INSTRUCTION MANUAL

VHF TRANSCEIVER
iF3161/iF3163
Series
UHF TRANSCEIVER
iF4161/iF4163
Series
iF4167DT

This device complies with Part 15 of the FCC Rules. Op-

eration is subject to the condition that this device does not
cause harmful interference.

The photo shows the

UHF transceiver.
 IMPORTANT EXPLICIT DEFINITIONS
READ ALL INSTRUCTIONS carefully and com- WORD DEFINITION
pletely before using the transceiver.
Personal death, serious injury or an explo-
RDANGER!
SAVE THIS INSTRUCTION MANUAL — This sion may occur.
instruction manual contains important oper­ating instructions Personal injury, fire hazard or electric
for the IC-F3161T, IC-F3161S, IC-F3161DT, IC-F3161DS, RWARNING!
shock may occur.
IC-F3163T and IC-F3163S VHF TRANSCEIVERS and Equipment damage may occur.
CAUTION
IC-F4161T, IC-F4161S, IC-F4161DT, IC-F4161DS, IC-
F4163T, IC-F4163S and IC-F4167DT UHF TRANSCEIV- If disregarded, inconvenience only. No risk
NOTE of personal injury, fire or electric shock.
ERS.

See the operating guide for details of IDAS™, BIIS, MDC

and LTR® system operations. Ask your dealer for details.

This instruction manual includes some functions which are

usable only when they are preprogrammed by your dealer.
Ask your dealer for details.

Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incor-
porated (Japan) in Japan, the United States, the United Kingdom, Germany,
France, Spain, Russia, Australia, New Zealand and/or other countries.
IDAS is trademark of Icom Incorporated (Japan).
LTR is a registered trademark of the E.F.Johnson Technologies, INC. in the
United States.
All other products or brands are registered trademarks or trademarks of their
respective holders.
i
PRECAUTIONS 1
2
R DANGER! NEVER short terminals of the battery pack. DO NOT push [PTT] when you do not actually intend to transmit. 3
Also, current may flow into nearby metal objects such as a key, so
be careful when placing the battery packs (or the transceiver) in DO NOT modify the transceiver. The specifications may change
handbags, etc. Simply carrying with or placing near metal objects and then not comply with the requirements of a corresponded regu- 4
lation. The transceiver warranty does not cover any problems caused
such as a key, etc. may cause shorting. This may damage not only
by unauthorized modification.
5
the battery pack, but also the transceiver.
R DANGER! Use and charge only specified Icom battery packs DO NOT operate or place the transceiver in direct sunlight or 6
with Icom transceivers or Icom chargers. Only Icom battery packs in areas with temperatures below +22°F (–30°C) or above +140°F
are tested and approved for use with Icom transceivers or charged (+60°C).
7
with Icom chargers. Using third-party or counterfeit battery packs or
chargers may cause smoke, fire, or cause the battery to burst. DO NOT operate the transceiver near unshielded electrical blast- 8
ing caps or in an explosive atmosphere. 9
R WARNING! NEVER hold the transceiver so that the an-
tenna is very close to, or touching exposed parts of the body, es- DO NOT use harsh solvents such as benzine or alcohol when
pecially the face or eyes, while transmitting. The transceiver will cleaning, as they will damage the transceiver surfaces. 10
perform best if the microphone is 2 to 4 in. (5 to 10 cm) away from
the lips and the transceiver is vertical. BE CAREFUL! The transceiver will become hot when operating 11
it continuously for long periods of time.
R WARNING! NEVER operate the transceiver with a head- 12
set or other audio accessories at high volume levels. The continu- KEEP the transceiver away from the heavy rain, and Never im-
ous high volume operation may cause a ringing in your ears. If you merse it in the water. The transceiver meets IP55* requirements for 13
experience the ringing, reduce the volume level or discontinue use. dust-protection and water jet resistance.
CAUTION: NEVER operate the transceiver while driving a ve- 14
However, once the transceiver has been dropped, dust-protection
hicle. Safe driving requires your full attention—anything less may and water jet resistance cannot be guaranteed due to the fact that 15
result in an accident.
the transceiver may be cracked, or the waterproof seal damaged, etc.
CAUTION: MAKE SURE the flexible antenna, battery pack 16
and jack cover are securely attached to the transceiver, and that * Only when the supplied battery pack, flexible antenna and con-
the antenna and battery pack are dry before attachment. Expos- nector cover are attached.
ing the inside of the transceiver to dust or water will result in
serious damage to the transceiver.

ii
 VOICE CODING TECHNOLOGY FCC INFORMATION
The AMBE+2™ voice coding Technology embodied in this • FOR CLASS A UNINTENTIONAL RADIATORS:
product is protected by intellectual property rights including This equipment has been tested and found to comply with the
patent rights, copyrights and trade secrets of Digital Voice limits for a Class A digital device, pursuant to part 15 of the
Systems, Inc. This voice coding Technology is licensed solely FCC Rules. These limits are designed to provide reasonable
for use within this Communications Equipment. The user of protection against harmful interference when the equipment is
this Technology is explicitly prohibited from attempting to ex- operated in a commercial environment. This equipment gener-
tract, remove, decompile, reverse engineer, or disassemble ates, uses, and can radiate radio frequency energy and, if not
the Object Code, or in any other way convert the Object Code installed and used in accordance with the instruction manual,
into a human-readable form. U.S. Patent Nos. may cause harmful interference to radio communications.
#5,870,405, #5,826,222, #5,754,974, #5,701,390, #5,715,365, Operation of this equipment in a residential area is likely to
#5,649,050, #5,630,011, #5,581,656, #5,517,511, #5,491,772, cause harmful interference in which case the user will be re-
#5,247,579, #5,226,084 and #5,195,166. quired to correct the interference at his own expense.

CAUTION: Changes or modifications to this transceiver, not ex-

pressly approved by Icom Inc., could void your authority to oper-
ate this transceiver under FCC regulations.

iii
TABLE OF CONTENTS 1
2
IMPORTANT........................................................................... i 4 BATTERY CHARGING.............................................19−23
3
EXPLICIT DEFINITIONS........................................................ i ■ Caution........................................................................19
PRECAUTIONS..................................................................... ii ■ Optional battery chargers............................................21 4
VOICE CODING TECHNOLOGY......................................... iii 5 BATTERY CASE.............................................................24 5
FCC INFORMATION............................................................ iii ■ Optional battery case (BP-240)...................................24
6
1 ACCESSORIES............................................................1−3 6 SWIVEL BELT CLIP.................................................25−26
■ Supplied accessories....................................................1 ■ MB-93 contents...........................................................25 7
■ Accessory attachments.................................................1 ■ To attach......................................................................25 8
2 PANEL DESCRIPTION...............................................4−10 ■ To detach.....................................................................26
9
■ Front panel....................................................................4 7 SPEAKER MICROPHONE.............................................27
■ Function display............................................................5 ■ Optional HM-169/HM-170GP description.....................27 10
■ Programmable function keys.........................................6 ■ To attach......................................................................27 11
3 BASIC OPERATION.................................................11−18 8 OPTIONS..................................................................28−31
■ Turning power ON.......................................................11
12
9 SAFETY TRAINING INFORMATION........................32−34
■ Channel selection........................................................12 13
■ Call procedure.............................................................13 14
■ Receiving and transmitting..........................................13
■ User set mode.............................................................16 15
■ Scrambler function......................................................16 16
■ Stun function...............................................................16
■ Emergency transmission.............................................17
■ Man Down Emergency Call.........................................17
■ Automatic Key Lock function.......................................18
■ Priority A channel selection.........................................18
iv
 1 ACCESSORIES

■ Supplied accessories ■ Accessory attachments

The following accessories are supplied. D Flexible antenna
Connect the supplied flexible antenna
Flexible antenna Battery pack Belt clip to the antenna connector.
(This illustration is
for the UHF type.) CAUTION:
• NEVER carry the transceiver by
holding only the antenna.
• D O NOT connect the antenna
other than listed on page 29.
• Transmitting without an antenna
Connector cover may damage the transceiver.
(with screw)

1
 ACCESSORIES 1

D Battery pack D Belt clip 1

To attach the battery pack: To attach the belt clip:
Slide the battery pack on the back of the transceiver in the direc- q Remove the battery pack if it is attached. 2
tion of the arrow (q), then lock it with the battery release button. w Slide the belt clip in the direction of the arrow until the belt 3
• Slide the battery pack until the battery release button makes a ‘click’ clip is locked and makes a ‘click’ sound.
sound. 4
To remove the battery pack: 5
Push the battery release button in the direction of the arrow
(w) as shown below. The battery pack is then removed.
6
 EVER remove or attach the battery pack when the trans-
N 7
ceiver is wet or soiled. This may result water or dust get- 8
ting into the transceiver/battery pack and may result in the
transceiver being damaged. 9
To detach the belt clip: 10
q Remove the battery pack if it is attached. 11
w Pinch the clip (q), and slide the belt clip in the direction of
Battery pack
the arrow (w). 12
q
w 13
14
q
15
16
Battery release
button
w

NOTE: Keep the battery pack terminals clean. It’s a good

idea to occasionally clean them.
2
 1 ACCESSORIES

D Connector cover
To attach the connector cover: To detach the connector cover:
q Insert the connector cover into the multi-connector. qR  emove the screw using a phillips screwdriver.
w Tighten the screw. w Detach the connector cover for the optional equipment
connector.

Multi-
connector

q
w

w q

Connector
cover

CAUTION:
Attach the connector cover when the optional equipment
is not used. Otherwise the terminals of the multi-connec-
tor may be shorted by metal object, etc., and this could
damage the transceiver.

3
 PANEL DESCRIPTION 2
■ Front panel 1
q r DEALER-PROGRAMMABLE KEY [Side1] 2
w !2  Desired function can be programmed by your dealer. 3
e (p. 6)
!1 4
t PTT SWITCH [PTT]
r Speaker Push and hold to transmit; release to receive. 5
!0 y DEALER-PROGRAMMABLE KEYS [Side2]/[Side3] 6
t Desired function can be programmed independently by
Microphone
your dealer. (p. 6)
7
o 8
u 10-KEYPAD (Depending on version)
y
i The keypad allows you to enter digits to: 9
• Select memory channels
• Select tone channels 10
u • Select DTMF codes (during transmit)
• Set TX codes 11
• Start up with the password 12
i DEALER-PROGRAMMABLE KEYS [P0] to [P3]
Desired function can be programmed independently by
13
q ROTARY SELECTOR your dealer. (p. 6) 14
R
 otate to select the pre-programmed memory channels or
the operating zone. (Depending on the pre-setting)
o FUNCTION DISPLAY (p. 5) 15
Displays a variety of information such as an operating
w ANTENNA CONNECTOR channel number/name, Set mode contents, DTMF code, 16
Connects the supplied antenna. (p. 1) selected function, etc.
e DEALER-PROGRAMMABLE KEY [EMR]
D
 esired function can be programmed by your dealer.
(p. 6)

4
 2 PANEL DESCRIPTION

!0 MULTI-CONNECTOR
Connect an optional equipment.
■ Function display
q w e r ty u i

Connector cover
NOTE: Attach the connec-
tor cover when the optional
equipment is not used.
See page 3 for details.
o

CALA TXCU TXC SET !0

q SIGNAL STRENGTH INDICATOR

!1 BUSY/TRANSMIT INDICATOR
 Indicates relative signal strength level.
➥ Lights green while receiving a signal, or when the
squelch is open. w LOW POWER INDICATOR
➥ Lights red while transmitting.  Appears when low output power is selected.
!2 VOLUME CONTROL [VOL] e AUDIBLE INDICATOR
R
 otate to turn the power ON/OFF and adjusts the audio  ➥ Appears when the channel is in the ‘audible’ (unmute)
level. condition.
 ➥ Appears when the matched signal is received.
r COMPANDER INDICATOR
 Appears when the compander function is activated.
t SCRAMBLER INDICATOR
 Appears when the voice scrambler function is activated.

5
 PANEL DESCRIPTION 2

■ Programmable function keys 1

y BELL INDICATOR
2
The following functions can be assigned to [EMR], [Side1],
 Appears/blinks when the matched signal is received, ac- [Side2], [Side3], [P0], [P1], [P2] and [P3] programmable 3
cording to the pre-programming. function keys.
Consult your Icom dealer or system operator for details con-
4
u CALL CODE MEMORY INDICATOR
 Appears when the call code memory is selected.
cerning your transceivers programming. 5
If the programmable function names are bracketed in the fol-
i BATTERY INDICATOR lowing explanations, the specific key is used to activate the 6
 Appears or blinks when the battery power decreases to a function depends on the programming. 7
specified level.
CH UP AND DOWN KEYS “UP” “DOWN” 8
Indication
➥ Push to select an operating channel. When [Rotary selec- 9
Charging tor] selects “operating channel,” this key is not available.
Battery level Full Middle No battery
required ➥ Push to select a transmit code channel after pushing 10
blinks when the battery is over charged. [TX Code CH Select]. 11
blinks when the battery is exhausted.
➥ Push to select a DTMF channel after pushing [DTMF Au-
todial]. 12
➥ Push to select a scan group after pushing and holding
o ALPHANUMERIC DISPLAY
[Scan].
13
 ➥ Displays an operating channel number, channel name,
Set mode contents, DTMF code, etc. ➥ Push to select the desired application type, individual/talk- 14
group ID, TX status message and SDM (Short Data Mes-
➥ The indication mode can be selected from 1 line or 2
sage) after pushing [Digital Button].
15
lines. Ask your dealer for details.
• In this instruction manual, the LCD illustration is described 16
using the 2 lines indication mode.

!0 KEY INDICATOR
 Indicate the programmed function of the front panel keys
([P0], [P1], [P2] and [P3]).

6
 2 PANEL DESCRIPTION

ZONE KEY “ZONE” SCAN ADD/DEL (TAG) KEY “SCAD”

Push this key, then push [CH Up] or [CH Down] to select ➥ Push to add channel to, or delete it from the current scan
the desired zone. When [Rotary selector] selects “operating group.
zone,” this key operation is not available. 1. Push to indicate the scan group, then push [CH Up] or
[CH Down] to select the desired group.
 hat is “zone”?— Selected channels are assigned to a
W
2. Push to add or delete the channel to/from the selected
zone according to how they are to be used in a group. For
scan group.
example, ‘Staff A’ and ‘Staff B’ are assigned into a “Busi-
3. Push and hold for 1 sec. to exit the scan group selection
ness” zone, and ‘John’ and ‘Cindy’ are assigned into a “Pri-
mode.
vate” zone.
➥ Push this key while scan is paused (a signal is detected)
on a channel (except for priority channel,) the channel is
ZONE UP AND DOWN KEYS “ZNUP” “ZNDN”
cleared from the scan group.
Push to select an operating zone. When [Rotary selector] se-
lects “operating zone,” this key is not available.  epending on the setting, the cleared channel is added
D
to the scan group again after the scan is cancelled.
SCAN KEY “SCAN” (Nuisance Delete function)
➥ Push to start and cancel scanning operation.
• When Power ON Scan function is activated, push to pause the PRIORITY CHANNEL KEYS “PRA” “PRAR” “PRB” “PRBR”
scanning operation. And the paused scan restarts after the ➥ Push to select Priority A or Priority B channel.
specified time period has passed. ➥ Push and hold [Prio A (Rewrite)] or [Prio B (Rewrite)] for
➥ Push and hold this key for 1 sec. to indicate the scan list, 1 sec. to rewrite the Priority A or Priority B channel for the
then push [CH Up] or [CH Down] to select the desired list. operating channel.

7
 PANEL DESCRIPTION 2

MEMORY CH 1/2/3/4 KEYS “CH1” “CH2” “CH3” “CH4” LONE WORKER KEY “LONE” 1
Push to select the memory channels 1 to 4 directly. Push to turn the Lone Worker function ON or OFF.
• If the Lone Worker function is activated, the Emergency function is 2
MONI KEY “MON” automatically turned ON after the specified time period has passed
with no operation is performed. 3
➥ Push to mute and release the CTCSS (DTCS) or 2-Tone
squelch mute. Open any squelch/deactivate any mute 4
while pushing and holding this key. (LMR operation only) HIGH/LOW KEY “H/L”
➥ Activates one of (or two of) the following functions on each Push to select the transmit output power temporarily or per- 5
channel independently: (PMR operation only) manently, depending on the pre-setting. 6
• Push and hold to un-mute the channel (audio is emitted; ‘Audible’ • Ask your dealer for the output power level for each selection.
condition). 7
• Push to mute the channel (sets to ‘Inaudible’ only). TONE/RAN CH SELECT KEY “T SEL”
• Push after the communication is finished to send a ‘reset code’. ➥ While in analog mode operation, push to enter the continu-
8
(5-Tone/BIIS operation only) ous tone channel selection mode. Then select the desired 9
 OTE: The un-mute condition (‘Audible’ condition) may
N tone frequency/code setting with [CH Up] or [CH Down].
After the selection, push this key again to set.
10
automatically return to the mute condition (‘Inaudible‘
condition) after a specified period. ➥ While in digital mode operation, push to enter the RAN 11
channel selection mode. Then select the desired RAN set-
LIGHT KEY “LIGT” ting with [CH Up] or [CH Down]. After the selection, push 12
Push to turn the transceiver’s backlight ON temporarily only this key again to set. 13
when the backlight function is turned OFF in the User Set ➥ While in mixed (digital and analog) mode operation, push
mode. to enter the continuous tone channel selection mode. Then 14
select the desired tone frequency/code setting with [CH 15
LOCK KEY “LOCK” Up] or [CH Down]. After the selection, push this key to set.
➥ Push and hold for 1 sec. to electronically lock all program- After that, the RAN channel selection screen appears. Se- 16
mable keys for preventing accidental frequency changes lect the desired RAN setting with [CH Up] or [CH Down].
and unnecessary function access except the following: After the selection, push this key again to set.
[PTT], [Call] (incl. Call A and Call B), [Moni(Audi)],
[Light], [Emergency], [Surveillance], [Lone Worker] and
[OPT 1/2/3].
➥ Push and hold for 1 sec. again to turn the lock function OFF. 8
 2 PANEL DESCRIPTION

C.TONE CH ENT KEY “TSEL” CALL KEYS “CALL” “CALA” “CALB”

Push to enter the continuous tone channel selection mode. Push to transmit a 2/5-Tone or BIIS ID code.
Then select the desired tone frequency/code setting with [CH • Call transmission is necessary before you call another station
Up]/[CH Down]. The selected channel remains set as the depending on your signaling system.
continuous tone channel until another channel is designated • [Call A] and/or [Call B] may be available when your system employs
as such. selective ‘Individual/Group’ calls. Ask your dealer which call is
assigned to each key.
TALK AROUND KEY “TA”
EMERGENCY KEY “EMR”
Push to turn the talk around function ON and OFF.
• The talk around function equalizes the transmit frequency to the
Push and hold to transmit the emergency call.
• The emergency call transmits with beeps; the display does not
receive frequency for transceiver-to-transceiver communication.
change.
• The transceiver can transmit the emergency call silently or with the
WIDE/NARROW KEY “W/N” display changes depending on the pre-setting. Ask your dealer for
Push to toggle the IF bandwidth between wide and narrow. details.
• If you want to cancel the emergency call, push and hold the key
DTMF AUTODIAL KEY “DTMA” again before transmitting the call.
Push to enter the DTMF channel selection mode. Then select • The emergency call is transmitted one time only or repeatedly until
the desired DTMF channel using [CH Up]/[CH Down]. After receiving a control code, depending on the pre-setting.
selecting the DTMF channel, push again to transmit the
selected DTMF code. SURVEILLANCE KEY “SURV”
Push to turn the surveillance function ON or OFF.
RE-DIAL KEY “DTMR” When this function is turned ON, the beep is not emitted and
Push to transmit the last-transmitted DTMF code. the LCD backlight does not light when a signal is received or
a key is pushed, etc.

TX CODE ENTER KEYS “TXCE”

Push to enter the ID code edit mode directly, for both 5-Tone
and MSK. Then set the desired digit using [CH Up]/[CH
Down]. (p. 15)

9
 PANEL DESCRIPTION 2

TX CODE CHANNEL SELECT KEY “TXC” USER SET MODE KEY “SET” 1
Push to enter the TX code channel selection mode. Then set ➥ Push and hold for 1 sec. to enter the User Set mode.
the desired channel using [CH Up]/[CH Down]. (pp. 14, 15) • During the User Set mode, push this key to select an item, and 2
change the value or condition using push [CH Up]/[CH Down].
➥ Push and hold this key for 1 sec. again to exit the User Set
3
TX CODE CHANNEL UP/DOWN KEYS “TXCU” “TXCD”
Push to select a TX code channel directly. mode. 4
ID-MEMORY SELECT KEY “IDMS” OPT OUT KEYS “OP1” “OP2” “OP3” 5
➥ Recalls detected ID codes. Push to control the output signal level from the optional unit 6
• Push this key, then select the ID code using [CH Up]/[CH connector.
Down]. 7
• Up to 5 ID’s are memorized. OPT MOMENTARY KEYS “O1M” “O2M” “O3M” 8
➥ Push and hold for 1 sec. to erase the selected ID’s. Push to control the output signal level from the optional unit
connector. 9
SCRAMBLER/ENCRYPTION KEY “SCR”
➥ While in the analog mode operation, push to toggle the
10
voice scrambler function ON and OFF. 11
➥ While in the digital mode operation, push to toggle the
encryption transmission function ON and OFF.
12
13
COMPANDER KEY “COMP”
Push to toggle the compander function ON and OFF. 14
The compander function reduces noise components from the 15
transmitting audio to provide clear communication.
16

10
 3 BASIC OPERATION

■ Turning power ON
 rior to using the transceiver for the first time, the battery
P D Battery type selection
pack must be fully charged for optimum life and operation. The battery type must be selected according to the attaching
(p. 19) battery type when tuning the transceiver ON.

q Rotate [VOL] to turn the power ON. ➥ While pushing and holding [Emer] and [PTT], rotate [VOL]
w If the transceiver is programmed for a start up password, to toggle the attaching battery type.
input the digit codes as directed by your dealer. • After the display appears, release [Emer] and [PTT].
• 1 0-keypad can be used for password input depending on • “DRY BATT” is displayed for about 3 sec. then “Lo” (low power
version. indicator) appears when the battery case operation is selected.
• The keys in the table below can be used for password input. • “LI-ION” is displayed for about 3 sec. when the Lithium-ion bat-
• The transceiver detects numbers in the same block as identical. tery operation is selected.
Therefore “01234” and “56789” are the same.
• This operation may not be available depending on the pre-setting.
KEY P0 P1 P2 P3 (Side1) Ask your dealer for details.

0 1 2 3 4
NUMBER
5 6 7 8 9

e When the “PASSWORD” indication does not clear after

inputting 6 digits, the input code number may be incorrect.
Turn the power off and start over in this case.

11
 BASIC OPERATION 3

■ Channel selection 1
2
Several types of channel selections are available. Methods D Voting operation (for zone selection)
may differ according to your system set up. The transceiver automatically starts scanning when a zone, 3
specified for the voting operation, is selected.
NON-ZONE TYPE:
4
The voting scan detects the S-meter of the repeater and
To select the desired operating channel: automatically selects the strongest station. 5
• Push [CH Up] or [CH Down].
• Rotate [ROTARY SELECTOR]*.
6
- Up to pre-programmed 16 channels can be selected. 7
• Push one of [MR-CH 1] to [MR-CH 4].
8
ZONE TYPE: 9
To select the desired zone:
• Push [Zone], then push [CH Up] or [CH Down]. 10
• Push [Zone Up] or [Zone Down]. 11
• Rotate [ROTARY SELECTOR]*.
- Up to pre-programmed 16 zones can be selected. 12
* Depending on the pre-setting. 13
When [Rotary selector] selects “Operating channel,” [CH Up]/[CH 14
Down] are not available.
When [Rotary selector] selects “Operating zone,” [Zone]/[Zone Up]/ 15
[Zone Down] are not available.
16
AUTOMATIC SCAN TYPE:
Channel setting is not necessary for this type. When turning
power ON, the transceiver automatically starts scanning.
Scanning stops when receiving a call.

12
 3 BASIC OPERATION

■ Call procedure ■ Receiving and transmitting

When your system employs tone signalling (excluding CAUTION: Transmitting without an antenna may damage
CTCSS and DTCS), this call procedure may be necessary the transceiver. See page 1 for accessory attachments.
prior to voice transmission. The tone signalling employed may
be a selective calling system which allows you to call specific Receiving:
station(s) only and prevent unwanted stations from contacting q Rotate [VOL] to turn the power ON.
you. w Push [CH Up] or [CH Down], or rotate [ROTARY SELEC-
TOR]* to select the conventional system channel, in se-
q Select the desired TX code channel or 2/5-Tone code quence.
according to your System Operator’s instructions. *Depending on the pre-setting.
• This may not be necessary depending on programming. e When receiving a call, adjust the audio output level to a
• Refer to pages 14 or 15 for selection. comfortable listening level.
w Push [Call] (assigned to one of the dealer programmable NOTE: When a matched RX code signal is received, audio
keys). from the microphone is automatically transmitted for a
e After transmitting, the remainder of your communication specified time period.*
can be carried out in the normal fashion. * Depending on the presetting. Ask your dealer for details.
Selective calling Non-selective calling
Transmitting:
Wait for the channel to become clear to avoid interference.
q While pushing and holding [PTT], speak into the micro-
phone at a normal voice level.
• When a tone signalling system is used, the call procedure de-
scribed at the previous page may be necessary.
w Release [PTT] to return to receive.

IMPORTANT: To maximize the audio quality of your signal;

1. Pause briefly after pushing [PTT].
2. Hold the microphone 5 to 10 cm (2 to 4 inches) from
your mouth, then speak into the microphone at a normal
voice level.
13
 BASIC OPERATION 3

1
D Transmitting notes D TX code channel selection 2
• Transmit inhibit function If the transceiver has [TX Code CH Select] assigned to it, 3
The transceiver has several inhibit functions which restrict the indication can be toggled between the operating channel
transmission under the following conditions: number (or name) and TX code channel number (or name). 4
- The channel is in mute condition (‘Inaudible’ condition; When the TX code channel number (or name) is displayed, 5
“ ” (Audible indicator) does not appear.) [CH Up] or [CH Down] selects the TX code channel.
- The channel is busy. 6
- Un-matched (or matched) CTCSS is received. USING [TX CODE CH SELECT] KEY: 7
(Depending on the pre-setting.) q Push [TX Code CH Select]— a TX code channel number
- The selected channel is a ‘receive only’ channel. (or name) appears. 8
w Push [CH Up] or [CH Down] to select the desired TX code 9
• Time-out timer channel.
After continuous transmission for the pre-programmed time e After selecting, push [TX Code CH Select] to set. 10
period, the time-out timer starts, causing the transceiver to • Return to the stand-by mode.
stop transmitting. r Push [Call] to transmit the selected TX code.
11
12
• Penalty timer USING [TX CODE CH UP]/[TX CODE CH DOWN] KEY:
Once the time-out timer starts, transmission is further inhib- If the transceiver has a [TX Code CH Up] or [TX Code CH 13
ited for a period determined by the penalty timer. Down] key assignment, the programmed TX code channel 14
can be selected directly when pushed.
15
16
☞ Continue to the next page

14
 3 BASIC OPERATION

D TX code number edit (PMR operation only) USING [TX CODE ENTER] KEY:
If the transceiver has [TX Code CH Select] or [TX Code q After pushing [TX Code CH Select], push [CH Up] or [CH
Enter] assigned to it, TX code contents can be edited within Down],
the allowable digits. or push [TX Code CH Up] or [TX Code CH Down] to select
the desired TX code channel.
USING [TX CODE CH SELECT] KEY: w Push [TX Code Enter] to enter the TX code edit mode.
q Push [TX Code CH Select] to enter the TX code channel • The digit to be edited blinks.
selection mode. e Push [TX Code Enter] to select the desired digit to be ed-
• Select the desired operating channel before entering the TX ited.
code channel selection mode if necessary. r Push [CH Up]/[CH Down] to select the desired digit.
w Push [TX Code CH Select] for 1 sec. to enter the TX code t Push [TX Code Enter] to set. The digit to the right will blink
edit mode. automatically.
• The digit to be edited blinks. y Repeat r and t to edit all allowable digits.
e Push [TX Code CH Select] to select the desired digit to be u After editing, push [TX Code Enter] to set.
edited. • Return to the stand-by mode.
r Push [CH Up]/[CH Down] to select the desired digit. i Push [Call] to transmit.
t Push [TX Code CH Select] to set. The digit to the right will
blink automatically. D DTMF transmission
y Repeat r and t to edit all allowable digits. If the transceiver has [DTMF Autodial] assigned to it, the
u After editing, push [TX Code CH Select] to set. automatic DTMF transmission function is available. Up to 8
• Return to the stand-by mode. DTMF channels are available.
i Push [Call] to transmit.
q Push [DTMF Autodial]— a DTMF channel appears.
w Push [CH Up] or [CH Down] to select the desired DTMF
channel.
e Push [DTMF Autodial] to transmit the DTMF code.

15
 BASIC OPERATION 3

■ User set mode ■ Scrambler function 1

The User Set mode allows you to set seldom-changed set- The voice scrambler function provides private communica-
2
tings. If the transceiver has [User Set Mode] assigned to it, tion between stations. All versions have a built-in frequency 3
you can “customize” the transceiver operation to suit your inversion type scrambler; however, an optional rolling or non-
preferences and operating style. rolling type is available as well. 4
5
Entering the User Set mode: ➥ Push [Scrambler] to toggle the scrambler function ON or
q Push and hold [User Set Mode] to enter the User Set OFF. 6
mode.
w Push [User Set Mode] several times to select the appro-
•“ ” (Scrambler indicator) appears when the function is ON. 7
priate item. Then push [CH Up] or [CH Down] to set the 8
desired level/condition. ■ Stun function 9
• In the User Set mode, the selectable items are preset by your
dealer. The presetable items are Backlight, LCD contrast, When the specified ID, set as a stun ID or kill ID, is received, 10
Beep, Beep Level, Ringer Level, SQL Level, AF Min Level, the stun function is activated.
Mic Gain, VOX Gain*, VOX Delay*, Battery Voltage, Signal When the stun ID is received, the transceiver becomes unus- 11
Moni, Lone Worker and System Info.
able. Entering of the password (p. 11) or receiving a specified 12
* Appears only when the external VOX unit is connected.
ID, set as a revive ID, is necessary to operate the transceiver
e Push and hold [User Set Mode] again to exit the User Set 13
again in this case.
mode.
When the kill ID is received, the transceiver switches to the 14
cloning required condition. Cloning the transceiver is neces-
sary to operate the transceiver again in this case. 15
16

16
 3 BASIC OPERATION

■ Emergency transmission
When [Emergency] is pushed for the specified time period*, D NOTES
the emergency signal is transmitted once, or repeatedly, on Depending on the presetting, the following functions are auto-
the specified emergency channel. matically activated. Ask your dealer for details.
• Auto TX function
A repeat emergency signal is automatically transmitted until
After the emergency call transmission, audio from the micro-
the transceiver receives an acknowledgement signal, or you
phone is automatically transmitted for a specified time period.*
turn the transceiver power OFF.
When no emergency channel is specified, the signal is trans- • Auto RX function
mitted on the previously selected channel. After the emergency call transmission, the transceiver stands
by in the audible mode for the specified time period.*
If you want to cancel the emergency call, push and hold
[Emergency] again before transmitting the call.
■ Man Down Emergency Call
If your transceiver is programmed for Silent operation, you
can transmit an Emergency call without the beep sounding This function requires the optional UT-124R man down unit.
and the LED indicator lighting. When the transceiver has been left in a horizontal position for
the specified time period*, the transceiver enters the emer-
IMPORTANT: It is recommended to set an emergency gency mode, and then the countdown starts.
channel individually to provide the certain emergency call After the specified time period* has passed, an emergency
operation. call is automatically transmitted once, or repeatedly.
If the transceiver is placed in a vertical position before the first
transmission, the transceiver exits the emergency mode and
the emergency call is cancelled.
* Depending on the presetting. Ask your dealer for details. IMPORTANT: It is recommended to set an emergency
channel individually to provide the certain emergency call
operation.

17
 BASIC OPERATION 3

■ Automatic Key Lock function 1

2
When [Lock] is assigned to any key and the Automatic Key Lock
timer is pre-programmed* by your dealer, the key lock function 3
can be automatically turned ON after the specified time period
has passed without operation during standby condition.
4
While the lock function is ON, push and hold [Lock] for 1 sec.
5
to turn the function OFF. 6
*When “0” is programmed, this function is not available. 7
8
■ Priority A channel selection 9
When one of the following operations is performed, the trans- 10
ceiver selects the Priority A channel automatically.
11
• Turning the power ON
The Priority A channel is selected each time the trans-
12
ceiver power is turned ON. 13
• Status call
The Priority A channel is selected when transmitting a 14
status call. (BIIS operation only) 15
• Clear down
The Priority A channel is selected after the clear down 16
signal is transmitted.

18
 4 BATTERY CHARGING

■ Caution
• Misuse of Lithium-ion batteries may result in the following R DANGER! KEEP battery packs away from fire. Fire or heat
hazards: smoke, fire, or the battery may rupture. Misuse may cause them to rupture or explode. Dispose of used bat-
can also cause damage to the battery or degradation of tery packs in accordance with local regulations.
battery performance. R DANGER! NEVER solder the battery terminals or NEVER
• Prior to using the battery pack for the first time, or after modify the battery pack. This may cause heat generation, and
not using it for a long time, you must fully charge the pack. the battery may burst, emit smoke or catch fire.
Otherwise, the transceiver may not turn ON. R DANGER! Use the battery only with the transceiver for
which it is specified. Never use a battery with any other
D Battery caution equipment, or for any purpose that is not specified in this in-
R DANGER! DO NOT hammer or otherwise impact the bat- struction manual.
tery. Do not use the battery if it has been severely impacted
R DANGER! If fluid from inside the battery gets in your eyes,
or dropped, or if the battery has been subjected to heavy
blindness can result. Rinse your eyes with clean water, with-
pressure. Battery damage may not be visible on the outside
out rubbing them, and see a doctor immediately.
of the case. Even if the surface of the battery does not show
cracks or any other damage, the cells inside the battery may R WARNING! Immediately stop using the battery if it emits
rupture or catch fire. an abnormal odor, heats up, or is discolored or deformed. If
R DANGER! NEVER use or leave battery packs in areas any of these conditions occur, contact your Icom dealer or
with temperatures above +60˚C (+140˚F). High tempera- distributor.
ture buildup in the battery, such as could occur near fires R WARNING! Immediately wash, using clean water, any part
or stoves, inside a sun heated car, or in direct sunlight may of the body that comes into contact with fluid from inside the
cause the battery to rupture or catch fire. Excessive tempera- battery.
tures may also degrade battery performance or shorten bat- R WARNING! NEVER put the battery in a microwave oven,
tery life. high-pressure container, or in an induction heating cooker.
R DANGER! DO NOT expose the battery to rain, snow, sea- This could cause a fire, overheating, or cause the battery to
water, or any other liquids. Never charge or use a wet battery. rupture.
If the battery gets wet, be sure to wipe it dry before using.
The battery is not waterproof.
19
 BATTERY CHARGING 4

CAUTION: Always use the battery within the specified tem- D Charging caution 1
perature range for the transceiver (–30˚C to +60˚C; –22˚F R DANGER! NEVER charge the battery pack in areas with
to +140˚F) and the battery itself (–20˚C to +60˚C; –4˚F to extremely high temperatures, such as near fires or stoves,
2
+140˚F). Using the battery out of its specified temperature inside a sun heated vehicle, or in direct sunlight. In such en- 3
range will reduce the battery’s performance and battery life. vironments, the safety/protection circuit in the battery will ac-
CAUTION: Shorter battery life could occur if the battery is left tivate, causing the battery to stop charging. 4
fully charged, completely discharged, or in an excessive tem- R WARNING! NEVER charge or leave the battery in the 5
perature environment (above +50˚C; +122˚F) for an extended battery charger beyond the specified time for charging. If the
period of time. If the battery must be left unused for a long battery is not completely charged by the specified time, stop
6
time, it must be detached from the transceiver after discharg- charging and remove the battery from the battery charger. 7
ing. You may use the battery until the remaining capacity is Continuing to charge the battery beyond the specified time
about half, then keep it safely in a cool dry place with the limit may cause a fire, overheating, or the battery may rup-
8
temperature range as below: ture. 9
–20˚C to +50˚C (–4˚F to +122˚F) (within a month)
R WARNING! NEVER insert the transceiver (battery at- 10
–20˚C to +40˚C (–4˚F to +104˚F) (within three months)
tached to the transceiver) into the charger if it is wet or soiled.
–20˚C to +20˚C (–4˚F to +68˚F) (within a year)
This could corrode the battery charger terminals or damage 11
BE SURE to replace the battery pack with a new one ap- the charger. The charger is not waterproof.
proximately five years after manufacturing, even if it still holds 12
CAUTION: NEVER charge the battery outside of the speci-
a charge. The inside battery material will become weak after
fied temperature range: BC-160 (0˚C to +40˚C; +32˚F to 13
a period of time, even with little use. The estimated number
+104˚F). Icom recommends charging the battery at +20˚C 14
of times you can charge the battery is between 300 and 500.
(+68˚F). The battery may heat up or rupture if charged out of
Even when the battery appears to be fully charged, the oper- 15
the specified temperature range. Additionally, battery perfor-
ating time of the transceiver may become short when:
mance or battery life may be reduced. 16
• Approximately five years have passed since the battery was
manufactured.
• The battery has been repeatedly charged.

20
 4 BATTERY CHARGING

■ Optional battery chargers

D Rapid charging with the BC-160 D Regular charging with the BC-171
The optional BC-160 provides rapid charging of the Li-ion The optional BC-171 provides regular charging of the Li-ion
battery pack. battery pack.
Charging time: Approximately 3.5 hours (with BP-232H) Charging time: Approximately 4 hours (with BP-230N)

The following items are additionally required: The following items are additionally required:
• A power adapter (may be supplied with BC-160 depending • A power adapter (may be supplied with BC-171 depending
on version) or the DC power cable (OPC-515L/CP-23L). on version) or the DC power cable (OPC-515L/CP-23L).
Power adapter Power adapter
(A different type, or no power adapter is Transceiver Transceiver
(A different type, or no power adapter is
supplied, depending on the version.) Turn OFF supplied, depending on the version.) Turn OFF
Battery the power Battery the power
pack pack

Optional OPC-515L* (for Optional OPC-515L* (for 13.8

13.8 V power source) or V power source) or CP-23L
CP-23L (for 12 V cigarette (for 12 V cigarette lighter
lighter socket) can be used socket) can be used instead
instead of the power adapter. of the power adapter.
* CAUTION: NEVER * CAUTION: NEVER
connect the OPC- connect the OPC-
515L to a power 515L to a power
source using reverse source using reverse
polarity. This will ruin polarity. This will ruin
the battery charger the battery charger
White line: White line:
Black line : Black line :
21
 BATTERY CHARGING 4

D AD-106 installation D Rapid charging with the BC-119N+AD-106 1

The AD-106 charger adapter must be installed into the BC- The optional BC-119N provides rapid charging of the Li-ion
119N or BC-121N before battery charging. battery pack. 2
Charging time: Approximately 3.5 hours (with BP-232H) 3
➥C
 onnect the AD-106 charger adapter and the BC-119N/
BC-121N as below, then install the AD-106 into the holder The following items are additionally required. 4
space of the BC-119N or BC-121N with the supplied • AD-106 charger adapter (purchase separately) 5
screws. • A power adapter (may be supplied with BC-119N depend-
ing on version) or the DC power cable (OPC-515L/CP-23L). 6
AD-106
Turn OFF 7
power adapter the power
Connectors Battery
(A different type, or no
pack Transceiver
8
power adapter is supplied,
depending on the version.) 9
10
AD-106 charger
11
Screws supplied
with the charger
adapter is installed 12
in BC-119N.
adapter 13
Sockets 14
Optional OPC-515L* (for 13.8
V power source) or CP-23L 15
(for 12 V cigarette lighter
socket) can be used instead 16
of the power adapter.
This illustration shows * CAUTION: NEVER connect the OPC-
the BC-119N. 515L to a power source using reverse
polarity. This will ruin the battery charger
White line: Black line :

22
 4 BATTERY CHARGING

D Rapid charging with the BC-121N+AD-106 IMPORTANT: Battery charging caution

The optional BC-121N allows up to 6 battery packs to be Ensure the guide tabs on the battery pack are correctly
charged simultaneously. aligned with the guide rails inside the charger adapter.
Charging time: Approximately 3.5 hours (with BP-232H) (This illustration is described with the BC-160.)

The following items are additionally required.

• Six AD-106 charger adapters (purchase separately)
• A power adapter or the DC power cable (OPC-656)
Turn OFF the power
Battery Transceiver
pack

Power adapter AD-106 charger

(Purchased adapters are installed Tabs
separately) in each slot.

Guide rail

CAUTION:
DC power cable (OPC-656*) When using the OPC-656 DC power cable
(Connect with a DC power supply; NEVER reverse the polarity when connecting the OPC-
13.8 V/at least 7 A) 656 to a power source. This will ruin the battery charger.
*About the OPC-656 OPC-656 : Red line: +, Black line: _
Red line : Black line :
23
 BATTERY CASE 5
■ Optional battery case (BP-240) 1
When using the optional battery case attached to the trans- Fig.1 w
2
ceiver, install 6 × AAA (LR03) size alkaline batteries as illus- BP-240 3
trated at right.
4
q Unhook the battery cover release hook (q), and open the
cover in the direction of the arrow (w). (Fig.1) 5
w T hen, install 6 × AAA (LR03) size alkaline batteries. q 6
(Fig.2)
• Install the alkaline batteries only. 7
• Be sure to observe the correct polarity. Fig.2
e Fit the cover in the direction of the arrow (e), then close
8
(r). And hook the battery cover release hook until it 9
makes a ‘click’ sound (t). (Fig.3)
10
CAUTION: 11
• W hen installing batteries, make sure they are all the
same brand, type and capacity. Also, do not mix new 12
and old batteries together.
• Keep battery terminals clean. It’s a good idea to clean
13
e
battery terminals once a week. Fig.3 14
• Never incinerate used battery cells since internal battery
gas may cause them to rupture.
15
r
• Never expose a detached battery case to water. If the bat- 16
tery case gets wet, be sure to wipe it dry before using it.
t
 OTE: When the optional battery case is attached, the
N
battery type must be selected to “DRY BATT” when turn-
ing the transceiver ON. (p. 11)

24
 6 SWIVEL BELT CLIP

■ MB-93 contents r C lip the belt clip to a part of your belt. And insert the
transceiver into the belt clip until the base clip inserted
fully into the groove.
Qty.
q Belt clip.............................................................................1
w Base clip...........................................................................1

q w

t Once the transceiver is locked in place, it swivels as illus-

■ To attach trated below.

q Remove the battery pack if it is attached. (p. 2)

w Slide the base clip in the direction of the arrow until the
base clip is locked and makes a ‘click’ sound.

Once the transceiver is locked in place,

it will swivel 360 degrees.
e Attach the battery pack. (p. 2)
25
 SWIVEL BELT CLIP 6

■ To detach 1
2
q Turn the transceiver upside down in the direction of the CAUTION:
arrow and pull out from the belt clip. HOLD THE TRANSCEIVER TIGHTLY, WHEN HANGING 3
OR DETACHING THE TRANSCEIVER FROM THE BELT 4
CLIP.
Otherwise the transceiver may not be attached to the 5
holder or swivel properly if the transceiver is accidentally
dropped and the base clip is scratched or damaged.
6
7
8
9
10
11
12
13
w Remove the battery pack if it is attached. (p. 2)
e Pinch the clip (q), and slide the base clip in the direction 14
of the arrow (w). 15
16
q w

26
 7 SPEAKER MICROPHONE

■O
 ptional HM-169/HM-170GP ■ To attach
description Attach the connector of the speaker-microphone into the multi
connector on the transceiver and tighten the screw.
TOP KEY
GPS ANTENNA
(for HM-170GP only)
(for HM-170GP only) CAUTION: Attach the
Desired functions can
Microphone multi connector snugly, but
be programmed by
do not overtighten.
your dealer.
Speaker A loose connection will al-
low water intrusion into the
PTT SWITCH Belt clip connector; an overtight-
Push and hold to ened connector will dam-
transmit; age the connector pins in
release to receive. the transceiver.

Turn the transceiver power

OFF when attaching or
detaching the microphone.
IMPORTANT: KEEP the connector cover attached to the
transceiver when the speaker-microphone is not in use.
This illustration is desicribed with HM-170GP.
(p. 3)
NEVER immerse the connector in water. If the connector Water will not get into the transceiver even if the cover is
becomes wet, be sure to dry it BEFORE attaching it to the not attached, however, the terminals (pins) will become
transceiver. rusty, or the transceiver will function abnormally if the con-
nector becomes wet.
NOTE: The microphone is located at the top of the
speaker-microphone, as shown in the diagram above. To
maximize the readability of your transmitted signal (voice),
hold the microphone approx. 5 to 10 cm (2 to 4 inches)
from your mouth, and speak in a normal voice level.
27
 OPTIONS 8
D BATTERY PACKS • BC-160 desktop charger + BC-123S ac adapter 1
Battery pack Voltage Capacity Battery life*1 For rapid charging of battery pack. A power adapter is sup-
plied with the charger depending on versions. 2
950 mAh (min.) Charging time: A pproximately 3.5 hours for the BP-232H.
BP-230N 7.4 V
980 mAh (typ.)
7.35 hrs. 3
• BC-171 desktop charger + BC-147S ac adapter
BP-232N 7.4 V
1900 mAh (min.)
12 hrs. For regular charging of battery packs. A power adapter is 4
2000 mAh (typ.) supplied with the charger depending on versions.
Charging time: A pproximately 11.5 hours for the BP-232H.
5
2250 mAh (min.)
BP-232H 7.4 V 14 hrs.
2300 mAh (typ.) Approximately 4 hours for the BP-230N. 6
BP-240
Battery case for AAA
—*2 D BELT CLIPS 7
(LR03) × 6 alkaline
• MB-93 swivel belt clip 8
*1 
When the power save function is turned ON, and the operating • MB-94 belt clip
periods are calculated under the following conditions; Exclusive alligator-type belt clip. 9
TX : RX : standby = 5 : 5 : 90
*2 Operating period depends on the alkaline cells used.
• MB-96N/MB-96F leather belt hanger 10
D CHARGERS D OPTIONAL UNITS 11
• BC-119N desktop charger + AD-106 charger adapter • UT-96R 2/5 tone unit 12
+ BC-145S ac adapter • UT-109R/UT-110R scrambler units
For rapid charging of battery pack. A power adapter is sup- Non-rolling type (UT-109R)/Rolling type (UT-110R) voice 13
plied with the charger depending on versions. scrambler unit provides higher communication security. 14
Charging time: Approximately 3.5 hours for the BP-232H. • UT-126H digital modulator/demodulator unit
•B  C-121N multi-charger + AD-106 charger adapter (6 pcs.) Provides 6.25 kHz digital mode operation. 15
+ BC-157S ac adapter • UT-124R man down unit 16
For rapid charging of up to 6 battery packs (six AD-106s are Provides a measure of safety when working in a hazardous
required) simultaneously. A power adapter should be pur- environment, etc.
chased separately.
Charging time: Approximately 3.5 hours for the BP-232H.

28
 8 OPTIONS

D DC CABLES D ANTENNAS
• CP-23L cigarette lighter cable • FA-SC56VS/FA-SC57VS/FA-SC73US stubby antennas
Allows charging of the battery pack through a 12 V cigarette Shorter VHF or UHF antennas.
lighter socket. (For BC-119N/BC-160/BC-171) FA-SC56VS: Frequency range 150–162 MHz
• OPC-515L/OPC-656 dc power cables FA-SC57VS: Frequency range 160–174 MHz
Allows charging of the battery pack using a 13.8 V power FA-SC73US: Frequency range 450–490 MHz
source instead of the power adapter. • FA-SC25V/FA-SC55V/FA-SC03U/
OPC-515L : For BC-119N/BC-160/BC-171 FA-SC25U/FA-SC57U/FA-SC72U flexible antennas
OPC-656 : For BC-121N VHF or UHF antennas.
FA-SC25V: Frequency range 136–150 MHz
D OTHER OPTIONS FA-SC55V: Frequency range 150–174 MHz
• SP-13 earphone FA-SC03U: Frequency range 380–430 MHz
Provides clear receive audio in noisy environment. FA-SC25U: Frequency range 400–430 MHz
• AD-52 earphone adapter FA-SC57U: Frequency range 430–470 MHz
Provides clear receive audio in noisy environment. FA-SC72U: Frequency range 470–520 MHz
• HM-131SC/HM-159SC speaker-microphone • FA-SC61VC/FA-SC61UC cut antennas
Combination speaker-microphone that provides convenient FA-SC61VC: 136–174 MHz
operation while hanging the transceiver from your belt. FA-SC61UC: 380–520 MHz
• HM-169 speaker-microphone
Rugged type speaker-microphone.
• HM-170GP speaker-microphone Approved Icom optional equipment is designed for optimal
GPS speaker-microphone for BIIS and Digital modes opera- performance when used with an Icom transceiver.
tion. Icom is not responsible for the destruction or damage to an
• VS-1SC vox/ptt case + HS-94/HS-95/HS-97 headset Icom transceiver in the event the Icom transceiver is used with
VS-1SC : VOX/PTT switch box for hands-free operation, etc. equipment that is not manufactured or approved by Icom.
HS-94 : Ear-hook type
HS-95 : Neck-arm type Some options may not be available in some countries. Please ask
HS-97 : Throat microphone your dealer for details.
• MB-130 vehicle charger bracket
Vehicle mounting bracket for the BC-160 battery charger.
29
 OPTIONS 8

D About VS-1SC vox/ptt case 1

The VS-1SC is a VOX/PTT unit for Icom handheld transceiv- VOX gain and delay adjustment
ers, and allows you hands-free operation. NOTE: To adjust the VOX gain and VOX delay, these items 2
An optional headset (HS-94, etc.) is required for operation. must be preset to “enable” by your dealer. 3
• The VOX (Voice Operated Transmission) function starts transmission
without pushing PTT switch when you speak into the microphone; q Attach the connector of the VS-1SC into the multi-connec- 4
then, automatically returns to receive when you stop speaking. tor on the transceiver and tighten the screw.
• Toggle the VOX/PTT select switch to [VOX].
5
Features w Push and hold [User Set Mode] for 1 sec. to enter the User 6
➥ 9-pin Spring-plug type head SP/MIC plug is equipped Set mode.
➥ Water resistant construction e Push [User Set Mode] several times to select “VOX Gain”
7
➥ Durable construction or “VOX Delay.” Then, push [CH Up] or [CH Down] to set 8
➥ Equipped with a PTT switch and revolving clip the desired level/condition.
MIC/VOX gain r Push and hold [User Set Mode] for 1 sec. to exit the User 9
adjusting pot VS-1SC
PTT switch Set mode. 10
• VOX Gain 11
Water protection cover The VOX sensitivity level can be adjusted from OFF or 1 to 6 12
(more sensitive).
VOX/PTT select switch
13
[Side2] 14
VOX OFF Push VOX GAIN 3
[Side3] 15
SET TXCU TXC CALA SET TXCU TXC CALA
16
VOX function is OFF VOX gain level 3
(default)

30
 8 OPTIONS

• VOX Delay
The VOX delay time can be set from 0.5 to 3.0 sec. (0.5 sec.
step) for a convenient interval before returning to receive.

[Side2]
VOX DLY0.5 Push VOX DLY3.0
[Side3]
SET TXCU TXC CALA SET TXCU TXC CALA
0.5 sec (min.) 3.0 sec (max.)
(default)

 OTE: MIC/VOX gain can be adjusted via the Adjusting

N
pot using a thin screw driver.

SET X TXC SET X TXC

31
 SAFETY TRAINING INFORMATION 9
Your Icom radio generates RF electromagnetic To ensure that your expose to RF electromag- 1
energy during transmit mode. This radio is de- netic energy is within the FCC and IC allowa-
signed for and classified as “Occupational Use ble limits for occupational use, always adhere 2
Only”, meaning it must be used only during the to the following guidelines:
C AU TIO N 3
W ARN ING course of employment by individuals aware of the
hazards, and the ways to minimize such hazards. • D O NOT operate the radio without a proper antenna at- 4
This radio is NOT intended for use by the “General Population” tached, as this may damaged the radio and may also cause
in an uncontrolled environment. you to exceed FCC and IC RF exposure limits. A proper 5
This radio has been tested and complies with the FCC and IC antenna is the antenna supplied with this radio by the man-
RF exposure limits for “Occupational Use Only”. In addition, your ufacturer or antenna specifically authorized by the manufac-
6
Icom radio complies with the following Standards and Guide- turer for use with this radio. 7
lines with regard to RF energy and electromagnetic energy lev- • DO NOT transmit for more than 50% of total radio use time
els and evaluation of such levels for exposure to humans: (“50% duty cycle”). Transmitting more than 50% of the time 8
• FCC OET Bulletin 65 Edition 97-01 Supplement C, Evaluat- can cause FCC and IC RF exposure compliance require- 9
ing Compliance with FCC Guidelines for Human Exposure ments to be exceeded. The radio is transmitting when the
to Radio Frequency Electromagnetic Fields. TX indicator lights red. You can cause the radio to transmit 10
• American National Standards Institute (C95.1-1992), IEEE by pressing the “PTT” switch.
Standard for Safety Levels with Respect to Human Expo- • ALWAYS keep the antenna at least 2.5 cm (1 inch) away
11
sure to Radio Frequency Electromagnetic Fields, 3 kHz to from the body when transmitting and only use the Icom belt- 12
300 GHz. clips listed on page 28 when attaching the radio to your
• American National Standards Institute (C95.3-1992), IEEE belt, etc., to ensure FCC and IC RF exposure compliance 13
Recommended Practice for the Measurement of Potentially requirements are not exceeded. To provide the recipients of
Hazardous Electromagnetic Fields– RF and Microwave. your transmission the best sound quality, hold the antenna
14
• The following accessories are authorized for use with this at least 5 cm (2 inches) from your mouth, and slightly off to 15
product. Use of accessories other than those specified may one side.
result in RF exposure levels exceeding the FCC and IC 16
requirements for wireless RF exposure.; Belt Clip (MB-93, The information listed above provides the user with the infor-
MB-94, MB-96N and MB-96F), Rechargeable Li-ion Bat- mation needed to make him or her aware of RF exposure, and
tery Pack (BP-230N/BP-232N/BP-232H), Alkalies Battery what to do to assure that this radio operates with the FCC and
Case (BP-240) and Speaker-microphone (HM-131SC, HM- IC RF exposure limits of this radio.
159SC, HM-169 and HM-170GP).
32
 9 SAFETY TRAINING INFORMATION

Electromagnetic Interference/Compatibility Votre radio Icom produit une énergie électroma-

During transmissions, your Icom radio generates RF energy that gnétique de radiofréquences (RF), en mode de
can possibly cause interference with other devices or systems. transmission. Cette radio est conçue pour un
To avoid such interference, turn off the radio in areas where «usage professionnel seulement» et classée
signs are posted to do so. DO NOT operate the transmitter in comme tel, ce qui signifie qu’elle doit être utilisée
areas that are sensitive to electromagnetic radiation such as uniquement dans le cadre d'un travail par des personnes
hospitals, aircraft, and blasting sites. conscientes des dangers et des mesures visant à minimiser ces
dangers. Elle N’EST PAS conçue pour une «utilisation grand pu-
Occupational/Controlled Use
blic», dans un environnement non contrôlé.
The radio transmitter is used in situations in which persons are
exposed as consequence of their employment provided those Cet appareil a été évalué et jugé conforme, aux limites d’expo-
persons are fully aware of the potential for exposure and can sition aux RF de la FCC et d’IC, pour une «utilisation grand pu-
exercise control over their exposure. blic». En outre, votre radio Icom satisfait les normes et directives
qui suivent en matière de niveaux d'énergie et d’énergie élec-
tromagnétique de RF et d’évaluation de tels niveaux en ce qui
concerne l’exposition humaine:
• Supplément C, édition 97-01, du Bulletin OET n° 65 de la
FCC, «Evaluating Compliance with FCC Guidelines for
Human Exposure to Radio Frequency Electromagnetic
Fields».
• Norme de l’American National Standards Institute (ANSI):
IEEE C95.1-1992 sur les niveaux de sécurité compatibles
avec l’exposition humaine aux champs électromagnétiques
de radiofréquences (3 kHz à 300 GHz).
• Norme de l’ANSI: IEEE C95.3-1992 sur la méthode d’éva-
luation recommandée du champ magnétique potentiellement
dangereux des radiofréquences et des micro-ondes.
• Les accessoires illustrés à la p. 28–29 sont approuvés pour
une utilisation avec ce produit. L’utilisation d’accessoires
autres que ceux précisés peut entraîner des niveaux d’expo-
sition aux RF supérieures aux limites établies par la FCC et
d’IC en matière d’exposition aux RF sans fil.
33
 SAFETY TRAINING INFORMATION 9

Afin de vous assurer que votre exposition à Les renseignements ci-dessus fournissent à l’utilisateur toute l’in- 1
une énergie électromagnétique de RF se formation nécessaire sur l’exposition aux RF et sur ce qu’il faut
situe dans les limites permises par la FCC faire pour assurer que cette radio fonctionne en respectant les limi- 2
tes d’exposition aux RF établies par la FCC et d’IC.
et d’IC pour une utilisation grand public, 3
veuillez en tout temps respecter les directi- Interférence électromagnétique et compatibilité
ves suivantes: En mode de transmission, votre radio Icom produit de l’énergie de 4
• NE PAS faire fonctionner la radio sans qu’une antenne appro- RF qui peut provoquer des interférences avec d’autres appareils
ou systèmes. Pour éviter de telles interférences, mettez la radio
5
priée y soit fixée, car ceci risque d’endommager la radio et cau-
ser une exposition supérieure aux limites établies par la FCC et hors tension dans les secteurs où une signalisation l’exige. NE 6
d’IC. L’antenne appropriée est celle qui est fournie avec cette PAS faire fonctionner l’émetteur dans des secteurs sensibles au
radio par le fabricant ou une antenne spécialement autorisée par rayonnement électromagnétique tels que les hôpitaux, les aéro- 7
le fabricant pour être utilisée avec cette radio. nefs et les sites de dynamitage. 8
• NE PAS émettre pendant plus de 50 % du temps total d’utili- Usage professionnel/contrôlé
sation de l’appareil («50 % du facteur d'utilisation»). La notion Ce radio émetteur est utilisé dans des cas où des personnes sont 9
«50% du facteur d’utilisation» s’applique également au mode exposées en raison de leur travail, pourvu qu’elles soient conscien-
VOX/PTT. Émettre pendant plus de 50 % du temps total d’utili-
10
tes du risque d’exposition et qu’elles puissent exercer un contrôle
sation peut causer une exposition aux RF supérieure aux limi- sur cette exposition. 11
tes établies par la FCC et d’IC. Lorsque le voyant DEL rouge
s’allume, cette radio est en train d’émettre. La radio émettra si 12
vous appuyez sur le bouton du microphone. 13
•T OUJOURS tenir l’antenne éloignée d’au moins 2,5 cm de
votre corps au moment d’émettre et utiliser uniquement l’at- 14
tache pour ceinture Icom illustrée à la p. 28, lorsque vous at-
tachez la radio à votre ceinture, ou à autre chose, de façon
15
à vous assurer de ne pas provoquer une exposition aux RF 16
supérieure aux limites fixées par la FCC et d’IC. Pour offrir à
vos interlocuteurs la meilleure qualité de transmission possible,
tenez l’antenne à au moins 5 cm de votre bouche et légère-
ment de côté.

34
A-6638H-1EX-i
Printed in Japan
© 2007–2015 Icom Inc.
Printed on recycled paper with soy ink.
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan