Analog Electronics I (ECE 201)
Chapter 7: Power Amplifiers
Definitions
In small-signal amplifiers the main factors are:
• Amplification
• Linearity
• Gain
Since large-signal, or power, amplifiers handle relatively large
voltage signals and current levels, the main factors are:
• Efficiency
• Maximum power capability
• Impedance matching to the output device
2
Amplifier Types
Class A
The amplifier conducts through the full 360 of the input. The Q-point is
set near the middle of the load line.
Class B
The amplifier conducts through 180 of the input. The Q-point is set at
the cutoff point.
Class AB
This is a compromise between the class A and B amplifiers. The
amplifier conducts somewhere between 180 and 360 . The Q-point is
located between the mid-point and cutoff.
more…
3
Amplifier Types
Class C
The amplifier conducts less than 180 of the input. The Q-point is located
below the cutoff level.
Class D
This is an amplifier that is biased especially for digital signals.
4
Class A Amplifier
The output of a class A amplifier
conducts for the full 360 of the
cycle.
The Q-point is set at the middle of
the load line so that the AC signal
can swing a full cycle.
Remember that the DC load line
indicates the maximum and minimum
limits set by the DC power supply.
5
Class B Amplifier
A class B amplifier output
only conducts for 180 or
one-half of the AC input
signal.
The Q-point is at 0V on the
load line, so that the AC
signal can only swing for
one-half cycle.
6
Class AB Amplifier
This amplifier is a compromise between the
class A and class B amplifier—the Q-point
is above that of the Class B but below the
class A.
The output conducts between 180 and
360 of the AC input signal.
7
Class C
The output of the class C
conducts for less than 180 of the
AC cycle. The Q-point is below
cutoff.
8
Amplifier Efficiency
Efficiency refers to the ratio of output to input power. The lower the amount
of conduction of the amplifier the higher the efficiency.
9
Series-Fed Class A Amplifier
This is similar to the
small-signal amplifier
except that it will handle
higher voltages. The
transistor used is a high-
power transistor.
10
Series-Fed Class A Amplifier
A small input signal
causes the output voltage
to swing to a maximum of
Vcc and a minimum of 0V.
The current can also
swing from 0mA to ICSAT
(VCC/RC)
11
Series-Fed Class A Amplifier
Input Power
The power into the amplifier is from the DC supply. With no input
signal, the DC current drawn is the collector bias current, ICQ.
Pi(dc) VCCI CQ
Output Power
V 2 C(rms) V 2 CE(p - p)
Po(ac) or Po(ac)
RC 8R C
Efficiency
Po(ac)
%η 100
Pi(ac)
12
Transformer-Coupled Class A Amplifier
This circuit uses a
transformer to couple to
the load. This improves
the efficiency of the Class
A to 50%.
13
Transformer Action
A transformer improves the efficiency because it is able to transform
the voltage, current, and impedance
Voltage Ratio
V2 N 2
V1 N1
Current Ratio
I 2 N1
I1 N 2
Impedance Ratio
2
R L R 1 N 1
a 2
RL R2 N2
14
Transformer-Coupled Class A Amplifier
DC Load Line
As in all class A amplifiers
the Q-point is established
close to the midpoint of the
DC load line.
AC Load Line
The saturation point (ICmax)
is at Vcc/RL and the cutoff
point is at V2 (the secondary
voltage of the transformer).
This increases the maximum
output swing because the
minimum and maximum
values of IC and VCE are
spread further apart.
15
Transformer-Coupled Class A Amplifier
Signal Swing and Output AC Power
The voltage swing:
VCE(p p) VCE max VCE min
The current swing:
I C max I C min
The AC power:
(VCEmax VCEmin )(ICmax I Cmin )
Po(ac)
8
16
Transformer-Coupled Class A Amplifier
Efficiency
Power input from the DC source:
Pi(dc) VCCI CQ
Power dissipated as heat across the transistor:
PQ Pi(dc) Po(ac) Note: The larger the input and output signal, the
lower the heat dissipation.
Maximum efficiency:
2
V VCEmin Note: The larger VCEmax and smaller VCEmin, the
%η 50 CEmax closer the efficiency approaches the theoretical
VCEmax VCEmin maximum of 50%.
17
Class B Amplifier
In class B, the transistor is
biased just off. The AC signal
turns the transistor on.
The transistor only conducts
when it is turned on by one-
half of the AC cycle.
In order to get a full AC cycle
out of a class B amplifier, you
need two transistors:
• An npn transistor that provides the
negative half of the AC cycle
• A pnp transistor that provides the
positive half.
18
Class B Amplifier: Efficiency
The maximum efficiency of a class B is 78.5%..
Po(ac )
% 100
Pi(dc )
2
VCC
maximum Po(dc)
2R L
For maximum power, VL=VCC
2VCC 2V 2 CC
maximum Pi(dc) VCC (maximum I dc ) VCC
πR L πR L
19
Transformer-Coupled Push-Pull
Class B Amplifier
The center-tapped
transformer on the input
produces opposite
polarity signals to the
two transistor inputs.
The center-tapped
transformer on the
output combines the two
halves of the AC
waveform together.
20
Class B Amplifier Push-Pull Operation
• During the positive
half-cycle of the AC
input, transistor Q1
(npn) is conducting
and Q2 (pnp) is off.
• During the negative
half-cycle of the AC
input, transistor Q2
(pnp) is conducting
and Q1 (npn) is off.
Each transistor produces one-half of an AC cycle. The transformer combines the
two outputs to form a full AC cycle.
21
Crossover Distortion
If the transistors Q1 and Q2 do
not turn on and off at exactly
the same time, then there is a
gap in the output voltage.
22
Quasi-Complementary Push-Pull Amplifier
A Darlington pair and a feedback
pair combination perform the
push-pull operation. This
increases the output power
capability.
23
Amplifier Distortion
If the output of an amplifier is not a complete AC sine wave,
then it is distorting the output. The amplifier is non-linear.
This distortion can be analyzed using Fourier analysis. In
Fourier analysis, any distorted periodic waveform can be
broken down into frequency components. These
components are harmonics of the fundamental frequency.
24
Harmonics
Harmonics are integer multiples of a fundamental frequency.
If the fundamental frequency is 5kHz:
1st harmonic 1 x 5kHz
2nd harmonic 2 x 5kHz
3rd harmonic 3 x 5kHz
4th harmonic 4 x 5kHz
etc.
Note that the 1st and 3rd harmonics are called odd harmonics and the
2nd and 4th are called even harmonics.
25
Harmonic Distortion
According to Fourier
analysis, if a signal is not
purely sinusoidal, then it
contains harmonics.
26
Harmonic Distortion Calculations
Harmonic distortion (D) can be calculated:
An
% nth harmonic distortion %D n 100
A1
where
An is the amplitude of the fundamental frequency
An is the amplitude of the highest harmonic
The total harmonic distortion (THD) is determined by:
% THD D 22 D 23 D 23 100
27
Power Transistor Derating Curve
Power transistors dissipate
a lot of power in heat. This
can be destructive to the
amplifier as well as to
surrounding components.
28
Class C Amplifiers
A class C amplifier conducts for less
than 180. In order to produce a full
sine wave output, the class C uses a
tuned circuit (LC tank) to provide
the full AC sine wave.
Class C amplifiers are used
extensively in radio communications
circuits.
29
Class D Amplifier
A class D amplifier amplifies
pulses, and requires a pulsed
input.
There are many circuits that
can convert a sinusoidal
waveform to a pulse, as well
as circuits that convert a
pulse to a sine wave. This
circuit has applications in
digital circuitry.
30
Thanks?
Questions?
Suggestions?
Comments?
