SINEAX DME 401 with RS 485 Interface

Programmable Multi-Transducer

without analog outputs, transfer of data via a MODBUS®-

interface

Application
SINEAX DME 401 (Fig. 1) is a programmable transducer with a
RS 485 bus interface (MODBUS®). It supervises several variables
of an electrical power system simultaneously.

The RS 485 interface enables the user to determine the number

of variables to be supervised (up to the maximum available). The
levels of all internal counters that have been configured (max. 4) can
also viewed. Provision is made for programming the SINEAX DME
401 via the bus. A standard EIA 485 interface can be used.

The transducers are also equipped with an RS 232 serial interface Fig. 1. SINEAX DME 401 in housing T24,
to which a PC with the corresponding software can be connected clipped onto a top-hat rail.
for programming or accessing and executing useful ancillary
functions. This interface is needed for bus operation to configure
the device address, the Baud rate and possibly increasing the
Measured variables Output Types
telegram waiting time (if the master is too slow) defined in the
MODBUS® protocol. Without analog outputs,
with bus interface DME 401
The usual methods of connection, the types of measured variables, RS 485 (MODBUS)
their ratings and the type of internal energy/metering are the main Current, voltage (rms), 4 analog outputs and
parameters that can be programmed. active/reactive/apparent power bus interface RS 485
DME 440
cosϕ, sinϕ, power factor (MODBUS) see data sheet
The ancillary functions include a power system check and a facility DME 440-1 Le
for printing nameplate. RMS value of the current with
wire setting range (bimetal 2 analog outputs and
The transducer fulfils all the essential requirements and regulati- measuring function) 4 digital outputs DME 424
ons concerning electromagnetic compatibility (EMC) and safety or
Slave pointer function for the
(IEC 1010 resp. EN 61 010). It was developed and is manufac- 4 analog outputs and
measurement of the RMS
tured and tested in strict accordance with the quality assurance 2 digital outputs
value IB DME 442
standard ISO 9001. see data sheet
Frequency DME 424/442-1 Le
Average value of the currents Data bus LON
with sign of the active power see data sheet DME 400
(power system only) DME 400-1 Le
PROFIBUS DP
see data sheet DME 406
DME 406-1 Le
Features / Benefits
● For all heavy-current power system variables
● Simultaneous measurement of several variables of a heavy-current
● Input voltage up to 693 V (phase-to-phase)
power system / Full supervision of an asymmetrically loaded four-
wire power system. rated current 1 to 6 A, rated voltage 57 to 400 V ● Transfer of data via a MODBUS® interface
(phase-to-neutral) or 100 to 693 V (phase-to-phase) ● High accuracy: 0.2% (under reference conditions)

Camille Bauer Data sheet DME 401-1 Le – 02.14 1

SINEAX DME 401 with RS 485 Interface
Programmable Multi-Transducer
● 4 integrated energy meters, storage every each 203 s, storage for Symbols Meaning
20 years
I Input current
● Windows software with password protection for programming, data
I1 AC current L1
analysis, power system status simulation, acquisition of meter data
and making settings I2 AC current L2
● DC-, AC-power pack with wide power supply tolerance / Universal I3 AC current L3

● Provision for either snapping the transducer onto top-hat rails or Ir Rated value of the input current
securing it with screws to a wall or panel IM Average value of the currents (I1 + I2 + I3) / 3
IMS Average value of the currents and sign of the
1 2
active power (P)
I1

I2 IB RMS value of the current with wire setting range

3 4 5 (bimetal measuring function)
I3
A/D μP IBT Response time for IB
L1
6 BS Slave pointer function for the measurement of the
L2 RMS value IB
RS-
8 485
L3 7 BST Response time for BS
N
UH
9 RS-232 ϕ Phase-shift between current and voltage
F Frequency of the input variable
1 = Input transformer 6 = Electrical insulation
2 = Multiplexer 7 = Programming interface RS-232 Fn Rated frequency
3 = Latching stage 8 = Bus RS 485 (MODBUS)
4 = A/D converter 9 = Power supply P Active power of the system P = P1 + P2 + P3
5 = Microprocessor
P1 Active power phase 1 (phase-to-neutral L1 – N)
Fig. 2. Block diagram.
P2 Active power phase 2 (phase-to-neutral L2 – N)
P3 Active power phase 3 (phase-to-neutral L3 – N)

Q Reactive power of the system Q = Q1 + Q2 + Q3

Q1 Reactive power phase 1 (phase-to-neutral L1 – N)
Symbols Q2 Reactive power phase 2 (phase-to-neutral L2 – N)
Symbols Meaning Q3 Reactive power phase 3 (phase-to-neutral L3 – N)
X Measured variable
S Apparent power of the system
X0 Lower limit of the measured variable
S = √ I12 + I22 + I32 · √ U12 + U22 + U32
X1 Break point of the measured variable
S1 Apparent power phase 1 (phase-to-neutral L1 – N)
X2 Upper limit of the measured variable
S2 Apparent power phase 2 (phase-to-neutral L2 – N)
U Input voltage S3 Apparent power phase 3 (phase-to-neutral L3 – N)
Ur Rated value of the input voltage Sr Rated value of the apparent power of the system
U 12 Phase-to-phase voltage
L1 and L2 PF Active power factor cosϕ = P/S
U 23 Phase-to-phase voltage PF1 Active power factor phase 1 P1/S1
L2 and L3
PF2 Active power factor phase 2 P2/S2
U 31 Phase-to-phase voltage
L3 and L1 PF3 Active power factor phase 3 P3/S3
U1N Phase-to-neutral voltage L1 – N
QF Reactive power factor sin ϕ = Q/S
U2N Phase-to-neutral voltage L2 – N
QF1 Reactive power factor phase 1 Q1/S1
U3N Phase-to-neutral voltage L3 – N
QF2 Reactive power factor phase 2 Q2/S2
UM Average value of the voltages
(U1N + U2N + U3N) / 3 QF3 Reactive power factor phase 3 Q3/S3

2 Data sheet DME 401-1 Le – 02.14 Camille Bauer

 SINEAX DME 401 with RS 485 Interface
Programmable Multi-Transducer

Symbols Meaning Technical data

LF Power factor of the system Inputs
LF = sgnQ · (1 – ⏐PF⏐)
Input variables: see Table 2 and 3
LF1 Power factor phase 1
sgnQ1 · (1 – ⏐PF1⏐) Measuring ranges: see Table 2 and 3
Waveform: Sinusoidal
LF2 Power factor phase 2
sgnQ2 · (1 – ⏐PF2⏐) Nominal frequency: 50, 60 or 16 2/3 Hz
LF3 Power factor phase 3 Consumption [VA]: Voltage circuit: U2 / 400 kΩ
sgnQ3 · (1 – ⏐PF3⏐) Condition:
external power supply
H Power supply Current circuit: ≤ I2 · 0.01 Ω
Hn Rated value of the power supply
Continuous thermal ratings of inputs

CT c.t. ratio Current circuit 10 A 400 V single-phase AC system

VT v.t. ratio 693 V three-phase system
Voltage circuit 480 V single-phase AC system
831 V three-phase system

Short-time thermal rating of inputs

Applicable standards and regulations Input variable Number of Duration Interval
IEC 688 or inputs of between two
EN 60 688 Electrical measuring transducers for con- overload overloads
verting AC electrical variables into analog Current circuit 400 V single-phase AC system
and digital signals
693 V three-phase system
IEC 1010 or
EN 61 010 Safety regulations for electrical measuring, 100 A 5 3s 5 min.
control and laboratory equipment 250 A 1 1s 1 hour
IEC 529 or Voltage circuit 1 A, 2 A, 5 A
EN 60529 Protection types by case (code IP) Single-phase
IEC 255-4 Part E5 High-frequency disturbance test (static AC system
relays only) 600 V
Hintern: 1.5 Ur 10 10 s 10 s
IEC 1000-4-2, 3, 4, 6 Electromagnetic compatibility for in-
dustrialprocess measurement and control Three-phase
equipment system
1040 V
EN 55 011 Electromagnetic compatibility of data
Hintern: 1.5 Ur 10 10 s 10 s
processing and telecommunication
equipment
MODBUS® (bus interface RS-485)
Limits and measuring principles for radio
interference and information equipment Terminals: Screw terminals, terminals
23, 24 and 25
IEC 68-2-1, 2, 3, 6, 27
or EN 60 068-2-1, Connecting cable: Screened twisted pair
2, 3, 6, 27 Ambient tests Max. distance: Approx. 1200 m (approx. 4000 ft.)
-1 Cold, -2 Dry heat, -3 Damp heat,
Baudrate: 1200 … 9600 Bd (programmable)
-6 Vibration, -27 Shock
Number of bus
DIN 40 110 AC quantities
stations: 32 (including master)
DIN 43 807 Terminal markings
IEC 1036 Alternating current static watt-hour meters
for active energy (classes 1 and 2)
DIN 43 864 Current interface for the transmission
+ – GND
of impulses between impulse encoder
counter and tarif meter 23 24 25 26

UL 94 Tests for flammability of plastic materials

for parts in devices and appliances MODBUS® is a registered trademark of the Schneider Automation Inc.

Camille Bauer Data sheet DME 401-1 Le – 02.14 3

SINEAX DME 401 with RS 485 Interface
Programmable Multi-Transducer
Reference conditions Programming connector on transducer
Ambient temperature: 15 … 30 °C Interface: RS 232 C
Pre-conditioning: 30 min. acc. to EN 60 688
DSUB socket: 9-pin
Input variable: Rated useful range
Power supply: H = Hn ± 1% 9
5
GND
Active/reactive factor: cosϕ = 1 resp. sinϕ = 1 CTS DTR The interface is electrically insulated
RTS TXD
Frequency: 50 … 60 Hz, 16 2/3 Hz RXD from all other circuits.
DSR
6 1
Waveform: Sinusoïdal, form factor 1.1107
Miscellaneous: EN 60 688

System response Installation data

Accuracy class: 0.2 resp. 0.4 at applications with Housing: Housing T24
phase-shift See section “Dimensioned dra-
wings”
Duration of the
measurement cycle: Approx. 0.5 to 1.2 s at 50 Hz, Housing material: Lexan 940 (polycarbonate),
depending on measured variable flammability class V-0 acc. to UL
and programming 94, self-extinguishing, non-dripping,
free of halogen
Response time: 1 … 2 times the measurement
cycle Mounting: For snapping onto top-hat rail
(35 × 15 mm or 35 × 7.5 mm) acc.
Influencing quantities and permissible variations to EN 50 022
Acc. to EN 60 688 or
directly onto a wall or panel using
Safety the pull-out screw hole brackets
Protection class: II (protection isolated,
EN 61 010-1) Orientation: Any
Enclosure protection: IP 40, housing Weight: Approx. 0.7 kg
IP 20, terminals
Installation category: III Terminals
Insulation test Type: Screw terminals with wire guards
(versus earth): Input voltage: AC 400 V
Input current: AC 400 V Max. wire gauge: ≤ 4.0 mm2 single wire or
2 × 2.5 mm2 fine wire
RS 485: DC 40 V
Power supply: AC 400 V
DC 230 V Ambient tests
Surge test: 5 kV; 1.2/50 μs; 0.5 Ws EN 60 068-2-6: Vibration
Test voltage: 50 Hz, 1 min. acc. to EN 61 010-1 Acceleration: ±2g
5550 V, inputs versus all other circuits
Frequency range: 10 … 150 … 10 Hz, rate of frequency
as well as outer surface
sweep:
3250 V, input circuits versus each 1 octave/minute
other
Number of cycles: 10, in each of the three axes
3700 V, power supply versus RS 485
and SCI as well as outer surface EN 60 068-2-27: Shock
490 V, RS 485 versus SCI as well as Acceleration: 3 × 50 g
outer surface 3 shocks each in 6 directions
Power supply EN 60 068-2-1/-2/-3: Cold, dry heat, damp heat
DC-, AC-power pack (DC and 50 … 60 Hz)
Table 1: Rated voltages and tolerances Ambient conditions

Rated voltage UN Tolerance Variations dues to ambient

temperature: ± 0.2% / 10 K
24 … 60 V DC, AC DC – 15 … + 33%
AC ± 10% Nominal range of use for
85 … 230 V DC, AC
temperature: 0…15…30…45 °C
Consumption: ≤ 9 W resp. ≤ 10 VA (usage group II)

4 Data sheet DME 401-1 Le – 02.14 Camille Bauer

 SINEAX DME 401 with RS 485 Interface
Programmable Multi-Transducer

Operating temperature: – 10 to + 55 °C Altitude: 2000 m max.

Storage temperature: – 40 to + 85 °C Indoor use statement!
Annual mean
relative humidity: ≤ 75%

Table 2: Ordering information

DESCRIPTION MARKING
1. Mechanical design
Housing T24 for rail and wall mounting 401 - 1
2. Rated input frequency
50 Hz (60 Hz possible without additional error; 16 2/3 Hz, additional error 1.25) 1
60 Hz (50 Hz possible without additional error; 16 2/3 Hz, additional error 1.25) 2
16 2/3 Hz (not re-programming by user, 50/60 Hz possible, but with additional error 1.25) 3
3. Power supply
Nominal range 24 … 60 V DC, AC 7
Nominal range 85 … 230 V DC, AC 8
4. Power supply connection
External (standard) 1
Internal from measuring input 2
Not available for rated frequency 16 2/3 Hz and applications A15 / A16 / A24 (see Table 3)
Caution: The power supply voltage must agree with the input voltage (Table 3)!
5. Test certificate
None supplied 0
With test certificate in German D
With test certificate in English E
6. Configuration
Basic configuration, programmed (not available if the power supply is taken from the measuring input) 0
Programmed acc. to specification 9
All the programming data must be entered on Form W 2408e (see appendix) and the form must be
included with the order!

Table 3: Programmierung
APPLICATION
DESCRIPTION
A11… A16 A34 A24/A44
1. Application (system)
Single-phase AC A11 ––– –––
3-wire, 3-phase symmetric load, phase-shift U: L1-L2, I: L1* A12 ––– –––
3-wire, 3-phase symmetric load A13 ––– –––
4-wire, 3-phase symmetric load A14 ––– –––
3-wire, 3-phase symmetric load, phase-shift U: L3-L1, I: L1* A15 ––– –––
3-wire, 3-phase symmetric load, phase-shift U: L2-L3, I: L1* A16 ––– –––
3-wire, 3-phase asymmetric load ––– A34 –––
4-wire, 3-phase asymmetric load ––– ––– A44
4-wire, 3-phase asymmetric load, open-Y ––– ––– A24

Camille Bauer Data sheet DME 401-1 Le – 02.14 5

SINEAX DME 401 with RS 485 Interface
Programmable Multi-Transducer

APPLICATION
DESCRIPTION
A11… A16 A34 A24/A44
2. Rated input voltage
Rated value Ur = 57.7 V U01 ––– –––
Rated value Ur = 63.5 V U02 ––– –––
Rated value Ur = 100 V U03 ––– –––
Rated value Ur = 110 V U04 ––– –––
Rated value Ur = 120 V U05 ––– –––
Rated value Ur = 230 V U06 ––– –––
Rated value Ur (Ur [V] 57 to 400) [V] U91 ––– –––
Rated value Ur = 100 V U21 U21 U21
Rated value Ur = 110 V U22 U22 U22
Rated value Ur = 115 V U23 U23 U23
Rated value Ur = 120 V U24 U24 U24
Rated value Ur = 400 V U25 U25 U25
Rated value Ur = 500 V U26 U26 U26
Rated value Ur (Ur [V] > 100 to 693) [V] U93 U93 U93
Lines U01 to U06: Only for single phase AC current or 4-wire, 3-phase symmetric load
3. Rated input current
Rated value Ir = 1 A V1 V1 V1
Rated value Ir = 2 A V2 V2 V2
Rated value Ir = 5 A V3 V3 V3
Rated value Ir (Ir [A] > 1 to 6) [A] V9 V9 V9
4. Primary rating (voltage and current transformer)
Without specification of primary rating W0 W0 W0
CT = ________ A VT = ________kV
Specify transformer ratio primary, e.g. 33 kV/1000 A
W9 W9 W9
The secondary ratings must correspond to the rated input voltage and current speci-
fied for feature 2, respectively 3.
5. Energy meter 1
Not used EA00 EA00 EA00
I System [Ah] EA50 ––– –––
I1 L1 [Ah] ––– EA51 EA51
I2 L2 [Ah] ––– EA52 EA52
I3 L3 [Ah] ––– EA53 EA53
S System [VAh] EA54 EA54 EA54
S1 L1 [VAh] ––– ––– EA55
S2 L2 [VAh] ––– ––– EA56
S3 L3 [VAh] ––– ––– EA57
P System (incoming) [Wh] EA58 EA58 EA58
P1 L1 (incoming) [Wh] ––– ––– EA59
P2 L2 (incoming) [Wh] ––– ––– EA61
P3 L3 (incoming) [Wh] ––– ––– EA61
Q System (inductive) [Varh] EA62 EA62 EA62
Q1 L1 (inductive) [Varh] ––– ––– EA63
Q2 L2 (inductive) [Varh] ––– ––– EA64

6 Data sheet DME 401-1 Le – 02.14 Camille Bauer

 SINEAX DME 401 with RS 485 Interface
Programmable Multi-Transducer

APPLICATION
DESCRIPTION
A11… A16 A34 A24/A44
Q3 L3 (inductive) [Varh] ––– ––– EA65
P System (outgoing) [Wh] EA66 EA66 EA66
P1 L1 (outgoing) [Wh] ––– ––– EA67
P2 L2 (outgoing) [Wh] ––– ––– EA68
P3 L3 (outgoing) [Wh] ––– ––– EA69
Q System (capacitive) [Varh] EA70 EA70 EA70
Q1 L1 (capacitive) [Varh] ––– ––– EA71
Q2 L2 (capacitive) [Varh] ––– ––– EA72
Q3 L3 (capacitive) [Varh] ––– ––– EA73
6. Energy meter 2
Same as energy meter 1, but markings start with a capital F FA .. FA .. FA ..
7. Energy meter 3
Same as energy meter 1, but markings start with a capital G GA .. GA .. GA ..
8. Energy meter 4
Same as energy meter 1, but markings start with a capital H HA .. HA .. HA ..

* Basic accuracy 0.4 c

Standard accessories
1 Operating Instructions for SINEAX DME 401 in three languages: German, French, English
1 blank type label, for recording programmed settings
1 interface definition DME 401: German, French or English

Camille Bauer Data sheet DME 401-1 Le – 02.14 7

SINEAX DME 401 with RS 485 Interface
Programmable Multi-Transducer

Electrical connections

Function Connect. RS 485

Measuring input AC current IL1 1/3 Tx/Rx
IL2 4/6 + – GND
IL3 7/9
AC voltage UL1 2
UL2 5 Front
UL3 8 15 16 17 18 19 20 21 22 23 24 25 26
N 11
RS 485 Tx + / Rx + 23
(MODBUS) Tx – / Rx – 24
GND 25 RS 232
Power supply AC ~ 13
~ 14
DC + 13
– 14

If power supply is taken from the measured voltage 1 2 3 4 5 6 7 8 9 11 13 14

internal connections are as follows:
Application (system) Internal connection
Terminal / System
Single-phase AC current 2 / 11 (L1 – N) IL1 IL1 IL2 IL2 IL3 IL3
4-wire 3-phase 2 / 11 (L1 – N) UL1 UL2 UL3 N
symmetric load
All other (apart from 2/5 (L1 – L2) Measuring input
A15 / A16 / A24)

Measuring inputs
System /
application Terminals

2 11 1 3 2 11 1 3 2 11 1 3

Single-phase
u v
AC system
k l k l
U V
L1 L1 L1
K L K L
N N N

8 Data sheet DME 401-1 Le – 02.14 Camille Bauer

 SINEAX DME 401 with RS 485 Interface
Programmable Multi-Transducer

Measuring inputs
System /
application Terminals

2 5 8 1 3 2 5 8 1 3 2 5 8 1 3

u v u v

k l k l
U V U V
L1 L1 L1
K L K L
3-wire L2 L2 L2
3-phase L3 L3 L3
symmetric
load
Connect the voltage according to the following table for current measurement in L2 or L3:
I: L1

Current transf. Terminals 2 5 8

L2 1 3 L2 L3 L1
L3 1 3 L3 L1 L2

2 5 1 3 2 5 1 3 2 5 1 3

u v

k l k l
U V
3-wire
L1 L1 L1
3-phase K L K L
L2 L2 L2
symmetric
load L3 L3 L3
Phase shift
U: L1 – L2 Connect the voltage according to the following table for current measurement in L2 or L3:
I: L1
Current transf. Terminals 2 5
L2 1 3 L2 L3
L3 1 3 L3 L1

8 2 1 3 8 2 1 3 8 2 1 3

u v
3-wire k l k l

3-phase U V
L1 L1 L1
symmetric K L K L
load L2 L2 L2
Phase shift L3 L3 L3
U: L3 – L1
I: L1
Connect the voltage according to the following table for current measurement in L2 or L3:

Current transf. Terminals 8 2

L2 1 3 L1 L2
L3 1 3 L2 L3

Camille Bauer Data sheet DME 401-1 Le – 02.14 9

SINEAX DME 401 with RS 485 Interface
Programmable Multi-Transducer

Measuring inputs
System /
application Terminals

5 8 1 3 5 8 1 3 5 8 1 3

3-wire u v

3-phase k l k l
U V
symmetric L1 L1 L1
load K L K L
L2 L2 L2
Phase-shift
U: L2 – L3 L3 L3 L3
I: L1
Connect the voltage according to the following table for current measurement in L2 or L3:

Current transf. Terminals 5 8

L2 1 3 L3 L1
L3 1 3 L1 L2

2 11 1 3 2 11 1 3 2 11 1 3

u v

k l k l
U V
4-wire L1 L1 L1
3-phase K L K L
L2 L2 L2
symmetric
load L3 L3 L3
I: L1 N N N

Connect the voltage according to the following table for current measurement in L2 or L3:

Current transf. Terminals 2 11

L2 1 3 L2 N
L3 1 3 L3 N

2 5 8 1 3 7 9 2 5 8 1 3 7 9 2 5 8 1 3 7 9

u v u v

k l k l
U V U V
L1 L1 L1
K L k l K L k l
L2 L2 L2
3-wire L3 L3 L3
K L K L
3-phase
asymmetric 2 5 8 1 3 7 9
load u u u

x x x

X X X
k l
U U U
L1
K L k l
L2
L3
K L

10 Data sheet DME 401-1 Le – 02.14 Camille Bauer

 SINEAX DME 401 with RS 485 Interface
Programmable Multi-Transducer

Measuring inputs
System /
application Terminals

2 5 8 11 1 3 4 6 7 9 2 5 8 11 1 3 4 6 7 9

k l
k l
L1 L1
K L k l
L2 L2
K L
L3 L3
K L
4-wire N N
3-phase
asymmetric 2 5 8 11 1 3 4 6 7 9
u u u
load
x x x

X X X
k l
U U U k l
L1
K L k l
L2
K L
L3 3 single-pole insulated voltage transformers
K L
N in high-voltage system

1 2 3 4 5 6 7 8 9 11
2 8 11 1 3 4 6 7 9
u u

x x
4-wire k k k
X X l l l
3-phase k l
k l UU
asymmetric L1 L1
load, K L k l K L L
L2 L2
Open Y K L K L
connection L3 L3
K L K L
N N

2 single-pole insulated voltage transformers

Low-voltage system in high-voltage system

Connecting devices to the bus

The RS 485 interface of the DME 401 is galvanically isolated from
all other circuits. For an optimal data transmission the devices are
Relationship between PF, QF and LF connected via a 3-wire cable, consisting of a twisted pair cable
(for data lines) and a shield. There is no termination required. A
Output shield both prevents the coupling of external noise to the bus and
ind. cap. ind. cap. limits emissions from the bus. The shield must be connected to
solid ground.
QF You can connect up to 32 members to the bus (including master).
PF
Basically devices of different manufacturers can be connected to
the bus, if they use the standard MODBUS® protocol. Devices
without galvanically isolated bus interface are not allowed to be
connected to the shield.
–180 –90 0 90 180 ϕ
The optimal topology for the bus is the daisy chain connection
LF
from node 1 to node 2 to node n. The bus must form a single
continuous path, and the nodes in the middle of the bus must
have short stubs. Longer stubs would have a negative impact on
signal quality (reflection at the end). A star or even ring topology
outgoing incoming outgoing is not allowed.
There is no bus termination required due to low data rate. If you
Fig. 3. Active power PF ––––, reactive power QF ------, got problems when using long cables you can terminate the
power factor LF – - – - –. bus at both ends with the characteristic impedance of the cable

Camille Bauer Data sheet DME 401-1 Le – 02.14 11

SINEAX DME 401 with RS 485 Interface
Programmable Multi-Transducer

(normally about 120 Ω). Interface converts RS232⇔RS485 or Table 4: Accessories and spare parts
RS485 interface cards often have a built-in termination network
which can be connected to the bus. The second impedance Description Order No.
then can be connected directly between the bus terminals of the Programming cable 980 179
device far most.
Configuration software DME 4 146 557
Fig. 4 shows the connection of transducers DME 401 to the for SINEAX/EURAX DME 424, 440, 442,
MODBUS. The RS 485 interface can be realized by means of SINEAX DME 400, 401 and 406
PC built-in interface cards or interface converters. Both is shown
Windows 3.1x, 95, 98, NT and 2000
using i.e. the interfaces 13601 and 86201 of W & T (Wiesemann
on CD in German, English, French, Italian
& Theis GmbH). They are configured for a 2-wire application with
and dutch
automatic control of data direction. These interfaces provide a
galvanic isolation and a built-in termination network. (Download free of charge under
+5V www.camillebauer.com)
Master
In addition, the CD contains all configuration
programmes presently available for Camille Bauer
GND 25 products.
Slave 1 Tx-/Rx- 24
Tx+/Rx+ 23 Operating Instructions DME 401-1 B d-f-e, 146 804
Built-in RS485 interface card
Signal GND
5 SINEAX DME 440 in three languages: German, English and French
1
Data Out A
6
Data Out B
2
Data In A
7
Data In B
3 GND 2d
Handshake Out A Slave 2
8
Handshake Out B Tx-/Rx- 6z
4
Handshake In A
9 Tx+/Rx+ 6d
Handshake In B

PC with interface 13601 of W & T EURAX DME 440

With converter RS232/RS485
5 5
GND GND Signal GND
3 1
TxD Din Data Out A
2 6
RxD Dout Data Out B
2
Data In A
7
Data in B GND 25
4 3 Slave n
DTR Handshake Out A
6 8 Tx-/Rx- 24
DSR Handshake Out B
7 4
RTS Handshake In A Tx+/Rx+ 23
8 9
CTS Handshake In B

PC Interface 86201 of W & T SINEAX DME 401

Fig. 4

Important:
– Each device connected to the bus must have a unique
address
– All devices must be adjusted to the same baudrate.
Description Order No.
Dimensioned drawings SINEAX A 200 154 063
15 16 17 18 19 20 21 22 23 24 25 26 Interconnecting cable 154 071
sub D 9 pol.
mal/male 1.8 m
157
150

1 2 3 4 5 6 7 8 9 11 13 14

87.5 124

Fig. 5. SINEAX DME 401 in housing T24 clipped onto a top-hat rail
(35 × 15 mm or 35×7.5 mm, acc. to EN 50 022).
19 6.5
Ø 4.5

15 16 17 18 19 20 21 22 23 24 25 26
Rely on us.

Camille Bauer Ltd

150

181
165

Aargauerstrasse 7
CH-5610 Wohlen / Switzerland
1 2 3 4 5 6 7 8 9 11 13 14 Phone: +41 56 618 21 11
12 Fax: +41 56 618 21 21
87.5 123.4

Fig. 6. SINEAX DME 401 in housing T24 screw hole mounting brackets info@camillebauer.com
pulled out. www.camillebauer.com

Subject to change without notice • Edition 02.14 • Data sheet DME 401-1 Le
Appendix: PROGRAMMING FOR
SINEAX TYPE DME 401

without analog outputs, with RS 485 Interface (MODBUS®)

(see Data Sheet DME 401-1 Le, Table 3: “Programming”)

Customer / Agent: Date:

Order No. / Item: Delivery date:

No of instruments:

Type of instruments (marking):

Codes for features 1 to 8:

Features 1 to 8 concern data for configuring the software.

1. Application

A System

2. Rated input voltage, rated value

U Ur = V

3. Rated input current, rated value

V Ir = A

4. Primary rating
VT = kV CT = A
Specify transformer ratio primary, e.g. 33 kV, 1000 A
W
The secondary ratings must correspond to the rated input voltage and
current specified for feature 2, respectively 3.

E A 5. Energy meter 1

F A 6. Energy meter 2

G A 7. Energy meter 3

H A 8. Energy meter 4

W 2408 e