Bellin Composite Wrapping

PT.SAHABAT INTI SEJAHTERA

Head Office: Branch Office:
Komp. Harapan Jaya Komp. Harapan Indah
Jl. Meranti I Blok A No. 28 Ruko Aralia Blok HY-43 No.29-30
Bekasi Utara 17124 Bekasi
Telp: 021-79186592, 79186595 Telp: 021-29253381
Fax: 021-79186594 Fax: 021-29253382
E-mail: admin@ptsis-Indonesia.com
Website: www.ptsis-indonesia.com
 TECHNICAL DATA SHEET
Bellin Composite Wrap is a composite system COMPOSITE WRAP CF PROPERTIES

BELLIN COMPOSITE WRAP

comprised of a Composite Wrap CF for Tensile Strength 470.000 psi (3.24 GPa)
mechanical protection and reinforcement inner
Wrap furnished impregnated with Composite Tensile Modulus 10.5 x 106 psi (72.4 GPa)
Wrap RE-RH system. Bellin Composite Wrap is
an odorless and nonflammable, durable, high Ultimate Elongation 4.5 %
strength material, impervious to fuels, Most
chemicals and solvents. It permanently bonds to Density 0.092 lbs./ in.3 (2.55 g/cm3)
a wide variety of surfaces such as metals,
composite, concrete, plastic and wood. It Weight per sq. yd. 14.9 oz. (505 g/m2)
provides strength in two directions, hoop and
transverse. Thickness 0.026 in (0.66 mm)

ASTM TYPICAL
PROPERTY DESIGN VALUE*
METHOD TEST VALUE

Ultimate tensile strength in primary 83,400 psi (575 Mpa) 66,720 psi ( 460 Mpa)
fiber direction, psi D-3039 (2.17 kip/iin. width) (1.7 kip/in. width)

Elogation at break D-3039 2.2 % 2.2%

Tensile Modulus, psi D-3039 3,750 x 10R psi (26.1 GPa) 3.03 x 10R psi (20.9 GPa)

Ultimate tensile strength 90 degrees 3,000 psi (20.7 Mpa)

D-3039 3,750 psi (25.8 Mpa)
to primary fibr, psi

COMPOSITE WRAP RE-RH PROPERTIES

ASTM TYPICAL
PROPERTY
METHOD TEST VALUE
BELLIN COMPOSITE WRAP

- Coating Tg 140oF (60oC)

1180O F (82OC)
Post cure (24 hours)

Thickness 0.2 mm
- Inner Composite Wrap
- Adhesive
ASTM D-63B 10.500 PSI
Tensile Strength1, psi
Type 1 (72.4 MPa)

- Outer Composite Wrap 461.000 psi

- Adhesive Tensile Modulus, psi
2000 µ

(3.18 GPa)

ASTM D-63B
Elongation Percent 5.0%
Type 1

17.900 psi
Flexural Strength, psi ASTM D-790
(123.4 MPa)

452.000 psi
- Finish Coating Flexural Modulus, psi ASTM D-790
(3.12 GPa)

1 Testing temperature: 70OF (21oC) Crosshead speed; 0.5 in. ( 13 mm ) / min.

Grips Instron 2716 0056 30 kips
* Specification values* can be* provided upon request
BELLIN COMPOSITE WRAP SYSTEM

* Bellin Composite Wrap System as a corrosion protection system is a multi-component system.

* Based upon blended Composite Wrap CF and Composite Wrap RE-RH materials provides unrivalled

BELLIN COMPOSITE WRAP

corrosion protection in terms of surface preparation requirements and ease of application.
* Idea for protecting pile against abrasion, harsh environmental conditions and external corrosion.
* Bellin Composite Wrap forms a chemical barrier that is resistant to a wide variety of chemical including
caustic dilute acids, salt solutions, water, steam, and petroleum solvents.
* It is a wet lay up system so it can be used on straight pile, as well as bends, tees and other
odd configurations. This system greatly reduces the periodic maintenance due to its extreme
durability.

Characteristics:
* Composite Wrap System consist of coating, inner CW with Adhesive,
Outer CW with Adhesive, and finish coating.
* Total Thickness : 2 mm (2000 µ)
* Continuous Operating Temperature: -51oC to 91oC
* Cure Time is approximately 8 hours at 29 oC
* Offers UV Protection
* Easy to apply
* Permanet adhesive
* Compatible with other coatings
* Patented Tecnology
* Cold applied

INSTALLATION PROCEDURE
* Perform surface preparation.
* Prime the area to be coated with Composite Wrap System
with totally thickness 2 mm (2000 µ)
* Apply the Composite Wrap using spiral wrap method.
BELLIN COMPOSITE WRAP

- Coating

- Inner Composite Wrap

- Adhesive

- Outer Composite Wrap

- Adhesive
2000 µ

- Finish Coating