> switch
Video camera I/F connector (D-sub 29 pin
1) SDI IN connector (BNC1)
Connec DC IN connector (XLR 4 pin 1)
tor

Supported signal formats

CAM 1080/59.94i, 1080/50I

SDI 1080/59.94p, 1080/50p, 1080/59.94i, 1080/50I
720/59.94p, 720/50p

Connector pin allocation table

Video camera I /F connector ( D-sub 29 pin)
1

11 20 29

1 Y 11 Y GND 21 Not used

2 PB 12 P B GND 22 Not used
3 PR 13 P R GND 23 Not used
4 CAM DET 14 Not used 24 I2C CLK
5 I2C DATA 15 DGND 25 G TALLY
6 R TALLY 16 Not used 26 P REQ
7 UP TALLY 17 UNREG-GND 27 Not used
8 VF12 V 18 Not used 28 Not used
9 VF12 V 19 FGND 29 Not used
10 VF12 V 20 (LCD ACT)
D02-29PF-N-F0 (Japan Aviation Electronics Industry)

31
Waste disposal information in other countries outside the EU
This symbol is valid only in the EU.
If you want to discard this product, please contact the local organization or distributor to obtain the
correct method of abandonment.

Panasonic Electric
Manufacturer:
Appliance
Japan Osaka Prefecture Industry Co.,
menzhen city
Ltd. 1006 website:
Daizi menzhen
http://www.panasonic.com
En th Merchant: Panasonic Electric (Middle
ter
m
ou
China) Co., Ltd.
Website on the 3rd and 6th floors, Block C, Yuanyang
Guanghua Center, No. 5, Jinghua South Street, Chaoyang
district, Beijing: http://panasonic.cn/
Origin: Japan, Ben
© Panasonic Electric Appliance Industry Co., Ltd. All rights reserved for 2016.

33