®
ELECTRONICA
SCiCoreLink62E
scicorelink62E_i IGBT/MOSFET drivers
PRELIMINARY TECHNICAL INFORMATION
Adaptation board for SCiCoreDrive22
for econodual IGBT modules
DEFAULT VALUES (board configuration)
-Half Bridge mode (Direct Mode optional)
-4µS dead time between channels generated
-Gate resistor depending on the IGBT module used Foto no contractual / Photo non-contractual
-0-5V input PWM logic levels (0-15V optional)
-0-5V logic fault output
(low level-open collector output optional)
SCiCore Link62E is a printed circuit board specially designed for the driver module SCiCore Drive22. For
more accuracy information about the working of the entire driver board, consult the datasheet of the
SCiCore Drive22. Gate resistors are not included (by default). Configuration other than the default one is
available by order, in that case, please contact with us.
ELECTRICAL CHARACTERISTICS
Description symbol notes/test conditions Min Typ Max Units
Supply voltage VCC 14 15 16 V
PWM High state Input voltage VPWM_H 3,5 5 V
JP1&JP2 connected (1)
PWM Low state Input voltage VPWM_L 0 1,5 V
PWM High state Input voltage VPWM_H 11 15 V
JP1&JP2 unconnected (1)
PWM Low state Input voltage VPWM_L 0 4 V
Reset High state Input Voltage VRESET_H 2 5 V
Reset Low state Input Voltage VRESET_L 0 0,8 V
Fault open collector current IFAULT working as open collector 8 mA
Fault High state Output Voltage VFAULT_H working in logic level 5 V
indicates fault condition
Fault Low state Output Voltage VFAULT_L 0 0,4 V
open collector or logic level
101125Rev.:0
Note: JP1 and JP2 jumpers are located in the SCiCoreDrive22, not in SCiCoreLink62E
Reserves the right to change limits, test conditions and dimensions given in
this data sheet at any time without previous notice.
1
®
ELECTRONICA
scicorelink62E_i
CON 1 designation function JUMPERS
1 PWMTOP Input logic signal for switching TOP IGBT JP1 both connected: 5V logic level
2 GND Ground terminal for supply and logic signals JP2 both unconnected: 15V logic level
3 GND Ground terminal for supply and logic signals right connected: half bridge mode
JP3
4 RESET reset input signal (low state left connected: direct mode
5 GND Ground terminal for supply and logic signals
6 VCC +15VDC for supply voltage
conector CON1:
7 FAULT fault output signal type TYCO 1-1634688-0
8 VCC +15VDC for supply voltage
conector CON2:
9 VCC +15VDC for supply voltage type MOLEX 22-27-2021
10 PWMBOT Input logic signal for switching BOT IGBT
CON 2 designation function
1 NTC1 Terminal 1 for internal module NTC
2 NTC2 Terminal 2 for internal module NTC
HB
PWR
JP3 LED
DM
9 7 5 3 1
CON 1 assembly example
2 1
CON 2
10 8 6 4 2
All dimensions are in mm
101125Rev.:0
Reserves the right to change limits, test conditions and dimensions given in
this data sheet at any time without previous notice.
2
®
ELECTRONICA
scicorelink62E_i
Cost Effective Products
SEMICODE ELECTRONICA
offers to the market a comprehensive range of products from recognized manufacturers at the best price/
quality relationship, this products are provided with a basic reference code that allows maintaining the same
product reference even if the original device manufacturer is replaced. SEMICODE product reference has
to be considered as a generic brand.
Seeking the market needs and trends, we are constantly increasing the product portfolio with new products
and suppliers, please ask for the updated information available to our local contacts.
SEMICODE products include semiconductors, passive components and accessories focused in power
electronics market.
Datasheet Annotations:
SEMICODE ELECTRONICA annotate datasheets in the top left hard corner of the front page, to indicate
product status. The annotations are as follows:
Tentative information: This is the most tentative form of information and represents a very preliminary
specification. No actual design work on the product has been started.
Preliminary Information: The product is in design and development. The datasheet represents the product
as it is understood but details may change.
Advance Information: The product design is complete and final characterisation for volume production is
well in hand.
No Annotation: The product parameters are fixed and the product is available to datasheet specification.
NOTICE: The technical data are to specify components, not to guarantee their properties.No warranty or guarantee
expressed or implied is made regarding delivery or performance. The Company reserves the right to alter without prior notice the
specification of any product. Information concerning possible methods of use is provided as a guide only and does not constitute
any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user’s responsibility to fully
determine the performance and suitability of any equipment using such information and to ensure that any publication or data used
is up to date.
All brand names and product names used in this publication are trademarks, registered trademarks or trade names of their
respective owners.
101125Rev.:0
© SEMICODE ELECTRONICA 2008. TECHNICAL DOCUMENTATION – NOT FOR RESALE
Reserves the right to change limits, test conditions and dimensions given in
this data sheet at any time without previous notice.
