By Appointment to Her Majesty The Queen

Supplier of Fire Detection Equipment

Kentec Electronics Ltd. Dartford, Kent. DA1 1JQ Kentec Electronics Ltd.

Life Safety
System
2014 - 2015 Specialists
 Contents
Introduction 3 32 Sigma Matrix
Conventional Fire Alarm Mimic Display System

Our In-house facilities 4 34 Sigma CP Network Diagram

Taktis 6 36 Sigma XT
Analogue Addressable Control Equipment Extinguishant Control Panel

Taktis Fire 8 38 Sigma XT+

Analogue Addressable 2-16 Loop Control Panels Extinguishant Control Panel Multi-Area

Taktis Vision 10 40 Sigma Si

Analogue Addressable Annunciators Extinguishant Status & Ancillary Units

Taktis Virtual Resource 12 42 Syncro XT+

A Comprehensive Suite of Software Based Tools Extinguishant Control Panel Multi-Area Addressable

Taktis Configure 14 44 Sigma XT Network Diagram

Loop Explorer 2 (LE2) Configuration Software

Taktis Network Diagram 16 46 PSU’s

Power Supplies

Syncro AS 18 48 Miscellaneous Items

Analogue Addressable 1-2 Loop Control Panels

Syncro 20 50 Elite
Analogue Addressable 2-4 Loop Control Panels Analogue Add. Fire Control Panels & Repeaters UL/ FM Approved

Syncro Repeaters 22 52 Sigma A-CP

Analogue Addressable Fire Control Panel Repeaters Conventional Control Panel UL Approved

Syncro Matrix 24 54 Sigma A-XT

Intelligent Fire Alarm Mimic Display System Extinguishant Control Panel UL/ FM Approved

Syncro Network Diagram 26 56 Sigma A-Si

Extinguishant Status & Ancillary Units UL/ FM Approved

Sigma CP 28 58 Syncro ASM

Conventional Fire Alarm Control Panels Marine & Offshore Analogue Addressable 1-2 Loop Control Panel

Sigma CP-A 30 60 Custom

2 AlarmSense Conventional Fire Alarm Control Panels Custom Engineered Solutions
Life Safety System Specialists

For almost 30 years Kentec has evolved into one of the World’s leading At Kentec we believe that the quality of our products should be
life safety control system manufacturers. The Kentec name has become paramount; rigorous testing procedures are employed at every stage of
synonymous with World class products, great service and excellent the manufacturing process to ensure that all equipment is supplied to the
support. Based in the UK, Kentec is a truly global supplier, exporting highest standards. For this reason we are confident in offering an industry
control equipment to over 80 countries Worldwide, and in many different leading 3 years warranty on all product that we supply. We also understand
languages. that service is a key part of how a manufacturer’s quality is judged. To this
end we have invested extensively not only in our manufacturing facilities
At the heart of our success is our philosophy of in-house manufacturing but in our support team including technical support and training.
and investment. 2013 will see further investment in plant, machinery and
processes at our Dartford based facility. Our focus is on customer service As part of our customer care Kentec offers first rate technical support
and we pride ourselves on quick turnaround and our ability to react quickly facilities and a dedicated team of highly trained personnel provide direct
to customer requirements and market trends. telephone assistance; this is backed up by regular technical e-mail bulletins.
We also have a team of dedicated trainers who provide our customers with
Kentec offers the most comprehensive range of conventional, analogue product training both onsite or offsite, UK and overseas.
addressable fire detection and extinguishant control panels available. Our
custom build service is also highly regarded in the industry and utilises Kentec’s products are tested and approved to international standards such
our expertise in control panel technology to design and build high quality as EN54, EN12094, UL and FM.
product to exacting customer specifications. Marine products are now
an important part of our product portfolio. In 2013 we will be introducing Kentec achieved ‘Investors in people’ accreditation in 2004. Our
the all new “Taktis” product range. Taktis will become one of the most management systems are ISO 9001:2008 approved and our policy for
comprehensive and dynamic products within the industry with its focus on environmental awareness was officially recognized in 2007 when we
added value and advanced technology. gained our ISO 14001 certification from BSI. In 2008 Kentec was proud to
be awarded the Royal Warrant of Appointment by Her Majesty The Queen.

MANAGEMENT
SYSTEMS

Certificate No. FM 32987 Certificate No. EMS 518118 Certificate No.360 KM 73505
BS EN ISO 9001: 2008 BS EN ISO 14001:2004 BS EN ISO 9001:2008 KM 96761

3
18
 Our In-house Facilities

At the heart of our business lie the many in-house facilities

that are at our disposal. From the initial design process,
to sheet metal fabrication, to powder coating and printing
through to panel construction, we have full control at every
stage of our manufacturing process allowing us to offer
industry leading delivery times and with quality that you can
have confidence in.

Our Dartford based “World Class” facility which was

expanded in 2009 will be further enhanced in 2013.

Integral to our sheet metal fabrication department is a state

of the art computer controlled Amada break press. In 2013
a second, larger and more powerful Amada break press will
be added to further increase our capacity.

We also have a full range of bending, cropping, studding and

welding equipment allowing us the capability and flexibility
to produce single items or volume product.

Our versatile finishing department featuring a semi-

automatic powder coating plant continues to provide all our
metal component finishing needs.

4
Our printing department deploys state of the art digital
printing with the centre piece being our OCE Arizona
digital UV large format printer. The Arizona printer
has revolutionised the department offering increased
capacity, consistency and quality.

Electronic Sub assemblies are produced using our

fully automated surface mount production line which
was further enhanced in late 2012 and again early
in 2013. We systematically utilise both optical and
electrical automatic test equipment to ensure each
and every assembly is built to the same high standard
and is fault free.

All panels supplied by Kentec are manufactured and

assembled in-house in the U.K. Before despatch all
panels undergo a rigorous testing procedure, they are
then given a final visual inspection.

To underpin our industry leading in-house

manufacturing activities we employ teams of qualified
and experienced mechanical, software and electronic
hardware developers and technicians dedicated to
both new product developments and existing on
going product support.

5
18
 Taktis Analogue Addressable Control Equipment

6
Taktis Overview

Analogue Fire Detection

The all new Taktis product range of fire alarm control equipment combines the very Each 2 loop module slot can be fitted with a variety of option boards to provide
latest hardware and software to produce a control and indication system, which is alternative functionality. Modules can be “hot swapped” to minimise system
powerful and sophisticated, yet simple to use and understand. degradation during fitting and all inputs and outputs can contribute to the Taktis,
industry-leading cause and effect capability.
The flexibility of the Taktis platform is such that it can be re-configured to realise
many other control and indication applications, with direct integration into intelligent These modules include:
buildings.
8 zone conventional detection board
Moving away from the simple, price driven competitive model used by most
manufacturers today, the Taktis concept is designed to add value to System 4 way sounder output board
Designer, Integrator, Service provider and the end user.
8 way volt free relay contact board
Developed from the “ground up” by one of the industries’ leading design teams and
16 channel programmable I/O board with digital inputs and open collector outputs
using some of the most advanced technology available, Taktis is designed as one of
the most powerful, intelligent and technically robust fire alarm products available. Media Gateway communications board

Not only do the products and services offered under the Taktis brand provide Taktis “Bridge” Network Card (connect Taktis to your existing Syncro network)
solutions to the most technically challenging applications in life safety, Taktis will
deliver added value, market advantage and a competitive edge to your business. By taking advantage of the unique user interface it is possible to further customise the
control panel so it can meet specific alternative requirements such as local regional
The modular nature of the Taktis system allows all field wiring to be connected to variances, alternative additional functionality or corporate livery. Although this level
a passive mother board enabling addition, re-configuration or replacement of all of customisation is not generally a user feature, the architecture of the Taktis control
electronic hardware without the need to disconnect any field wiring. system makes customisation almost limitless.

This modularity also allows each panel to be customised with addressable loop
detection circuits, conventional detection circuits, relay cards, additional sounder
outputs or programmable I/O modules as required.

7
 Taktis Fire Analogue Addressable Taktis Features
2-16 Loop Control Panels Compliant with EN54-2, EN54-4 and EN54-13

Detector protocol selectable via front panel menu screens

Up to 144 zone LED indicators on standard models

Support for up to 2000 zones and zone LED indicators

Built in programmable I/Os

Up to 512 programmable I/O via optional plug in cards

Modbus, LonWorks and BACnet interface options

Full colour, 7” 800 x 480 touch screen graphical display

Fully automatic display brightness adjustment

80 character point and zone text

Over 4000 sub address points per panel

Over 5000 cause and effect outputs

Over 20,000 cause and effect entries

Up to 5000 software groups

Maximum of 50,000 devices NOT and TIME as well as

COINCIDENCE, OR and AND operators in cause and effects

Option to “invert” inputs and outputs

9999 event log with one second resolution

Powerful, standard configuration templates

Network up to 128 panels

Configurable via USB port to PC or memory stick

Optional Media Gateway communications card

8
Taktis Overview Compatible Equipment & Extras

Analogue Fire Detection

With the increasing demands for power in fire detection and alarm systems, Taktis Fire control panels are
well placed to meet current and future needs.

All panels are available with either a 5.25A, 24V power supply capable of charging up to 26Ah batteries
or a 10.25A, 24V power supply capable of charging up to 45Ah batteries. Taktis Fire can be supplied with
one of a range of remote power supply units making the control panel smaller and easier to install.

Up to 500 milliamps is available for each detection loop allowing for a generous quantity of loop powered
devices.

The four sounder circuits are each capable of supplying up to 2.5A at 24V to audio and audio visual
Selection of I/O boards
devices.

The addition of a Taktis Media Gateway communications device configured to report to the Virtual
Resource servers and subscription to one or more Virtual Resource browser based software modules,
allows systems to be managed remotely and from any location in a simple and efficient manner.

Taktis Media Gateway also provides the interface between control systems and other products
and utilities such as PC graphics, Voyage Data Recorder and a growing number of third party Taktis
compatible products.

Configurable serial ports will allow connection to BMS systems using LonWorks, Modbus or BACnet
protocols. VR Taktis Media Gateway

Taktis fire systems are scalable with Taktis Net Enhanced High Speed Networking. This allows up to
128 panels to be connected together as a fully fault tolerant networked system with rapid inter panel
communications and up to 1.2km of standard two core fire resistant cabling between nodes.

Each panel can be configured to display all or any events from any other panel allowing master/slave,
multiple master/slave or peer to peer configuration.

Sophisticated network analysis tools provide the ability to identify connection problems instantly and the
commissioning mode allows individual panels to be prevented from transmitting events to the network
while maintaining communications.
Taktis Network Card
Adding a Taktis “Bridge” Network Card to your Taktis Panel or Taktis Network provides an interface
between existing Syncro and Taktis Control Systems providing backward compatibility and a unique
upgrade path.

Taktis Fire 2-16 Loop Panel 9

 Taktis Vision Analogue Addressable Annunciators Taktis Vision Features
Robust, full colour, 7” 800 x 480 touch screen graphical
display

Full indication of all information displayed at the fire control

panel

Automatic display brightness adjustment

Silenceable internal sounder

Connections Via:

Control panel RS485 bus

Option to connect to control panel network

Low current, 24V DC powered

Slim compact construction

Configurable functionality

Configurable languages

Optional Enable keyswitch

10
Taktis Vision Overview Compatible Equipment & Extras

Analogue Fire Detection

Taktis Vision provides a means of allowing full display and optional control of the Taktis fire alarm control
panel from a small and unobtrusive local control station.

Based on an all new hardware and software platform, the large, full colour graphical display with touch
screen functionality, delivers information on the status of the fire alarm system to single or multiple
locations.

Taktis Vision repeaters can be configured to offer full display and control to replicate the functionality of
the fire control panel or to operate as a simple, display only device for applications where access to control
the fire alarm system would be inappropriate.
Taktis Network Card
For other annunciation and control applications, Taktis Vision can be configured to provide customisable
switches and indications for a host of fire system ancillary functions.

Taktis Vision may be connected to the fire control panels’ fault tolerant, ancillary RS485 bus or to the fire
alarm panel fault tolerant network using standard, fire rated cable offering flexibility in system wiring.

Available in several standard formats, Taktis Vision can be mounted directly onto a wall, be recessed
using our quick-fix adaptor frame or fully flush mounted. Special enclosure finishes and colours are also
available to match existing decor.

Multi Purpose Flushing Collar

11
 Taktis Virtual Resource A Comprehensive Suite Taktis VR Features
of Software Based Tools Unique Life Safety management utility

Remote access to system data from anywhere

Revenue driver for all business sizes

Cut costs and drive up productivity

Reduce environmental impact through technology

Modular application based tool set:

VR Access - View and mange my projects

VR Vault - Store and retrieve system documentation
VR Service - Manage, add value and improve
compliance
VR print - Virtual printer

More to come…
More VR applications will be added to the list providing users
with further enhancement to their value and revenue streams

12
Taktis VR Overview VR Vault

Analogue Fire Detection

To compliment the new, market leading range of control systems. Virtual Resource is a Subscribers to Virtual Resource can securely store system and site related documentation
unique suite of software tools aimed to deliver a whole new dimension in Life Safety System on our permanently backed up servers using VR Vault.
Management.
VR Vault provides a convenient and permanently accessible storage location for all
It provides System Designers, Integrators and Service Companies with the ability to remotely documentation related to an installation including installation drawings, commissioning
access and comprehensively manage any system using intelligent analysis of data collected details and certificates, service and maintenance records, general notes and any other
from those systems. End-users and facilities managers can also greatly benefit from the documents related to the installed system that the user requires.
powerful feature set that comes with Virtual Resource.
VR Service
Virtual Resource is based on technology successfully trialled for many years and is one
of the most technically advanced management tools for fire detection and other safety VR Service provides a means to set up a comprehensive fire alarm system servicing
systems on the market. regime adding benefit to both the end customer and Service company.

With Virtual Resource, Installers and Service providers are able to offer market leading Site details can be imported from VR Access or added and set up manually to create
functionality through remote management and provide improved service at lower cost and customer records.
greater efficiency.
Service frequency and device activation list schedules can be set and resources allocated
The remote management features offered by Virtual Resource can result in reduced fault including, travelling time and estimated time to complete the service providing essential
call outs, improved servicing regimes, more effective maintenance, reduction of unwanted data for planning service engineer’s activities. Service engineers can view and print their
alarms and improved overall service to the end user. work schedules including site specific notes and previous service records directly from the
system if required.
Whether you are a Service provider, building owner or facilities manager, change the way
you think about managing your Fire Detection System. Taktis VR you can reduce costs, add VR Print
value and improve service integrity by employing the latest communication and analytical
technologies. Designed to replace panel mounted printers which are inherently difficult to manage and
provide very limited information. VR Print provides a secure method of storing and recalling
VR Access the control system events via any web browser. The user can simply view the systems
events on line, print PDF reports or download the data in formats such as csv for further
Gain access to data from all of your systems, assess performance, check status and make data analysis.
decisions based on facts, not assumptions.

VR Access allows a Virtual Resource enabled fire system to periodically report its status to
the secure servers and allows a VR Access subscriber to view the latest status report via
any web enabled device.

13
 Taktis Configure Loop Explorer 2 (LE2) Taktis LE2 Features
Configuration Software Based on the industry leading Loop Explorer

Delivered and managed via the new taktisvr.com web site

No more out of date versions in circulation

Many new features and benefits

Time manager
Group Manager

1000’s of Cause & Effect options

Additional C & E operators

“Not” and Time

Powerful templates

Favourite device tab

Language support

14
Taktis LE2 Overview

Analogue Fire Detection

The powerful central processor and extensive on board expandable memory in the Taktis LE2 can also be used to select, (where applicable) the appropriate detection loop protocol.
Fire control system, allows demanding configuration options and many thousands of cause It is possible to run different loop protocols on individual loop cards.
and effects to be processed quickly and efficiently.
Powerful standard templates allow rapid configuration of common fire system
Logical operators such as COINCIDENCE, AND, OR, NOT, TIME OF DAY and INTERVAL configurations for applications such as high rise buildings or alarm verification from hotel
TIME along with the ability to group inputs and outputs into collections other than zones rooms.
and the capability to configure up to 2000 zones produces a system capable of fulfilling the
most demanding of control applications. Cause and effect processing power is now practically limitless allowing the configuration
of large, complex networks with ease. Access to LE2 is via a secure web server, so users
A standard USB port allows configurations stored on a USB memory stick to be loaded to with the appropriate credentials have permanent access to the latest version ensuring that
the control panel without the use of a PC. the most recent enhancements are always available. LE2 can be customised by the user
so that language or specific terminology can be set as defaults for all systems that are
The Loop Explorer 2 (LE2), PC configuration software provides a familiar, simple to use PC
configured using LE2. Custom changes are stored on our servers, once more ensuring
application with the power to produce the most complex configurations via an easy to use
that all authorised users have access to the latest customised version.
and intuitive interface.
For added convenience, Taktis Virtual Resource subscribers can store LE2 configuration
Maintaining the look and feel of the industry leading original Loop Explorer I configuration
files on our secure servers ensuring that the site configuration is always backed up and
utility, LE2 is itself highly configurable allowing customisation of languages, colour schemes
available to users with the appropriate access rights.
and company logos and allowing exposure to single or multiple detector protocols to be set
for each user.

Additional logical operators for NOT and TIME functions for use in cause and effects and
the inclusion of “groups” (collections of devices not necessarily in the same zone) increase
the power and flexibility of LE2 to far beyond what was achievable with its forerunner and
most other products currently on the market.

15
 Taktis Network Diagram
High Integrity Configurable Network
Cloud Servers
GSM
IP Media Gateway
Dial-Up

Taktis Fire
2 - 8 Loop Analogue
Addressable Control Panel

24V DC

Taktis Virtual Resource

Taktis Vision
VR Access - Access data
Configurable Fire Alarm
from all your systems
VR Vault - Secure document vault
Repeater
VR Service - Complete service
management utility with automated
data transfer
Loop 3 - Loop 8

VR Print - Eliminates need for

panel mounted printers
(if fitted)

Each bank of 2 loops

can be different protocols.
Loop 2

Each loop is capable of

I/O
hosting up to:
Loop 1

126 devices (Apollo) or Taktis Fire

240 devices (Argus Vega) or
127 devices (Hochiki).
2 - 8 Loop Analogue
Addressable Control Panel
16
 Analogue Fire Detection
Plug in
slots

IO Cards
K772 K791 K792 K793
16 Channel 8 Way 8 Way Conventional 4 Way
I/O Board Relay Board Zone Board Sounder Board

RS485 bus

Taktis Fire
2 - 8 Loop Analogue
Addressable Control Panel

The Taktis system is

compatible with Apollo,
Argus Vega and Hochiki
protocols. Panels of any of 24V DC
the above protocols can be
used on the same network.

Taktis Vision
Up to 128 Panels/ Configurable Fire Alarm
Repeaters can be Repeater
added to the network.

Loop 2 Loop 3 - Loop 16

(if fitted)
Each bank of 2 loops
can be different protocols.

I/O Each loop is capable of

hosting up to:
126 devices (Apollo) or

Loop 1
Taktis Fire 240 devices (Argus Vega) or
2 - 16 Loop Analogue 127 devices (Hochiki).
Addressable Control Panel
17
18
 Syncro AS Analogue Addressable Syncro AS Features
1-2 Loop Control Panels 16 zonal LED indicators

2 programmable sounder circuits

5 programmable inputs

3 programmable relays

3A power supply

Large graphic display

Real time clock

Expandable from 1 to 2 loops*

Certified to EN54-2/ EN54-4

Up to 512 additional programmable I/O via

Syncro I/O modules *

Powerful, network wide cause and effects *

Sensitivity adjustment and Drift Compensation

Can be networked with Syncro control panels *

Compatible with Focus and View repeaters *

Supports Apollo, Argus Vega and Hochiki protocols

Same look and feel as Syncro range

Stores 500 last events in event log

Dial up modem connection available

Compact, stylish enclosure

Installer friendly, removable equipment chassis

Different language and character set variants available

Fully EN54-2 and EN54-4 compliant improved front

loading Printer option * **

*These items not available on Syncro AS Lite panel

** Can be fitted to M3 size enclosure only

18
Syncro AS Overview Compatible Equipment & Extras

Analogue Fire Detection

The Syncro AS is a powerful and versatile Single or two Loop Analogue Addressable Fire Control Panel.

Syncro AS fully supports all devices from the leading, open protocol detector manufacturers and can be
supplied with Apollo (S90/XP95 /Discovery), Argus Vega or Hochiki ESP loop drivers, all capable of
providing up to 400 milliamps of loop current for the most demanding applications.

An integral 3 Amp power supply and temperature compensated battery charger provides ample power for the
two, 1 Amp rated standard sounder outputs, loop powered sounders and other devices.

Syncro AS is also available as a Lite version offering a very cost effective solution for smaller standalone
installations requiring only one detection loop.
Selection of I/O boards See website
The Lite version does not support the following:
Second loop, Printer output, Networking and connection of I/O boards or the View repeater.

Connectivity
Syncro AS connects seamlessly to other Syncro AS, or Syncro multi-loop panels and repeaters via the fully
fault tolerant and robust Syncro network. The Syncro AS supports all Syncro serial bus peripherals such as
View repeaters, 16 channel I/O boards, Relay boards, Sounder boards and Conventional Zone boards to
provide an additional 512, fully programmable points. 16 zonal LED indicators are provided as standard and the
panel will support up to 500 network wide software zones as per Syncro multi-loop panels.
OpenConnect BMS Communication Interface See DS66
Powerful Software
Programming, including powerful cause and effect functionality can be achieved using the intuitive Loop
Explorer configuration utility familiar to Syncro panel users. The new Loop Explorer 2 will also support all of
the Syncro AS product family.

The Guide graphics system or a modem for remote system interrogation by telephone lines may also be
connected to Syncro AS panels via the RS232 serial connection.

Ease of Installation
The elegant and simple construction of the panel enables the chassis to be completely dismantled by Syncro Net Network Card See DS23
removing just two screws. The outer cover can also be detached by removing two hinge pins making first
fix installation very simple and enabling the sensitive electronic parts to be stored safely for re-fitting at the
commissioning stage.

Housed in the same installer-friendly and attractively styled enclosure as the popular Sigma CP
(Conventional) and Sigma XT (extinguishant) range of fire control panels, Syncro AS combines compact and
practical styling with the programming power and connectivity normally associated with much larger systems.

19
 Syncro Analogue Addressable Syncro Features
2-4 Loop Control Panels 2 or 4 loop versions as standard (for 6-8
loop versions see DS57)

Larger enclosure available (fits 24A/H SLAs)

Loopless panel option (repeater)

0, 16, 48, or 96 zone indicators

Option for Enable Control keyswitch

Fully supports Apollo, Argus Vega & Hochiki protocols

Network up to 64 panels/repeaters

4 programmable sounder circuits as standard

5.25 amp power supply to EN54 part 4

Large graphic display

In built help and alarm information screens

Certified to EN54-2/ EN54-4

Real time clock

Supports Apollo, Argus Vega and Hochiki loop

powered sounders and beacons

Sensitivity adjustment and Drift Compensation

Stylish enclosure design

Soft-touch tactile buttons

2 programmable function buttons

3 programmable front panel mounted LED’s

Improved Front loading Printer (optional)

Up to 512 programmable inputs/outputs per panel

via 2 wire RS485 serial link (optional)

Simple Windows® graphical configuration utility

20
Syncro Overview Compatible Equipment & Extras

Analogue Fire Detection

The Syncro Multi Loop Analogue Addressable Fire Control Panel range offers a powerful and scalable
solution for fire detection and alarm systems.

With proven and mature software at its heart, the Syncro range benefits from many years of development
and refinement to provide a fire alarm control panel range of outstanding robustness, versatility and flexibility.

Syncro multi-loop fire panels have a large clear display, context sensitive help screens, easy navigation
menus, versatile configuration options and simple controls all enhanced by the power and flexibility that
comes from compatibility with other components of the multi-loop Syncro system and peripherals.

Syncro fire panels fully support all devices from the leading, open protocol detector manufacturers and can
Syncro AS See Pg. 18/ DS47
be supplied with Apollo (S90/XP95 /Discovery), Argus Vega or Hochiki ESP loop drivers, all capable of
providing up to 400 milliamps of loop current for the most demanding applications.

An integral 5.25 Amp power supply and temperature compensated battery charger provides ample power for
The 4 standard sounder outputs, loop powered sounders and fully loaded loops of devices.

Connectivity
Syncro fire panels connect seamlessly to Syncro AS fire panels or other Syncro multi-loop panels and
repeaters via the fully fault tolerant and robust Syncro network. The network topology can be configured for
either a fully secure “loop” or as an “open ended” network for replacing older systems and using existing
cabling. Selection of I/O boards See website

The Syncro range supports a selection of serial bus peripherals such as View repeaters, 16 channel I/O
boards, Relay boards, Sounder boards and Conventional Zone boards to provide an additional 512, fully
programmable points. 0, 16, 48 or 96 zonal LED indicators can be provided as standard and the panel will
support up to 500 network wide software zones.

Powerful Software
The long established Loop Explorer configuration utility can be used to configure the Syncro range. With
the all new Loop Explorer 2 offering a simpler and more intuitive programming configuration tool capable of
realising the largest and most complex fire alarm systems with ease. OpenConnect BMS Communication Interface See DS66

The Guide graphics system or a modem for remote system interrogation by telephone lines may also be
connected to Syncro panels via the RS232 serial connection. All of the above combined with a host of
different language options (including those with Cyrillic characters) produce an outstanding and competitive,
world class fire alarm control panel range.

Ease of Installation
The elegant and simple construction of the Syncro panel range with full mechanical protection of all internal
electronics, ensures ease of installation and protection of the vital parts during installation.

Housed in installer-friendly and attractively styled enclosures, Syncro fire panels combine compact and
practical styling with powerful programming and connectivity to realise the largest of systems.
Syncro Net Network Card See DS23 21
 Syncro Repeaters Analogue Addressable
Fire Control Panel Repeaters

Syncro View

Syncro Ident

Syncro Focus+ Syncro Response

22
Syncro Response Syncro Focus & Focus +

Analogue Fire Detection

Syncro Response is a full function repeater panel identical in appearance and The simple and attractive Focus repeater panel can be connected to any point on a
complementary to the Syncro control panel range. Syncro network to provide an additional compact display point for all events on the
fire alarm system.
Offering the full range of indications, controls and configuration options as Syncro
fire alarm panels, Syncro Response connects to the Syncro network and provides a Using the same large format graphics display as the main control panel ensures that
powerful means of remote indication and control for an entire fire alarm system. a clear and concise text indication of the system status is given at all times.

The 5 inbuilt programmable relays, I/O board serial bus and auxiliary 24V DC supply Primary indication is provided by the full graphic LCD with additional indications for
allow the Syncro Response repeater to provide additional system inputs and outputs power, fire, fault and disablement conditions provided by discrete LEDs.
to complement those provided by Syncro fire alarm control panels.
Controls are kept to a minimum with only two navigation buttons and a silence buzzer
Syncro Response repeaters can be provided with 0, 16, 48 or 96 zonal fire indicators button on the Syncro Focus and additional Silence Alarm, Reset and Re-sound alarm
and with an optional printer. A single 16 channel I/O card, 8 way relay card, 6 way buttons on the Focus+.
sounder card or 4 way conventional detection zone card can be fitted inside the
Syncro Response and a maximum of 32 I/O boards in total can be connected to the Ideal for additional building entrances, security desks or nurses stations this unit
serial I/O bus connection. provides an economical and more compact alternative to a full function, Syncro
Response repeater panel.
All Syncro Response repeaters are supplied with a Syncro network card pre-installed
for direct connection to a fault tolerant Syncro network. Syncro Focus connects directly to a fault tolerant Syncro network and can also be
used as a network booster to extend cable runs beyond the specified lengths as
required.

Syncro View Syncro Ident

The Syncro VIEW fire alarm repeater provides an alternative to Syncro Response or Syncro Ident panels provide a compact and attractive display for up to 24 indications
Syncro Focus network connected repeaters and provides a cost effective, simple and from a Syncro or Syncro AS fire control panel.
convenient method of extending the controls and indications of the Syncro fire alarm
control panel to other locations. As with all inputs and outputs on the Syncro system, each indicator is fully
programmable to indicate a variety of events as well as being fully programmable via
The large, graphic LCD, brightness LED indicators and full set of controls duplicate cause and effects to operate in response to logically connected inputs.
the indications and controls on the Syncro fire alarm control panel at up to 15
additional locations via a (separate to the Syncro network) simple, two-wire serial Each indication defaults to a zonal fire indicator but may be configured via the Loop
data connection. Explorer configuration utility to operate upon any event type or combination of inputs.

Ideal for locations where a control and indication point smaller than a full fire alarm Requiring only a low current 24V power supply and a 2 core data connection to
control panel is required, the Syncro VIEW is available in either a 24V DC powered the fire panel, Syncro Ident panels can be installed quickly and easily to provide
option (which can be powered via an additional 2 cores from the Syncro control panel supplementary information on the status of the fire alarm system with the minimum
auxiliary 24V DC supply) or a 230V powered option with local battery back up. of cost and effort.

23
 Syncro Matrix Intelligent Fire Alarm Syncro Matrix Features
Mimic Display System Up to 504 LED’s can be controlled from any
Syncro or Syncro AS panel

Full colour printing

Available in a range of standard enclosures to

suit any applications

Bespoke sized units can be made upon request

Choice of Red, Green or Yellow LED’s

Available with or without controls

Same look and feel as Syncro range

Syncro Matrix can easily be upgraded on site

with minimal cost and effort

EN54-4 approved PSU (optional)

Configured via standard Loop Explorer Software

24
Syncro Matrix Overview Enclosure Size Options

Analogue Fire Detection

Syncro Matrix is an innovative fire alarm mimic system which can be connected to any panel in the Syncro
and Syncro AS fire alarm panel range.

The Syncro Matrix system uses flexible, fibre optic light guides to illuminate areas on a floor plan, laid over
a high resolution grid. This unique system dispenses completely with wiring and enables indicators to be
moved, removed or added on site without the need for any wiring.
185
303
Syncro Matrix can be supplied with or without common LEDs and controls. Optional LEDs indicate Power
on, Fire, Fault and Disablement and optional controls are for Alarm silence, Buzzer silence, Lamp test and
Reset.
M2 385mm W x 310mm H x 90mm D
Housed in attractive, slimline enclosures to match Syncro and Syncro AS fire alarm panels and with high
quality, full colour or monochrome floor plans, Syncro Matrix provide a clear, geographical indication of fire
alarm or other system activation enabling speedy identification of the source of an alarm or other event.

Configuration
The Syncro Matrix has a default configuration of zonal fire for the first 24 indicators but all indicators can 225
be configured to operate upon any event type and at point, zone or group level via Kentec’s powerful and 400

intuitive Loop Explorer configuration programme.

Indicators may also be configured to flash or illuminate steadily upon activation. This flexibility allows Syncro
Matrix mimics to be used for many other applications other than as a standard fire alarm indicator panel. S3 500mm W x 355mm H x 117mm D

Future Proofing
The Syncro Matrix is ideal for buildings such as hospitals where the building layout may evolve over a period
of time.
400
303
As the building changes, so too can Syncro Matrix, with very little cost or disruption. Modifying the mimic
is very straightforward and can be carried out on site without the need for any wiring or special tools. The
positions of the indicators can be freely moved anywhere on the grid and new indicators can be added using
kits of lenses and light pipes which are available. Additional mimic PCB’s are also available in kit form to
enable the capacity of the mimic to be increased as required.
M3 385mm W x 520mm H x 110mm D
Custom Solutions
Where the requirements of the installation exceed the standard range of Syncro Matrix panels, completely
515
bespoke solutions are available. 400

The enclosure size, mimic viewing area, colour and finish can all be tailored for the individual requirements of
the site, including the option of surface or flush construction.

Up to 32 mimic PCB’s can be connected to a single Syncro AS, Syncro or Syncro Response panel giving a
total of 504 LED’s that can be individually configured via the standard loop explorer configuration software.

To increase the flexibility of this product further, the LED extension boards are available in with yellow or green
indicators fitted.
S4 500mm W x 650mm H x 137mm D 25
Syncro Network Diagram Supports all
Syncro I/O
modules.
RS485

High Integrity Configurable Network

Up to 16 GUIDE An RS232 to RS485 The GUIDE dongle is fitted to Full function repeater
Repeaters may be data converter is the RS232 serial interface inside panels are loopless,
connected to a GUIDE supplied with the GUIDE the Syncro or Syncro Response they come with a choice of
system via a LAN (Local system. Panel. It converts data to RS485 and 0, 16, 48 or 96 zone
Area Network) must be fitted for the system to work. indicators.

RS485 RS232 Syncro Response

Full Function Repeater
Syncro GUIDE LAN
Syncro GUIDE
Repeater Facility for Graphical User Interface for
GUIDE System Control panels
fire Detection Equipment are supplied
with 2 or 4 detection
loops and a choice
of 0, 16, 48 or 96
zone indicators.
Loop 2 Loop 3 Loop 4
(if fitted)

K555
Network Card
Required

I/O
Syncro
Loop 1

Analogue Addressable
Control Panel

Each loop is capable Supports all

of hosting up to: Syncro I/O
126 devices (Apollo) or modules.
240 devices (Argus Vega) or
127 devices (Hochiki)
RS485 RS232 24V DC or
Syncro Focus
230V AC Network LCD Repeater
26
 Analogue Fire Detection
RS485

K560 K547 K546 K545

16 Channel 8 Way 6 Way 4 Way Conventional
I/O Board Relay Board Sounder Board Zone Board

24V DC 24V DC 24V DC 24V DC

K555
I/O

Loop 1 Loop 2
Network Card
Required

(if fitted)
Syncro View
Local LCD Repeater

Syncro AS
Analogue Addressable RS232 24V DC or
Control Panel 230V AC

Each loop is capable

of hosting up to:
Up to 64 Panels/ 126 devices (Apollo) or
Repeaters can be 240 devices (Argus Vega) or
added to the network. 127 devices (Hochiki)

K556
Modem Card Syncro Ident
Programmable LED
The Syncro system is
compatible with Apollo,
Indication Panels
Argus Vega and Hochiki
protocols. Panels of any of
the above protocols can be 24V DC or
used on the same network. 230V AC

Syncro Focus +
Network LCD Repeater The Syncro network A mixture of up to 32
can be interrogated devices (including
remotely by using the K556 Syncro View, Ident and
modem module (normally Matrix) can be fitted to each
fitted inside panel) panel on the RS485 serial Syncro Matrix
connected via the telephone. interface. The maximum
number of Syncro View Fire Alarm Mimic
24V DC or panels on a single RS485 Display System
serial interface is 15.
230V AC

24V DC or 27
18
230V AC
 Sigma CP Conventional Fire Alarm Control Panels Sigma CP Features
Fully certified to BS EN54-2 and BS EN54-4

2-wire and standard versions in 2, 4 or 8 zones

Compatible for use on BS5839: Part 1: 2013 installations

2-wire repeaters and ancillary boards

Fully programmable using simple menu options

Adjustable sounder delay time

Sounder configuration options
Zonal sounder delay detectors only
Zonal sounder delay call points only
Coincidence input selection
I.S Barrier selection by zone
Short circuit fire by zone
Non latching zones
Silent zones
Zone input delay
General panel configuration

Simple, single board construction

Installer friendly

Compatible with wide range of detection devices

Two monitored sounder outputs

3 Amp power supply

Auxiliary power output

28
Sigma CP Overview Compatible Equipment & Extras

Conventional Fire Detection

The Sigma CP range of conventional fire control panels are high specification, fully featured control units
designed for the most demanding of conventional fire detection and alarm system applications.

Sigma CP is available with two, four or eight detection zones in standard or installation saving, “two wire”
versions. The extensive range of configuration features available ensure suitability for new installations or
panel replacements on older systems.

Configuration options are stored in non-volatile memory and are easily accessed via an intuitive user interface
which allows the configuration data to be viewed and changed simply and easily.

Sigma CP control panels are compatible with most standard, conventional detectors, call points and
sounders and are also compatible with “two wire” detector bases from Apollo and Hochiki.
Sigma CP-R Repeater Panel See DS39
An integral three Amp power supply and temperature compensated battery charger provides ample power
for the two, 0.5 Amp rated standard sounder outputs, zonal sounder outputs on “two wire” versions and an
auxiliary 24V supply output.

Powerful Features
The simple and intuitive programming interface on Sigma CP panels allows simple configuration of many
parameters by entering simple codes which are listed on the inner door look up table and in the operation and
maintenance manual. Configurable options include sounder delays, short circuit triggering of zones, non-
latching zones, silent zones, I.S. barrier compatible zones and system disablements.

Connectivity Sigma CP Ancillary PCB See page 39

Sigma CP control panels have a dedicated; two wire serial bus for connection of repeater panels, Ancillary
relay boards or zonal sounder extension boards. Up to seven units may be connected to the serial bus which
can be up to 1200 metres in length. All units connected to the serial bus are fully monitored and the control
panel will announce a fault condition showing the address and type of any units that fail or are disconnected
after the panel has been configured to recognize them.

“Two wire” versions of Sigma CP can have detectors, call points and standard, polarized sounders connected
to the same two core cable, greatly reducing installation time and cost on some installations.

These “two wire” versions also provide the capability of zonal sounders which may be configured as zonal
alarm (sounders operate only in the zone of activation), common alarm (all sounders in all zones operate) or Sigma Sounder - Sounder Controller Units See DS48
two-stage alarm (sounders are continuous in the zone of activation and pulsing in all other zones).

Ease of Installation
The elegant and simple construction of the panel enables the chassis to be completely dismantled by
removing just two screws. The outer cover can also be detached by removing two hinge pins making first
fix installation very simple and enabling the sensitive electronic parts to be stored safely for re-fitting at the
commissioning stage.

Sigma CP panels combine compact and practical styling with the programming power and connectivity
required for the most complex and demanding conventional fire alarm system installations.

29
 Sigma CP-A Conventional Fire Alarm Control Panels Sigma CP-A Features
AlarmSense Compatible 2-wire Fully compliant with BS EN54-2 and BS EN54-4

Allows systems to be installed in accordance with

BS5838: Part 6

2 wire systems, reduces installation cabling

2-wire repeaters and ancillary boards via serial bus

Fully programmable using simple menu options

Adjustable sounder delay time

Sounder configuration options

Zonal sounder delay for detectors only

Zonal sounder delay for call points only

Coincidence output via ancillary board

Short circuit fire selectable by zone

Non latching selection by zone

Silent zones (common sounder outputs)

Zone input delay for sprinkler system connection

AlarmSense® local alarm feature supported

Simple, single board construction

Installer friendly

Compatible with all AlarmSense® devices

Two conventional monitored sounder outputs

3 Amp power supply

Auxiliary power output

30
Sigma CP-A Overview Compatible Equipment & Extras

Conventional Fire Detection

The Sigma CP-A AlarmSense® range consists of a series of conventional, 2, 4 and 8 zone fire alarm control
panels..

The AlarmSense® system enables all detection and sounder devices in a given zone to be wired to the same
pair of cables thus greatly reducing the cabling and installation requirements and hence costs.

The AlarmSense® range of devices includes smoke and heat detectors, call points, base sounders, base
sounder/beacons and relay units – all wired to the same pair of cables.

Having sounders and sounder beacons installed on the same cabling as detectors and call points allows
all systems to be configured for common, zonal or two stage alarm by simply setting one of the panels
Sigma CP-R Repeater Panel See DS39
configuration options.

Selection of the AlarmSense® local alarm feature at sounder or sounder beacon bases invokes the
alarm verification feature. This is particularly useful in Houses of Multiple Occupation such as student
accommodation or nursing homes. When sounder or sounder beacon bases are selected for local alarm
mode, alarms are restricted such that only the sounder connected to the activated detector will operate
initially. The panel will attempt to reset the activated detector after a time delay and if successful no further
alarms are sounded. If the detector re-activates after being reset, a general alarm will sound throughout the
premises.

Activation of a second detector or a call point will sound the general alarm immediately.
Sigma CP Ancillary PCB See page 39
The alarm verification feature of the Sigma CP-A control panel greatly reduces the risk of unwanted alarms or
call outs while still providing secure, high quality fire protection throughout the premises.

All control panels have an integral, 3 Amp mains powered battery charger and power supply capable of
providing power to the most demanding of applications.

Ease of Installation
The elegant and simple construction of the panel enables the chassis to be completely dismantled by
removing just two screws. The outer cover can also be detached by removing two hinge pins making first
fix installation very simple and enabling the sensitive electronic parts to be stored safely for re-fitting at the
commissioning stage. Sigma Sounder - Sounder Controller Units See DS48

31
 Sigma Matrix Conventional Fire Alarm Sigma Matrix Features
Mimic Display System Up to 320 LED’s can be controlled

Full colour printing

Available in a range of standard enclosures to

suit any application

Bespoke sized units can be made upon request

Choice of Red, Green or Yellow LED’s

Available with or without controls

Same look and feel as Sigma range

Sigma Matrix can easily be upgraded on site

with minimal cost and effort

EN54-4 approved PSU (optional)

32
Sigma Matrix Overview Standard Enclosure Size Options

Conventional Fire Detection

Sigma Matrix is an innovative fire alarm mimic system which can be connected to any system providing volt
free contacts or a switched 24V DC supply.

The Sigma Matrix system uses flexible, fibre optic light guides to illuminate areas on a floor plan, laid over
a high resolution grid. This unique system dispenses completely with wiring and enables indicators to be
moved, removed or added on site without the need for any wiring.
185
303
Sigma Matrix can be supplied with or without common LEDs and controls. Optional LEDs indicate Power on,
Fire, Fault and Disablement and optional controls are for Alarm silence, Buzzer silence, Lamp test and Reset.

Housed in attractive, slimline enclosures to match and with high quality, full colour or monochrome floor
M2 385mm W x 310mm H x 90mm D
plans, Sigma Matrix provides a clear, geographical indication of fire alarm or other system activation enabling
speedy identification of the source of an alarm or other event.

Future Proofing
The Sigma Matrix is ideal for buildings such as hospitals where the building layout may evolve over a period
of time. 225
400

As the building changes, so too can Sigma Matrix, with very little cost or disruption. Modifying the mimic
is very straightforward and can be carried out on site without the need for any wiring or special tools. The
positions of the indicators can be freely moved anywhere on the grid and new indicators can be added using
kits of lenses and light pipes which are available. Additional mimic PCB’s are also available in kit form to S3 500mm W x 355mm H x 117mm D
enable the capacity of the mimic to be increased as required.

Custom Solutions
Where the requirements of the installation exceed the standard range of Sigma Matrix panels, completely 400
303
bespoke solutions are available.

The enclosure size, mimic viewing area, colour and finish can all be tailored for the individual requirements of
the site, including the option of surface or flush construction.

M3 385mm W x 520mm H x 110mm D

515
400

S4 500mm W x 650mm H x 137mm D 33

Sigma CP Network Diagram

2 Core Power - 24V DC

Sounder 2

2 Core Data - RS485

Sounder 1

Zone 2

Zone 1 Sigma CP - EN54-2/4

Approved Control Unit

230V AC

34
 Conventional Fire Detection
Ancillary Board Ancillary Board
Sigma CP-R
Repeater Panel

230V AC

Sigma CP-R
Plant Controls Repeater Panel
Sigma Matrix
Fire Alarm Mimic
Display System

24V PSU Sounder Board

35
18
 Sigma XT Extinguishant Control Panel Sigma XT Features
Approved to EN12094-1, EN54-2 and EN54-4

Three detection zones as standard

Any single zone or any combinations of zones can be

configured to release

Configurable first stage sounder delays

Configurable detection delays

Zero time delay upon manual release option

Compatible with I.S. barriers

Non-latching zone input option to receive signals from

other systems such as aspirating equipment

Configurable extinguishant delays up to 60 seconds

in 5 second steps

Configurable extinguishant duration up to 5 minutes

in 5 second steps

Countdown timer shows time remaining until release

Supports up to seven, four wire status indicators

Built in Extract Fan control

36
Sigma XT Overview Compatible Equipment & Extras

Extinguishant System Control

Designed and manufactured to the highest standards in a quality controlled environment, the Sigma XT
extinguishant releasing panel offers outstanding value and performance for all small to medium fixed
firefighting installations.

With three detection zones as standard, extinguishant release can be configured to activate from any
combination of detection zone inputs to allow (among other combinations) any two from three type
activations such as would be required for detection in ceiling void, room and floor void applications.

The extensive configuration options of the Sigma XT allow the functionality of the system to be extensively
modified while still complying with the requirements of the controlling standards for the equipment.
Sigma Si Status Units See DS41
The panel contains a large LED display to enable easy configuration and control which also displays the time
remaining until extinguishant release for added user safety.

The countdown timer is duplicated on up to seven remote status units to provide local indication of the
extinguishant system status. With all of the electronics mounted on a single, easily removable, steel plate
Sigma XT panels are both robust and easy to install.

Connectivity
To compliment the Sigma XT control panel there is a range of system status units.

Up to seven status units can be connected on a serial bus and require just two cores for data and two cores Sigma Si Hold Off Switch See DS41
for power. Once connected, status units are supervised and the Sigma XT control panel will indicate a fault
condition should any unit become disconnected.

Ease of Installation
The elegant and simple construction of the panel enables the chassis to be completely dismantled by
removing just two screws. The outer cover can also be detached by removing two hinge pins making first
fix installation very simple and enabling the sensitive electronic parts to be stored safely for re-fitting at the
commissioning stage.

Sigma Si Ancillary PCB See DS75

37
 Sigma XT+ Extinguishant Control Panel Sigma XT+ Features
Multi-Area Approved to EN12094-1, EN54-2 and EN54-4

2, 4 or 8 detection zones

1 to 4 extinguishant areas

Dual extinguishant outputs for each area

(configurable as Main/Reserve)

First and second stage sounder outputs for each area

First and second stage volt free changeover contacts

for each area

Released volt free contact per area

Fault volt free contact per area

Programmable extinguishant delays

Programmable output duration

Extract fan control

Countdown indicator shows time until release in seconds

Mode select and manual release controls per area

Monitored remote manual release input

Monitored remote Hold input

Monitored remote Mode select (door interlock) input

Monitored remote Released pressure switch input

Monitored remote Low Pressure switch input

Monitored Abort input

Serial connection for Sigma Si status units and

ancillary boards. (K588)

38
Sigma XT+ Overview Compatible Equipment & Extras

Extinguishant System Control

The Sigma XT+ range combines feature rich, Sigma CP conventional fire detection from two to eight
zones with highly configurable extinguishing control modules to provide an integrated control solution for
extinguishing systems with up to four protected areas.

The fire detection section connects to the extinguishant control modules via a serial link which allows secure,
bi-directional transfer of data between the two. Sigma XT+ modules may be mounted remotely in separate
enclosures and connected to Sigma CP panels via this serial interface to provide central fire detection and
control with distributed extinguishing systems.

Sigma XT+ modules may also be mounted separately from fire detection and control equipment and
activated by addressable output modules or volt free contacts from other systems via two monitored
activation inputs. Sigma Si Status Units See DS41

The fire detection part of the system has all of the benefits of the popular Sigma CP range with its many,
easily accessed configuration options and compatibility with a wide range of detection devices.

The Sigma XT+ extinguishing modules set a new benchmark for extinguishing control panels. Each module
is controlled by its own powerful microcontroller bringing unparalleled intelligence and versatility to multi area
extinguishing systems for the first time.

Sigma XT+ modules have inputs and outputs to cover all system requirements including individual, monitored
first and second stage alarms and dual extinguishing outputs. The extinguishing outputs can be configured
to operate together or as main and reserve for essential back up following a discharge. They can also be
individually calibrated to provide true open and short circuit monitoring through pyrotechnic actuators or a Sigma Si Hold Off Switch See DS41
wide range of solenoids.

Connectivity
In addition to Sigma XT+ extinguishing modules, up to seven Sigma CP ancillary boards providing zonal and
common relay outputs and seven Sigma CP sounder boards, each providing an additional eight, monitored
sounder circuits can be connected to the Sigma CP RS485 serial bus at up to 1200 metres from the control
equipment.

Also, up to seven Sigma XT ancillary boards and seven Sigma Si status units can be connected to each
Sigma XT+ module to provide remote status indication, control and additional outputs as required at up to
1200 metres from the control equipment. This flexibility ensures that any system configuration can be realised Sigma Si Ancillary PCB See DS75
with a minimum of cabling.

Ease of Installation
The simple construction of Sigma XT+ control panels utilises removable bridge plates for mounting all
electronic assemblies. These bridge plates bring the terminals to the front of the enclosure providing easy
access to all wiring terminals.

The outer door may be removed to further improve access by withdrawing the easily accessible hinge pins.
This ensures clear access for wiring and protection of the electronic assemblies during installation.

Multiple knockouts in the top, bottom and back and sides of the enclosures provide ample options for cable
entries. 39
 Sigma Si Extinguishant Status & Ancillary Units

40
Sigma Si Features Sigma Si Overview Hold Off Overview

Extinguishant System Control

Approved to EN12094-1, EN54-2 and EN54-4 Sigma Si is range of system status indicator units Sigma Si Hold off units are available with red or
for use with Kentec Sigma XT and Sigma XT+ green actuators (BS 7273-1 recommends white
2, 4 or 8 detection zones extinguishant releasing control panels. with red button) and are mounted in a single gang,
Certified compliant with BS EN12094-1 when used surface mounting enclosure. For flush mounting, the
The Sigma Si range of status indicators provide
with Sigma XT control equipment enclosure may be discarded and the unit mounted to
detailed status information for Sigma XT and Sigma
High brightness LEDs XT+ extinguishant release control equipment. a standard UK single gang electrical back box..

Detailed indication of the status of the control panel All models provide high brightness, LED indication of The unit has a durable, shrouded push button to
Manual Only, Automatic and Manual, Hold operated, prevent accidental operation and a simple 2 wire
Monitored data connection Disabled, Imminent and Released conditions. Models connection to Sigma XT, Sigma XT+ or Sigma Si
are also available with zonal fire indicators and a status units is required.
Countdown timer shows time remaining until release
common fault indicator.
Manual only and Automatic & Manual mode Sigma Si Hold off units are fitted with normally open
select keyswitch option For systems where local control of the Automatic/ and normally closed contacts to allow operation with
Manual mode and or a Manual extinguishant release monitored and unmonitored systems
Four wire connection (data and power) control are required, units are available with these

Protected dual action manual release switch option

controls fitted.
Ancillary PCB Overview
All models have monitored inputs for the remote
Option for zonal fire and common fault indication The Sigma XT Ancillary PCB is compatible with Sigma
with buzzer connection of Automatic/ Manual mode and Hold
switches and are provided with a large, LED display XT and Sigma XT+ control panels.
Robust, high quality enclosure which shows a countdown of the time remaining until
The board provides volt free normally open contacts
the extinguishant is released in seconds.
Easy access to terminals allowing control of sub-systems and plant remotely
from the main panel over a two wire data bus.
Remote Auto/Manual door interlock input (monitored)
Mains powered, boxed Ancillary boards require only a
Remote Hold input (monitored)
two core data cable from the main control panel.
Internal fault diagnosis indicators
24V DC versions require an additional two cores for
Weatherproof IP65 versions available power either from the main panel or from another 24V
DC source.
Internal buzzer
Up to 7 Ancillary boards can be connected to a control
panel and each is allocated an address from 1 to 7 us-
Ancillary PCB Features ing a binary coded DIL switch. The total length of the
data cable from the main panel to the last repeater can
Two wire serial connection
be up to 1200 metres.
Up to 7 per system
A mixture of status units and Ancillary boards, up to a
230V AC or 24V DC powered versions maximum of 7 of each type, can be connected to the
serial data bus.
Volt free relay outputs for fire and extinguishing system status

Relay operated LED indicators

41
 Syncro XT+ Extinguishant Control Panel Syncro XT+ Features
Multi-Area Addressable Complies with EN12094-1, EN54-2 and EN54-4

16 detection zones
ING
COM ON Up to 4 extinguishant areas
SO
Dual extinguishant outputs for each area
(configurable as Main/Reserve)

First and second stage sounder outputs for each area

First and second stage volt free changeover

contacts for each area

Released volt free contact per area

Fault volt free contact per area

Programmable extinguishant delays

Programmable output duration

Countdown indicator shows time until release

in seconds

Mode select and manual release controls per area

Monitored remote manual release input

Monitored remote hold input

Monitored remote mode select (door interlock) input

Monitored remote released pressure switch input

Monitored Abort input

Serial connections for Sigma Si status units and

ancillary boards. (K588)

42
Syncro XT+ Overview Compatible Equipment & Extras

Extinguishant System Control

Syncro XT+ control panels are multi-area extinguishant control panels complying with EN12094-1, EN54-2
and EN54-4.

Up to 16 zones of addressable detection over 1 or 2 loops ensure every detector is able to contribute to
extinguishant release.

Up to 4 extinguishing areas and 2 releasing outputs per area can be controlled via simple coincidence
detection or via more complex cause and effects configured by the Loop Explorer configuration programme.

Syncro XT+ allows extinguishing systems to take full advantage of the more sophisticated detection
techniques provided by modern fire detectors as well as the other benefits of analogue addressable systems
Sigma Si Status Units See DS41
such as control of loop connected sounders, beacons and input/output modules.

With the addition of a Syncro network card, Syncro XT+ control panels can be networked to provide scalable
extinguishing systems for all sizes of installation.

Stand alone extinguishant control units are also available with 2 monitored inputs to receive initiating signals
from remote fire detection control panels or addressable modules.

Each extinguishant area has a comprehensive set of inputs and outputs and is configurable via the Loop
Explorer Configuration Programme.

All extinguishant areas may have up to 7, serially connected Sigma Si status indication and control units or
Syncro Si Status Units See DS79
ancillary relay boards connected via a simple 4 core cable.

43
Sigma XT Network Diagram

Manual Release

Hold Off Unit

Door Interlock

2nd Stage Sounders

1st Stage Sounders

Detection Zone 3

Detection Zone 2

Detection Zone 1

Sigma XT - EN12094-1
Approved Control Unit

44
 Extinguishant System Control
Addressable
House Fire Alarm

Released Pressure Switch

Ancillary Board Status Unit Status Unit Status Unit

Activate Extinguisher
Low Pressure Switch

4 Core
Hold Off Unit BMS
Interface
2 Core
2 Core
Door Interlock

4 Core (FP200 max. length 1200m)

Status Unit Ancillary Board

45
18
 PSU Power Supplies

S408 S406 S2014

46
K25000 Power supplies Overview Power Supply Units

Power Supplies
The K25000 range of 24V DC power supplies are designed to meet the exacting requirements of fire detection
and alarm systems and fire protection systems.

All models charge sealed lead acid batteries using sophisticated, temperature compensated charging and
monitoring techniques to keep the batteries in the best possible condition.

Over depletion of batteries is prevented by a low battery voltage disconnection function which removes the load
from the batteries when their terminal voltage reduces to a level which would damage them.

A low battery voltage fault warning is given when the batteries reach the minimum terminal voltage recommended
by the battery manufacturers.

A high series resistance in the battery supply circuit which would allow the power supply output voltage to fall S2014 - 2.5A PSU See DS19
outside of the specified range is indicated as a fault condition.

K25000 power supplies can be fitted with an optional dual output board to provide redundant power paths for fire
alarm applications and are available in a range of enclosures to accommodate different battery sizes.

Onboard LED indicators are provided to indicate the status of the unit and an onboard header is available to
extend status signals to other systems volt free relay contact that operates upon any fault condition or total
power failure.

Enclosures are designed to match both Sigma and Syncro fire panel ranges and are constructed from 1.2mm mild
steel and are finished with epoxy powder coating.

The K25000 boxed range is available in the following power outputs:

S406 - 5.25A PSU See DS19
K25250 range – 2.5A output and up to 12Ah batteries

K25400 range - 5.25A output and up to 26Ah batteries

K25800 range – 10.25A output and up to 45Ah batteries

Unboxed or caged power supplies for incorporation into other equipment are available as follows:

S2014 – 2.5A output

S406- 5.25A output

S408 – 10.25A output

S408 - 10.25A PSU See DS67

47
 Miscellaneous Items

Warning Signs Remote DocBox Audio Visual 1 Way Remote 4 Way Tamper Resistant
Indicator Unit Relay Board Indicator Unit Relay Board Vision Window

48
Warning Signs Relay Boards

Miscellaneous Items
Powered by a nominal 24V DC supply, the illuminated warning signs employ the very latest in Easy to fit and wire for additional control functions or to expand the capability of existing relay
LED technology to provide a high reliability, high brightness, audio/ visual warning indication unit to outputs, these simple boards contains either one or four 24V DC relays, which can be used for
supplement mandatory alarm warnings. any extra low voltage switching applications.

The brightness of the sign remains constant over its entire operating range of 15 to 30 volts DC due Each relay has two changeover contacts, and an LED indicator to show when the coil is
to the unique “power boost” circuitry employed. This ensures that even with a system running on energised.
depleted batteries, all signs remain at full intensity.
The coils of the relays are commoned to the positive supply and the relays can be operated
A range of standard text signs are available and fully customised text and languages are easily individually by switching a negative to the numbered coil inputs.
accommodated. The large display panel is backlight with high intensity white LEDs to provide a high
The contacts are suitable for switching a maximum of 30V DC and 2 Amps. The current
contrast indication in a range of different colours.
consumption of the unit when operated from a 24V supply is approximately 25mA per relay.
A split level function allows the top and bottom halves of the sign to be illuminated independently via
separate inputs or by reversing the supply voltage allowing two stage messages to be displayed if
required.

The internal buzzer can be enabled or disabled via configuration switches and it can be silenced via a
two wire remote input.

The enclosure is slimline and attractively finished in a durable, neutral epoxy powder coat.

Tamper Vision Resistant Window Audio Visual

The Tamper Resistant Vision Window is perfect for public areas where restricted access is A range of indicator units with either red or yellow indicators to provide audible and visual status
necessary to prevent damage and unauthorised operation of the control panel. The cover features a of alarms, isolations or other functions.
fully welded steel construction and key lockable inner door making it robust and secure.
These units are available with a keyswitch to silence the internal buzzer or a keyswitch to
The Vision Window is available from stock, fully assembled, and can be fitted on site in minutes by illuminate the indicator and buzzer. A volt free contact is provided when the keyswitch is operated
simply taking out the hinge pins on the existing enclosure and removing the lid before fitting the new for ancillary control functions.
Vision Window cover and hinge pins.
The units are mounted in a durable steel enclosure that has the same plate fixing centres as a
Control panels can also be supplied pre-fitted with the Vision Window on any M2, H2, M3, and H3 standard UK single gang electrical box allowing the unit to be easily flush mounted if required.
size control panels.

Sigma DocBox Remote Indicator Unit

Designed to provide a convenient method of storing system test records, manuals, configuration Remote indicator units provide an extension for LED indicators on hidden detection devices to
files, keys and other documents or access arrangements for fire alarm and protection systems, allow their status to be observed without having to expose the detection device itself.
the Sigma DocBox is finished and constructed in a similar manner to Sigma and Syncro fire alarm
All units have dual, high brightness LED indicators with a wide viewing angle that flash alternately
control equipment.
to attract attention and are available mounted to square or round metal plates for fitting to
Available as standard, deep or extra deep versions, DocBoxes are available to suit any size of standard electrical back boxes. They are finished in white, durable epoxy powder and printed in
installation. red with “FIRE ALARM IN CONCEALED SPACE”. Other printing options are available upon
request.
The DocBox also doubles up as a Key Box providing 7 easily accessible formed key hooks inside
the enclosure and is itself lockable using a standard fire control panel key. Remote indicators are compatible with all types of conventional and addressable detectors.
49
 Elite Analogue Addressable Fire Control Panels & Repeaters
UL/ FM Approved

eMatrix eView Elite RS Elite

50
Elite Elite RS

UL/FM Approved Panels

The Elite analogue addressable fire alarm control panel supports 2 or 4 SLC loops for Elite RS is a versatile range of open protocol fire alarm control panels compatible with
a total of 500 primary points or 800 points using subpoints. existing Elite fire alarm panel technology.

SLC loop communications uses standard twisted pair cabling, shielded cable is not Available with one or two detection loops capable of hosting up to 600 devices.
necessary.
Elite RS uses leading edge microprocessor based electronics to provide a flexible
The panel may be configured with various communication cards; Communications control system with high reliability and integrity.
options support central station monitoring, Virtual Panel, and networking.
Suitable for all small to medium sized fire detection systems, Elite RS control panels
The Panel can be configured as a stand alone panel with just a few devices for a can be expanded and networked to become part of much larger systems if the need
small building, it can also operate as the building system and can be part of a network arises, therefore providing a future proof solution for any installation.
with a total of 64 nodes serving a multiple building campus or a very large facility.
With its large graphical display and ergonomic button and indicator layout, the
Auto Learn capability provides a convenient method to troubleshoot new Elite RS control panel is simple and straightforward to understand for installers,
installations before final programming is loaded. commissioning engineers and end users alike.

eMatrix eView
The eMatrix system uses flexible, optic light guides to illuminate areas on a floor plan, Designed and manufactured to the highest standards in a quality controlled
laid over a high resolution grid. This unique system dispenses completely with wiring environment the eView fire alarm annunciator provides a simple and convenient
and enables indicators to be moved, removed or added on site without the need for method of extending the controls and indications of the Elite fire alarm control panel
any wiring. to other locations.

All indicators can be configured to operate upon any event type and at point, zone The large, graphic liquid crystal display and high brightness LED indicators duplicate
or group level via the powerful and intuitive Loop Explorer configuration or ESP the indications on the Elite fire alarm control panel at up to 15 additional locations via a
Discovery. eMatrix can be supplied with or without LEDs and controls. Optional LEDs simple, two-wire serial data connection.
indicate Power on, Fire, Trouble and Disablement and optional controls are for Alarm
silence, Buzzer silence, Lamp test and Reset. The eView is powered by 24V DC (which can be via an additional 2 conductors from
the control panel or local 24V DC listed supply).
Housed in attractive, slimline enclosures to match Elite fire alarm panels and with high
quality, full colour or monochrome floor plans, eMatrix provides a clear, geographical eView is housed in a small enclosure which is styled similarly to the Elite control panel
indication of fire alarm activation enabling speedy identification of the source of an and is ideal for installations where a large control panel would be detrimental to décor
alarm. such as entrance halls.

Up to 15 eView annunciators can be connected to each control panel on the Elite

network making eView ideal where multiple points of indication and/ or control are
required such as nurses stations or shop units.

51
 Sigma A-CP Conventional Control Panel Sigma A-CP Features
UL Approved UL864 approved

Two, four or eight initiating circuits

Initiating circuits individually configurable as Fire, Water

flow or Supervisory

Two 2A notification appliance circuits

Selectable NAC sync protocols

Two 2.0A notification appliance circuits

6.5A power supply

Alarm verification selectable by zone

Resettable Aux power output rated at 0.3A

Aux power configurable to power off on Fire condition

Fire, Trouble and Supervisory relays

Single person walk test function

Optional DACT

Many advanced configuration options

72 hour standby with 7Ah batteries

Compact enclosure

52
Sigma A-CP Overview Compatible Equipment & Extras

UL/FM Approved Panels

The Sigma A-CP is a range of conventional fire control panels with optional built in communicator.

With 2, 4 or 8 initiating circuits all panels can be extensively configured via a simple front panel operated
programming method.

The low standby power requirements and cost effective small batteries allow the panel to be mounted in
a small discrete enclosure which is available in standard red or optionally in an attractive grey colour.

A simple programming method using just 3 front panel buttons allows an extensive list of configuration
options to be set and reviewed.

Single board construction which allows easy removal of all electronic parts by removing just 2 screws Sigma A-CP Ancillary Board See DS78
and ample provision of cable entry knockouts simplify installation.

4 Amp notification appliance power and built in selectable sync protocols provide ample power and
control for a wide range of standard notification appliances.

The built in RS485 communications bus provides the facility to connect 4 wire annunciators or ancillary
relay boards to provide further indication and control options throughout a premises.

The optional DACT allows dual line reporting to central stations and provides a 500 event history buffer.

53
 Sigma A-XT Extinguishant Control Panel Sigma A-XT Features
UL/ FM Approved UL864 and FM listed

Three initiation circuits as standard

Any single zone or any combinations of zones can be

configured to release

Configurable first stage NAC delays

Configurable detection delays

Zero time delay upon manual release option

Compatible with I.S. barriers

Non-latching zone input option to receive signals from

other systems such as aspirating equipment

Configurable releasing delays up to 60 seconds

in 5 second steps

Configurable releasing duration up to 5 minutes

in 5 second steps

Countdown timer shows time remaining until release

Supports up to seven, four wire status indicators

Built in Extract Fan control

54
Sigma A-XT Overview Compatible Equipment & Extras

UL/FM Approved Panels

Designed and manufactured to the highest standards in a quality controlled environment and with UL and FM
approvals, the Sigma A-XT releasing panel offers outstanding value and performance for all small to medium
fixed firefighting installations.

With three initiation circuits as standard, release can be configured to activate from any combination of
detection zone inputs to allow (among other combinations) any two from three type activations such as
would be required for detection in ceiling void, room and floor void applications.

The extensive configuration options of the Sigma A-XT allow the functionality of the system to be
extensively modified.
Sigma A-Si Status Units See DS73
The panel contains a large LED display to enable easy configuration and control which also displays the time
remaining until release for added user safety.

The countdown timer is duplicated on up to seven remote status units to provide local indication of the
system status.

With all of the electronics mounted on a single, easily removable, steel plate Sigma A-XT panels are both
robust and easy to install.

Sigma A-XT is supplied in an enclosure that matches the design and colour of the Elite RS range and is
available in standard red or optional grey.
Sigma A-Si Hold Off Switch See DS73

Sigma A-Si Ancillary PCB See DS74

55
 Sigma A-Si Extinguishant Status & Ancillary Units
UL/ FM Approved

Not UL/FM Not UL/FM Not UL/FM

Approved Approved Approved

56
Sigma A-Si Features Sigma A-Si Overview Hold Off Overview

UL/FM Approved Panels

UL864 and FM listed The Sigma A-Si range of status indicators provide The Sigma A-Si Abort switch connects to the Abort
detailed status information for Sigma A-XT releasing terminals of the Sigma A-XT releasing panel. Any
High brightness LEDs
control equipment. number of Sigma A-Si Abort switches may be
connected to the circuit.
Detailed indication of the status of the control panel All models provide high brightness, LED indication of
Manual Only, Automatic and Manual, Abort operated, The last switch must have the end of line device from
Supervised data connection
Disabled, Imminent and Released conditions. Models the Abort circuit terminals of the Sigma A-XT releasing
Countdown timer shows time remaining until release are also available with zonal fire indicators and a panel fitted across its connections to provide open
common trouble indicator. and short circuit supervision.
Manual only and Automatic & Manual mode select
keyswitch option For systems where local control of the Automatic/ The unit is supplied mounted to a rugged steel
Manual mode and or a Manual extinguishant release enclosure but may also be flush mounted to a single
Four wire connection (data and power)
control are required, units are available with these gang electrical box.
controls fitted.
Protected dual action manual release switch option
Ancillary PCB Overview
All models have supervised inputs for the remote
Option for zonal fire and trouble indication with buzzer
connection of Automatic/ Manual mode and abort The Sigma A-XT Ancillary Board is compatible with all
Robust, high quality enclosure switches. Sigma A-XT control panels.

Easy access to terminals All units contain a large, LED display which shows The board provides volt free normally open contacts
a countdown of the time remaining until release in allowing control of sub-systems and plant remotely
Remote Auto/Manual door interlock input (supervised) seconds. from the main panel over a two wire data bus.

Remote Abort input (supervised)

Connectivity Ancillary boards require only a two core data cable
from the main control panel and a two core power
Internal trouble diagnosis indicators
Up to seven Sigma A-SI status units can be cable from the main panel.
connected to the Sigma A-XT serial bus and require
Up to 7 Ancillary boards can be connected to a control
just two cores for data and two cores for power.
Ancillary PCB Features Once connected, status units are supervised and the
panel and each is allocated an address from 1 to 7
using a binary coded DIL switch. The total length of
UL864 and FM listed Sigma A-XT control panel will indicate a fault condition
the data cable from the main panel to the last repeater
should any unit become disconnected.
Two wire serial connection must not exceed 4000 feet.

Up to 7 per system A mixture of status units and Ancillary boards, up to a

maximum of 7 of each type, can be connected to the
Volt free relay outputs for fire and releasing system status serial data bus.

Relay operated LED indicators

57
 Syncro ASM Marine & Offshore Analogue Addressable Syncro ASM Features
1-2 Loop Control Panel 16 zonal LED indicators

2 programmable sounder circuits

5 programmable inputs

3 programmable relays

3A power supply

Large graphic display

Real time clock

Powerful, network wide cause and effects

Sensitivity adjustment and Drift Compensation

Apollo and Hochiki protocol

Same look and feel as Syncro range

Stores 1000 last events in event log

Compact, stylish enclosure

Installer friendly, removable equipment chassis

Different language and character set variants available

Fully EN54-2 and EN54-4 compliant

58
Syncro ASM Overview Compatible Equipment & Extras

Marine Fire Detection

Based upon the popular Syncro AS single and two loop analogue addressable fire control panel, the
Syncro ASM is certified with a host of classification societies and is Marine Equipment Directive approved.

Compatible with marine approved devices manufactured by Apollo Fire Detectors and Hochiki, Syncro
ASM provides a cost effective and scalable solution for all marine fire alarm systems.

Up to 64 Syncro ASM control panels may be networked to provide integrated control and indication of
over 16000 fire alarm points.

The optional Voyage Data Recorder interface outputs standard NMEA 0183 protocol and can be fitted
inside any control panel on the network.
Apollo Detectors & Devices See Kentec website
Suitable for all small to medium sized vessels, Syncro ASM control panels can be expanded and
networked to become part of much larger systems if the need arises, therefore providing a future proof
solution for any vessel.

With its large graphical display and ergonomic button and indicator layout, the Syncro ASM control panel is
simple and straightforward to understand for installers, commissioning engineers and end users alike.

Hochiki Detectors & Devices See Kentec website

Syncro View Marine See DS69

59
 Custom Custom Engineered Solutions Facilties
Expert design advice

Mechanical engineering design

Artwork and printing design

Documentation

Electrical engineering

Electronic engineering

Sheet metal fabrication

Powder coat finishing

Metal finishing

Silk screen printing

Wire looming

Electrical safety testing

Technical support

60
 Custom Engineered Solutions
From the initial One of the key areas of our business is the design
design process and manufacture of bespoke equipment. Kentec
has considerable expertise in this field with over
25 years experience, so you can be certain that all
To sheet metal
fabrication custom engineered product will be designed and built
in accordance with your exact requirements and our
strict ISO 9001 approved quality procedures.

All custom built equipment is project managed by our

engineering department, using the latest software
to produce electrical, mechanical and construction
drawings to the customers specifications.

We have a dedicated area for the construction of

bespoke product and this was enlarged in the first
quarter of 2011 to allow us to increase our capacity
and offer better service to our customers including
factory acceptance testing.

Our skilled and dedicated production engineers build

each bespoke product to very high standards and to
specifications driven by our customers.

We have full control at every stage allowing us to

To painting
offer industry leading delivery times and with quality
and printing
you can have confidence in.
To panel
construction

61
 Custom Custom Engineered Solutions Applications
Smoke Damper Control Panels

Composite Relay Units

(c/w Resettable Latching Relay & Firemans Switch)

Sprinkler System Indicator Panels

Pump Status Indicator Panels

Firemans Control Switch Panels

Analogue/Addressable Interface Units (with or without

integral PSU)

Mimic Repeat Indicator Panels (perspex/metal, metal

only, black & white or multi-coloured)

62
 Custom Engineered Solutions
Choose your
Finish

Choose your
Colour

Choose your
Specification

63
 Kentec Electronics Ltd.

Kentec Electronics Ltd

Units 25-27 Fawkes Avenue Questor
Dartford Kent DA1 1JQ England
Tel: +44 (0)1322 222121
Fax: +44 (0)1322 291794
MANAGEMENT
SYSTEMS
E-mail: sales@kentec.co.uk
Certificate No. FM 32987
BS EN ISO 9001: 2008
Certificate No. EMS 518118
BS EN ISO 14001:2004
Certificate No.360
BS EN ISO 9001:2008
KM 73505
KM 96761 Web: www.kentec.co.uk V1.02