KIT - SAFETY DATA SHEET

Product identifier used on the

label:
Kit Nam e DEVCON® Epoxy Coat™ 7000 A R (A cid Resistant)
Stock No.: 12750

O ther m eans of identification:

Recom m ended use of the chem ical and restrictions on use:

Chem ical m anufacturer address and telephone num ber:

Manufacturer Nam e: ITW Perform ance Polym ers
Address: 30 Endicott Street
Danvers, MA 01923

Component list
Component A EPOXY COAT 7000 AR GREY RESIN
Component B ANCAMINE 2280 CURING AGENT
Kit SDS Revision Date 9/7/2015

Component A - SDS

SECTION 1 : IDENTIFICATION

Product identifier used on the label:

Product Nam e: EPOXY COA T 7000 A R GREY RESIN

O ther m eans of identification:

Synonym s: None.

Recom m ended use of the chem ical and restrictions on use:

Product Use/Restriction: Not applicable.

Chem ical m anufacturer address and telephone num ber:

Manufacturer Nam e: ITW
Address: 30 Endicott Street
Danvers, MA 01923
General Phone Num ber: (978) 777-1100

Em ergency phone num ber:

Em ergency Phone Num ber: (800) 424-9300
CHEMTREC: For em ergencies in the US, call CHEMTREC: 800-424-9300

SECTION 2 : HAZARD(S) IDENTIFICATION

Classification of the chem ical in accordance with CFR 1910.1200(d)(f):

GHS Pictogram s:

Signal W ord: W ARNING.

GHS Class: Sk in Sensitization. category 1.
Hazard Statem ents: H317 - May cause an allergic sk in reaction.
Precautionary Statem ents: P261 - Avoid breathing dust/fum e/gas/m ist/vapours/spray.
P272 - Contam inated work clothing should not be allowed out of the work place.
P280 - W ear protective gloves/protective clothing/eye protection/face protection.
P302+P352 - IF O N SKIN: W ash with plenty of water.
P321 - Specific treatm ent (see ... on this label).
P333+P313 - If sk in irritation or rash occurs: Get m edical advice/attention.
P362+P364 - Tak e off contam inated clothing and wash it before reuse.
P501 - Dispose of contents/container in accordance with Local, State, Federal and Provincial regulations.

DEVCON® Epoxy Coat™ 7000 AR (Acid Resistant) Stock No. 12750

Revision:: 9/7/2015
Page 1 of 11
 Hazards not otherwise classified that have been identified during the classification process:

Route of Ex posure: Eyes. Sk in. Inhalation. Ingestion.

Potential Health Effects:
Eye: Can cause m oderate irritation, burning sensation, tearing, redness, and swelling. O verex posure m ay
cause lacrim ation, conjunctivitis, corneal dam age and perm anent injury.

Sk in: Can cause sk in irritation; itching, redness, rashes, hives, burning, and swelling. Allergic reactions are
possible.
May cause sk in sensitization, an allergic reaction, which becom es evident on reex posure to this
m aterial.

Inhalation: Respiratory tract irritant. High concentration m ay cause dizziness, headache, and anesthetic effects.
Ingestion: Causes irritation, a burning sensation of the m outh, throat and gastrointestinal tract and abdom inal
pain.
Chronic Health Effects: Prolonged sk in contact m ay lead to burning associated with severe reddening, swelling, and possible
tissue destruction.
Signs/Sym ptom s: O verex posure can cause headaches, dizziness, nausea, and vom iting.
Target O rgans: Eyes. Sk in. Respiratory system . Digestive system .

Aggravation of Pre-Ex isting Individuals with pre-ex isting sk in disorders, asthm a, allergies or k nown sensitization m ay be m ore
Conditions: susceptible to the effects of this product.

SECTION 3 : COMPOSITION/INFORMATION ON INGREDIENTS

Mix tures:
Chemical Name CA S# Ingredient Percent EC Num.

Phenol, polym er with form aldehyde, glycidyl ether 28064-14-4 90 - 100 by weight

Bisphenol A diglycidyl ether resin 25068-38-6 1 - 10 by weight

Titanium diox ide 13463-67-7 1 - 10 by weight

Am orphous silicon diox ide 67762-90-7 0.1 - 1.0 by weight

SECTION 4 : FIRST AID MEASURES

Description of necessary m easures:

Eye Contact: Im m ediately flush eyes with plenty of water for at least 15 to 20 m inutes. Ensure adequate flushing of
the eyes by separating the eyelids with fingers. Get im m ediate m edical attention.
Sk in Contact: Im m ediately wash sk in with plenty of soap and water for 15 to 20 m inutes, while rem oving
contam inated clothing and shoes. Get m edical attention if irritation develops or persists.
Inhalation: If inhaled, rem ove to fresh air. If not breathing, give artificial respiration or give ox ygen by trained
personnel. Seek im m ediate m edical attention.
Ingestion: If swallowed, do NO T induce vom iting. Call a physician or poison control center im m ediately. Never give
anything by m outh to an unconscious person.

SECTION 5 : FIRE FIGHTING MEASURES

Suitable and unsuitable ex tinguishing m edia:

Suitable Ex tinguishing Media: Use carbon diox ide (CO 2) or dry chem ical when fighting fires involving this m aterial.

Unsuitable ex tinguishing m edia: W ater or foam m ay cause frothing.

Unusual Fire Hazards: Sealed containers at elevated tem peratures m ay rupture ex plosively and spread fire due to
polym erization. Heating above 300 deg F in the presence of air m ay cause slow ox idative
decom position and above 500 deg F m ay cause polym erization.

Special protective equipm ent and precautions for fire-fighters:

Protective Equipm ent: As in any fire, wear Self-Contained Breathing Apparatus (SCBA), MSHA/NIO SH (approved or equivalent)
and full protective gear.
Fire Fighting Instructions: Evacuate area of unprotected personnel. Use cold water spray to cool fire ex posed containers to
m inim ize risk of rupture. Do not enter confined fire space without full protective gear. If possible,
contain fire run-off water.

SECTION 6 : ACCIDENTAL RELEASE MEASURES

DEVCON® Epoxy Coat™ 7000 AR (Acid Resistant) Stock No. 12750

Revision:: 9/7/2015
Page 2 of 11
 Personal precautions, protective equipm ent and em ergency procedures:

Personal Precautions: Evacuate area and k eep unnecessary and unprotected personnel from entering the spill area.

Environm ental precautions:

Environm ental Precautions: Avoid runoff into storm sewers, ditches, and waterways.

Methods and m aterials for containm ent and cleaning up:

Spill Cleanup Measures: Absorb spill with inert m aterial (e,g., dry sand or earth), then place in a chem ical waste container.
Provide ventilation. Clean up spills im m ediately observing precautions in the protective equipm ent
section. After rem oval, flush spill area with soap and water to rem ove trace residue.
Avoid personal contact and breathing vapors or m ists. Ventilate area. Use proper personal protective
equipm ent as listed in Section 8.

Reference to other sections:

O ther Precautions: Pum p or shovel to storage/salvage vessels.

SECTION 7 : HANDLING and STORAGE

Precautions for safe handling:

Handling: Use with adequate ventilation. Avoid breathing vapor, aerosol or m ist.

Hygiene Practices: W ash thoroughly after handling.

Special Handling Procedures: Provide appropriate ventilation/respiratory protection against decom position products (see Section 10)
during welding/flam e cutting operations and to protect against dust during sanding/grinding of cured
product.

Conditions for safe storage, including any incom patibilities:

Storage: Store in a cool, dry, well ventilated area away from sources of heat and incom patible m aterials. Keep
container tightly closed when not in use.

SECTION 8: EXPOSURE CONTROLS, PERSONAL PROTECTION

EXPO SURE GUIDELINES:

Titanium dioxide :
Guideline ACGIH: TLV-TW A: 10 m g/m 3
Appropriate engineering controls:

Engineering Controls: Use appropriate engineering control such as process enclosures, local ex haust ventilation, or other
engineering controls to control airborne levels below recom m ended ex posure lim its. Good general
ventilation should be sufficient to control airborne levels. W here such system s are not effective wear
suitable personal protective equipm ent, which perform s satisfactorily and m eets O SHA or other
recognized standards. Consult with local procedures for selection, training, inspection and m aintenance
of the personal protective equipm ent.

Individual protection m easures:

Eye/Face Protection: W ear appropriate protective glasses or splash goggles as described by 29 CFR 1910.133, O SHA eye
and face protection regulation, or the European standard EN 166.

Sk in Protection Description: W ear appropriate protective gloves and other protective apparel to prevent sk in contact. Consult
m anufacturer's data for perm eability data.
Respiratory Protection: A NIO SH approved air-purifying respirator with an organic vapor cartridge or canister m ay be
perm issible under certain circum stances where airborne concentrations are ex pected to ex ceed
ex posure lim its. Protection provided by air purifying respirators is lim ited. Use a positive pressure air
supplied respirator if there is any potential for an uncontrolled release, ex posure levels are not k nown,
or any other circum stances where air purifying respirators m ay not provide adequate protection.
O ther Protective: Facilities storing or utilizing this m aterial should be equipped with an eyewash and a deluge shower
safety station.

Notes : O nly established PEL and TLV values for the ingredients are listed.

SECTION 9 : PHYSICAL and CHEMICAL PROPERTIES

PHYSICAL AND CHEMICAL PRO PERTIES:

Physical State Appearance: Liquid.

Color: Gray

O dor: Slight. odor.

Boiling Point: >500°F (260°C)
Melting Point: Not determ ined.

Specific Gravity: 1.17

Solubility: negligible.
Vapor Density: >1 (air = 1)
Vapor Pressure: 0.03 m m Hg @171°F

Percent Volatile: 0

DEVCON® Epoxy Coat™ 7000 AR (Acid Resistant) Stock No. 12750

Revision:: 9/7/2015
Page 3 of 11
 Evaporation Rate: <<1 (butyl acetate = 1)
pH: Neutral.

Molecular Form ula: Mix ture

Molecular W eight: Mix ture
Flash Point: >400°F (204.4°C)

Flash Point Method: Pensk y-Martens Closed Cup

Lower Flam m able/Ex plosive Lim it: Not determ ined.
Upper Flam m able/Ex plosive Lim it: Not determ ined.
Auto Ignition Tem perature: Not determ ined.

VO C Content: 0 g/L

9.2. O ther inform ation:

Percent Solids by W eight 100

SECTION 10 : STABILITY and REACTIVITY

Chem ical Stability:

Chem ical Stability: Stable under norm al tem peratures and pressures.
Possibility of hazardous reactions:

Hazardous Polym erization: Not reported.

Conditions To Avoid:
Conditions to Avoid: Ex trem e heat, spark s, and open flam e. Incom patible m aterials, ox idizers and ox idizing conditions.
Heating resin above 300 F in the presence of air m ay cause slow ox idative decom position.
Incom patible Materials:

Incom patible Materials: Strong Lewis or m ineral acids, strong ox idizing agents, strong m ineral and organic bases (especially
prim ary and secondary aliphatic am ines).

SECTION 11 : TOXICOLOGICAL INFORMATION

TO XICO LO GICAL INFO RMATIO N:

Bisphenol A diglycidyl ether resin :

Eye: Adm inistration into the eye - Rabbit Standard Draize test: 100 m g [Mild]
Adm inistration into the eye - Rabbit Standard Draize test: 20 m g/24H [Moderate]
Adm inistration into the eye - Rabbit Standard Draize test: 5 m g/24H [Severe] (RTECS)
Sk in: Adm inistration onto the sk in - Rabbit LD50 - Lethal dose, 50 percent k ill: >20 m L/k g [Details of tox ic
effects not reported other than lethal dose value]
Adm inistration onto the sk in - Rat LD50 - Lethal dose, 50 percent k ill: >1200 m g/k g [Details of tox ic
effects not reported other than lethal dose value] (RTECS)

Ingestion: O ral - Rat LD50 - Lethal dose, 50 percent k ill: 10700 uL/k g [Details of tox ic effects not reported other
than lethal dose value]
O ral - Rat LD50 - Lethal dose, 50 percent k ill: 13600 m g/k g [Behavioral - Som nolence (general
depressed activity) Lungs, Thorax , or Respiration - Dyspnea Nutritional and Gross Metabolic - W eight
loss or decreased weight gain]
O ral - Rat LD50 - Lethal dose, 50 percent k ill: 13.6 gm /k g [Details of tox ic effects not reported other
than lethal dose value]
O ral - Rat LD50 - Lethal dose, 50 percent k ill: 11.4 gm /k g [Details of tox ic effects not reported other
than lethal dose value]
O ral - Rat LD50 - Lethal dose, 50 percent k ill: 30 gm /k g [Behavioral - Som nolence (general depressed
activity) Lungs, Thorax , or Respiration - Dyspnea Nutritional and Gross Metabolic - W eight loss or
decreased weight gain]
O ral - Rat LD50 - Lethal dose, 50 percent k ill: 30 gm /k g [Details of tox ic effects not reported other
than lethal dose value]
O ral - Rat LD50 - Lethal dose, 50 percent k ill: >1 gm /k g [Details of tox ic effects not reported other
than lethal dose value]
O ral - Rat LD50 - Lethal dose, 50 percent k ill: 11400 m g/k g [Behavioral - Som nolence (general
depressed activity) Lungs, Thorax , or Respiration - Dyspnea Nutritional and Gross Metabolic (RTECS)
Titanium dioxide :
Chronic Effects: Norm al application procedures for this product pose m inim al hazard as to the release of respirable
titanium diox ide dust, but grinding or sanding dried film s of this product m ay yield som e respirable
titanium diox ide. Although IARC has classified titanium diox ide as possible carcinogenic to hum an
(2B), their sum m ary concludes: "No significant ex posure to titanium diox ide is thought to occur during
the use of products which titanium diox ide is bound to other m aterials". O SHA does not regulate
titanium diox ide as a carcinogen. However, under 29CFR 1910.1200 the SDS m ust convey the fact that
titanium diox ide is a potential carcinogen to rats.
Carcinogenicity: Anim al evidence shows that high concentrations of pigm ent-grade (powdered) and ultrafine titanium
diox ide dust caused respiratory tract cancer in rats ex posed by inhalation.

SECTION 12 : ECOLOGICAL INFORMATION

Ecotox icity:

DEVCON® Epoxy Coat™ 7000 AR (Acid Resistant) Stock No. 12750

Revision:: 9/7/2015
Page 4 of 11
 Ecotox icity: No ecotox icity data was found for the product.

Environm ental Fate: No environm ental inform ation found for this product.

SECTION 13 : DISPOSAL CONSIDERATIONS

Description of waste:

W aste Disposal: Consult with the US EPA Guidelines listed in 40 CFR Part 261.3 for the classifications of hazardous
waste prior to disposal. Furtherm ore, consult with your state and local waste requirem ents or guidelines,
if applicable, to ensure com pliance. Arrange disposal in accordance to the EPA and/or state and local
guidelines.
RCRA Num ber: Not determ ined.

SECTION 14 : TRANSPORT INFORMATION

DO T Shipping Nam e: Refer to Bill of Lading

DO T UN Num ber: Refer to Bill of Lading

IATA Shipping Nam e: Refer to Bill of Lading

IATA UN Num ber: Refer to Bill of Lading

IMDG UN Num ber : Refer to Bill of Lading

IMDG Shipping Nam e : Refer to Bill of Lading

SECTION 15 : REGULATORY INFORMATION

Safety, health and environm ental regulations specific for the product:

Phenol, polymer with formaldehyde, glycidyl ether :

TSCA Inventory Status: Listed

Canada DSL: Listed

Bisphenol A diglycidyl ether resin :
TSCA Inventory Status: Listed

Canada DSL: Listed

Titanium dioxide :
TSCA Inventory Status: Listed
Canada DSL: Listed

A morphous silicon dioxide :

TSCA Inventory Status: Listed
Canada DSL: Listed

Canadian Regulations. W HMIS Hazard Class(es): D2B

W HMIS Pictogram s:

SECTION 16 : ADDITIONAL INFORMATION

HMIS Ratings:

HMIS Health Hazard: 2* Health Hazard 2*

HMIS Fire Hazard: 1 Fire Hazard 1
HMIS Reactivity: 1 Reactivity 1
HMIS Personal Protection: X Personal Protection X
* Chronic Health Effects

SDS Revision Date: March 17, 2015

SDS Revision Notes: GHS Update
SDS Form at: In accordance to O SHA GHS 1910.1200
SDS Author: Actio Corporation

DEVCON® Epoxy Coat™ 7000 AR (Acid Resistant) Stock No. 12750

Revision:: 9/7/2015
Page 5 of 11
 Disclaim er: The inform ation in this Safety Data Sheet (SDS) is believed to be correct as of the date issued. ITW
Perform ance Polym ers MAKES NO W ARRANTIES, EXPRESSED O R IMPLIED, INCLUDING, BUT NO T LIMITED
TO , ANY IMPLIED W ARRANTY O F MERCHANTABILITY O R FITNESS FO R A PARTICULAR PURPO SE O R
CO URSE O F PERFO RMANCE O R USAGE O F TRADE. User is responsible for determ ining whether the ITW
Perform ance Polym ers product is fit for a particular purpose and suitable for user's m ethod of use or
application. Given the variety of factors that can affect the use and application of a ITW Perform ance
Polym ers product, som e of which are uniquely within the user's k nowledge and control, it is essential
that the user evaluate the ITW Perform ance Polym ers product to determ ine whether it is fit for a
particular purpose and suitable for user's m ethod of use or application. ITW Perform ance Polym ers
provides inform ation in electronic form as a service to its custom ers. Due to the rem ote possibility that
electronic transfer m ay have resulted in errors, om issions or alterations in this inform ation, ITW
Perform ance Polym ers m ak es no representations as to its com pleteness or accuracy. In addition,
inform ation obtained from a database m ay not be as current as the inform ation in the MSDS available
directly from ITW Perform ance Polym ers.

Copyright© 1996-2018 Enviance. All Rights Reserved.

Component B - SDS
SECTION 1 : IDENTIFICATION

Product identifier used on the label:

Product Nam e: A NCA MINE 2280 CURING A GENT

O ther m eans of identification:

Recom m ended use of the chem ical and restrictions on use:

Chem ical m anufacturer address and telephone num ber:

Manufacturer Nam e: ITW
Address: 30 Endicott Street
Danvers, MA 01923
General Phone Num ber: (978) 777-1100

Em ergency phone num ber:

Em ergency Phone Num ber: (800) 424-9300
CHEMTREC: For em ergencies in the US, call CHEMTREC: 800-424-9300

SECTION 2 : HAZARD(S) IDENTIFICATION

Classification of the chem ical in accordance with CFR 1910.1200(d)(f):

GHS Pictogram s:

Signal W ord: DANGER.

GHS Class: Serious Eye Dam age. category 1.
Specific Target O rgan Tox icity -STO T Repeated ex posure RE. Category 2 (O ral).
Sk in Irritation. Category 2.
Sk in Sensitization. category 1.
Acute O ral Tox icity. Category 4.
Hazard Statem ents: H318 - Causes serious eye dam age.
H373 - May cause dam age to organs through prolonged or repeated ex posure.
H315 - Causes sk in irritation.
H317 - May cause an allergic sk in reaction.
H302 - Harm ful if swallowed.

Precautionary Statem ents: P260 - Do not breathe dust/fum e/gas/m ist/vapours/spray.

P261 - Avoid breathing dust/fum e/gas/m ist/vapours/spray.
P264 - W ash hands thoroughly after handling.
P270 - Do not eat, drink or sm ok e when using this product.
P272 - Contam inated work clothing should not be allowed out of the work place.
P280 - W ear protective gloves/protective clothing/eye protection/face protection.
P301+P312 - IF SW ALLO W ED: Call a PO ISO N CENTER or doctor/physician if you feel unwell.
P302+P352 - IF O N SKIN: W ash with plenty of water.
P305+P351+P338 - IF IN EYES: Rinse cautiously with water for several m inutes. Rem ove contact lenses,
if present and easy to do. Continue rinsing.
P310 - Im m ediately call a PO ISO N CENTER or doctor/physician.
P314 - Get m edical advice/attention if you feel unwell.
P321 - Specific treatm ent (see ... on this label).
P330 - Rinse m outh.
P332+P313 - If sk in irritation occurs: Get m edical advice/attention.
P333+P313 - If sk in irritation or rash occurs: Get m edical advice/attention.
P362+P364 - Tak e off contam inated clothing and wash it before reuse.
P501 - Dispose of contents/container in accordance with Local, State, Federal and Provincial regulations.

Hazards not otherwise classified that have been identified during the classification process:

Route of Ex posure: Eyes. Sk in. Inhalation. Ingestion.

Potential Health Effects:

DEVCON® Epoxy Coat™ 7000 AR (Acid Resistant) Stock No. 12750

Revision:: 9/7/2015
Page 6 of 11
 Acute Health Effects: Com ponents of the product m ay affect the nervous system

Eye: Can cause severe eye irritation and burns. Eye contact m ay cause perm anent dam age or blindness.

Sk in: Causes severe sk in irritation. May cause perm anent sk in dam age. Allergic reactions are possible.
May cause sk in sensitization, an allergic reaction, which becom es evident on reex posure to this
m aterial.

Inhalation: Vapor or m ist m ay cause severe respiratory system irritation.

Ingestion: Causes irritation, a burning sensation of the m outh, throat and gastrointestinal tract and abdom inal
pain.
Chronic Health Effects: Prolonged sk in contact m ay lead to burning associated with severe reddening, swelling, and possible
tissue destruction.

Signs/Sym ptom s: Neurological disorders Eye disease. Sk in disorders and Allergies

Target O rgans: Eyes. Sk in. Respiratory system . Digestive system .

Aggravation of Pre-Ex isting Individuals with pre-ex isting sk in disorders, asthm a, allergies or k nown sensitization m ay be m ore
Conditions: susceptible to the effects of this product.

SECTION 3 : COMPOSITION/INFORMATION ON INGREDIENTS

Mix tures:

Chemical Name CA S# Ingredient Percent EC Num.

Methyleneox ide, polym er with benzenam ine, hydrogenated 135108-88-2 40 - 50 by weight

Benzyl alcohol 100-51-6 40 - 50 by weight

O rganic acid No Data 1 - 10 by weight

4,4'-Methylenebiscyclohex anam ine 1761-71-3 1 - 10 by weight

SECTION 4 : FIRST AID MEASURES

Description of necessary m easures:

Eye Contact: Im m ediately flush eyes with plenty of water for at least 15 to 20 m inutes. Ensure adequate flushing of
the eyes by separating the eyelids with fingers. Get im m ediate m edical attention.
Sk in Contact: Im m ediately wash sk in with plenty of soap and water for 15 to 20 m inutes, while rem oving
contam inated clothing and shoes. Get m edical attention if irritation develops or persists.

Inhalation: If inhaled, rem ove to fresh air. If not breathing, give artificial respiration or give ox ygen by trained
personnel. Seek im m ediate m edical attention.
Ingestion: If swallowed, do NO T induce vom iting. Call a physician or poison control center im m ediately. Never give
anything by m outh to an unconscious person.

Most im portant sym ptom s/effects, acute and delayed:

O ther First Aid: Neurological disorders Eye disease. Sk in disorders and Allergies.

SECTION 5 : FIRE FIGHTING MEASURES

Suitable and unsuitable ex tinguishing m edia:

Suitable Ex tinguishing Media: Use carbon diox ide (CO 2) or dry chem ical when fighting fires involving this m aterial.

Unsuitable ex tinguishing m edia: W ater or foam m ay cause frothing.

Specific hazards arising from the chem ical:

Hazardous Com bustion Incom plete com bustion m ay form carbon m onox ide. May generate am m onia gas. May generate tox ic
Byproducts: nitrogen ox ide gases. Burning produces nox ious and tox ic fum es. Downwind personnel m ust be
evacuated.

Special protective equipm ent and precautions for fire-fighters:

Protective Equipm ent: As in any fire, wear Self-Contained Breathing Apparatus (SCBA), MSHA/NIO SH (approved or equivalent)
and full protective gear.
Fire Fighting Instructions: Evacuate area of unprotected personnel. Use cold water spray to cool fire ex posed containers to
m inim ize risk of rupture. Do not enter confined fire space without full protective gear. If possible,
contain fire run-off water.

DEVCON® Epoxy Coat™ 7000 AR (Acid Resistant) Stock No. 12750

Revision:: 9/7/2015
Page 7 of 11
SECTION 6 : ACCIDENTAL RELEASE MEASURES

Personal precautions, protective equipm ent and em ergency procedures:

Personal Precautions: Evacuate area and k eep unnecessary and unprotected personnel from entering the spill area.
Environm ental precautions:

Environm ental Precautions: Avoid runoff into storm sewers, ditches, and waterways.

Methods and m aterials for containm ent and cleaning up:

Spill Cleanup Measures: Absorb spill with inert m aterial (e,g., dry sand or earth), then place in a chem ical waste container.
Provide ventilation. Clean up spills im m ediately observing precautions in the protective equipm ent
section. After rem oval, flush spill area with soap and water to rem ove trace residue.
Avoid personal contact and breathing vapors or m ists. Ventilate area. Use proper personal protective
equipm ent as listed in Section 8.

Reference to other sections:

O ther Precautions: Pum p or shovel to storage/salvage vessels.

SECTION 7 : HANDLING and STORAGE

Precautions for safe handling:

Handling: Use with adequate ventilation. Avoid breathing vapor, aerosol or m ist.

Hygiene Practices: W ash thoroughly after handling.

Special Handling Procedures: Provide appropriate ventilation/respiratory protection against decom position products (see Section 10)
during welding/flam e cutting operations and to protect against dust during sanding/grinding of cured
product.

Conditions for safe storage, including any incom patibilities:

Storage: Store in a cool, dry, well ventilated area away from sources of heat and incom patible m aterials. Keep
container tightly closed when not in use. Do not store in reactive m etal containers. Keep away from
acids, ox idizers. Keep away from alk alis.

SECTION 8: EXPOSURE CONTROLS, PERSONAL PROTECTION

EXPO SURE GUIDELINES:

Appropriate engineering controls:

Engineering Controls: Use appropriate engineering control such as process enclosures, local ex haust ventilation, or other
engineering controls to control airborne levels below recom m ended ex posure lim its. Good general
ventilation should be sufficient to control airborne levels. W here such system s are not effective wear
suitable personal protective equipm ent, which perform s satisfactorily and m eets O SHA or other
recognized standards. Consult with local procedures for selection, training, inspection and m aintenance
of the personal protective equipm ent.

Individual protection m easures:

Eye/Face Protection: W ear appropriate protective glasses or splash goggles as described by 29 CFR 1910.133, O SHA eye
and face protection regulation, or the European standard EN 166.

Sk in Protection Description: W ear appropriate protective gloves and other protective apparel to prevent sk in contact. Consult
m anufacturer's data for perm eability data.
Hand Protection Description: Butyl rubber.; Nitrile rubber., Neoprene gloves.; Im pervious gloves; PVC disposable gloves.

Respiratory Protection: A NIO SH approved air-purifying respirator with an organic vapor cartridge or canister m ay be
perm issible under certain circum stances where airborne concentrations are ex pected to ex ceed
ex posure lim its. Protection provided by air purifying respirators is lim ited. Use a positive pressure air
supplied respirator if there is any potential for an uncontrolled release, ex posure levels are not k nown,
or any other circum stances where air purifying respirators m ay not provide adequate protection.

O ther Protective: Facilities storing or utilizing this m aterial should be equipped with an eyewash and a deluge shower
safety station.

Notes : O nly established PEL and TLV values for the ingredients are listed.

SECTION 9 : PHYSICAL and CHEMICAL PROPERTIES

PHYSICAL AND CHEMICAL PRO PERTIES:

Physical State Appearance: Liquid.

Color: Am ber.
O dor: Am ine.

Boiling Point: 432°F (222.2°C)

Melting Point: Not determ ined.

Specific Gravity: 1.06

Solubility: SLIGHT (0.1-1%)

DEVCON® Epoxy Coat™ 7000 AR (Acid Resistant) Stock No. 12750

Revision:: 9/7/2015
Page 8 of 11
 Vapor Density: Not determ ined.

Vapor Pressure: 0.7 m m Hg @70°F

Percent Volatile: Not determ ined.

Evaporation Rate: Not determ ined.

pH: alk aline

Molecular Form ula: Mix ture

Molecular W eight: Mix ture

Flash Point: 219°F (103.8°C)

Flash Point Method: closed cup.

Lower Flam m able/Ex plosive Lim it: Not determ ined.

Upper Flam m able/Ex plosive Lim it: Not determ ined.

Auto Ignition Tem perature: Not determ ined.

VO C Content: Not determ ined.

9.2. O ther inform ation:

Percent Solids by W eight Not determ ined.

SECTION 10 : STABILITY and REACTIVITY

Chem ical Stability:

Chem ical Stability: Stable under norm al tem peratures and pressures.

Possibility of hazardous reactions:

Hazardous Polym erization: Not reported.

Conditions To Avoid:

Conditions to Avoid: Ex trem e heat, spark s, and open flam e. Incom patible m aterials, ox idizers and ox idizing conditions.
Incom patible Materials:

Incom patible Materials: Incom patible with O x idizing agents, reducing agents Am ines, bases, bases, Reactive m etals (e.g.
sodium , calcium , zinc etc.), organic acids (i.e. acetic acid, citric acid etc.), m ineral acids, and m aterials
reactive with hydrox yl com pounds.
CAUTIO N! N-Nitrosam ines, m any of which are k nown to be potent carcinogens, m ay be form ed when
the product com es in contact with nitrous acid, nitrites or atm ospheres with high nitrous ox ide
concentrations. Nitrous acid and other nitrosating agents.

Hazardous Decom position Products:

Special Decom position Products: O x ides of carbon and nitrogen; Nitrogen ox ide can react with water vapors to form corrosive nitric acid..
Nitric acid . Am m onia . Aldehydes. Flam m able hydrocarbon fragm ents.. Nitrosam ine.. O rganic acid
vapors.

SECTION 11 : TOXICOLOGICAL INFORMATION

TO XICO LO GICAL INFO RMATIO N:

Benzyl alcohol :

Sk in: Adm inistration onto the sk in - Rabbit LD50 - Lethal dose, 50 percent k ill: 2000 m g/k g [Details of tox ic
effects not reported other than lethal dose value] (RTECS)

Inhalation: Inhalation - Rat LC50 - Lethal concentration, 50 percent k ill: >500 m g/m 3 [Behavioral - Som nolence
(general depressed activity) Behavioral - Atax ia Lungs, Thorax , or Respiration - Respiratory
depression] (RTECS)

Ingestion: O ral - Rat LD50 - Lethal dose, 50 percent k ill: 1230 m g/k g [Behavioral - Som nolence (general
depressed activity) Behavioral - Ex citem ent Behavioral - Com a]
O ral - Rat LD50 - Lethal dose, 50 percent k ill: 1660 m g/k g [Behavioral - Som nolence (general
depressed activity) Behavioral - Atax ia Lungs, Thorax , or Respiration - Respiratory depression]
O ral - Rat LD50 - Lethal dose, 50 percent k ill: 1.5 m L/k g [Details of tox ic effects not reported other
than lethal dose value] (RTECS)

4,4'-Methylenebiscyclohexanamine :
Eye: Adm inistration into the eye - Rabbit Standard Draize test: 10 uL/24H [Severe] (RTECS)

SECTION 12 : ECOLOGICAL INFORMATION

Ecotox icity:

Ecotox icity: No ecotox icity data was found for the product.
Environm ental Fate: No environm ental inform ation found for this product.

SECTION 13 : DISPOSAL CONSIDERATIONS

DEVCON® Epoxy Coat™ 7000 AR (Acid Resistant) Stock No. 12750
Revision:: 9/7/2015
Page 9 of 11
 Description of waste:

W aste Disposal: Consult with the US EPA Guidelines listed in 40 CFR Part 261.3 for the classifications of hazardous
waste prior to disposal. Furtherm ore, consult with your state and local waste requirem ents or guidelines,
if applicable, to ensure com pliance. Arrange disposal in accordance to the EPA and/or state and local
guidelines.

RCRA Num ber: Not determ ined.

SECTION 14 : TRANSPORT INFORMATION

DO T Shipping Nam e: Refer to Bill of Lading

DO T UN Num ber: Refer to Bill of Lading

IATA Shipping Nam e: Refer to Bill of Lading

IATA UN Num ber: Refer to Bill of Lading

IMDG UN Num ber : Refer to Bill of Lading

IMDG Shipping Nam e : Refer to Bill of Lading

SECTION 15 : REGULATORY INFORMATION

Safety, health and environm ental regulations specific for the product:

Methyleneoxide, polymer with benzenamine, hydrogenated :

TSCA Inventory Status: Listed

Canada DSL: Listed

Benzyl alcohol :

TSCA Inventory Status: Listed

Canada DSL: Listed

4,4'-Methylenebiscyclohexanamine :

TSCA Inventory Status: Listed

Canada DSL: Listed

Canadian Regulations. W HMIS Hazard Class(es): D2B

All com ponents of this product are on the Canadian Dom estic Substances List.
W HMIS Pictogram s:

SECTION 16 : ADDITIONAL INFORMATION

HMIS Ratings:

HMIS Health Hazard: 2* Health Hazard 2*

HMIS Fire Hazard: 1 Fire Hazard 1
HMIS Reactivity: 0 Reactivity 0
HMIS Personal Protection: X Personal Protection X
* Chronic Health Effects

SDS Revision Date: June 29, 2015

SDS Revision Notes: GHS Update

SDS Form at: In accordance to O SHA GHS 1910.1200

SDS Author: Actio Corporation

Disclaim er: The inform ation in this Safety Data Sheet (SDS) is believed to be correct as of the date issued. ITW
Perform ance Polym ers MAKES NO W ARRANTIES, EXPRESSED O R IMPLIED, INCLUDING, BUT NO T LIMITED
TO , ANY IMPLIED W ARRANTY O F MERCHANTABILITY O R FITNESS FO R A PARTICULAR PURPO SE O R
CO URSE O F PERFO RMANCE O R USAGE O F TRADE. User is responsible for determ ining whether the ITW
Perform ance Polym ers product is fit for a particular purpose and suitable for user's m ethod of use or
application. Given the variety of factors that can affect the use and application of a ITW Perform ance
Polym ers product, som e of which are uniquely within the user's k nowledge and control, it is essential
that the user evaluate the ITW Perform ance Polym ers product to determ ine whether it is fit for a
particular purpose and suitable for user's m ethod of use or application. ITW Perform ance Polym ers
provides inform ation in electronic form as a service to its custom ers. Due to the rem ote possibility that
electronic transfer m ay have resulted in errors, om issions or alterations in this inform ation, ITW
Perform ance Polym ers m ak es no representations as to its com pleteness or accuracy. In addition,
inform ation obtained from a database m ay not be as current as the inform ation in the MSDS available
directly from ITW Perform ance Polym ers.

Copyright© 1996-2018 Enviance. All Rights Reserved.

DEVCON® Epoxy Coat™ 7000 AR (Acid Resistant) Stock No. 12750

Revision:: 9/7/2015
Page 10 of 11
DEVCON® Epoxy Coat™ 7000 AR (Acid Resistant) Stock No. 12750
Revision:: 9/7/2015
Page 11 of 11