CETUS x12 Patient Monitor
Features
• 12.1” color TFT LCD screen
• 8 waveform display, up to 12-lead ECG analysis
• Useful calculation
(Hemodynamic, Drug Dose, Oxygenation, Ventilation)
• Pacemaker detection
• ST & arrhythmia analysis
• OxyCRGs screen
• Wired/Wireless CMS, support HL7 protocol to HIS
• SpO2 pulse-tone modulation (Pitch Tone)
• MEWS (Modified Early Warning Score)
• Graphical & tabular trend review (120 hours)
• Rechargeable Lithium-Ion Battery (2600 mAh)
12.1”color TFT LCD screen, wide and flat screen design,ecnomic and reliable
Configuration: ECG+SpO2+NIBP+2TEMP+PR+RESP, Li-ion battery
Optional: Touch-Screen, 12-lead ECG, Masimo SpO2, 2/4/6 IBP, C.O., EtCO2, Multi-Gas, BIS, NMT,
VGA, Thermal Recorder, Wired/Wireless CMS
Technical Specifications
Display RESP
12.1” TFT (touch screen optional) Measurement method: Thoracic electrical
Resolution: 800 x 600 bioimpedance
Number of traces: 8 waveforms Rate: 0 – 150 bpm
Measuring lead: Lead I, II
ECG Wave gain: ×0.25, ×0.5, ×1, ×2
Lead type: 3-lead, 5-lead, 12-lead Respiratory impedance range: 0.5-5Ω
ECG waveform: 2 channels, 7 channels, Baseline impedance: 500-4000Ω
12 channels Gain: 10 grades
Display sensitivity: 2.5 mm/mV (×0.25), Scan speed: 6.25 mm/s, 12.5 mm/s, 25 mm/s
5 mm/mV (×0.5), 10 mm/mV (×1.0),
20 mm/mV (×2.0) Pulse Rate
Wave sweep speed: 6.25 mm/s, 12.5 mm/s, Range: 30~254 bpm
25 mm/s, 50 mm/s Resolution: 1bpm
Bandwidth Accuracy: ±2bpm (non-motion)
Diagnostic mode: 0.05 Hz~100 Hz ±5bpm (motion)
Monitor mode: 0.5 Hz~40 Hz Refreshing rate: 1s
Surgery mode: 1Hz~20Hz
Strong filter mode: 5 Hz~20 Hz TEMP
CMRR >100 dB Accuracy: ±0.1 °C or ±0.2 °C °F (without probe)
Notch: 50/60 Hz notch filter can be set to Measurement range: 5~50 °C (41~122 °F)
on or off Channel: Two channels
Differential input impedance >5MΩ Resolution: 0.1 °C
Electrode polarization voltage range: ±400 mV Parameters: T1,T2 and TD
Baseline recovery time <3s after defibrillation
(in monitor and surgery mode)
Calibration signal: 1mV (peak - peak),
accuracy ±3%
7-lead ECG
www.axcentmedical.com
CETUS x12 Patient Monitor
Technical Specifications
NIBP SpO2
Measurement method: Automatic oscillome- Measurement range: 0-100%
tric method Resolution: 1%
Operating mode: Manual, automatic, Accuracy: ±2% (70-100%, Adult/Pediatric);
continuous ±3% (70-100%, Neonate);
Measurement unit: mmHg/kPa selectable 0-69%, unspecified
Typical measurement time: 20~40 s Refreshing Rate: 1s
Measurement type: Systolic, Diastolic, Mean
Measurement range (mmHg) Masimo SET® SpO2 (Optional)
Range of Systolic pressure: Adult 40-270 Measurement range: 0-100%
Pediatric 40-200 Resolution: 1%
Neonatal 40-135 Accuracy: ±2% (70-100%, Adult/Pediatric,
Range of Diastolic pressure: Adult 10-210 non-motion, low prefusion);
Pediatric 10-150 ±3% (70-100%, Neonate,
Neonatal 10-95 non-motion);
Range of Mean pressure: Adult 20-230 ±3% (70-100%, motion);
Pediatric 20-165 0-69%, unspecified
Neonatal 20-105 Refreshing Rate: 1s
Measurement accuracy
Recorder (Optional)
Maximum average error: ±5 mmHg
Built-in, Thermal dot array
Maximum standard deviation: 8 mmHg
Horizontal resolution: 16 dots/mm (25 mm/s
Resolution: 1 mmHg
paper speed)
Interval: 1, 3, 4, 5, 10, 15, 30, 60, 90, 120, 180,
Vertical resolution: 8 dots/mm
240, 480 minutes
Paper speed: 25 mm/s, 50 mm/s
Overpressure protection: Software and
Number of waveform channels: 3
hardware, double safety protection
Cuff pressure range: 0-280 mmHg
Operation Environment
Power: AC 100-250V, 50/60Hz
Temperature: 5-40 °C
Humidity: <80%
Patient Range: Adult, Pediatric, Neonate
Battery backup: Standard 2-3 hrs (2.600 mAh),
optional 3-5 hrs (4.800 mAh)
