Pipe Supports, Guides, Shields & Saddles

Shields & Saddles

Supports, Guides,

Pipe supports offered in this section are designed to support pipe from a base structure where vertical
adjustment may be required. Pipe guides and slides are designed to allow longitudinal movement due to thermal
expansion and contraction of pipe. Protection shields and saddles are designed to prevent damage to pipe insulation.

Materials
Carbon Steel is used in the manufacturing of pipe supports, guides, shields and saddles. Stainless Steel and other
materials are available.

Finishes
The standard finishes for mechanical supports are plain steel (oil coated) sometimes referred to as black and
Electro-Plated Zinc (ASTM B 633 SC3). Hot-Dip Galvanized After Fabrication (ASTM A 123), Red Primer,
DURA-GREEN™ and other special coatings are available upon request.
Note: Due to the design of some products, (threads, connecting hardware, swivels, etc.) items may or may not be
uniformly coated with special finishes. In some cases, the hanger itself may be coated, however, the hardware may be
supplied Electro-Plated, Copper plated, or in Stainless Steel.

Approvals (as noted)

Items in this section comply with Federal Specification WW-H-171E & A-A-1192A or Manufacturers Standardization
Society ANSI/MSS SP-69 & SP-58.
All pipe supports in this section are sized to fit schedule 40/80 pipe unless otherwise noted. Some steel items may be
specially fabricated to fit other pipe diameters i.e. ductile iron, cast iron, etc. See pipe data charts on pages 294 thru 300
for proper size selection.

122
 Pipe Supports, Guides, Shields & Saddles

Fig. B3380 thru B3387 Size Range: Up to 24” (600mm)

360° Calcium Silicate Shield Material: Asbestos-free, Hydrous Calcium Silicate
Pre-Insulated Support Insulation with Pre-Galvanized steel jacket

Shields & Saddles

Supports, Guides,
Function: Designed to provide a crush resistant
insulation insert at pipe support points. Can be used
with hangers or straps.
Chilled Water
Miscellaneous Information: Flame retardant, water
Type
and rot resistant, temperature range from ambient to
1200°F (649°C). Easily installed in a pipe hanger or
mounted to strut.
Order By: Figure number.
(See part number legend below.)
For additional information, contact factory.

Applications
Standard
Temperature Type

Pipe Hanger Strut Mounted

B338 0 CT - 3

Prefix Insulation Thickness Pipe Type Pipe Size

B338 0 = 1/2” (13mm) CT = Copper Tubing Sizes Nominal Pipe
Commercial Duty, 1 = 3/4” (19mm) Blank = Std. Sch. 40 Steel or
All Purpose Support * 2 = 1” (25mm) Copper Tubing Size
3 = 11/2” (38mm)
4 = 2” (51mm) Note:
* Other models available 6 = 3” (76mm) Up to 24” (600)
Consult Factory 7 = 4” (101mm) pipe size

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

123
 Pipe Supports, Guides, Shields & Saddles
Fig. B3088 - Base Stand (TOLCO Fig. 316) **Height from top of
pipe to bottom of
Stand Pipe Size
plate.
Size Range: 3/4" (20mm) thru 6" (150mm) pipe
Material: Steel **Specify H
Height 4 Holes
Function: Designed as an unthreaded base stand for
Shields & Saddles
Supports, Guides,

pipe supports B3090, B3094, B3095, B3096, B3097 and A

B3098.
Finish: Plain or Electro-Galvanized. Contact Cooper A
B-Line for alternative finishes and materials.
Plate Size
Order By: Figure number, height and finish.

Note: Match B3088 part number with dimension 'D' from B3090, B3094, B3095, B3096, B3097 or B3098 charts.

Plate Size Stand Pipe Size A Dia. H Approx. Wt./100*

Part No. in. (mm) in. (mm) in. (mm) in. (mm) Lbs. (kg)

B3088-3/4 1/4" x 6" x 6" (6.3 x 152.4 x 152.4) 3/4" (20) 7/8" (22.2) 3/4" (14.3) 420 (190.5)
B3088-1 1/4" x 6" x 6" (6.3 x 152.4 x 152.4) 1" (25) 7/8" (22.2) 3/4" (14.3) 480 (216.0)
B3088-11/4 1/4" x 6" x 6" (6.3 x 152.4 x 152.4) 11/4” (32) 7/8" (22.2) 3/4" (14.3) 590 (267.6)
B3088-11/2 1/4" x 6" x 6" (6.3 x 152.4 x 152.4) 11/2" (40) 7/8" (22.2) 3/4" (14.3) 655 (297.1)
B3088-2 1/4" x 6" x 6" (6.3 x 152.4 x 152.4) 2" (50) 7/8" (22.2) 3/4" (14.3) 1211 (549.3)
B3088-21/2 3/8" x 8" x 8" (9.5 x 203.2 x 203.2) 21/2" (65) 11/4" (31.7) 13/16" (14.3) 2376 (1077.7)
B3088-3 3/8" x 12" x 12" (9.5 x 203.2 x 203.2) 3" (80) 11/2" (38.1) 13/16" (20.6) 3137 (1422.9)
B3088-4 1/2" x 12" x 12" (12.7 x 304.8 x 304.8) 4" (100) 11/2" (38.1) 15/16" (23.8) 4338 (1967.7)
B3088-6 1/2" x 18" x 18" (12.7 x 304.8 x 304.8) 6" (150) 11/2" (38.1) 11/8" (28.6) 7378 (3346.6)

*Based on a height of 18" (457.2mm).

Fig. B3088T - Threaded Base Stand (TOLCO Fig. 316T) **Height from top of
TL
pipe to bottom of
plate. Thread Length
Size Range: 1" (25mm) thru 6" (150mm) pipe
Material: Steel Stand Pipe Size
**Specify
Function: Designed as a threaded base stand where Height H
vertical adjustment is required for pipe supports B3089, 4 Holes
B3092, and B3093.
A
Finish: Plain or Electro-Galvanized. Contact Cooper
B-Line for alternative finishes and materials.
A
Order By: Figure number, height and finish.
Plate Size

Note: Match B3088T part number with dimension 'D' from B3089, B3092, and B3093 charts.

Plate Size Stand Pipe Size A Dia. H TL Approx. Wt./100*

Part No. in. (mm) in. (mm) in. (mm) in. (mm) in. (mm) Lbs. (kg)
B3088T-1 1/4"x 6"x 6" (6.3 x 152.4 x 152.4) 1" (25) 7/8" (22.2) 3/4" (19.0) 11/2" (38.1) 495 (224.5)
B3088T-11/4 1/4"x 6"x 6" (6.3 x 152.4 x 152.4) 11/4" (32) 7/8" (22.2) 3/4" (19.0) 11/2" (38.1) 583 (264.4)
B3088T-11/2 1/4"x 6"x 6" (6.3 x 152.4 x 152.4) 11/2" (40) 7/8" (22.2) 3/4" (19.0) 11/2" (38.1) 649 (294.4)
B3088T-2 1/4"x 6"x 6" (6.3 x 152.4 x 152.4) 2" (50) 7/8" (22.2) 3/4" (19.0) 11/2" (38.1) 785 (356.1)
B3088T-21/2 3/8"x 8"x 8" (9.5 x 203.2 x 203.2) 21/2" (65) 11/4" (31.7) 13/16" (20.6) 11/2" (38.1) 1524 (691.3)
B3088T-3 3/8"x 12"x 12" (9.5 x 304.8 x 304.8) 3" (80) 11/2" (38.1) 13/16" (20.6) 11/2" (38.1) 2624 (1190.2)
B3088T-4 1/2"x 12"x 12" (12.7 x 304.8 x 304.8) 4" (100) 11/2" (38.1) 15/16" (23.8) 2" (50.8) 3594 (1630.2)
B3088T-6 1/2"x 18"x 18" (12.7 x 457.2 x 457.2) 6" (150) 11/2" (38.1) 11/8" (28.6) 2" (50.8) 7346 (3332.1)

*Based on a height of 18" (457.2mm).

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

124
 Pipe Supports, Guides, Shields & Saddles
Fig. B3088S - Seismic Base Stand **Height from top of
pipe to bottom of plate.
Stand Pipe Size
Size Range: 3/4" (20mm) thru 4" (100mm) pipe
Material: Steel **Specify H
Height 4 Holes
Function: Designed as an unthreaded base stand for

Shields & Saddles

Supports, Guides,
pipe supports, B3090, B3094, B3095, B3096, B3097 and A
B3098, to meet requirements of 12X anchor diameter
hole spacing for seismic applications. The standard
A
B3088-3 & B3088-6 already meet this requirement.
Plate Size
Finish: Plain or Electro-Galvanized. Contact Cooper
B-Line for alternative finishes and materials.
Order By: Figure number, height and finish.

Note: Match B3088 part number with dimension 'D' from B3090, B3094, B3095, B3096, B3097 or B3098 charts.

Plate Size Stand Pipe Size A Dia. H Approx. Wt./100*

Part No. in. (mm) in. (mm) in. (mm) in. (mm) Lbs. (kg)
B3088S-3/4 1/4" x 8" x 8" (6.3 x 203.2 x 203.2) 3/4" (20) 1" (25.4) 9/16" (14.3) 618 (280.3)
B3088S-1 1/4" x 8" x 8" (6.3 x 203.2 x 203.2) 1" (25) 1" (25.4) 9/16" (14.3) 708 (321.1)
B3088S-11/4 1/4" x 8" x 8" (6.3 x 203.2 x 203.2) 11/4” (20) 1" (25.4) 9/16" (14.3) 798 (362.0)
B3088S-11/2 1/4" x 8" x 8" (6.3 x 203.2 x 203.2) 11/2" (32) 1" (25.4) 9/16" (14.3) 858 (389.2)
B3088S-2 1/4" x 8" x 8" (6.3 x 203.2 x 203.2) 2" (50) 1" (25.4) 9/16" (14.3) 993 (450.4)
B3088S-21/2 3/8" x 81/2" x 81/2" (9.5 x 215.9 x 215.9) 21/2" (65) 11/4" (31.7) 9/16" (14.3) 1638 (743.0)
B3088S-4 1/2" x 131/2" x 131/2" (12.7 x 342.9 x 342.9) 4" (100) 11/2" (38.1) 15/16" (23.8) 4202 (1906.0)

*Based on a height of 18" (457.2mm).

**Height from top

Fig. B3088ST - Threaded Seismic Base Stand of pipe to bottom TL
of plate. Thread Length
Size Range: 1" (25mm) thru 4" (100mm) pipe
Stand Pipe Size
Material: Steel **Specify
Function: Designed as a threaded base stand where vertical Height H
4 Holes
adjustment is required for pipe supports B3089, B3092, and
B3093, to meet requirements of 12X anchor diameter hole A
spacing for seismic applications. The standard B3088T-3 &
B3088T-6 already meet this requirement. A
Finish: Plain or Electro-Galvanized. Contact Cooper B-Line
for alternative finishes and materials. Plate Size
Order By: Figure number, height and finish.

Note: Match B3088T part number with dimension 'D' from B3089, B3092, and B3093 charts.

Plate Size Stand Pipe Size A Dia. H TL Approx. Wt./100*

Part No. in. (mm) in. (mm) in. (mm) in. (mm) in. (mm) Lbs. (kg)
B3088ST-1 1/4" x 8" x 8" (6.3 x 203.2 x 203.2) 1" (25) 1" (25.4) 9/16" (14.3) 11/2" (38.1) 708 (321.1)
B3088ST-11/4 1/4" x 8" x 8" (6.3 x 203.2 x 203.2) 11/4" (32) 1" (25.4) 9/16" (14.3) 11/2" (38.1) 798 (362.0)
B3088ST-11/2 1/4" x 8" x 8" (6.3 x 203.2 x 203.2) 11/2" (40) 1" (25.4) 9/16" (14.3) 11/2" (38.1) 858 (389.2)
B3088ST-2 1/4" x 8" x 8" (6.3 x 203.2 x 203.2) 2" (50) 1" (25.4) 9/16" (14.3) 11/2" (38.1) 993 (450.4)
B3088ST-21/2 3/8" x 81/2" x 81/2" (9.5 x 215.9 x 215.9) 21/2" (65) 11/4" (31.7) 9/16" (14.3) 11/2" (38.1) 1638 (743.0)
B3088ST-4 1/2" x 131/2" x 131/2" (12.7 x 342.9 x 342.9) 4" (100) 11/2" (38.1) 15/16" (23.8) 2" (50.8) 4202 (1906.0)

*Based on a height of 18" (457.2mm).

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

125
 Pipe Supports, Guides, Shields & Saddles
Fig. B3096 - Adjustable Pipe Saddle Support (TOLCO Fig. 312)
Size Range: Size 2" (505mm) thru 12" (300mm) pipe
Steel Size
Material: Steel
Function: Designed to support horizontal pipe from
Shields & Saddles
Supports, Guides,

floor stanchion where vertical adjustment is required.

Approvals: Conforms to Federal Specification
A
WW-H-171E & A-A-1192A, Type 39 and Manufacturers Thread Size
Standardization Society ANSI/MSS SP-69 & SP-58, 8"
Type 38. Hex Nut Included
(203.2)

Maximum Temperature: 650°F (343°C)

Finish: Plain. Contact Cooper B-Line for alternative
finishes and materials.
Order By: Figure number, pipe size and finish
Shank will fit into Sch. 40
Pipe Size ‘D’ (not included)

Pipe Size Max. Pipe O.D. Thread D Steel Size Approx. Wt./100
Part No. in. (mm) in. (mm) Size A in. (mm) in. (mm) Lbs. (kg)

B3096-2 2" (50) 23/8" (60.3) 7/8"-9 1" (25) 3/8" x 2" (9.5 x 50.8) 212 (96.1)
B3096-3 3" (80) 31/2" (88.9) 7/8"-9 1" (25) 3/8" x 21/2" (9.5 x 63.5) 259 (117.5)
B3096-4 4" (100) 41/2" (114.3) 1"-8 1" (25) 3/8" x 3" (9.5 x 76.2) 370 (167.8)
B3096-5 5" (125) 59/16" (141.3) 1"-8 1" (25) 3/8" x 3" (9.5 x 76.2) 404 (183.2)
B3096-6 6" (150) 65/8" (168.3) 11/4"-7 11/4" (32) 1/2" x 31/2" (12.7 x 88.9) 714 (323.9)
B3096-8 8" (200) 85/8" (219.1) 11/4"-7 11/4" (32) 1/2" x 31/2" (12.7 x 88.9) 819 (371.5)
B3096-10 10" (250) 103/4" (273.0) 11/2"-6 11/2" (40) 1/2" x 4" (12.7 x 101.6) 1194 (541.6)
B3096-12 12" (300) 123/4" (323.8) 11/2"-6 11/2" (40) 1/2" x 4" (12.7 x 101.6) 1315 (596.5)

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

126
 Pipe Supports, Guides, Shields & Saddles
Fig. B3089 - Pipe Adjuster (TOLCO Fig. 319)
Size Range: For use with 11⁄2" (40mm) thru 36" (900mm) pipe
Material: Steel
Function: Straight threaded shank that permits adjustment

Shields & Saddles

Supports, Guides,
after installation B
Pipe Size
Approvals: Conforms to Federal Specification WW-H-171E &
A-A-1192A, Type 38 and Manufacturers Standardization Society
ANSI/MSS SP-69 & SP-58, Type 37, when used with B3090,
B3094 and B3095 Pipe Supports.
Maximum Temperature: 650°F (343°C)
Finish: Plain. Contact Cooper B-Line for alternative finishes and D
materials. Nominal pipe size of base
stand - not included
Order By: Figure number and finish

Note:
If combining a Figure B3089 (Pipe adjuster) with a Figure B3090
(Pipe Support - pages 128 & 129) the catalog number will
become a Figure B3092 (see pages 132 & 133).
If combining a Figure B3089 (Pipe adjuster) with a Figure B3095
(Pipe Support Saddle - pages 130 & 131) the catalog number
will become a Figure B3093 (see pages 133 & 134).

To Support Pipe Size B D Approx. Wt./100

Part No. in. (mm) in. (mm) in. (mm) Lbs. (kg)
B3089-3/4 11/2" - 2" (40 - 50) 3/4" (20) 11/2" (40) 140 (63.5)

B3089-11/2 21/2" - 31/2" (65 - 90) 11/2" (40) 21/2" (65) 400 (181.4)

B3089-21/2 4" - 12" (100 - 300) 21/2" (65) 3" (80) 700 (317.5)
B3089-3 14" - 16" (350 - 400) 3" (80) 4" (100) 1000 (453.6)
B3089-4 18" - 36" (450 - 900) 4" (100) 6" (150) 2200 (997.9)

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

127
 Pipe Supports, Guides, Shields & Saddles
Fig. B3090 - Pipe Support with U-Bolt (TOLCO Fig. 318)
Size Range: — 3/4" (20mm) thru 36" (900mm) pipe A
U-Bolt Dia.
Material: — Steel
C
Shields & Saddles
Supports, Guides,

Function: — Designed to support horizontal pipe from floor stanchion.

U-bolts and hex nuts are provided to hold pipe securely to saddle. To Steel Size
complete floor stanchion, use with B3088 pipe stand.
4"
Approvals: — Conforms to Federal Specification WW-H-171E & A-A-1192A, (101.6) Gussets on sizes B3090-8
Type 38 and Manufacturers Standardization Society ANSI/MSS SP-69 & and larger.
SP-58, Type 37 B (Shank Dia.)

Maximum Temperature: — 750°F (399°)

C
Finish: — Plain. Contact Cooper B-Line for alternative finishes and Center of pipe to
bottom lip of support.
materials.
Order By: — Figure number and finish Shank will fit into nominal
Schedule 40 pipe size 'D' of
Base Stand Figure B3088
(not included).
Note: — For vertical adjustment see Figure B3092 (pages 132 & 133)

Pipe Size Max. O.D. of Pipe Steel Size A

Part No. in. (mm) in. (mm) in. (mm) in. (mm)
B3090-3/4 3/4" (20) 13/8" (34.9) 1/4" x 11/2" (6.3 x 38.1) 1/4" (6.4)
B3090-1 1" (25) 13/8" (34.9) 1/4" x 11/2" (6.3 x 38.1) 1/4" (6.4)
B3090-11/4 11/4" (32) 111/16" (42.9) 1/4" x 2" (6.3 x 50.8) 3/8" (9.5)
B3090-11/2 11/2" (40) 2" (50.8) 1/4" x 2" (6.3 x 50.8) 3/8" (9.5)
B3090-2 2" (50) 27/16" (61.9) 1/4" x 2" (6.3 x 50.8) 3/8" (9.5)
B3090-21/2 21/2" (65) 27/8" (73.0) 1/4" x 3" (6.3 x 76.2) 1/2" (12.7)
B3090-3 3" (80) 31/2" (88.9) 1/4" x 3" (6.3 x 76.2) 1/2" (12.7)
B3090-31/2 31/2" (90) 4" (101.6) 1/4" x 3" (6.3 x 76.2) 1/2" (12.7)
B3090-4 4" (100) 47/8" (123.8) 3/8" x 31/2" (9.5 x 88.9) 1/2" (12.7)
B3090-5 5" (125) 55/8" (142.9) 3/8" x 31/2" (9.5 x 88.9) 1/2" (12.7)
B3090-6 6" (150) 629/32" (175.4) 1/2" x 31/2" (12.7 x 88.9) 5/8" (15.9)
B3090-8 8" (200) 91/8" (231.8) 1/2" x 31/2" (12.7 x 88.9) 5/8" (15.9)
B3090-10 10" (250) 113/32" (281.8) 1/2" x 31/2" (12.7 x 88.9) 3/4" (19.0)
B3090-12 12" (300) 133/16" (335.0) 1/2" x 31/2" (12.7 x 88.9) 7/8" (22.2)
B3090-14 14" (350) 14" (355.6) 5/8" x 4" (19.0 x 101.6) 7/8" (22.2)
B3090-16 16" (400) 16" (406.4) 5/8" x 4" (19.0 x 101.6) 7/8" (22.2)
B3090-18 18" (450) 18" (457.2) 3/4" x 5" (19.0 x 127.0) 1" (25.4)
B3090-20 20" (500) 20" (508.0) 3/4" x 5" (19.0 x 127.0) 1" (25.4)
B3090-24 24" (600) 24" (609.6) 1" x 5" (25.4 x 127.0) 1" (25.4)
B3090-30 30" (750) 30" (762.0) 1" x 5" (25.4 x 127.0) 1" (25.4)
B3090-36 36" (900) 36" (914.4) 1" x 5" (25.4 x 127.0) 1" (25.4)

Note:
4" (100) thru 12" (300) fits both steel and ductile iron pipe.
For other ductile iron pipe sizes specify B3090DI - size.
3” (80) Ductile Iron uses B3090-31/2

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

128
 Pipe Supports, Guides, Shields & Saddles
Fig. B3090 - Pipe Support with U-Bolt (TOLCO Fig. 318) cont.

Shields & Saddles

Supports, Guides,
A
U-Bolt Dia.
C

Steel Size

4"
(101.6) Gussets on sizes B3090-8
and larger.
B (Shank Dia.)

C
Center of pipe to Shank will fit into nominal
bottom lip of support. Schedule 40 pipe size 'D' of
Base Stand Figure B3088
(not included).

Note: — For vertical adjustment see Figure B3092 (pages 132 & 133)

B C D Approx. Wt./100
Part No. in. (mm) in. (mm) in. (mm) Lbs. (kg)
B3090-3/4 3/4" (19.0) 2" (50.8) 3/4" (19) 107 (48.5)
B3090-1 3/4" (19.0) 25/32" (54.8) 3/4" (19) 117 (53.1)
B3090-11/4 3/4" (19.0) 221/64" (59.1) 3/4" (19) 149 (67.6)
B3090-11/2 3/4" (19.0) 21/2" (63.5) 3/4" (19) 166 (75.3)
B3090-2 3/4" (19.0) 211/16" (68.3) 3/4" (19) 186 (84.4)
B3090-21/2 15/16" (33.3) 31/8" (79.4) 11/2" (40) 251 (113.8)
B3090-3 15/16" (33.3) 37/16" (87.3) 11/2" (40) 316 (143.3)
B3090-31/2 15/16" (33.3) 311/16" (93.7) 11/2" (40) 317 (143.8)
B3090-4 23/8" (60.3) 41/16" (103.2) 21/2" (65) 586 (265.8)
B3090-5 23/8" (60.3) 417/32" (115.1) 21/2" (65) 621 (281.7)
B3090-6 23/8" (60.3) 55/16" (134.9) 21/2" (65) 895 (406.0)
B3090-8 23/8" (60.3) 63/4" (171.4) 21/2" (65) 1115 (505.7)
B3090-10 23/8" (60.3) 713/16" (198.4) 21/2" (65) 1423 (645.5)
B3090-12 23/8" (60.3) 813/16" (223.8) 21/2" (65) 1846 (837.3)
B3090-14 27/8" (73.0) 109/16" (268.3) 3" (80) 2593 (1176.2)
B3090-16 27/8" (73.0) 119/16" (293.7) 3" (80) 2825 (1281.4)
B3090-18 4" (101.6) 139/16" (344.5) 4" (100) 4843 (2196.8)
B3090-20 4" (101.6) 149/16" (369.9) 4" (100) 5225 (2370.0)
B3090-24 4" (101.6) 169/16" (420.7) 4" (100) 6970 (3161.6)
B3090-30 4" (101.6) 2011/16" (525.5) 4" (100) 8587 (3895.0)
B3090-36 4" (101.6) 2311/16" (601.7) 4" (100) 9977 (4525.5)

Note:
4" (100) thru 12" (300) fits both steel and ductile iron pipe.
For other ductile iron pipe sizes specify B3090DI - size.
3” (80) Ductile Iron uses B3090-31/2

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

129
 Pipe Supports, Guides, Shields & Saddles
Fig. B3095 - Pipe Saddle Support (TOLCO Fig. 317)
E
Size Range: 11⁄2" (40mm) thru 36" (900mm) pipe C
A
Material: Steel Steel Size Shank Length
B
Shields & Saddles
Supports, Guides,

Function: Designed to support horizontal pipe from floor stanchion. Gussets on sizes Shank Dia.
To complete floor stanchion, use with B3088 pipe stand. B3095-8 and larger.
C
Approvals: Conforms to Federal Specification WW-H-171E & A-A-1192A, A Center of pipe to
B
Type 37 and Manufacturers Standardization Society ANSI/MSS SP-69 & bottom lip of support.
SP-58, Type 36
Shank will fit into nominal
Maximum Temperature: 750°F (399°C) Schedule 40 pipe size 'D' of
Finish: Plain. Available in Electro-Galvanized and HDG finish or Base Stand Figure B3088
(not included).
Stainless Steel materials.
Order By: Figure number and finish

Note: — For vertical adjustment see Figure B3093 (pages 134 & 135)

Pipe Size Max. O.D. of Pipe A B C

Part No. in. (mm) in. (mm) in. (mm) in. (mm) in. (mm)
B3095-1 1" (25) 15/16" (33.3) 3" (76.2) 3/4" (19.0) 129/32" (48.4)
B3095-11/4 11/4" (32) 111/16" (42.9) 3" (76.2) 3/4" (19.0) 25/64" (52.8)
B3095-11/2 11/2" (40) 115/16" (49.2) 3" (76.2) 3/4" (19.0) 213/64" (55.9)
B3095-2 2" (50) 23/8" (60.3) 3" (76.2) 3/4" (19.0) 27/16" (61.9)
B3095-21/2 21/2" (65) 27/8" (73.0) 4" (101.6) 15/16" (33.3) 29/16" (65.1)
B3095-3 3" (80) 31/2" (88.9) 4" (101.6) 15/16" (33.3) 3" (76.2)
B3095-31/2 31/2" (90) 4" (101.6) 4" (101.6) 15/16" (33.3) 314" (82.5)
B3095-4 4" (100) 47/8" (123.8) 4" (101.6) 23/8" (60.3) 31/2" (88.9)
B3095-5 5" (125) 55/8" (142.9) 4" (101.6) 23/8" (60.3) 41/32" (102.4)
B3095-6 6" (150) 7" (177.8) 4" (101.6) 23/8" (60.3) 411/16" (119.1)
B3095-8 8" (200) 91/8" (231.8) 4" (101.6) 23/8" (60.3) 61/16" (154.0)
B3095-10 10" (250) 111/8" (282.6) 4" (101.6) 23/8" (60.3) 73/4" (196.8)
B3095-12 12" (300) 131/2" (342.9) 4" (101.6) 23/8" (60.3) 83/4" (222.2)
B3095-14 14" (350) 14" (355.6) 4" (101.6) 27/8" (72.9) 103/4" (273.0)
B3095-16 16" (400) 16" (406.4) 4" (101.6) 27/8" (72.9) 113/4" (298.4)
B3095-18 18" (450) 18" (457.2) 4" (101.6) 4" (101.6) 141/2" (368.3)
B3095-20 20" (500) 20" (508.0) 4" (101.6) 4" (101.6) 141/2" (368.3)
B3095-24 24" (600) 24" (609.6) 4" (101.6) 4" (101.6) 173/4" (450.8)
B3095-30 30" (750) 30" (762.0) 4" (101.6) 4" (101.6) 211/4" (539.7)
B3095-36 36" (900) 36" (914.4) 4" (101.6) 4" (101.6) 241/4" (615.9)

Note:
4" (100) thru 12" (300) fits both steel and ductile iron pipe.
For other ductile iron pipe sizes specify B3095DI - size.
3” (80) Ductile Iron uses B3095-31/2

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

130
 Pipe Supports, Guides, Shields & Saddles
Fig. B3095 - Pipe Saddle Support (TOLCO Fig. 317) cont.

Shields & Saddles

Supports, Guides,
E
C A
Shank Length
Steel Size
B
Shank Dia.
Gussets on sizes
B3095-8 and larger. C
A Center of pipe to
B bottom lip of support.

Shank will fit into nominal

Schedule 40 pipe size 'D' of
Base Stand Figure B3088
(not included).

Note: — For vertical adjustment see Figure B3093 (pages 134 & 135)

D E Approx. Wt./100
Part No. in. (mm) in. (mm) Lbs. (kg)
B3095-1 3/4" (20) 11/8" (28.6) 49 (22.2)
B3095-11/4 3/4" (20) 17/16" (36.5) 81 (36.7)
B3095-11/2 3/4" (20) 121/32" (42.0) 88 (39.9)
B3095-2 3/4" (20) 21/16" (52.4) 94 (42.6)
B3095-21/2 11/2" (40) 21/2" (63.5) 167 (75.7)
B3095-3 11/2" (40) 31/32" (77.0) 176 (79.8)
B3095-31/2 11/2" (40) 37/16" (87.3) 188 (85.3)
B3095-4 21/2" (65) 41/4" (107.9) 364 (165.1)
B3095-5 21/2" (65) 413/16" (122.2) 381 (172.8)
B3095-6 21/2" (65) 61/16" (154.0) 534 (242.2)
B3095-8 21/2" (65) 715/16" (201.5) 796 (361.0)
B3095-10 21/2" (65) 95/8" (244.5) 914 (414.6)
B3095-12 21/2" (65) 1111/16" (296.9) 1068 (484.4)
B3095-14 3" (80) 121/8" (308.0) 1654 (750.2)
B3095-16 3" (80) 137/8" (352.4) 1817 (824.2)
B3095-18 4" (100) 1519/32" (396.1) 2798 (1269.2)
B3095-20 4" (100) 175/16" (439.7) 3018 (1368.9)
B3095-24 4" (100) 2025/32" (527.8) 3018 (1368.9)
B3095-30 4" (100) 26" (660.4) 7624 (3458.2)
B3095-36 4" (100) 313/16" (792.2) 8877 (4026.6)

Note:
4" (100) thru 12" (300) fits both steel and ductile iron pipe.
For other ductile iron pipe sizes specify B3095DI - size.
3” (80) Ductile Iron uses B3095-31/2

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

131
 Pipe Supports, Guides, Shields & Saddles
Fig. B3092 - Adjustable Pipe Saddle Support with Yoke (TOLCO Fig. 318A)
Size Range: 3/4" (20mm) thru 36" (900mm) pipe
E A
Material: Steel with cast iron reducer U-Bolt Dia. Schedule 40 Pipe Size
Shields & Saddles
Supports, Guides,

C B
Function: Designed to support horizontal pipe from floor
Center of pipe to
stanchion where vertical adjustment is required. U-bolt Steel Size bottom of pipe reducer.
and hex nuts are provided to hold pipe securely to saddle. B
C
To complete floor stanchion, use with B3088T threaded Gussets on sizes
Center of pipe to
pipe stand. bottom lip of support.
B3092-8 and larger.
D
Approvals: Conforms to Federal Specification A Nominal pipe size of base stand -
WW-H-171E & A-A-1192A and Manufacturers Figure B3088T, not included.
Standardization Society ANSI/MSS SP-69 & SP-58, Type 37. D E
U-Bolt Dia.
Finish: Plain. Contact Cooper B-Line for alternative finishes
and materials.
Order By: Figure number and finish
Notes: Order with B3088T for complete stanchion support.
4" (100mm) thru 12" (300mm) fits both steel and ductile iron
pipe. For other ductile iron pipe sizes specify B3092DI - size.
3” (80mm) Ductile Iron uses B3092-31/2

Pipe Size Maximum A Minimum B Maximum

Part No. in. (mm) in. (mm) in. (mm) in. (mm) in. (mm)
B3092-3/4 3/4" (19) 13/8" (34.9) 3/4" (19) 53/4" (146.0) 101/4" (260.3)
B3092-1 1" (25) 13/8" (34.9) 3/4" (19) 529/32" (150.0) 1013/32" (264.3)
B3092-11/4 1
1 /4" (32) 111/16" (42.9) 3/4" (19) 65/64" (154.4) 1037/64" (268.7)
B3092-11/2 11/2" (38) 2" (50.8) 3/4" (19) 61/4" (158.7) 103/4" (273.0)
B3092-2 2" (50) 27/16" (61.9) 3/4" (19) 67/16" (163.5) 1015/16" (277.8)
B3092-21/2 21/2" (65) 27/8" (73.0) 11/2" (40) 67/8" (174.6) 113/8" (288.9)
B3092-3 3" (80) 31/2" (88.9) 11/2" (40) 73/16" (182.6) 1111/16" (296.9)
B3092-31/2 31/2" (90) 4" (101.6) 11/2" (40) 77/16" (188.9) 1115/16" (303.2)
B3092-4 4" (100) 47/8" (123.8) 21/2" (65) 713/16" (198.4) 125/16" (312.7)
B3092-5 5" (125) 55/8" (142.9) 21/2" (65) 89/32" (210.3) 1225/32" (324.6)
B3092-6 6" (150) 629/32" (175.4) 21/2" (65) 91/16" (230.2) 139/16" (344.5)
B3092-8 8" (200) 91/8" (231.8) 21/2" (65) 101/2" (266.7) 15" (381.0)
B3092-10 10" (250) 113/32" (281.8) 21/2" (65) 119/16" (293.7) 161/16" (408.0)
B3092-12 12" (300) 133/16" (334.9) 21/2" (65) 129/16" (319.1) 171/16" (433.4)
B3092-14 14" (350) 14" (355.6) 3" (80) 145/16" (363.5) 1813/16" (477.8)
B3092-16 16" (400) 16" (406.4) 3" (80) 155/16" (388.9) 1913/16" (503.2)
B3092-18 18" (450) 18" (457.2) 4" (100) 175/16" (439.7) 2113/16" (554.0)
B3092-20 20" (500) 20" (508.0) 4" (100) 185/16" (465.1) 2213/16" (579.4)
B3092-24 24" (600) 24" (609.6) 4" (100) 205/16" (515.9) 2413/16" (630.2)
B3092-30 30" (750) 30" (762.0) 4" (100) 247/16" (620.7) 2815/16" (735.0)
B3092-36 36" (900) 36" (914.4) 4" (100) 277/16" (696.9) 3115/16" (811.2)

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

132
 Pipe Supports, Guides, Shields & Saddles
Fig. B3092 - Adjustable Pipe Saddle Support with Yoke (TOLCO Fig. 318A) cont.

Shields & Saddles

Supports, Guides,
E A
U-Bolt Dia. Schedule 40 Pipe Size
C B
Center of pipe to
Steel Size bottom of pipe reducer.
B
C
Center of pipe to
Gussets on sizes bottom lip of support.
B3092-8 and larger.
D
A Nominal pipe size of base stand -
Figure B3088T, not included.
D E
U-Bolt Dia.

C D E Saddle Steel Size Approx. Wt./100

Part No. in. (mm) in. (mm) in. (mm) in. (mm) Lbs. (kg)
B3092-3/4 2" (50.8) 11/2" (38) 1/4" (6.4) 1/4" x 11/2" (6.3 x 38.1) 247 (112.0)
B3092-1 25/32" (54.8) 11/2" (38) 1/4" (6.4) 1/4" x 11/2" (6.3 x 38.1) 257 (116.6)
B3092-11/4 221/64" (59.1) 11/2" (38) 3/8" (9.5) 1/4" x 2" (6.3 x 50.8) 289 (131.1)
B3092-11/2 21/2" (63.5) 11/2" (38) 3/8" (9.5) 1/4" x 2" (6.3 x 50.8) 306 (138.8)
B3092-2 211/16" (68.3) 11/2" (38) 3/8" (9.5) 1/4" x 2" (6.3 x 50.8) 326 (147.9)
B3092-21/2 31/8" (79.4) 21/2" (65) 1/2" (12.7) 1/4" x 3" (6.3 x 76.2) 651 (295.3)
B3092-3 37/16" (87.3) 21/2" (65) 1/2" (12.7) 1/4" x 3" (6.3 x 76.2) 716 (324.8)
B3092-31/2 311/16" (93.7) 21/2" (65) 1/2" (12.7) 1/4" x 3" (6.3 x 76.2) 717 (325.2)
B3092-4 41/4" (107.9) 3" (80) 1/2" (12.7) 3/8" x 31/2" (9.5 x 88.9) 1286 (583.3)
B3092-5 49/16" (115.9) 3" (80) 1/2" (12.7) 3/8" x 31/2" (9.5 x 88.9) 1321 (599.2)
B3092-6 51/2" (139.7) 3" (80) 5/8" (15.9) 1/2" x 31/2" (12.7 x 88.9) 1595 (723.5)
B3092-8 7" (177.8) 3" (80) 5/8" (15.9) 1/2" x 31/2" (12.7 x 88.9) 1815 (823.3)
B3092-10 8" (203.2) 3" (80) 3/4" (19.0) 1/2" x 31/2" (12.7 x 88.9) 2123 (963.0)
B3092-12 93/16" (233.4) 3" (80) 7/8" (22.2) 1/2" x 31/2" (12.7 x 88.9) 2546 (1154.8)
B3092-14 109/16" (268.3) 4" (100) 7/8" (22.2) 5/8" x 4" (15.9 x 101.6) 3593 (1629.8)
B3092-16 119/16" (293.7) 4" (100) 7/8" (22.2) 5/8" x 4" (15.9 x 101.6) 3825 (1735.0)
B3092-18 139/16" (344.5) 6" (150) 1" (25.4) 3/4" x 5" (19.0 x 127.0) 7043 (3194.7)
B3092-20 149/16" (369.9) 6" (150) 1" (25.4) 3/4" x 5" (19.0 x 127.0) 7425 (3368.0)
B3092-24 169/16" (420.7) 6" (150) 1" (25.4) 1" x 5" (25.4 x 127.0) 9170 (4159.5)
B3092-30 2011/16" (525.5) 6" (150) 1" (25.4) 1" x 5" (25.4 x 127.0) 10787 (4893.0)
B3092-36 2311/16" (601.7) 6" (150) 1" (25.4) 1" x 5" (25.4 x 127.0) 12177 (5523.5)

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

133
 Pipe Supports, Guides, Shields & Saddles
Fig. B3093 - Adjustable Pipe Saddle Support (TOLCO Fig. 317A)
Size Range: 1" (25mm) thru 36" (900mm) pipe A
Schedule 40 Pipe Size
Material: Steel with cast iron reducer
B C
Steel Size
Shields & Saddles
Supports, Guides,

Function: Designed to support horizontal pipe from Center of pipe to bottom of pipe
reducer.
floor stanchion where vertical adjustment is required.
C
U-bolt and hex nuts are provided to hold pipe Center of pipe to bottom lip of Gussets on sizes B
securely to saddle. To complete floor stanchion, use support. B3093-8 and larger.
with B3088T threaded pipe stand. A
D
Nominal pipe size of base stand -
Approvals: Conforms to Federal Specification Figure B3088T, not included.
WW-H-171E & A-A-1192A, Type 38 and
D
Manufacturers Standardization Society ANSI/MSS
SP-69 & SP-58, Type 37.
Finish: Plain. Contact Cooper B-Line for alternative
finishes and materials.
Order By: Figure number and finish
Note: Order with B3088T for complete stanchion
support.

Pipe Size Maximum A Minimum B Maximum C

Part No. in. (mm) in. (mm) in. (mm) in. (mm) in. (mm) in. (mm)

B3093-1 1" (25) 15/16" (33.3) 3/4" (20) 521/32" (143.6) 105/32" (257.9) 129/32" (48.4)
B3093-11/4 11/4" (32) 111/16" (42.9) 3/4" (20) 553/64" (148.0) 1021/64" (2262.3) 25/64" (52.8)
B3093-11/2 11/2" (40) 129/32" (48.4) 3/4" (20) 6" (152.4) 101/2" (266.7) 21/4" (58.1)
B3093-2 2" (50) 23/8" (60.3) 3/4" (20) 63/16" (157.2) 1011/16" (271.5) 27/16" (61.9)
B3093-21/2 1
2 /2" (65) 27/8" (73.0) 11/2" (40) 65/16" (160.3) 1013/16" (274.6) 29/16" (65.1)
B3093-3 3" (80) 31/2" (88.9) 11/2" (40) 65/8" (168.3) 111/8" (282.6) 27/8" (73.0)
B3093-31/2 31/2" (90) 4" (101.6) 11/2" (40) 67/8" (174.6) 113/8" (288.9) 31/8" (79.4)
B3093-4 4" (100) 47/8" (123.8) 21/2" (65) 71/4" (184.1) 113/4" (298.4) 31/2" (88.9)
B3093-5 5" (125) 59/16" (141.3) 21/2" (65) 725/32" (197.6) 129/32" (311.9) 41/32" (102.4)
B3093-6 6" (150) 7" (177.8) 21/2" (65) 87/16" (214.3) 1215/16" (328.6) 411/16" (119.1)
B3093-8 8" (200) 91/8" (231.8) 21/2" (65) 101/4" (260.3) 143/4" (374.6) 61/2" (165.1)
B3093-10 10" (250) 111/8" (282.6) 21/2" (65) 115/16" (287.3) 1513/16" (401.6) 79/16" (192.1)
B3093-12 12" (300) 131/2" (342.9) 21/2" (65) 121/8" (308.0) 165/8" (422.3) 83/8" (212.7)
B3093-14 14" (350) 14" (355.6) 3" (80) 141/2" (368.3) 19" (482.6) 103/4" (273.0)
B3093-16 16" (400) 16" (406.4) 3" (80) 151/2" (393.7) 20" (508.0) 113/4" (298.4)
B3093-18 18" (450) 18" (457.2) 4" (100) 171/4" (438.1) 213/4" (552.4) 131/2" (342.9)
B3093-20 20" (500) 20" (508.0) 4" (100) 181/4" (463.5) 223/4" (577.8) 141/2" (368.3)
B3093-24 24" (600) 24" (609.6) 4" (100) 211/2" (546.1) 26" (660.4) 173/4" (450.8)
B3093-30 30" (750) 30" (762.0) 4" (100) 245/8" (625.5) 291/8" (739.8) 207/8" (530.2)
B3093-36 36" (900) 36" (914.4) 4" (100) 275/8" (701.7) 321/8" (816.0) 237/8" (606.4)

Note:
4" (100) thru 12" (300) fits both steel and ductile iron pipe.
For other ductile iron pipe sizes specify B3093DI - size.
3” (80) Ductile Iron uses B3093-31/2

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

134
 Pipe Supports, Guides, Shields & Saddles
Fig. B3093 - Adjustable Pipe Saddle Support (TOLCO Fig. 317A) cont.

Shields & Saddles

Supports, Guides,
A
Schedule 40 Pipe Size
B C
Steel Size
Center of pipe to bottom of pipe
reducer.
C
Center of pipe to bottom lip of Gussets on sizes B
support. B3093-8 and larger.
A
D
Nominal pipe size of base stand -
Figure B3088T, not included.
D

Approx. Wt./100
D Saddle Steel Size Complete Saddle Only
Part No. in. (mm) in. (mm) Lbs. (kg) Lbs. (kg)

B3093-1 11/2" (40) 1/4" x 13/4" (6.3 x 44.4) 189 (85.7) 49 (22.2)
B3093-11/4 11/2" (40) 1/4" x 13/4" (6.3 x 44.4) 221 (100.2) 81 (36.7)
B3093-11/2 11/2" (40) 1/4" x 13/4" (6.3 x 44.4) 228 (103.4) 88 (39.9)
B3093-2 11/2" (40) 1/4" x 13/4" (6.3 x 44.4) 234 (106.1) 94 (42.6)
B3093-21/2 21/2" (65) 1/4" x 3" (6.3 x 76.2) 567 (257.2) 167 (75.8)
B3093-3 21/2" (65) 1/4" x 3" (6.3 x 76.2) 576 (261.3) 176 (79.9)
B3093-31/2 21/2" (65) 1/4" x 3" (6.3 x 76.2) 588 (266.7) 188 (85.3)
B3093-4 3" (80) 1/4" x 4" (6.3 x 101.6) 1064 (482.6) 364 (165.1)
B3093-5 3" (80) 1/4" x 4" (6.3 x 101.6) 1081 (490.3) 381 (172.8)
B3093-6 3" (80) 3/8" x 4" (9.5 x 101.6) 1234 (559.7) 534 (242.2)
B3093-8 3" (80) 3/8" x 4" (9.5 x 101.6) 1496 (678.6) 796 (361.1)
B3093-10 3" (80) 3/8" x 4" (9.5 x 101.6) 1614 (732.1) 914 (414.6)
B3093-12 3" (80) 3/8" x 4" (9.5 x 101.6) 1768 (801.9) 1068 (484.4)
B3093-14 4" (100) 3/8" x 5" (9.5 x 127.0) 2654 (1203.8) 1654 (750.2)
B3093-16 4" (100) 3/8" x 5" (9.5 x 127.0) 2817 (1277.8) 1817 (824.2)
B3093-18 6" (150) 1/2" x 5" (12.7 x 127.0) 4998 (2267.1) 2798 (1269.1)
B3093-20 6" (150) 1/2" x 5" (12.7 x 127.0) 5218 (2366.8) 3018 (1368.9)
B3093-24 6" (150) 1/2" x 6" (12.7 x 152.4) 6346 (2878.5) 4146 (1880.6)
B3093-30 6" (150) 1" x 6" (25.4 x 152.4) 9824 (4456.1) 7624 (3458.2)
B3093-36 6" (150) 1" x 6" (25.4 x 152.4) 11077 (5024.4) 8877 (4026.5)

Note:
4" (100) thru 12" (300) fits both steel and ductile iron pipe.
For other ductile iron pipe sizes specify B3093DI - size.
3” (80) Ductile Iron uses B3093-31/2

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

135
 Pipe Supports, Guides, Shields & Saddles
Fig. B3097 - Pipe Saddle With Strap (TOLCO Fig. 311)
A
Size Range: Size 4" (100mm) thru 36" (900mm) pipe
Material: Steel
Function: Designed to support horizontal pipe from
Shields & Saddles
Supports, Guides,

B
floor stanchion. Top clamp holds pipe securely to
saddle. To complete floor stanchion use with B3088 'A'
pipe stand.
Gussets on sizes C
Finish: Plain. Contact Cooper B-Line for alternative B3097-8 and larger. F
finishes and materials.
Order By: Figure number, pipe size and finish
'D' Shank Diameter
Note: — For vertical adjustment use with Figure Sizes 4” (100mm) thru
A
Shank will fit into nominal 12” (300mm)
B3089 (Pipe Adjuster - page 127) and Figure Schedule 40 pipe size 'E' of
B3088T (Threaded Pipe Stand - page 124). Base Stand Figure B3088
(not included).

C
F

'D' Shank Diameter

Sizes 14” (350mm) thru
Shank will fit into nominal 36” (900mm)
Schedule 40 pipe size 'E' of
Base Stand Figure B3088
(not included).

Pipe Size A B C D E F Bolt Approx. Wt./100

Part No. in. (mm) in. (mm) in. (mm) in. (mm) in. (mm) in. (mm) in. (mm) Size Lbs. (kg)
B3097-4 4" (100) 7" (123.8) 33/16" (65) 2" (50.8) 23/8" (60.3) 21/2" (63.5) 3/4" (19.0) 1/2"-13 1050 (476.4)
B3097-5 5" (125) 85/8" (141.3) 43/16" (65) 2" (50.8) 23/8" (60.3) 21/2" (63.5) 3/4" (19.0) 1/2"-13 1162 (527.1)
B3097-6 6" (150) 11" (177.8) 47/8" (65) 2" (50.8) 23/8" (60.3) 21/2" (63.5) 7/8" (22.2) 5/8"-11 1371 (622.0)
B3097-8 8" (200) 127/8" (231.8) 615/16" (65) 2" (50.8) 23/8" (60.3) 21/2" (63.5) 1" (25.4) 5/8"-11 1751 (794.4)
B3097-10 10" (250) 161/4" (282.6) 715/16" (65) 2" (50.8) 23/8" (60.3) 21/2" (63.5) 1" (25.4) 3/4"-10 2174 (986.3)
B3097-12 12" (300) 181/4" (342.9) 91/8" (65) 3" (76.2) 23/8" (60.3) 21/2" (63.5) 1" (25.4) 3/4"-10 2496 (1132.2)
B3097-14 14" (350) 193/4" (355.6) 101/2" (80) 3" (76.2) 27/8" (73.0) 3" (76.2) 11/8" (28.6) 3/4"-10 5220 (2367.8)
B3097-16 16" (400) 223/4" (406.4) 111/2" (80) 3" (76.2) 27/8" (73.0) 3" (76.2) 11/8" (28.6) 3/4"-10 5965 (2705.6)
B3097-18 18" (450) 257/8" (457.2) 131/2" (100) 4" (101.6) 33/4" (95.2) 4" (101.6) 11/4" (31.7) 3/4"-10 7265 (3295.3)
B3097-20 20" (500) 273/4" (508.0) 141/2" (100) 4" (101.6) 33/4" (95.2) 4" (101.6) 13/8" (34.9) 3/4"-10 7722 (3502.8)
B3097-22 22" (550) 293/4" (609.6) 151/2" (100) 4" (101.6) 33/4" (95.2) 4" (101.6) 13/8" (34.9) 3/4"-10 8336 (3781.3)
B3097-24 24" (600) 33" (609.6) 171/2" (100) 4" (101.6) 33/4" (95.2) 4" (101.6) 15/8" (41.3) 7/8"-9 9583 (4346.8)
B3097-26 26" (650) 35" (762.0) 181/2" (100) 4" (101.6) 33/4" (95.2) 4" (101.6) 2" (50.8) 7/8"-9 9913 (4496.4)
B3097-30 30" (750) 413/8" (762.0) 205/8" (100) 4" (101.6) 33/4" (95.2) 4" (101.6) 2" (50.8) 7/8"-9 13778 (6249.6)
B3097-32 32" (800) 433/8" (762.0) 215/8" (100) 4" (101.6) 33/4" (95.2) 4" (101.6) 2" (50.8) 7/8"-9 14481 (6568.6)
B3097-36 36" (900) 473/8" (1203.2) 235/8" (600.1) 4" (101.6) 33/4" (95.2) 4" (101.6) 2" (50.8) 7/8"-9 15767 (7151.8)

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

136
 Pipe Supports, Guides, Shields & Saddles
Fig. B3098 - Adjustable Pipe Support With U-Bolt (TOLCO Fig. 313)
Size Range: 2" (50mm) thru 12" (300mm) pipe
Material: Steel
Function: Designed to support horizontal pipe from C

Shields & Saddles

Supports, Guides,
floor stanchion where vertical adjustment is required.
U-bolt and hex nuts are provided to hold pipe
securely to saddle.
Maximum Temperature: 650°F (343°C) A
Finish: Plain. Contact Cooper B-Line for alternative
finishes and materials.
Order By: Figure number and finish

8”
(203.2mm)

Pipe Size Max. Pipe O.D. A Bolt Size C Use With B3088 Approx. Wt./100
Part No. in. (mm) in. (mm) in. (mm) B in. (mm) Pipe Stand Lbs. (kg)

B3098-2 2" (50) 23/4" (69.8) 6" (152.4) 7/8"-9 3/8" (9.5) 1" 210 (95.2)
B3098-21/2 21/2" (650) 31/4" (82.5) 61/2" (165.1) 7/8"-9 3/8" (9.5) 1" 219 (99.3)
B3098-3 3" (80) 31/2" (88.9) 63/4" (171.4) 7/8"-9 1/2" (12.7) 1" 240 (108.8)
B3098-31/2 31/2" (90) 31/2" (88.9) 63/4" (171.4) 7/8"-9 1/2" (12.7) 1" 240 (108.8)
B3098-4 4" (100) 41/4" (107.9) 71/2" (190.5) 1"-8 1/2" (12.7) 1" 340 (154.2)
B3098-5 5" (125) 41/2" (114.3) 73/4" (196.8) 1"-8 1/2" (12.7) 1" 360 (163.3)
B3098-6 6" (150) 55/8" (142.9) 83/8" (212.7) 11/4"-7 5/8" (15.9) 11/4" 580 (263.1)
B3098-8 8" (200) 63/4" (171.4) 91/2" (241.2) 11/4"-7 5/8" (15.9) 11/4" 640 (290.3)
B3098-10 10" (250) 8" (203.2) 10" (254.0) 11/4"-7 3/4" (19.0) 11/4" 1060 (480.8)
B3098-12 12" (300) 91/4" (234.9) 111/4" (285.7) 11/4"-7 7/8" (22.2) 11/4" 1060 (480.8)

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

137
 Pipe Supports, Guides, Shields & Saddles
Fig. B3094 - Flange Support (TOLCO Fig. 314) C

Size Range: 4" (100mm) thru 36" (900mm) pipe

Material: Steel
Function: Designed to support 125 lb. cast iron and
Shields & Saddles
Supports, Guides,

150 lb. forged steel flanged connections. (Consult

factory for other flanged bolt patterns). To complete A
floor stanchion, use B3088 pipe stand.
Approvals: Conforms to Federal Specification H
WW-H-171E & A-A-1192A, Type 38 and Gussets on sizes
B3097-8 and larger.
Manufacturers Standardization Society ANSI/MSS
SP-69 & SP-58, Type 37. B
'D' Shank Diameter
Maximum Temperature: 750°F (399°C) Shank will fit into nominal Sizes 4” (100mm) thru
Schedule 40 pipe size 'E' of 12” (300mm)
Finish: Plain
Base Stand Figure B3088
Note: Available in Electro-Galvanized, and Hot Dip (not included).
Galvanized finish or Stainless Steel materials.
Order By: Figure number and finish C

Note: — For vertical adjustment use with Figure

B3089 (Pipe Adjuster - page 127) and Figure B3088T
(Threaded Pipe Stand - page 124).

H
Gussets on sizes B
B3097-8 and larger.

'D' Shank Diameter

Shank will fit into nominal
Schedule 40 pipe size 'E' of Sizes 14” (350mm) thru
Base Stand Figure B3088 36” (900mm)
(not included).

Pipe Size A B C D E H Dia. Approx. Wt./100

Part No. in. (mm) in. (mm) in. (mm) in. (mm) in. (mm) in. (mm) in. (mm) Lbs. (kg)

B3094-4 4" (100) 67/8" (174.5) 2" (50.8) 63/8" (161.9) 23/8" (60.3) 21/2" (63.5) 3/4" (19.0) 707 (320.7)
B3094-5 5" (125) 73/8" (187.3) 2" (50.8) 71/16" (179.4) 23/8" (60.3) 21/2" (63.5) 7/8" (22.2) 775 (351.5)
B3094-6 6" (150) 73/8" (187.3) 2" (50.8) 73/4" (196.8) 23/8" (60.3) 21/2" (63.5) 7/8" (22.2) 844 (382.8)
B3094-8 8" (200) 101/8" (257.2) 2" (50.8) 99/16" (242.9) 23/8" (60.3) 21/2" (63.5) 7/8" (22.2) 1429 (648.2)
B3094-10 10" (250) 113/8" (288.8) 2" (50.8) 8" (203.2) 23/8" (60.3) 21/2" (63.5) 1" (25.4) 1250 (567.0)
B3094-12 12" (300) 127/8" (327.0) 3" (76.2) 91/2" (241.3) 23/8" (60.3) 21/2" (63.5) 1" (25.4) 1446 (655.9)
B3094-14 14" (350) 15" (381.0) 3" (76.2) 183/16" (462.0) 27/8" (73.0) 3" (76.2) 11/8" (28.6) 3149 (1429.4)
B3094-16 16" (400) 161/4" (412.7) 3" (76.2) 165/8" (422.3) 27/8" (73.0) 3" (76.2) 11/8" (28.6) 3068 (1391.6)
B3094-18 18" (450) 18" (457.2) 4" (101.6) 1711/16" (449.3) 33/4" (95.2) 4" (101.6) 11/4" (31.7) 3339 (1514.6)
B3094-20 20" (500) 191/4" (488.9) 4" (101.6) 153/4" (400.0) 33/4" (95.2) 4" (101.6) 11/4" (31.7) 2994 (1358.1)
B3094-24 24" (600) 221/2" (571.5) 4" (101.6) 183/8" (466.7) 33/4" (95.2) 4" (101.6) 13/8" (34.9) 4255 (1930.0)
B3094-30 30" (750) 257/8" (657.2) 4" (101.6) 163/8" (415.9) 33/4" (95.2) 4" (101.6) 13/8" (34.9) 5210 (2363.2)
B3094-36 36" (900) 291/2" (749.3) 4" (101.6) 171/2" (444.5) 33/4" (95.2) 4" (101.6) 15/8" (41.3) 5382 (2441.3)

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

138
 Pipe Supports, Guides, Shields & Saddles
Fig. B3195 - I.P.S. Isolator (TOLCO Fig. 84) C
Fig. B3195CT - Copper Tubing Isolator (TOLCO Fig. 83)
B

Size Range:

Shields & Saddles

Supports, Guides,
B3195 - 3⁄8" (10mm) thru 8" (200mm) pipe
B3195CT - 3⁄8" (10mm) thru 4" (100mm) pipe
Material: Pre-Galvanized steel and felt
Function: A non-conductive felt lining serves to dampen
sound vibration and prevent transmission of sound to the
building structure.
Finish: Pre-Galvanized A
Standard Steel Pipe Hangers for use with Isolators:
B3100 clevis hanger, B3170 band hanger, B3690
J-hanger and B2000 Series rigid or O.D. pipe clamps
Order By: Figure number and finish

Pipe Size A B C Hanger Size Strut Clamp Approx. Wt./100

Part No. in. (mm) in. (mm) in. (mm) in. (mm) in. (mm) Lbs. (kg)

B3195-3/8 3/8" (10) 11/8" (28.6) 11/4" (31.7) 21/4" (57.1) 1" (25) 1" (25) Rigid 4 (1.8)
B3195-1/2 1/2" (15) 13/8" (34.9) 11/4" (31.7) 21/4" (57.1) 1" (25) 1" (25) Rigid 4 (1.8)
B3195-3/4 3/4" (20) 11/2" (38.1) 11/4" (31.7) 21/4" (57.1) 1
1 /4" (32) 11/4" (32) O.D. 6 (2.7)
B3195-1 1" (25) 113/16" (46.0) 11/4" (31.7) 21/4" (57.1) 11/2" (40) 11/2" (38) O.D. 10 (4.5)
B3195-11/4 11/4" (32) 21/8" (54.0) 11/4" (31.7) 21/4" (57.1) 2" (50) 2" (51) O.D. 10 (4.5)
B3195-11/2 11/2" (40) 23/8" (60.3) 11/4" (31.7) 21/4" (57.1) 2" (50) 2" (50) Rigid 12 (5.4)
B3195-2 2" (50) 27/8" (73.0) 11/4" (31.7) 21/4" (57.1) 1
2 /2" (65) 21/2" (65) Rigid 14 (6.3)
B3195-21/2 21/2" (65) 33/8" (85.7) 11/4" (31.7) 3" (76.2) 3" (80) 3" (76) O.D. 20 (9.1)
B3195-3 3" (80) 4" (101.6) 11/4" (31.7) 3" (76.2) 31/2" (90) 31/2" (90) Rigid 25 (11.3)
B3195-31/2 31/2" (90) 41/2" (114.3) 11/4" (31.7) 3" (76.2) 4" (100) 4" (100) Rigid 36 (16.3)
B3195-4 4" (100) 51/2" (139.7) 11/4" (31.7) 1
3 /2" (88.9) 5" (125) 5" (125) Rigid 65 (29.5)
B3195-5 5" (125) 61/2" (165.1) 11/4" (31.7) 4" (101.6) 6" (150) 6" (150) Rigid 67 (30.4)
B3195-6 6" (150) 75/8" (193.7) 21/8" (54.0) 51/2" (139.7) 8" (200) 75/8" (193) O.D. 196 (88.9)
B3195-8 8" (200) 95/8" (244.5) 21/8" (54.0) 51/2" (139.7) 10" (250) 95/8" (244) O.D. 210 (95.2)

Pipe Size A B C Hanger Size Strut Clamp Approx. Wt./100

Part No. in. (mm) in. (mm) in. (mm) in. (mm) in. (mm) Lbs. (kg)
B3195CT-3/8 3/8" (10) 1" (25.4) 11/4" (31.7) 21/4" (57.1) 3/4" (20) 11/8" (28) O.D. 4 (1.8)
B3195CT-1/2 1/2" (15) 1
1 /8" (28.6) 11/4" (31.7) 21/4" (57.1) 3/4" (20) 11/8" (28) O.D. 4 (1.8)
B3195CT-3/4 3/4" (20) 13/8" (34.9) 11/4" (31.7) 21/4" (57.1) 1" (25) 1" (25) Rigid 4 (1.8)
B3195CT-1 1" (25) 15/8" (41.3) 11/4" (31.7) 21/4" (57.1) 11/4" (32) 11/2" (38) O.D. 6 (2.7)
B3195CT-11/4 11/4" (32) 17/8" (47.6) 11/4" (31.7) 21/4" (57.1) 11/2" (40) 13/4" (44) O.D. 10 (4.5)
B3195CT-11/2 11/2" (40) 21/8" (54.0) 11/4" (31.7) 21/4" (57.1) 2" (50) 21/8" (54) O.D. 10 (4.5)
B3195CT-2 2" (50) 25/8" (66.7) 11/4" (31.7) 21/4" (57.1) 21/2" (65) 25/8" (66) O.D. 12 (5.4)
B3195CT-21/2 21/2" (65) 31/8" (79.4) 11/4" (31.7) 21/4" (57.1) 3" (80) 31/8" (79) O.D. 13 (5.9)
B3195CT-3 3" (80) 35/8" (92.1) 11/4" (31.7) 21/4" (57.1) 3" (80) 3" (80) Rigid 15 (6.8)
B3195CT-31/2 1
3 /2" (90) 41/8" (104.8) 11/4" (31.7) 21/4" (57.1) 1
3 /2" (90) 1
3 /2" (90) Rigid 28 (12.7)
B3195CT-4 4" (100) 51/8" (130.2) 11/4" (31.7) 21/4" (57.1) 5" (125) 5" (127) O.D. 44 (19.9)

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

139
 Pipe Supports, Guides, Shields & Saddles

Fig. B3281 thru B3287 - Pipe Alignment Guide (TOLCO Fig. 420 thru Fig. 426)
X
Size Range: For use with 11⁄2" (40mm) thru 24" (600mm) pipe
Material: Steel
Shields & Saddles
Supports, Guides,

Finish: Black Primer T

Overall Height
Function: Designed for use in directing thermal expansion of
R
insulated or non-insulated pipe in the direction permitted by
Center of pipe to
expansion joints or loops. The use of two or more guides on both W bottom of legs.
sides of an expansion joint or loop is recommended. Pipe lines Overall Width
should be supported with hangers or rollers so that when properly U T
installed, the guides will not be supporting any pipe loads. V R
Maximum operating temperature should not exceed 750oF (399°C). S Dia.
Order By: Figure number and finish. For use with copper tubing, 4 Holes
add CT suffix to the part number.

Body R S T U V
Size in. (mm) in. (mm) in. (mm) in. (mm) in. (mm)

001 31/2" (88.9) 5/8" (15.9) 57/8" (149.2) 41/8" (104.8) 13/4" (44.4)
002 4" (101.6) 5/8" (15.9) 63/4" (171.4) 43/8" (111.1) 13/4" (44.4)
003 43/8" (111.1) 5/8" (15.9) 75/8" (193.7) 51/8" (130.2) 13/4" (44.4)
004 51/4" (133.3) 5/8" (15.9) 91/4" (234.9) 61/8" (155.6) 13/4" (44.4)
005 61/4" (158.7) 5/8" (15.9) 115/8" (295.3) 7" (177.8) 23/4" (69.8)
006 7" (177.8) 5/8" (15.9) 133/8" (339.7) 81/4" (209.5) 23/4" (69.8)
007 77/8" (200.0) 3/4" (19.0) 151/8" (384.2) 97/8" (250.8) 4" (101.6)
008 87/8" (225.4) 3/4" (19.0) 17" (431.8) 107/8" (276.2) 4" (101.6)
009 93/4" (247.6) 3/4" (19.0) 183/4" (476.2) 117/8" (301.6) 4" (101.6)
010 107/8" (276.2) 3/4" (19.0) 21" (533.4) 113/4" (298.4) 6" (152.4)
011 121/8" (308.0) 7/8" (22.2) 231/8" (587.4) 141/2" (368.3) 6" (152.4)
012 13" (330.2) 7/8" (22.2) 25" (635.0) 151/2" (393.7) 6" (152.4)
013 143/4" (374.6) 11/8" (28.6) 273/4" (704.8) 171/8" (435.0) 6" (152.4)
014 161/2" (419.1) 11/8" (28.6) 311/2" (800.1) 191/4" (488.9) 6" (152.4)

Body W X Approx. Wt./100

Size in. (mm) in. (mm) Lbs. (kg) Note: CT sizes have
001 61/8" (155.6) 3" (76.2) 700 (317.5) lead shims between
the steel clamp and
002 71/8" (181.0) 3" (76.2) 800 (362.9)
the copper tubing.
003 81/8" (206.4) 3" (76.2) 900 (408.2)
004 101/8" (257.2) 3" (76.2) 1100 (498.9) Guides with greater
005 121/8" (308.0) 4" (101.6) 1700 (771.1) allowable movement
available, Contact
006 141/8" (358.8) 4" (101.6) 2000 (907.2)
B-Line Engineering
007 161/8" (409.6) 6" (152.4) 4000 (1814.4) for more information.
008 181/8" (460.4) 6" (152.4) 4800 (2177.3)
009 201/8" (511.2) 6" (152.4) 5400 (2449.4)
010 221/8" (562.0) 8" (203.2) 6100 (2766.9)
011 241/8" (612.8) 8" (203.2) 8900 (4037.0)
012 261/8" (663.6) 8" (203.2) 10200 (4626.7)
013 281/8" (714.4) 8" (203.2) 11000 (4989.6)
014 321/8" (816.0) 8" (203.2) 15000 (6804.0)
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

140
 Pipe Supports, Guides, Shields & Saddles
Fig. B3281 thru B3287 - Pipe Alignment Guide (TOLCO Fig. 420 thru Fig. 426) (Continued)
Insulation Thickness
Pipe Size 1" (25.4mm) 11/2" (38.1mm) 2" (50.8mm) 21/2" (63.5mm)
Part No. BS* SAM** Part No. BS* SAM** Part No. BS* SAM** Part No. BS* SAM**

Shields & Saddles

Supports, Guides,
1/2" (15) B3281-1/2 001 4" (101.6) B3281-1/2 001 4" (101.6) B3283-1/2 002 4" (101.6) B3284-1/2 003 4" (101.6)
3/4" (20) B3281-3/4 001 4" (101.6) B3282-3/4 002 4" (101.6) B3283-3/4 003 4" (101.6) B3284-3/4 004 4" (101.6)
1" (25) B3281-1 001 4" (101.6) B3282-1 002 4" (101.6) B3283-1 003 4" (101.6) B3284-1 004 4" (101.6)
11/4" (32) B3281-11/4 001 4" (101.6) B3282-11/4 002 4" (101.6) B3283-11/4 003 4" (101.6) B3284-11/4 004 4" (101.6)
11/2" (40) B3281-11/2 002 4" (101.6) B3281-11/2 002 4" (101.6) B3283-11/2 003 4" (101.6) B3284-11/2 004 4" (101.6)
2" (50) B3281-2 002 4" (101.6) B3282-2 003 4" (101.6) B3283-2 004 4" (101.6) B3283-2 004 4" (101.6)
21/2" (65) B3281-21/2 003 4" (101.6) B3281-21/2 003 4" (101.6) B3283-21/2 004 4" (101.6) B3283-21/2 004 4" (101.6)
3" (80) B3281-3 003 4" (101.6) B3282-3 004 4" ((101.6) B3283-3 004 4" (101.6) B3284-3 005 4" (101.6)
4" (100) B3281-4 004 4" (101.6) B3281-4 004 4" (101.6) B3283-4 005 4" (101.6) B3284-4 005 4" (101.6)
5" (125) B3281-5 005 4" (101.6) B3281-5 005 4" (101.6) B3281-5 005 4" (101.6) B3284-5 006 4" (101.6)
6" (150) B3281-6 005 4" (101.6) B3281-6 005 4" (101.6) B3283-6 006 4" (101.6) B3283-6 006 4" (101.6)
8" (200) B3281-8 006 4" (101.6) B3281-8 006 4" (101.6) B3283-8 007 6" (152.4) B3284-8 008 6" (152.4)
10" (250) B3281-10 008 6" (152.4) B3281-10 008 6" (152.4) B3281-10 008 6" (152.4) B3284-10 009 6" (152.4)
12" (300) B3281-12 009 6" (152.4) B3281-12 009 6" (152.4) B3281-12 009 6" (152.4) B3284-12 010 6" (152.4)
14" (350) B3281-14 010 6" (152.4) B3281-14 010 6" (152.4) B3281-14 010 6" (152.4) B3281-14 010 6" (152.4)
16" (400) B3281-16 011 8" (203.2) B3281-16 011 8" (203.2) B3281-16 011 8" (203.2) B3281-16 011 8" (203.2)
18" (450) B3281-18 012 8" (203.2) B3281-18 012 8" (203.2) B3281-18 012 8" (203.2) B3281-18 012 8" (203.2)
20" (500) B3281-20 013 8" (203.2) B3281-20 013 8" (203.2) B3281-20 013 8" (203.2) B3281-20 013 8" (203.2)
24" (600) B3281-24 014 8" (203.2) B3281-24 014 8" (203.2) B3281-24 014 8" (203.2) B3281-24 014 8" (203.2)

Insulation Thickness
Nominal 3" (76.2) 31/2" (88.9) 4" (101.6)
Pipe Size Part No. BS* SAM** Part No. BS* SAM** Part No. BS* SAM**
1/2" (15) B3285-1/2 004 4" (101.6) B3285-1/2 004 4" (101.6) B3287-1/2 005 4" (101.6)
3/4" (20) B3284-3/4 004 4" (101.6) B3286-3/4 005 4" (101.6) B3286-3/4 005 4" (101.6)
1" (25) B3284-1 004 4" (101.6) B3286-1 005 4" (101.6) B3286-1 005 4" (101.6) BS* = Body Size
1
1 /4" (32) B3284-11/4 004 4" (101.6) B3286-11/4 005 4" (101.6) B3286-11/4 005 4" (101.6)
SAM** = Standard
11/2" (40) B3284-11/2 004 4" (101.6) B3286-11/2 005 4" (101.6) B3286-11/2 005 4" (101.6) Allowable Movement
2" (50) B3285-2 005 4" (101.6) B3285-2 005 4" (101.6) B3287-2 006 4" (101.6)
1
2 /2" (65) B3285-21/2 005 4" (101.6) B3285-21/2 005 4" (101.6) B3287-21/2 006 4" (101.6) Note: Use 1”
3" (80) B3284-3 005 4" (101.6) B3286-3 006 4" (101.6) B3286-3 006 4" (101.6) (25.4mm) insulation
thickness column
4" (100) B3285-4 006 4" (101.6) B3286-4 006 4" (101.6) B3287-4 007 6" (152.4)
when no insulation is
5" (125) B3284-5 006 4" (101.6) B3286-5 007 6" (152.4) B3287-5 008 6" (152.4) present.
6" (150) B3285-6 007 6" (152.4) B3286-6 008 6" (152.4) B3286-6 008 6" (152.4)
8" (200) B3284-8 008 6" (152.4) B3286-8 009 6" (152.4) B3286-8 009 6" (152.4)
10" (250) B3284-10 009 6" (152.4) B3286-10 010 6" (152.4) B3286-10 010 6" (152.4)
12" (300) B3284-12 010 6" (152.4) B3286-12 011 6" (152.4) B3286-12 011 6" (152.4)
14" (350) B3285-14 011 8" (203.2) B3285-14 011 8" (203.2) B3287-14 012 8" (203.2)
16" (400) B3285-16 012 8" (203.2) B3285-16 012 8" (203.2) B3287-16 013 8" (203.2)
18" (450) B3285-18 013 8" (203.2) B3285-18 013 8" (203.2) B3287-18 014 8" (203.2)
20" (500) B3285-20 014 8" (203.2) B3285-20 014 8" (203.2) B3285-20 014 8" (203.2)
24" (600) --- --- --- --- --- --- --- --- --- --- --- ---

Installation: Attach outer housing of the first pipe guide to the structure a maximum of four pipe diameters from an expansion joint.
The second pipe guide should be located a maximum of 14 pipe diameters from the first pipe guide. The spider pipe clamp should be
offset at a minimum of half the distance in the opposite direction of the axial expansion. See chart for Standard Allowable Movement (SAM).

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

141
 Pipe Supports, Guides, Shields & Saddles
Fig. B2417 - Strut Mounted Pipe Guide
Material: Steel
Finish: Electro-Galvanized
Function: Designed as a guide to permit
Shields & Saddles
Supports, Guides,

longitudinal movement of pipe.

Order By: Figure number and finish.
(Includes guide and pipe clamp).

Clearance

Pipe Size Min. Radial Clearance Includes Approx. Wt./100

Part No. in. (mm) in. (mm) Lbs. (kg)
B2417-1/2 1/2" (15) 1/16" (1.6) B2009 22 (10.0)
B2417-3/4 3/4" (20) 1/16" (1.6) B2010 25 (11.3)
B2417-1 1" (25) 3/32" (2.3) B2034 30 (13.6) Note: Strut Mounted Pipe
B2417-11/4 11/4" (32) 3/32" (2.3) B2037 47 (21.8) Guides are available for
copper tubing: B2417CT-Size
B2417-11/2 11/2" (40) 3/32" (2.3) B2039 51 (23.1)
B2417-2 2" (50) 1/8" (3.2) B2043 62 (28.1)
B2417-21/2 21/2" (65) 1/8" (3.2) B2047 69 (31.3)
B2417-3 3" (80) 5/32" (3.9) B2016 108 (49.0)
B2417-31/2 31/2" (90) 5/32" (3.9) B2017 118 (53.5)
B2417-4 4" (100) 5/32" (3.9) B2018 128 (58.0)

Fig. B3147A & B3147B - Pipe Anchor (TOLCO Fig. 32) U-Bolt Dia.
(dimensional charts on following page)

Size Range: For use with 1⁄2" (15mm) thru 24" (600mm) pipe
Material: Steel
B
C
Function: Recommended for anchoring pipe to structure. Type A
Finish: Plain
A
Center of pipe to
Note: 1⁄2" (15mm) thru 4" (100mm), use U-bolt to fasten chair to
bottom of base
support; 5" (125mm) thru 24" (600mm) U-bolt attaches directly plate.
to support structure.
Holes are provided in chair for fastening to support if
required. 13/16” (30.2mm) x
U-Bolt Dia.
11/16” (27.0mm)
Available in Electro-Galvanized and Hot Dip Galvanized 2 Holes
finish or Stainless Steel materials. D

Order By: Figure number and pipe size

B C Type B

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

142
 Pipe Supports, Guides, Shields & Saddles
Fig. B3147A & B3147B - Pipe Anchor (TOLCO Fig. 32) cont.

Shields & Saddles

Supports, Guides,
Type A Type B

Part No. Pipe Size U-Bolt Dia. A B C D Approx. Wt./100

in. (mm) in. (mm) in. (mm) in. (mm) in. (mm) in. (mm) Lbs. (kg)

B3147A-1/2 1/2" (15) 3/8" (9.4) 15/16" (23.8) 2" (50.8) 13/16" (30.2) -- (--) 80 (36.3)
B3147A-3/4 3/4" (20) 3/8" (9.4) 11/16" (27.0) 23/8" (60.3) 13/8" (34.9) -- (--) 88 (39.9)
B3147A-1 1" (25) 3/8" (9.4) 13/16" (30.2) 25/8" (66.7) 13/8" (34.9) -- (--) 96 (43.5)
B3147A-11/4 1
1 /4" (32) 3/8" (9.4) 13/8" (34.9) 27/8" (73.0) 21/16" (52.4) -- (--) 107 (48.5)
B3147A-11/2 11/2" 3/8" 19/16" 31/4" 23/8" -- 118

Type A
(40) (9.4) (39.7) (82.5) (60.3) (--) (53.5)
B3147A-2 2" (50) 3/8" (9.4) 13/4" (44.4) 33/8" (85.7) 212/16" (71.4) -- (--) 132 (59.9)
B3147A-21/2 21/2" (65) 1/2" (12.7) 2" (50.8) 415/16" (125.4) 37/16" (87.3) -- (--) 175 (79.4)
B3147A-3 3" (80) 1/2" (12.7) 23/8" (60.3) 59/16" (141.3) 41/16" (103.2) -- (--) 215 (97.5)
B3147A-31/2 1
3 /2" (90) 1/2" (12.7) 23/8" (60.3) 61/16" (154.0) 49/16" (115.9) -- (--) 240 (108.8)
B3147A-4 4" (100) 1/2" (12.7) 27/8" (73.0) 69/16" (166.7) 51/16" (128.6) -- (--) 265 (120.2)
B3147B-5 5" (125) 1/2" (12.7) 37/16" (87.3) 4" (101.6) 61/8" (156.2) 21/4" (57.1) 290 (131.5)
B3147B-6 6" (150) 5/8" (15.9) 4" (101.6) 5" (127.0) 73/8" (187.3) 3" (76.2) 315 (142.9)
B3147B-8 8" (200) 5/8" (15.9) 51/4" (133.3) 7" (177.9) 93/8" (138.0) 51/2" (139.7) 885 (401.4)
B3147B-10 10" (250) 3/4" (19.0) 67/16" (164.1) 8" (203.2) 113/8" (288.8) 51/2" (139.7) 1050 (476.3) Type B
B3147B-12 12" (300) 7/8" (22.2) 71/2" (190.5) 9" (228.6) 133/4" (349.2) 6" (152.4) 1210 (548.8)
B3147B-14 14" (350) 7/8" (22.2) 83/16" (208.0) 10" (254.0) 15" (381.0) 7" (177.9) 1480 (671.3)
B3147B-16 16" (400) 7/8" (22.2) 91/4" (234.9) 10" (254.0) 17" (431.8) 7" (177.9) 1735 (787.0)
B3147B-18 18" (450) 1" (25.4) 103/8" (263.5) 11" (279.4) 191/8" (485.8) 7" (177.9) 2011 (912.2)
B3147B-20 20" (500) 1" (25.4) 113/8" (288.9) 12" (304.8) 211/8" (536.6) 7" (177.9) 2332 (1057.8)
B3147B-24 24" (600) 1" (25.4) 135/8" (346.1) 12" (304.8) 251/8" (638.2) 8" (203.2) 2550 (1156.7)

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

143
 Pipe Supports, Guides, Shields & Saddles
Fig. B3256 Hold-Down Anchor Clamp (TOLCO Fig. 405)
Size Range: 2" (50mm) thru 30" (750mm) pipe H
2 Holes
Material: Steel Steel Size Steel Size

Function: Designed to prevent longitudinal or lateral

Shields & Saddles
Supports, Guides,

R R
movement of pipe where pipe is anchored to concrete E
piers or other supporting structures. H
C A A 4 Holes
Finish: Plain or Electro-Galvanized C
B
Order By: Figure number and finish. B
D
D
D
B3256-2 thru B3256-8 B3256-10 thru B3256-30

Pipe Size A B C D E
Part No. in. (mm) in. (mm) in. (mm) in. (mm) in. (mm) in. (mm)
B3256-2 2" (50) 15/16" (23.8) 81/8" (206.4) 57/8" (149.2) 11/2" (38.1) - -
B3256-21/2 21/2" (65) 13/16" (30.2) 85/8" (219.1) 63/8" (161.9) 11/2" (38.1) - -
B3256-3 3" (50) 11/2" (38.1) 91/4" (234.9) 7" (177.8) 11/2" (38.1) - -
B3256-31/2 31/2" (80) 13/4" (44.4) 93/4" (247.6) 71/2" (190.5) 11/2" (38.1) - -
B3256-4 4" (90) 2" (50.8) 101/4" (260.3) 8" (203.2) 11/2" (38.1) - -
B3256-5 5" (100) 29/16" (65.1) 115/16" (287.3) 91/16" (230.2) 11/2" (38.1) - -
B3256-6 6" (150) 31/16" (77.8) 139/16" (346.1) 105/8" (269.9) 3" (76.2) - -
B3256-8 8" (200) 41/16" (103.2) 153/4" (396.9) 125/8" (320.7) 3" (76.2) - -
B3256-10 10" (250) 51/8" (130.2) 183/4" (476.2) 151/4" (387.3) 21/2" (63.5) 1/2" (12.7)
B3256-12 12" (300) 61/8" (155.6) 203/4" (527.0) 171/4" (438.1) 21/2" (63.5) 1/2" (12.7)
B3256-14 14" (350) 63/4" (171.4) 22" (558.8) 181/2" (469.9) 3" (76.2) 1/2" (12.7)
B3256-16 16" (400) 73/4" (196.8) 24" (609.6) 201/2" (520.7) 3" (76.2) 1/2" (12.7)
B3256-18 18" (450) 83/4" (222.2) 26" (660.4) 221/2" (571.2) 31/2" (88.9) 1/2" (12.7)
B3256-20 20" (500) 93/4" (247.6) 28" (711.2) 241/2" (622.3) 31/2" (88.9) 1/2" (12.7)
B3256-24 24" (600) 113/4" (298.4) 32" (812.8) 281/2" (723.9) 31/2" (88.9) 1/2" (12.7)
B3256-30 30" (750) 143/4" (374.6) 38" (965.2) 341/2" (876.3) 31/2" (88.9) 1/2" (12.7)

H R Steel Size Approx. Wt./100

Part No. in. (mm) in. (mm) in. (mm) Lbs. (kg)
B3256-2 7/8" (22.2) 13/16" (30.2) 3/8" x 3" (9.5 x 76.2) 342 (155.1)
B3256-21/2 7/8" (22.2) 17/16" (36.5) 3/8" x 3" (9.5 x 76.2) 386 (175.1)
B3256-3 7/8" (22.2) 13/4" (44.4) 3/8" x 3" (9.5 x 76.2) 434 (196.8)
B3256-31/2 7/8" (22.2) 2" (50.8) 3/8" x 3" (9.5 x 76.2) 478 (216.8)
B3256-4 7/8" (22.2) 21/4" (57.1) 3/8" x 3" (9.5 x 76.2) 518 (234.9)
B3256-5 7/8" (22.2) 213/16" (71.4) 3/8" x 3" (9.5 x 76.2) 610 (276.7)
B3256-6 1" (25.4) 35/16" (84.1) 1/2" x 6" (12.7 x 152.4) 1961 (889.5)
B3256-8 1" (25.4) 45/16" (109.5) 1/2" x 6" (12.7 x 152.4) 2397 (1087.3)
B3256-10 11/8" (28.6) 53/8" (136.5) 1/2" x 8" (12.7 x 203.2) 4155 (1884.7)
B3256-12 11/8" (28.6) 63/8" (161.9) 1/2" x 8" (12.7 x 203.2) 4789 (2172.3)
B3256-14 11/8" (28.6) 7" (177.8) 1/2" x 10" (12.7 x 254.0) 6421 (2912.5)
B3256-16 11/8" (28.6) 8" (203.2) 1/2" x 10" (12.7 x 254.0) 7210 (3270.4)
B3256-18 11/8" (28.6) 9" (228.6) 1/2" x 12" (12.7 x 304.8) 9509 (4313.3)
B3256-20 11/8" (28.6) 10" (254.0) 1/2" x 12" (12.7 x 304.8) 10434 (4732.8)
B3256-24 11/8" (28.6) 12" (304.8) 1/2" x 12" (12.7 x 304.8) 12295 (5577.0)
B3256-30 11/8" (28.6) 15" (381.0) 1/2" x 12" (12.7 x 304.8) 15082 (6841.2)

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

144
 Pipe Supports, Guides, Shields & Saddles
Steel Size
Fig. B3257 - Base Plate (TOLCO Fig. 406) H
4 Holes
Size Range: 2" (50mm) thru 30" (750mm) pipe
B A
Material: Steel A

Function: Designed as a base plate for B3256

Shields & Saddles

Supports, Guides,
pipe anchor. H C
B
2 Holes D
Finish: Plain or Electro-Galvanized D E
Steel Size C D
Order By: Figure part number and finish.
B3257-2 thru B3257-8 B3257-10 thru B3257-30

Pipe Size A B C D
Part No. in. (mm) in. (mm) in. (mm) in. (mm) in. (mm)

B3257-2 2" (50) 81/8" (206.4) 57/8" (149.2) 11/8" (28.6) 11/2" (38.1)
B3257-21/2 21/2" (65) 85/8" (219.1) 63/8" (161.9) 11/8" (28.6) 11/2" (38.1)
B3257-3 3" (80) 91/4" (234.9) 7" (177.8) 11/8" (28.6) 11/2" (38.1)
B3257-31/2 31/2" (90) 93/4" (247.6) 71/2" (190.5) 11/8" (28.6) 11/2" (38.1)
B3257-4 4" (100) 101/4" (260.3) 8" (203.2) 11/8" (28.6) 11/2" (38.1)
B3257-5 5" (125) 115/16" (287.3) 91/16" (230.2) 11/8" (28.6) 11/2" (38.1)
B3257-6 6" (150) 135/8" (346.1) 105/8" (269.9) 11/2" (38.1) 3" (76.2)
B3257-8

30" (750) 38" (965.2) 341/2" (876.3) 13/4" (44.4) 21/2" (6

E H Steel Size Approx. Wt./100

Part No. in. (mm) in. (mm) in. (mm) Lbs. (kg)

B3257-2 - - 7/8" (22.2) 3/8" x 3" (9.5 x 76.2) 246 (111.6)

B3257-21/2 - - 7/8" (22.2) 3/8" x 3" (9.5 x 76.2) 262 (118.8)
B3257-3 - - 7/8" (22.2) 3/8" x 3" (9.5 x 76.2) 282 (127.9)
B3257-31/2 - - 7/8" (22.2) 3/8" x 3" (9.5 x 76.2) 298 (135.2)
B3257-4 - - 7/8" (22.2) 3/8" x 3" (9.5 x 76.2) 314 (142.4)
B3257-5 - - 7/8" (22.2) 3/8" x 3" (9.5 x 76.2) 348 (157.8)
B3257-6 - - 1" (25.4) 1/2" x 6" (12.7 x 152.4) 1137 (515.7)
B3257-8 - - 1" (25.4) 1/2" x 6" (12.7 x 152.4) 1307 (592.8)
B3257-10 5" (127.0) 11/8" (28.6) 1/2" x 8" (12.7 x 203.2) 2071 (939.4)
B3257-12 5" (127.0) 11/8" (28.6) 1/2" x 8" (12.7 x 203.2) 2298 (1042.4)
B3257-14 6" (152.4) 11/8" (28.6) 1/2" x 8" (12.7 x 254.0) 3064 (1389.8)
B3257-16 6" (152.4) 11/8" (28.6) 1/2" x 8" (12.7 x 254.0) 3347 (1518.2)
B3257-18 7" (177.8) 11/8" (28.6) 1/2" x 12" (12.7 x 304.8) 4368 (1981.3)
B3257-20 7" (177.8) 11/8" (28.6) 1/2" x 12" (12.7 x 304.8) 4709 (2136.0)
B3257-24 7" (177.8) 11/8" (28.6) 1/2" x 12" (12.7 x 304.8) 5389 (2444.4)
B3257-30 7" (177.8) 11/8" (28.6) 1/2" x 12" (12.7 x 304.8) 6410 (2907.6)

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

145
 Pipe Supports, Guides, Shields & Saddles
Fig. B3891 - B3897 Pipe Slide Assembly Series (TOLCO Fig. 424 thru Fig. 431)
Material: Tee - Steel;
Facing Plate - Stainless Steel Type 304;
Base - Steel with 3/32” (2.4mm) thick Teflon®† slide
Shields & Saddles
Supports, Guides,

pads.
Finish: Black paint.
Service: Designed to support pipe where
horizontal movement from expansion and
contraction is present. Fits up to 3” (76.2mm)
insulation thickness.
Approvals: Conforms to Federal Specification
B3891 - 10 - CL WW-H-171E & A-A-1192A and Manufacturers
Standardization Society ANSI/MSS SP-69 & SP-58,
Type 35.
Base Style Travel Options Operating Temperature Rating:
1 04” (101) (except B3897) Standard Slide = Blank 400°F (204°C) maximum
2 10” (254) (except B3897) W/ End Plates = EP - Pipe Size
3 21/2” (63) (B3897 only) W/ B3140 Clamps = CL - Pipe Size Loading: Capable of supporting constant loads up
4 to 2000 Psi at 70°F (21°C).
5 † Mark shown in this document is the property of its respective owner.
6
7

B3891 B3892 B3893 B3894 B3895

Notes:
B3891, B3892 and B3893 are designed for longitudinal movement only.
B3894, B3895 and B3896 are designed for longitudinal and limited
transverse movement.
B3897 is designed for up to 5 inches (127mm) of horizontal movement in
any direction, depending on the installed position.
B3896 B3897

Options:

End Plates B3140 Clamps

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

146
 Pipe Supports, Guides, Shields & Saddles
Fig. B3891 - B3897 - Pipe Slide Assembly Series (TOLCO Fig. 424 thru Fig. 431)

Shields & Saddles

Supports, Guides,
Pipe Travel Height H Length L Depth B Diameter D
Size In. (mm) Part No. In. (mm) In. (mm) In. (mm) In. (mm)

21/2” (63.5) B3897 55/16" (134.9) 91/2" (241.3) 5" (127.0) 4" (101.6)
B3891 45/8" (117.5) 6" (152.4) 2" (50.8) N/A N/A
B3892 51/8" (130.2) 6" (152.4) 4" (101.6) N/A N/A
B3893 51/8" (130.2) 6" (152.4) 4" (101.6) N/A N/A
4" (127.0)
B3894 45/8" (117.5) 6" (152.4) 2" (50.8) N/A N/A
B3895 51/8" (130.2) 6" (152.4) 4" (101.6) N/A N/A
1" to 24" B3896 51/8" (130.2) 6" (152.4) 4" (101.6) N/A N/A
(25 to 600) B3891 45/8" (117.5) 12" (304.8) 2" (50.8) N/A N/A
B3892 51/8" (130.2) 12" (304.8) 4" (101.6) N/A N/A
B3893 51/8" (130.2) 12" (304.8) 4" (101.6) N/A N/A
10" (254.0)
B3894 45/8" (117.5) 12" (304.8) 2" (50.8) N/A N/A
B3895 51/8" (130.2) 12" (304.8) 4" (101.6) N/A N/A
B3896 51/8" (130.2) 12" (304.8) 4" (101.6) N/A N/A

Max
Pipe Travel Width P Width W Recommended Load
Size In. mm Part No. In. mm In. mm Lbs. kN

21/2” (63.5) B3897 N/A N/A 91/2" (241.3) 16000 (71.2)

B3891 4" (101.6) N/A N/A 12000 (53.4)
B3892 4" (101.6) 7" (177.8) 12000 (53.4)
B3893 4" (101.6) 7" (177.8) 12000 (53.4)
4" (127.0)
B3894 N/A N/A 6" (152.4) 12000 (53.4)
B3895 6" (152.4) 10" (254.0) 24000 (106.8)
1" to 24" B3896 6" (152.4) 10" (254.0) 24000 (106.8)
(25 to 600) B3891 4" (101.6) N/A N/A 12000 (53.4)
B3892 4" (101.6) 7" (177.8) 12000 (53.4)
B3893 4" (101.6) 7" (177.8) 12000 (53.4)
10" (254.0)
B3894 N/A N/A 6" (152.4) 12000 (53.4)
B3895 6" (152.4) 10" (254.0) 24000 (106.8)
B3896 6" (152.4) 10" (254.0) 24000 (106.8)

*Based on Teflon® † of 500 psi.

† Mark shown in this document is the property of its respective owner.

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

147
 Pipe Supports, Guides, Shields & Saddles
Fig. B3891 - B3897 - Pipe Slide Assembly Series (TOLCO Fig. 424 thru Fig. 431)
Shields & Saddles
Supports, Guides,

Field weld
Field weld
pipe to tee.
pipe to tee.
H
H Stainless steel facing
Stainless steel facing
plate on tee - filled
plate on tee - filled
Teflon® on base.
Teflon® on base.
P W

B3891 Front View B3894 Front View

B
L

B3891& B3894 Side View

Field weld Field weld

pipe to tee. pipe to tee.

H H
17/16" 17/16"
1
/2" 1
/2"
1
/16" P 1" P 1"
1
/16" W
W

B3892 Front View B3895 Front View

Stainless steel facing

plate on tee - filled
Teflon® on base.
B
L

B3892 & B3895 Side View

† Mark shown in this document is the property of its respective owner.

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

148
 Pipe Supports, Guides, Shields & Saddles
Fig. B3891 - B3897 - Pipe Slide Assembly Series (TOLCO Fig. 424 thru Fig. 431)

Shields & Saddles

Supports, Guides,
Field weld
Field weld pipe to tee.
pipe to tee.
H 1
/2"
H 1
/2"
17/16"
17/16"
1
/2"
1
/2" P
1
/16" P 1
/16"
W
W 1" 1"

B3893 Front View B3896 Front View

Stainless steel facing

plate on tee - filled
Teflon® on base.
B
L

B3893 & B3896 Side View

Field weld
pipe to tee.

H
Stainless steel facing
plate on tee - filled
Teflon® on disc. 21/2" 21/2"
B
2 /2"
1
B 2 /2"
1
L
L

B3897 Front View B3897 Side View

† Mark shown in this document is the property of its respective owner.

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

149
 Pipe Supports, Guides, Shields & Saddles
Fig. B3991 - B3993B Material: Tee & H Slides - Steel with Heat Cured PTFE modified coating
Pipe Slide Assembly Series at slide plate.
(TOLCO Fig. 424 thru Fig. 431) Base - Steel with 3/32” (2.4mm) thick Teflon®† slide pads.
Finish: Black paint.
Shields & Saddles
Supports, Guides,

Service: Designed to support pipe where horizontal movement from

expansion and contraction is present.
Approvals: Conforms to Federal Specification WW-H-171E & A-A-1192A and
Manufacturers Standardization Society ANSI/MSS SP-69 & SP-58, Type 35.
Operating Temperature Rating:
400°F (204°C) maximum at base
Loading: Capable of supporting constant loads up to 2000 Psi at 70°F
(21°C)
† Mark shown in this document is the property of its respective owner.

B3993 - 5 - 04 - CL

Base Style Pipe Size Travel Options

3 5 = 1” (25) - 8” (200) 04 = 4” (100) Standard Slide = Blank
3B 10 = 10” (250) - 24” (600) 10 = 10” (250) W/ End Plates = EP - Pipe Size
W/ B3140 Clamps = CL - Pipe Size

T-Slide
B3993-5 B3993B-5 B3991-5

H-Slide

B3993-10 B3993B-10 B3991-10

Options:

CL (standard slide with

EP (standard slide with B3140 clamps)
end plates)

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

150
 Pipe Supports, Guides, Shields & Saddles
Fig. B3991 - B3993B - Pipe Slide Assembly Series (TOLCO Fig. 424 thru Fig. 431)

Shields & Saddles

Supports, Guides,
Pipe Travel Height H Length L Depth B Width C
Size In. (mm) Part No. In. (mm) In. (mm) In. (mm) In. (mm)

B3991-5 47/16" (112.7) 6" (152.4) 3" (76.2) 81/2" (215.9)

B3993-5 47/16" (112.7) 6" (152.4) 3" (76.2) N/A N/A
B3993B-5 411/16" (119.1) 6" (152.4) 3" (76.2) 81/2" (215.9)
4" (101.6)
B3991-10 47/8" (123.8) 6" (152.4) 4" (101.6) 141/2" (368.3)
B3993-10 47/8" (123.8) 6" (152.4) 4" (101.6) N/A N/A
1" to 24" B3993B-10 51/8" (130.2) 6" (152.4) 4" (101.6) 141/2" (368.3)
(25 to 600) B3991-5 47/16" (112.7) 12" (304.8) 3" (76.2) 81/2" (215.9)
B3993-5 47/16" (112.7) 12" (304.8) 3" (76.2) N/A N/A
B3993B-5 411/16" (119.1) 12" (304.8) 3" (76.2) 81/2" (215.9)
10" (254.0)
B3991-10 47/8" (123.8) 12" (304.8) 4" (101.6) 141/2" (368.3)
B3993-10 47/8" (123.8) 12" (304.8) 4" (101.6) N/A N/A
B3993B-10 51/8" (130.2) 12" (304.8) 4" (101.6) 141/2" (368.3)

Max
Pipe Travel Width P Width W Recommended Load
Size In. (mm) Part No. In. (mm) In. (mm) Lbs. (kN)

B3991-5 6" (152.4) N/A N/A 16000 (71.2)

B3993-5 2" (50.8) 41/2" (114.3) 12000 (53.4)
B3993B-5 2" (50.8) 41/2" (114.3) 12000 (53.4)
4" (101.6)
B3991-10 12" (304.8) N/A N/A 32000 (142.3)
B3993-10 6" (152.4) 811/16" (220.7) 24000 (106.8)
1" to 24" B3993B-10 6" (152.4) 811/16" (220.7) 24000 (106.8)
(25 to 600) B3991-5 6" (152.4) N/A N/A 16000 (71.2)
B3993-5 2" (50.8) 41/2" (114.3) 12000 (53.4)
B3993B-5 2" (50.8) 41/2" (114.3) 12000 (53.4)
10" (254.0)
B3991-10 12" (304.8) N/A N/A 32000 (142.3)
B3993-10 6" (152.4) 811/16" (220.7) 24000 (106.8)
B3993B-10 6" (152.4) 811/16" (220.7) 24000 (106.8)

*Based on Teflon® † of 2000 psi.

† Mark shown in this document is the property of its respective owner.

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

151
 Pipe Supports, Guides, Shields & Saddles
Fig. B3991 - Pipe Slide Assembly Series dimensional drawings (TOLCO Fig. 424 thru Fig. 431)
Pipe to be field
welded to
T or H slides.
Shields & Saddles
Supports, Guides,

See charts on page 151

for H, L, B, C, P & W
dimensions
COP ∅
9/16”∅
∅
9/16”∅
(14)
H (14) H
BOP

3/4” P 3/4” 3/4” P 3/4”

(19) (19) (19) C (19)
C

B3991-5 Front View B3991-10 Front View

Pipe Size ‘BOP‘ ‘COP’

In. (mm) In. (mm) In. (mm)
10” (250) 41/8" (104.8) 91/2" (241.3)
12” (300) 41/4" (107.9) 105/8" (269.9)
14” (350) 43/8" (111.1) 113/8" (288.9)

B3991-5 (shown) 16” (400) 43/8" (111.1) 123/8" (314.3)

& B3991-10 18" (450) 43/8" (111.1) 133/8" (339.7)
Side View B 20” (500) 41/2" (114.3) 141/2" (368.3)
L 24” (600) 45/8" (117.5) 165/8" (422.3)

Fig. B3993 Pipe Slide Assembly Series dimensional drawings (TOLCO Fig. 424 thru Fig. 431)
Pipe to be field
welded to
T or H slides.

See charts on page 151

for ‘H’, ‘L’, ‘B’, ‘C’, ‘P’ &
‘W’ dimensions
H COP
H
BOP

P
P
W W

B3993-5 Front View

B3993-10 Front View

Pipe Size BOP COP

In. (mm) In. (mm) In. (mm)
10” (250) 41/8" (104.8) 91/2" (241.3)
12” (300) 41/4" (107.9) 105/8" (269.9)
14” (350) 43/8" (111.1) 113/8" (288.9)
B3993-5 (shown) 16” (400) 43/8" (111.1) 123/8" (314.3)
& B3993-10 18" (450) 43/8" (111.1) 133/8" (339.7)
Side View B 20” (500) 41/2" (114.3) 141/2" (368.3)
L 24” (600) 45/8" (117.5) 165/8" (422.3)

† Mark shown in this document is the property of its respective owner.

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

152
 Pipe Supports, Guides, Shields & Saddles
Fig. B3993B Pipe Slide Assembly Series dimensional drawings (TOLCO Fig. 424 thru Fig. 431)

Pipe to be field
welded to

Shields & Saddles

Supports, Guides,
T or H slides.

See charts on page 151

for H, L, B, C, P & W
dimensions
COP
H
H
∅
9/16”∅ BOP
∅
9/16”∅
(14) (14)
3/4” P 3/4” 3/4” P 3/4”
(19) W (19)
W
(19) (19)
C C

B3993B-5 Front View B3993B-10 Front View

Pipe Size BOP COP

In. (mm) In. (mm) In. (mm)
10” (250) 43/8" (111.1) 93/4" (247.6)
12” (300) 41/2" (114.3) 107/8" (276.2)
14” (350) 45/8" (117.5) 115/8" (295.3)

B3993B-5 (shown) 16” (400) 45/8" (117.5) 125/8" (320.7)

& B3993B-10 18" (450) 45/8" (117.5) 135/8" (346.1)
Side View B 20” (500) 43/4" (120.6) 143/4" (374.6)
L 24” (600) 47/8" (123.8) 167/8" (428.6)

† Mark shown in this document is the property of its respective owner.

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

153
 Pipe Supports, Guides, Shields & Saddles
Fig. B3160 thru B3165 - Pipe Covering Protection Saddle (TOLCO Fig. 260 thru Fig. 265)
Material: Steel; Stainless Steel available
Standard Finish: Plain or Electro-Galvanized
Shields & Saddles
Supports, Guides,

Service: Designed to protect pipe insulation

on high temperature pipe lines. Saddles are
12" (304.8mm) long. Center rib is furnished on all
saddle sizes 12" (300mm) and above.
Order By: Figure number and finish. Select part 12"
(304.8)
number by insulation thickness and add nominal pipe
size (Ex: B3161-11/4 PLN).
Approvals: Complies with Federal Specification Sizes 3/4" (20mm) thru 10" (250mm)
WW-H-171E & A-A-1192A Type 40A and Type 40B
and Manufacturers Standardization Society ANSI/MSS
SP-69 & SP-58 Type 39A and Type 39B.
Insulation Part
Thickness Number
12"
1" (25.4mm) B3160 (304.8)
11/2" (38.1mm) B3161
2" (50.8mm) B3162
21/2" (63.5mm) B3163 Sizes 12" (300mm) and larger
3" (76.2mm) B3164
4" (101.6mm) B3165

Size For Roller Part Number

B3117SL
B3114 B3118SL
B3120 B3119SL
Pipe Size B3122 B3124 Design Load Approx. Wt./100
Part No. in. (mm) B3122A B3126 B3110 Lbs. (kN) Lbs. (kg)

B3160-3/4 2 2-31/2 21/2 1200 (5.34) 122 (55.3)

B3161-3/4 3/4" (20) 3 2-31/2 31/2 1200 (5.34) 228 (103.4)
B3162-3/4 4 2-31/2 5 1200 (5.34) 297 (134.7)
B3160-1 21/2 2-31/2 3 1200 (5.34) 156 (70.7)
B3161-1 1" (25) 3 2-31/2 4 1200 (5.34) 228 (103.4)
B3162-1 4 2-31/2 5 1200 (5.34) 297 (134.7)
B3160-11/4 21/2 2-31/2 3 1200 (5.34) 156 (70.7)
B3161-11/4 31/2 2-31/2 5 1200 (5.34) 228 (103.4)
11/4" (32)
B3162-11/4 4 2-31/2 5 1200 (5.34) 297 (134.7)
B3163-11/4 5 4-6 6 1200 (5.34) 342 (155.1)
B3160-11/2 3 2-31/2 31/2 1200 (5.34) 172 (78.0)
B3161-11/2 31/2 2-31/2 5 1200 (5.34) 239 (108.4)
11/2" (40)
B3162-11/2 5 4-6 6 1800 (8.00) 311 (141.0)
B3163-11/2 6 4-6 8 1800 (8.00) 417 (189.1)
B3160-2 31/2 2-31/2 4 1200 (5.34) 172 (78.0)
B3161-2 4 2-31/2 5 1200 (5.34) 239 (108.4)
B3162-2 2" (50) 5 4-6 6 1800 (8.00) 311 (141.0)
B3163-2 6 4-6 8 1800 (8.00) 417 (189.1)
B3164-2 8 4-6 8 1800 (8.00) 441 (200.0)
B3160-21/2 31/2 2-31/2 5 1200 (5.34) 210 (95.2)
B3161-21/2 5 4-6 6 1200 (5.34) 268 (121.5)
B3162-21/2 21/2" (65) 6 4-6 8 1800 (8.00) 358 (162.4)
B3163-21/2 8 4-6 8 1800 (8.00) 417 (189.1)
B3164-21/2 8 4-6 10 1800 (8.00) 459 (208.2)

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

154
 Pipe Supports, Guides, Shields & Saddles
Fig. B3160 thru B3165 - Pipe Covering Protection Saddle (TOLCO Fig. 260 thru Fig. 265) (Continued)

Shields & Saddles

Supports, Guides,
12"
(304.8)
12"
(304.8)

Sizes 12" (300mm) and larger

Sizes 3/4" (20mm) thru 10" (250mm)
Insulation Part
Thickness Number
1" (25.4mm) B3160
11/2" (38.1mm) B3161
C A C B 2" (50.8mm) B3162
21/2" (63.5mm) B3163
3" (76.2mm) B3164
4" (101.6mm) B3165

Centerline of Pipe to Centerline of Roll

A B A
Centerline of Thickness
B3117SL, B3118SL, Pipe to Outside of Covering
B3114, B3120, B3119SL, B3124, of Saddle
Pipe Size B3122, B3122A B3126 B3110 C (Per ASTM C 585)
Part No. In. (mm) In. (mm) In. (mm) In. (mm) In. (mm) In. (mm)
B3160-3/4 2" (50.8) 21/4" (57.1) 2" (50.8) 19/16" (39.7) 7/8" (22.2)
B3161-3/4 3/4" (20) 27/16" (61.9) 27/8" (73.0) 23/8" (69.8) 23/16" (55.6) 11/2" (38.1)
B3162-3/4 35/16" (84.1) 37/16" (87.3) 33/8" (85.7) 23/4" (69.8) 115/16" (49.2)
B3160-1 25/16" (58.7) 21/2" (63.5) 25/16" (58.7) 113/16" (46.0) 11/16" (27.0)
B3161-1 1" (25) 27/8" (73.0) 3" (76.2) 27/8" (73.0) 25/16" (58.7) 19/16" (39.7)
B3160-1 37/16" (87.3) 35/8" (92.1) 31/2" (88.9) 27/8" (73.0) 21/8" (54.0)
B3162-11/4 29/16" (65.1) 211/16" (68.3) 21/2" (63.5) 2" (50.8) 15/16" (23.8)
B3161-11/4 31/8" (79.4) 31/4" (82.5) 31/8" (79.4) 29/16" (65.1) 17/16" (36.5)
11/4" (32)
B3162-11/4 311/16" (93.7) 313/16" (96.8) 37/16" (87.3) 31/16" (77.8) 21/8" (54.0)
B3163-11/4 41/16" (103.2) 41/8" (104.8) 41/16" (103.2) 37/16" (87.3) 27/16" (61.9)
B3160-11/2 211/16" (68.3) 27/8" (73.0) 27/16" (61.9) 21/8" (54.0) 11/32" (26.2)
B3161-11/2 33/16" (81.0) 35/16" (84.1) 33/16" (81.0) 29/16" (65.1) 117/32" (38.9)
11/2" (40)
B3162-11/2 39/16" (90.5) 313/16" (96.8) 313/16" (96.8) 31/8" (79.4) 2" (50.8)
B3163-11/2 47/16" (112.7) 43/8" (111.1) 41/2" (114.3) 35/8" (92.1) 227/32" (72.2)
B3160-2 215/16" (74.6) 31/8" (79.4) 215/16" (74.6) 23/8" (60.3) 11/16" (27.0)
B3161-2 37/16" (87.3) 35/8" (92.1) 31/2" (88.9) 27/8" (73.0) 119/32" (40.5)
B3162-2 2" (50) 41/8" (104.8) 41/8" (104.8) 41/16" (103.2) 37/16" (87.3) 21/8" (54.0)
B3163-2 411/16" (119.1) 411/16" (119.1) 43/4" (120.6) 315/16" (100.0) 25/8" (66.7)
B3164-2 51/4" (133.3) 53/16" (131.8) 51/4" (133.3) 41/2" (114.3) 31/8" (79.4)
B3160-21/2 31/4" (82.5) 33/8" (85.7) 31/4" (82.5) 25/8" (66.7) 11/16" (27.0)
B3161-21/2 37/8" (98.4) 315/16" (100.0) 37/8" (98.4) 31/4" (82.5) 17/8" (47.6)
B3162-21/2 21/2" (65) 49/16" (115.9) 49/16" (115.9) 45/8" (117.5) 37/8" (98.4)) 25/16" (58.7)
B3163-21/2 51/8" (130.2) 5" (127.0) 51/8" (130.2) 41/4" (107.9) 27/8" (73.0)
B3164-21/2 57/16" (138.1) 55/16" (134.9) 51/2" (139.7) 49/16" (115.9) 31/16" (77.8)

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

155
 Pipe Supports, Guides, Shields & Saddles
Fig. B3160 thru B3165 - Pipe Covering Protection Saddle (TOLCO Fig. 260 thru Fig. 265) (Continued)
Insulation Part Insulation Part
Thickness Number Thickness Number
1" (25.4mm) B3160 21/2" (63.5mm) B3163
11/2" (38.1mm) B3161 3" (76.2mm) B3164
Shields & Saddles
Supports, Guides,

2" (50.8mm) B3162 4" (101.6mm) B3165

Size For Roller Part Number

B3117SL
B3114 B3118SL
B3120 B3119SL
Pipe Size B3122 B3124 Design Load Approx. Wt./100
Part No. In. (mm) B3122A B3126 B3110 Lbs. (kN) Lbs. (kg)

B3160-3 4 2-31/2 5 1800 (8.00) 210 (95.2)

B3161-3 5 4-6 6 1800 (8.00) 268 (166.9)
B3162-3 3" (80) 6 4-6 8 1800 (8.00) 358 (162.4)
B3163-3 8 4-6 8 1800 (8.00) 417 (189.1)
B3164-3 8 8-10 10 1800 (8.00) 459 (208.2)
B3160-31/2 5 4-6 6 1200 (5.34) 226 (102.5)
B3161-31/2 6 4-6 8 1800 (8.00) 289 (131.1)
B3162-31/2 31/2" (90) 8 4-6 8 1800 (8.00) 364 (165.1)
B3163-31/2 8 8-10 10 1800 (8.00) 422 (191.4)
B3164-31/2 10 8-10 10 1800 (8.00) 488 (221.3)
B3160-4 5 4-6 6 1800 (8.00) 226 (102.5)
B3161-4 6 4-6 8 1800 (8.00) 289 (131.1)
B3162-4 8 8-10 8 1800 (8.00) 364 (165.1)
4" (100)
B3163-4 8 8-10 10 1800 (8.00) 422 (191.4)
B3164-4 10 8-10 10 1800 (8.00) 488 (221.3)
B3165-4 10 8-10 12 1800 (8.00) 616 (279.4)
B3160-5 6 4-6 8 1800 (8.00) 250 (113.4)
B3161-5 8 4-6 8 1800 (8.00) 289 (131.1)
B3162-5 8 8-10 10 1800 (8.00) 364 (165.1)
5" (125)
B3163-5 10 8-10 10 1800 (8.00) 422 (191.4)
B3164-5 10 8-10 12 1800 (8.00) 488 (221.3)
B3165-5 12 8-10 14 1800 (8.00) 643 (291.6)
B3160-6 8 8-10 8 1800 (8.00) 387 (175.5)
B3161-6 8 8-10 10 1800 (8.00) 498 (225.9)
B3162-6 10 8-10 10 1800 (8.00) 594 (269.4)
6" (150)
B3163-6 10 8-10 12 1800 (8.00) 694 (314.8)
B3164-6 12 8-10 12 1800 (8.00) 794 (360.1)
B3165-6 14 12-14 16 1800 (8.00) 1009 (457.7)
B3160-8 10 8-10 12 1800 (8.00) 478 (216.8)
B3161-8 10 8-10 12 1800 (8.00) 554 (251.3)
B3162-8 10 8-10 12 1800 (8.00) 674 (305.7)
8" (200)
B3163-8 12 8-10 14 1800 (8.00) 782 (354.7)
B3164-8 14 12-14 16 1800 (8.00) 893 (405.0)
B3165-8 16 12-14 18 1800 (8.00) 1089 (494.0)
B3160-10 12 12-14 14 1800 (8.00) 546 (247.6)
B3161-10 12 12-14 14 1800 (8.00) 642 (291.2)
B3162-10 14 16-20 16 1800 (8.00) 750 (340.2)
10" (250)
B3163-10 14 16-20 16 1800 (8.00) 850 (385.5)
B3164-10 16 16-20 18 1800 (8.00) 957 (434.1)
B3165-10 18 16-20 20 1800 (8.00) 1137 (515.7)

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

156
 Pipe Supports, Guides, Shields & Saddles
Fig. B3160 thru B3165 - Pipe Covering Protection Saddle (Continued)
Insulation Part Insulation Part
Thickness Number Thickness Number
1" (25.4mm) B3160 21/2" (63.5mm) B3163 C A C B
11/2" (38.1mm) B3161 3" (76.2mm) B3164

Shields & Saddles

Supports, Guides,
2" (50.8mm) B3162 4" (101.6mm) B3165

Centerline of Pipe to Centerline of Roll

A B A
Centerline of Thickness
B3114 B3117ST, B3118SL, Pipe to Outside of Covering
B3114, B3120, B3119SL, B3124, of Saddle
Pipe Size B3122, B3122A B3126 B3110 C (Per ASTM C 585)
Part No. In. (mm) In. (mm) In. (mm) In. (mm) In. (mm) In. (mm)

B3160-3 33/8" (85.7) 31/2" (88.9) 35/8" (91.1) 3" (76.2) 11/32" (26.2)
B3161-3 41/4" (107.9) 45/16" (109.5) 41/4" (107.9) 39/16" (90.5) 19/16" (39.7)
B3162-3 3" (80) 415/16" (125.4) 415/16" (125.4) 415/16" (125.4) 43/16" (106.4) 21/16" (52.4)
B3163-3 57/16" (138.1) 53/8" (136.5) 57/16" (138.1) 45/8" (117.5) 29/16" (65.1)
B3164-3 513/16" (147.6) 6" (152.4) 57/8" (149.2) 415/16" (125.4) 31/16" (77.8)
B3160-31/2 313/16" (96.8) 37/8" (98.4) 313/16" (96.8) 33/16" (81.0) 11/32" (26.2)
B3161-31/2 43/8" (111.1) 43/8" (111.1) 43/8" (111.1) 311/16" (93.7) 19/16" (39.7)
B3162-31/2 31/2" (90) 5" (127.0) 5" (127.0) 5" (127.0) 41/4" (107.9) 21/16" (52.4)
B3163-31/2 51/2" (139.7) 511/16" (144.5) 59/16" (141.3) 45/8" (117.5) 225/32" (70.6)
B3164-31/2 63/16" (157.2) 65/16" (160.3) 63/16" (157.2) 51/4" (133.3) 31/16" (77.8)
B3160-4 41/8" (104.8) 41/8" (104.8) 41/8" (104.8) 37/16" (87.3) 11/16" (27.0)
B3161-4 411/16" (119.1) 47/16" (112.7) 43/4" (120.6) 4" (101.6) 19/16" (39.7)
B3162-4 55/16" (134.9) 51/4" (133.3) 55/16" (134.9) 41/2" (114.3) 21/16" (52.4)
4" (100)
B3163-4 513/16" (147.6) 6" (152.4) 57/8" (149.2) 415/16" (125.4) 29/16" (65.1)
B3164-4 67/16" (163.5) 69/16" (166.7) 67/16" (163.5) 51/2" (139.7) 31/8" (79.4)
B3165-4 79/16" (192.1) 75/8" (193.7) 79/16" (192.1) 61/2" (165.1) 41/8" (104.8)
B3160-5 411/16" (119.1) 411/16" (119.1) 43/4" (120.6) 315/16" (100.0) 11/32" (26.2)
B3161-5 55/16" (134.9) 51/4" (133.3) 55/16" (134.9) 49/16" (115.9) 117/32" (38.9)
B3162-5 57/8" (149.2) 61/8" (155.6) 6" (152.4) 51/8" (130.2) 21/32" (51.6)
5" (125)
B3163-5 67/16" (163.5) 69/16" (166.7) 67/16" (163.5) 59/16" (141.3) 29/16" (65.1)
B3164-5 7" (177.8) 73/16" (182.6) 71/8" (181.0) 61/8" (155.6) 33/32" (78.6)
B3165-5 83/16" (208.0) 83/16" (208.0) 83/8" (212.7) 71/16" (179.4) 45/32" (105.5)
B3160-6 51/4" (133.3) 51/4" (133.3) 51/4" (133.3) 41/2" (114.3) 1" (25.4)
B3161-6 57/8" (149.2) 61/16" (154.0) 515/16" (150.8) 5" (127.0) 11/2" (38.1)
B3162-6 61/2" (165.1) 65/8" (168.3) 61/2" (165.1) 59/16" (141.3) 21/16" (52.4)
6" (150)
B3163-6 71/16" (179.4) 71/8" (181.0) 71/8" (181.0) 61/16" (154.0) 29/16" (65.1)
B3164-6 75/8" (193.7) 711/16" (195.3) 75/8" (193.7) 69/16" (166.7) 31/16" (77.8)
B3165-6 91/16" (230.2) 815/16" (227.0) 9" (228.6) 73/4" (196.8) 43/16" (106.4)
B3160-8 61/2" (165.1) 65/8" (168.3) 69/16" (166.7) 59/16" (141.3) 11/32" (26.2)
B3161-8 71/16" (179.4) 71/8" (181.0) 71/16" (179.4) 61/16" (154.0) 19/16" (39.7)
B3162-8 79/16" (192.1) 75/8" (193.7) 75/8" (193.7) 69/16" (166.7) 21/16" (52.4)
8" (200)
B3163-8 85/16" (211.1) 85/16" (211.1) 81/2" (215.9) 73/16" (182.6) 211/16" (68.3)
B3164-8 91/16" (230.2) 815/16" (227.0) 9" (228.6) 73/4" (196.8) 33/16" (81.0)
B3165-8 10" (254.0) 915/16" (252.4) 101/16" (255.6) 811/16" (220.7) 43/16" (106.4)
B3160-10 711/16" (195.3) 73/4" (196.8) 77/8" (200.0) 65/8" (168.3) 31/32" (24.6)
B3161-10 85/16" (211.1) 85/16" (211.1) 87/16" (214.3) 73/16" (182.6) 15/8" (41.3)
B3162-10 9" (228.6) 87/8" (225.4) 87/8" (225.4) 711/16" (195.3) 21/8" (54.0)
10" (250)
B3163-10 5
9 /8" (244.5) 97/16" (239.7) 91/2" (241.3) 83/16" (208.0) 25/8" (66.7)
B3164-10 101/8" (257.2) 103/16" (258.8) 103/16" (258.8) 83/4" (222.2) 31/8" (79.4)
B3165-10 111/4" (285.7) 113/16" (284.2) 111/4" (285.7) 93/4" (247.6) 41/8" (104.8)

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

157
 Pipe Supports, Guides, Shields & Saddles
Fig. B3160 thru B3165 - Pipe Covering Protection Saddle (TOLCO Fig. 260 thru Fig. 265) (Continued)
Insulation Part Insulation Part
Thickness Number Thickness Number
1" (25.4mm) B3160 21/2" (63.5mm) B3163
11/2" (38.1mm) B3161 3" (76.2mm) B3164
Shields & Saddles
Supports, Guides,

2" (50.8mm) B3162 4" (101.6mm) B3165

Size For Roller Part Number

B3114 B3117SL
B3114 B3118SL
Pipe Size B3120, B3122 B3119SL Design Load Approx. Wt./100
Part No. In. (mm) B3122A B3124, B3126 B3110 Lbs. (kN) Lbs. (kg)

B3160-12 14 12-14 16 5000 (22.24) 688 (312.1)

B3161-12 14 12-14 16 5000 (22.24) 836 (379.2)
B3162-12 16 16-20 18 5000 (22.24) 963 (436.8)
12" (300)
B3163-12 16 16-20 18 5000 (22.24) 1091 (494.9)
B3164-12 18 16-20 20 5000 (22.24) 1218 (552.5)
B3165-12 20 16-20 24 5000 (22.24) 1462 (663.1)
B3161-14 16 16-20 18 5000 (22.24) 828 (375.6)
B3162-14 16 16-20 18 5000 (22.24) 963 (436.8)
B3163-14 14" (350) 18 16-20 20 5000 (22.24) 1099 (498.5)
B3164-14 18 16-20 20 5000 (22.24) 1230 (557.9)
B3165-14 20 24 24 5000 (22.24) 1486 (674.0)
B3161-16 18 16-20 20 5000 (22.24) 907 (411.4)
B3162-16 18 16-20 20 5000 (22.24) 1039 (471.3)
B3163-16 16" (400) 20 16-20 24 7200 (32.02) 1163 (527.5)
B3164-16 20 24 24 7200 (32.02) 1298 (588.8)
B3165-16 24 24 24 7200 (32.02) 1554 (704.9)
B3161-18 20 16-20 24 5000 (22.24) 979 (444.1)
B3162-18 20 24 24 7200 (32.02) 1107 (502.1)
B3163-18 18" (450) 24 24 24 7200 (32.02) 1230 (557.9)
B3164-18 24 24 24 7200 (32.02) 1362 (617.8)
B3165-18 24 24 - 7200 (32.02) 1617 (733.5)
B3161-20 24 24 24 7200 (32.02) 1043 (473.1)
B3162-20 24 24 24 7200 (32.02) 1171 (531.1)
B3163-20 20" (500) 24 24 - 7200 (32.02) 1294 (586.9)
B3164-20 24 24 - 7200 (32.02) 1430 (648.6)
B3165-20 30 30 - 7200 (32.02) 1689 (766.1)
B3161-24 30 30 - 7200 (32.02) 1179 (534.8)
B3162-24 30 30 - 7200 (32.02) 1306 (592.4)
B3163-24 24" (600) 30 30 - 7200 (32.02) 1442 (654.1)
B3164-24 30 30 - 7200 (32.02) 1562 (708.5)
B3165-24 30 30 - 7200 (32.02) 1821 (826.0)
B3161-30 - 36-42 - 7200 (32.02) 1370 (621.4)
B3162-30 - 36-42 - 7200 (32.02) 1502 (681.3)
B3163-30 30" (750) - 36-42 - 7200 (32.02) 1640 (743.9)
B3164-30 - 36-42 - 7200 (32.02) 1761 (798.8)
B3165-30 - 36-42 - 7200 (32.02) 2008 (910.8)
B3161-36 - 36-42 - 7200 (32.02) 1574 (713.9)
B3162-36 - 36-42 - 7200 (32.02) 1701 (771.6)
B3163-36 36" (900) - 36-42 - 7200 (32.02) 1857 (842.3)
B3164-36 - 36-42 - 7200 (32.02) 1961 (889.5)
B3165-36 - 36-42 - 7200 (32.02) 2216 (1005.2)

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

158
 Pipe Supports, Guides, Shields & Saddles
Fig. B3160 thru B3165 - Pipe Covering Protection Saddle (Continued)
Insulation Part Insulation Part
Thickness Number Thickness Number
1" (25.4mm) B3160 21/2" (63.5mm) B3163 C A C B
11/2" (38.1mm) B3161 3" (76.2mm) B3164

Shields & Saddles

Supports, Guides,
2" (50.8mm) B3162 4" (101.6mm) B3165

Centerline of Pipe to Centerline of Roll

A B A Centerline of Thickness
B3117SL, B3118SL Pipe to Outside of Covering
Nominal B3114, B3120 B3119SL of Saddle (Per
Part No. Pipe Size B3122, B3122A B3124, B3126 B3110 C ASTM C 585)
In. (mm) In. (mm) In. (mm) In. (mm) In. (mm) In. (mm)

B3160-12 815/16" (227.0) 813/16" (223.8) 87/8" (225.4) 75/8" (193.7) 11/16" (27.0)
B3161-12 99/16" (242.9) 97/16" (239.7) 91/2" (241.3) 83/16" (208.0) 15/8" (41.3)
B3162-12 12" (300) 101/16" (255.6) 101/8" (257.2) 101/8" (257.2) 83/4" (222.2) 21/8" (54.0)
B3163-12 105/8" (269.9) 105/8" (269.9) 105/8" (269.9) 91/4" (234.9) 25/8" (66.7)
B3164-12 113/16" (284.2) 113/16" (284.2) 111/4" (285.7) 911/16" (246.1) 31/8" (79.4)
B3165-12 125/16" (312.7) 123/16" (309.6) 125/16" (312.7) 103/4" (273.0) 41/8" (104.8)
B3161-14 101/16" (255.6) 915/16" (252.4) 101/16" (255.6) 811/16" (220.7) 11/2" (38.1)
B3162-14 105/8" (269.9) 105/8" (269.9) 105/8" (269.9) 93/16" (233.4) 2" (50.8)
B3163-14 14" (350) 113/16" (284.2) 113/16" (284.2) 111/4" (285.7) 93/4" (247.6) 21/2" (63.5)
B3164-14 113/4" (298.4) 1111/16" (296.9) 113/4" (298.4) 101/4" (260.3) 3" (76.2)
B3165-14 127/8" (327.0) 127/16" (315.9) 127/8" (327.0) 113/16" (284.2) 4" (101.6)
B3161-16 111/8" (282.6) 111/8" (282.6) 113/16" (284.2) 911/16" (246.1) 11/2" (38.1)
B3162-16 1113/16" (300.0) 1111/16" (296.9) 113/4" (298.4) 1014" (260.3) 2" (50.8)
B3163-16 16" (400) 125/16" (312.7) 121/8" (308.0) 125/16" (312.7) 1011/16" (271.5) 21/2" (63.5)
B3164-16 127/8" (327.0) 129/16" (319.1) 127/8" (327.0) 111/4" (285.7) 3" (76.2)
B3165-16 1315/16" (354.0) 139/16" (344.5) 1315/16" (354.0) 121/4" (311.1) 4" (101.6)
B3161-18 121/4" (311.1) 121/8" (308.0) 121/4" (311.1) 1011/16" (271.5) 11/2" (38.1)
B3162-18 127/8" (327.0) 121/2" (317.5) 127/8" (327.0) 111/4" (285.7) 2" (50.8)
B3163-18 18" (450) 133/8" (339.7) 13" (330.2) 133/8" (339.7) 1111/16" (296.9) 21/2" (63.5)
B3164-18 1315/16" (354.0) 139/16" (344.5) 1315/16" (354.0) 121/4" (311.1) 3" (76.2)
B3165-18 15" (381.0) 149/16" (369.9) -- -- 131/4" (336.5) 4" (101.6)
B3161-20 133/8" (339.7) 13" (330.2) 133/8" (339.7) 1111/16" (296.9) 11/2" (38.1)
B3162-20 1315/16" (354.0) 131/2" (342.9) 1315/16" (354.0) 123/16" (309.6) 2" (50.8)
B3163-20 20" (500) 147/16" (366.7) 14" (355.6) -- -- 1211/16" (322.3) 21/2" (63.5)
B3164-20 1415/16" (379.4) 149/16" (369.9) -- -- 133/16" (350.8) 3" (76.2)
B3165-20 161/4" (412.7) 157/8" (403.2) -- -- 141/4" (361.9) 4" (101.6)
B3161-24 1511/16" (398.5) 155/16" (388.9) -- -- 1311/16" (347.7) 11/2" (38.1)
B3162-24 161/4" (412.8) 157/8" (403.2) -- -- 143/16" (360.4) 2" (50.8)
B3163-24 24" (600) 163/4" (425.4) 165/16" (414.3) -- -- 145/8" (377.8) 21/2" (63.5)
B3164-24 173/8" (441.3) 167/8" (428.6) -- -- 151/4" (387.3) 3" (76.2)
B3165-24 187/16" (468.3) 1715/16" (455.6) -- -- 161/4" (412.7) 4" (101.6)
B3161-30 -- -- 187/8" (479.4) -- -- 1611/16" (423.9) 11/2" (38.1)
B3162-30 -- -- 193/8" (492.1) -- -- 173/16" (436.6) 2" (50.8)
B3163-30 30" (750) -- -- 1915/16" (506.4) -- -- 1711/16" (449.3) 21/2" (63.5)
B3164-30 -- -- 201/2" (520.7) -- -- 183/16" (462.0) 3" (76.2)
B3165-30 -- -- 211/2" (546.1) -- -- 193/16" (487.4) 4" (101.6)
B3161-36 -- -- 221/8" (562.0) -- -- 1911/16" (500.1) 11/2" (38.1)
B3162-36 -- -- 225/8" (574.7) -- -- 203/16" (512.8) 2" (50.8)
B3163-36 36" (900) -- -- 233/16" (589.0) -- -- 2011/16" (525.5) 21/2" (63.5)
B3164-36 -- -- 2311/16" (601.7) -- -- 213/16" (538.2) 3" (76.2)
B3165-36 -- -- 2411/16" (627.1) -- -- 223/16" (563.6) 4" (101.6)

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

159
 Pipe Supports, Guides, Shields & Saddles
Selection Tables for:
Insulation Protection Shields Fig. B3151 Insulation Protection Shield (Page 161)
(TOLCO Fig. 219 & Fig. 220) Fig. B3153 Insulation Protection Shield with 'Loc' Tabs (Page 161)
Fig. B3154 Short Insulation Protection Shield (Page 162)
Shield Size Selection Table Fig. B3155 Short Insulation Protection Shield with 'Loc' Tabs (Page 162)
Shields & Saddles
Supports, Guides,

Nominal Pipe Insulation Thickness

1 3
or Tubing Size /2" (12.7mm) /4" (19.0mm) 1" (25.4mm) 11/2" (38.1mm) 2" (50.8mm) 21/2" (63.5mm) 3" (76.2mm) 4" (101.6mm)
1/2" (15) 1X 2X 3X 5X 7X -- -- --
3/4" (20) 2X 3X 3X 5X 7X -- -- --
1" (25) 2X 3X 4X 6X 8X -- -- --
11/4" (32) 3X 4X 4X 7X 8X -- -- --
11/2" (40) 3X 4X 5X 7X 9X -- -- --
2" (50) 4X 5X 6X 8X 9X 10X* 11X* --
21/2" (65) 5X 6X 7X 9X 10X* 11X* 11X* 13Y*
3" (80) 6X 7X 8X 9X 10X* 11X* 12Y* 14Z
31/2" (90) 7X 8X 9X 10X* 11X* 12Y* 13Y* 15Z
4" (100) 8X 9X 9X 10X* 11X* 12Y* 13Y* 15Z
5" (125) -- -- 10Y* 11Y* 12Y* 13Y* 14Z 16Z
6" (150) -- -- 11Y* 12Y* 13Y* 14Z 15Z 17Z
8" (200) -- -- 13Y* 14Z 15Z 16Z 17Z 19Z
10" (250) -- -- 15Z 16Z 17Z 18Z 19Z 21Z
12" (300) -- -- 17Z 18Z 19Z 20Z 21Z 23Z
14" (350) -- -- 18Z 19Z 20Z 21Z 22Z 24Z
16" (400) -- -- 20Z 21Z 22Z 23Z 24Z 26Z
18" (450) -- -- 22Z 23Z 24Z 25Z 26Z 28Z
20" (500) -- -- 24Z 25Z 26Z 27Z 28Z 30Z
24" (600) -- -- 28Z 29Z 30Z 31Z 32Z 33Z
*When selecting B3154 or B3155, replace 'X' or 'Y' designation with 'Z'.

Pipe Hanger Size Selection Table

Nominal Pipe Insulation Thickness
1 3
or Tubing Size /2" (12.7mm) /4" (19.0mm) 1" (25.4mm) 11/2" (38.1mm) 2" (50.8mm) 21/2" (63.5mm) 3" (76.2mm) 4" (101.6mm)
1/2" (15) 11/2 2 21/2 31/2 5 -- -- --
3/4" (20) 2 21/2 21/2 31/2 5 -- -- --
1" (25) 2 21/2 3 4 5 -- -- --
11/4" (32) 21/2 3 3 5 5 -- -- --
11/2" (40) 21/2 3 31/2 5 6 -- -- --
2" (50) 3 31/2 4 5 6 8 8 --
21/2" (65) 31/2 4 5 6 8 8 10 10
3" (80) 4 5 5 6 8 8 10 12
31/2" (90) 5 5 6 8 8 10 10 12
4" (100) 5 6 6 8 8 10 10 12
5" (125) -- -- 8 8 10 10 12 14
6" (150) -- -- 8 10 10 12 12 16
8" (200) -- -- 10 12 12 14 16 18
10" (250) -- -- 12 14 16 16 18 20
12" (300) -- -- 14 16 18 18 20 22
14" (350) -- -- 16 18 18 20 20 22
16" (400) -- -- 18 20 20 22 22 24
18" (450) -- -- 20 22 22 24 24 26
20" (500) -- -- 22 24 24 26 26 28
24" (600) -- -- 26 28 28 30 30 32
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

160
 Pipe Supports, Guides, Shields & Saddles
Fig. B3151 - Insulation Protection Shield (TOLCO Fig. 220)
Fig. B3153 - Insulation Protection Shield with "Loc" Tabs (TOLCO Fig. 219)
Material: Steel (Stainless steel available)
Function: Designed to protect pipe insulation when used

Shields & Saddles

Supports, Guides,
Stock Size
with hangers.
Approvals: Complies with Federal Specification L
Shield I.D. L
WW-H-171E & A-A-1192A Type 41 and Manufacturers (Inside Dia.)
Standardization Society ANSI/MSS SP-69 & SP-58 Type 40.
Finish: Pre-Galvanized B3151
Order By: Figure number and finish.
Note: See Selection Tables on page 160 for proper
Shield I.D.
sizing. Stock Size
(Inside Dia.)

B3153
B3153 same dimension as B3151, but with bottom tabs for centering
and securing the shield to hanger.

Part Part Stock Size L Shield 'I.D.' Approx. Wt./100 Pipe Hanger Size
No. No. in. (mm) in. (mm) in. (mm) Lbs. (kg) in. (mm)

B3151-1X B3153-1X 18 Ga. (1.2) 12" (304.8) 1.90 (48.2) 50 (22.7) 11/2" (40)
B3151-2X B3153-2X 18 Ga. (1.2) 12" (304.8) 2.38 (60.4) 62 (28.1) 2" (50)
B3151-3X B3153-3X 18 Ga. (1.2) 12" (304.8) 2.88 (73.1) 75 (34.0) 21/2" (65)
B3151-4X B3153-4X 18 Ga. (1.2) 12" (304.8) 3.50 (88.9) 92 (41.7) 3" (80)
B3151-5X B3153-5X 18 Ga. (1.2) 12" (304.8) 4.00 (101.6) 104 (47.2) 31/2" (90)
B3151-6X B3153-6X 18 Ga. (1.2) 12" (304.8) 4.50 (114.3) 118 (53.5) 4" (100)
B3151-7X B3153-7X 18 Ga. (1.2) 12" (304.8) 5.00 (127.0) 129 (58.5) 5" (125)
B3151-8X B3153-8X 18 Ga. (1.2) 12" (304.8) 5.56 (141.2) 147 (66.7) 5" (125)
B3151-9X B3153-9X 16 Ga. (1.5) 12" (304.8) 6.64 (168.6) 219 (99.3) 6" (150)
B3151-10X B3153-10X 16 Ga. (1.5) 12" (304.8) 7.64 (194.0) 253 (114.7) 8" (200)
B3151-11X B3153-11X 16 Ga. (1.5) 12" (304.8) 8.64 (219.4) 286 (129.7) 8" (200)
B3151-10Y -- 16 Ga. (1.5) 18" (457.2) 7.64 (194.0) 377 (171.0) 8" (200)
B3151-11Y -- 16 Ga. (1.5) 18" (457.2) 8.64 (219.4) 424 (192.3) 8" (200)
B3151-12Y -- 16 Ga. (1.5) 18" (457.2) 9.64 (244.8) 475 (215.4) 10" (250)
B3151-13Y -- 16 Ga. (1.5) 18" (457.2) 10.76 (273.3) 529 (239.9) 10" (250)
B3151-14Z -- 14 Ga. (1.9) 24" (609.6) 11.76 (298.7) 964 (437.3) 12" (300)
B3151-15Z -- 14 Ga. (1.9) 24" (609.6) 12.76 (324.1) 1045 (474.0) 12" (300)
B3151-16Z -- 14 Ga. (1.9) 24" (609.6) 14.00 (355.6) 1146 (519.8) 14" (350)
B3151-17Z -- 14 Ga. (1.9) 24" (609.6) 15.00 (381.0) 1227 (556.5) 16" (400)
B3151-18Z -- 14 Ga. (1.9) 24" (609.6) 16.00 (406.4) 1308 (593.3) 16" (400)
B3151-19Z -- 14 Ga. (1.9) 24" (609.6) 17.00 (431.8) 1393 (631.8) 18" (450)
B3151-20Z -- 12 Ga. (2.6) 24" (609.6) 18.00 (457.2) 2064 (936.2) 18" (450)
B3151-21Z -- 12 Ga. (2.6) 24" (609.6) 19.00 (482.6) 2178 (987.9) 20" (500)
B3151-22Z -- 12 Ga. (2.6) 24" (609.6) 20.00 (508.0) 2292 (1039.6) 20" (500)
B3151-23Z -- 12 Ga. (2.6) 24" (609.6) 21.00 (533.4) 2406 (1091.3) 24" (600)
B3151-24Z -- 12 Ga. (2.6) 24" (609.6) 22.00 (558.8) 2520 (1143.1) 24" (600)
B3151-25Z -- 12 Ga. (2.6) 24" (609.6) 23.00 (584.2) 2634 (1194.8) 24" (600)
B3151-26Z -- 12 Ga. (2.6) 24" (609.6) 24.00 (609.6) 2753 (1248.7) 24" (600)
B3151-27Z -- 12 Ga. (2.6) 24" (609.6) 25.00 (635.0) 2862 (1298.2) 30" (750)
B3151-28Z -- 12 Ga. (2.6) 24" (609.6) 26.00 (660.4) 2980 (1351.7) 30" (750)
B3151-29Z -- 12 Ga. (2.6) 24" (609.6) 27.00 (685.8) 3094 (1403.4) 30" (750)
B3151-30Z -- 12 Ga. (2.6) 24" (609.6) 28.00 (711.2) 3208 (1455.1) 30" (750)

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

161
 Pipe Supports, Guides, Shields & Saddles
Fig. B3154 - Short Insulation Protection Shield (TOLCO Fig. 220)
Fig. B3155 - Short Insulation Protection Shield with "Loc" Tabs (TOLCO Fig. 219)
Material: Steel (Stainless steel available)
Shields & Saddles
Supports, Guides,

Function: Designed for protection of foam, L

fiberglass, or high density insulation when used
with pipe hangers.
Finish: Pre-Galvanized
Order By: Figure part number and finish. Stock Size
L Shield I.D.
Note: See Selection Tables on page 160 for (Inside Dia.)
proper sizing.
B3154 Shield I.D.
(Inside Dia.)

Stock Size

B3155

B3155 same dimension as B3154 but with bottom tabs for centering and securing the shield to hanger.

Part Part Stock Size L Shield 'I.D.' Approx.Wt./100 Pipe Hanger Size
No. No. in. (mm) in. (mm) in. (mm) Lbs. (kg) in. (mm)

B3154-1X B3155-1X 18 Ga. (1.2) 8" (203.2) 1.90 (48.2) 36 (16.3) 11/2" (40)

B3154-2X B3155-2X 18 Ga. (1.2) 8" (203.2) 2.38 (60.4) 45 (20.4) 2" (50)

B3154-3X B3155-3X 18 Ga. (1.2) 8" (203.2) 2.88 (73.1) 54 (24.5) 21/2" (65)

B3154-4X B3155-4X 18 Ga. (1.2) 8" (203.2) 3.50 (88.9) 66 (29.9) 3" (80)

B3154-5X B3155-5X 18 Ga. (1.2) 8" (203.2) 4.00 (101.6) 75 (34.0) 31/2" (90)

B3154-6X B3155-6X 18 Ga. (1.2) 8" (203.2) 4.50 (114.3) 84 (38.1) 4" (100)

B3154-7X B3155-7X 18 Ga. (1.2) 8" (203.2) 5.00 (127.0) 93 (42.2) 5" (125)

B3154-8X B3155-8X 18 Ga. (1.2) 8" (203.2) 5.56 (141.2) 105 (47.6) 5" (125)

B3154-9X B3155-9X 18 Ga. (1.2) 8" (203.2) 6.64 (168.6) 126 (57.1) 6" (150)

B3154-10Z B3155-10Z 18 Ga. (1.2) 12" (304.8) 7.64 (194.0) 218 (98.9) 8" (200)

B3154-11Z B3155-12Z 18 Ga. (1.2) 12" (304.8) 8.64 (219.4) 247 (112.0) 8" (200)

B3154-12Z B3155-12Z 18 Ga. (1.2) 12" (304.8) 9.64 (244.8) 273 (123.8) 10" (250)

B3154-13Z B3155-13Z 18 Ga. (1.2) 12" (304.8) 10.76 (273.3) 304 (137.9) 10" (250)

B3154-14Z B3155-14Z 18 Ga. (1.2) 12" (304.8) 11.76 (298.7) 332 (150.6) 12" (300)

B3154-15Z B3155-15Z 18 Ga. (1.2) 12" (304.8) 12.76 (324.1) 360 (163.3) 12" (300)

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

162
 Pipe Supports, Guides, Shields & Saddles
Snap ‘N Shield™ Clevis
Size Range:
2.34" (59.4mm), 3.45" (87.6mm), 4.50" (114.3mm), 5.53" (140.4mm), 8.64" (168.5mm), and 8.64" (219.4mm) Shield Openings
Material: Plastic - Gray Thermylene P6-20FG-0738

Shields & Saddles

Supports, Guides,
Features:
• UV resistant
• Operating temperature -40°F (87.6°C) to +178°F (87.6°C)
• Paintable (preserves mechanical properties even after painting)
• Shield length is 12” (304.8mm).
• Non-adhesive surface for linear expansion of thermal insulation
• Protects insulation from damage caused by rubbing against other pipes and fittings.
Order By: Figure number.

Built-In
Clevis Shield Inside Approx. Clevis
Shock Indicator
Catalog Opening Wt./100 Hanger
Number in. (mm) lbs. (kg) Size
BPH250G 2.34” (59) 28.1 (12.7) B3100-2
BPH350G 3.45” (87) 40.6 (18.4) B3100-3
BPH450G 4.50” (114) 56.2 (25.5) B3100-4
BPH550G 5.53” (140) 74.2 (33.6) B3100-5
BPH650G 6.64” (168) 86.7 (39.3) B3100-6
BPH850G 8.64” (219) 150.0 (68.0) B3100-8

Copper Insulation Thickness

Tubing Sch. Insulation Thickness
Size 1/2” 3/4” 1” 11/2” 2”
40/80
1/4” BPH250 BPH250 BPH350 BPH350 BPH450 Pipe 1/2” 3/4” 1” 11/2” 2”
3/8” BPH250 BPH250 BPH350 BPH450 BPH450 1/4” BPH250 BPH250 BPH350 BPH450 BPH550
1/2” BPH250 BPH250 BPH350 BPH450 BPH550 3/8” BPH250 BPH250 BPH350 BPH450 BPH550
5/8” BPH250 BPH250 BPH350 BPH450 BPH550 1/2” BPH250 BPH250 BPH350 BPH450 BPH550
3/4” BPH250 BPH350 BPH350 BPH450 BPH550 3/4” BPH250 BPH350 BPH350 BPH450 BPH550
1” BPH250 BPH350 BPH350 BPH450 BPH550 1” BPH250 BPH350 BPH350 BPH450 BPH550
11/4” BPH350 BPH350 BPH350 BPH450 BPH550 11/4” BPH350 BPH350 BPH450 BPH550 BPH650
11/2” BPH350 BPH350 BPH450 BPH550 BPH650 11/2” BPH350 BPH350 BPH450 BPH550 BPH650
2” BPH350 BPH450 BPH450 BPH550 BPH650 2” BPH350 BPH450 BPH450 BPH550 BPH650
21/2” BPH450 BPH450 BPH550 BPH650 BPH850 21/2” BPH450 BPH450 BPH550 BPH650 BPH850
3” BPH450 BPH550 BPH550 BPH650 BPH850 3” BPH450 BPH550 BPH550 BPH650 BPH850
31/2” BPH550 BPH550 BPH650 BPH850 BPH850 31/2” BPH550 BPH550 BPH650 BPH850 BPH850
4” BPH550 BPH650 BPH650 BPH850 BPH850 4” BPH550 BPH650 BPH650 BPH850 BPH850

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

163
 Pipe Supports, Guides, Shields & Saddles
Snap ‘N Shield™ Series
Size Range:
21/4" (57.1mm), 31/4" (82.5mm), 41/4" (107.9mm), 51/4" (133.3mm), 61/4" (158.7mm), and 85/8" (219.1mm) Shield Openings
Material: Plastic - Black & White
Shields & Saddles
Supports, Guides,

Features:
• Ideal for horizontal pipe runs.
• Offers maximum protection for insulated pipe.
• Snaps directly onto channel.
• Shield length is 12” (304.8mm).
• Fast, easy installation – no tools required.
• Snap-on design eliminates shield movement, preventing insulation damage that can lead to costly leaks.
• Allows pipe to expand without damaging the insulation.
• Protects insulation from damage caused by rubbing against other pipes and fittings.
• Designed for side-by-side installations.
• The most reliable, durable, and cost-effective way to protect your insulation.
• Patent Pending.
Order By: Figure number.

Technical Specifications
Applications: Refrigeration, Air Conditioning, and Plumbing

Material: Basell Pro-Fax 8523 Polypropylene Copolymer

• UV resistant
• Operating temperature -40°F to +178°F
• Paintable (Preserves mechanical properties even after painting)
• Non-adhesive surface for linear expansion of thermal insulation

Certification: UL Classified for USA (UL-723 (ASTM E 84))

and ULC listed for Canada (ULC-S102.2).
Meets UL94 HB flammability standards

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

164
 Pipe Supports, Guides, Shields & Saddles
Snap’N Shield™ Series

Black Shields White Shields Gray Shields Inside Approx.

Part Part Part Opening Wt./100

Shields & Saddles

Supports, Guides,
Number Number Number in. (mm) Lbs. (kg)

BPS225B BPS225W -- 21/4” (57) 26 (11.8)

BPS325B BPS325W -- 31/4” (82) 37 (16.8)
BPS425B BPS425W -- 41/4” (108) 52 (23.6)
BPS525B BPS525W -- 51/4” (133) 69 (31.3)
BPS625B BPS625W -- 61/4” (159) 83 (37.6) Inside Opening
-- -- BPS862G 85/8” (219) 103 (46.7)

BPSCB BPSCW Universal 22 (10.0)

Cover

Copper Insulation Thickness

Tubing
Size 1/2” 3/4” 1” 11/2” 2”
1/4” BPS225 BPS225 BPS325 BPS425 BPS525
3/8” BPS225 BPS225 BPS325 BPS425 BPS525
1/2” BPS225 BPS225 BPS325 BPS425 BPS525
5/8” BPS225 BPS325 BPS325 BPS425 BPS525
3/4” BPS225 BPS325 BPS325 BPS425 BPS525
1” BPS225 BPS325 BPS325 BPS425 BPS525
11/4” BPS325 BPS325 BPS425 BPS525 BPS625
11/2” BPS325 BPS325 BPS425 BPS525 BPS625
2” BPS325 BPS425 BPS425 BPS525 BPS625
21/2” BPS425 BPS425 BPS525 BPS625 BPS862
3” BPS425 BPS525 BPS525 BPS625 BPS862
31/2” BPS525 BPS525 BPS625 BPS862 BPS862
4” BPS525 BPS625 BPS625 BPS862 BPS862

Sch. Insulation Thickness

40/80
Pipe 1/2” 3/4” 1” 11/2” 2”
1/4” BPS225 BPS225 BPS325 BPS425 BPS525
3/8” BPS225 BPS225 BPS325 BPS425 BPS525
1/2” BPS225 BPS325 BPS325 BPS425 BPS525
3/4” BPS225 BPS325 BPS325 BPS425 BPS525
1” BPS325 BPS325 BPS425 BPS525 BPS625
11/4” BPS325 BPS325 BPS425 BPS525 BPS625
11/2” BPS325 BPS425 BPS425 BPS525 BPS625
2” BPS425 BPS425 BPS425 BPS525 BPS625
21/2” BPS425 BPS525 BPS525 BPS625 BPS862
3” BPS525 BPS525 BPS625 BPS625 BPS862
31/2” BPS525 BPS625 BPS625 BPS862 BPS862
4” BPS625 BPS625 BPS862 BPS862 BPS862

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

165