FZ10-PP.

book 1 ページ ２００３年１１月１８日 火曜日 午後１時７分

Digital Camera
Operating Instructions

Model No. DMC-FZ10PP

Before use, please read these

instructions completely.

For USA assistance, please call: 1-800-272-7033 or send e-mail to : digitalstillcam@panasonic.com

For Canadian assistance, please call: 1-800-561-5505 or visit us at www.panasonic.ca

VQT0F85-2
FZ10-PP.book 2 ページ ２００３年１１月１８日 火曜日 午後１時７分

Safety
Safety

Dear Customer, Carefully observe copyright laws.

We would like to take this opportunity to Recording of pre-recorded tapes or
thank you for purchasing this Panasonic discs or other published or
Digital Camera. Please read these broadcast material for purposes
Operating Instructions carefully and other than your own private use may
keep them handy for future reference. infringe copyright laws. Even for the
purpose of private use, recording of
certain material may be restricted.
Information for Your
Safety • Please note that the actual controls
and components, menu items, etc. of
your Digital Camera may look
WARNING somewhat different from those shown
TO REDUCE THE RISK OF FIRE in the illustrations in these Operating
OR SHOCK HAZARD AND Instructions.
ANNOYING INTERFERENCE, USE • SD Logo is a trademark.
ONLY THE RECOMMENDED • Other names, company names, and
ACCESSORIES AND DO NOT product names printed in these
EXPOSE THIS EQUIPMENT TO instructions are trademarks or
RAIN OR MOISTURE. DO NOT registered trademarks of the
REMOVE THE COVER (OR BACK); companies concerned.
THERE ARE NO USER
SERVICEABLE PARTS INSIDE. THE SOCKET OUTLET SHALL BE
REFER SERVICING TO QUALIFIED INSTALLED NEAR THE
SERVICE PERSONNEL. EQUIPMENT AND SHALL BE
EASILY ACCESSIBLE.

Notice:
This product has parts that contain a
small amount of mercury. It also CAUTION
contains lead in some components. Danger of explosion if battery is
Disposal of these materials may be incorrectly replaced. Replace only
regulated in your community due to with the same or equivalent type
environmental considerations. For recommended by the manufacturer.
disposal or recycling information Dispose of used batteries according
please contact your local authorities, to the manufacturer’s instructions.
or the Electronics Industries
Alliance: <http://www.eiae.org.>

RBRC A lithium ion/polymer battery that is recyclable powers the

TM
product you have purchased. Please call 1-800-8-BATTERY
Li-ion
for information on how to recycle this battery.

2
FZ10-PP.book 3 ページ ２００３年１１月１８日 火曜日 午後１時７分

Safety

FCC Note: (U.S. only) Trade Name: Panasonic

This equipment has been tested and Model No.: DMC-FZ10
found to comply with the limits for a Responsible party: Matsushita Electric
Class B digital device, pursuant to Corporation of
Part 15 of the FCC Rules. These America
limits are designed to provide One Panasonic
reasonable protection against Way, Secaucus, NJ
harmful interference in a residential 07094
installation. This equipment Support Contact: Panasonic
generates, uses, and can radiate Consumer
radio frequency energy and, if not Electronics
installed and used in accordance Company
with the instructions, may cause 1-800-272-7033
harmful interference to radio
This device complies with Part 15 of
communications. However, there is
no guarantee that interference will the FCC Rules. Operation is subject
not occur in a particular installation. to the following two conditions: (1)
If this equipment does cause harmful This device may not cause harmful
interference to radio or television interference, and (2) this device must
reception, which can be determined accept any interference received,
by turning the equipment off and on, including interference that may
the user is encouraged to try to cause undesired operation.
correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving This Class B digital apparatus
antenna. complies with Canadian ICES-003
• Increase the separation between
the equipment and receiver.
• Connect the equipment into an
outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an
experienced radio/TV technician
for help.
FCC Caution: To assure continued
compliance, follow the
attached installation Extremely high precision technology
instructions and use is employed to produce the LCD
only shielded interface monitor/Viewfinder screen. The
cables with ferrite core result is more than 99.99% effective
when connecting to pixels with a mere 0.01% of the
computer or peripheral pixels inactive or always lit. However,
devices. this is not a malfunction and does
Any changes or modifications not not affect the recorded pictures.
expressly approved by the party
responsible for compliance could
void the user’s authority to operate
this equipment.

3
FZ10-PP.book 4 ページ ２００３年１１月１８日 火曜日 午後１時７分

Contents Recording pictures

(advanced)
Safety About the EXPOSURE Button........... 51
Information for Your Safety ................. 2 Taking Pictures with Aperture-priority
AE .................................................. 52
Preparation Taking Pictures with Shutter-priority
Standard Accessories ......................... 6 AE .................................................. 53
Taking Pictures with Manual
Names of the Components ................. 8
Quick Guide ...................................... 10 Exposure........................................ 54
Charging the Battery ......................... 12 Aperture Value and Shutter Speed ... 56
Taking Pictures using Macro
About the Battery .............................. 13
Inserting the Battery .......................... 14 Mode.............................................. 57
Removing the Battery........................ 15 Taking Pictures using Portrait
Mode.............................................. 58
Using the AC Adaptor ....................... 16
About the Card .................................. 17 Taking Pictures using Sports
Inserting the Card.............................. 18 Mode.............................................. 59
Taking Pictures using Panning
Removing the Card ........................... 19
Attaching the Strap............................ 20 Mode.............................................. 60
Attaching the Lens Hood/ Taking Pictures using Night Portrait
Mode.............................................. 62
Lens Cap ....................................... 21
Setting the Date/Time (Clock Set)..... 22 Recording Motion Images ................. 63
Setup Menu....................................... 24 Taking Pictures with Manual
Focus ............................................. 65
Using the LCD Monitor/Viewfinder .... 27
About the Histogram ......................... 29 Setting the White Balance ................. 67
The Mode Dial................................... 30 Setting the White Balance manually
(White set) ..................................... 69
Finely Adjusting the White
Recording pictures (basic) Balance.......................................... 70
Taking Pictures ................................. 31
Changing the Picture Size................. 71
Checking the Recorded Picture
Changing the Quality......................... 72
(Review) ........................................ 36
Taking Pictures using Spot Mode...... 73
Using the Optical Zoom..................... 37
Setting ISO Sensitivity....................... 74
Taking Pictures using the Built-in
Taking Pictures with Audio ................ 75
Flash.............................................. 38
Using the Continuous AF .................. 76
Compensating the Exposure............. 41
Using the Digital Zoom ...................... 77
Taking Pictures using Auto
Using the Color Effect ....................... 78
Bracket .......................................... 42
Adjusting the Quality of the Picture
Taking Pictures with the Self-timer.... 43
(Picture Adjustment) ...................... 79
Taking Pictures using Burst Mode .... 44
Using the Optical Image Stabilizer .... 80
Creating Flip Animation ..................... 81
Playback (basic) Using the External Flash ................... 84
Playing Back Pictures ....................... 45 Using the Conversion Lens ............... 86
9 Pictures Multi Playback .................. 46
Using the Playback Zoom ................. 47
Deleting Pictures ............................... 48

4
FZ10-PP.book 5 ページ ２００３年１１月１８日 火曜日 午後１時７分

Playback (advanced) Others

Playing Back Pictures with Audio...... 88 Using the MC Protector/ND Filter.... 117
Playing Back Motion Images............. 89 After Use ......................................... 118
Rotating the Picture........................... 90 Screen Display ................................ 119
Setting the Picture to be Printed and The Menu Items .............................. 121
the Number of Prints Cautions for Use.............................. 123
(DPOF Print Setting)...................... 91 Approximate number of recordable
Preventing Accidental Erasure of pictures and the size.................... 126
the Picture ..................................... 96 Message Display ............................. 127
Playing Back with Slide Show ........... 98 Troubleshooting............................... 128
Adding Audio to Recorded Pictures Specifications .................................. 130
(Audio Dubbing)........................... 100 Digital Camera Accessory
Resizing the Pictures ...................... 101 System......................................... 132
Trimming the Pictures ..................... 103 Digital Camera Accessory Order
Formatting the Card ........................ 105 Form (For USA Customers)......... 133
Playing Back Pictures with a TV Request for Service Notice
Screen ......................................... 106 (For USA Only) ............................ 134
Before Connecting with USB Limited Warranty (For USA Only).... 135
Connection Cable ........................ 107 Customer Services Directory
Connecting to a PC (For USA Only) ............................ 137
(Mass Storage) ............................ 109 Index................................................ 138
Connecting to a PC (PTP)............... 110 Spanish Quick Use Guide/
Connecting to a Printer ................... 112 Guía española de uso rápido....... 140
Using a Printer (PictBridge)............. 113
Using a Printer
(USB Direct-Print)........................ 115

5
FZ10-PP.book 6 ページ ２００３年１１月１８日 火曜日 午後１時７分

Preparation
Preparation

Standard Accessories
Before using your camera, check the contents.

∫ SD Memory Card (16 MB) ∫ AC Cable

RP-SD016B K2CA2EA00002
(In the text, it is indicated as “Card”)

∫ DC Cable
K2GH2DB00003
∫ Battery Pack
CGA-S002A
(In the text, it is indicated as “Battery”)

∫ A/V Cable
K1V204C10001

∫ Battery Charger/AC Adaptor

DE-928A
(In the text, it is indicated as
“AC Adaptor”)

6
FZ10-PP.book 7 ページ ２００３年１１月１８日 火曜日 午後１時７分

Preparation
∫ USB Connection Cable
K1HA05CD0004

∫ CD-ROM

∫ Lens Cap
VYK0W96

∫ Strap
VFC4036

∫ Lens Hood
(72 mm threading for MC protector
and ND filter)
VYQ2793 (Silver)
VYQ2824 (Black)

7
FZ10-PP.book 8 ページ ２００３年１１月１８日 火曜日 午後１時７分

Preparation
Preparation

Names of the Components

1 Lens
1 2 3 4 2 Flash
3 Microphone (P63, 75)
4 Self-timer Indicator (P43)

5 Viewfinder (P27)
6 Diopter Adjustment Dial (P28)
7 Flash Open Button (P38)
8 [EVF/LCD] Button (P27)
9 [DISPLAY] Button (P27)
10 [EXPOSURE] Button
(P35, 51, 52, 53, 54)
5 6 7 8 9 10 11 12 11 Power Indicator (P32)
12 Camera Switch (P11)
13 LCD Monitor (P27, 119)
14 [MENU] Button (P24)
15 Delete Button (P48)
16 Cursor buttons
2/Self-timer Button (P43)
4/REVIEW/SET Button (P36)
1/Flash Mode Button (P38)
3/Exposure Compensation (P41)/
Auto Bracket (P42)/White Balance
Fine Adjustment (P70)/Flash Output
13 14 15 16 17 Adjustment (P40) Button
17 Speaker (P88)

18 18 Lens Barrel (P33)

19 19 Lens Ring (P21)
20 MF Ring (P65)
20 21 Zoom Lever (P37, 77)
22 Hot Shoe (P84)
23 Mode Dial (P30)
21 24 Shutter Button (P31)
25 Single/Burst Mode Button (P44)

22 23 24 25
8
FZ10-PP.book 9 ページ ２００３年１１月１８日 火曜日 午後１時７分

Preparation
26 Focus Switch (P65)
27 [A/V OUT] Socket (P106)
26 28 [USB] Socket (5pin)
(P109, 110, 112)
29 Terminal Door

27
28
29
30 Strap Eyelet (P20)
31 [DC IN] Socket (P16)
32 [DC IN] Terminal Door (P16)
30
31
32

33 Card/Battery Door (P14, 18)

34 Card/Battery Door Open Lever
(P14, 18)
35 Tripod Receptacle

33 34 35
ª Battery Charger/AC Adaptor
(P12, 16)
1 1 [AC INT] Terminal
2 2 [POWER] Indicator
3 3 [CHARGE] Indicator
4 4 Battery Attachment Part
5 [DC OUT] Terminal

9
FZ10-PP.book 10 ページ ２００３年１１月１８日 火曜日 午後１時７分

Preparation

Quick Guide
• Charge the battery before using.
• Prepare the Camera/AC cable/Battery/AC adaptor/Card.
• Check that the camera is turned off and that the lens is retracted.
• Close the flash. (P38)

ª Preparation

1 Charge the battery. (P12) 3 1 Insert the card. (P18)

2 Close the card/battery door.

• The battery cannot be charged

when the DC cable is connected to
the AC adaptor.
2 1 Slide the lever to open the
card/battery door.
2 Insert the battery. (P14)

MEMORY CARD/
BATTERY

OPEN

10
FZ10-PP.book 11 ページ ２００３年１１月１８日 火曜日 午後１時７分

Preparation
ª Recording ª Playback
• Remove the lens cap.
• Be careful not to lose the lens cap.
6 1 Select Playback mode [ ].
2 Select the picture you want to
view. (P45)
4 1 Turn the camera on.
2 Set the clock. (P22)

A/S/M
3 Select Program AE mode [ ]. P

A/S
/M
P

WB

OFF ON

RE
VIE W
SET

5 1 Open the flash.

(When using the flash) (P38)
2 Take a picture. (P31)

OPEN

11
FZ10-PP.book 12 ページ ２００３年１１月１８日 火曜日 午後１時７分

Preparation

Charging the Battery

Charge the battery before using.

1 Connect the AC cable. 3 Detach the battery.

• The [POWER] Indicator A lights.

• The battery cannot be charged
¬Suggestions/Tips ¬
when the DC cable is connected to
the AC adaptor. • After use, be sure to disconnect the
AC cable.
2 Attach the battery to the AC
• The battery becomes warm after use/
adaptor.
charge or during charge. The camera
also becomes warm during use.
However, it is not a malfunction.
• The battery and AC adaptor are
designed only for this camera. Do
not use them with any other
equipment.
• Do not disassemble or alter the AC
adaptor.

• When the [CHARGE] Indicator B

lights, charging starts.
• When the [CHARGE] Indicator B
turns off (in about 90 minutes),
charging is finished.

12
FZ10-PP.book 13 ページ ２００３年１１月１８日 火曜日 午後１時７分

Preparation

About the Battery

ª Battery indication
The remaining battery power appears on the screen.
(This does not appear when using AC adaptor)
> > >
(Blinks in red): Recharge or replace the battery.

ª Charging time and available recording time

Measured under the following conditions:
• Temperature: 77°F (25°C)/Humidity: 60%
• Recording once every 30 seconds, flash every other record.
• Using the battery (supplied) and 16 MB SD Memory Card (supplied) [Picture
size: 2304k1728/Quality: Fine (When deleting all pictures after full use)]

Continuous recording/playback time

Charging time
(recordable number)
Recording with LCD monitor
Approx. 100 min.
(equal to 200 still pictures)
Recording with Viewfinder
Supplied battery Approx. 90 min. Approx. 120 min.
(equal to 240 still pictures)
Playback with LCD monitor
Approx. 180 min.
The recording time (recordable number) and playback time depend on the condition.

ª Charging environment and charging error

• Charge the battery under temperature of 50°F – 95°F (10°C – 35°C).
(The battery should also be the same temperature.)
• When charging starts, the [CHARGE] Indicator lights.
If the charging error occurs, the [CHARGE] Indicator blinks at about 1 second
cycles.
In this case, disconnect the AC adaptor from the electrical outlet, remove the
battery and ensure both room and battery temperature are not too low or high and
then charge it again.
If the problem persists, consult the dealer or your nearest servicenter.

13
FZ10-PP.book 14 ページ ２００３年１１月１８日 火曜日 午後１時７分

Preparation

Inserting the Battery

Preparation
• Check that the camera is turned off and that the lens is retracted.
• Close the flash.

1 Slide the lever to open the card/ 3 Close the card/battery door.
battery door.

MEMORY CARD/
BATTERY

OPEN

2 Insert the charged battery until it

clicks.

14
FZ10-PP.book 15 ページ ２００３年１１月１８日 火曜日 午後１時７分

Preparation

Removing the Battery

Preparation
• Check that the camera is turned off and that the lens is retracted.
• Close the flash.

1 Slide the lever to open the card/ 3 Close the card/battery door.
battery door.

MEMORY CARD/
BATTERY

OPEN

2 Slide the lock 1 to remove the

battery. ¬Suggestions/Tips ¬
• If you will not use the camera for a
long time, remove the battery.
• After the fully charged battery has
been inserted for more than 24 hours,
the clock setting is stored (in the
camera) for max. 3 months after the
battery was removed, in accordance
with the elapsed time after the battery
is inserted. (The time may be shorter if
the battery is not charged sufficiently.)
If more than 3 months has passed, the
clock setting will be lost. In this case,
set the clock again. (P22)
• Do not open the card/battery door
during the access to the card.
• The supplied battery is designed
only for this camera. Do not use it
with any other equipment.

15
FZ10-PP.book 16 ページ ２００３年１１月１８日 火曜日 午後１時７分

Preparation

Using the AC Adaptor

You can use the camera without worrying about battery discharge by connecting to
an AC adaptor.
Preparation
• Check that the camera is turned off and that the lens is retracted.
• Close the flash.

1 Connect the AC cable. 3 Connect the DC cable.

2 Open the [DC IN] terminal door.

¬Suggestions/Tips ¬
• Use the supplied DC cable.
If you use other DC cables, it may
cause a malfunction.
• The camera becomes warm during
use. This is not a malfunction.
• Disconnect the AC adaptor and DC
cable when the camera is not in use.
• The battery cannot be charged in the
camera even if the AC adaptor is
connected.

16
FZ10-PP.book 17 ページ ２００３年１１月１８日 火曜日 午後１時７分

Preparation

About the Card

ª Access to the card ª SD Memory Card (supplied) and
MultiMediaCard (optional)
While the card is accessed, the card
access indication 1 lights. The SD Memory Card and
MultiMediaCard are small, lightweight,
P 2304 removable external memory cards. The
1 19 reading/ writing speed of an SD Memory
Card is fast. The SD Memory Card is
equipped with a Write-Protect switch
that can inhibit writing and formatting a
card. (When the switch is slid to the
[LOCK] side, it is not possible to write or
delete data on the card and format it.
When the card access indication 1 When the switch is unlocked, these
lights, do not: functions become available.)
• turn the camera off.
• remove the battery or the card. SD Memory Card
• disconnect the DC cable if you use the
AC adaptor.
The card and the card contents may be
damaged and the camera may not
operate normally.

It is possible that data stored on the MultiMediaCard

card can be damaged due to accidental
erasure, static electricity, electrical noise
or a defective card. We recommend
storing precious data to your PC’s hard
drive. (P109, 110)
¬Suggestions/Tips ¬
• The reading/writing speed of a
MultiMediaCard is slower than an SD
Memory Card. When a
MultiMediaCard is used, the
performance of certain features may
be slightly slower than advertised.
• After recording motion images using
the MultiMediaCard, the card access
indication may appear for a while, but
this is not a malfunction.
• Keep the Memory Card out of reach of
children to prevent swallowing.

17
FZ10-PP.book 18 ページ ２００３年１１月１８日 火曜日 午後１時７分

Preparation

Inserting the Card

Preparation
• Check that the camera is turned off and that the lens is retracted.
• Close the flash.

1 Slide the lever to open the card/ 3 Close the card/battery door.
battery door.

MEMORY CARD/
BATTERY

OPEN

2 Insert the card with the label

facing the front of the camera until
it clicks.

• Insert the card, pressing gently

until it locks in place. If the card will
not insert freely, it may be reversed.
Do not force the card.
• Do not touch the connection
terminals on the back side of the
card.

18
FZ10-PP.book 19 ページ ２００３年１１月１８日 火曜日 午後１時７分

Preparation

Removing the Card

Preparation
• Check that the camera is turned off and that the lens is retracted.
• Close the flash.

¬Suggestions/Tips ¬
1 Slide the lever to open the card/
battery door. • The card may be damaged if it is
removed while the camera is on.
• If the card/battery door cannot be
completely closed, remove the card
and insert it again.
• If the card cannot be fully inserted,
check the direction of the card.
MEMORY CARD/
BATTERY
• We recommend using Panasonic’s SD
OPEN
Memory Card. (Use only the genuine
card.)
• The card may be damaged if it is not
fully inserted.
2 Push the card until it clicks, then
pull the card out upright.

3 Close the card/battery door.

19
FZ10-PP.book 20 ページ ２００３年１１月１８日 火曜日 午後１時７分

Preparation

Attaching the Strap

1 1 Pressing both sides of the 3 Pass the metal fitting through the
cover, eyelet of the camera.
2 Pull out the black strap holder
completely.

4 Rotate the black strap holder in

the opposite direction until it
clicks.

5 Slide the cover until it is attached

2 Detach the black strap holder from firmly.
the metal fitting.

• Attach the strap to the other side of the

• When the black strap holder is camera being careful not to twist it.
completely detached, attach it • Attach the strap so that you can see
again as above. “Panasonic” logo.
• Check that the strap is firmly attached
to the camera.

20
FZ10-PP.book 21 ページ ２００３年１１月１８日 火曜日 午後１時７分

Preparation

Attaching the Lens Hood/Lens Cap

Preparation
• Check that the camera is turned off and that the lens is retracted.
• Close the flash.

ª Lens Hood ª Lens Cap

1 1 Detach the lens ring. 1 Attach the lens cap.

2 Attach the lens hood.

• Be careful not to lose the lens cap.

ª When attaching the lens cap

• When you turn the camera off, carry
• In bright sunlight or when there is
the camera or play back the pictures,
backlight, the lens hood will
attach the lens cap to protect the
minimize lens flare and ghosting.
surface of the lens.
• The lens hood cuts off excess
• Detach the lens cap before turning on
lighting and improves the picture
the camera in the recording mode.
quality.
• When detaching the lens hood,
• Consult the dealer or your nearest
refer to P118.
servicenter if you lose the supplied
accessories. (You can purchase the
ª When attaching the lens hood
accessories separately.)
• When taking pictures with flash, photo
flash is interrupted by the lens hood
and the bottom of the screen becomes
dark. (vignetting effect)
• When taking pictures with flash, we
recommend detaching the lens hood.

21
FZ10-PP.book 22 ページ ２００３年１１月１８日 火曜日 午後１時７分

Preparation

Setting the Date/Time (Clock Set)

ª Initial setting
1 Select [CLOCK SET] from the
The clock is not set when the camera is [SETUP] menu. (P24)
shipped. When you turn the camera on,
the clock setting screen appears. REC SETUP 2/3
MF ASSIST ON
NO.RESET
RESET
PLEASE SET THE CLOCK CLOCK SET
CLOCK SET MENU
SELECT SET EXIT MENU

WB
MENU

When pressing the [MENU] button, the

RE
screen shown in step 2 appears. Set the VIE W
SET
clock on it.
WB WB

RE RE
VIE W VIE W
SET SET

2 Set date and time.

CLOCK SET

10 : 00 DEC . 11 . 2003

M/D/Y

SELECT SET EXIT MENU

WB WB

RE RE
VIE W VIE W
SET SET

• 2/1: Select the desired item.

• 3/4: Set date and time.

22
FZ10-PP.book 23 ページ ２００３年１１月１８日 火曜日 午後１時７分

Preparation

¬Suggestions/Tips ¬
3 Select [M/D/Y], [D/M/Y] or [Y/M/D].
• You can set the year from 2003 to
CLOCK SET 2099. The 24-hour system is used.
• After the fully charged battery has
10:001DEC.11.2003 been inserted for more than 24 hours,
the clock setting is stored (in the
M/D/Y camera) for max. 3 months after the
battery was removed, in accordance
SELECT SET EXIT MENU with the elapsed time after the battery
is inserted. (The time may be shorter if
WB the battery is not charged sufficiently.)
If more than 3 months has passed, the
clock setting will be lost. In this case,
RE
VIE W set the clock again.
SET

• Close the menu by pressing the

[MENU] button 2 times after
finishing the setting.
• Check if the clock setting is correct,
after turning the camera off and on.

ª Date Printing
• You can set the date printing in DPOF
print setting on this camera. (P95)
• Using the supplied software, [SD
Viewer for DSC], it is possible to have
the date imprinted on the picture. For
details, please read the supplied
operating instructions for PC
connection.
• When you ask photo studios for
printing, be sure to order the printing
of the date. For further information,
ask a photo studio. Depending on the
studio, it may not be printed.

23
FZ10-PP.book 24 ページ ２００３年１１月１８日 火曜日 午後１時７分

Preparation

Setup Menu
1 Turn the camera on. 4 Select the desired item.

REC SETUP 1/3

OFF ON
MONITOR
WB
AUTO REVIEW
OFF 1SEC. 3SEC. ZOOM
RE

SET
VI E W
BEEP
POWER SAVE 2MIN.

SELECT SET EXIT MENU

5 Set the desired value.

REC SETUP 1/3

2 Press the [MENU] button. MONITOR

WB
AUTO REVIEW
REC 1/4 SETUP OFF 1SEC. 3SEC. ZOOM

W.BALANCE AUTO
RE

SET
VI E W
BEEP
MENU PICT.SIZE 2304 POWER SAVE 2MIN.

QUALITY SELECT SET EXIT MENU

SPOT MODE OFF
• Close the menu by pressing the
SELECT SET EXIT MENU [MENU] button after finishing the
setting.

3 Select the [SETUP] Menu.

REC SETUP 1/3

MONITOR
WB
AUTO REVIEW OFF
BEEP
RE
VI E W POWER SAVE 2MIN.
SET

SELECT SET EXIT MENU

24
FZ10-PP.book 25 ページ ２００３年１１月１８日 火曜日 午後１時７分

Preparation
You can control the following items on [SETUP] Menu.

Menu Functions
MONITOR/ Adjust the brightness of the LCD monitor (when pictures
FINDER appear on the LCD monitor) or Viewfinder (when pictures
appear on the Viewfinder) in 7 steps.
AUTO • [OFF]: The recorded picture does not automatically
REVIEW°1 appear.
• [1SEC.]: The recorded picture automatically appears
on the screen for about 1 second.
• [3SEC.]: The recorded picture automatically appears
on the screen for about 3 seconds.
• [ZOOM]: The recorded picture automatically appears
on the screen for about 1 second. Then it is
enlarged 4 times and appears for about
1 second. This mode is useful to confirm the
focus.
• In Motion image mode [ ], auto review function is not
activated.
• When using burst mode or auto bracket, the auto review
function works while recording the data into the card
regardless of the setting on the auto review function.
(The picture is not enlarged.)
• When using pictures with audio, the auto review
function works while recording the audio or the data into
the card regardless of the setting on the auto review
function. (The picture is not enlarged.)
BEEP •[ ]: The operational sound turns high.
•[ ]: The operational sound turns low.
•[ ]: The operational sound turns off.
POWER SAVE • [2MIN.]/[5MIN.]/[10MIN.]:
The camera is automatically turned off if it has
not been used for a predetermined amount of
time.
(Press the shutter button or turn the camera off
and on to cancel the power save mode.)
• [OFF]: The camera is not automatically turned off.
• When using the AC adaptor/connecting to a PC or
printer/recording motion images/playing back motion
images/during Slide Show, the power save mode is not
activated.

°1 Recording mode only

25
FZ10-PP.book 26 ページ ２００３年１１月１８日 火曜日 午後１時７分

Preparation

Menu Functions
MF ASSIST°1 In manual focus, assistance screen appears on the center
of the screen to facilitate focusing on the subject. (P65)
NO.RESET°1 Set this when you want to start the file number of the picture
from 0001 on the next recording. (The folder number is
updated, and the file number starts from 0001.)
• The folder number can be assigned from 100 to 999.
When the folder number reaches to 999, it cannot be
reset. We recommend formatting the card after saving the
data on a PC or other.
RESET°1 The camera is reset to the initial settings. However, the
folder number and the clock settings are not changed.
CLOCK SET Change the date and time. (P22)
USB MODE Set before connecting to a PC or a printer. (P107)
LANGUAGE Set to the language on the menu screen from the following
7 languages.
Set to the desired language with 2/1 and determine it with
4.
• [ENGLISH]: The menu screen in English
• [DEUTSCH]: The menu screen in German
• [FRANÇAIS]: The menu screen in French
• [ESPAÑOL]: The menu screen in Spanish
• [ITALIANO]: The menu screen in Italian
•[ ]: The menu screen in Chinese (Simplified)
•[ ]: The menu screen in Japanese
• When you set to other language by mistake, select [ ]
from the menu icons to set the desired language.
PLAY ON When Viewfinder is selected in the recording mode, the
LCD°2 picture automatically appears on the LCD monitor in review
or playback. (P28)
VOLUME°2 The volume of speakers can be adjusted in 7 steps.
• When you connect the camera to a TV, the volume of the
speakers of the TV is not changed.
VIDEO OUT°2 • [NTSC]: Video output is set to NTSC system.
• [PAL]: Video output is set to PAL system. (P106)

°1 Recording mode only °2 Playback mode only

26
FZ10-PP.book 27 ページ ２００３年１１月１８日 火曜日 午後１時７分

Preparation

Using the LCD Monitor/Viewfinder

ª Switching the screen to be turned In recording mode
on
Press the [EVF/LCD] button to switch to P 2304 P 2304
1 19 1 19
the screen you would like to turn on.

P 2304
1 19

P
1
2304
19 C Display
D Display with histogram
E Nondisplay (Recording guide line)
F Nondisplay
¢Histogram
A LCD monitor (LCD)
B Viewfinder (EVF) In playback mode
• When the LCD monitor turns on, the
Viewfinder turns off. (and vice versa) 2304
100 _ 0001
1/19
ª Selecting the screen to be used
Press the [DISPLAY] button to switch to
10:00 DEC. 1.2003
the screen to be used.
• When the menu screen appears, 2304
100 _ 0001
during multi playback or during 1/19

playback zoom, the [DISPLAY] button

is not activated. P F2.8 1/25 ISO100 AUTO

10:00 DEC. 1.2003

G Display
H Display with recording information
and histogram
I Nondisplay

27
FZ10-PP.book 28 ページ ２００３年１１月１８日 火曜日 午後１時７分

Preparation
ª Diopter adjustment ª Monitor priority
This feature is useful for users who wear When setting [PLAY ON LCD] to [ON]
corrective lenses and prefer to use the on the [SETUP] menu (P26), the LCD
Viewfinder. monitor is turned on in the following
cases.
Preparation
• Press the [EVF/LCD] button to display You can save the time to switch the
the Viewfinder. display to the LCD monitor even when
using the Viewfinder in recording.
1 Adjust the diopter, rotating the • When the recording mode is switched
diopter adjustment dial. to playback mode.
• When reviewing pictures (P36)
• When turning the camera on in
playback mode.

ª Recording guide line

You can achieve balanced pictures by
aligning the subject on the cross point of
the horizontal and vertical guidelines.
You can also take pictures easily by
adjusting the horizon to the guide line.

You can take pictures with

well-designed composition by watching
the size and the balance of subjects.

P 2304
1 19

28
FZ10-PP.book 29 ページ ２００３年１１月１８日 火曜日 午後１時７分

Preparation

About the Histogram

• A histogram is a graph that displays brightness along the horizontal axis (black to
white) and the number of pixels at each brightness level on the vertical axis.
• It allows the camera user to easily check the way a picture is being exposed.
• It is very useful if manual adjustments of the lens aperture and shutter speed are
available, especially in those situations where automatic exposure may be difficult
due to uneven lighting. Using the histogram feature will allow you to get the best
performance from the camera.

• When the values are concentrated to ¬Suggestions/Tips ¬

the left as A, the picture is under
• When the brightness of the picture
exposed.
and the histogram do not match
• When the values in the histogram are
each other, the histogram turns
distributed as B, the exposure is
yellow.
adequate and the brightness is • The histogram turns yellow in the
well-balanced. following cases.
• When the values are concentrated to
– When the flash is activated
the right as C, the picture is over – When the flash is closed
exposed.
1. Aperture-priority AE/
Shutter-priority AE:
ª Example of histogram When the brightness of the
screen is not correct or when the
2304
100 _ 0001 exposure is not adequately
1/19
adjusted
2. Manual exposure:
P F2.8 1/50 ISO100 AUTO

10:00 DEC. 1.2003 When the shutter speed is slower

than 1/13th
2304
100 _ 0001 3. In modes other than the above:
1/19
When the brightness of the
screen is not correct in dark
P F2.8 1/100 ISO100 AUTO

10:00 DEC. 1.2003 places

• The histogram does not appear when
2304
100 _ 0001 in Motion image mode [ ], during
1/19
multi playback and playback zoom.
• The histogram in recording and
P F2.8 1/200 ISO100

10:00 DEC. 1.2003

AUTO
playback may not match each other.
• The histogram in this camera does not
agree with the one displayed in image
editing software on PC, etc.
A Under Exposed
• The histogram in the recording mode
B Properly Exposed
is an approximation.
C Over Exposed
¢Histogram

29
FZ10-PP.book 30 ページ ２００３年１１月１８日 火曜日 午後１時７分

Preparation

The Mode Dial

Select the desired mode turning the mode dial.

A/S
/M

: Program AE mode (P31) : Sports mode (P59)

The aperture value and the shutter This allows you to record still action
speed are automatically adjusted. pictures of outdoor sports easily.

: A/S/M mode (P52–54) : Panning mode (P60)

: Aperture-priority AE (P52) This allows you to record a subject in
motion sharply while blurring the
The shutter speed is adjusted
automatically according to the background.
aperture value you set.
: Night portrait mode (P62)
: Shutter-priority AE (P53) This allows you to record the subject
The aperture value is adjusted clearly in front of beautiful night
automatically according to the shutter illumination scenery.
speed you set.
: Manual exposure (P54) : Motion image mode (P63)
The aperture value and the shutter This allows you to record motion
speed are manually adjusted. images.

: Macro mode (P57) : Playback mode (P45)

This allows you to get closer to the This allows you to play back recorded
subject up to 0.16 feet (5 cm) (Wide). pictures.

: Portrait mode (P58)

This allows you to easily achieve the
depth of focus effect. The subject
stands out in front of an unfocused
background.

30
FZ10-PP.book 31 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (basic)

Recording pictures (basic)

Taking Pictures
Preparation
• Insert the charged battery (P14) or connect the AC adaptor (P16).
• Insert the card. (P18)
• Remove the lens cap.

1 1 Turn the camera on. 3 Focus on the subject to take the

2 Select Program AE mode [ ]. picture.
3 Slide the focus switch to [AF].

A/S
/M P 2304
P 1 19

F2.8 1/25

OFF ON
FOCUS

AF
MF

• A: Press the shutter button

2 Aim the AF area 1 to the point halfway to focus.
you want to focus. • B: Press the shutter button fully to
take the picture.
• The focus indication 2 lights and
P 2304
then the aperture value 3 and the
1 19 shutter speed 4 appear.
• When the focus indication is
blinking, the subject is not focused.
Press the shutter button halfway
and focus on the subject again.

31
FZ10-PP.book 32 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (basic)

ª Posture to take good pictures • Hold the camera firmly with your right
To take pictures without blurring: hand.
• Put your left hand on the lens ring to
• Hold the camera gently with both
hands, keep arms stationary at your keep the camera stationary.
side and stand with your feet slightly • Do not cover the microphone with your
finger or other objects.
apart.
• Check that the camera is not shaken • Do not touch the lens barrel.
when pressing the shutter button
ª Power indicator
halfway.
• After pressing the shutter button, keep
the camera stationary until the picture OFF ON
appears on the screen.
• In the following cases, keep the
camera stationary for a long time.
Lighting:
– Slow sync./Red-eye reduction
• When turning the camera on
[ ] (P38)
– In Night portrait mode [ ] (P62) Blinking:
– When you set the shutter speed • When the card/battery door is open
slower (P35, 53, 54) • When the card is not inserted
• When there is no remaining capacity
When recording with LCD Monitor
on the card
• When the card is locked in the
recording mode
• When the remaining battery power is
low (blinking slowly)

ª Focusing
• The focus range is 0.98 feet
(30 cm) – ¶ (Wide), 6.56 feet (2 m) – ¶
When recording with Viewfinder (Tele).
• If you press the shutter button fully
without prefocusing, pictures may be
blurry or unfocused.
• When the subject is focused, the
camera beeps 2 times. If not, it beeps
4 times.
• If the camera will not focus after a few
tries, turn it off and on and try again.
• Refer to P25 if you want to turn the
Position of feet operational sound off.

32
FZ10-PP.book 33 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (basic)

• In the following cases, the camera ª Jitter (camera shake)
cannot focus on subjects properly in
• When jitter could occur, the jitter alert
Program AE mode.
1 appears.
– When including both near and
distant subjects in a scene
– When there is dirt on the glass
P 2304
between the lens and the subject
1 19
– When there are illuminated or
glittering objects around the subject
– When taking a picture in a dark place
– When the subject moves fast
– When the scene is poor in contrast
– When jitter occurs F2.8 1/8
– When recording a very bright subject
• When the jitter alert appears, we
We recommend taking pictures using recommend using a tripod. If you
manual focus (P65), prefocus (P66) or cannot use a tripod, be careful of how
AF/AE lock. you hold the camera. (P32)
• Even if the focus indication appears • Be careful of jittering when pressing
and the subject is focused, it is the shutter button.
canceled when you release the shutter
button. Press the shutter button ª Care for the camera
halfway again.
• Check to make sure there is no stain
ª Exposure or dirt on the lens.
• Do not touch the lens directly.
• If the exposure is not adequate, the • Do not cause impact to the lens or
indication of the aperture value and lens barrel.
the shutter speed on the screen turns • When turning the camera on in the
red. (However, the aperture value and recording mode, the lens barrel comes
the shutter speed do not turn red when out. Check to make sure there are no
the flash is activated.) obstacles in front of the lens.
• The brightness of the screen may • Take care not to touch or stain the
differ from that of recorded pictures. In surface of the lens. When the lens
particular, when taking pictures in dark becomes dirty or dust attaches to the
places with slow shutter, the subject lens, check if the lens is retracted, use
looks dark on the screen, but the a commercial blower brush to remove
actual picture is bright. dust or dirt and wipe the lens with a
• When most of the subjects in the dry, soft cloth. If you use solvents such
screen are bright (e.g. blue sky on a as benzine, alcohol or thinner, the
clear day, snowy field, etc.), the camera may be discolored or broken.
recorded pictures may become dark. • When using the camera in a sandy or
In this case, compensate the dusty place, be careful not to let dirt,
exposure. (P41) grit or seawater come into the camera.

33
FZ10-PP.book 34 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (basic)

¬Suggestions/Tips ¬ ª AF/AE Lock (AF: Auto focus/
• When brightness has changed due AE: Auto exposure)
to the zoom or the movement of the P 2304

camera, the lens may click and the 1 19

picture on the screen may be
drastically changed. However, the
pictures are not affected.
The sound is caused by automatic
adjustment of the aperture. It is not
a malfunction. When recording a picture of people with
• When pressing the shutter button a composition as the above picture, you
halfway, the screen may become cannot focus on the subject because it
dark or bright for a moment; this is is out of AF area in usual operation.
not a malfunction. This is caused In this case,
by adjusting the aperture value. 1. Aim the AF area to the subject.
• If the camera is shaken while the 2. Press the shutter button halfway to fix
camera is turned off, you may hear the focus and the exposure.
some internal mechanical • When the subject is focused, the
movement. This is not a focus indication lights.
malfunction. 3. Keeping the focus and the exposure
• We recommend setting the clock fixed, move the camera as you want
again before taking pictures. (P22) to compose the picture.
• When the time for power save is set 4. Press the shutter button fully.
(P25), the camera is automatically
turned off if you do not operate within • You can repeatedly retry AF/AE lock
the set time. When operating the before pressing the shutter button.
camera again, press the shutter button
or turn the camera off and on. P 2304
1 19

F2.8 1/25

P 2304
1 19

F2.8 1/25

34
FZ10-PP.book 35 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (basic)

ª Program shift
2 3 4 5 6 7 8 9 10 11 12 13 14
In Program AE mode, you can change
2
the preset aperture value and the
2.8
shutter speed under the same 4
exposure. This is called Program shift. (A)
5.6

By this function, you can make the 8

background more blurred (by 11

decreasing the aperture value) or record 0 1/2 1/4 1/8 1/15 1/30 1/60 1/125 1/250 1/500 1/1000 1/2000

the subject in motion clearer (by setting (B)

to slow shutter speed) in Program AE (A): Aperture value

mode. (B): Shutter speed
• Press the shutter button halfway and
then press the [EXPOSURE] button ¬Suggestions/Tips ¬
while the aperture value and the • Program shift can be set in Macro
shutter speed appear (for mode (P57) too.
10 seconds). Then press 2/1 to • If the exposure is not adequate when
activate the Program shift. pressing the shutter button halfway,
the shutter speed turns red.
P 2304
1 19 • When Program shift can be set, you
cannot switch the flash mode or set
the self-timer. Press the [EXPOSURE]
button to cancel. (P51)
PROGRAM SHIFT • When 10 or more seconds have
F2.8 1/60
passed after the Program shift
EXPOSURE becomes effective, the status to
activate the Program shift is canceled
and returned to the Program AE
P 2304
mode. However, the setting on the
1 19 Program shift is memorized.
• Program shift is canceled when
turning the camera off.
• The Program shift may not be
PROGRAM SHIFT
activated depending on the brightness
F4.0 1/30
of the subject.
WB

RE
VIE W
SET

• When the Program shift is activated,

the Program shift indication 1
appears on the screen.

35
FZ10-PP.book 36 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (basic)

Checking the Recorded Picture (Review)

Preparation
• In Motion image mode [ ], review function is not activated.

1 Press 4. 2 Enlarge and shift the picture.

REVIEW1X REVIEW4X

EXIT 4X DELETE 1X 8X DELETE

WB WB
W T

RE RE
VIE W VIE W
SET SET

• The last recorded picture appear • : 1k>4k>8k

for about 10 seconds. • : 8k>4k>1k
• Press the shutter button halfway or
4 to cancel the review. ª Deleting the recorded picture
• You can check the previous or during the review
following picture with 2/1.
• When the recorded pictures are too DELETE SINGLE
bright or dim, compensate the
exposure. (P41) DELETE THIS PICTURE?

YES NO

SELECT
SET MULTI/ALL

WB WB

RE RE
VIE W VIE W
SET SET

• Once deleted, pictures cannot be

recovered.
• Multi pictures or all pictures can be
deleted. Read P49 or P50 to operate
them.

36
FZ10-PP.book 37 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (basic)

Using the Optical Zoom

You can make people and subjects appear closer with the 12 times optical zoom,
and landscapes can be recorded in wide angle.
Preparation
• Set the mode dial except for [ ]. (P30)

ª To make subjects appear closer

1k (Tele)

P 2304
1 19
W T 12X

6k

W T
12k

¬Suggestions/Tips ¬
• The picture may be slightly distorted
ª To make subjects appear further according to the lens. The distortion
away (Wide) will increase as you make subjects
wider and closer.
P 2304 • When using the zoom lens at high
1 19 magnification, the quality of the picture
W T 1X can be enhanced if a tripod is used. At
high magnification, even small
movements can cause a slight
decrease in picture sharpness.
• The indicated zoom magnification is
an approximation.

W T

37
FZ10-PP.book 38 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (basic)

Taking Pictures using the Built-in Flash

Preparation
• Set the mode dial except for [ ]/[ ]. (P30)

ª To open the flash : AUTO

The flash is automatically activated
Press the [ OPEN] button.
according to the recording condition.
: AUTO/Red-eye reduction
The flash is automatically activated
according to the recording condition.
It reduces the red-eye phenomenon
OPEN (eyes of the subject appear red in
photo flash) by lighting the flash
before the actual recording of the
picture.
ª To close the flash Use this when you take pictures of
people in low lighting conditions.
Press the flash until it clicks.
: Forced ON
The flash is activated every time a
picture is recorded forcibly.
Use this when your subject is back-lit
or under fluorescent light.
: Slow sync./Red-eye reduction
When you take a picture with a dark
background landscape, it makes the
shutter speed slow when the flash is
activated, so that the dark
• Be sure to close the flash when not in background landscape will become
use. bright. Simultaneously it reduces the
red-eye phenomenon.
ª Switching the flash setting Use this when taking pictures of
people with the dark background.
: Forced OFF
When you do not open the flash, this
mode is set. Even in dark places, the
WB
flash is not activated.
Use this when taking pictures in
places where use of the flash is not
RE
VIE W allowed.
SET

38
FZ10-PP.book 39 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (basic)

ª Available flash settings

P A S M

ª The available flash range to take pictures

ISO sensitivity Available flash range

ISO AUTO 1.31 feet (40 cm) – 13.1 feet (4 m)
ISO100 1.31 feet (40 cm) – 6.56 feet (2 m)
ISO200 1.97 feet (60 cm) – 9.18 feet (2.8 m)
ISO400 2.62 feet (80 cm) – 13.1 feet (4 m)
• The available flash range is an approximation.
• Refer to P32 for the focus range.

ª Shutter speed for each flash mode

Flash mode Shutter speed

: AUTO 1/60 – 1/2000
: AUTO/Red-eye reduction 1/60 – 1/2000
: Forced ON 1/60 – 1/2000
: Slow sync./
1 – 1/2000
Red-eye reduction
1/4 – 1/2000
: Forced OFF 8 – 1/2000
(in Night portrait mode [ ])
• Refer to P56 for the A/S/M modes.

39
FZ10-PP.book 40 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (basic)

ª Adjusting flash output • Do not cover the photo flash with
Adjust the flash output when the subject your fingers or any other items.
• If the subject is too close when using
is small or reflection ratio is extremely
high or low. the flash, the picture may be over
exposed.
1 Press 3 until [ FLASH] • When the jitter alert appears, we
appears on the screen to set the recommend using the flash.
flash output. • When you set to burst mode or auto
bracket, only 1 picture is recorded for
FLASH every flash activated.
• The flash icon turns red when
activating the flash and pressing the
shutter button halfway.
• When the flash is being charged, the
flash icon blinks red, and you cannot
SELECT EXIT take a picture even when you press
the shutter button fully.
WB WB WB
• When taking a picture with the
flash, we recommend removing the
lens hood. In some cases it may not
RE
VIE W
RE
VIE W
RE
VIE W allow the scene to be illuminated
SET SET SET properly.
• You can adjust this from j2 EV to • When taking a picture with the flash,
i2 EV in steps of 1/3 EV. the white balance will be automatically
• The determined flash output is adjusted [except for [ ] (Daylight)
memorized even if the camera is and [ WB ] (Flash)], but the white
turned off. balance may not be properly adjusted
when the photo flash is insufficient.
¬Suggestions/Tips ¬ • When the shutter speed is fast, the
• In Night portrait mode [ ], flash flash effect may not be sufficient.
setting is fixed to Slow sync./Red-eye • To avoid noises, we recommend
reduction [ ]. setting each item on [PICT.ADJ.] to
• In Motion image mode [ ] or when [LOW]. (P79)
the flash is closed, flash setting is fixed • Refer to P74 for the ISO sensitivity.
to the Forced OFF [ ]. • Refer to P84 for the external flash.
• When using the flash in ISO AUTO
setting, the ISO sensitivity is
automatically adjusted from ISO50 to
ISO400. To avoid noises, decrease the
ISO sensitivity.
• Do not stare at the photo flash from
close proximity when using the
flash.
• If you bring the flash too close to
the subjects, they may be distorted
or discolored by its heat and
lighting.
40
FZ10-PP.book 41 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (basic)

Compensating the Exposure

Use this function when you cannot achieve appropriate exposure due to the
difference of brightness between the subject and the background.
Preparation
• Set the mode dial except for [ ]/[ ]. (P30)

¬Suggestions/Tips ¬
1 Press 3 until [ EXPOSURE]
appears on the screen to • EV is an abbreviation of Exposure
compensate the exposure. Value, and it is the amount of light
given to the CCD by the aperture
EXPOSURE value and the shutter speed.
• The compensation range of the
exposure will be limited depending on
the brightness of the subject.
• The exposure compensation value
appears on the lower left of the
SELECT EXIT screen.
• The exposure value is memorized
WB WB WB even if the camera is turned off.
• You cannot compensate the exposure
in manual exposure.
RE RE RE
VIE W VIE W VIE W
SET SET SET

• You can compensate from j2 EV

to i2 EV in steps of 1/3 EV.

41
FZ10-PP.book 42 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (basic)

Taking Pictures using Auto Bracket

In this mode, 3 pictures are automatically recorded by each press of the shutter
button according to the compensation range of the exposure.
You can select the desired exposure among the 3 types of pictures.
[Preparation]
• Set the mode dial except for [ ]/[ ]. (P30)

¬Suggestions/Tips ¬
1 Press 3 until
[ AUTO BRACKET] appears • When setting the auto bracket, the
on the screen to set the auto bracket icon appears on the lower
compensation range of the left of the screen.
exposure. • Once you take a picture, auto bracket
will be canceled automatically.
AUTO BRACKET • When taking pictures using auto
bracket after the exposure
compensation, the pictures are based
on the compensated exposure.
When the exposure is compensated,
the compensated exposure value
SELECT EXIT appears on the lower left of the
screen.
WB WB • When the flash is activated, you can
take only 1 picture. Auto bracket
setting cannot be canceled.
RE RE
VIE W VIE W • When setting auto bracket, you cannot
SET SET
take a picture with audio.
WB WB • When setting auto bracket and the
burst mode simultaneously, auto
bracket will be performed.
RE RE
VIE W VIE W • The exposure may not be
SET SET
compensated with auto bracket
• You can select the exposure from
depending on the brightness of the
j1 EV to i1 EV in steps of 1/3 EV.
subject.
• When you do not use auto bracket,
select [OFF].

42
FZ10-PP.book 43 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (basic)

Taking Pictures with the Self-timer

Preparation
• Set the mode dial except for [ ]/[ ]. (P30)

1 Switch the self-timer setting. 2 Focus on the subject to take the

picture.
P 2304
1 19 P 2304
1 19

CANCEL MENU
WB

RE
VIE W
SET

• If you press the [MENU] button

: Self-timer set to 10 seconds
when the self-timer is set, the
;
self-timer setting is canceled.
: Self-timer set to 2 seconds
;
¬Suggestions/Tips ¬
No display (canceled)
• When using a tripod or other cases,
setting the self-timer to 2 seconds is
convenient to stabilize the jitter caused
by pressing the shutter button.
• The self-timer
indicator 1 blinks
and the shutter is
activated after
10 seconds (or
2 seconds).
• When pressing the button fully at a
stroke, the subject is automatically
focused just before recording pictures.
(When setting the manual focus, the
focus is fixed.)
• When setting the self-timer in the burst
mode, you can take only 1 picture.
• We recommend using a tripod when
setting the self-timer.

43
FZ10-PP.book 44 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (basic)

Taking Pictures using Burst Mode

Preparation
• Set the mode dial except for [ ]/[ ]. (P30)

¬Suggestions/Tips ¬
1 Switch the burst mode setting.
ª Number of pictures recorded in
P 2304 burst mode
1 19
H Number of recordable
Burst pictures
speed

4 frames/ max. max.

H second 5 frames 7 frames
2 frames/ max. max.
L second 5 frames 7 frames

• It is possible to record 4 frames in

1 second in burst mode at a shutter
speed higher than 1/60th.
• If the flash is activated, you can record
H : High speed only 1 frame.
; • You cannot take pictures with audio in
L : Low speed the burst mode.
; • When setting auto bracket and the
No display (canceled) burst mode simultaneously, auto
bracket will be performed.
2 Take pictures. • Burst mode will not perform as
described if a MultiMediaCard is used
in place of an SD Memory Card. The
reading/writing speed of a
MultiMediaCard is slower than that of
an SD Memory Card.

• Keep pressing the shutter button

fully to activate the burst mode.

44
FZ10-PP.book 45 ページ ２００３年１１月１８日 火曜日 午後１時７分

Playback (basic)
Playback (basic)

Playing Back Pictures

Preparation
• Set the mode dial to [ ]. (P30)

• The setting of the number of files

1 Select the picture. forwarded/rewound at a time varies
2304 depending on the total number of the
100 _ 0001 recorded pictures.
1/19 • When releasing 2/1, the number of
file forwarded begins from 1.
• While forwarding or rewinding a large
number of pictures by holding down
2/1, once release 2/1 before
10:00 DEC. 1.2003 reaching the picture to be played back,
then press 2/1 to forward/rewind
WB pictures until the desired picture
appears.
• In review playback in the recording
RE
VIE W mode or multi playback, the picture
SET
can only be forwarded or rewound one
• Press 2 to play back the previous by one.
picture. ¬Suggestions/Tips ¬
• Press 1 to play back the next
picture. • This camera is based on the DCF
• The picture following the last one is standards (Design rule for Camera
the first picture. File system) which were established
by the Japan Electronics and
ª Fast forwarding/Fast rewinding Information Technology Industries
Association (JEITA).
When you keep pressing 2/1 during • When changing the folder name or file
playback, the file number and the page name on PC, the pictures may not be
number are updated. If you release 2/ played back.
1 when the number of the desired • The file format that can be played back
picture appears, you can play back the with this camera is JPEG. (There are
picture. also pictures that cannot be played
1: Fast forward back in JPEG format.)
2: Fast rewind • When playing back pictures that have
been recorded with other equipment,
• The number of files forwarded/ the picture quality may be deteriorated
rewound at a time depends on how and pictures may not be played back.
long you hold down 2/1. • When playing back a file out of
• The longer you hold down 2/1, the standard, the folder/file number is
more pictures you can forward/rewind indicated by [—] and the screen may
at a time. turn black.
• The interference fringe may appear on
the screen depending on the subject.
This is called moire. This is not a
malfunction.
45
FZ10-PP.book 46 ページ ２００３年１１月１８日 火曜日 午後１時７分

Playback (basic)

9 Pictures Multi Playback

Preparation
• Set the mode dial to [ ]. (P30)

1 Switch to multi screen. 2 Select the pictures.

2304
100 _ 0001 1 2 3
1/19
4 5 6

7 8 9
10:00 DEC. 1.2003 SELECT CANCEL

WB
W T

RE
VIE W
SET

1 2 3 10 11 12

4 5 6

7 8 9
SELECT CANCEL SELECT CANCEL

ª To return to the normal playback

Rotate the zoom lever towards [ ].

W T

• The picture with the number colored in

yellow appears.

46
FZ10-PP.book 47 ページ ２００３年１１月１８日 火曜日 午後１時７分

Playback (basic)

Using the Playback Zoom

Preparation
• Set the mode dial to [ ]. (P30)

ª To delete a picture during the

1 Enlarge the picture.
playback zoom
2X Press the [ ] button.
When the confirmation screen appears,
press 2 to select [YES], and press 4.
(P48)

4X ¬Suggestions/Tips ¬
CANCEL DELETE • The more the picture is enlarged, the
more its quality deteriorates.
W T • The playback zoom may not operate if
pictures have been recorded with
other equipment.

• : 1k>2k>4k>8k>16k
• : 16k>8k>4k>2k>1k
2 Shift the picture.

2X

4X
CANCEL DELETE

WB

RE
VIE W
SET

47
FZ10-PP.book 48 ページ ２００３年１１月１８日 火曜日 午後１時７分

Playback (basic)

Deleting Pictures
Preparation
• Set the mode dial to [ ]. (P30)

ª To delete single picture

1 Select the picture to be deleted.

2304
100 _ 0001
1/19

10:00 DEC. 1.2003

WB

RE
VIE W
SET

• Press 2 to play back the previous

picture.
• Press 1 to play back the next
picture.
2 Delete the picture.

DELETE SINGLE

DELETE THIS PICTURE?

YES NO

SELECT
SET MULTI/ALL

WB WB

RE RE
VIE W VIE W
SET SET

48
FZ10-PP.book 49 ページ ２００３年１１月１８日 火曜日 午後１時７分

Playback (basic)
ª To delete multi pictures

1 Select [MULTI DELETE]. 3 Delete the pictures.

MULTI/ALL DELETE MULTI DELETE

MULTI DELETE DELETE THE PICTURES

ALL DELETE YOU MARKED?
YES NO

SELECT SET CANCEL SELECT SET

WB WB WB

RE RE RE
VIE W VIE W
2 times VIE W
SET SET SET

• It is possible to delete up to
2 Select the pictures to be deleted. 50 pictures all at once.

MULTI DELETE

7 8 9

10 11 12
SELECT DELETE
MARK/UNMARK EXIT MENU

WB WB

RE RE
VIE W VIE W
SET SET

• The selected pictures appear with

[ ]. When 4 is pressed again, the
setting is canceled.
• The icon [ ] blinks red if the
selected picture cannot be deleted.
Cancel the protect setting. (P96)

49
FZ10-PP.book 50 ページ ２００３年１１月１８日 火曜日 午後１時７分

Playback (basic)
ª To delete all pictures ¬Suggestions/Tips ¬
• Once deleted, pictures cannot be
1 Select [ALL DELETE].
recovered. Please double-check
MULTI/ALL DELETE before deleting pictures.
• Pictures that are protected (P96) or
MULTI DELETE not of DCF standards (P45) are not
ALL DELETE deleted.
• Do not turn off the camera while
deleting.
• When the remaining battery power
SELECT SET CANCEL
(P13) is low, use the AC adaptor.
WB WB

RE RE
2 times VIE W VIE W
SET SET

2 Delete all of the pictures.

ALL DELETE

DELETE ALL PICTURES?

YES NO

SELECT SET

WB WB

RE RE
VIE W VIE W
SET SET

50
FZ10-PP.book 51 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (advanced)

Recording pictures (advanced)

About the EXPOSURE Button

ª How to use the [EXPOSURE] button
When pressing the [EXPOSURE] button in Program AE mode [ ], Macro mode
[ ] and A/S/M mode [ ], the operation of the cursor button changes as follows.

Normal Exposure setting mode

Program AE mode/ A/S/M mode
Macro mode

WB
EXPOSURE

WB WB

RE
VI E W
SET
RE RE
VI E W VI E W
SET SET

F4.0 1/30 PROGRAM SHIFT F4.0 1/30

F4.0 1/30

1 Exposure compensation, Recording mode Cursor button

etc. Set the Program shift
2 Self-timer Program AE
with 2/1.
3 Review Macro mode
4 Flash Set the aperture value
5 Program shift setting Aperture-priority
with 3/4.
6 Close the aperture AE
(2/1 is not available.)
7 Set faster shutter speed
8 Open the aperture Shutter-priority Set the shutter speed
9 Set slower shutter speed AE with 2/1.
(3/4 is not available.)

Manual Set the aperture value

with 3/4 and set the
Exposure
shutter speed with 2/1.

• Refer to P35 for the Program shift.

51
FZ10-PP.book 52 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (advanced)

Taking Pictures with Aperture-priority AE

When you want the background to be in sharp focus, set the aperture value to a
higher number. The higher the aperture value, the smaller the aperture opening will
be. For a soft focus background, set the aperture number to a lower number which
corresponds to a larger aperture opening.
Preparation
• Set the mode dial to [ ]. (P30)

¬Suggestions/Tips ¬
1 Select [AE MODE] and set it to [A].
• Refer to P56 for the available range of
REC 1/4 SETUP the aperture value and the shutter
W.BALANCE AUTO speed.
AE AE MODE • The focus range is 0.16 feet (5 cm) – ¶
A S M (Wide) and 6.56 feet (2 m) – ¶ (Tele).
PICT.SIZE 2304 • If the subject is too bright, set to larger
QUALITY aperture value, if too dim, set to
SELECT SET EXIT MENU smaller aperture value.
• The brightness of the screen may
MENU WB WB differ from that of the actual pictures.
Check it using review function or
setting to the playback mode.
RE RE
VIE W VIE W • The ISO sensitivity cannot be set to
SET SET
[AUTO].
• Close the menu by pressing the • When the exposure is not adequate, of
[MENU] button after finishing the the aperture and the shutter speed
setting. values on the screen turn red.
2 Set the aperture value and take
the picture.

A ISO100 2304
1 19

F2.8

WB
EXPOSURE

RE
VIE W
SET

52
FZ10-PP.book 53 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (advanced)

Taking Pictures with Shutter-priority AE

When you want to take a sharp picture of a fast moving subject, set to faster shutter
speed. When you want to create a trail effect, set to slower shutter speed.
Preparation
• Set the mode dial to [ ]. (P30)

¬Suggestions/Tips ¬
1 Select [AE MODE] and set it to [S].
• Refer to P56 for the available range of
REC 1/4 SETUP the aperture value and the shutter
W.BALANCE AUTO speed.
AE AE MODE • The focus range is between 0.16 feet
A S M (5 cm) – ¶ (Wide) and 6.56 feet
PICT.SIZE 2304 (2 m) – ¶ (Tele).
QUALITY • The brightness of the screen may
SELECT SET EXIT MENU differ from that of the actual pictures.
Check it using review function or
MENU WB WB setting to the playback mode.
• You cannot set the following items in
Shutter-priority AE.
RE RE
VIE W VIE W – Slow sync./Red-eye reduction
SET SET
[ ] (P38)
• Close the menu by pressing the – [AUTO] in ISO sensitivity (P74)
[MENU] button after finishing the • When the exposure is not adequate,
setting. the aperture value and the shutter
2 Set the shutter speed and take the speed on the screen turn red.
picture. • When the shutter speed is slow, we
recommend using a tripod.
S ISO100 2304
1 19

1/30

WB
EXPOSURE

RE
VIE W
SET

53
FZ10-PP.book 54 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (advanced)

Taking Pictures with Manual Exposure

Decide the exposure by setting the aperture value and the shutter speed manually.
Preparation
• Set the mode dial to A/S/M mode [ ]. (P30)

1 Select [AE MODE] and set it to [M]. 3 Press the shutter button halfway.

REC 1/4 SETUP M ISO100 2304

W.BALANCE AUTO 1 19
AE AE MODE
A S M
PICT.SIZE 2304
QUALITY
SELECT SET EXIT MENU F4.0 1/125

MENU WB WB

RE RE
VIE W VIE W
SET SET
• Indication for the condition of
• Close the menu by pressing the exposure 1 (manual exposure
[MENU] button after finishing the assistance) appears for about
setting. 10 seconds.
• When the exposure is not
2 Set the aperture value and the
adequate, set the aperture value
shutter speed.
and the shutter speed again.
M ISO100 2304
1 19
4 Take the picture.

M ISO100 2304
1 19

F2.8 1/30

WB
EXPOSURE F5.6 1/125

RE
VIE W
SET

• 3/4: Aperture value

• 2/1: Shutter speed

54
FZ10-PP.book 55 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (advanced)

ª Manual Exposure Assistance

The exposure is
adequate.

Set to faster
shutter speed or
larger aperture
value.

Set to slower
shutter speed or
smaller aperture
value.

• The manual exposure assistance is an

approximation. We recommend taking
pictures and then checking them using
the review function.

¬Suggestions/Tips ¬
• Refer to P56 for the available range of
the aperture value and the shutter
speed.
• The focus range is 0.16 feet (5 cm) – ¶
(Wide) and 6.56 feet (2 m) – ¶ (Tele).
• If the exposure is not adequate, the
aperture value and the shutter speed
turn red when pressing the shutter
button halfway.
• You cannot set the following items in
manual exposure.
– Slow sync./Red-eye reduction
[ ] (P38)
– [AUTO] in ISO sensitivity (P74)
– Exposure compensation (P41)

55
FZ10-PP.book 56 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (advanced)

Aperture Value and Shutter Speed

ª Aperture-priority AE

Available Aperture value (Per 1/3 EV) Shutter Speed (Sec.)

F8.0 1 – 1/2000
F7.3 F6.5 F5.6 1 – 1/1600
F5.2 F4.6 F4.0 1 – 1/1300
F3.7 F3.3 F2.8 1 – 1/1000

ª Shutter-priority AE

Available Shutter Speed (Sec.) (Per 1/3 EV) Aperture value

8 6 5 4
3.2 2.5 2 1.6
1.3 1 1/1.3 1/1.6
1/2 1/2.5 1/3.2 1/4
1/5 1/6 1/8 1/10
1/13 1/15 1/20 1/25 F2.8 – F8.0
1/30 1/40 1/50 1/60
1/80 1/100 1/125 1/160
1/200 1/250 1/320 1/400
1/500 1/640 1/800 1/1000
1/1300 F4.0 – F8.0
1/1600 F5.6 – F8.0
1/2000 F8.0

ª Manual exposure

Available Aperture value (Per 1/3 EV) Available Shutter Speed (Sec.) (Per 1/3 EV)
F2.8 – F8.0 8 – 1/1000
F4.0 – F8.0 8 – 1/1300
F5.6 – F8.0 8 – 1/1600
F8.0 8 – 1/2000

56
FZ10-PP.book 57 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (advanced)

Taking Pictures using Macro Mode

This mode allows you to take pictures closely focusing on the subject. (E.g. When
taking pictures of flowers.)
You can take pictures with the lens at a distance of 0.16 feet (5 cm) (Wide) from the
subject.
Preparation
• Set the mode dial to [ ]. (P30)

• Normal ¬Suggestions/Tips ¬
6.56 feet • In Macro mode, we recommend using
(2 m)
a tripod.
• When the camera lens is at a distance
0.98 feet
(30 cm) over the available range from the
subject, the subject may not be
focused even if the focus indication
• Macro mode [ ] lights.
6.56 feet • You can also set the Program shift.
(2 m)
(P35)
• The available flash range is about
0.16 feet
(5 cm) 1.31 feet (40 cm) – 13.1 feet (4 m).
(When setting to ISO AUTO)

2304
1 19

57
FZ10-PP.book 58 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (advanced)

Taking Pictures using Portrait Mode

This mode allows you to make the subject stand out from the unfocused background
and adjust the exposure and the hue.
Preparation
• Set the mode dial to [ ]. (P30)

ª Technique for Portrait mode ¬Suggestions/Tips ¬

To make this mode more effective, • This mode is suitable for outdoors in
rotate the zoom lever to Tele as far as the daytime.
possible to be close to the subject, and • [AUTO] setting in white balance works
then select the background which is far best when recording outdoors in the
from the camera. daytime. When using indoors, the hue
may change.
• You can change the white balance
2304
setting. (P67)
1 19
• When you want to change the
exposure or the hue, compensate the
exposure of adjust the picture quality.

58
FZ10-PP.book 59 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (advanced)

Taking Pictures using Sports Mode

This mode allows you to take pictures of a fast moving subject. (E.g. When taking
pictures of outdoor sports.)
Preparation
• Set the mode dial to [ ]. (P30)

ª Technique for Sports mode ¬Suggestions/Tips ¬

To record actions of the subject as if it • This mode is suitable for outdoors in
were still, the shutter speed becomes the daytime, keeping 16.4 feet (5 m) or
faster than usual. This mode is more more away from the subject.
effective when taking pictures on a clear • [AUTO] setting in white balance works
day. best when recording outdoors in the
daytime. When using indoors, the hue
may change.
2304
• You can change the white balance
1 19
setting. (P67)

59
FZ10-PP.book 60 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (advanced)

Taking Pictures using Panning Mode

The Panning Mode allows you to follow the motion of a moving subject. This special
effect allows the subject to be in sharp focus while the background will show some
motion blur.
Preparation
• Set the mode dial to [ ]. (P30)
• Set to burst mode. (P44)
• Prefocus on the subject. (P66)

ª Technique for Panning mode • Be careful of the following:

To achieve good pictures in panning – Use the Viewfinder. (P27)
– Select the subject with quick
mode, pick a horizontal plane – and then
motion.
pan as you fire shots.
– Be as close to the subject as
possible.
– Prefocus to the point where the
subject will come. (P66)
– Use this mode with burst mode
(P44). Select the best picture from
the pictures taken.
1 Move the camera smoothly while
2304
tracking a subject in motion.
2 Press the shutter button while
1 19
moving the camera.
3 Keep moving the camera
continuously.

60
FZ10-PP.book 61 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (advanced)

¬Suggestions/Tips ¬
• In panning mode, the shutter speed
becomes slower than usual to achieve
the panning effect. As a result, jitter
can easily occur.
• Panning function does not work well in
the following situations.
– Very bright scenes such as daytime
in summer. We recommend using an
ND filter (DMW-LND72, optional).
(P117)
– When the shutter speed is faster
than 1/100th.
– When the subject moves slowly and
the tracking speed is too slow. (The
background cannot be recorded
dynamically.)
• [AUTO] setting in white balance works
best when recording outdoors in the
daytime. When using indoors, the hue
may change.
• You can change the white balance
setting. (P67)

61
FZ10-PP.book 62 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (advanced)

Taking Pictures using Night Portrait Mode

Night Portrait Mode allows you to take pictures against a nighttime landscape. By
using the flash and a slow shutter speed, the picture will show the subject and the
background brighter than they appear in real life.
Preparation
• Set the mode dial to [ ]. (P30)

ª When taking picture of only a

2304 landscape at night
1 19
• Without the flash, the shutter speed
will be about 8 seconds at maximum.
The shutter speed is suitable for taking
pictures of nightscapes only.
• The focus range is 16.4 feet (5 m) – ¶.

¬Suggestions/Tips ¬
ª Technique for Night portrait mode
• Be sure to close the flash when you do
• Open the flash. (P38)
not use the flash.
• Since the shutter speed becomes slow
• Flash setting is fixed to Slow sync./
(max. about 1 sec.), we recommend
Red-eye reduction [ ].
using a tripod.
• You can change the white balance
• Keep the subject still for about
setting. (P67)
1 second after taking a picture.
• The shutter may be kept closed
• The subject should be positioned
(max. about 8 seconds) after taking a
within the available flash range
picture with slow shutter speed, but it
[1.31 feet (40 cm) – 6.56 feet (2 m)].
is not a malfunction.
(Fixed to ISO100)
• When you take pictures in dark places,
• We recommend rotating the zoom
noises may become visible.
lever to Wide.
To avoid noises, we recommend
• The focus range is 3.28 feet (1 m) – ¶.
setting each item on [PICT.ADJ.] to
[LOW]. (P79)

62
FZ10-PP.book 63 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (advanced)

Recording Motion Images

You can record motion images with audio.
Preparation
• Set the mode dial to [ ]. (P30)

1 Select [MOTION RATE]. 2 Press the shutter button halfway.

REC 1/2 SETUP

MOTION RATE
30fps 10fps
1 35S
C AFCONT.AF OFF
D.ZOOM OFF
STABILIZER MODE1

SELECT SET EXIT MENU

MENU WB WB

• When the subject is focused, the

RE
VIE W
RE
VIE W
focus indication 1 lights.
SET SET
3 Press the shutter button fully to
• [30fps]:
start the recording.
The motion of recorded image is
smooth, but the file size is large.
• [10fps]: 1 35S
The file size is smaller so you can
record motion images for a longer
time.
• fps (frame per second); This
means the number of frames used
in 1 second.
• Close the menu by pressing the
• The audio
[MENU] button after finishing the
recording starts
setting.
simultaneously
from the built-in
microphone 2
of the camera.
• By pressing the shutter button fully
again, the recording stops.
• If the memory of the card becomes
full during recording, the recording
stops automatically.

63
FZ10-PP.book 64 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (advanced)

ª Available recording time

SD Memory Motion rate

Card Capacity 10fps 30fps
16 MB 75 seconds 25 seconds
32 MB 160 seconds 55 seconds
64 MB 350 seconds 120 seconds
128 MB 720 seconds 240 seconds
256 MB 1450 seconds 480 seconds
512 MB 2950 seconds 1020 seconds
• The remaining recording time appears on the screen.
(It is an approximation.)
• The recordable time is an approximation.

¬Suggestions/Tips ¬
• The picture size is fixed to 320k240 pixels.
• The motion images cannot be recorded without audio.
• If using the MultiMediaCard, after recording motion images, the card access
indication may appear for a while, but this is not a malfunction.
• After recording starts, the auto focus/zoom/aperture values are fixed (with the first
frame).
• Recording could suddenly stop depending on the type of the card when recording
motion images.
• When the motion images recorded with this camera is played back on other
equipment, the quality of pictures and sounds may be deteriorated or they may not
be played back.
• The motion images recorded with setting [MOTION RATE] to [30fps] cannot be
played on the camera which does not support [30fps] of motion rate.
• The review function cannot be used.
• The stabilizer function can be set to only [MODE1].

64
FZ10-PP.book 65 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (advanced)

Taking Pictures with Manual Focus

Use this function when you want to fix the focus.
Preparation
• Set the mode dial except for [ ]. (P30)

1 Select [MF ASSIST] from the 2 Slide the focus switch to [MF] and
[SETUP] menu (in the recording rotate the MF ring 1 to focus on
mode) (P26) and set it to [ON]. the subject.

REC SETUP 2/3

MF ASSIST
OFF ON
NO.RESET FOCUS
RESET
AF
CLOCK SET MF

SELECT SET EXIT MENU

WB
MENU

RE
• AF: Auto focus
VIE W
SET
• MF: Manual focus
• 4: One shot AF
WB WB

3 The MF assistance appears on the

center of the screen.
RE RE
VIE W VIE W
SET SET
P 2304
• Close the menu by pressing the 1 MF 19
[MENU] button after finishing the
setting.

• You can also set [MF ASSIST] to

[OFF] on the [SETUP] menu (in the
recording mode).
• When you stop rotating the MF
ring, the MF assistance disappears
about 2 seconds after.

65
FZ10-PP.book 66 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (advanced)

ª Technique for Manual focus ª Prefocus
The subject is focused. This is a technique to focus on the point
to take pictures in advance when it is
difficult to focus on the subject with auto
focus due to its quick motion. (E.g.
Panning mode [ ]) (P60)
This function is suitable when the
distance between the camera and the
subject is certain.

¬Suggestions/Tips ¬
• You can also record with manual focus
in Motion image mode [ ]. When
starting the recording, the focus is
fixed.
The subject is unfocused. • When you focus on the subject in
1 Rotate the MF ring slowly. If the Wide, the focus may not be adequate
subject is focused, rotate it a little in Tele. In this case, focus on the
more. subject again.
2 Finely focus on the subject while • When you zoom in the subject after
rotating the MF ring in the reverse focusing in Tele, the focus may
direction. fluctuate. Focus on the subject again.
• When setting the manual focus, you
ª One shot AF cannot set the continuous AF.
• The MF assistance only appears in
You can focus on the subject with auto
optical zoom range.
focus by sliding down the focus switch to
[4] in MF mode.
This is convenient for prefocus.

FOCUS

AF
MF

66
FZ10-PP.book 67 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (advanced)

Setting the White Balance

In certain situations, the color white may appear slightly reddish or bluish. This can
occur when shooting under early or late day sunlight, on a cloudy day, or under
halogen lighting. By using the manual White Balance feature you can achieve a
more accurate reproduction of the color white.
Preparation
• Set the mode dial except for [ ]/[ ]. (P30)

• Close the menu by pressing the

1 Select [W.BALANCE] and set the
[MENU] button after finishing the
desirable mode.
setting.
REC 1/4 SETUP
W.BALANCE
WB
AUTO
PICT.SIZE 2304
QUALITY
SPOT MODE OFF

SELECT SET EXIT MENU

MENU WB WB

RE RE
VIE W VIE W
SET SET

• [AUTO]:
for setting the white balance
automatically (auto white balance)
•[ ] (Daylight):
for recording outdoors on a bright
day
•[ ] (Cloudy):
for recording under a cloudy and
shady sky
•[ ] (Halogen):
for recording under halogen lighting
• [ WB ] (Flash):
for taking a picture with photo flash
only
•[ ] (White set):
for manual setting (Read the
following page where the manual
setting is explained in detail.)

67
FZ10-PP.book 68 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (advanced)

Use of auto white balance adjustment in
inappropriate lighting conditions may
result in reddish or bluish pictures.
Where the subject is surrounded by
many light sources, auto white balance
adjustment may not operate properly.
In this case, set the white balance to the
mode except [AUTO] manually.

1 The range that is controlled by the

auto white balance adjustment mode
of this camera
2 Blue sky
3 Cloudy sky (Rain)
4 TV screen
5 Sunlight
6 White fluorescent light
7 Incandescent light bulb
8 Sunrise and sunset
9 Candlelight
2)
3)
4)
5)
1) 6)

7)

8)
9)

KlKelvin Color Temperature

68
FZ10-PP.book 69 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (advanced)

Setting the White Balance manually (White set)

Preparation
• Set the mode dial except for [ ]/[ ]. (P30)

1 Select [W.BALANCE] and set to ¬Suggestions/Tips ¬

[ ]. • When setting the white balance to the
REC 1/4 SETUP mode except for [AUTO], you can
finely adjust the white balance. (P70)
W.BALANCE • The setting of the white balance is
WB

applied to the other recording modes.

PICT.SIZE 2304
• In Motion image mode [ ], the white
QUALITY
balance is fixed to [AUTO].
SPOT MODE OFF
• When taking a picture with the flash,
SELECT SET EXIT MENU the white balance will be automatically
adjusted [except for [ ] (Daylight)
MENU WB WB
and [ WB ] (Flash)], but the white
balance may not be properly adjusted
RE RE
when the photo flash is insufficient.
VIE W VIE W
SET SET

2 (Only when setting the white

balance again) Press 1.
3 Aim the camera at a sheet of white
paper 1 or similar object so that it
completely fills the frame to white
on the screen and press the
shutter button fully.

• Close the menu by pressing the

[MENU] button after finishing the
setting.

69
FZ10-PP.book 70 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (advanced)

Finely Adjusting the White Balance

If you cannot acquire the desirable hue with white balance because of too many
different light sources, etc., adjust the fine white balance as follows.
Preparation
• Set the mode dial except for [ ]/[ ]. (P30)
• Set the white balance to [ ]/[ ]/[ ]/[ WB
]/[ ]. (P67)

1 Press 3 until [ WB ADJUST.] 2 Adjust the white balance.

appears.
WB ADJUST.
WB ADJUST.
RED BLUE
RED BLUE

SELECT EXIT
SELECT EXIT
WB

WB

RE
VIE W
RE SET
VIE W
SET • 1 [BLUE]: Press when the hue is
reddish.
• 2 [RED]: Press when the hue is
bluish.
• Close the function by pressing 4
after finishing the adjustment.

¬Suggestions/Tips ¬
• The white balance icon turns red or
blue.
• You can set the value independently
for each of the modes in white
balance.
• When you set the white balance using
the White set [ ], the adjustment
level is set to “0”.
• The adjusted picture will be close,
though may not be identical to the
actual picture.

70
FZ10-PP.book 71 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (advanced)

Changing the Picture Size

Preparation
• Set the mode dial except for [ ]/[ ]. (P30)

¬Suggestions/Tips ¬
1 Select [PICT.SIZE] and set the
picture size. • In Motion image mode [ ], the
picture size is fixed to 320k240 pixels.
REC 1/4 SETUP • The smaller the picture size
W.BALANCE AUTO (640k480) you select, the more
PICT.SIZE pictures you can store on the card. In
2304 1600 1280 640 addition, a small file size allows you to
QUALITY attach the picture to an e-mail or post
SPOT MODE OFF it on a web site more easily.
SELECT SET EXIT MENU • If you select a larger picture size
(2304k1728), the printed picture will
MENU WB WB be clearer, especially with larger sized
prints.
• If you playback pictures recorded
RE RE
VIE W VIE W using [HDTV] mode on a
SET SET
High-Definition TV, (HDTV has 16:9
• [2304]: 2304k1728 pixels aspect) the picture quality will be
• [1600]: 1600k1200 pixels higher. An SD Memory Card can be
• [1280]: 1280k960 pixels played on TVs with an SD Memory
• [640]: 640k480 pixels Card slot.
• [HDTV]: 1920k1080 pixels
• Close the menu by pressing the
[MENU] button after finishing the
setting.

71
FZ10-PP.book 72 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (advanced)

Changing the Quality

“Quality” refers to the amount each image is compressed. Lower compression
results in superior picture quality. Higher compression allows you to store more
images on your SD Memory card.
Preparation
• Set the mode dial except for [ ]/[ ]. (P30)

¬Suggestions/Tips ¬
1 Select [QUALITY] and set the
quality. • It may happen that pictures appear like
a mosaic depending on the subject or
REC 1/4 SETUP the recording condition.
W.BALANCE AUTO • The number of recordable pictures
PICT.SIZE 2304 depends on the subject.
QUALITY • The number of remaining frames may
not correspond with recorded frames.
SPOT MODE OFF • Refer to P126 for the number of
SELECT SET EXIT MENU recordable pictures.

MENU WB WB

RE RE
VIE W VIE W
SET SET

• : Fine (Low compression)

It gives priority to picture quality to
record high quality pictures.
• : Standard
(High compression)
It gives priority to the number of
recordable pictures and records
standard quality pictures.
• Close the menu by pressing the
[MENU] button after finishing the
setting.

72
FZ10-PP.book 73 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (advanced)

Taking Pictures using Spot Mode

When using Spot mode, the size of the area used to calculate the focus and
exposure is decreased. It is useful when you may be shooting through a group of
people and want to designate where in the group the camera will calculate the
exposure.
Preparation
• Set the mode dial except for [ ]/[ ]. (P30)

1 Select [SPOT MODE] and set it to 3 Move the camera to compose the
picture fixing the focus on the
[ON].
subject and take the picture.
REC 1/4 SETUP
P 2304
W.BALANCE AUTO 1 19
PICT.SIZE 2304
QUALITY
SPOT MODE
OFF ON

SELECT SET EXIT MENU

F2.8 1/25

MENU WB WB • You can set suitable AF/AE in more

limited areas.
RE RE
VIE W VIE W
¬Suggestions/Tips ¬
SET SET

• Close the menu by pressing the • When the subject is dark, it may not be
[MENU] button after finishing the focused properly.
setting. • Background may become dark or
whitish depending on the subject
2 Aim the spot AF area to the
because the exposure is set
subject and press the shutter
appropriately in the spot AF area.
button halfway for the AF/AE lock.

P 2304
1 19

F2.8 1/25

• The spot AF area 1 and spot

metering target 2 appear.

73
FZ10-PP.book 74 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (advanced)

Setting ISO Sensitivity

The ISO setting sets the cameras sensitivity to light. The ISO setting can be
increased when you need to take pictures in places where a flash may not be
allowed. The overall picture quality will decrease slightly as the ISO setting is
increased.

ISO sensitivity 50 400

Use in bright places
Suitable Not suitable
(E.g. outdoors)
Use in dark places Not suitable Suitable
Shutter speed Slow Fast
Noises Less Increase
Preparation
• Set the mode dial except for [ ]. (P30)

¬Suggestions/Tips ¬
1 Select [SENSITIVITY] and set the
ISO sensitivity. • In Motion image mode [ ], ISO
sensitivity is fixed to [AUTO].
REC 2/4 SETUP • To avoid noises, we recommend
SENSITIVITY decreasing the ISO sensitivity or
AUTO 50 100 200 400 setting each item on [PICT.ADJ.] to
AUDIO REC. OFF [LOW]. (P79)
C AF CONT.AF OFF • In A/S/M mode [ ], the ISO
D.ZOOM OFF sensitivity cannot be set to [AUTO].
SELECT SET EXIT MENU

MENU WB WB

RE RE
VIE W VIE W
SET SET

• When setting to [AUTO], the ISO

sensitivity is automatically adjusted
from ISO50 to ISO200 according to
the brightness. (From ISO50 to
ISO400 when using the flash)
• Close the menu by pressing the
[MENU] button after finishing the
setting.

74
FZ10-PP.book 75 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (advanced)

Taking Pictures with Audio

Preparation
• Set the mode dial except for [ ]/[ ]. (P30)

¬Suggestions/Tips ¬
1 Select [AUDIO REC.] and set it to
[ON]. • It is not necessary to keep pressing
the shutter button.
REC 2/4 SETUP • Audio is recorded
SENSITIVITY AUTO from the built-in
AUDIO REC. microphone 1 of
OFF ON the camera.
C AF CONT.AF OFF • When setting to
D.ZOOM OFF auto bracket/burst
SELECT SET EXIT MENU mode, it is not possible to take pictures
with audio.
MENU WB WB • When audio is recorded with each
picture the total number of pictures
that can be stored on each card will be
RE RE
VIE W VIE W slightly decreased.
SET SET

• Close the menu by pressing the

[MENU] button after finishing the
setting.
2 Take the picture.

P 2304
1 19

F2.8 1/25

• 5 seconds after, the audio

recording is stopped automatically.
• If you press the [MENU] button
during the audio recording, it will be
canceled. The audio cannot be
recorded.

75
FZ10-PP.book 76 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (advanced)

Using the Continuous AF

This function allows you to reduce the time required for focusing when pressing the
shutter button halfway.
Preparation
• Set the mode dial except for [ ]. (P30)

¬Suggestions/Tips ¬
1 Select [CONT.AF] and set it to
[ON]. • When setting the manual focus, you
cannot use the continuous AF.
REC 2/4 SETUP • The battery is depleted more quickly
SENSITIVITY AUTO using continuous AF.
AUDIO REC. OFF • It may take time to focus on the
C AF CONT.AF subject after rotating the zoom lever
OFF ON from Wide to Tele or suddenly
D.ZOOM OFF changing the subject from distant one
SELECT SET EXIT MENU to nearby one.
• Press the shutter button halfway again
MENU WB WB when it is difficult to focus on the
subject.
• When pressing the shutter button
RE RE
VIE W VIE W halfway, the motion on the screen may
SET SET
be paused. This is not a malfunction.
• Close the menu by pressing the
[MENU] button after finishing the
setting.
2 Take the picture.

P 2304
_
1 C AF 19

F2.8 1/25

76
FZ10-PP.book 77 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (advanced)

Using the Digital Zoom

Preparation
• Set the mode dial except for [ ]. (P30)

ª Entering the digital zoom range

When you rotate the zoom lever to the
extreme Tele position the on screen
zoom indication may momentarily
pause. This is not a malfunction.
You can enter the digital zoom range to
continuously rotate the zoom lever to
Tele or to release the zoom lever once
and then rotate it to Tele again.

W T

W T

1 Optical zoom
2 Digital zoom

1 Select [D.ZOOM] and set it to [ON]. ¬Suggestions/Tips ¬

REC 2/4 SETUP • It is possible to further magnify a
subject already magnified 12 times
SENSITIVITY AUTO
AUDIO REC. OFF
with the optical zoom by 3 more times
C AF CONT.AF OFF with the digital zoom, thereby reaching
D.ZOOM a maximum of 36 times.
OFF ON • When using the digital zoom the
picture quality becomes deteriorated.
SELECT SET EXIT MENU
• In the digital zoom range, the stabilizer
function may not be effective.
MENU WB WB
• We recommend to use a tripod in the
digital zoom range.
RE
VIE W
RE
VIE W
• The indicated zoom magnification is
SET SET an approximation.
• Close the menu by pressing the
[MENU] button after finishing the
setting.
• When rotating the zoom lever with
setting the [D.ZOOM] to [ON], the
digital zoom indication appears.
(P119)

77
FZ10-PP.book 78 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (advanced)

Using the Color Effect

You can use 3 types of color effects depending on the image of the picture.
Preparation
• Set the mode dial except for [ ]/[ ]. (P30)

1 Select [COL.EFFECT] and set the 2 Take the picture.

color.
P 2304
REC 3/4 SETUP COOL 1 19
COL.EFFECT
OFF COOL WARM B/W
PICT.ADJ.
STABILIZER MODE1
FLIP ANIM.
F2.8 1/25
SELECT SET EXIT MENU

MENU WB WB

RE RE
VIE W VIE W
SET SET
¬Suggestions/Tips ¬
• [COOL]: The picture becomes
• [COOL] is effective when you want to
bluish.
add cold atmosphere to the picture,
• [WARM]: The picture becomes
and [WARM] is effective when you
reddish.
want to express comfortable warmth in
• [B/W]: The picture becomes
the scene.
black and white.
• Close the menu by pressing the
[MENU] button after finishing the
setting.

78
FZ10-PP.book 79 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (advanced)

Adjusting the Quality of the Picture

(Picture Adjustment)
Preparation
• Set the mode dial except for [ ]/[ ]. (P30)

• [CONTRAST]:
1 Select [PICT.ADJ.].
HIGH: Increases the difference
REC 3/4 SETUP between the brightness and
the darkness in the picture.
COL.EFFECT OFF
LOW: Decreases the difference
PICT.ADJ.
between the brightness and
STABILIZER MODE1
FLIP ANIM. the darkness in the picture.
• [SHARPNESS]:
HIGH: The picture is sharply
SELECT SET EXIT MENU
defined.
LOW: The picture is softly
MENU WB WB
focused.
• [SATURATION]:
RE
VIE W
RE
VIE W
HIGH: The colors in the picture
SET SET becomes vivid.
LOW: The colors in the picture
2 Select [CONTRAST], become natural.
[SHARPNESS] and [SATURATION] • Close the menu by pressing the
respectively. [MENU] button 2 times after
finishing the setting.
PICT.ADJ.
CONTRAST ¬Suggestions/Tips ¬
LOW STD. HIGH
• When you take pictures in dark places,
SHARPNESS STD.
noises may become visible.
SATURATION STD.
To avoid noises, we recommend
SELECT SET EXIT MENU setting each item on [PICT.ADJ.] to
[LOW].
WB

RE
VIE W
SET

79
FZ10-PP.book 80 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (advanced)

Using the Optical Image Stabilizer

Preparation
• Set the mode dial except for [ ]. (P30)

¬Suggestions/Tips ¬
1 Select [STABILIZER] and set it.
• In [MODE2], the optical image
REC 3/4 SETUP stabilizer icon turns yellow soon after
COL.EFFECT OFF you turn the camera on to keep the
PICT.ADJ. stabilizer function activated.
STABILIZER • While the optical image stabilizer icon
OFF MODE1 MODE2 is displayed in yellow and if the
FLIP ANIM. camera receives a strong shock, the
SELECT SET EXIT MENU icon may be displayed in yellow for
longer time than usual.
MENU WB WB • While the optical image stabilizer icon
is displayed in yellow, the stabilizer
function may not work sufficiently.
RE RE
VIE W VIE W • While the optical image stabilizer icon
SET SET
is displayed in yellow, the pictures on
• [OFF]: OFF screen also be stabilized. (as same as
When image stabilization is not in [MODE1])
desired or when using a tripod. • The stabilizer function may not work
• [MODE1]: 1 sufficiently in the following cases.
The stabilizer operates – When too much jitter occurs
continuously and can assist during – In digital zoom range
photocomposition. – When taking pictures while following
• [MODE2]: 2 subjects in motion.
The stabilizer function is in standby – When the shutter speed is extremely
and activates at the moment the slow due to nightscape or other
shutter captures the image. This reasons.
mode offers a greater degree of • Refer to P33 for information on jitter.
stabilization.
• Close the menu by pressing the
[MENU] button after finishing the
setting.

80
FZ10-PP.book 81 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (advanced)

Creating Flip Animation

You can create motion image files by arranging pictures taken frame-by-frame.
Preparation
• Set the mode dial except for [ ]/[ ]. (P30)

Example: ª Capturing images

When capturing images of the subject in
sequence moving it little by little and
1 Select [FLIP ANIM.].
aligning the images, the subject looks REC 3/4 SETUP
as if it were moving.
COL.EFFECT OFF
PICT.ADJ.
STABILIZER MODE1
FLIP ANIM.

SELECT SET EXIT MENU

MENU WB WB

RE RE
VIE W VIE W
SET SET

2 Select [IMAGE CAPTURE].

FLIP ANIM.
IMAGE CAPTURE
CREATE MOTION IMAGE
DELETE STILL IMAGES

SELECT SET EXIT MENU

WB

RE
VIE W
SET

81
FZ10-PP.book 82 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (advanced)

ª Creating motion images
3 Capture images for flip animation.
5 Select [CREATE MOTION IMAGE].
P 320
1 8 FLIP ANIM.
REMAIN 92
IMAGE CAPTURE
CREATE MOTION IMAGE
DELETE STILL IMAGES
EXIT MENU
SELECT SET EXIT MENU

MENU WB WB

• You can take up to 100 pictures. RE

VIE W
RE
VIE W
SET SET
4 Check the image.

REVIEW 320
6 Select [FRAME RATE] and set the
1/8 number of frames.

CREATE MOTION IMAGE

FRAME RATE
5fps 10fps
CREATE MOTION IMAGE
SELECT EXIT DELETE

WB
SELECT SET EXIT MENU

WB
RE
VIE W
SET

• You can check the previous or RE

VIE W
following image with 2/1. SET

• Delete unnecessary images with • [5fps]:

[ ] button. 5 frames/sec.
• [10fps]:
10 frames/sec. (The motion images
become smoother.)

82
FZ10-PP.book 83 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (advanced)

ª Playing back a created flip
7 Select [CREATE MOTION IMAGE]
animation
and create a flip animation.
Follow the same procedure as you play
CREATE MOTION IMAGE back motion images. (P89)
FRAME RATE 5fps
CREATE MOTION IMAGE ª Deleting all of still images used
for flip animation
When selecting [DELETE STILL
IMAGES] in flip animation screen, a
SELECT SET EXIT MENU confirmation screen appears. Select
[YES] and then press 4.
WB WB

¬Suggestions/Tips ¬
RE
VIE W
RE
VIE W • Flip animations are created as motion
SET SET image files. (Extension: .MOV)
• The file number appears for about • The number of pixel is 320k240.
1 second after creating a flip • You cannot use pictures with audio,
animation. burst mode and auto bracket.
• Including the created images, the • The images in each frame do not
flip animation is counted as appear in normal review. (P36)
1 animation image. • Flip animations may not be played by
• Close the menu by pressing the other equipment.
[MENU] button 3 times after • The flip animations recorded with
finishing the setting. setting [FRAME RATE] to [5fps]
cannot be played on the camera which
does not support [5fps] of motion rate.
• Audio cannot be recorded on flip
animations. However, you may hear
noises when playing with other
equipment without a mute function.
• The number of recordable images is
an approximation.

83
FZ10-PP.book 84 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (advanced)

Using the External Flash

After installing the optional flash, DMW-FL28, the effective range will be increased
when compared to the camera’s built in flash.
Preparation
• Set the mode dial except for [ ]/[ ]. (P30)

1 Attach the external flash to the hot 2 Select [PRESET] or [MANUAL]

shoe 1 and turn the camera on. and turn the external flash on.

REC 4/4 SETUP

EXT.FLASH
PRESET MANUAL

CONVERSION OFF

SELECT SET EXIT MENU

MENU WB WB

RE RE
VIE W VIE W
SET SET

• Close the menu by pressing the

[MENU] button after finishing the
setting.

ª Switch the external flash setting

• Tighten the lock screw 2 of the
external flash firmly. WB

RE
VIE W
SET

Icon Setting
External flash Forced
or
ON
External flash Forced
or
OFF

84
FZ10-PP.book 85 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (advanced)

ª About PRESET/MANUAL on the • When attaching the external flash, the
external flash shutter speed becomes 1/60th to
1/250th in normal mode, 1 to 1/250th
• When setting to [PRESET] and
attaching the external flash, the in Night portrait mode [ ].
aperture value and the ISO sensitivity • External flash mode is selected when
attaching the external flash to the
are respectively set to [F2.8] and
[ISO100] on the camera regardless of camera even if the external flash is
the recording mode. Set the external turned off. When you are not using the
external flash, detach it or set it to
flash to [AUTO] and set the same
value as the settings on the camera. Forced OFF.
• We recommend setting to [PRESET] • When attaching the external flash, the
built-in flash cannot be activated.
for normal use.
• When setting to [MANUAL], you can • When attaching the external flash, the
set the aperture value, the shutter camera becomes unstable to be put.
• Detach the external flash when
speed and the ISO sensitivity on the
camera even if the external flash is carrying the camera.
attached. • When attaching the external flash, do
not hold only the external flash
• When setting to [MANUAL], set to the
Aperture-priority AE or the manual because it may drop off the camera.
exposure on the camera and then set • When using the external flash and
setting the white balance to [ WB ]
the same aperture value and the ISO
sensitivity on the external flash. (The (Flash), finely adjust the white
external flash cannot control the light balance. (P70)
• If you take pictures close to the subject
adequately due to the change in
aperture value on Shutter-priority AE in Wide, the vignetting effect may
and Program AE.) appear on the bottom of the recorded
picture.
¬Suggestions/Tips ¬ • Read the operating instructions of the
external flash for details.
• Some commercial external flashes
have synchro terminals with
high-voltage or reversed polarity.
Using such external flashes may
cause a malfunction or the camera
may not operate normally.
Be sure to use Panasonic’s external
flash (DMW-FL28).
• If using other external flash units,
please make sure the flash is
designed for use with a digital camera
and the trigger voltage is based on
ISO 10330 (less than 24 volts).
• The available flash range is 32.8 feet
(10 m) in DMW-FL28. (When setting to
ISO100)

85
FZ10-PP.book 86 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (advanced)

Using the Conversion Lens

The tele conversion lens (DMW-LTZ10, optional) allows you to record pictures
zooming in much more (1.5 times). The wide conversion lens (DMW-LWZ10,
optional) allows you take pictures with wider range of focus than usual (0.8 times).
Preparation
• Set the mode dial except for [ ]. (P30)
• Check that the camera is turned off and that the lens is retracted.

1 Remove the lens cap and the lens 3 Turn the camera on and select
ring. [CONVERSION].
REC 4/4 SETUP
EXT.FLASH PRESET
CONVERSION

SELECT SET EXIT MENU

MENU WB WB

2 Attach the tele conversion lens 1 RE

VIE W
RE
VIE W
or wide conversion lens 2. SET SET

4 Set to [WIDE] or [TELE].

CONVERSION

OFF WIDE TELE

SELECT SET

WB WB

RE RE
VIE W VIE W
SET SET
• Rotate the lens slowly and
• [OFF]:
carefully.
When you do not attach the
conversion lens.
• [WIDE]:
When you attach the wide
conversion lens.
86
FZ10-PP.book 87 ページ ２００３年１１月１８日 火曜日 午後１時７分

Recording pictures (advanced)

• [TELE]: ¬Suggestions/Tips ¬
When you attach the tele
• Check if the lens cap is removed
conversion lens.
before attaching the conversion lens.
• Close the menu by pressing the • When using the conversion lens:
[MENU] button after finishing the – The built-in flash cannot be
setting.
activated.
– If you use a tripod, use the tripod
ª Recordable range when using the
adaptor supplied with the
conversion lens
conversion lens, and then fix the
When using the tele conversion lens: tripod to the tripod adaptor.
• Normal: 15.1 feet (4.6 m) – ¶ – If you set [CONVERSION] to
• Macro mode [ ]: [OFF], the performance of the
15.1 feet (4.6 m) – ¶ conversion lens cannot be
When using the wide conversion lens: brought out enough.
• Normal: 0.56 feet (17 cm) – ¶ • When using the tele conversion
• Macro mode [ ]: 0.03 feet (1 cm) – ¶ lens:
– We recommend using a tripod.
– The stabilizer function may not work
Tele conversion lens
sufficiently.
Indication 6k 12k 36k – The focus indication may light due to
Actual the jitter even if the subject is not
9k 18k 54k
magnification focused.
35 mm film – The time required for focusing may
camera 315 mm 630 mm 1890 mm become longer than usual.
equivalent • Read the operating instructions of the
conversion lens for details.
Wide conversion lens
Indication 1k 2k
Actual magnification 0.8k 1.6k
35 mm film camera
28 mm 56 mm
equivalent

• When using the tele conversion lens,

the available zoom range is limited to
6 times or more. Digital zoom is
available.
• When using the wide conversion lens,
the available zoom range is limited
between 1 times and 2 times. Digital
zoom is not available.

87
FZ10-PP.book 88 ページ ２００３年１１月１８日 火曜日 午後１時７分

Playback (advanced)
Playback (advanced)

Playing Back Pictures with Audio

Preparation
• Set the mode dial to [ ]. (P30)

¬Suggestions/Tips ¬
1 Select the picture with audio icon
[ ]. • The picture with audio cannot be
resized (P101) or trimmed (P103).
2304
100 _ 0001
PLAY AUDIO 1/19

10:00 DEC. 1.2003

WB

RE
VIE W
SET

2 Play back the audio.

2304
100 _ 0001
PLAY AUDIO 1/19

10:00 DEC. 1.2003

WB

RE
VIE W
SET

• You can hear audio from the

speaker.
• To adjust the sound volume, refer
to P26.

88
FZ10-PP.book 89 ページ ２００３年１１月１８日 火曜日 午後１時７分

Playback (advanced)

Playing Back Motion Images

Preparation
• Set the mode dial to [ ]. (P30)

ª Fast forwarding/Fast rewinding

1 Select the picture with the motion
image icon [ ]. During motion image playback, continue
pressing 2/1.
1: Fast forward
100 _ 0001 2: Fast rewind
PLAY MOTION 1/19
IMAGE • When releasing the button, it turns to
normal motion image playback.

ª To pause
10:00 DEC. 1.2003
Press 3 during motion image playback.
WB • Press 3 again to cancel pause.

• To adjust the sound volume, refer to

RE
VIE W
P26.
SET

2 Play back the motion images. ¬Suggestions/Tips ¬

• You cannot use the zoom function
10S REMAIN while playing back or pausing motion
images.
• The file format that can be played back
with this camera is QuickTime Motion
JPEG.
• Some QuickTime Motion JPEG files
recorded by a PC or other equipment
may not be played back with this
WB camera.
• When playing back motion images that
have been recorded with other
RE
VIE W
equipment, the quality of images may
SET
be deteriorated or the images may not
• Motion image playback stops and be able to be played back.
the normal playback is restored by • When using a high capacity card, it is
pressing 4. possible that fast rewinding may be
• The icon 1 is corresponding to the slower than usual.
3/4/2/1.

89
FZ10-PP.book 90 ページ ２００３年１１月１８日 火曜日 午後１時７分

Playback (advanced)

Rotating the Picture

You can rotate the recorded pictures in increments of 90°.
This is a convenient function to play back pictures on TV.
Preparation
• Set the mode dial to [ ]. (P30)

• Close the menu by pressing the

1 Select [ROTATE].
[MENU] button after finishing the
PLAY 1/2 SETUP setting.
ROTATE
ª Example
PROTECT
DPOF PRINT When rotating clockwise ( )
SLIDE SHOW
AUDIO DUB.
SELECT SET EXIT MENU
Original
MENU WB WB Picture

¬Suggestions/Tips ¬
RE RE
VIE W VIE W
SET SET • Still pictures can only be rotated in
normal playback. When playing back
2 Select the direction to rotate the rotated pictures in zoom playback or
picture. multi playback, pictures appear in
original angle.
ROTATE
• Rotated pictures appear on a PC only
when an OS or a software compatible
with Exif is installed in the PC.
• Exif is the file format for still pictures,
to which can be added recording
information and other, established by
SELECT SET CANCEL MENU JEITA [Japan Electronics and
Information Technology Industries
WB WB Association].

RE RE
VIE W VIE W
SET SET

•[ ]: The picture rotates

counter-clockwise in
increments of 90°.
•[ ]: The picture rotates
clockwise in increments of
90°.

90
FZ10-PP.book 91 ページ ２００３年１１月１８日 火曜日 午後１時７分

Playback (advanced)

Setting the Picture to be Printed and the

Number of Prints (DPOF Print Setting)
DPOF (Digital Print Order Format) is a system that allows the user to select which
pictures are to be printed on compatible photo printers. DPOF also allows the user
to set how many copies of each picture will be printed. Many commercial photo
printing services now use DPOF. For more information please visit:
http://www.panasonic.co.jp/avc/video/dpof/dpof_110/white_e.htm
Preparation
• Set the mode dial to [ ]. (P30)

ª Single setting/cancel

1 Select [DPOF PRINT]. 3 Select the picture and set the

1/2
number of prints.
PLAY SETUP
ROTATE DPOF SET THIS
PROTECT 1 100 _ 0001
DPOF PRINT 1/19
SLIDE SHOW
AUDIO DUB.
SELECT SET EXIT MENU COUNT 001 DATE DISPLAY
SELECT EXIT MENU
MENU WB WB

WB WB

RE RE
VIE W VIE W
SET SET RE RE
VIE W VIE W
SET SET
2 Select [SINGLE].
• The number of prints can be set
PLAY 1/2 SETUP from 0 to 999.
• The number of prints icon [ 1 ]
ROTATE
appears.
PROTECT SINGLE
• When the number of prints is set to
DPOF PRINT MULTI
SLIDE SHOW CANCEL “0”, DPOF print setting is canceled.
AUDIO DUB. INDEX • Close the menu by pressing the
[MENU] button 2 times after
SELECT SET EXIT MENU
finishing the setting.
WB

RE
VIE W
SET

91
FZ10-PP.book 92 ページ ２００３年１１月１８日 火曜日 午後１時７分

Playback (advanced)
ª Multi setting/cancel

1 Select [DPOF PRINT]. 3 Select the pictures and set the

1/2
number of prints.
PLAY SETUP
ROTATE DPOF SET MULTI
PROTECT 1
DPOF PRINT 7 8 9
SLIDE SHOW
AUDIO DUB. 10 11 12
SELECT SET EXIT MENU COUNT 001 DATE DISPLAY
SELECT EXIT MENU
MENU WB WB

WB WB

RE RE
VIE W VIE W
SET SET RE RE
VIE W VIE W
SET SET
2 Select [MULTI].
• The number of prints can be set
PLAY 1/2 SETUP from 0 to 999.
• The number of prints icon [ 1 ]
ROTATE
appears.
PROTECT SINGLE
• Repeat step 3.
DPOF PRINT MULTI
SLIDE SHOW CANCEL • When the number of prints is set to
AUDIO DUB. INDEX “0”, DPOF print setting is canceled.
• Close the menu by pressing the
SELECT SET EXIT MENU
[MENU] button 2 times after
finishing the setting.
WB WB

RE RE
VIE W VIE W
SET SET

92
FZ10-PP.book 93 ページ ２００３年１１月１８日 火曜日 午後１時７分

Playback (advanced)
ª To cancel all settings

1 Select [DPOF PRINT]. 3 Select [YES] to cancel all settings.

PLAY 1/2 SETUP CANCEL ALL DPOF
ROTATE
PROTECT CANCEL ALL DPOF
DPOF PRINT PRINT SETTINGS?
SLIDE SHOW YES NO
AUDIO DUB.
SELECT SET EXIT MENU SELECT SET

MENU WB WB WB WB

RE RE RE RE
VIE W VIE W VIE W VIE W
SET SET SET SET

• Close the menu by pressing the

2 Select [CANCEL].
[MENU] button after canceling the
PLAY 1/2 SETUP setting.
ROTATE
PROTECT SINGLE
DPOF PRINT MULTI
SLIDE SHOW CANCEL
AUDIO DUB. INDEX
SELECT SET EXIT MENU

WB WB

RE RE
VIE W VIE W
SET SET

93
FZ10-PP.book 94 ページ ２００３年１１月１８日 火曜日 午後１時７分

Playback (advanced)
ª Index setting/cancel

1 Select [DPOF PRINT]. 3 Select [YES] to index setting.

PLAY 1/2 SETUP DPOF INDEX
ROTATE
PROTECT SET INDEX PRINT?
DPOF PRINT
SLIDE SHOW YES NO
AUDIO DUB.
SELECT SET EXIT MENU SELECT SET

MENU WB WB WB WB

RE RE RE RE
VIE W VIE W VIE W VIE W
SET SET SET SET

• Close the menu by pressing the

2 Select [INDEX].
[MENU] button after finishing the
PLAY 1/2 SETUP setting.
ROTATE
PROTECT SINGLE
DPOF PRINT MULTI
SLIDE SHOW CANCEL
AUDIO DUB. INDEX
SELECT SET EXIT MENU

WB WB

RE RE
VIE W VIE W
SET SET

94
FZ10-PP.book 95 ページ ２００３年１１月１８日 火曜日 午後１時７分

Playback (advanced)
ª When the index is already set
¬Suggestions/Tips ¬
• DPOF print setting is a convenient
DPOF INDEX
function when you print pictures with
printers supporting DPOF printing.
SET/CANCEL INDEX
• DPOF is the abbreviation for Digital
PRINT?
Print Order Format. This feature
SET CANCEL NO
allows you to designate which pictures
will be printed.
SELECT SET • The setting of DPOF print will not be
applied to the DPOF setting of
WB WB
Slide Show.
• If the file is not based on the DCF
RE RE
standard, the DPOF print setting
VIE W VIE W
SET SET
cannot be set. DCF is an abbreviation
• Close the menu by pressing the of [Design rule for Camera File
[MENU] button after finishing the system], stipulated by JEITA [Japan
setting. Electronics and Information
Technology Industries Association].
ª To print the date • When setting the DPOF print, this
camera will overwrite any previous
You can set/cancel the printing with the
DPOF print settings made by other
recorded date each press of the
equipment.
[DISPLAY] button when setting the
number of prints.

DPOF SET THIS

1 100 _ 0001
DATE 1/19

COUNT 001 DATE DISPLAY

SELECT EXIT MENU

• The date print icon [ DATE ] appears.

• When you ask photo studios for
printing, be sure to order the printing
of the date. For further information,
ask a photo studio. Depending on the
studio, it may not be printed.

95
FZ10-PP.book 96 ページ ２００３年１１月１８日 火曜日 午後１時７分

Playback (advanced)

Preventing Accidental Erasure of the Picture

Preparation
• Set the mode dial to [ ]. (P30)

ª Single setting/cancel
1 Select [PROTECT]. 3 Select the picture and set/cancel
1/2
the protection.
PLAY SETUP
ROTATE PROTECT THIS
PROTECT 100 _ 0001
DPOF PRINT 1/19
SLIDE SHOW
AUDIO DUB.
SELECT SET EXIT MENU SELECT
SET/CANCEL EXIT MENU
MENU WB WB

WB WB

RE RE
VIE W VIE W
SET SET RE RE
VIE W VIE W
SET SET
2 Select [SINGLE].
• [SET]:
PLAY 1/2 SETUP The protect icon [ ] appears.
• [CANCEL]:
ROTATE
The protect icon [ ] disappears.
PROTECT SINGLE
• Close the menu by pressing the
DPOF PRINT MULTI
SLIDE SHOW CANCEL [MENU] button 2 times after
AUDIO DUB. finishing the setting.
SELECT SET EXIT MENU

WB

RE
VIE W
SET

96
FZ10-PP.book 97 ページ ２００３年１１月１８日 火曜日 午後１時７分

Playback (advanced)
ª Multi setting/To cancel all settings
Perform the same operation as in
[Setting the Picture to be Printed and
the Number of Prints (DPOF Print
Setting)]. (P91– 93)

¬Suggestions/Tips ¬
• While this feature protects the pictures
from accidental erasure, formatting the
card will permanently delete all data.
(P105)
• If you want to delete protected
pictures, cancel the protect setting
first.
• The protect setting may not be
effective in other equipment.
• Sliding the SD Memory Card
Write-Protect switch to [LOCK]
prevents the picture from deletion
even if the protection is not set.
• The audio dubbing cannot be used
with protected pictures. (P100)

97
FZ10-PP.book 98 ページ ２００３年１１月１８日 火曜日 午後１時７分

Playback (advanced)

Playing Back with Slide Show

Preparation
• Set the mode dial to [ ]. (P30)

1 Select [SLIDE SHOW]. 3 Select the following items.

PLAY 1/2 SETUP
ROTATE START
PROTECT DURATION
DPOF PRINT 1SEC. 2SEC. 3SEC. 5SEC.
SLIDE SHOW AUDIO OFF
AUDIO DUB.
SELECT SET EXIT MENU SELECT SET EXIT MENU

MENU WB WB WB

RE RE RE
VIE W VIE W VIE W
SET SET SET

• [DURATION]:
2 Select the type of pictures to play
It can be set among 1, 2, 3 and
back.
5 seconds.
PLAY 1/2 SETUP • [AUDIO]:
By setting it to [ON], the audio of
ROTATE
the pictures with audio can be
PROTECT
played back during Slide Show.
DPOF PRINT
SLIDE SHOW ALL • [DPOF SET] (Only when setting to
AUDIO DUB. DPOF [DPOF]):
You can select the pictures you
SELECT SET EXIT MENU
want to set to the Slide Show.
• [CANCEL ALL] (Only when setting
WB WB
to [DPOF]):
You can cancel the
RE
VIE W
RE
VIE W
DPOF Slide Show setting.
SET SET

• [ALL]:
for playing back all pictures
• [DPOF]:
for playing back the pictures
DPOF Slide Show is set

98
FZ10-PP.book 99 ページ ２００３年１１月１８日 火曜日 午後１時７分

Playback (advanced)
¬Suggestions/Tips ¬
4 Select [START].
• When setting the DPOF Slide Show,
DPOF icon 1 appears on the picture
START in green.
DURATION 1SEC. • When setting the DPOF Slide Show to
AUDIO OFF the picture with DPOF printing, both of
DPOF icon 1 and the number of
prints appear on the picture in green.
SELECT SET EXIT MENU • When only the DPOF printing is set on
the picture, the DPOF icon 1 and the
WB WB number of prints appear in white.

DPOF SET THIS

RE
VIE W
RE
VIE W 100 _ 0001
SET SET 1/19

5 By pressing the [MENU] button,

the Slide Show stops.
SELECT
ª SD Slide Show SET/CANCEL EXIT MENU
If setting the SD Slide Show with the • In motion image playback, Slide Show
[SD Viewer for DSC] which is in the is not available.
supplied CD-ROM, when playing back, • The DPOF setting of Slide Show will
the confirmation screen appears. Select not be applied to the DPOF printing.
[YES] and press 4 to start the SD • DPOF Slide Show cannot be
Slide Show. Select [NO] and press 4 to performed without the DPOF setting of
start normal playback. Slide Show.
• DPOF setting with the [SD Viewer for
DSC] in the supplied CD-ROM is only
for printing. Please set DPOF Slide
Show with this camera to play back
pictures in DPOF Slide Show.
• When setting the DPOF Slide Show,
this camera will overwrite any previous
DPOF settings made by other
equipment.

99
FZ10-PP.book 100 ページ ２００３年１１月１８日 火曜日 午後１時７分

Playback (advanced)

Adding Audio to Recorded Pictures

(Audio Dubbing)
Preparation
• Set the mode dial to [ ]. (P30)

• The audio dubbing cannot be used

1 Select [AUDIO DUB.].
with motion images or protected
PLAY 1/2 SETUP pictures.
ROTATE 3 Stop audio recording.
PROTECT
DPOF PRINT AUDIO 2304

SLIDE SHOW
DUB. 100 _ 0001
AUDIO DUB. 1/19
SELECT SET EXIT MENU

MENU WB WB

STOP
RE RE
VIE W VIE W
WB
SET SET

2 Select the picture and start audio RE

VIE W
recording. SET

AUDIO 2304 • Even if you do not press 4, after

DUB. 100 _ 0001 about 10 seconds the audio
1/19 recording stops automatically.
• Close the menu by pressing the
[MENU] button 2 times after
finishing the setting.
SELECT
START EXIT MENU

WB WB

RE RE
VIE W VIE W
SET SET

• When audio has already been

recorded, the confirmation screen
appears. Press 2 to select [YES],
and press 4 to start audio
recording. (The original audio is
overwritten.)

100
FZ10-PP.book 101 ページ ２００３年１１月１８日 火曜日 午後１時７分

Playback (advanced)

Resizing the Pictures

This function is useful if you want to reduce the file size of the picture, in those cases
when it needs to be attached to an E-mail or uploaded it to a web site.
Preparation
• Set the mode dial to [ ]. (P30)

1 Select [RESIZE]. 3 Select the size and set it.

PLAY 2/2 SETUP RESIZE 2304

RESIZE 100 _ 0001

TRIMMING 2304 1/19
FORMAT 1600

SELECT
SELECT SET EXIT MENU RESIZE EXIT MENU

MENU WB WB WB WB

RE RE RE RE
VIE W VIE W VIE W VIE W
SET SET SET SET

• [1600]: 1600k1200 pixels

2 Select the picture and set it.
• [1280]: 1280k960 pixels
RESIZE 2304 • [640]: 640k480 pixels
100 _ 0001
1/19

SELECT
SET EXIT MENU

WB WB

RE RE
VIE W VIE W
SET SET

101
FZ10-PP.book 102 ページ ２００３年１１月１８日 火曜日 午後１時７分

Playback (advanced)

4 Select [YES] or [NO] and set it.

RESIZE

DELETE ORIGINAL
PICTURE?
YES NO

SELECT SET CANCEL MENU

WB WB

RE RE
VIE W VIE W
SET SET

• When you select [YES], the picture

is overwritten.
• When resized pictures are
overwritten, they cannot be
restored.
• Close the menu by pressing the
[MENU] button 2 times after
finishing the resizing.

¬Suggestions/Tips ¬
• The following pictures cannot be
resized.
– Pictures not over 640k480 pixels
– Pictures recorded with setting the
picture size to [HDTV]
– Motion images
– Flip animation
– Pictures with audio
– Rotated pictures (You can resize
them if you turn them back.)
• It may not be possible to resize the
pictures recorded with other
equipment.

102
FZ10-PP.book 103 ページ ２００３年１１月１８日 火曜日 午後１時７分

Playback (advanced)

Trimming the Pictures

Preparation
• Set the mode dial to [ ]. (P30)

2 Select the picture to trim.

TRIMMING 2304
100 _ 0001
1/19

SELECT
SET EXIT MENU

WB WB

RE RE
VIE W VIE W
SET SET

3 Enlarge or decrease the picture.

TRIMMING 2304
100 _ 0001
1 Select [TRIMMING]. 1/19
PLAY 2/2 SETUP
RESIZE
TRIMMING
FORMAT ZOOM EXIT MENU

W T
SELECT SET EXIT MENU

MENU WB WB

RE RE
VIE W VIE W
SET SET

103
FZ10-PP.book 104 ページ ２００３年１１月１８日 火曜日 午後１時７分

Playback (advanced)

¬Suggestions/Tips ¬
4 Shift the picture and press the
shutter button fully to set. • The following pictures cannot be
trimmed.
TRIMMING 2304 – Pictures equal to or smaller than
100 _ 0001 640k480 pixels
1/19 – Pictures recorded with setting the
picture size to [HDTV]
– Motion images
ZOOM – Flip animation
TRIM:SHUTTER EXIT MENU – Pictures with audio
– Rotated pictures (You can trim them
WB if you rotate them back.)
• It may not be possible to trim pictures
recorded with other equipment.
RE
VIE W • The picture size of the trimmed
SET
pictures may become smaller than that
5 Select [YES] or [NO] and set it. of the original one depending on the
cut size.
TRIMMING • The picture quality of the trimmed
picture may be deteriorated.
DELETE ORIGINAL
PICTURE?
YES NO

SELECT SET CANCEL MENU

WB WB

RE RE
VIE W VIE W
SET SET

• When you select [YES], the picture

is overwritten.
• When trimmed pictures are
overwritten, they cannot be
restored.
• Close the menu by pressing the
[MENU] button 2 times after
finishing the trimming.

104
FZ10-PP.book 105 ページ ２００３年１１月１８日 火曜日 午後１時７分

Playback (advanced)

Formatting the Card

Preparation
• Set the mode dial to [ ]. (P30)

¬Suggestions/Tips ¬
1 Select [FORMAT].
• Usually, it is not necessary to format
PLAY 2/2 SETUP the card (initializing). Format the card
RESIZE when the message [MEMORY CARD
TRIMMING ERROR] appears.
FORMAT • If the card has been formatted by a PC
or other equipment, format the card on
the camera again.
SELECT SET EXIT MENU • After formatting, recorded pictures and
any other data cannot be recovered.
MENU WB WB • If the card is formatted all images
and data will be permanently
erased. They cannot be reclaimed.
RE RE
VIE W VIE W If any important pictures are on the
SET SET
card, please copy them to your PC
2 Select [YES] to format. before proceeding.
• During formatting, do not turn the
FORMAT camera off.
• When the remaining battery power
DELETE ALL DATA (P13) is low, use the AC adaptor.
ON THE MEMORY CARD? • If the card is protected, you cannot
YES NO format the card.
• If the card cannot be formatted,
SELECT SET consult your nearest servicenter.

For USA assistance, please call: 1-800-272-7033

WB WB or send e-mail to : digitalstillcam@panasonic.com

For Canadian assistance, please call:

RE
VIE W
RE
VIE W
1-800-561-5505 or visit us at www.panasonic.ca
SET SET

105
FZ10-PP.book 106 ページ ２００３年１１月１８日 火曜日 午後１時７分

Playback (advanced)

Playing Back Pictures with a TV Screen

ª Playing back pictures with A/V cable (supplied)
• Turn the camera and the TV off.

A/V
OUT

USB

1 Connect the A/V cable to the ª Playback pictures on TV with SD

[A/V OUT] socket of the camera. Memory Card slot

2 Connect the A/V cable to the video An SD Memory Card can be played on
input and the audio input sockets TVs with an SD Memory Card slot.
of the TV. If you playback pictures recorded using
• Yellow: to the video input socket [HDTV] mode on a High-Definition TV,
• White: to the audio input socket (HDTV has 16:9 aspect) the picture
quality will be higher.
3 Turn the TV on and select external
input. ¬Suggestions/Tips ¬
4 Turn the camera on and then set • When connecting to a TV, we
the mode dial to Playback mode recommend using the AC adaptor as
[ ]. the power source.
• Use the supplied A/V cable only.
ª Viewing pictures in other • Read the TV operating instructions
countries too.
When setting [VIDEO OUT] on the
menu, you can view pictures on a TV in
other countries (regions) which use the
NTSC or PAL system.
• Even if you set menu selection for
[VIDEO OUT] to [PAL], the output
signal is still NTSC in the recording
mode.

106
FZ10-PP.book 107 ページ ２００３年１１月１８日 火曜日 午後１時７分

Playback (advanced)

Before Connecting with USB Connection

Cable
Select the USB communication system according to the OS of your PC or your
printer before connecting them to the camera with the USB connection cable
(supplied).
Set the items on [USB MODE] in the [SETUP] menu. (P26)

1 Select [USB MODE]. 2 Select [Mass Storage] or [PTP].

(In the recording mode)

REC SETUP 3/3 USB MODE

USB MODE
USB
LANGUAGE ENG
Direct-Print PictBridge
Mass Storage PTP

SELECT SET EXIT MENU SELECT SET

WB WB WB
MENU

RE RE RE
VIE W VIE W VIE W
SET SET SET

WB WB

RE RE
VIE W VIE W
SET SET

Printer to be
USB mode PC to be connected
connected
Mass Storage Windows® XP Home Edition, Printers supporting
(USB Direct-Print) Windows XP Professional, Windows USB Direct-Print.
2000 Professional, Windows Me,
Windows 98/98 SE or Mac OS X
(10.1 or above), Mac OS 9.x
PTP Windows XP Home Edition, Windows Printers supporting
(PictBridge) XP Professional or Mac OS X PictBridge.

107
FZ10-PP.book 108 ページ ２００３年１１月１８日 火曜日 午後１時７分

Playback (advanced)
ª When using Windows 2000 Professional, Windows Me, Windows 98/98 SE
or Mac OS 9.x
• When connecting the camera to a PC, do not set [USB MODE] to [PTP].
(When the camera is shipped, [Mass Storage] is selected.)
• When using [Mass Storage] on Windows 98/98 SE, install the USB driver before
connecting. (When using Windows Me/2000/XP, Mac OS 9.x and Mac OS X, you
do not have to install the USB driver.)
• When connecting to the PC which includes the
USB MODE
above-mentioned OS with setting the [USB MODE] to [PTP],
the messages shown on the right appear on the LCD
monitor of the camera. PTP

The following messages appear for each OS on the display of the PC. Select
[Cancel] to close the window and disconnect the PC.

OS Message
Windows 2000 Professional [Welcome to the Found New Hardware
Wizard]
Windows Me [New Hardware Found]>
Windows 98/98 SE [Add New Hardware Wizard]
(When you connect to the PC more than
2 times, only [Add New Hardware Wizard]
appears.)
Mac OS 9.x [Software needed for the USB device
“DMC-FZ10” is not available. Would you like to
look for the software on the Internet?]

108
FZ10-PP.book 109 ページ ２００３年１１月１８日 火曜日 午後１時７分

Playback (advanced)

Connecting to a PC (Mass Storage)

A/V
OUT

USB

¬Suggestions/Tips ¬
1 Turn the camera on and then set
[USB MODE] to [Mass Storage]. • When connecting to a PC, we
(P107) recommend using the AC adaptor as
the power source.
2 Connect the camera to a PC via • If the remaining battery power
the USB connection cable becomes low during communication,
(supplied). the power indicator blinks and the
alarm beeps. In this case, stop the
communication. Then turn the camera
off and charge the battery.
ACCESS
• When connecting to a PC, pictures
and sounds are not output from the
[Windows] [A/V OUT] socket.
• Use the supplied USB connection
The drive appears on the
[My Computer] folder. cable only.
• If it is the first time for you to
connect the camera to a PC, the
required driver is installed
automatically so that the camera
can be recognized by the Windows
Plug and Play, then it appears on
the [My Computer] folder.
[Macintosh]
The drive is shown on the screen.

109
FZ10-PP.book 110 ページ ２００３年１１月１８日 火曜日 午後１時７分

Playback (advanced)

Connecting to a PC (PTP)
Do not follow the setting below on the OS except for Windows XP and Mac OS X.

A/V
OUT

USB

[Macintosh]
1 Turn the camera on and then set
You can read pictures with image
[USB MODE] to [PTP]. (P107)
capture or iPhoto.
2 Connect the camera to a PC via
the USB connection cable ¬Suggestions/Tips ¬
(supplied). • Refer to P108 carefully when
connecting to the OS except for
Windows XP and Mac OS X with
setting [USB MODE] to [PTP].
ACCESS
• When connecting to a PC, we
recommend using the AC adaptor as
the power source.
[Windows]
• If the remaining battery power
The camera icon appears on the
becomes low during communication,
[My Computer] folder.
the power indicator blinks and the
• If it is the first time for you to
alarm beeps. In this case, stop the
connect the camera to a PC, the
communication. Then turn the camera
required driver is installed
off and charge the battery.
automatically so that the camera
• When connecting to a PC, pictures
can be recognized by the Windows
and sounds are not output from the
Plug and Play, then the camera
[A/V OUT] socket.
icon appears on the [My Computer]
• It may take time to display the
folder.
communication screen depending on
the PC.

110
FZ10-PP.book 111 ページ ２００３年１１月１８日 火曜日 午後１時７分

Playback (advanced)
• You can only load pictures from the
camera and cannot write them on the
card or delete them.
• Use the supplied USB connection
cable only.
• When there are 1000 or more pictures
on the card, the pictures may not be
imported.
• When the PC recovers from the
standby mode while connecting it to a
camera with USB connection cables,
they may not properly communicate
each other.

111
FZ10-PP.book 112 ページ ２００３年１１月１８日 火曜日 午後１時７分

Playback (advanced)

Connecting to a Printer
By connecting the camera directly to a printer supporting PictBridge or USB
Direct-Print via the USB connection cable (supplied), you can select the pictures to
be printed or start printing.

A/V
OUT

USB

1 Turn the camera on and then set ¬Suggestions/Tips ¬

the [USB MODE] to [PTP] • Ask the manufacturer of the printer
(PictBridge) or [Mass Storage] about the corresponding models.
(USB Direct-Print). (P107) (Read the printer operating
2 Turn on a printer. instructions too.)
• If the remaining battery power
3 Connect the camera to the printer becomes low during communication,
via the USB connection cable the power indicator blinks and the
(supplied). alarm beeps. In this case, stop the
communication. Then turn the camera
off and charge the battery.
• When connecting to a printer, we
recommend using the AC adaptor as
the power source.
• Disconnect the USB connection cable
and DC cable after printing.
• Use the supplied USB connection
cable only.

112
FZ10-PP.book 113 ページ ２００３年１１月１８日 火曜日 午後１時７分

Playback (advanced)

Using a Printer (PictBridge)

Preparation
• Connect the camera to a printer. (P112)
• Set the paper size and print quality. (Read the printer operating instructions.)

ª Single picture

1 Select [SINGLE PICTURE]. 3 Select [YES] and print.

PictBridge PictBridge
PLS CHECK THE PRINTER
START PRINTING?
SINGLE DPOF COUNT 1
PICTURE PICTURE
YES NO

SET COUNT DATE DISPLAY

SELECT SET SELECT SET

WB WB WB WB

RE RE RE RE
VIE W VIE W VIE W VIE W
SET SET SET SET

• The screen shown in step 2 • Press the [DISPLAY] button to print

appears when DPOF print is not the date. (Only when connecting to
set or the printer does not support the printer supporting to printing
DPOF print. the date.)
• Press 3 and then press 2/1 to
2 Select the picture to print.
set the number of prints. Press 4
PictBridge 2304 to print pictures.
100 _ 0001 • Press the [MENU] button to cancel
1/19 printing.
PLEASE SELECT
THE PICTURE TO PRINT

SELECT PRINT

WB WB

RE RE
VIE W VIE W
SET SET

113
FZ10-PP.book 114 ページ ２００３年１１月１８日 火曜日 午後１時７分

Playback (advanced)
Preparation
• Connect the camera to a printer. (P112)
• Set the DPOF print with this camera in advance. (P91)
• Set the paper size and print quality. (Read the printer operating instructions.)

ª DPOF picture

1 Select [DPOF PICTURE]. 2 Select [YES] and print.

PictBridge PictBridge
PLS CHECK THE PRINTER
START PRINTING?
SINGLE DPOF
PICTURE PICTURE
YES NO
DATE DISPLAY
SELECT SET SELECT SET

WB WB WB WB

RE RE RE RE
VIE W VIE W VIE W VIE W
SET SET SET SET

• Press the [MENU] button, and you • Press the [DISPLAY] button to print
can change the DPOF print setting. the date. (Only when connecting to
(P91) the printer supporting to printing
• When printing under the new the date.)
settings, disconnect the USB • Press the [MENU] button to cancel
connection cable and connect it to printing.
the printer again.

¬Suggestions/Tips ¬
• When the total number of prints becomes 1000 or more, the number of remaining
pictures may appear as [---] on the screen.
• When connecting to a printer not supporting DPOF, DPOF printing cannot be set.
(The DPOF print selecting screen does not appear.)
• Do not disconnect the USB connection cable when the cable disconnection
warning icon [ ] is indicated.
• When the [¥] indication lights in yellow during printing, check if there is no
malfunction on the printer.
• When the printer does not support the date printing by DPOF setting, the date may
not be printed as it is on date setting in DPOF setting.
• When you do not set the date print setting, also check the date print setting on the
printer.

114
FZ10-PP.book 115 ページ ２００３年１１月１８日 火曜日 午後１時７分

Playback (advanced)

Using a Printer (USB Direct-Print)

Preparation
• Connect the camera to a printer. (P112)
• Set the paper size and print quality. (Read the printer operating instructions.)

ª Single picture

1 Select [SINGLE PICTURE]. 3 Select [YES] and print.

DIRECT PRINT DIRECT PRINT

PLS CHECK THE PRINTER
START PRINTING?
SINGLE DPOF COUNT 1
PICTURE PICTURE
YES NO

SET COUNT DATE DISPLAY

SELECT SET SELECT SET

WB WB WB WB

RE RE RE RE
VIE W VIE W VIE W VIE W
SET SET SET SET

• The screen shown in step 2 • Press the [DISPLAY] button to print

appears when DPOF print is not the date.
set. • Press 3 and then press 2/1 to
set the number of prints. Press 4
2 Select the picture to print.
to print pictures.
DIRECT PRINT 2304 • Press the [MENU] button to cancel
100 _ 0001 printing.
1/19
PLEASE SELECT
THE PICTURE TO PRINT

SELECT PRINT

WB WB

RE RE
VIE W VIE W
SET SET

115
FZ10-PP.book 116 ページ ２００３年１１月１８日 火曜日 午後１時７分

Playback (advanced)
Preparation
• Connect the camera to a printer. (P112)
• Set the DPOF print with this camera in advance. (P91)
• Set the paper size and print quality. (Read the printer operating instructions.)

ª DPOF picture

1 Select [DPOF PICTURE]. 2 Select [YES] and print.

DIRECT PRINT DIRECT PRINT

PLS CHECK THE PRINTER
START PRINTING?
SINGLE DPOF
PICTURE PICTURE
YES NO
DATE DISPLAY
SELECT SET SELECT SET

WB WB WB WB

RE RE RE RE
VIE W VIE W VIE W VIE W
SET SET SET SET

• Press the [MENU] button, and you • Press the [DISPLAY] button to print
can change the DPOF print setting. the date.
(P91) • Press the [MENU] button to cancel
• When printing under the new printing.
settings, disconnect the USB
connection cable and connect it to ¬Suggestions/Tips ¬
the printer again. • When the total number of prints
becomes 255 or more, the number of
remaining pictures appears as [---] on
the screen.
• When you set the date print setting by
pressing the [DISPLAY] button, the
date is printed regardless of the date
print setting on DPOF setting. (P95)
• When the printer does not support the
date printing by DPOF setting, the
date may not be printed as it is on date
setting in DPOF setting.
• When you do not set the date print
setting, also check the date print
setting on the printer.

116
FZ10-PP.book 117 ページ ２００３年１１月１８日 火曜日 午後１時７分

Others
Others

Using the MC Protector/ND Filter

The MC protector (DMW-LMC72; optional) is a transparent filter which affects
neither the colors nor the amount of light, so it can always be used to protect the
camera’s lens.
The ND filter (DMW-LND72; optional) reduces the amount of light to approximately
1/8th (equal to adjusting the aperture value 3 increments) without affecting the color
balance.

1 Remove the lens cap and the lens 3 Attach the MC protector 1 or the
ring. ND filter 2.

2 Attach the lens hood.

• Cap 3 (supplied with MC

protector)

¬Suggestions/Tips ¬
• The lens cap supplied with the camera
cannot be attached to the MC
protector or the ND filter.
• You cannot attach the MC protector
and the ND filter at the same time.
• When taking pictures with the flash
using the MC protector/ND filter,
vignetting effect may occur.
• When the MC protector/ND filter fell,
they may be destroyed. Be careful not
to drop them when attaching.
• The cap supplied with MC protector
can also be used for the ND filter.
• MCu“Multi-coated”
NDu“Neutral Density”

117
FZ10-PP.book 118 ページ ２００３年１１月１８日 火曜日 午後１時７分

Others

After Use
After using the camera, it is recommended that you complete the following steps:

1 Turn the camera off and close the 3 Remove the lens hood (only when
flash. using it) and attach the lens ring
and the lens cap.

OFF ON

2 Remove the card and the battery.

(P15, 19)

• When removing the lens hood, hold

the whole of the lens hood gently
and then rotate it
counter-clockwise. (It may hard to
rotate the lens cap if you hold its
edge.)

¬Suggestions/Tips ¬
• If you will not be using the camera for
a long time,
– Remove the battery. (When you
insert the battery again, set the
clock.)
– Do not keep the camera in a place
where it will be subjected to high
temperatures, high humidity or soot.
Fungus may be attached to the lens
or condensation may occur.
– Keep the camera in a cool, dry and
well-ventilated place and avoid
storing near dust or chemicals.
– We recommend keeping it in a
closed case with the desiccant.

118
FZ10-PP.book 119 ページ ２００３年１１月１８日 火曜日 午後１時７分

Others

Screen Display
1 2 3 4 5 6 7 8
30 9
29 P ISO100 2304 10
_ 11
28 COOL 1 C AF 19
27 H 12
26 13
W T 24X 25 14
24 15
23 16
22 17
21 PROGRAM SHIFT
F2.8 1/25

20 19 18
ª In recording 21 Auto bracket (P42)
1 Recording mode
22 Program shift setting indication
2 Flash (P38) (P35)
3 Conversion lens (P86) 23 Spot AF area (P73)
4 White balance (P67)
24 Spot metering target (P73)
5 ISO sensitivity (P74) 25 Zoom/Digital zoom (P37, 77)
6 Picture size (P71) 26 Flash output adjustment/External
7 Quality (P72) flash (P40, 84)
8 Battery indication (P13) 27 Burst (P44)
9 Jitter alert indication (P33) 28 Optical image stabilizer (P80)
10 Frame/Time remain 29 Color effect (P78)
In Motion image mode: e.g. 11S 30 Continuous AF (P76)
11 Audio recording (P75)
• Current date and time appear for
12 Focus indication (P31)
about 5 seconds after turning the
13 Recording indication camera on or setting the clock. (P22)
14 Self-timer (P43)
15 Card access indication (P17)
16 AF area (P31)
17 Histogram (P29)
18 Aperture indication/Shutter speed
indication (P31)
19 Program shift indication (P35)
20 Exposure compensation (P41)
119
FZ10-PP.book 120 ページ ２００３年１１月１８日 火曜日 午後１時７分

Others

1 2 3 4 5 6 7

1 2304
14 100 _ 0001 8
13 PLAY AUDIO 1/19 9
10

P F2.8 1/25 ISO100 AUTO 11

10:00 DEC. 1.2003 12

ª In playback
1 Playback mode
2 DPOF (P91, 98)
1 (White):
DPOF setting for printing
1 (Green):
DPOF setting for Slide Show
1 (Green with number of prints):
DPOF setting for printing and
Slide Show
3 Protected picture (P96)
4 Picture with audio (P88)
5 Picture size (P71)
: In Motion image mode
6 Quality (P72)
: In Motion image mode
7 Battery indication (P13)
8 Folder/File number
9 Page number/Total pictures
10 Histogram (P29)
11 Recording information
12 Recorded date and time
13 Audio playback (P88)
PLAY MOTION
IMAGE : In Motion image mode
14 Flip animation (P81)

120
FZ10-PP.book 121 ページ ２００３年１１月１８日 火曜日 午後１時７分

Others

The Menu Items

ª [REC] mode menu

REC 1/4 SETUP REC 4/4 SETUP

1 W.BALANCE AUTO 13 FLIP ANIM.
2 AE AE MODE A 14 EXT.FLASH PRESET
3 PICT.SIZE 2304 15 CONVERSION OFF
4 QUALITY

SELECT SET EXIT MENU SELECT SET EXIT MENU

1 W.BALANCE (P67) 13 FLIP ANIM. (P81)

2 AE MODE (P52, 53, 54) 14 EXT.FLASH (P84)
3 PICT.SIZE (P71) 15 CONVERSION (P86)
4 QUALITY (P72)
REC SETUP 1/3
REC 2/4 SETUP 16 MONITOR
SPOT MODE 17 AUTO REVIEW OFF
5 OFF ON 18 BEEP
6 SENSITIVITY 100 19 POWER SAVE 2MIN.
7 AUDIO REC. OFF
8 C AF CONT.AF OFF SELECT SET EXIT MENU
SELECT SET EXIT MENU
16 MONITOR/FINDER (P25)
5 SPOT MODE (P73) • The screen (LCD monitor or
6 SENSITIVITY (P74) Viewfinder) you select appears as
7 AUDIO REC. (P75) a menu item.
8 CONT.AF (P76) 17 AUTO REVIEW (P25)
18 BEEP (P25)
3/4
19 POWER SAVE (P25)
REC SETUP
D.ZOOM
9 OFF ON REC SETUP 2/3
10 COL.EFFECT OFF MF ASSIST
20
11 PICT.ADJ. OFF ON
12 STABILIZER MODE1 21 NO.RESET
SELECT SET EXIT MENU 22 RESET
23 CLOCK SET
9 D.ZOOM (P77) SELECT SET EXIT MENU
10 COL.EFFECT (P78)
11 PICT.ADJ. (P79) 20 MF ASSIST (P26)
12 STABILIZER (P80) 21 NO.RESET (P26)
22 RESET (P26)
23 CLOCK SET (P22)

121
FZ10-PP.book 122 ページ ２００３年１１月１８日 火曜日 午後１時７分

Others

REC SETUP 3/3 PLAY SETUP 1/3

24 USB MODE MONITOR
25 LANGUAGE ENG 34 PLAY ON LCD OFF
35 VOLUME
BEEP

SELECT SET EXIT MENU SELECT SET EXIT MENU

24 USB MODE (P107) 34 PLAY ON LCD (P26)

25 LANGUAGE (P26) 35 VOLUME (P26)

ª [PLAY] mode menu

PLAY SETUP 2/3
• For items without numbers, refer to
POWER SAVE 2MIN.
those with the same name in [REC]
CLOCK SET
mode menu.
USB MODE Mass Storage
36 VIDEO OUT
PLAY 1/ 2 SETUP
26 ROTATE SELECT SET EXIT MENU
27 PROTECT
28 DPOF PRINT 36 VIDEO OUT (P26, 106)
29 SLIDE SHOW
30 AUDIO DUB.
SELECT SET EXIT MENU

26 ROTATE (P90)
27 PROTECT (P96)
28 DPOF PRINT (P91)
29 SLIDE SHOW (P98)
30 AUDIO DUB. (P100)

PLAY 2/ 2 SETUP
31 RESIZE
32 TRIMMING
33 FORMAT

SELECT SET EXIT MENU

31 RESIZE (P101)
32 TRIMMING (P103)
33 FORMAT (P105)

122
FZ10-PP.book 123 ページ ２００３年１１月１８日 火曜日 午後１時７分

Others

Cautions for Use

ª Optimal Use of the Camera When you use the camera on a rainy
Keep the camera away from or snowy day or on a beach or similar
place, do not let grit, fine dust or
magnetized equipment (such as a
microwave oven, TV, video game seawater get into the camera.
equipment, etc.). • Grit or dust may damage the camera
or card. (Care should be taken when
• If you use the camera on or near a TV,
pictures and sounds may be disturbed inserting and removing the card.)
due to electromagnetic wave radiation. • If seawater splashes onto the camera,
wet a soft cloth with tap water, wring it
• Do not use the camera near a cell
phone because doing so may cause well, and use it to wipe the camera
noise to adversely affect the pictures body carefully. Then, wipe it again
thoroughly with a soft, dry cloth.
and sounds.
• Recorded data may be damaged, or When carrying this camera, take care
pictures may be distorted by strong not to drop or hit it.
magnetic fields created by speakers or • The outer case may be destroyed by
large motors. the strong shock, and it may cause
• Electromagnetic wave radiation malfunction of this camera.
generated by a microprocessor may • For storing or transporting the camera,
adversely affect the camera, causing place it in a bag or case lined with soft
the disturbance of pictures and pads to prevent the coating on the
sounds. camera body from being worn.
• If the camera is affected by
Do not use benzine, thinner or
magnetically charged equipment and
alcohol for cleaning the camera.
does not function properly, turn the
• Before cleaning the camera, remove
camera off and remove the battery or
the battery or disconnect the AC
disconnect AC adaptor and then insert
adaptor from the electrical outlet.
the battery or connect AC adaptor
• The camera body may be deformed
again. Thereafter, turn the camera on.
and the surface finish may peel off.
Do not use the camera near radio • Wipe the camera with a soft, dry cloth.
transmitters or high-voltage lines. To remove stubborn stains, wipe with a
• If you record near radio transmitters or cloth that is soaked in a detergent
high-voltage lines, recorded pictures diluted with water and afterward finish
or sounds may be adversely affected. wiping with a dry cloth.
Do not spray insecticides or volatile
chemicals onto the camera.
• If the camera is sprayed with such
chemicals, the camera body may be
damaged and the surface finish may
peel off.
• Do not keep rubber or plastic products
in contact with the camera for a long
period of time.

123
FZ10-PP.book 124 ページ ２００３年１１月１８日 火曜日 午後１時７分

Others
ª Condensation Dispose of an unusable battery.
When using the camera outdoors during • The battery has a limited life.
• Do not throw the battery into fire
very cold weather, condensation can
form on the camera and lens when you because it may cause an explosion.
return to a warm place. • An unusable battery should be
discarded in accordance with battery
When condensation has taken place: recycling laws.
Turn the camera off and leave the For information you can call the RBRC
camera in this condition for about hotline at 1-800-822-8837.
2 hours. When the camera becomes
close to the ambient temperature, the ª Cautions for Storage
condensation disappears naturally.
Before storing the camera, remove the
ª Optimal Use of the Battery card and the battery.
Store all the components in a dry place
The battery is a rechargeable lithium ion with a relatively stable temperature.
battery. Its ability to generate power is (Recommended temperature:
based upon the chemical reaction that 59oF to 77oF (15oC to 25oC),
takes place inside it. This reaction is Recommended humidity: 40% to 60%)
susceptible to the surrounding
Battery
temperature and humidity, and, if the
temperature is too high or too low, the • Do not leave the camera and the
operating time of the battery will be battery at the place where the
temperature is too high, such as inside
shorter.
a car during the summer.
If you drop the battery accidentally, • Extremely high or low temperatures
check to see if the battery body and will shorten the life of the battery.
terminals are deformed. • If the battery is kept in smoky or dusty
Inserting a deformed battery to the places, the terminals may rust and
camera may damage the camera. cause malfunctions.
Be sure to remove the battery after • Do not allow the battery terminals to
use. come in contact with metal objects
If it is left inserted to the camera, a (such as necklaces, hairpins, etc.).
minute amount of current is consumed This can result in a short circuit or heat
even when the camera is turned off. If generation and, if you touch the
the battery is left inserted in the camera battery in this condition, you may be
for a long time, discharge takes place. badly burned.
The battery may become unusable even • Store the battery in a completely
after it is charged. discharged state. To store the battery
for a long period of time, we
recommend charging it once every
year and storing it again after you
completely use up the charged
capacity.

124
FZ10-PP.book 125 ページ ２００３年１１月１８日 火曜日 午後１時７分

Others
Card ª Folder Composition
• Do not leave the card in places where
When a Memory Card with data
there is high temperature or direct
recorded on it is inserted into a PC, the
sunlight, or where electromagnetic
folders shown below will appear.
waves or static electricity are easily
generated. SD Memory DCIM
• Do not bend or drop the card. The Card 100_PANA
card or the recorded content may be EXPORT
damaged.
MISC
• After use, be sure to remove the card
from the camera. PRIVATE1
• Do not touch the terminals on the back • In the [100_PANA] folder it is possible
of the card with your fingers. Do not to record up to 999 pictures.
allow dirt, dust or water to enter it. • In the [MISC] folder it is possible to
AC adaptor record the files that have been set with
• If you use the AC adaptor near a radio, DPOF settings.
radio reception may be disturbed. • The files recorded in flip animation
Keep the AC adaptor 3.28 feet (1 m) function are stored in [PRIVATE1]
or more away from radio. folder.
• When the AC adaptor is in use, it may • The motion images created by flip
generate whirring sounds. However, animation function are store in
this is not a malfunction. [100_PANA] or other folder.
• After use, be sure to disconnect the
AC cable. (If it is left connected, a ª Printing pictures recorded with
minute amount of current is HDTV mode
consumed.)
• Keep the terminal of the AC adaptor When you print pictures recorded by
and battery clean. setting the picture size to [HDTV]
(1920k1080 pixels), both ends of the
ª Screen pictures may be cut out.
LCD monitor To print pictures with ends:
• In a place with drastic temperature When you order photo studios to print
changes, condensation may form on
pictures:
the LCD monitor. Wipe it with a soft,
• Ask the photo studio if the pictures can
dry cloth.
be printed with both ends.
• If the camera is extremely cold when
you turn the camera on, the image on When you print pictures with your
the LCD monitor is slightly darker than printer:
usual at first. However, as the internal • When using the printer with a trimming
temperature increases, it goes back to feature or a feature which cuts out
the normal brightness. both edges of the pictures, cancel the
Viewfinder feature for printing.
• Do not direct the Viewfinder or lens to • The feature depends on the printer
the sun. Internal components may be used. Refer to the operating
seriously damaged. instructions of the printer for details.

125
FZ10-PP.book 126 ページ ２００３年１１月１８日 火曜日 午後１時７分

Others

Approximate number of recordable pictures

and the size

Picture 2304k1728 1600k1200 1280k960 640k480

size
Quality
16 MB 8 16 17 34 22 43 69 129
32 MB 17 34 36 72 47 90 145 270
64 MB 35 70 74 149 96 184 298 553
128 MB 72 142 150 301 195 372 602 1118
256 MB 144 283 300 600 390 743 1200 2229
512 MB 291 571 604 1209 785 1497 2418 4491

Picture 1920k1080
size (HDTV)
Quality
16 MB 17 34
32 MB 36 72
64 MB 74 149
128 MB 150 301
256 MB 300 600
512 MB 604 1209

• If you mix fine quality and standard quality, the number of recordable pictures
changes.

126
FZ10-PP.book 127 ページ ２００３年１１月１８日 火曜日 午後１時７分

Others

Message Display
[NO MEMORY CARD] [CAN’T BE SET ON THIS PICTURE] /
Insert the card. [CAN’T BE SET ON SOME
PICTURES]
[THIS MEMORY CARD IS If the pictures are not based on the DCF
PROTECTED] standard, the DPOF print cannot be set.
Cancel the card lock.
[NO ADDITIONAL DELETE
[NO VALID IMAGE TO PLAY] SELECTIONS CAN BE MADE]
Play back after recording or after You have exceeded the number of
inserting the card with a recorded pictures that can be set at once with
picture. multi-delete setting.

[MEMORY CARD FULL] / [MEMORY CARD ERROR

[NOT ENOUGH MEMORY IN THE FORMAT THIS CARD?]
CARD] The format of the card cannot be
Insert a new card or delete the recognized by this camera. Format the
unnecessary data. card again with this camera.

[PLEASE CLOSE THE FLASH] [SYSTEM ERROR]

Be sure to close the flash after use. This message appears when the
camera does not operate properly. Turn
[MODE DIAL IS NOT IN THE PROPER the camera off and on. If the message
POSITION] persists, contact the dealer or your
This message appears when you turn nearest servicenter.
the camera on with the mode dial in the
wrong position. [MEMORY CARD ERROR]
Rotate the mode dial to the proper Failed access to the card.
position. Insert the card again.

[PLEASE SET THE CLOCK] [READ ERROR]

This message appears when you use Data reading error.
the camera for the first time or you do Play it back again.
not use the camera for a long time.
Set the clock. [WRITE ERROR]
Data writing error.
[THIS PICTURE IS PROTECTED] Turn the camera off and remove the
After cancelling the protect setting, you card. Then insert the card and turn the
can delete or overwrite the picture. camera on again. Be sure that the
camera is turned off before removing or
[THIS PICTURE CAN’T BE inserting the card to avoid damage.
DELETED] / [SOME PICTURES CAN’T
BE DELETED]
The pictures not based on the DCF
standard cannot be deleted.

127
FZ10-PP.book 128 ページ ２００３年１１月１８日 火曜日 午後１時７分

Others

Troubleshooting
1: The camera is not turned on. 6: The screen is too bright or dark.
1-1: Are the battery inserted or the AC 6: Adjust the brightness of the
adaptor correctly connected? screen.
Check the connection.
1-2: Is the battery sufficiently charged? 7: Flash is not activated.
Use the battery that has been 7: Is the flash closed?
sufficiently charged. Press the [ OPEN] button to
open the flash.
2: As the camera is turned on, it
turns off immediately. 8: Unreadable language was
2: Is the battery charge insufficient to selected by mistake.
operate the camera? 8: Select [ ] icon on the [SETUP]
Use the battery with charged one. menu to set the desired language.

3: The brightness of the screen 9: The subject is not focused

changes dark or bright for a properly.
moment. 9-1: Is the subject out of the focus
3: This phenomenon appears when range?
pressing the shutter button 9-2: When you cannot focus on the
halfway to set the aperture value subject even if you tried many
and does not affect the recorded times, once turn the camera off
pictures. and turn it on again.

4: The picture cannot be recorded. 10: The picture is not played back.
4-1: Is the card inserted? 10-1: Is the card inserted?
4-2: Is the mode dial correctly set? 10-2: Is there a picture in the card?
Check it. 10-3: Is the mode dial set to playback
4-3: There is no memory capacity left [ ]?
on the card. Before recording,
delete some pictures.

5: The picture is not displayed on

the LCD monitor.
5: Does the picture appear on the
Viewfinder?
Press the [EVF/LCD] button to
switch to LCD monitor display.

128
FZ10-PP.book 129 ページ ２００３年１１月１８日 火曜日 午後１時７分

Others
11: The picture does not appear on
the television.
11-1: Is the camera connected to the TV
correctly?
Check it.
11-2: Set the TV to video input mode.

12: When connecting to a PC,

pictures cannot be transferred.
12-1: Is the camera connected to the PC
correctly?
Check it.
12-2: Is the camera recognized by the
PC correctly?
12-3: Is the USB mode set correctly?

13: The clock setting is reset.

13-1: If you do not use the camera for a
long time, the clock setting may be
reset. When the message
[PLEASE SET THE CLOCK]
appears, set the clock again.
13-2: When you take a picture before
setting the clock, [0:00 0. 0. 0] is
recorded.

14: The camera will make sounds

caused by internal mechanical
movement when it is shaken.
14: The sound arises when the lens
moves. This is not a malfunction.

15: Some pixels are inactive or

always lit on the LCD monitor.
15: This is not a malfunction. These
pixels do not affect the recorded
pictures.

16: The pictures cannot be printed

with printers supporting USB
Direct-Print or PictBridge.
16: Is the USB mode set correctly?

129
FZ10-PP.book 130 ページ ２００３年１１月１８日 火曜日 午後１時７分

Others

Specifications
Digital Camera Information for your safety

Power Source: DC 8.4 V

Power Consumption: 2.6 W (When recording with LCD Monitor)
2.4 W (When recording with Viewfinder)
1.7 W (When playing back with LCD Monitor)
1.5 W (When playing back with Viewfinder)

Camera Effective pixels 4,000,000 pixels

Image sensor 1/2.5q CCD, total pixel number 4,230,000 pixels
Primary color filter
Lens Optical 12k zoom, fl6.0 – 72.0 mm (35 mm film camera
equivalent: 35 – 420 mm)/F2.8
Digital zoom Single: 3k, Burst: 3k
Focus TTL Auto/Macro/Manual/Spot AF (Spot mode)
Focus range 0.98 feet (30 cm) (Wide)/6.56 feet (2 m) (Tele) – ¶,
Macro/Aperture-priority AE/Shutter-priority AE/
Manual exposure: 0.16 feet (5 cm) (Wide)/
6.56 feet (2 m) (Tele) – ¶
Shutter system Electronic shutteriMechanical shutter
Burst recording 4 frames/second (high speed), 2 frames/second (low
speed), max. 7 frames (standard)/max. 5 frames (fine)
(Performance is only with SD Memory Card.
MultiMediaCard performance will be less.)
Motion image recording 320k240 pixels
(30 or 10 frames/second with audio. The maximum
recording time depends on the capacity of the card.)
ISO sensitivity AUTO (without flash: from ISO50 to 200/
with flash: from ISO50 to 400)/50/100/200/400
Shutter speed 8 – 1/2,000th
Motion image mode: 1/30th – 1/2,000th
White balance AUTO/Daylight/Cloudy/Halogen/Flash/White set
Exposure (AE) Program AE (P)/Aperture-priority AE (A)/
Shutter-priority AE (S)/Manual exposure (M)
Exposure compensation (1/3 EV Step, j2 – i2 EV)
Metering mode Multi/Spot (Spot mode)
LCD monitor 2.0q low-temperature polycrystalline TFT LCD
(130,000 pixels) (field of view ratio about 100%)
Viewfinder Color electrical Viewfinder (114,000 pixels)
(field of view ratio about 100%)
(with dioptor adjustment j4 – i4 dioptor)
Flash Built-in pop up flash
Flash range: (ISO AUTO)
Approx. 1.31 feet (40 cm) – 13.1 feet (4 m) (Wide)/
Approx. 6.56 feet (2 m) – 13.1 feet (4 m) (Tele)
AUTO, AUTO/Red-eye reduction, Forced ON,
Slow sync./Red-eye reduction, Forced OFF
Microphone Monaural
Speaker Monaural
130
FZ10-PP.book 131 ページ ２００３年１１月１８日 火曜日 午後１時７分

Others
Recording media SD Memory Card/MultiMediaCard
Picture size 2304k1728 pixels, 1600k1200 pixels,
1280k960 pixels, 640k480 pixels, 1920k1080 pixels
(Still picture)
320k240 pixels (Motion image)
Quality Fine/Standard
Recording file format
Still Picture JPEG (Design rule for Camera File system, based on
Exif 2.2 standard), DPOF corresponding
Picture with audio JPEG (Design rule for Camera File system, based on
Exif 2.2 standard)i640k480 pixels
QuickTime (picture with audio)
Motion images QuickTime Motion JPEG (motion images with audio)
Interface
Digital USB 1.1
Analog video/audio NTSC/PAL Composite/Audio line output (monaural)
Terminal
USB 5 pin Mini USB
Analog video/audio φ 2.5 mm jack
DC IN type 3 jack
Dimensions (WkHkD) 5 7/16qk3 7/16qk4 5/32q (138.5k87.2k105.7 mm)
(excluding the projection part)
Weight Approx. 18.3 oz/518 g
(excluding Memory Card and battery)
Approx. 19.4 oz/550 g (with Memory Card and battery)
Operating Temperature 32oF – 104oF (0oC – 40oC)
Operating Humidity 10% – 80%

Battery Charger/AC Adaptor

(Panasonic DE-928A) Information for your safety

Input 110 – 240 V 50/60 Hz, 0.29 A

Output DIGITAL CAMERA 8.4 V 1.2 A
CHARGE 8.4 V 0.65 A

Battery Pack (lithium-ion)

(Panasonic CGA-S002A) Information for your safety

Voltage/capacity 7.2 V, 680 mAh

131
FZ10-PP.book 132 ページ ２００３年１１月１８日 火曜日 午後１時７分

Others
Others

Digital Camera Accessory System

Accessory# Figure Description

CGA-S002A Lithium Ion Battery

DMW-FL28 External Flash*1

DMW-LTZ10 Tele Conversion Lens

DMW-LWZ10 Wide Conversion Lens

DMW-LND72 ND Filter

DMW-LMC72 MC Protector

RP-SDH512U1A 512 MB SD Memory Card

RP-SDH256U1A 256 MB SD Memory Card
RP-SDH128U1A 128 MB SD Memory Card
RP-SD064BPPA 64 MB SD Memory Card
RP-SD032BPPA 32 MB SD Memory Card
SD USB Reader/Writer
BN-SDCAPU/1B (compatible with
MultiMediaCard)
SD PC Card Adaptor
BN-SDABPU/1B (compatible with
MultiMediaCard)

*1 Slave function equipped with DMW-FL28 can not be used with

DMC-FZ10’s built-in flash.
* Please refer to page 13, for details on the battery charging time and
available recording time.
* NOTE: Accessories and/or model numbers may vary by country. Please
consult your local dealer.

132
FZ10-PP.book 133 ページ ２００３年１１月１８日 火曜日 午後１時７分

Others

Digital Camera Accessory Order Form

(For USA Customers)

Please photocopy this form when placing an order.

1. Digital Camera Model #
2. Items Ordered
Accessory # Description Price Each Quantity Total Price

Subtotal
Your State & Local Sales Tax
Shipping & Handling 6.95
Total Enclosed
3. Method of payment (check one)
Check of Money Order enclosed (NO C.O.D.SHIPMENTS)
VISA Credit Card #
MasterCard Expiration Date
Discover Customer Signature
Make Check or Money Order to: PANASONIC ACCESSORIES
(Please do not send cash)
4. Shipping information (UPS delivery requires complete street address)
Ship To:
Mr.
Mrs.
Ms.
First Last Phone#:
Day ( )
Street Address
Night ( )
City State Zip

TO OBTAIN ANY OF OUR DIGITAL CAMERA ACCESSORIES YOU CAN DO ANY OF

THE FOLLOWING:
VISIT YOUR LOCAL PANASONIC DEALER
OR
CALL PANASONIC’S ACCESSORY ORDER LINE AT 1-800-332-5368
[6 AM-5 PM M-F, 6 AM-10:30 AM SAT, PACIFIC TIME]
OR
MAIL THIS ORDER TO: PANASONIC SERVICES COMPANY ACCESSORY ORDER OFFICE
20421 84th Avenue South Kent, WA. 98032

In CANADA, please contact your local Dealer for more information on

Accessories.
133
FZ10-PP.book 134 ページ ２００３年１１月１８日 火曜日 午後１時７分

Others

Request for Service Notice (For USA Only)

Please photocopy this form when making a request for service notice.
In the unlikely event this product needs service.

Request for Service Notice: • Please include your proof of purchase.

(Failure to do so will delay your repair.)
(USA Only) • To further speed your repair, please provide
an explanation of what wrong with the unit
and any symptom it is exhibiting.

Mail this completed form and your Proof of Purchase along with your unit to:
Panasonic Services Company
1705 N. Randall Road
Elgin, IL. 60123-7847
Attn: Digital Camera Repair

134
FZ10-PP.book 135 ページ ２００３年１１月１８日 火曜日 午後１時７分

Others

Limited Warranty (For USA Only)

PANASONIC CONSUMER PANASONIC SALES COMPANY,
ELECTRONICS COMPANY, DIVISION OF MATSUSHITA
DIVISION OF MATSUSHITA ELECTRIC OF PUERTO RICO,
ELECTRIC CORPORATION OF INC.
AMERICA, One Panasonic Way Ave. 65 de Infanteria, Km. 9.5, San
Secaucus, New Jersey 07094 Gabriel Industrial Park, Carolina,
Puerto Rico 00985

Panasonic Digital Still Camera

Limited Warranty
Limited Warranty Coverage
If your product does not work properly because of a defect in materials or
workmanship, Panasonic Consumer Electronics Company or Panasonic
Sales Company (collectively referred to as “the warrantor”) will, for the
length of the period indicated on the chart below, which starts with the date
of original purchase (“warranty period”), at its option either (a) repair your
product with new or refurbished parts, or (b) replace it with a new or
refurbished product. The decision to repair or replace will be made by the
warrantor.

PRODUCT OR PART NAME PARTS LABOR

DIGITAL STILL CAMERA
(EXCEPT ITEMS LISTED 1 (ONE) YEAR 90 (NINETY) DAYS
BELOW)
CCD 6 (SIX) MONTHS 90 (NINETY) DAYS
RECHARGEABLE BATTERY
PACK (IN EXCHANGE FOR 90 (NINETY) DAYS NOT APPLICABLE
DEFECTIVE BATTERY PACK)
SD MEMORY CARD
(IN EXCHANGE FOR 90 (NINETY) DAYS NOT APPLICABLE
DEFECTIVE SD CARD)
During the “Labor” warranty period there will be no charge for labor. During
the “Parts” warranty period, there will be no charge for parts. You must
carry-in or mail-in your product during the warranty period. If non-
rechargeable batteries are included, they are not warranted. This warranty
only applies to products purchased and serviced in the United States or
Puerto Rico. This warranty is extended only to the original purchaser of a
new product which was not sold “as is”. A purchase receipt or other proof
of the original purchase date is required for warranty service.
135
FZ10-PP.book 136 ページ ２００３年１１月１８日 火曜日 午後１時７分

Others
Carry-In or Mail-In Service
For Carry-In or Mail-In Service in the United States call
1-800-272-7033.
For assistance in Puerto Rico call Panasonic Sales Company
(787)-750-4300 or fax (787)-768-2910.

This warranty ONLY COVERS failures due to defects in materials or

workmanship, and DOES NOT COVER normal wear and tear or
cosmetic damage. The warranty ALSO DOES NOT COVER damages
which occurred in shipment, or failures which are caused by products
not supplied by the warrantor, or failures which result from accidents,
misuse, abuse, neglect, mishandling, misapplication, alteration, faulty
installation, set-up adjustments, misadjustment of consumer controls,
improper maintenance, power line surge, lightning damage,
modification, or commercial use (such as in a hotel, office, restaurant, or
other business), rental use of the product, service by anyone other than
a Factory Servicenter or other Authorized Servicer, or damage that is
attributable to acts of God.

THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED

UNDER “LIMITED WARRANTY COVERAGE”. THE WARRANTOR IS
NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES
RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT
OF ANY BREACH OF THIS WARRANTY. (As examples, this excludes
damages for lost time, travel to and from the servicer, loss of media or
images, data or other memory content. The items listed are not
exclusive, but are for illustration only.) ALL EXPRESS AND IMPLIED
WARRANTIES, INCLUDING THE WARRANTY OF
MERCHANTABILITY, ARE LIMITED TO THE PERIOD OF THE
LIMITED WARRANTY.

Some states do not allow the exclusion or limitation of incidental or

consequential damages, or limitations on how long an implied warranty
lasts, so the exclusions may not apply to you.
This warranty gives you specific legal rights and you may also have other
rights which vary from state to state. If a problem with this product
develops during or after the warranty period, you may contact your
dealer or Servicenter. If the problem is not handled to your satisfaction,
then write to the warrantor’s Consumer Affairs Department at the
addresses listed for the warrantor.

PARTS AND SERVICE WHICH ARE NOT COVERED BY THIS LIMITED

WARRANTY ARE YOUR RESPONSIBILITY.
136
FZ10-PP.book 137 ページ ２００３年１１月１８日 火曜日 午後１時７分

Others

Customer Services Directory (For USA Only)

For Product Information, Operating Assistance, Literature Request, Dealer Locations, and
all Customer Service inquiries please contact:
1-800-272-7033, Monday-Friday 8:30am-8pm EST.

Web Site: http://www.panasonic.com/support

You can purchase parts, accessories or locate your
nearest servicenter by visiting our Web Site.

Accessory Purchases:
Purchase Parts, Accessories and Instruction Books online for all Panasonic Products by
visiting our Web Site at:
http://www.pasc.panasonic.com
or, send your request by E-mail to:
npcparts@panasonic.com
You may also contact us directly at:
1-800-332-5368 (Customer Orders Only)
Panasonic Services Company 20421 84th Avenue South, Kent, WA 98032
(6 am to 5 pm Monday - Friday; 6 am to 10:30 am Saturday; PST)
(Visa, MasterCard, Discover Card, American Express, Check)

Product Repairs
Centralized Factory Servicenter
Panasonic Services Company
MAIL TO : 1705 N. Randall Road,
Elgin, IL 60123-7847
Attention: Digital Camera Repair

Please carefully pack and ship, prepaid and insured, to the Elgin Centralized Factory
Servicenter.
Customer's in Puerto Rico, please ship or carry in to location below (“Service in Puerto Rico”).

Service in Puerto Rico

Matsushita Electric of Puerto Rico, Inc. Panasonic Sales Company/ Factory Servicenter:
Ave. 65 de Infanteria, Km. 9.5, San Gabriel Industrial Park, Carolina, Puerto Rico 00985
Phone (787) 750-4300 Fax (787) 768-2910
As of November 2003

137
FZ10-PP.book 138 ページ ２００３年１１月１８日 火曜日 午後１時７分

Others
Others

Index
A I
AC Adaptor .................................... 16 ISO Sensitivity ............................... 74
Adjusting Flash Output ................ 40 J
AF/AE Lock .................................... 34 Jitter ................................................. 33
Aperture-priority AE ................ 52, 56 L
Audio Dubbing ............................. 100 Language setting .......................... 26
Auto Bracket .................................. 42 LCD Monitor ................... 27, 119, 125
Auto Review ................................... 25 Lens Cap ........................................ 21
B Lens Hood ...................................... 21
Brightness of the LCD M
Monitor/Viewfinder .................... 25 Macro Mode ................................... 57
Built-in Flash .................................. 38 Manual Exposure .......................... 54
Burst Mode ..................................... 44 Manual Exposure Assistance ..... 55
C Manual Focus ................................ 65
Card ................................................ 17 Mass Storage ...................... 107, 109
Card Access Indication ................ 17 MC Protector ................................ 117
Clock Set .................................. 22, 26 MF ASSIST .............................. 26, 65
Color Effect .................................... 78 Monitor Priority ........................ 26, 28
Condensation .............................. 124 Motion Images ............................... 63
Continuous AF .............................. 76 Multi Playback ............................... 46
Conversion Lens ........................... 86 N
Creating Motion Images .............. 82 ND Filter ....................................... 117
D Night Portrait Mode ....................... 62
Date Printing .................................. 95 NO.RESET ..................................... 26
Deleting Pictures ............... 48, 49, 50 NTSC .............................................. 26
Digital Zoom ................................... 77 O
DPOF Print Setting ....................... 91 One Shot AF .................................. 66
E Operational sound ........................ 25
Exposure ........................................ 33 Optical Image Stabilizer ............... 80
EXPOSURE Button ................ 35, 51 Optical Zoom ................................. 37
Exposure Compensation ............. 41
External Flash ............................... 84
F
Flip Animation ................................ 81
Focus .............................................. 32
Formatting .................................... 105
H
HDTV .............................. 71, 106, 125
Histogram ....................................... 29

138
FZ10-PP.book 139 ページ ２００３年１１月１８日 火曜日 午後１時７分

Others

P V
PAL .................................................. 26 Video output ................................... 26
Panning Mode ............................... 60 Viewfinder ...................... 27, 119, 125
PictBridge ............................. 112, 113 Volume of Speakers ..................... 26
Picture Size .................................... 71 W
Pictures with Audio ....................... 75 White Balance ............................... 67
Playback ......................................... 45
Playback Pictures on TV ........... 106
Playback Zoom ............................. 47
Playing Back Motion Images ...... 89
Playing Back Pictures with
Audio ........................................... 88
Portrait Mode ................................. 58
Power Indicator ............................. 32
Power Save ................................... 25
Prefocus ......................................... 66
Program AE ................................... 31
Program Shift ................................ 35
Protect ............................................ 96
PTP ....................................... 107, 110
Q
Quality ............................................. 72
R
Recording Guide Line .................. 28
Reset of setting ............................. 26
Resizing ........................................ 101
Review ............................................ 36
Rotate ............................................. 90
S
Self-timer ........................................ 43
Setup Menu ............................. 25, 26
Shutter-priority AE .................. 53, 56
Slide Show ..................................... 98
Sports Mode .................................. 59
Spot Mode ...................................... 73
Strap ................................................ 20
T
Trimming ...................................... 103
U
USB Connection Cable .............. 107
USB Direct-Print .................. 112, 115
USB Mode ...................................... 26

139
FZ10-PP.book 140 ページ ２００３年１１月１８日 火曜日 午後１時７分

Others
Others

Spanish Quick Use Guide/Guía española de

uso rápido
• Cargue la batería antes del uso.
• Prepare la cámara, el cable de CA, la batería, el adaptador de CA y la tarjeta.
• Verifique que la cámara esté apagada y que el objetivo esté retraído.
• Cierre el flash.

ª Preparaciones

1 Cargue la batería. 3 1 Inserte la tarjeta.

2 Cierre la tapa de la tarjeta/
batería.

• La batería no puede ser cargada

cuando está conectado el cable
CC al adaptador CA.
2 1 Haga deslizar la palanca para
abrir la tapa de la tarjeta/
batería.
2 Inserte la batería.

MEMORY CARD/
BATTERY

OPEN

140
FZ10-PP.book 141 ページ ２００３年１１月１８日 火曜日 午後１時７分

Others
ª Grabación ª Reproducción
• Quite la tapa del objetivo.
• Tenga cuidado de no perder la tapa
6 1 Seleccione el modo de
reproducción [ ].
del objetivo.
2 Seleccione la imagen que
4 1 Encienda la cámara. quiere ver.
2 Ajuste el reloj.

A/S/M
3 Seleccione el modo AE [ ] P
del programa.

A/S
/M
P

WB

OFF ON
RE
VIE W
SET

5 1 Obra el flash.
(Cuando usa el flash)
2 Saque una imagen.

OPEN

141
FZ10-PP.book 142 ページ ２００３年１１月１８日 火曜日 午後１時７分

MEMO

142
FZ10-PP.book 143 ページ ２００３年１１月１８日 火曜日 午後１時７分

MEMO

143
FZ10-PP.book 144 ページ ２００３年１１月１８日 火曜日 午後１時７分

Panasonic Consumer Electronics Company,

Division of Matsushita Electric Corporation of America
One Panasonic Way, Secaucus, NJ 07094

Panasonic Sales Company ("PSC")

Division of Matsushita Electric of Puerto Rico, Inc.
Ave. 65 de Infanteria, Km. 9.5, San Gabriel Industrial Park, Carolina, Puerto Rico 00985

Panasonic Canada Inc.

5770 Ambler Drive, Mississauga, Ontario, L4W 2T3
C 2003 Matsushita Electric Industrial Co., Ltd.

P
VQT0F85-2
F1103Ua2113(06000C)
C