Honeywell 60 Series IP Cameras

Configuration Guide
HC60W35R2 HC60W45R2 HC60WB5R2 HC60WZ2E30
HC60W35R4 HC60W45R4 HC60WB5R5

Recommended Find the latest version of this and other Honeywell 60 Series IP
camera documents on the Honeywell Video website. Go to:
http://www.honeywellvideosystems.com/ndaa/ to find your
camera and view/download the latest documentation.

Refer to the Honeywell Open Technology Alliance to learn more

about our open and integrated solutions (go to:
http://www.security.honeywell.com/hota/).
Revisions

Issue Date Revisions

A 03/2020 New document.

i
 Cautions and Warnings

WARNING Installation and servicing should be performed only by qualified

and experienced technicians to conform to all local codes and to maintain your
warranty.

WARNING To ensure compliance with electrical safety standards, CSA

Certified/UL Listed LPS or Class 2 power adapters are required. Power over
Ethernet (PoE) shall be provided by listed Information Technology Equipment
meeting the IEEE 802.3af PoE standard. The PoE is not intended to be connected
to exposed (outside plant) networks.
The Ethernet connection is not intended to be connected to exposed (outside
plant) networks. Do not connect two power sources to the camera at the same time.

WARNING To comply with EN50130-4 requirements, a UPS should be

employed when powering the camera from 24 V AC.

Caution Invisible LED radiation (850 nm). Avoid exposure to beam.

Regulatory Statements
Photo biological safety
This product fulfills the requirements for photo biological safety according to IEC/EN 62471
(risk group 1).

General Data Protection Regulation

Please be aware that this product can store personal data.
Personal data is protected by the General Data Protection Regulation (2016/679) in Europe
and therefore the owners of personal data have obtained certain rights thanks to this
regulation.

ii
We strongly advise you to be fully aware of these owner (“data subjects”) rights as well as
which limitations you have to obey regarding the use and distribution of this data.
Further details can be found on the GDPR website of the EU:
https://ec.europa.eu/commission/priorities/justice-and-fundamental-rights/data-
protection/2018-reform-eu-data-protection-rules_en

FCC Compliance Statement (For IPC Model)

Information to the User: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party

Note responsible for compliance could void the user’s authority to
operate the equipment.

This Class B digital apparatus complies with Canadian ICES-003.

FCC Compliance Statement (For PTZ Model)

This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense. Changes
or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
This Class A digital apparatus complies with Canadian ICES-003.

iii
 Manufacturer’s Declaration of Conformance
North America
The equipment supplied with this guide conforms to UL 62368-1 and CSA C22.2
No. 62368-1.
Europe
The manufacturer declares that the equipment supplied with this guide is compliant with the
European Parliament and Council Directive on the Restrictions of the use of certain
hazardous substances in electrical and electronic equipment (2015/863/EU), General
Product Safety Directive (2001/95/EC), and the essential requirements of the EMC Directive
(2014/30/EU), conforming to the requirements of standards EN 55032 for emissions, EN
50130-4 for immunity, and EN 62368-1 for electrical equipment safety.

Waste Electrical and Electronic Equipment (WEEE)

Correct Disposal of this Product (applicable in the European Union and other
European countries with separate collection systems).
This product should be disposed of, at the end of its useful life, as per
applicable local laws, regulations, and procedures.

Safety Instructions
Before installing or operating the unit, read and follow all instructions. After installation,
retain the safety and operating instructions for future reference.
1. HEED WARNINGS - Adhere to all warnings on the unit and in the operating instructions.
2. INSTALLATION
• Install in accordance with the manufacturer’s instructions.
• Installation and servicing should be performed only by qualified and experienced
technicians to conform to all local codes and to maintain your warranty.
• Any wall or ceiling mounting of the product should follow the manufacturer’s
instructions and use a mounting kit approved or recommended by the manufacturer.
3. POWER SOURCES - This product should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type of power supplied to your
facility, consult your product dealer or local power company.
4. MOUNTING SYSTEM - Use only with a mounting system recommended by the
manufacturer, or sold with the product.
5. ATTACHMENTS/ACCESSORIES - Do not use attachments/accessories not
recommended by the product manufacturer as they may result in the risk of fire, electric
shock, or injury to persons.
6. CLEANING - Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.

iv
7. SERVICING - Do not attempt to service this unit yourself. Refer all servicing to qualified
service personnel.
8. REPLACEMENT PARTS - When replacement parts are required, be sure the service
technician has used replacement parts specified by the manufacturer or have the same
characteristics as the original part. Unauthorized substitutions may result in fire, electric
shock or other hazards. Using replacement parts or accessories other than the original
manufacturers may invalidate the warranty.

Warranty and Service

Subject to the terms and conditions listed on the product warranty, during the warranty period
Honeywell will repair or replace, at its sole option, free of charge, any defective products
returned prepaid.
In the event you have a problem with any Honeywell product, please call Customer Service at
1.800.323.4576 for assistance or to request a Return Merchandise Authorization (RMA)
number.
Be sure to have the model number, serial number, and the nature of the problem available for
the technical service representative.
Prior authorization must be obtained for all returns, exchanges, or credits. Items shipped to
Honeywell without a clearly identified Return Merchandise Authorization (RMA) number
may be refused.

v
Table of Contents
1 Introduction ....................................................................................................................................................... 1
Overview ................................................................................................................................................................................ 1
Key Features ........................................................................................................................................................................ 1
2 Accessing the Camera ..................................................................................................................................... 3
Installing the Unified Tool ............................................................................................................................................. 3
Discovering Your Camera on the Network ............................................................................................................. 5
Assigning a New IP Address to Your Camera ........................................................................................................ 7
Upgrading the Camera’s Firmware............................................................................................................................ 8
Accessing the Camera from a Web Browser ......................................................................................................... 9
3 Logging In and Viewing Live Video ......................................................................................................... 10
Logging In to the Camera via the Web Client ...................................................................................................10
Before You Begin ....................................................................................................................................................10
Logging in to the Camera ...................................................................................................................................10
Using the Main Page .....................................................................................................................................................14
System Menu ............................................................................................................................................................15
Stream Profile ...........................................................................................................................................................15
Camera Name ..........................................................................................................................................................16
Live View Tool Bar ...................................................................................................................................................16
Language ...................................................................................................................................................................16
User Account ............................................................................................................................................................16
4 Configuring Camera Settings ................................................................................................................... 18
Configuring General Settings ...................................................................................................................................18
Video Settings ..........................................................................................................................................................19
Day/Night Settings ................................................................................................................................................20
Configuring Video Settings ........................................................................................................................................21
Mode .............................................................................................................................................................................21
Video Stream .............................................................................................................................................................22
Configuring Audio Settings........................................................................................................................................26
Configuring IR Control Settings ..............................................................................................................................27
IR Illuminators ..........................................................................................................................................................27
Smart IR .......................................................................................................................................................................27
Configuring Image Settings ......................................................................................................................................28
White Balance ..........................................................................................................................................................28
Image Adjustment ..................................................................................................................................................29
Defog ............................................................................................................................................................................29
3D Noise Reduction ..............................................................................................................................................29
Configuring Exposure Settings ................................................................................................................................30
Measurement Window .........................................................................................................................................30

vi
 Exposure Control ....................................................................................................................................................31
AE Speed Adjustment ...........................................................................................................................................31
WDR ..............................................................................................................................................................................32
Configuring Focus ..........................................................................................................................................................32
Configuring Privacy Mask...........................................................................................................................................34
Configuring Privacy Mask (For HC60WZ2E30) ...............................................................................................35
5 Configuring PTZ Settings ........................................................................................................................... 36
PTZ Settings ......................................................................................................................................................................36
PTZ Operations ........................................................................................................................................................36
Home Location Settings .....................................................................................................................................37
Patrol List ...................................................................................................................................................................37
Misc Settings ............................................................................................................................................................40
Calibrate ..............................................................................................................................................................................41
Auto Tracking ....................................................................................................................................................................42
6 Configuring Network Settings .................................................................................................................. 44
Configuring Network General Settings ........................................................................................................44
Configuring Streaming Protocols...................................................................................................................47
Configuring DDNS Settings ..............................................................................................................................50
Configuring QoS Settings ..................................................................................................................................50
Configuring SNMP Settings ..............................................................................................................................52
Configuring HTTPS Settings .............................................................................................................................54
Configuring IEEE 802.1X Settings.................................................................................................................55
7 Configuring Video Analytics ...................................................................................................................... 57
Configuring Motion Detection Settings ..............................................................................................................57
Motion Detection ....................................................................................................................................................57
Configuring Tampering Detection Settings.......................................................................................................58
Configuring Alarm In and Alarm Out .....................................................................................................................59
Configuring Event Settings........................................................................................................................................59
Event .............................................................................................................................................................................60
Package Management .................................................................................................................................................67
8 Configuring Storage Settings ................................................................................................................... 69
SD Card Management ..................................................................................................................................................69
SD Card Status.........................................................................................................................................................70
SD Card Format .......................................................................................................................................................70
SD Card Control.......................................................................................................................................................71
Content Management ..................................................................................................................................................71
Searching and Viewing the Records ..............................................................................................................71
Search Results .........................................................................................................................................................72
Recording Settings.........................................................................................................................................................73
Adding a Recording Setting...............................................................................................................................74
Setting up a Recording ........................................................................................................................................75
9 Configuring System Settings .................................................................................................................... 77
Configuring System General Settings ..................................................................................................................77
Configuring Maintenance Settings .......................................................................................................................78

vii
 Upgrading Firmware .............................................................................................................................................79
Rebooting the Camera .........................................................................................................................................79
Restoring the Camera ..........................................................................................................................................79
Importing /Exporting Files .................................................................................................................................80
Configuring User Accounts Settings .....................................................................................................................82
Account Management .........................................................................................................................................83
Configuring Access List Settings ............................................................................................................................83
General Settings......................................................................................................................................................84
Filter ..............................................................................................................................................................................84
Administrator IP address ....................................................................................................................................85
10 Viewing System Information ..................................................................................................................... 86
Log .................................................................................................................................................................................86
Version .........................................................................................................................................................................87
11 Troubleshooting ............................................................................................................................................ 88
Troubleshooting for Common Issues ...................................................................................................................88
12 Appendix ........................................................................................................................................................... 89
List of Symbols .................................................................................................................................................................89

viii
Figures
Figure 2-1 Install Unified Tool .................................................................................................................................................... 4
Figure 2-2 Select Installation Folder ....................................................................................................................................... 4
Figure 2-3 Confirm Installation .................................................................................................................................................. 5
Figure 2-4 Splash Screen .............................................................................................................................................................. 6
Figure 2-5 Scanning the network .............................................................................................................................................. 6
Figure 2-6 Device List ..................................................................................................................................................................... 7
Figure 2-7 IP Assignment.............................................................................................................................................................. 7
Figure 2-8 Firmware Upgrade ..................................................................................................................................................... 8
Figure 2-9 Firmware Upgrade 2 ................................................................................................................................................. 9
Figure 3-1 Security Certificate Problem...............................................................................................................................11
Figure 3-2 Change Password ....................................................................................................................................................11
Figure 3-3 Login Page ..................................................................................................................................................................12
Figure 3-4 Safety Problem ..........................................................................................................................................................13
Figure 3-5 Security Certificate Problem...............................................................................................................................13
Figure 3-6 Change Password ....................................................................................................................................................13
Figure 3-7 Login Page ..................................................................................................................................................................14
Figure 3-8 Main Page ...................................................................................................................................................................14
Figure 3-9 PTZ Panel .....................................................................................................................................................................15
Figure 3-10 Live View Window Controls...............................................................................................................................16
Figure 3-11 User Account ...........................................................................................................................................................17
Figure 4-1 General Settings .......................................................................................................................................................19
Figure 4-2 Video Orientation .....................................................................................................................................................20
Figure 4-3 Mode ..............................................................................................................................................................................21
Figure 4-4 Video Stream ..............................................................................................................................................................23
Figure 4-5 Smart codec................................................................................................................................................................24
Figure 4-6 Audio ..............................................................................................................................................................................26
Figure 4-7 IR Control Settings ..................................................................................................................................................27
Figure 4-8 Image Settings ..........................................................................................................................................................28
Figure 4-9 Exposure ......................................................................................................................................................................30
Figure 4-10 AE Speed Adjustment .........................................................................................................................................31
Figure 4-11 WDR .............................................................................................................................................................................32
Figure 4-12 Focus...........................................................................................................................................................................33
Figure 4-13 Privacy Mask ...........................................................................................................................................................34
Figure 4-14 Configuring Privacy Mask (HC60WZ2E30) .............................................................................................35
Figure 5-1 PTZ Setup ....................................................................................................................................................................36
Figure 5-2 Patrol List.....................................................................................................................................................................37
Figure 5-3 Add A Recorded Patrol ...........................................................................................................................................38
Figure 5-4 Add A Preset Patrol..................................................................................................................................................39
Figure 5-5 Set a Patrol ..................................................................................................................................................................40
Figure 5-6 Misc Settings .............................................................................................................................................................40
Figure 5-7 Calibrate .......................................................................................................................................................................42
Figure 5-8 Auto Tracking .............................................................................................................................................................42
Figure 6-1 Network Type..............................................................................................................................................................44
Figure 6-2 Enable IPv6 .................................................................................................................................................................46
Figure 6-3 IPv6 Information.......................................................................................................................................................46
Figure 6-4 Manually setup IP Address ..................................................................................................................................47
Figure 6-5 Streaming Protocols - HTTP ...............................................................................................................................47
Figure 6-6 Streaming Protocols – RTSP ..............................................................................................................................48
Figure 6-7 Multicast Settings ...................................................................................................................................................49

ix
Figure 6-8 DDNS .............................................................................................................................................................................50
Figure 6-9 Cos ..................................................................................................................................................................................51
Figure 6-10 QoS/DSCP ................................................................................................................................................................52
Figure 6-11 SNMP Configurations.........................................................................................................................................53
Figure 6-12 HTTP ............................................................................................................................................................................54
Figure 6-13 Certificate Request...............................................................................................................................................54
Figure 6-14 Upload files ..............................................................................................................................................................55
Figure 6-15 IEEE 802.1X Configurations – EAP-PEAP ................................................................................................56
Figure 6-16 IEEE 802.1X Configurations – EAP-TLS....................................................................................................56
Figure 7-1 Configuring Motion Detection Settings .......................................................................................................58
Figure 7-2 Tampering Detection Configurations ............................................................................................................58
Figure 7-3 Alarm In and Alarm Out .........................................................................................................................................59
Figure 7-4 Event Settings ..........................................................................................................................................................60
Figure 7-5 Event ..............................................................................................................................................................................61
Figure 7-6 Trigger Sources .........................................................................................................................................................62
Figure 7-7 Action .............................................................................................................................................................................63
Figure 7-8 Add Server ....................................................................................................................................................................64
Figure 7-9 Server type – HTTP ..................................................................................................................................................64
Figure 7-10 Add Media .................................................................................................................................................................65
Figure 7-11 Event Settings Examples ..................................................................................................................................67
Figure 7-12 Package Management .......................................................................................................................................67
Figure 8-1 No SD Card..................................................................................................................................................................70
Figure 8-2 SD Card Onboard .....................................................................................................................................................70
Figure 8-3 SD Card Format ........................................................................................................................................................70
Figure 8-4 SD Card Control ........................................................................................................................................................71
Figure 8-5 Search ............................................................................................................................................................................72
Figure 8-6 Search Results...........................................................................................................................................................72
Figure 8-7 Play Search Result ...................................................................................................................................................73
Figure 8-8 Recording Settings ..................................................................................................................................................73
Figure 8-9 Recording Settings Details ..................................................................................................................................74
Figure 8-10 Recording 1 ..............................................................................................................................................................76
Figure 9-1 Configuring System General Settings ...........................................................................................................77
Figure 9-2 Maintenance ..............................................................................................................................................................78
Figure 9-3 Import/Export Files .................................................................................................................................................80
Figure 9-4 Account Management ...........................................................................................................................................83
Figure 9-5 Access List...................................................................................................................................................................84
Figure 10-1 System Log ..............................................................................................................................................................86
Figure 10-2 Access Log ...............................................................................................................................................................87

x
Tables
Table 3-1 Live View Window Controls ...................................................................................................................................16
Table 4-1 Stream and Frame Size Matrix ............................................................................................................................23
Table 8-1 Compatible SD Card .................................................................................................................................................69
Table 11-1 Troubleshooting ......................................................................................................................................................88

xi
About This Document
This document provides instructions for accessing, configuring, and operating the Honeywell
60 Series IP cameras. This document is intended for system installers, administrators, and
operators.

Overview of Contents
This document contains the following chapters and appendixes:
• Chapter 1, Introduction, provides an overview of the main features of the Honeywell 60
Series IP cameras.
• Chapter 2 , Accessing the Camera, describes how to install the Unified Tool to access the
camera remotely from a web browser. It also describes how to update your camera’s
firmware.
• Chapter 3, Logging In and Viewing Live Video, describes how to log in to a camera and
using the main page.
• Chapter 4, Configuring Camera Settings, describes how to configure the camera settings.
• Chapter 5, Configuring PTZ Settings, describes how to configure the PTZ settings.
• Chapter 6, Configuring Network Settings, describes how to configure the network settings.
• Chapter 7, Configuring Video Analytics, describes how to configure video analytics.
• Chapter 8, Configuring Storage Settings, describes how to configure storage settings.
• Chapter 9, Configuring System Settings, describes how to configure general system
settings.
• Chapter 10, Viewing System Information, describes how to view system log, access log and
firmware version.
• Chapter 11, Troubleshooting, lists common problems and solutions.
• Chapter 12, Appendix, lists the descriptions of symbols.

i
 Introduction

1 Introduction
This chapter contains the following sections:
• Overview, page 1
• Key Features, page 1

Overview
Honeywell 60 Series IP cameras integrate traditional camera and network video technology,
combining video data collection and transmission. These flexible, fully featured cameras are
the ideal choice for a wide range of indoor and outdoor surveillance applications.
The cameras offer 2, 4 or 5 megapixel resolution at up to 60 frames per second and use video
compression technology to save bandwidth and storage while ensuring maximum video
quality. All the cameras are True Day/Night with intelligent IR capability, providing up to 197 ft
(60 m) of illumination in low-light and nighttime scenes. Also, all the cameras support WDR
function at up to 120 dB.
Each camera comes with configurable motion detection and camera tamper detection and
supports up to 5 user-defined privacy mask areas. In addition to a 12 VDC adapter (for IPC
models) or 24 VAC/VDC adapter (for PTZ models), all the cameras support Power over
Ethernet (PoE), eliminating the need for a separate power supply and associated wiring. All
models also support local video storage on microSDHC cards (up to 256 GB) when network
service is interrupted.

Key Features
Key features of the Honeywell 60 Series IP cameras include the following:
Camera
• Up to 5MP (2560x1920) cameras.

• Video parameter setup, such as electronic shutter and gain.

• Motion detection.

• Camera tampering detection.

• True WDR (120 dB).

• True day/night mode using a removable IR cut filter.

• Low-light with 2D/3D noise reduction saving storage and bandwidth together
with smart codec.
• Built-in G sensor for third party application integration.

• For use as part of Video Systems which comply with NDAA Section 889.

1
Honeywell 60 Series IP Camera Software Configuration Guide

• PTZ settings (only for HC60WZ2E30).

• FIPS chipset build-in

Storage
• Central server backup (configure in Event settings).

• Recording over Internet, files stored on client PC.

Network
• Up to 10 connections.

• Compatible with the following network protocols: IPv4, IPv6, TCP/IP, HTTP, HTTPS, UPnP,
RTSP/RTP/RTCP, IGMP/Multicast, SMTP, DHCP, NTP, DNS, DDNS, CoS, QoS, SNMP,
802.1X, UDP, ICMP, ARP, TLS.
• Support the following security modes: User account and password protection, HTTPS, IP
Filter, Digest authentication, TLS1.2 only, Stream encryption, AES128/256, SSH/Telnet
closed, PCIDSS compliance, FIPS Chipset Built-In.
• Support the following languages: English, French, German, Italian, Japanese, Portuguese,
Russian, Spanish, Traditional Chinese.
• Camera configuration and management via Ethernet.
Events and Analytics
• Support the following Video Analytics types: Intrusion, loiter, line crossing, unattended
object, missing object, face detection.
• Support the following event types: Video motion detection, Periodically, Alarm input,
System boot, Recording notification, Camera tampering detection.
• Support the following event linkage mode: Event notification using digital output, HTTP,
Email and MicroSD card.
User Management
• Each user belongs to specific group.

• Different user rights for each group.

System Management
• Log function.

• Support controlling access permission by verifying the client PC’s IP address.

• System resource information and running real-time status display.

2
 Accessing the Camera

2 Accessing the Camera

This chapter contains the following sections:
• Installing the IPC Tool Utility, page 3
• Discovering Your Camera on the Network, page 3
• Assigning a New IP Address to Your Camera, page 7
• Upgrading the Camera’s Firmware, page 7
• Accessing the Camera from a Web Browser, page 8

Installing the Unified Tool

To get the installation package of Unified Tool:
• Browse to https://mywebtech.honeywell.com, login, navigate to Download Center  Video
 IP Cameras  Camera Discovery Tools & Utilities  Honeywell Unified Tool, and then
download the installation package of Unified Tool to your computer. You need to unzip
the package.
• Copy the installation package of Unified Tool from the CD along with the package of the
camera to your computer.
To install the Unified Tool:

1. Double-click the installation program in the installation package to install the Unified
Tool.

3
Honeywell 60 Series IP Camera Software Configuration Guide

Figure 2-1 Install Unified Tool

2. Click Next and the following figure is displayed:

Figure 2-2 Select Installation Folder

3. Follow the on-screen instructions to configure your settings and click Next and the
following figure is displayed:

4
 Accessing the Camera

Figure 2-3 Confirm Installation

4. Click Next and the installer will install Unified Tool on your computer. After the installation
is completed, click Close. A shortcut of Unified Tool will be displayed on the desktop.

Discovering Your Camera on the Network

Double-click on the desktop and the following figure is displayed:

5
Honeywell 60 Series IP Camera Software Configuration Guide

Figure 2-4 Splash Screen

1. Select your language from the dropdown list of Language. Currently, only English is
supported.
2. Check “Don’t show the splash window on startup” and this page can be skipped next time.
If you want to check the splash window again, click as shown in Figure 2-6 and select
the checkbox of Show the splash page on startup.
3. Click CONTINUE. It will scan devices in the network automatically.
Figure 2-5 Scanning the network

After the scanning, all scanned devices in the same subnet and different subnet will be
displayed in the devices list.

6
 Accessing the Camera

Figure 2-6 Device List

Assigning a New IP Address to Your Camera

The current IP address of your camera appears in the IP ADDRESS column of the devices list.
If you want, you can assign a new static IP address to the camera.

Select the target device(s) as shown in Figure 2-6, click and the following figure is
displayed:
Figure 2-7 IP Assignment

7
Honeywell 60 Series IP Camera Software Configuration Guide

Configure IP Address Setting

• To obtain IP address, subnet mask, and default gateway settings automatically, select the
check box of DHCP.
• To configure IP address, subnet mask, and default gateway settings manually, select the
check box of Manual and enter the settings. If you enter the start IP address, the system
can calculate the end IP address automatically according to the number of your selected
device(s).
• After all settings are completed, click APPLY.

Configure DNS Server Address

• To obtain the DNS server address automatically, select the check box of Obtain
automatically.
• To manually enter the DNS server address, select the check box of Manual assignment
and enter the settings.
• After all settings are completed, click APPLY.

Upgrading the Camera’s Firmware

Before you begin using your camera, make sure you have the latest firmware installed. You
can upgrade a single camera or multiple cameras at the same time.
Select the Maintenance tab from the left pane as shown in Figure 2-6, select target device(s)

and click and the following window is displayed:

Figure 2-8 Firmware Upgrade

The devices were grouped by model. To upgrade the firmware:

1. Select the target device(s) under a model.
2. Click BROWSE and select the upgrade file from your computer.

8
 Accessing the Camera

Figure 2-9 Firmware Upgrade 2

3. Click APPLY. You can check the progress status in the device list.

Accessing the Camera from a Web Browser

To access the camera from a web browser, click next to the IP address of the device as
shown in Figure 2-6.

9
Honeywell 60 Series IP Camera Software Configuration Guide

3 Logging In and Viewing Live

Video
This chapter contains the following sections:
• Logging In to the Camera via the Web Client, page 10
• Using the Main Page, page 14

Logging In to the Camera via the Web Client

Using the web client, you can monitor live video, play back recorded video, and configure
camera settings.

Before You Begin

Before you log in to the web client, ensure that the following conditions are met:
• The camera is properly connected to the network.
• The camera’s IP address and the PC’s IP address are in the same network segment. If
there is a router, set the corresponding gateway and subnet mask.
• A network connection has been established. To check this, ping the camera’s IP address.
(Enter "ping [IP address]").

Logging in to the Camera

Logging in via Internet Explorer
1. Open Internet Explorer, type the camera’s IP address in the address bar, and then click
Enter. For example, if your camera’s IP address is 192.168.1.108, you would type
https://192.168.1.108.

Note Internet Explorer 11 with ActiveX plug-in is supported.

2. The following window is displayed. Click Continue to this website (not recommended).

10
 Logging In and Viewing Live Video

Figure 3-1 Security Certificate Problem

For how to resolve the security certificate problem, see Export CA Certificate on page 81.
3. For security purposes, you are required to create a new secure password at the first login.
Figure 3-2 Change Password

The password must be at least 8 characters in length and contain at least one uppercase
letter, one lowercase letter, one number, and one special character (!?@#$%=+*-_:,.&^~).
The password cannot be blank. Click SAVE.
4. The login screen is displayed. Enter the admin user name and password, and then click
LOGIN.

11
Honeywell 60 Series IP Camera Software Configuration Guide

Figure 3-3 Login Page

If you are logging in for the first time, you will be prompted to download and install the plugin.
Follow the on-screen instructions to install it. When the installation is complete, the web
client automatically refreshes and the main page opens (Figure 3-7).

Logging in via Google Chrome

1. Open Google Chrome, type the camera’s IP address in the address bar, and then click
Enter. For example, if your camera’s IP address is 192.168.1.108, you would type
https://192.168.1.108.

Note Chrome 79.0 is supported.

2. The following window is displayed. Click Advanced.

12
 Logging In and Viewing Live Video

Figure 3-4 Safety Problem

3. The following window is displayed. Click Proceed to 192.168.1.108 (unsafe).

Figure 3-5 Security Certificate Problem

For how to resolve the security certificate problem, see Export CA Certificate on page 81.
5. For security purposes, you are required to create a new secure password at the first login.
Figure 3-6 Change Password

The password must be at least 8 characters in length and contain at least one uppercase
letter, one lowercase letter, one number, and one special character (!?@#$%=+*-_:,.&^~).
The password cannot be blank. Click SAVE.
4. The login screen is displayed. Enter the admin user name and password, and then click
LOGIN.

13
Honeywell 60 Series IP Camera Software Configuration Guide

Figure 3-7 Login Page

Using the Main Page

The main page includes the following areas: system menu, live view tool bar, language
selection and user account settings.
Figure 3-8 Main Page

For PTZ model, a PTZ panel can be accessed by clicking on the right.

14
 Logging In and Viewing Live Video

Figure 3-9 PTZ Panel

For details on PTZ operation, see Configuring PTZ Settings on page 36.

System Menu
When you log in to the camera using the web client, the main page opens by default. To
access the setup page or information page, select the corresponding tab.

Stream Profile
To set the stream profile, in the Stream Profile list, select Main Stream, Sub Stream, or Third
Stream.
Main Stream Delivers high definition video for real-time monitoring, recording, and
storage. Uses the most bandwidth.
Sub Stream Delivers low/standard definition video, typically for remote monitoring in
lower network bandwidth environments.
Third Stream Delivers low definition video.
The properties for each stream type are configured on the Setup  Camera Setup  Video
page (see Configuring Video Settings on page 21).

15
Honeywell 60 Series IP Camera Software Configuration Guide

Camera Name
You can change the camera name according to your needs. For more information, see
Configuring System General Settings on page 77.

Live View Tool Bar

From the Live View toolbar, you can zoom in on a scene, take a snapshot, or manually record
video. These controls are described in more details below.
Figure 3-10 Live View Window Controls

Table 3-1 Live View Window Controls

Icon Description
Click to turn on the audio to listen to the monitoring site. Click
it again to turn off the audio. (The audio couldn’t be closed in
the Chrome browser)
Click to switch to the full screen mode. Press the “Esc” key or
double click the screen to switch to the normal mode.
Click to auto fit the image. (This function is not applicable in the
Chrome browser)
Click and uncheck Disable digital zoom in the pop up window
to enable the zoom operation. The navigation screen shows the
part of the image being magnified. To resize the navigation
area, drag the border. To move to a different area you want to
magnify, drag the navigation screen. To zoom the image, scroll
the mouse wheel. (This function is not applicable in the
Chrome browser)
Click to capture and save video images. The captured images
will be displayed in a pop-up window. Right click the image and
select Save picture as to save it in JPEG (*.jpg) or BMP
(*.bmp) format.

Language

To switch a language, click as shown in Figure 3-8.

User Account

To configure user account or log out the current account, click as shown in Figure 3-8
and the following figure is displayed:

16
 Logging In and Viewing Live Video

Figure 3-11 User Account

To configure the user account, click SETTINGS. For details, see Configuring User Accounts
Settings on page 82.
To log out the current account, click LOG OUT.

17
Honeywell 60 Series IP Camera Software Configuration Guide

4 Configuring Camera Settings

This chapter contains the following sections:
• Configuring General Settings, page 18
• Configuring Video Settings, page 21
• Configuring Audio Settings, page 26
• Configuring IR Control Settings, page 27
• Configuring Image Settings, page 28
• Configuring Exposure Settings, page 30
• Configuring Focus, page 32
• Configuring Privacy Mask, page 34
• Configuring Privacy Mask (For HC60WZ2E30), page 35

Click SAVE to enable the settings after you completed the settings
Note
on each page.

Configuring General Settings

Go to Setup Camera SetupGeneral Settings.
On this page, you can configure the general video settings and day/night settings.

18
 Configuring Camera Settings

Figure 4-1 General Settings

Video Settings
Video Title: Enter a name that will be displayed on the title bar of the live video.
Show times tamp and video title in video and snapshots: Check to display timestamp and
video title in live video and snapshots.
G Sensor XYZ value: Check to display G-sensor XYZ value on the screen. The G-sensor XYZ
value is recommended for the third party platform to perform data conversion.
Location of time stamp and video title on image: Select a position from the dropdown list to
display timestamp and video title on the top or at the bottom of the video stream.
Time stamp and video title font-size: Select a font size for the timestamp and title.
Camera font (.ttf): You can select a True Type font file for the display of textual messages on
video.
Color: Select to display color or black/white video streams.
Video Standard: Select the video standard: NTSC or PAL.

If the video standard is changed, you must disconnect and

Note reconnect the power cord of the camera in order for the new
setting to take effect.

Video orientation:
• Flip: vertically reflect the display of the live video;
• Mirror: horizontally reflect the display of the live video.

19
Honeywell 60 Series IP Camera Software Configuration Guide

• Select both Flip and Mirror if the camera is installed upside-down (e.g., on the ceiling) to
correct the image orientation.
• Rotate: Rotate the video by 90 degrees or 270 degrees. The rotation here indicates
clockwise rotation. Rotation can be applied with flip, mirror, and physical lens rotation
settings to adapt to different mounting locations, such as a corridor.
Figure 4-2 Video Orientation
Rotate 90
Original Flip Original Mirror Original degrees
(clockwise)

The flip/mirror/rotate operation will clear the video settings,

Note privacy mask settings, exposure window, motion detection
settings, preset position and focus window.

Day/Night Settings
Switch to B/W in night mode: Check to enable the camera to automatically switch to
Black/White during night mode.
Mode:
• Auto mode (The Day/Night Exposure Profile will not be available if Auto mode is selected)
The camera automatically removes the filter by judging the level of ambient light.

Note Select auto mode will disable profile of exposure settings.

• Day mode
In day mode, the camera switches on the IR cut filter at all times to block infrared light
from reaching the sensor so that the colors will not be distorted.
• Night mode
In night mode, the camera switches off the IR cut filter at all times for the sensor to accept
infrared light, thus helping to improve low light sensitivity.
• Schedule mode
The camera switches between day mode and night mode based on a specified schedule.
Enter the start and end time for day mode. The time format is [hh:mm] and is expressed in
24-hour clock time. By default, the start and end time of day mode are set to 07:00 and
18:00.

20
 Configuring Camera Settings

Sensitivity: Adjust the responsiveness of the IR filter to lighting conditions as Low, Normal, or
High.

Configuring Video Settings

Go to Setup Camera Setup  Video.
This section describes how to configure viewing window and video streaming properties
(format, resolution, frame rate, bit rate, I-frame interval, etc.).

Mode
Go to Setup Camera Setup  Video Mode.
Figure 4-3 Mode

5-Megapixel (4:3) (MAX 30fps): Select it and the maximum resolution will be 2560x1920.
The aspect ratio will be 4:3.
4-Megapixel (16:9) (Max 60fps Non-True WDR): Select it and the maximum resolution will
be 2560x1440. The aspect ratio will be 16:9.
2-Megapixel (16:9) (Max 60fps): Select it and the maximum resolution will be 1920x1080.
The aspect ratio will be 16:9.
2-Megapixel (16:9) (Max 30fps): Select it and the maximum resolution will be 1920x1080.
The aspect ratio will be 16:9.

• 5-Megapixel and 4-Megapixel are applicable for

HC60W35R2/HC60W45R2/HC60WB5R2/HC60W35R4/HC60W45R4/HC60
Note WB5R5.
• 2-Megapixel is applicable for HC60WZ2E30.

Changing the video mode will clear the following settings: privacy mask, exposure
Note
widow, motion, preset position and focus window.

21
Honeywell 60 Series IP Camera Software Configuration Guide

Video Stream
Go to Setup Camera Setup  Video Stream.
See the following table for streams and frame sizes of each model:

22
 Configuring Camera Settings

Table 4-1 Stream and Frame Size Matrix

Model Main Stream Sub Stream Third Stream

2560×1440/ 2560×1440/
1920×1080/ 1920×1080/
1600×904/ 1600×904/
1360×768/ 1360×768/
1280×720/ 1280×720/ 1280x960/
HC60W35R2/
640×360 640×360 640x480
HC60W35R4/
(1-25/30fps), (1-25/30fps), (1-25/30fps),
HC60W45R2/
1920x1080/ 1920x1080/
HC60W45R4/ 1280x720/
1600x904/ 1600x904/
HC60WB5R2/ 640x360
1360x768/ 1360x768/
HC60WB5R5
1280x720/ 1280x720/ (1-50/60fps)
640x360 640x360
(1-50/60fps), (1-50/60fps),
2560x1440 2560x1440
(1-50fps) (1-50fps)
1920×1080/
1280x720/
HC60WZ2E30 1280x720/ 640x360
640x360
640x360

Figure 4-4 Video Stream

Frame size
Set different video resolutions for different viewing devices. For example, you can configure a
smaller frame size and lower bit rate for remote viewing on mobile phones and a larger video
size and a higher bit rate for live viewing on web browsers, or recording the stream to an NVR.
A larger frame size takes up more bandwidth.

23
Honeywell 60 Series IP Camera Software Configuration Guide

Maximum frame rate

This limits the maximum refresh frame rate per second. Set the frame rate higher for
smoother video quality and for recognizing moving objects in the field of view.
If the power line frequency is set to PAL, the frame rates are selectable from 1-50 fps. If the
power line frequency is set to NTSC, the frame rates are selectable from 1-60 fps. You can
also select Customized and manually enter a value.
The frame rate will decrease if you select a higher resolution.

Intra frame period

Determine how often for firmware to plant an I frame. The shorter the duration, the more likely
you will get better video quality, but at the cost of higher network bandwidth consumption.
Select the intra frame period from the following durations: 1/4 second, 1/2 second, 1 second,
2 seconds, 3 seconds, and 4 seconds.

Smart codec configuration

Dynamic Intra frame period

High quality motion codecs, such as H.265, utilize the redundancies between video frames to
deliver video streams at a balance of quality and bit rate. The encoding parameters are
summarized and illustrated below. The I-frames are completely self-referential and they are
largest in size. The P-frames are predicted frames. The encoder refers to the previous I- or P-
frames for redundant image information.

Smart FPS
In a static scene, the algorithm puts old frames in queue when no motions occur in scene.
When motions occur, the encoding returns to normal to deliver real-time streaming.
By queuing the old frames from a static scene, both the computing efforts and the size of P
frames are reduced. It is beneficial for keeping up with the frame rate requirements.
A default frame difference threshold, 1%, is embedded in firmware for returning from Smart
FPS to normal encoding when motions occur.

Smart codec
Smart codec effectively reduces the quality of the whole or the non-interested areas on a
screen and therefore reduces the bandwidth consumed.
You can manually specify the video quality for the foreground and the background areas.
Figure 4-5 Smart codec

24
 Configuring Camera Settings

Select an operation mode if Smart codec is preferred.

• Auto tracking: The Auto mode configures the whole screen into the non-interested area.
The video quality of part of the screen returns to normal when one or more objects move
in that area. The remainder of the screen where there are no moving objects (no pixel
changes) will still be transmitted in low-quality format.
• Manual: The Manual mode allows you to configure 3 ROI windows (Region of Interest,
with Foreground quality) on the screen. Areas not included in any ROI windows will be
considered as the non-interested areas. The details in the ROI areas will be transmitted in
a higher-quality video format.
• Hybrid: The major difference between the “Manual” mode and the “Hybrid” mode is that:
In the “Hybrid“ mode, any objects entering the non-interested area will restore the video
quality of the moving objects and the area around them. The video quality of the
associated non-interested area is immediately restored to normal to cover the moving
objects.
In the “Manual” mode, the non-interested area is always transmitted using a low-quality
format regardless of the activities occurring inside.
• Quality priority: Drag the slider to adjust the quality contrast between the ROI and non-
interested areas.
• The farther the slider is to the right, the higher the image quality of the ROI areas.
• On the contrary, the farther the slider to the left, the higher the image quality of the
non-interested area.
In this way, you may set up an ROI window as a privacy mask by covering a protected area
using an ROI window, while the rest of the screen becomes the non-interested area. You
may then configure the non-interested area to have a high image quality, or vice versa.

Bit rate control

Constrained bit rate

A complex scene generally produces a larger file size, meaning that higher bandwidth will be
needed for data transmission. The bandwidth utilization is configurable to match a selected
level, resulting in mutable video quality performance.
• Image quality: Select a desired quality ranging from Medium to Excellent. If you select
Customized, you can enter a value to specify the quality.
• Maximum bit rate: Select a bit rate from the dropdown list. The bit rate ranges from 20
Kbps to a maximum of 80 Mbps. If you select Customized, you can enter a value to
specify the maximum bit rate.
• Priority: If Frame rate is selected, the camera will try to maintain the frame rate per
second performance, while the image quality will be compromised. If Image quality is
selected, the camera may drop some video frames in order to maintain image quality.

Fixed quality
All frames are transmitted with the same quality.
• Quality: Select a desired quality ranging from Medium to Excellent. If you select
Customized, you can enter a value to specify the quality.

25
Honeywell 60 Series IP Camera Software Configuration Guide

• Maximum bit rate: Select a bit rate from the dropdown list. The bit rate ranges from 1
Mbps to a maximum of 40Mbps. If you select Customized, you can enter a value to
specify the maximum bit rate.
The Maximum bit rate setting in the Fixed quality configuration can ensure a reasonable
and limited use of network bandwidth. For example, in low light conditions where a Fixed
quality setting is applied, video packet sizes can tremendously increase when noises are
produced with electrical gains.

Configuring Audio Settings

Go to Setup Camera Setup  Audio.
Figure 4-6 Audio

Mute: Check to disable audio transmission from the Network Camera to all clients.
Microphone source: Select Internal or External from the dropdown list.

The Internal microphone source is applicable for HC60W35R2 &

Note
HC60W35R4.

Internal microphone input gain: Select the gain of the internal audio input according to
ambient conditions. Adjust the gain from 0% (least) to 100% (most).

The Internal microphone input gain is applicable for HC60W35R2

Note
& HC60W35R4.

External microphone input gain: Select the gain of the external audio input according to
ambient conditions. Adjust the gain from 0% (least) to 100% (most).
Audio type: Select audio codec as G.711 or G.726 and the bit rate.

26
 Configuring Camera Settings

• G.711 provides good sound quality and requires about 64Kbps. Select pcmu (μ-Law) or
pcma (A-Law) mode.
• G.726 is a speech codec standard covering voice transmission at rates of 16, 24, 32, and
40kbit/s.
After you complete the settings on this page, click SAVE to enable the settings.

Configuring IR Control Settings

Go to Setup Camera SetupIR Control.
On this page, you can turn on the IR illuminator and adjust the luminance of IR lights.
Figure 4-7 IR Control Settings

IR Illuminators
Turn on built-in IR illuminator in night mode: Check to turn on the camera’s onboard IR
illuminator when the camera detects low light condition and enters the night mode.
Turn on external illuminator in night mode: Check the connector type to turn on the
camera’s external IR illuminator when the camera detects low light condition and enters the
night mode. You should connect an alarm output first.

The built-in IR illuminator function is not applicable for

Note
HC60WZ2E30.

Smart IR
Anti-overexposure: When checked, the camera automatically adjusts the shutter speed, Gain
and IRIS through algorithm of the firmware in order to avoid over-exposure in the night mode.

27
Honeywell 60 Series IP Camera Software Configuration Guide

IR Adjustment: Adjust the luminance of IR lights.

• Auto IR adjust: Select it to control the luminance of IR lights automatically.
• Manual IR adjust: Select it to control the luminance of IR lights manually. To increase the
luminance of IR lights, drag the slider to the right; to decrease the luminance of IR lights,
drag the slider to the left.

Note The Smart IR function is not applicable for HC60WZ2E30.

Configuring Image Settings

Go to Setup Camera Setup  Image Settings.
On this page, you can configure the White balance and adjust Image parameters.
Two sets of image settings are available:
• In Normal Light Mode tab, configure normal situations for image settings.
• In Profile Mode tab, configure special situations for image settings.
• Night Mode: Check Enable to apply these settings at and select this mode to apply
the settings at night.
• Schedule Mode: Check Enable to apply these settings at and select this mode to
apply the settings at a specific period. Enter the time manually in the field.
Figure 4-8 Image Settings

White Balance
Adjust the value for the best color temperature.
Auto: Select it and the camera will automatically adjust the color temperature.

28
 Configuring Camera Settings

Fixed current: Select it and the camera will use current color temperature value.
Manual: You may manually tune the color temperature by dragging the R Gain and B Gain
slider.

Image Adjustment
Brightness: Adjust the image brightness level (0% to 100%).
Contrast: Adjust the image contrast level (0% to 100%).
Saturation: Adjust the image saturation level (0% to 100%).
Sharpness: Adjust the image sharpness level (0% to 100%).
Gamma curve: Adjust the image sharpness level (0.45 to 1, Detailed to Contrast).
• Optimize: The system automatically adjusts the gamma curve.
• Manual: Drag the slider to change the preferred level of Gamma correction towards higher
contrast or towards the higher luminance for detailed expression for both dark and
lighted areas of an image.

The Gamma curve function is disabled when the WDR feature in

Note
Exposure settings is enabled.

Defog
Check to improve the visibility quality of captured image in poor weather conditions such as
smog, fog, or smoke.

3D Noise Reduction
Drag the slider to adjust the reduction strength (from low to high).

3D Noise Reduction is mostly applied in low-light conditions. In a

Note low-light condition with fast moving objects, trails of after-images
may occur. You may then select a lower strength level.

All changes made to image settings are directly shown on screen.

Note To recall the original settings without incorporating the changes,
click RESTORE. After you completed the settings, click SAVE.

29
Honeywell 60 Series IP Camera Software Configuration Guide

Configuring Exposure Settings

Go to Setup Camera Setup  Exposure.
On this page, you can set the Exposure measurement window, Exposure level, Exposure
mode, Exposure time, Gain control, and Day/Night mode settings.
Two sets of exposure settings are available:
• In Normal Light Mode tab, configure normal situations for image settings.
• In Profile Mode tab, configure special situations for image settings.
• Night Mode: Check Enable to apply these settings at and select this mode to apply
the settings at night.
• Schedule Mode: Check Enable to apply these settings at and select this mode to
apply the settings at a specific period. Enter the time manually in the field.
Figure 4-9 Exposure

Measurement Window
Measurement Window: This function allows users to set measurement window(s) for low light
compensation. For example, where low-light objects are posed against an extremely bright
background. You may want to exclude the bright sunlight shining through a building's
corridor.
• Full view: Calculate the full range of view and offer appropriate light compensation.
• Custom: Manually add customized windows as inclusive or exclusive regions. A total of 10
windows can be configured.
The inclusive windows have a higher priority. You can overlap these windows, and, if you
place an exclusive window within a larger inclusive window, the exclusive part of the
overlapped windows will be deducted from the inclusive window. An exposure value will
then be calculated out of the remaining of the inclusive window.
• Center: This option will automatically add an inclusive window in the middle of the window
and give the necessary light compensation.

30
 Configuring Camera Settings

• HLC (Highlight Compensation): Firmware detects strong light sources and compensates
on affected spots to enhance the overall image quality. For example, the HLC helps
reduce the glares produced by spotlights or headlights.

Exposure Control
Exposure level: You can manually set the exposure level, which ranges from -2.0 to +2.0 (dark
to bright) (for IPC model) or from -0.7 to +0.7 (for PTZ model).
Exposure mode: Select an exposure mode (Auto or Manual) from the dropdown list.
• If you select Auto, you can set the Iris mode to Outdoor or Indoor.
• If you select Manual, you can drag the slider of Iris adjustment, Exposure time and Gain
Control to get the best image quality.

Note The exposure mode function is not applicable for HC60WZ2E30.

Flickerless: Check to reduce flicker in the image.

AE Speed Adjustment
Check Enable AE speed adjustment to apply it in fast changing lighting conditions, such as a
highway lane or entrance of a parking area at night where cars passing by with their lights on
and it can bring fast changes in light levels. It is also applicable to a situation if the camera is
installed on a vehicle, and when it needs to adapt to fast changes of light when entering and
leaving a tunnel.
Figure 4-10 AE Speed Adjustment

The AE Speed Adjustment function is not applicable for

Note
HC60WZ2E30.

31
Honeywell 60 Series IP Camera Software Configuration Guide

WDR
Figure 4-11 WDR

True WDR: Check to enable the Wide Dynamic Range function which can capture details in a
high contrast environment. Use the slide bar to select the strength (from Low to High),
depending on the lighting condition at the installation site. You can select a higher effect
when the contrast is high (between the shaded area and the light behind the objects).
Digital WDR: Check to enable the Digital Wide Dynamic Range function. Use the slide bar to
select the strength (from Low to High).
Digital WDR is a software-based technique that enhances the image quality by adjusting the
gamma value to brighten dark areas. True WDR is a sensor-based technology. A True WDR
CCTV can produce images with an extremely wide dynamic range. The WDR image sensor can
capture several images with short and long exposures, then combining them into a single
frame.

Configuring Focus

Note The Focus function is not applicable for HC60WZ2E30.

Focus here refers to the Remote Focus, applicable to the cameras that are equipped with a
stepping motor lens. The automated focus adjustment function eliminates the needs to
physically adjust camera focus. In an outdoor deployment consisting of a large number of
cameras, the auto focus function can be very helpful when these cameras become out of
focus after days or weeks of operation. And that can easily result from the effects of natural
forces, e.g., shrink and expand due to a wide range of operating temperatures and the
vibration caused by wind.
Go to Setup Camera Setup  Focus.

32
 Configuring Camera Settings

Figure 4-12 Focus

• To zoom in on an image, drag the slider to the right.

• To zoom out on an image, drag the slider to the left.

• To fine-tune the zoom, click or .

If you are not satisfied with the results of zooming, click PERFORM
AUTO FOCUS. It may take about 15 to 20 seconds (full-range scan
Note unchecked) or 30 to 80 seconds (full-range scan checked) to
perform the auto focus scan. You may still need to fine-tune the
focus depending on the live image on your screen.

To perform the automated Focus function:

1. Select from the bottom of the screen whether you want to perform focus adjustment on
the Full view or within a Custom focus window. You can create a custom window and click
and drag the window to a desired position on screen.
2. It is recommended to Reset to the default back focus position of the sensor board.
3. You can check Fully-opened iris (default) to increase the iris size for a better focus
adjustment result.
4. Check Fully-opened iris or Full-range scan buttons.
Full-range scan: Check it and a full-range scan through the camera's entire focal length
can take about 30 to 80 seconds. If it is not checked, the auto focus scan will only go
through the length where optimal focus may occur, and that takes about 15 to 20
seconds. In theory, best results of the auto scan can be acquired when the camera's iris is
fully open.
5. Wait for the scan to complete. After a short while, the clearest image obtained should be
displayed and the optimal focus range achieved. Use the arrow marks on the sides to fine-
tune the focus if you are not satisfied with the results. You may still need to use the arrow
marks to fine-tune the focus depending on the live image on your screen. “>” means
moving from wide to tele end; and “<” tele to wide.
Focus window:

33
Honeywell 60 Series IP Camera Software Configuration Guide

By default, the optimal focus is found on a full view window. You may designate a custom
window within your current field of view to acquire the best focus out of it. However, you
cannot place a focus window on a distant background, e.g., a hall way that stretches away for
3 meters or farther. Doing so you will not benefit from the Focus window function.
• Full view: The focus tuning takes place by referring to the full view.
• Custom: You can create a focus window and drag it to a place of interest in your view
window.

It is recommended that this function be used only when you have a

solid object in your view window that is showing a consistent color or
Note
texture. This function will not take effect if you set the focus window
on a distant background.

Configuring Privacy Mask

On this page, you can block out sensitive view areas to address privacy concerns.
Go to Setup Camera Setup  Privacy Mask.
To configure privacy masks for Non-PTZ models:
1. Click NEW to add a new privacy mask window on the video screen.
2. Use 4 mouse clicks to create a new masking window, which is recommended to be at least
twice the size of the object (height and width) you want to cover.
3. Enter a name for the privacy mask and click SAVE to enable the setting.
4. Check Enable privacy mask to enable this function.
Figure 4-13 Privacy Mask

34
 Configuring Camera Settings

• Up to 5 privacy mask windows can be configured on the

same screen.
Note
• If you want to delete the privacy mask window, click the ‘x’
mark on the right side of privacy mask window name.

Configuring Privacy Mask (For HC60WZ2E30)

To configure privacy masks for HC60WZ2E30:
1. Click the Enable privacy mask checkbox to enable this function and click SAVE.
2. Click NEW to add a privacy mask window on the video screen.
3. Enter a name for the privacy mask window.
4. Use mouse clicks on the screen to move to a place where you want to create a mask. You
can also use the PTZ panel to fine-tune the move to the target area. For how to use the
PTZ panel, see PTZ Operations on page 36.
5. If preferred, move the field of view to other places to create more privacy masks.
Figure 4-14 Configuring Privacy Mask (HC60WZ2E30)

• The navigation buttons here also support the continuous move. You can
click and hold down the button to move across the screen until you
release the button.
Note • Up to 24 privacy mask windows can be configured over the camera's
hemispheric coverage.
• If you want to delete the privacy mask window, click the ‘x’ mark on the
right side of privacy mask window name.

35
Honeywell 60 Series IP Camera Software Configuration Guide

5 Configuring PTZ Settings

This section describes how to control the camera’s Pan/Tilt/Zoom operation.

PTZ Settings
Go to Setup  PTZ Setup PTZ Settings.
Figure 5-1 PTZ Setup

PTZ Operations

Move: Click , , ,or to move the video image up, down, to the left or to the

right. To return to the home location, click .

36
 Configuring PTZ Settings

Zoom: Click to zoom out the video image, or click to zoom in the video image.
Pan Speed: Select a speed (-5 to 5) from the dropdown list.
Tilt Speed: Select a speed (-5 to 5) from the dropdown list.
Zoom Speed: Select a speed (-5 to 5) from the dropdown list.
Focus Speed: Select a speed (-5 to 5) from the dropdown list.
Go to: Select a preset location from the drop-down list, and the camera will move to the
selected position. You should set a preset location first. See Preset and Patrol Settings on
page 39.

Home Location Settings

SET CURRENT POSITION AS HOME: Click to set the current position as the home location.
RESTORE HOME POSITION TO DEFAULT: Click to restore the home position to default.

Patrol List
This patrol list displays the configured patrols. Note that only one patrol can be applied at a
time. To enable/disable an existing patrol, click ON/OFF.
Click ADD A RECORDED PATROL or ADD A PRESET PATROL below to create a recorded
patrol or a preset patrol.
Figure 5-2 Patrol List

Adding A Recorded Patrol

The recorded patrol allows you to record the process moving along interested points
(positions) in your surveillance area while the camera memorizes every Pan/Tilt/Zoom/Focus
commands you gave in the process. You can then save the process as a recorded patrol. Due
to the limitation on system memory, you can configure 4 recorded patrols, each with a length
of 2 minutes.

37
Honeywell 60 Series IP Camera Software Configuration Guide

Figure 5-3 Add A Recorded Patrol

To create a recorded patrol:

1. Enter a name for the patrol.
2. Enter a dwell time between runs.
3. Click on the screen or operate the PTZ panel to select a field of view as your start point.
4. Select the Pan/Tilt/Zoom/Focus speed.

5. Click to start scanning through your surveillance area by moving along and staying at

the points of your interest. Click again to stop the recording when you visited all of
your points of interest. Zoom and focus are also supported.

6. To review your recorded patrol, click . To stop the review, click . When you are
satisfied with the recording, click SAVE and then click CLOSE to leave the configuration
page. Note that if you start a new recording without saving the previous one, the previous
recording will be abandoned.
7. To implement the patrol schedule, click ON for the patrol in the patrol list (see Patrol List
on page 37), and then click on the PTZ panel (see Figure 3-9) in the main page.

38
 Configuring PTZ Settings

Adding a Preset Patrol

Figure 5-4 Add A Preset Patrol

1. Enter a name for the preset patrol.

2. Select a patrol speed form the dropdown list.
3. Select a patrol direction from the dropdown list.
4. Click on the screen or operate the PTZ panel to adjust the shooting area to the desired
position.
5. Select the Pan/Tilt/Zoom/Focus speed.
6. Enter a name for the preset. Click ADD and the preset will be listed in the User preset
locations list. Repeat the above steps to add more preset locations. To remove a preset,
select it and click REMOVE.

7. Select the preset locations in the preset locations list, and click .
8. The selected preset locations will be displayed in the Patrol locations list. The default
dwell time is 5 seconds. Set the Dwelling time for the preset location during an auto
patrol.

39
Honeywell 60 Series IP Camera Software Configuration Guide

Figure 5-5 Set a Patrol

9. To delete a preset location from the Patrol locations list on the right pane, select the
check box of target patrol locations and click REMOVE.

10. To rearrange the patrol order, select a location and click or .

11. Select patrol locations you want to use in the list and click SAVE to enable the patrol
settings.
12. To implement the patrol schedule, click ON for the patrol in the patrol list (see Patrol List
on page 37), and then click on the PTZ panel (see Figure 3-9) in the main page.

Misc Settings
Figure 5-6 Misc Settings

PTZ control panel operation mode: This determines how your mouse and PTZ control panel
works on a live view window.
• Continuous move: It allows your screen control action to continue as long as you click
and hold down the left mouse button. For example, if you click on the left button on the
PTZ control panel, the camera's view should continuously rotate to the left until you
release the button. The same applies to arrow keys, Zoom, and Focus buttons on the PTZ
panel.
• Click to move: One action taken effect with one click.
Focus mode: Select a focus mode from the dropdown list. Auto, One-time focus, Spotlight
avoidance and Manual can be selected.

40
 Configuring PTZ Settings

• Auto: Select this mode and the camera will auto focus all the time, except the presets with
fixed focus. This mode is applicable to most scenarios.
• One-time focus: Select this mode and the camera will auto focus once after the PTZ
control is stopped.
• Spotlight avoidance: Select this mode and the camera will perform the focus in
accordance with the spot light environment at night.
• Manual: Select this mode to manually adjust the focus.
Enable digital zoom: Select the checkbox and you will be able to zoom in on an image by up
to 360X magnification with the combination of the 30x mechanical zoom and another 12X
digital zoom.
Zoom factor display: Select the checkbox to display zoom factor on the video image.
Apply previous action if the camera idles for 5 seconds: From the dropdown list, select an
action to be taken when the camera sits idle for a configurable period time. For example, you
can let camera resume a patrol tour. The resumed patrol will continue from the last preset
position. You may also let the camera return to the home position. The idle state does not
include the situations when the camera is performing pan or patrol action.
• Enable auto tracking: Select it and the camera will perform auto tracking. It will return
home position before auto tracking.
• Return to home position: Select it and the camera will return to home position.
• Start to pan: Select it and the camera will start to pan.
• Start to patrol: Select it and the camera will start to patrol.

Calibrate
Go to Setup  PTZ Setup  Calibrate.
This function re-calibrates the home position to the default center to recover any
displacement caused by external forces. Please note that there is no confirm message after
using the function, and the calibration immediately takes place. If, after a long use, a user
finds it is difficult to move camera’s field of view to a specific point, use this function to
restore the camera’s original coordinates in pan and tilt motions.

41
Honeywell 60 Series IP Camera Software Configuration Guide

Figure 5-7 Calibrate

Auto Tracking
You can modify the minimum object size as the triggering factor while performing the Auto
Tracking function. You can move the camera view to an area of your interest, estimate, and
define the possible size of objects. For example, you can designate the object size such as
that of a human trespasser. The silhouette of the tresspasser must be larger than the whole of
the object size square box. The minimum object size is 30x30 pixels within a 320x420 view
window.
Go to Setup  PTZ Setup  Auto Tracking.
Figure 5-8 Auto Tracking

Sensitivity: Drag the slider bar horizontally to adjust the sensitivity of the tracking function.
Modify minimum object size: Click it and the grey rectangle on the video will be turn white.
You can drag the rectangle and move it to the target place. You can also resize the rectangle
by adjusting the width and length.

42
 Configuring PTZ Settings

After all settings are completed, click SAVE.

On the PTZ panel of live view, click on the PTZ panel (see Figure 3-9) in the main page.
If there is an intruder, the camera will follow and track the intruder. To stop the auto tracking,
click any buttons on the PTZ panel, or a mouse click takes place on a view window.
You can choose to perform other functions, such as pan or patrol, simply by clicking their
buttons on the PTZ panel while the camera is performing the auto tracking function.

43
Honeywell 60 Series IP Camera Software Configuration Guide

6 Configuring Network Settings

This chapter contains the following sections:
• Configuring Network General Settings, page 44
• Configuring Streaming Protocols, page 47
• Configuring DDNS Settings, page 50
• Configuring QoS Settings, page 50
• Configuring SNMP Settings, page 52
• Configuring HTTPS Settings, page 54
• Configuring IEEE 802.1X Settings, page 55

Configuring Network General Settings

This section describes how to configure a wired network connection for the camera.
Figure 6-1 Network Type

LAN
Get IP address automatically: Select this option to obtain an available dynamic IP address
assigned by the DHCP server each time the camera is connected to the LAN.
Use fixed IP address: Select this option to manually assign a static IP address to the camera.
• IP address:

44
 Configuring Network Settings

1. You can make use of Unified Tool in the software CD to easily set up the camera on
LAN. See Accessing the Camera on page 3.
2. Enter the Static IP, Subnet mask, Default router, and Primary DNS provided by your
ISP or network administrator.
• Subnet mask: This is used to determine if the destination is in the same subnet. The
default value is “255.255.255.0”.
• Default router: This is the gateway used to forward frames to destinations in a different
subnet. Invalid router setting will disable the transmission to destinations across different
subnets.
• Primary DNS: The primary domain name server that translates hostnames into IP
addresses.
• Secondary DNS: Secondary domain name server that backups the Primary DNS.
• Primary WINS server: The primary WINS server that maintains the database of computer
names and IP addresses.
• Secondary WINS server: The secondary WINS server that maintains the database of
computer names and IP addresses.
Enable UPnP presentation: Select this option to enable UPnP presentation for your camera
so that whenever a camera is presented to the LAN, the shortcuts to connected cameras will
be listed in Network and Sharing Center. You can click the shortcut to link to the web browser.

To utilize this feature, make sure the UPnP component is installed on

Note
your computer.

Enable UPnP port forwarding: To access the camera from the Internet, select this option to
allow the camera to open ports automatically on the router so that video streams can be sent
out from a LAN. To utilize of this feature, make sure that your router supports UPnP and it is
activated.
Enabling UPnP in Windows
The UPnP protocol is used to detect network devices with clients running Windows.
The camera can be detected by Windows' built-in network browser.
To enable UPnP in Windows 10:
1. Go to Start Control Panel Network and Sharing Center.
2. On the left pane, click Change advanced sharing settings.
3. On your current network profile, in the Network discovery area, click Turn on network
discovery, and then click Save changes.

Enable IPv6
Select this option and click SAVE to enable IPv6 settings.

45
Honeywell 60 Series IP Camera Software Configuration Guide

Figure 6-2 Enable IPv6

When IPv6 is enabled, by default, the network camera will listen to router advertisements and
be assigned with a link-local IPv6 address accordingly.
IPv6 Information: Click to obtain the IPv6 information as shown below.
Figure 6-3 IPv6 Information

If your IPv6 settings are successful, the IPv6 address list will be listed in the pop-up window.
Follow the steps below to link to an IPv6 address:
1. Open your web browser.
2. Enter the link-global or link-local IPv6 address in the address bar of your web browser.
3. The format should be: http://[2001:0c08:2500:0002:0202:d1ff:fe04:65f4]/
4. Press Enter on the keyboard or click Refresh button to refresh the webpage.
Manually setup the IP address: Select this option to manually set up IPv6 settings if your
network environment does not have DHCPv6 server and router advertisements-enabled
routers. If you check this item, the following blanks will be displayed for you to enter the
corresponding information:

46
 Configuring Network Settings

Figure 6-4 Manually setup IP Address

Configuring Streaming Protocols

Go to SetupNetwork SetupStreaming Protocols.
Figure 6-5 Streaming Protocols - HTTP

To utilize HTTP authentication, make sure that you have set a password for the camera first.
For more information, see Configuring User Accounts Settings on page 82.
Authentication (digest): User credentials are encrypted with MD5 algorithm which provide
better protection against unauthorized accesses.
HTTP port: By default, the HTTP port is set to 80. It can also be assigned to another port
number between 1025 and 65535.

47
Honeywell 60 Series IP Camera Software Configuration Guide

Access name for main stream/sub stream/third stream: The camera supports multiple
streams simultaneously. The access name is used to identify different video streams. You can
set up the video quality of linked streams. For more information, see Video Stream on page 22.
Figure 6-6 Streaming Protocols – RTSP

To utilize RTSP streaming authentication, make sure that you have set a password for
controlling the access to video stream first. For more information, see Configuring User
Accounts Settings on page 82.
Authentication (digest): User credentials are encrypted with MD5 algorithm which provides
better protection against unauthorized access.
Access name for main stream/sub stream/third stream: The camera supports multiple
streams simultaneously. The access name is used to differentiate the streaming source.
If you want to use an RTSP player to access the camera, you have to set the video mode to
H.264 or H.265 and use the following RTSP URL command to request transmission of the
streaming data.
rtsp://<ip address>:<rtsp port>/<access name for stream 1 to 3>
For example, when the access name for stream 1 is set to live.sdp:
1. Launch an RTSP player.
2. Choose File  Open URL. A URL dialog box will pop up.
3. Type the above URL command in the text box.
4. The live video will be displayed in your player.
RTSP port /RTP port for video / RTCP port for video:
• RTSP (Real-Time Streaming Protocol) controls the delivery of streaming media. By
default, the RTSP port number is set to 554.
• The RTP (Real-time Transport Protocol) is used to deliver video data to the clients. By
default, the RTP port for video is set to 5556.

48
 Configuring Network Settings

• The RTCP (Real-time Transport Control Protocol) allows the camera to transmit the data
by monitoring the Internet traffic volume. By default, the RTCP port for video is set to
5557.
The ports can be changed to values between 1025 and 65535. The RTP port must be an even
number and the RTCP port is the RTP port number plus one, and thus is always an odd
number. When the RTP port changes, the RTCP port will change accordingly.
RTP port for metadata: By default, the RTP port for metadata is set to 6556.
RTCP port for metadata: By default, the RTCP port for video is set to 6557.
Multicast settings for streams: Click to display the detailed configuration information.
Figure 6-7 Multicast Settings

Always multicast: Check to enable multicast for video streams.

Multicast group address: Enter the Multicast group address.
Multicast video port/Multicast RTCP video port: The ports can be changed to values
between 1025 and 65535. The multicast video port must be an even number and the
multicast RTCP video port number is the multicast video port number plus one, and thus is
always odd. When the multicast video port changes, the multicast RTCP video port will
change accordingly.
Multicast metadata port/Multicast RTCP metadata port: The ports can be changed to
values between 1025 and 65535. The multicast metadata port must be an even number and
the multicast RTCP metadata port number is the multicast metadata port number plus one,
and thus is always odd. When the multicast metadata port changes, the multicast RTCP
metadata port will change accordingly.
Multicast TTL [1~255]: The multicast TTL (Time To Live) is the value that tells the router the
range a packet can be forwarded. The default value is 15.

49
Honeywell 60 Series IP Camera Software Configuration Guide

Configuring DDNS Settings

Go to SetupNetwork SetupDDNS.
This section describes how to configure the dynamic domain name service for the camera.
DDNS is a service that allows your camera, especially when assigned with a dynamic IP
address, to have a fixed host and domain name.
Figure 6-8 DDNS

Enable DDNS: Check to enable the DDNS setting.

Before utilizing this function, apply for a dynamic domain account

first and then access the system through that domain. Refer to the
Note following link to apply for a dynamic domain account:
http://www.dyndns.com/

Provider: Select a DDNS provider from the dropdown list.

Camera name: Enter the camera name of your dynamic domain account.
User name: Enter the user name of your dynamic domain account.
Password: Enter the password of your dynamic domain account.

Configuring QoS Settings

Go to Setup Network Setup Qos.
Quality of Service (QoS) is a network security mechanism. It fixes problems with network
delays and jams. For network service, the quality of service includes the transmission
bandwidth, delay, and packet loss, for example. Through QoS, you can guarantee the
transmission bandwidth, reduce the delay, reduce the loss of data packets, and enhance the
transmission quality with packet prioritization.
To utilize QoS in a network environment, the following requirements must be met:
• All network switches and routers in the network must include support for QoS.

50
 Configuring Network Settings

• The network video devices used in the network must be QoS-enabled.

CoS
CoS refers to Class of Service. It indicates the frame priority level from 0 (lowest) to 7
(highest). The priority is set up on the network switches, which then use different queuing
disciplines to forward the packets.
Figure 6-9 Cos

Enter the VLAN ID of your switch (0~4095) and choose the priority for each application (0~7).
If you assign Video the highest level, the switch will handle video packets first.

• A VLAN Switch (802.1p) is required. Web browsing may fail if

the CoS setting is incorrect.
• The Class of Service technologies do not guarantee a level of
service in terms of bandwidth and delivery time; they offer a
Note "best-effort." Users can think of CoS as "coarsely-grained"
traffic control and QoS as "finely-grained" traffic control.
• Although CoS is simple to manage, it lacks scalability and
does not offer end-to-end guarantees since it is based on L2
protocol.

QoS/DSCP
Routers at each network node classify packets according to their DSCP ((Differentiated
Services Codepoint) value and give them a particular forwarding treatment; for example, how
much bandwidth to reserve for it.

51
Honeywell 60 Series IP Camera Software Configuration Guide

Figure 6-10 QoS/DSCP

Specify the DSCP value for each application (0~63).

Configuring SNMP Settings

Go to Setup Network Setup  SNMP.
SNMP (Simple Network Management Protocol) is a protocol for collecting, organizing, and
exchanging management information between managed devices on a network.
The SNMP consists of the following three key components:
• Manager: Network-management station (NMS), a server which executes applications that
monitor and control managed devices.
• Agent: A network-management software module on a managed device which transfers the
status of managed devices to the NMS.
• Managed device: A network node on a managed network. For example: routers, switches,
bridges, hubs, computer hosts, printers, IP telephones, network cameras, web server, and
database.
Before configuring SNMP settings on the page, enable your NMS first.

52
 Configuring Network Settings

Figure 6-11 SNMP Configurations

Enable SNMPv1, SNMPv2c: Check to enable SNMPv1, SNMPv2c.

Enter the names of Read/Write community and Read Only community according to your NMS
settings.
Enable SNMPv3: Check to enable SNMPv3 which contains cryptographic security, a higher
security level.
• Security name: Choose Read/Write or Read Only and enter the community name
according to your NMS settings.
• Authentication type: Select MD5 or SHA as the authentication method.
• Authentication password: Enter the password for authentication (at least 8 characters).
• Encryption password: Enter a password for encryption (at least 8 characters).

53
Honeywell 60 Series IP Camera Software Configuration Guide

Configuring HTTPS Settings

Go to Setup Network Setup  HTTPS.

HTTPS
Go to Setup Network Setup  HTTPS HTTPS.
This section explains how to enable authentication and encrypted communication. It helps
protect streaming data transmission over the Internet on higher security level.
Figure 6-12 HTTP

HTTP & HTTPS: Select it and the web browser can be accessed via HTTP or HTTPS.
HTTPS only: Select it and the web browser can only be accessed via HTTPS with higher
security level. This option is selected by default.

Certificate Request
Go to Setup Network Setup  HTTPS Certificate Request.
You can fill in certificate information and the certificate request file can be exported to the
certificate issuing authority for signing and then being imported to camera.
Figure 6-13 Certificate Request

Enter the information of Country, State or province, Locality, Organization and Organization
unit. Click CREATE.
Click EXPORT to export the certificate request to your local computer. After you get the
signing certificate from the certificate issuing authority, click CHOOSE FILE and UPLOAD to
import it to the camera. The imported certificate will replace the original self-signed certificate
of the camera.

54
 Configuring Network Settings

After the certificate file is uploaded successfully, if you want to remove the certificate, click
REMOVE.

Upload files
Go to Setup Network Setup  HTTPS Upload files.
You can import the certificate from third party here.
Figure 6-14 Upload files

To import the certificate from third party:

1. In the Certificate field, click CHOOSE FILE to select a certificate file you have already
applied from 3rd party or CA domain.
2. In the Key field, click CHOOSE FILE to select a certificate key you have already applied
from 3rd party or CA domain.
3. Click UPLOAD and reboot camera.
After the certificate file is uploaded successfully, if you want to remove the certificate, click
REMOVE.

• Supported certificate type: HTTPS protocol.

Note • Supported certificate file format: *.cert format.
• Supported Key format: PEM format.

Configuring IEEE 802.1X Settings

Go to Setup Network Setup 802.1X.
IEEE802.1X is the access control and authentication protocol for local and metropolitan area
networks. It uses a port-based network access control protocol to restrict unauthorized user
and/or device access to the LAN. The network devices, intermediary switch/access point/hub,
and RADIUS server must support and enable 802.1x settings.
To configure IEEE 802.1x settings:
1. Before connecting the camera to the protected network with 802.1x, apply a digital
certificate from a Certificate Authority (i.e., your network administrator) which can be
validated by a RADIUS server.
2. Connect the camera to a PC or notebook outside of the protected LAN. Open the
configuration page of the camera as shown below.

55
Honeywell 60 Series IP Camera Software Configuration Guide

Figure 6-15 IEEE 802.1X Configurations – EAP-PEAP

Figure 6-16 IEEE 802.1X Configurations – EAP-TLS

Select EAP-PEAP or EAP-TLS as the EAP method. Enter your ID and password issued by
the CA, and then upload related certificate(s).
3. When all settings are complete, move the camera to the protected LAN by connecting it to
an 802.1x enabled switch. The devices will then start the authentication automatically.

56
 Configuring Video Analytics

7 Configuring Video Analytics

This chapter contains the following sections:
• Configuring Motion Detection Settings, page 57
• Configuring Alarm In and Alarm Out, page 59
• Configuring Tampering Detection Settings, page 58
• Configuring Event Settings, page 59
• Package Management, page 67

Configuring Motion Detection Settings

Go to Setup Video Analytics  Motion Detection.
Two sets of motion detection settings are available:
• In Normal Light Mode tab, configure normal situations for motion detection settings.
• In Profile Mode tab, configure special situations for motion detection settings.
• Night Mode: Check Enable to apply these settings at and select this mode to apply
the settings at night.
• Schedule Mode: Check Enable to apply these settings at and select this mode to
apply the settings at a specific period. Enter the time manually in the field.

Motion Detection
The Motion Detection detects motions in customized windows. If a motion is detected, the
frame of the customized window will become flashing red.
To enable motion detection:
1. Click NEW to add a new motion detection window.
2. In the Window Name text box, enter a name for the motion detection window.
a. Draw a detection area by clicking four corner points on the target area. You can
change the shape of the detection area by dragging the corner points.
b. Drag the object size slider to change the minimum size of item to trigger an alarm. An
object size box will appear in the center of screen for your reference (in semi-
transparent red). An intruding object must be larger than the Object size to trigger an
alarm. Change the object size according to the live view.

c. To delete a window, click on the right of the window name.

3. Define the sensitivity to moving objects by moving the Sensitivity slider. A high sensitivity
is prone to produce false alarms such as the fast changes of light (such as day/night

57
Honeywell 60 Series IP Camera Software Configuration Guide

mode switch, turning lights on/off). A movement must persist longer than 0.3 second for
the motion to be detected.
4. Click SAVE to enable the settings.
5. Select Enable motion detection to enable this function.
Figure 7-1 Configuring Motion Detection Settings

Configuring Tampering Detection Settings

Go to Setup Video Analytics  Tampering Detection.
This section explains how to configure camera tamper detection settings. With tamper
detection, the camera is capable of detecting incidents such as redirection, blocking or
defocusing, or even spray paint.
Figure 7-2 Tampering Detection Configurations

Tampering detection: Check to enable tampering detection.

Image too dark detection: Check to enable image too dark detection. Too dark can be a cover
on the camera or a spraying paint on the camera.
Image too bright detection: Check to enable image too bright detection. Too bright can be a
flash light shining to the camera.
Image too blurry detection: Check to enable image too blurry detection. To blurry can be the
result of strong interference on the camera, such as EMI interference.

58
 Configuring Video Analytics

Trigger duration: It specifies a set of time before the tampering is considered as a real alarm.
This helps avoid false alarms by short-lived changes.
Trigger threshold: It determines how sensitive the tamper detection setting is. The lower the
threshold value, the easier the detection is triggered.
You can configure Tampering Detection as a trigger element to the proactive event
configurations in Video Analytics  Event settings  Trigger. For example, when the
camera is tampered with, camera can be configured to send the pre- and post-event video
clips to a networked storage device. For more information, see Trigger on page 61.

Configuring Alarm In and Alarm Out

Go to Setup Video Analytics  Alarm In and Alarm Out.
Figure 7-3 Alarm In and Alarm Out

Alarm in: Select High or Low to define normal status for the alarm input. Connect an alarm
input from a sensor device to the camera, the camera will report the current signal status. You
may then configure the Normal status (non-trigger status) as High or Low.
Alarm out: Select High or Low to define normal status for the alarm output. Connect an output
line to an external device, the camera will report the current signal status. You may then
configure the Normal status (non-trigger status) as High or Low.
Set up the event source as Alarm In on Event Settings  Trigger. For detailed information,
see Trigger on page 61.

Configuring Event Settings

Go to Setup Video Analytics  Event Settings.
This section describes how to configure the camera to respond to particular situations
(event). A typical application is that when a motion is detected, the camera sends buffered
images to an e-mail address as notifications. Click Help, there is an illustration shown in the
pop-up window explaining that an event can be triggered by many sources, such as motion

59
Honeywell 60 Series IP Camera Software Configuration Guide

detection or external alarm input devices. When an event is triggered, you can specify what
type of action that will be performed. You can configure the camera to send snapshots or
videos to your email address.
Figure 7-4 Event Settings

Event
In the Event tab, click ADD to open the event settings window. Here you can arrange three
elements -- Schedule, Trigger, and Action to set an event. A total of 3 event settings can be
configured.

60
 Configuring Video Analytics

Figure 7-5 Event

• Event name: Enter a name for the event setting.

• Enable this event: Check to enable the event setting.
• Priority: Select the relative importance of this event (High, Normal, or Low). Events with a
higher priority setting will be executed first.
• Detect next motion detection or digital input after x seconds: Enter the duration in
seconds to pause motion detection after a motion is detected. This can prevent event-
related actions to take place too frequently.

Schedule
Specify the period of time during which the event trigger will take effect. Select the days of a
week and the time in a day (in 24-hr time format) for the event triggering schedule. For
example, you may prefer an event to be triggered only during the off-office hours.

Trigger
This is the cause or stimulus which defines when to trigger the camera.
There are several choices of trigger sources as shown below:

61
Honeywell 60 Series IP Camera Software Configuration Guide

Figure 7-6 Trigger Sources

Video motion detection

This option makes use of the built-in motion detection mechanism as a trigger source. To
enable this function, you need to configure a Motion Detection Window first. For more
information, see Configuring Motion Detection Settings on page 57.
Periodically
This option allows the camera to trigger periodically for every other defined minute. Up to 999
minutes can be set.
Alarm input
This option allows the Network Camera to use an external digital input device or sensor as a
trigger source. Depending on your application, there are many choices of digital input devices
on the market which helps to detect changes in temperature, vibration, sound, and light, etc.
System boot
This option triggers the camera when the power to the camera is disconnected and re-
connected.
Recording notification
This option allows the camera to trigger when the recording disk is full or when recording
starts to overwrite older data.
Camera tampering detection
This option allows the camera to trigger when the camera detects that is being tampered with.
To enable this function, you need to configure the Tampering Detection option first, see
Configuring Tampering Detection Settings on page 58.

Action
It defines the actions to be performed by the camera when a trigger is activated.

62
 Configuring Video Analytics

Figure 7-7 Action

Trigger digital input for x seconds: Select this option to trigger alarm output for x seconds.
Enter a value in the textbox.
Backup media if the network is disconnected:
Select this option to backup media files to SD card if the network is disconnected. This
function will apply after you configure the Email and HTTP. For example, if a snapshot is
supposed to be delivered to an Email receiver, in the event of network failure, the snapshot will
be saved in the SD card.
Trigger auto tracking: Select this option to trigger auto tracking. This function is applicable to
HC60WZ2E30.
Move to preset location: Select this option to trigger the camera to preset location. Select a
preset location from the dropdown list. You should configure preset locations first, see Adding
a Preset Patrol on page 39. This function is applicable to HC60WZ2E30.
SD Test: Click to test your SD card. The system will display a message indicating the result as
a success or a failure. If you want to use your SD card for local storage, format it before use.
For more information, see SD Card Format on page 70 .

Add Server

Before adding server or adding media, click SAVE EVENT to avoid

Note
that the event will be lost when adding server or adding media.

Click Add server to open the server setting window. You can specify where the notification
messages are sent to when a trigger is activated. A total of 5 server settings can be
configured.
There are the following server types available: Email and HTTP. Select the item to display the
detailed configuration options. You can configure either one or all of them.

63
Honeywell 60 Series IP Camera Software Configuration Guide

Figure 7-8 Add Server

Server type - Email

Select to send the media files via email when a trigger is activated.
• Server name: Enter a name for the server setting.
• Sender email address: Enter the email address of the sender.
• Recipient email address: Enter the email address of the recipient.
• Server address: Enter the domain name or IP address of the email server.
• User name: Enter the user name of the email account if necessary.
• Password: Enter the password of the email account if necessary.
• Server port: The default mail server port is set to 25. You can also manually set another
port.
• If your SMTP server requires a secure connection (SSL), select This server requires a
secure connection (SSL).
• To verify if the email settings are correctly configured, click Test. The result will be shown
in a pop-up window. If successful, you will also receive an email indicating the result.
Click SAVE SERVER to enable the settings.
After you configure the first event server, the new event server will be automatically display on
the Server list. If you wish to add other server options, click Add server.
Server type - HTTP
Select to send the media files to an HTTP server when a trigger is activated.
Figure 7-9 Server type – HTTP

64
 Configuring Video Analytics

• Server name: Enter a name for the server setting.

• URL: Enter the URL of the HTTP server.
• User name: Enter the user name if necessary.
• Password: Enter the password if necessary.
To verify if the HTTP settings are correctly configured, click TEST. The result will be shown in a
pop-up window. If successful, you will receive a test.txt file on the HTTP server.
Click SAVE SERVER to enable the settings.

Add Media
Click Add media to open the media setting window. You can specify the type of media that will
be sent when a trigger is activated. A total of 5 media settings can be configured. There are
three choices of media types available: Snapshot, Video Clip, and System log. Select the item
to display the detailed configuration options. You can configure either one or all of them.
Figure 7-10 Add Media

Media type – Snapshot

Select to send snapshots when a trigger is activated.
• Media name: Enter a name for the media setting.
• Source: Select to take snapshots from any of the video streams.
• Send pre-event images:
The camera has a buffer to temporarily hold data up to a certain limit. Enter a number to
decide how many images to capture before a trigger is activated. Up to 7 images can be
generated.
• Send post-event images:
Enter a number to decide how many images to capture after a trigger is activated. Up to 7
images can be generated.
For example, if both the Send pre-event images and Send post-event images are set to 7,
a total of 15 images can be generated after a trigger is activated.
• File name prefix
Enter the text that will be appended to the front of the file name.

65
Honeywell 60 Series IP Camera Software Configuration Guide

• Add date and time suffix to the file name

Select this option to add a date/time suffix to the file name.
Click SAVE MEDIA to enable the settings. The new media server will be automatically
displayed in the Media list. If you wish to add more media options, click ADD MEDIA.
Media type - Video clip
Select to send video clips when a trigger is activated.
• Media name: Enter a name for the media setting.
• Source: Select a video stream as the source of video clip.
• Pre-event recording
The camera has a buffer to temporarily hold data up to a certain limit. Enter a number to
decide the duration of recording before a trigger is activated. Up to 9 seconds can be set.
• Maximum duration
Specify the maximum recording duration in seconds. The duration can be up to 10
seconds.
For example, if pre-event recording is set to five seconds and the maximum duration is set
to ten seconds, the camera continues to record for another 4 seconds after a trigger is
activated.
• Maximum file size
Specify the maximum file size allowed. Some users may need to stitch the video clips
together when searching and packing up forensic evidence.
• File name prefix
Enter the text that will be appended to the front of the file name.
Click SAVE MEDIA to enable the settings.
Media type - System log
Select to send a system log when a trigger is activated.
Click SAVE MEDIA to enable the settings, and then click CLOSE to exit the page.
In the Event settings tab, the Servers and Medias you configured will be listed. Make sure the
Event Status is set to ON, in order to enable the event triggering action.
When completed, click SAVE EVENT to enable the settings and click CLOSE to exit Event
Settings page. The new Event / Server settings / Media will be displayed in the event drop-
down list on the Event setting page.
See the example of the Event setting page below:

66
 Configuring Video Analytics

Figure 7-11 Event Settings Examples

When the Event Status is ON, the event configuration above is triggered by motion detection,
the camera will automatically send snapshots via e-mail.
If you want to stop the event trigger, you can click on the ON button to turn it to OFF status or
click DELETE to remove the event setting.
To remove a server setting from the list, select a server name and click DELETE.
You can only delete a server setting when it is not applied in an existing event setting.
To remove a media setting from the list, select a media name and click DELETE.
You can only delete a media setting when it is not applied in an existing event setting.

Package Management
Go to Setup Video Analytics  Package Management.
Figure 7-12 Package Management

67
Honeywell 60 Series IP Camera Software Configuration Guide

The Resource Status shows the information of CPU loading, total size of internal storage, total
size of memory and total size of SD card. If the total size of internal storage is not enough,
click CLEANUP to clean the internal storage.
Click Deep Learning VCA, you can enter the interface of Video Analytics for intelligent video
applications such as face detection, intrusion detection, loitering detection, missing object
detection, unattended object detection, and line crossing detection. For how to configure the
VA settings, refer to the user guide of Video Analytics.
To start running the Deep Learning VCA package, click START.
To stop running the Deep Learning VCA package, click STOP.

To delete the Deep Learning VCA package, click .

If you want to apply the Deep Learning VCA settings at a specific period, click SCHEDULE,
enter the time manually in the field and click SAVE.

68
 Configuring Storage Settings

8 Configuring Storage Settings

This chapter contains the following sections:
• SD Card Management, page 69
• Content Management, page 71
• Recording Settings, page 73

SD Card Management
Go to Setup Storage Setup SD Card Management.
This section describes how to manage the local storage on the camera. Here you can view SD
card status, and implement SD card control.
See the following table for compatible SD Card.
Table 8-1 Compatible SD Card
SD Card Brand Model Size
Sandisk microSDXC UHS-I Card 256 GB
Toshiba microSDXC UHS-I Card 256 GB
Samsung microSDXC UHS-I Card 256 GB
Toshiba microSDXC UHS-I Card 128 GB
Sony Sony Smart SD micro SDXC 64G 64 GB
Sony Ultra microSDHC UHS-I 48MB/s 64 GB
Sandisk microSDHC UHS-I Card 32 GB
Transcend Transcend microSDHC 4G Class4 4 GB

69
Honeywell 60 Series IP Camera Software Configuration Guide

• It is recommended to turn OFF the recording activity before

you remove an SD card from the camera.
• The lifespan of an SD card is limited. Regular replacement of
the SD card can be necessary.
• Camera file system takes up several megabytes of memory
space. The storage space cannot be used for recording.
Note • Using an SD card that already contains data recorded by
another device should not be used in this camera.
• Do not modify or change the folder names in the SD card. That
may result in camera malfunctions.
• If you want to use the SD card in another camera, format the
SD card in another camera first. For how to format the SD card,
see SD Card Format on page 70.

SD Card Status
This tab shows the status and reserved space of your SD card. Remember to format the SD
card when using it for the first time, see SD Card Format on page 70.
Figure 8-1 No SD Card

Figure 8-2 SD Card Onboard

SD Card Format
Figure 8-3 SD Card Format

To format the SD Card, click FORMAT.

70
 Configuring Storage Settings

SD Card Control
Figure 8-4 SD Card Control

Minimum reserved storage space: Enter a percentage for minimum storage space you want
to reserve.
• Enable cyclic storage: Check to enable cyclic recording. When the maximum capacity is
reached, the oldest file will be overwritten by the latest one.
• Enable automatic disk cleanup: Check to enable automatic disk cleanup. Enter the
number of days you wish to retain a file. For example, if you enter “7 days”, the recorded
files will be stored on the SD card for 7 days.
Click SAVE to enable your settings.

Content Management
Go to Setup Storage Setup Content Management.
This section describes how to manage the content of recorded videos on the camera. Here
you can search and view the records and view the searched results.

Searching and Viewing the Records

This tab allows the user to set up search criteria for recorded data. If you do not select any
criteria and click SEARCH, all recorded data will be listed in the Search Results tab.

71
Honeywell 60 Series IP Camera Software Configuration Guide

Figure 8-5 Search

• Trigger Type: Select one or more trigger types.

• Media Type: Select a media type (Video clip, snapshot or text).
• Time: Manually enter the time range you want to search for contents created at a specific
point in time.
Click SEARCH and the recorded data corresponding to the search criteria will be listed in
Search Results tab.

Search Results
The following is an example of search results. To sort the search results, click each column
header.
Figure 8-6 Search Results

• Play: Click on a search result and a Play window will be displayed for immediate review of
the selected file.

72
 Configuring Storage Settings

Figure 8-7 Play Search Result

• Download: Click on a search result and click DOWNLOAD, and a file download window will
pop up for you to save the file. You can play the video clip by VLC player.
• JPEGs to AVI: This functions only applies to “JPEG” format files such as snapshots. You
can select several snapshots from the list, then click JPEGS TO AVI. Those snapshots will
be converted into an AVI file.
• Lock/Unlock: Select the checkbox in front of a desired search result, then click
LOCK/UNLOCK. The selected items will become Locked, which will not be deleted during
cyclic recording. You can click again to unlock the selections.
• Remove: Select the desired search results, then click REMOVE to delete the files.

Recording Settings
Go to Setup Storage Setup Recording Settings.
This section describes how to configure the recording settings for the camera.
Figure 8-8 Recording Settings

SD Test: Insert the SD card and click here to test.

Format your SD card via the camera’s web console when using it
Note for the first time. For more information, see SD Card Status on page
70.

73
Honeywell 60 Series IP Camera Software Configuration Guide

Adding a Recording Setting

Click ADD as shown in Figure 8-8 to open the recording setting window. On this page, you can
define the adaptive recording, recording source, recording schedule, and recording capacity.
A total of 2 recording settings can be configured.
Figure 8-9 Recording Settings Details

• Recording name: Enter a name for the recording setting.

• Enable this recording: Select this option to enable video recording.
• With adaptive recording:
Select this option will activate the frame rate control according to alarm trigger.
The frame control means that when there is a triggered alarm, the frame rate will raise up
to the value you’ve configured on the Video quality page. For more information, see Smart
codec configuration on page 24.
If you enable adaptive recording on a camera, only when an event is triggered on camera
will the server record the full frame rate streaming data; otherwise, it will only request the I
frame data during normal monitoring, thus effectively saves bandwidths and storage
space.

74
 Configuring Storage Settings

• To enable adaptive recording, make sure you’ve set up the

trigger source such as Motion Detection or Manual Trigger. For
more information, see Configuring Event Settings on page 59.
• When there is no alarm trigger:
Note • JPEG mode: record 1 frame per second.
• H.264 mode: record the I frame only.
• When the I frame period is >1s on Video settings page, firmware
will force decreasing the I frame period to 1s when adaptive
recording is enabled.

• Priority: Select the relative importance of this recording (High, Normal, or Low). Recording
with a higher priority setting will be executed first.
• Source: Select a video stream as the recording source.

To enable recording notification, configure Event settings first, see

Note
Configuring Event Settings on page 59.

Setting up a Recording
To set up a recording:
1. Select a trigger source.
Schedule: The server will start to record files on the local storage.
Network failure: When network fail, the server will start to record files on the local storage
(SD card).
2. Set a destination (SD) for the recorded video files.
• Manually assign the Maximum duration and the Maximum file size for each recording
footage.
• File name prefix: Enter the text that will be appended to the front of the file name.
If you want to enable recording notification, click Event to configure event triggering settings.
For more information, see Configuring Event Settings on page 59.
When completed, select Enable this recording. Click SAVE to enable the setting and click
CLOSE to exit this page. When the system begins recording, it will send the recorded files to
the network storage. The new recording name will be displayed on the recording settings page
as shown below.
To remove a recording setting from the page, click DELETE.

75
Honeywell 60 Series IP Camera Software Configuration Guide

Figure 8-10 Recording 1

• Click Recording 1 (Name): Opens the Recording Settings page to modify.

• Click ON (Status): The Status will become OFF and stop recording.
• Click SD (Destination): Opens the file list of recordings.

76
 Configuring System Settings

9 Configuring System Settings

This chapter contains the following sections:
• Configuring System General Settings, page 77
• Configuring Maintenance Settings, page 78
• Configuring User Accounts Settings, page 82
• Configuring Access List Settings, page 83

Configuring System General Settings

Go to Setup System Setup General Settings.
This section explains how to configure the basic settings for the camera, such as the host
name and system time.
Figure 9-1 Configuring System General Settings

Camera Name: Enter a name for the camera. The text will be displayed at the top of the main
page.
Turn off the LED indicators: If you do not want others to notice the network camera is in
operation, you can select this option to turn off the LED indicators.

77
Honeywell 60 Series IP Camera Software Configuration Guide

Time zone: Select the appropriate time zone from the dropdown list. If you want to upload
Daylight Savings Time rules, see Configuring Maintenance Settings on page 78 .
Keep current date and time: Select this option to preserve the current date and time of the
camera. The camera’s internal real-time clock maintains the date and time even when the
power of the system is turned off.
Synchronize with computer time: Select this option to synchronize the date and time of the
camera with the local computer. The read-only date and time of the PC is displayed as
updated.
Manual: The administrator can enter the date and time manually. The date and time format
are [yyyy/mm/dd] and [hh:mm:ss].
Automatic: The Network Time Protocol is a protocol which synchronizes computer clocks by
periodically querying an NTP Server.
• NTP server: Assign the IP address or domain name of the time-server. Leaving the text box
blank connects the camera to the default time servers. The precondition is that the
camera must have the access to the Internet.
• Update interval: Select to update the time using the NTP server on an hourly, daily, weekly,
or monthly basis.

Configuring Maintenance Settings

Go to Setup System Setup Maintenance.
This chapter describes how to restore the camera to factory default, upgrade firmware version,
etc.
Figure 9-2 Maintenance

78
 Configuring System Settings

Upgrading Firmware
On this page, you can upgrade the firmware of the camera. It takes a few minutes to complete
the process.

• Do not power off the camera during the upgrade.

Note • If an SD card is used in your camera, backup your SD card
contents if necessary before the upgrade.

Follow the steps below to upgrade the firmware:

1. Click CHOOSE FILE and locate the firmware file.
2. Click UPGRADE. The camera starts to upgrade and will reboot automatically when the
upgrade completes.

• If an SD card is used in your camera, it will be formatted

automatically after the upgrade. The formatting may take 5 to
20 minutes.
• After the SD card is formatted, it will be encrypted and its
content cannot be read on other cameras.
Note
• If you want to use the SD card in another camera, format the
SD card in another camera first. For how to format the SD card,
see SD Card Format on page 70.
• A new SD card inserted to camera will also be formatted
automatically after the camera is upgraded.

If the upgrade is successful, the “Reboot system now!! This connection will close” message will
be displayed. After that, re-access the camera. If an SD card is inserted to the camera, wait for
the SD card formatting to complete.

Rebooting the Camera

On this page, you can reboot the camera. It takes about one minute to complete. After it is
completed, the live video page will be displayed in your browser.
If the connection fails after rebooting, manually enter the IP address of the camera in the
address field to resume the connection.

Restoring the Camera

Restore the camera to factory default settings.

79
Honeywell 60 Series IP Camera Software Configuration Guide

Network Setup: Check to retain the Network Type settings (see Configuring Network General
Settings on page 44).
Daylight Saving Time: Check to retain the Daylight Saving Time settings (see Importing
/Exporting Files on page 80).
Focus position: Check to retain the lens focus position using the previously saved position
parameters.
If none of the options is selected, all settings will be restored to factory default. Click
RESTORE and the camera will be rebooted.
After it is completed, the live video page will be displayed in your browser.
If the connection fails after rebooting, manually enter the IP address of the camera in the
address field to resume the connection.

Importing /Exporting Files

Export / Update daylight saving time rules, custom language file, configuration file, and
server status report.
Figure 9-3 Import/Export Files

Export daylight saving time configuration file

Follow the steps below to export daylight saving time configuration file from the camera and
set the start and end time of DST.
1. Click EXPORT under Export daylight saving time configuration file.

80
 Configuring System Settings

2. A file download dialog will be displayed. Click Open to review the XML file or click Save to
store the file for editing.
3. Open the file with Microsoft® Wordpad and locate your time zone; set the start and end
time of DST.
After it is completed, save the file.
In the example below, DST begins each year at 2:00 a.m. on the second Sunday in March and
ends at 2:00 a.m. on the first Sunday in November.

Export CA Certificate
The camera uses HTTPS, a secure communication protocol that verifies the identities of
visited websites and servers and encrypts data exchanged between the client and the server.
When you log in to the camera’s web client for the first time, some browsers may display a
warning that the connection is not private/secure. To access the web client, you must install a
Honeywell-signed security certificate.
1. Click Export to save the root certificate (ca.crt) on your local computer.
2. Go to the directory where you saved the certificate and double-click the certificate. The
Certificate window opens.
3. In the Certificate window, on the General tab, click Install Certificate to open the
Certificate Import Wizard.
4. Click Next to continue.
5. Click Place all certificates in the following store, click Browse, click Trusted Root
Certification Authorities, and then click OK.
6. Click Next, and then click Finish to close the Certificate Import Wizard. A confirmation
dialog box appears with the message “The import was successful.”

81
Honeywell 60 Series IP Camera Software Configuration Guide

7. Click OK, and then click OK to close the Certificate window. And now your browser will not
display a warning that the connection is not private/secure.

Please ensure to install the certificate to ensure a secure

Note communication with the camera and to avoid delays in the web
page navigation.

Export configuration file

Enter a password for exporting the configuration file and then click EXPORT to export all
parameters for the camera and user-defined scripts.

Update daylight saving time rules

Follow the steps below to update daylight saving time rules:
1. Click CHOOSE FILE under Update daylight saving time rules.
2. Select the XML file to update.
3. Click UPLOAD.

Upload configuration file

Follow the steps below to upload a configuration file:
1. Enter the password for uploading the configuration file. The password must be the same
with the password of the configuration file you set for exporting, or the uploading will be
failed. For example, if you set the password A for the configuration file A and you set the
password B for the configuration file B. When you want to upload the configuration file B,
you must use the password B.
2. Click CHOOSE FILE to locate the configuration file and then click UPLOAD to upload the
configuration file.
The model and firmware version of the device should be the same as the configuration file. If
you have set up a fixed IP or other special settings for your device, it is not suggested to
update a configuration file.
If the power is disconnected during firmware upgrade or if there is unknown reason causing
abnormal LED status, and a Restore cannot recover normal working condition, you can
perform the following steps to activate the camera with its backup firmware:
a. Press and hold down the reset button for at least one minute.
b. Power on the camera until the Red LED blinks rapidly.
c. After boot up, the firmware should return to the previous version before the camera
hanged. (The procedure should take 5 to 10 minutes, longer than the normal boot-up
process). When this process is completed, the LED status should return to normal.

Configuring User Accounts Settings

Go to Setup System Setup User Accounts.

82
 Configuring System Settings

This section describes how to create multiple accounts and grant privileges to these
accounts.

Account Management
Figure 9-4 Account Management

The administrator account name is “admin”, which is permanent and cannot be deleted.
The administrator can create up to 20 user accounts.
To create a new user:
1. Select New user from the dropdown list.
2. Enter the new user’s name and password and confirm the password. Some, but not all
special ASCII characters are supported. You can use “!?@#$%=+*-_:,.&^~” in the password
combination.
3. Select the privilege level for the new user account. Click ADD to enable the setting.
The privilege levels are listed below:

Role Privilege
Administrator Full control
Viewer Live, Language

Access rights are sorted by user privilege (Administrator, Operator, and Viewer). Only
administrators can access the Configuration page. Viewers can only access the main page for
live viewing.
To change a user’s access rights or delete user accounts:
1. Select an existing account to modify.
2. Make necessary changes and click UPDATE or DELETE to enable the setting.

Configuring Access List Settings

Go to Setup System Setup Access List.

83
Honeywell 60 Series IP Camera Software Configuration Guide

This section describes how to control access permission by verifying the client PC’s IP
address.
Figure 9-5 Access List

General Settings
Concurrent user number: Simultaneous live viewing for 1~10 clients (including main stream
to third stream). The default value is 10.

Filter
Enable access list filtering: Check this item and click SAVE to enable the access list filtering
function.
Filter type: Select Allow or Deny as the filter type. If you choose Allow Type, only those clients
whose IP addresses are on the Access List below can access the camera, and the others
cannot. On the contrary, if you choose Deny Type, those clients whose IP addresses are on the
Access List below will not be allowed to access the camera, and the others can.
Click ADD and you can add a rule to the following Access List.
Single: This rule allows the user to add an IP address to the Allowed/Denied list.
Network: This rule allows the user to assign a network address and corresponding subnet
mask to the Allow/Deny List. The address and network mask are written in CIDR format.
Range: This rule allows the user to assign a range of IP addresses to the Allow/Deny List.

• The IPv6 access list column will not be displayed unless

you enable IPv6 on the Network page. For more
Note information about IPv6 Settings, see Enable IPv6 on page
45.
• The Range rule only applies to IPv4 addresses.

84
 Configuring System Settings

Administrator IP address
Always allow the IP address to access this device: Check it and add the Administrator’s IP
address in this field to make sure the Administrator can always connect to the device.

85
Honeywell 60 Series IP Camera Software Configuration Guide

10 Viewing System Information

This chapter contains the following sections:
• Log, page 86
• Version, page 87

Log
Go to Setup Information Logs.

System Log
System log displays the system events in a chronological order. The system log is stored in the
camera’s buffer area and will be deleted after the camera is rebooted.
Figure 10-1 System Log

Access Log
Access log displays the access time and IP address of all viewers (including operators and
administrators) in a chronological order. The access log is stored in the camera’s buffer area
and will be will be deleted after the camera is rebooted.

86
 Viewing System Information

Figure 10-2 Access Log

Version
Go to Setup Information Version.
On the Version page, you can view the software version.

87
Honeywell 60 Series IP Camera Software Configuration Guide

11 Troubleshooting
Troubleshooting for Common Issues
Refer to the following guidelines to troubleshoot any performance issues. If you require
additional assistance, contact Honeywell Technical Support (see back cover for contact
information).
Table 11-1 Troubleshooting

Issues Solutions

• Ensure that your browser’s security

settings allow ActiveX controls.
Cannot install/log in to web client. • Ensure that you have a valid network setup
and that you are using the correct login
user name and password.

• Use of a UPS power supply is strongly

Power supply is unstable.
recommended.

Camera webpage has abnormal

• Clear the cache of browser
display.

The audio will not stop automatically

when switching from live page to • Manually turn off the audio on live page
settings page.

88
 Appendix

12 Appendix
List of Symbols
The following is a list of symbols that may appear on the camera:

Symbol Explanation

The WEEE symbol.

This symbol indicates that when the end-user wishes to discard this product, it
must be sent to separate collection facilities for recovery and recycling. By
separating this product from other household-type waste, the volume of waste
sent to incinerators or landfills will be reduced, and thus natural resources will be
conserved.

The UL compliance logo.

This logo indicates that the product has been tested and is listed by UL (formerly
Underwriters Laboratories).

The FCC compliance logo.

This logo indicates that the product conforms to Federal Communications
Commission compliance standards.

The direct current symbol.

This symbol indicates that the power input/output for the product is direct current.

The alternating current symbol.

This symbol indicates that the power input/output for the product is alternating
current.

The RCM compliance logo.

This logo indicates that the product conforms with Australian RCM guidelines.

The CE compliance logo.

This logo indicates that the product conforms to the relevant guidelines/standards
for the European Union harmonization legislation.

The caution symbol.

This symbol indicates important information.

The protective earth (ground) symbol.

This symbol indicates that the marked terminal is intended for connection to the
protective earth/grounding conductor.

89
Honeywell 60 Series IP Camera Software Configuration Guide

Eurasian Conformity (EAC) RoHS

90
 Honeywell Building Technologies – Security Americas (Head Office) Honeywell Building Technologies – Security Россия и СНГ
Honeywell Commercial Security 121059 Moscow, UI, Kiev 7 Russia
715 Peachtree St. NE www.security.honeywell.com/ru
Atlanta, GA 30308  +7 (495) 797-93-71
www.security.honeywell.com/
Honeywell Building Technologies – Security Asia Pacific
 +1 800 323 4576
Building #1, 555 Huanke Road, Zhang Jiang Hi-Tech Park
Honeywell Building Technologies – Security Mexico Pudong New Area, Shanghai, 201203, China
Mexico: Av. Santa Fe 94, Torre A, Piso 1, Col. Zedec, www.asia.security.honeywell.com
CP 0121, CDMX, Mexico.  400 840 2233
Colombia: Edificio Punto 99, Carrera 11a.
98-50, Piso 7, Bogota, Colombia. Honeywell Building Technologies – Security and Fire
clarsupport@honeywell.com (ASEAN)
www.honeywell.com Honeywell International Sdn Bhd
 01.800.083.59.25 Level 25, UOA Corp Tower, Lobby B, Avenue 10, The Vertical,
Bangsar South City, 59200, Kuala Lumpur, Malaysia
Honeywell Colombia SAS Visit Partner Connect: www.partnerconnect.honeywell.com
Carrera 11A # 98-50, Edificio Punto 99, Piso 7 Email: buildings.asean@honeywell.com
Bogotá DC, Colombia Technical support (Small & Medium
Business):
Honeywell Building Technologies – Security Middle East/N. Africa Vietnam: +84 4 4458 3369
Emaar Business Park, Sheikh Zayed Road Thailand: +66 2 0182439
Building No. 2, 2nd floor, 201 Indonesia: +62 21 2188 9000
Post Office Box 232362 Malaysia: +60 3 7624 1530
Dubai, United Arab Emirates Singapore: +65 3158 6830
www.honeywell.com/security/me Philippines: +63 2 231 3380
 +971 44541704 Honeywell Home and Building Technologies (India)
Honeywell Building Technologies – Security Europe/South Africa HBT India Buildings
Aston Fields Road, Whitehouse Industrial Estate Unitech Trade Centre, 5th Floor,
Sector – 43, Block C, Sushant Lok Phase – 1,
Runcorn, WA7 3DL, United Kingdom
Gurgaon – 122002, Haryana, India
www.honeywell.com/security/uk
Visit Partner Connect: www.partnerconnect.honeywell.com
 08448 000 235
Email: HBT-IndiaBuildings@honeywell.com
Honeywell Building Technologies – Security Northern Europe Toll Free No: 1-800-103-0339
 +91 124 4975000
Stationsplein Z-W 961, 1117 CE Schiphol-Oost, The Netherlands
www.security.honeywell.com/nl Honeywell Building Technologies – Security and Fire
 +31 (0) 299 410 200 (Korea)
Honeywell Co., Ltd. (Korea)
Honeywell Building Technologies – Security 5F SangAm IT Tower,
Deutschland 434, Worldcup Buk-ro, Mapo-gu,
Johannes-Mauthe-Straße 14 72458 Albstadt, Germany Seoul 03922, Korea
www.security.honeywell.de Visit: http://www.honeywell.com
 +49 (0) 7431 801-0 Email: info.security@honeywell.com
Customer support: HSG-CS-KR@honeywell.com; +82 1522-8779
Honeywell Building Technologies – Security France
 +82-2-799-6114
Immeuble Lavoisier
Parc de Haute Technologie 3-7 rue Georges Besse Honeywell Building Technologies – Security & Fire (Pacific)
92160 Antony, France Honeywell Ltd
www.security.honeywell.com/fr 9 Columbia Way
 +33 (0) 1 40 96 20 50 BAULKHAM HILLS NSW 2153
Visit: www.honeywellsecurity.com.au
Honeywell Building Technologies – Security Italia SpA Email: hsf.comms.pacific@Honeywell.com
Via Achille Grandi 22, 20097 San Donato Milanese (MI), Technical support:
ITALY Australia: 1300 220 345
www.security.honeywell.com/it New Zealand: +64 9 623 5050

Honeywell Building Technologies – Security España

Josefa Valcárcel, 24
28027 - Madrid
España
www.honeywell.com
 +34 902 667 800

www.honeywell.com/security
+1 800 323 4576 (North America only)
https://www.honeywellsystems.com/ss/techsupp/index.html
Document 800-26140 Rev A – 03/2020
© 2020 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from
Honeywell. The information in this publication is believed to be accurate in all respects. However, Honeywell cannot assume responsibility for any
consequences resulting from the use thereof. The information contained herein is subject to change without notice. Revisions or new editions to
this publication may be issued to incorporate such changes. For patent information, see www.honeywell.com/patents.