CT3200 Programmable Thermostat

OWNER’S GUIDE
Welcome to the world of comfort and energy savings with your
new Honeywell Programmable Thermostat. Your new thermostat
will automatically control the temperature in your home, keeping
you comfortable while saving energy.

Weekday/Weekend (5-day/2-day)
Programmable Heat and/or Cool
Low Voltage (20 to 30 Vac)
Thermostat and Mounting Plate
Model CT3200

Table of Contents
Installation .................................................................................................................................................................. 2
Programming.............................................................................................................................................................. 12
Operation.................................................................................................................................................................... 18
Frequently Asked Questions ...................................................................................................................................... 22
Customer Assistance ................................................................................................................................................. 23
Limited Warranty ........................................................................................................................................................ 24

® U.S. Registered Trademark

Copyright © 2003 Honeywell International Inc.
All Rights Reserved 69-1631-1
 MERCURY NOTICE
If you are removing an old thermostat that contains mercury in a sealed tube
(Fig. 1), do not place the old thermostat in the trash. Contact your local waste
management authority for instructions regarding recycling and the proper MERCURY
disposal of the old thermostat. SWITCH

M3701

Fig. 1.

INSTALLATION
Verify You Have Correct Thermostat
Make sure that the CT3200 is the correct thermostat for your heating/cooling system. Read the compatibility chart
below to determine which system you have. If your system is not compatible with the CT3200, the table recommends
an alternate Honeywell model. If you are unsure what type of thermostat is right for your system, visit us on the Web at
www.honeywell.com/yourhome or call Honeywell Customer Care at 1-800-468-1502.

Compatible
Heating/Cooling System with CT3200? Alternate Model
Conventional Yes
Single stage systems that include warm air furnaces and hot water.
Electric Baseboard No CT1950 for 240
Electric-powered heating strips located just above the floor, usually 120 to 240 volts
volts.

69-1631—1 2
 Compatible
Heating/Cooling System with CT3200? Alternate Model
Steam No CT3600
A steam boiler with radiator heat.
Heat Pump No CT3600
Heating and cooling are produced from the same outdoor unit (compressor) with
no auxiliary or backup heat.
Multistage Heat Pump No CT3611
Heating and cooling are produced from the same outdoor unit (compressor) with
auxiliary or backup heat.
Multistage Conventional No See your
A heating or cooling system with more than one stage. contractor

Step 1. Prepare for Installation

1. Carefully unpack your new thermostat. Save your receipt and make sure you have the following parts:
• Thermostat and mounting plate
• Labels
• Screws and anchors
• Installation and Programming Instructions
2. Gather the needed tools and supplies listed below.
Required Tools and Supplies Optional Tools
• Two AA alkaline batteries. Honeywell recommends Energizer® • Wire cutter/stripper or sharp knife.
batteries. • Level.
• Screwdriver. • Electrical tape.
• Hand or power drill with 3/16-inch or 7/32-inch drill bit.
• Pencil.
3. Make sure that your heating and cooling systems are working properly. If there is a problem with either system,
call a heating/air conditioning contractor—the problem may persist after you install the new thermostat.

IMPORTANT:
To avoid damaging the compressor in the air conditioner, do not operate the cooling system when the tem-
perature outdoors is below 50°F (10°C).

3 69-1631—1
Step 2. Remove Old Thermostat

Fig. 2. a. Turn off power to the heating/cooling system, either at the

furnace or at the fuse/circuit breaker panel.
b. Remove the cover of your old thermostat (Fig. 2).
c. Unscrew and remove the old thermostat’s mounting plate
from the wall, but do not disconnect the wires.
d. Inspect the old thermostat wiring. If wiring meets any of
the following conditions, see special wiring instruc-
M20140
tions section after Step 7.

Fig. 3. • The old thermostat is a clock thermostat with wires attached

to the C or C1 terminals.
• The old thermostat has six or more wires, excluding wires
attached to C or C1 terminals.
• The old thermostat has three wires.
• There are five wires connected to the old thermostat.
• There are extra wires that are not connected to the old
thermostat.
e. Using enclosed labels, mark wires with letter of terminal it is
attached to on the old thermostat (Fig. 3). Do not label
using colors. If labels do not match letters on old thermostat
terminals, see wiring cross reference table in Special Wiring
Instructions section.
M19086

Fig. 4. f. Disconnect the wires from the old thermostat and wrap the
WIRES THROUGH wires around a pencil to keep them from falling back into the
WALL OPENING wall.

NOTE: Remember, if your old thermostat contains mercury,

you must recycle it. See Mercury Notice for more
recycling information.

M20133 ✓Check your progress

Your wall should now look like Fig. 4.
69-1631—1 4
Step 3. Install Mounting Plate

Fig. 5. a. Separate the mounting plate from the thermostat using a

coin, as shown in Fig 5.
b. Position the mounting plate on the wall. Be sure the mount-
ing plate is flush against the wall and none of the wires are
trapped behind it.
c. Level the mounting plate and use a pencil to mark the cen-
ter of the mounting plate screw holes.
d. Remove the mounting plate and drill holes at the locations
marked.
M20139
• For drywall, drill two 3/16-inch holes.
• For plaster or wood, drill two 7/32-inch holes.

Fig. 6. e. If installing in drywall, gently tap the anchors (provided) into

the drilled holes until they are flush with the wall.
f. Reposition the mounting plate over the holes, pull the wires
through the wiring opening, and loosely insert the mounting
screws into each of the drilled holes or anchors (Fig. 6).
g. Make sure the mounting plate is level and tighten the
mounting screws.

M20129

Fig. 7. ✓ Check your progress

The mounting plate is now mounted on the wall and should look like
Fig. 7.

W
R
Y
Rc

M20128
G

5 69-1631—1
Step 4. Set Thermostat for Your Type of Heating System
THERMOSTAT BACK I IMPORTANT:
M Setting your thermostat correctly
ON
P for your type of heating system
1
DISPLAY F 3 - ON
2
1
2 O allows it to maintain accurate
DISPLAY C 3 - OFF
3 3 HEATING
SYSTEM
RDIP SWITCH FUEL SWITCH temperature control, minimize
POSITION POSITION
OFF ON WARM AIR T1 - ON 2 - ON F
swings in the temperature of the
FURNACE
HOT WATER OR
A room, and efficiently run the fan.
HIGH EFFICIENCY N 1 - OFF 2 - ON F
ELECTRIC
FURNACE T1 - ON 2 - OFF E
a. Use the FUEL SWITCH on the
W Y G : back of the thermostat to set your
new thermostat for the type of fuel
that your heating system uses: F–
gas or oil, or E–electric.
FUEL SWITCH W Y G
C R RC
F E NOTE: This setting enables
C RC proper fan operation.

b. Use DIP switches 1 and 2 on

M20637 the back of the thermostat to set
Fig. 8. your new thermostat for your type
of heating system. See the Heat-
ing System Table on the next
page to find the correct settings.

NOTE: These DIP switches are

factory-set for a warm air, gas, or
oil heating system.

c. The thermostat is set to display the temperature in degrees Fahrenheit (°F). If you want to display the tem-
perature in degrees Celsius (°C), turn DIP Switch 3 to Off position.
d. You can install the batteries and program your thermostat now, or you can wait until the thermostat is
mounted on the wall. To install the batteries, see Step 7.To program the thermostat, see the Programming
section.

69-1631—1 6
Heating System Table
DIP Switches
Type of System 1 and 2 Fuel Switch
Warm air, gas, or oil heating system with an efficiency rating under 90%. Use factory setting F
(The furnace efficiency rating should be on the furnace.) 1–On; 2–On
High-efficiency furnace such as a 90% or greater AFUE (Average Fuel 1–Off; 2–On F
Utilization Efficiency) unit
Hot water boiler 1–Off; 2–On F
Electric furnace 1–On; 2–Off E

Step 5. Wire Thermostat Terminals

Fig. 9. a. Hold thermostat as shown in Fig. 9.

b. Using the labels on the wires, match letter of your old ther-
mostat wire with the corresponding terminal on the back of
G
Y
your new thermostat.
W
R

NOTE: If letters on old thermostat terminals do not match letters on

new thermostat terminals, all old wires may not need con-
necting to new thermostat. See Special Wiring Instructions
section.

M20125

Fig. 10. c. Loosen terminal screws and slip each wire beneath its
matching terminal (Fig 10).
INSERT
STRAIGHT
d. Securely tighten terminals.
5/16 in.
UNDER
(8 mm)
SCREW HEAD
STRIP

END OF WIRE
VISIBLE HERE
M20126

7 69-1631—1
Step 6. Mount Thermostat

Fig. 11. Fig. 12. e. Align the tabs at the top of the thermostat
with the tabs at the top of the mounting
plate (Fig. 11).
f. Press the lower edge of the case to latch
the bottom of the thermostat (Fig. 12)

M20131
M20130

69-1631—1 8
Step 7. Install the batteries

Fig. 13. IMPORTANT:

Batteries must be installed for programming and operation of
the thermostat and heating/cooling system. Honeywell rec-
ommends using Energizer® batteries.

a. Make sure that the System switch is set in the OFF position.
b. Using a coin, open the battery door as shown in Fig. 13.
c. Install the batteries. Make sure that the positive and nega-
tive terminals are oriented correctly as marked inside the
REMOVING
battery case.
M1719C
BATTERY
DOOR
d. Replace the battery door.
e. Remove the clear plastic label from the digital display.
Fig. 14.
✓ Check your progress
When the batteries are installed correctly, the digital display flashes all
entries once, then begins to flash a default time and the current
temperature (Fig. 14). The flashing continues until you begin to
program the thermostat. You are now ready to program the thermostat.
See Programming section.

Special Wiring Instructions

Clock thermostat with C or C1 terminals
A clock thermostat has one or two extra wires attached to the C or C1 terminals that allow the clock to operate. These
wires are not used during the installation of your new 3200 Thermostat and must be insulated from each other to avoid
damaging your electrical circuit.

a. Make sure that power to the heating/cooling system is turned off.

b. Locate the wires that are connected to the clock terminals marked C or C1.
c. As you disconnect the wires, do not allow these wires to touch.
d. Wrap the wires separately, using electrical tape to insulate the wires.
e. Place the wires where they do not interfere with the operation of the new thermostat.
You will not connect these wires to your 3200 Thermostat.
f. Continue with the installation.
9 69-1631—1
Six or more wires
If your old thermostat has six or more wires (excluding clock wires attached to the C or C1 terminals), your heating/
cooling system is most likely a variation of a heat pump or multistage system. Your 3200 Thermostat will NOT work
with such systems and should be returned to the place of purchase. See the thermostat compatibility table for
information about which programmable thermostat will work with your system.

Three thermostat wires

If you have three wires for heating only and can operate the fan using the fan ON switch, the 3200 Thermostat will
work with your system. Continue the installation procedure.

If you have a three-wire heating-only system and cannot operate the fan using the fan ON switch, the 3200
Thermostat will probably NOT work with your system. Contact your heating contractor for installation assistance.

Wires that are not connected to old thermostat

If there are extra wires that do not connect to your old thermostat, do not label them. You will not connect these wires
to your new thermostat. Tape off the wires individually with electrical tape and place them where they will not interfere
with the operation of the new thermostat. Continue the installation procedure.

Five wires connected to old thermostat

JUMPER (FACTORY- Your new thermostat has a factory-installed metal jumper between the R and Rc
INSTALLED). REMOVE
IF 5-WIRE SYSTEM
terminals (Fig. 15). Remove the jumper before wiring the R and Rc terminals.
Rc R

G Y W
M20127

Fig. 15.

Thermostat C Terminal
This thermostat does not use the C wiring terminal.

69-1631—1 10
Old thermostat terminals that do not match new thermostat terminals
Use the table below to wire the new thermostat.

Connect to New
Old Thermostat Thermostat
Terminal Terminal Description
R, RH, 4, V R* Power
Rc, R Rc* Power for cooling
W, W1, H W Heat
Y, Y1, M Y Cooling
G, F G Fan
O Do not continue Changeover in cool (O terminal) or changeover in heat (B terminal).
installation You have a single-stage heat pump or zoning system. Select an alternate
B
thermostat model.
C, X, B Do not connect Transformer common.
W2, H2 Do not continue Second stage heat (W2, H2) or second stage cooling (Y2).
installation. You have a multistage heating/cooling system. Select an alternate
Y2
thermostat model.

*Remove factory-installed jumper between R and Rc terminals in 5-wire systems.

11 69-1631—1
PROGRAMMING
Faceplate Illustration and Description
Descriptions
Fig. 16. 1 Fan switch–Selects automatic fan operation or fan on.
7 8
2 Set Schedule–Puts the thermostat into programming
mode.
6 AM
PM SET
9
3 Set Clock/Day–Sets the clock and day.
SYSTEM ON
5 10
MO TU WE TH FR SA SU
WAKE LEAVE RETURN SLEEP
TEMPORARY
4 Time Ahead and Back–Sets the time ahead and back.
4 11
Time Temp 5 Program periods–Current program period or period being
Set Run
programmed.
3 Ahead Warmer 12
clock/Day Program
6 Day of the week–Current day or day being programmed.
Set Hold
2
Schedule Back Cooler Temp
13 7 Time–Current time or program time.
8 Temperature–Room temperature or programmed
Fan System temperature.
1 14
Auto On Cool Off Heat
9 SYSTEM ON–An arrow displays when the heating/
M20141
cooling system is running.
10 TEMPORARY–An arrow displays when a temporary
override is made to the program.
11 Temp Warmer and Cooler–Sets the temperature warmer
and cooler.
12 Run Program–Returns thermostat to normal operating
mode
13 Hold Temp–Holds a selected temperature.
14 System switch–Selects Cool, Off, Heat.

69-1631—1 12
Step 1. Set Current Time and Day

a. Press once. Fig. 17.

The time is displayed (Fig. 17).

b. Press and hold or until the cur-

rent time is displayed.

c. Press again. Fig. 18.

The day is displayed (Fig. 18).

d. Press and hold or until the cur-

rent day is displayed.

e. Press once. Fig. 19.

The current time and day and the current tempera-
ture are displayed (Fig. 19).

Step 2. Learn About Programming Features

Your 3200 Thermostat allows you to program schedules for both a heating season and a cooling season.

• During the heating season, you will want to set the normal room temperature higher and the energy-saving
temperature lower.
• The reverse is true during the cooling season—the normal room temperature will be lower and the energy-saving
temperature higher.
For each season, you can set up to four program periods for the weekdays (Monday–Friday), and up to two program
periods for the weekends (Saturday and Sunday). The program periods are defined in the following table.
13 69-1631—1
 Program Period Description When Available
WAKE The time when you get up and get ready to leave your home. You can Weekdays and weekend
set the system at a comfortable temperature for this period.
LEAVE The time when you are regularly away from home. You can set up an Weekdays only
energy-saving temperature for this period.
RETURN The time between returning home and going to bed. You can set the Weekdays only
system at a comfortable temperature for this period.
SLEEP The time when you are sleeping. You can set up an energy-saving Weekdays and weekend
temperature for this period.

Programming Tips
• You do not need to program times and temperatures for all program periods.
If you decide not to program your thermostat, it automatically controls heating at 68°F (20°C), and cooling at 78°F
(26°C), 24 hours a day.

If you decide not to program weekend schedules, the temperature that is programmed for the weekday SLEEP
schedule remains in effect until the next program period, which begins on Monday morning.

• The temperatures cannot be set any higher than 88°F (31°C) or any lower than 45°F (7°C).
• When pressing the buttons, use the ball of your finger or a soft pencil eraser. Using sharp fingernails or pencil
points can damage the keypad.

• If you make an error at any time during programming, press . Then press until you reach the
program period you last programmed.

69-1631—1 14
Step 3. Program Heating Schedule
a. Write in the times and temperatures that you want to program for your heating schedule.
Program
Heating Schedule Period WAKE LEAVE RETURN SLEEP
Suggested Time 6:00 AM 8:00 AM 6:00 PM 10:00 PM
Settings
Temp 70°F (21°C) 62°F (16.5°C) 70°F (21°C) 62°F (16.5°C)
Weekday (Mon–Fri) Time
Temp
Weekend (Sat–Sun) Time
Temp

b. Set the System switch to HEAT. Fig. 20.

c. Press once.
A blank schedule is displayed (Fig. 20).

d. Set the Monday–Friday WAKE time by pressing Fig. 21.

or until the desired time is displayed (Fig. 21).

e. Set the Monday–Friday WAKE temperature by pressing

or until desired temperature is

displayed.

15 69-1631—1
 f. Press to display a blank schedule for the next Fig. 22.
program period (Fig. 22) and repeat steps d. through f. for
each weekday program period.

g. Press until the weekend schedule is displayed Fig. 23.

(Fig. 23).

h. Set the Saturday and Sunday WAKE time by pressing

or until the desired time is displayed.

i. Set the Saturday and Sunday WAKE temperature by Fig. 24.

pressing or until desired temperature

displays (Fig. 24).

j. Press again to display blank schedule for SLEEP

program period and repeat steps h. through j. to set pro-

gram.

k. Press to start the program.

69-1631—1 16
Step 4. Program Cooling Schedule
a. Write in the times and temperatures you want to program for your cooling schedule.
Program
Cooling Schedule Period WAKE LEAVE RETURN SLEEP
Suggested Time 6:00 AM 8:00 AM 6:00 PM 10:00 PM
Settings
Temp 78°F (25.5°C) 85°F (29.5°C) 78°F (25.5°C) 82°F (28°C)
Weekday (Mon–Fri) Time
Temp
Weekend (Sat–Sun) Time
Temp
b. Set the System switch to COOL.
c. Repeat steps 3c. through 3k. to program the weekday and weekend cooling schedule.

Step 5. Check System

Verify that your heating system works

a. Set the System switch to HEAT, and the Fan switch to Fig. 25.
AUTO.
b. Press until the setting is 10°F (6°C) above room
temperature (Fig. 25). Your heating system should start
and the fan should run after a short delay.

c. Press until the setting is 10°F (6°C) below room

temperature. Your heating system should shut off.

17 69-1631—1
Verify that your cooling system works
IMPORTANT:
To avoid damaging the compressor in the air conditioner, do not operate the cooling system when the tem-
perature outdoors is below 50°F (10°C).

d. Set the System switch to COOL, and the Fan switch to AUTO. Fig. 26.

e. Press until the setting is 10°F (6°C) below room tem-

perature (Fig. 26). Your cooling system and fan should start.

NOTE: When cooling setting is changed, thermostat can

delay up to five minutes before turning on air condi-
tioner. This delay protects the compressor.

f. Press until setting is 10°F (6°C) above room temper-

ature.Your cooling system and fan should stop.
g. Set the System switch to OFF and the Fan switch to AUTO.
The cooling system and fan should be off.

OPERATION
Change Clock for Daylight/Standard Time

a. Press once. The time is displayed.

b. Press and hold or until the correct time is displayed.

c. Press once. The current time and day and current temperature display.

69-1631—1 18
Set Fan and System Switches
The switches on the bottom of the thermostat faceplate control the operation of your fan and the heating and cooling
system. Set the Fan switch first and then set the System switch.

Switch Setting Result

Fan Auto A single-speed fan turns on automatically with the air conditioner or furnace.
A two-speed fan usually runs on high with the air conditioner and on low with the furnace.
Auto is the normal setting for most homes.
On The fan runs continuously. Use this setting for improved air circulation during special
occasions or for more efficient air cleaning.

NOTE: In a heat-only system, the fan runs continuously only if the fan wire has been con-
nected to the G terminal on the back of the thermostat.
System Cool The thermostat controls your air conditioning system.
Off Both the heating and air conditioning systems are off.
Heat The thermostat controls your heating system.

Replace Batteries
As the batteries run low, your thermostat shows the following in the digital display:
If you see: Batteries are: You should:
Flashing “bAt Lo” Low Replace the batteries as soon as possible, within the month.
Blank display Dead Replace the batteries immediately. Your heating/cooling system is not
operating.
a. Make sure that the System switch is set to the OFF position.
b. Open the battery door.
c. Press on the left side of the batteries to remove them.

NOTE: If new batteries are inserted within 20-30 seconds of removing old ones, reprogramming is not
needed. If display is blank, batteries are dead or incorrectly installed and reprogramming is needed.

19 69-1631—1
 d. Install new batteries. Make sure that positive and negative terminals are oriented as marked inside battery
case.
e. Close the battery door and set the System switch to HEAT or COOL.

NOTE: If “bAt Lo” continues to display after replacing the batteries, set System switch to OFF, insert batteries back-
ward, wait for five to ten seconds, and return batteries to correct orientation. Then reprogram.

IMPORTANT:
Replace batteries once a year to prevent heating/cooling system from shutting down due to lack of battery
power in thermostat. If leaving home for longer than a month, change batteries before leaving.

Override program settings

NOTE: Make sure the System switch is set to either HEAT or COOL before making any changes to the schedule.

Change the temperature temporarily Fig. 27.

Press or until the desired temperature is

displayed. An arrow is displayed, indicating that the change is
temporary (Fig. 27).

NOTE: A temporary change to temperature lasts for current

program period only. Heating/cooling schedule you
programmed resumes when next scheduled pro-
gram period is reached.To cancel temporary
change before next scheduled program period,

press .

69-1631—1 20
Hold a temperature indefinitely Fig. 28.
Use the Hold Temp feature when you want to maintain a
constant temperature indefinitely, such as when you go on
vacation.

a. Press . “HLd” is displayed (Fig. 28).

b. Press or until the desired temperature is displayed.

NOTE: To cancel the hold, press .

Check the current programmed temperature Fig. 29.

Press to display temperature programmed for current

program period. The SET indicator displays briefly along with the
programmed temperature (Fig. 29). The display then returns to the
room temperature.

Check programs

Press repeatedly to display the times and temperatures

that you programmed.

a. Press to resume the program

Cancel a program Fig. 30.

a. Press until the desired program is displayed

(Fig 30).

21 69-1631—1
 b. Press and simultaneously. Fig. 31.
A blank program schedule is displayed and the program
is canceled (Fig. 31).

Change a program permanently

Follow steps for programming heating schedule or programming
cooling schedule.

FREQUENTLY ASKED QUESTIONS

If... Then...
Display does not come on • Make sure the batteries are fresh and installed correctly.
• Set System switch to Off. Remove batteries and insert backward for five to
ten seconds to reset thermostat. Replace batteries correctly; display should
come on.
Temperature display does not go • Temperature limit setting is reached; range is 45°F to 88°F (7°C to 31°C).
lower than 45°F (7°C) or higher than
88°F (31°C) during programming.
Display shows flashing “bAt Lo.” • The batteries are low; replace them as soon as possible.
• If “bAt Lo” continues to display after replacing batteries, set System switch
to Off and insert batteries backward for five to ten seconds. Replace
batteries correctly; display should come on.
Temperature change occurs at wrong • Check program times for period in question. Be sure AM and PM
times indications are correct. Make sure current day and time are correct.
Reprogram if necessary.

69-1631—1 22
 If... Then...
Heating does not come on • Check that the System switch is set to Heat.
• Check the system fuse or circuit breaker and replace or reset if necessary.
• Check for correct wiring and good connections.
• If display is blank or displays “bAt Lo,” install fresh batteries.
• Allow time for the furnace to heat up and the fan to come on before
checking for heat at the register.
• If temperature setting is higher than current room temperature and
SYSTEM ON arrow is displayed, thermostat is operating correctly. Contact
heating contractor for assistance.
Cooling does not come on • Check that the System switch is set to Cool.
• Check the system fuse or circuit breaker and replace or reset if necessary.
• Check for correct wiring and good connections.
• If display is blank or says “bAt Lo,” install fresh batteries.
• The thermostat has a built-in time delay on cooling. Allow 5-10 minutes
after changing setting before air conditioner starts.
• If temperature setting is lower than room temperature and SYSTEM ON
arrow is displayed, thermostat is operating correctly. Contact ac contractor.
The house is too warm or too cool • Press RUN PROGRAM to check the current temperature setting.
• If desired, change the temperature setting.
Furnace cycles too often or system • Adjust the screws on the back of the thermostat.
cycle length is too short or too long
The thermostat current setting does • Plug the wiring hole in the wall behind the mounting plate with insulation to
not match the display temperature to prevent drafts that might adversely affect thermostat operation.
within plus or minus 1° • Be aware that it is normal for the current setting and the displayed room
temperature to differ on occasion.
• During recovery from setback or setup, setting and displayed room
temperatures can differ for up to 30 minutes after recovery period.

CUSTOMER ASSISTANCE
Visit us on the Web at www.honeywell.com/yourhome or call Honeywell Customer Care at 1-800-468-1502.
Before you call, please have the following information available:
— Thermostat model number and serial code (located under the battery cover).
— Type of heating/cooling system (hot water, warm air, oil, gas, etc.).
— Number of wires connected to the thermostat.

NOTICE: This equipment is a Class B digital apparatus, that complies with Canadian Radio Interference Regulations, CRC c.1374.
23 69-1631—1
LIMITED WARRANTY
Honeywell warrants this product, excluding battery, to be free from defects in workmanship or materials, under normal use and service,
for a period of one (1) year from the date of purchase by the consumer. If, at any time during the warranty period, the product is
defective or malfunctions, Honeywell shall repair or replace it (at Honeywell’s option) within a reasonable period of time.If the product is
defective,
(i) return it, with a bill of sale or other dated proof of purchase, to the retailer from which you purchased it, or
(ii) package it carefully, along with proof of purchase (including date of purchase) and a short description of the malfunction, and mail it,
postage prepaid, to the following address:
Honeywell Inc. USA Honeywell Canada:
Dock 4 — MN10-3860 Honeywell Limited/Honeywell Limitée
1885 Douglas Drive North 35 Dynamic Drive
Golden Valley, MN 55422-3992 Scarborough, Ontario M1V 4Z9
This warranty does not cover removal or reinstallation costs. This warranty shall not apply if it is shown by Honeywell that the defect or
malfunction was caused by damage which occurred while the product was in the possession of a consumer.
Honeywell’s sole responsibility shall be to repair or replace the product within the terms stated above. HONEYWELL SHALL NOT BE
LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES
RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER
FAILURE OF THIS PRODUCT. Some states do not allow the exclusion or limitation of incidental or consequential damages, so this
limitation may not apply to you.
THIS WARRANTY IS THE ONLY EXPRESS WARRANTY HONEYWELL MAKES ON THIS PRODUCT. THE DURATION OF ANY
IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
IS HEREBY LIMITED TO THE ONE YEAR DURATION OF THIS WARRANTY. Some states do not allow limitations on how long an
implied warranty lasts, so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may have other rights which vary from state to state.
If you have any questions concerning this warranty, please write Honeywell Customer Relations Center, 1985 Douglas Dr. N., Golden
Valley, MN 55422-3992, or call 1-800-468-1502. In Canada, write Retail Products ON30 Honeywell Limited/Honeywell Limitée, 35
Dynamic Drive, Scarborough, Ontario M1V 4Z9.

Automation and Control Solutions

Honeywell International Inc. Honeywell Limited-Honeywell Limitée
1985 Douglas Drive North 35 Dynamic Drive
Golden Valley, MN 55422 Scarborough, Ontario
M1V 4Z9

69-1631—1 J.S. Rev. 10-03 Printed in U.S.A. www.honeywell.com/yourhome