Visibly yours
Operations Quick Start Guide
Digital Cinema Projector Components
Lens Touch Panel Touch Panel Connector Exhaust Port
Always remove lens cap prior to Used for normal operation Provides power and Used to remove heat from the lamp
use. Refer to User’s Guide for or for troubleshooting the communication for the compartment. Important: The
recommended cleaning practices. projector Touch Panel extraction system must be running.
Front and left Rear and left
side view side view
Input Tray Keypad 5-Pin XLR Tail Light Mains Power Switch
Used for video, communication Used for lamp power, dowser This connector is Green = System OK Powers the projector on and off. This switch shuts
and alternative content control, macros, lens currently not off all electrical connection to the projector. The
connections to the projector adjustments and test patterns implemented. Red = Error Condition lamp must be cooled down before switching off.
P/N R59990110, Rev 01
Features
Macro Buttons Lens Adjustment Lamp Dowser Control Test Pattern Focus
Used to preset the Positions the image Press once to turn the Press once to open the Press to enable and Adjusts
projector configuration on screen. Used for lamp on. Press once dowser. Press once to cycle through primary
for each show manual override. to turn the lamp off. close the dowser. the test patterns image focus
When the Test
Pattern or Macro button
is used, it will first light up
NOTE
“purple” while in
transition, and then turn
“red” when completed.
Keypad
Dallas Key
Security feature for Dallas
Key receiver (secure
function authorization)
Zoom
Increases or decreases
image size
Input Tray
SMPTE 292 BNC DVI-D Connectors Ethernet
Connectors Accepts data signals from Used for communication from the
Accepts an encrypted content alternative content devices such projector to the content server
data stream from the server as ACS-2048 and theater management system
Daily Procedures
1. Power Up 3. Play a Movie
Procedure Procedure
Ensure that the extraction system is on. During normal operations, the server should
1 1 2 4
2 start the projector automatically. If the
projector is not automatically started by the
Switch on the Mains Power. Allow up to server, follow the steps below.
2
one minute for the projector to finish the
boot-up sequence. Press the Lamp button. Wait five seconds
2
between each step.
Select the appropriate Macro. Wait five
3
seconds between each step.
If the projector’s tail lights turn red, refer to Press the Dowser button.
3 4
the Troubleshooting section in this guide.
Remove the lens cap (if applicable). Start the movie from the server.
4 5
3
3
Check the content on screen for the proper
6
alignment and color.
2. Pre-operation Setup 4. Power Down
1
Procedure Procedure
1 2
Press the Lamp button to strike the lamp. If the lamp is on, press the Lamp button and
1 6 6 1
allow the lamp to cool for 10 minutes prior to
electrical power down.
Press the Dowser Control Button to open
2
the dowser.
Not allowing the lamp to
Press the desired scope or flat Macro Important cool will result in lamp
3
required for the next show playing in damage!
auditorium. Allow up to one minute for
the lens to move into position. The image
2
may appear off screen at first. After the 10 minute cool down period, switch
2
Play movie from the server and check the off the projector’s Mains Power.
4
image to ensure that it is properly aligned
with the screen masking.
5 If the image is not aligned with the screen 3 5
masking, use the Lens Adjustment 5. Pre-show Maintenance
Buttons to correct the image on screen.
Notify the theater technician. Procedure
Turn the lamp off and close the dowser
6
until “showtime” nears. When needed, clean the Lens with a lens
1
cloth.
1
When needed, clean the Port Window.
2
For full details on all maintenance activities,
3
refer to the Maintenance Guide.
Troubleshooting
Problem: The lamp does not strike Problem: There is no image on the screen
Procedure Check the following potential causes: 1 Procedure Check the following potential causes:
Press the Lamp button. Between each strike Check to see if the lamp is on and the 1 5
1 1
attempt, allow 10 seconds (if lamp is cold) or Dowser is open.
1 minute (if lamp is hot).
Check that the Lens Cap is removed.
2
If after the third attempt the lamp does not
2
strike, contact the theater’s technician.
Verify that the correct Macro is selected.
3
Problem: Movies or trailers are not playing with the correct color 4 Verify that the server is playing.
Procedure Check the following potential causes:
2 5
Verify the operation of the projector
Reselect the proper Macro Button on with a Test Pattern.
1 3
the projector for the current movie.
Check all connections from the server.
6
Use the Test Pattern Button to select the
2
color bars test pattern. Ensure that red,
Restart the projector and the server, and
green and blue can all be seen properly in 7
try to play the movie again. Be sure to let
the test pattern.
the projector lamp cool down for at least
Reselect the proper Macro Button again, one minute prior to restarting.
3
for the current movie.
Restart the projector and the server, and try Problem: The image appears dim
4
to play the movie again. Be sure to let the 1
projector lamp cool down for at least one
Procedure Check the following potential causes:
minute prior to restarting.
3 On the Touch Panel, select the Control Tab and
1
press the "Service" button.
Problem: Colors do not appear correct, or the image is distorted On this page, increase lamp power by moving the
2 1
"Lamp Dimming" adjustment to the right, until
Procedure Check the following potential causes:
the “Current Light Output” value indicates 14FL.
Reselect the applicable Macro.
1 3 If the “Current Light Output” does not indicate
at least 11FL, contact the theater technician
Restart the projector and the server, and try
2
to play the movie again. Be sure to let the
projector lamp cool down for at least one
Problem: Projector indicates an overheating error
minute prior to restarting. 1
Procedure Check the following potential causes:
Problem: The projector tail lights are solid red
Check the booth’s ambient
1
Procedure Check the following potential causes: temperature, which must fall between: 2
• 50 - 95 degrees Fahrenheit
1 Restart the projector. If the tail lights turn • 10 – 35 degrees Celsius
green, the problem is resolved.
Check that the extraction system is
Check the Touch Panel for error 2 2
2 operating.
messages. If you find an error, report it
to the theater technician. Contact the theatre technician.
3
