NOTES:

THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL, OR IN PART, SHALL BE OBTAINED FROM THIS DRAWING WITHOUT THE WRITTEN CONSENT OF SAUDI ARAMCO.
1. LENGTHS OF JACK SCREWS BETWEEN
BRACKETS ARE FOR JOINTS WITH SPECTACLE
PLATES OR BLINDS, OTHER LENGTHS ARE
A
FOR ORIFICE FLANGES.

L= INDICATED LENGTH
C

JACK SCREW CONTINUOUSLY

THREADED IN ACCORDANCE WITH
ANSI B1.1, UNC SERIES CLASS
2A FIT.

DRILL AND TAP TWO HOLES TO SUIT MAY BE FABRICATED BY WELDING

JACK SCREWS IN ONE FLANGE OF JOINT. C SECTION A-A NUT TO STUD BOLT.
IF ONE FLANGE OF JOINT IS AN EQUIPMENT HEAD MAY BE EITHER SQUARE
FLANGE OR VALVE FLANGE, BOTH TAPPED
OR HEXAGONAL.

JACK SCREW SIZE FOR VARIOUS FLANGE RATINGS ( SEE NOTE-1 )

CLASS 150 CLASS 300 CLASS 600 CLASS 600 CLASS 900 CLASS 1500
R.F. R.F. R.F. R.J. R.J. R.J.
DIA. LENGTH DIA. LENGTH DIA. LENGTH DIA. LENGTH DIA. LENGTH DIA. LENGTH
REVISION NOTE - 1 :
mm. in. mm. in. mm. in. mm. in. mm. in. mm. in. mm. in. mm. in. mm. in. mm. in. mm. in. mm. in.
CONSOLIDATED SHEET NOS. 1 & 2 INTO SHEET NO. 1
16 ⅝ 75 ( 75 ) 3 ( 3 ) 16 ⅝ 75 ( 75 ) 3 ( 3 ) 16 ⅝ 75 ( 75 ) 3 ( 3 ) 16 ⅝ 100 ( 115 ) 4 ( 4½) 16 ⅝ 100 ( 140 ) 4 ( 5½) 16 ⅝ 100 ( 140 ) 4 ( 5½)
COMPLETELY REDRAWN AND REVISED. CHANGE DRAWING SIZE
16 ⅝ 75 ( 75 ) 3 ( 3 ) 19 ¾ 75 ( 75 ) 3 ( 3 ) 19 ¾ 75 ( 90 ) 3 ( 3½) 19 ¾ 100 ( 130 ) 4 ( 5 ) 19 ¾ 100 ( 140 ) 4 ( 5½) 19 ¾ 115 ( 150 ) 4½( 6 )
FROM D TO C.
16 ⅝ 75 ( 75 ) 3 ( 3 ) 19 ¾ 75 ( 75 ) 3 ( 3 ) 19 ¾ 75 ( 90 ) 3 ( 3½) 19 ¾ 100 ( 130 ) 4 ( 5 ) 19 ¾ 115 ( 140 ) 4½( 5½) 19 ¾ 115 ( 165 ) 4½( 6½)

19 ¾ 90 ( 90 ) 3½( 3½) 19 ¾ 90 ( 90 ) 3½( 3½) 25 1 90 ( 115 ) 3½( 4½) 25 1 115 ( 140 ) 4½( 5½) 25 1 125 ( 165 ) 5 ( 6½) 25 1 150 ( 190 ) 6 ( 7½)

19 ¾ 100 ( 100 ) 4 ( 4 ) 22 ⅞ 100 ( 100 ) 4 ( 4 ) 25 1 100 ( 130 ) 4 ( 5 ) 25 1 125 ( 150 ) 5 ( 6 ) 25 1 125 ( 180 ) 5 ( 7 ) 25 1 165 ( 240 ) 6½( 9½)

22 ⅞ 100 ( 100 ) 4 ( 4 ) 25 1 100 ( 115 ) 4 ( 4½) 25 1 100 ( 140 ) 4 ( 5½) 25 1 125 ( 165 ) 5 ( 6½) 25 1 140 ( 190 ) 5½( 7½) 25 1 180 ( 265 ) 7 ( 10½)
TYPICAL INSTALLATION DRAWING
22 ⅞ 100 ( 115 ) 4 ( 4½) 25 1 115 ( 115 ) 4½( 4½) 25 1 115 ( 140 ) 4½( 5½) 25 1 125 ( 180 ) 5 ( 7 ) 25 1 140 ( 200 ) 5½( 8 ) 25 1 200 ( 290 ) 8 ( 11½)

25 1 100 ( 115 ) 4 ( 4½) 25 1 130 ( 130 ) 5 ( 5 ) 25 1 130 ( 150 ) 5 ( 6 ) 25 1 140 (190 ) 5½( 7½) 25 1 165 ( 230 ) 6½( 9 ) 25 1 230 ( 330 ) 9 ( 13 ) SCALE:

25 1 115 ( 115 ) 4½( 4½) 25 1 130 ( 140 ) 5 ( 5½) 25 1 130 ( 165 ) 5 ( 6½) 25 1 140 ( 200 ) 5½( 8 ) 25 1 165 ( 240 ) 6½( 9½) 25 1 255 ( 355 ) 10 ( 14 )

25 1 130 ( 130 ) 5 ( 5 ) 25 1 130 ( 140 ) 5 ( 5½) 25 1 130 ( 180 ) 5 ( 7 ) 25 1 150 ( 215 ) 6 ( 8½) 25 1 180 ( 265 ) 7 ( 10½) 25 1 255 ( 380 ) 10 ( 15 ) REVISION VALIDATION

25 1 130 ( 130 ) 5 ( 5 ) 25 1 130 ( 150 ) 5 ( 6 ) 25 1 140 ( 190 ) 5½( 7½) 25 1 165 ( 230 ) 6½( 9 ) 25 1 190 ( 290 ) 7½( 11½) 25 1 305 ( 405 ) 12 ( 16 ) THIS REVISION NO. 17 IS COVERED, FOR ALL APPROVAL AND CERTIFICATION

REQUIREMENTS, PER SAEP-334, UNDER DRAWING COMPLETION CERTIFICATE NO:

25 1 130 ( 140 ) 5 ( 5½) 25 1 130 ( 165 ) 5( 6½) 25 1 140 ( 200 ) 5½( 8 ) 25 1 180 ( 255 ) 7 ( 10 ) 25 1 205 ( 330 ) 8 ( 13 ) 25 1 320 ( 455 ) 12½( 18 )
30027516-1221-012
25 1 130 ( 140 ) 5 ( 5½) 25 1 130 ( 165 ) 5( 6½) 25 1 150 ( 215 ) 6 ( 8½) 25 1 180 ( 265 ) 7 ( 10½) 25 1 215 ( 355 ) 8½( 14 ) 25 1 330 ( 485 ) 13 ( 19 )
DESIGN CERTIFICATION REVIEW FOR KEY DRAWINGS OTHER
25 1 130 ( 150 ) 5 ( 6 ) 25 1 140 ( 180 ) 5½( 7) 25 1 150 ( 230 ) 6 ( 9 ) 25 1 190 ( 280 ) 7½( 11 ) (DESIGN AGENCY) REQUIRED (SAUDI ARAMCO)

ENGG./DATE CERTIFIED BY/DATE CONST. AGENCY/DATE OPERATIONS/DATE BY/DATE

25 1 140 ( 150 ) 5½( 6 ) 25 1 140 ( 190 ) 5½( 7½) 25 1 165 ( 240 ) 6½( 9½) 25 1 190 (290 ) 7½( 11½) MSK KMM MSK KMM
01/20/22 01/20/22 01/20/22 01/20/22
25 1 140 ( 165 ) 5½( 6½) 25 1 150 ( 200 ) 6 ( 8 ) 25 1 180 ( 240 ) 7 ( 9½) 25 1 200 ( 290 ) 8 ( 11½) REV.NO. DATE REVISION DESCRIPTION

25 1 140 ( 165 ) 5½( 6½) 25 1 150 ( 200 ) 6 ( 8 ) 25 1 180 ( 255 ) 7 ( 10 ) 17 01/18/22 UPDATE REVISION WITHOUT CHANGE

25 1 140 ( 165 ) 5½( 6½) 25 1 150 ( 215 ) 6 ( 8½) 25 1 180 ( 270 ) 7 ( 10½) JOB ORDER/EWO NO.
THIS REVISION IS NOT TO BE USED FOR
30027516 CONSTRUCTION UNTIL CERTIFIED AND DATED
25 1 150 ( 180 ) 6 ( 7 ) 25 1 150 ( 215 ) 6 ( 8½) 25 1 180 ( 270 ) 7 ( 10½)

25 1 150 ( 180 ) 6 ( 7 ) 25 1 150 ( 230 ) 6 ( 9 ) 25 1 190 ( 280 ) 7½( 11 ) SAUDI ARABIAN OIL COMPANY
DRAWING TYPE

25 1 150 ( 190 ) 6 ( 7½) 25 1 165 ( 240 ) 6½( 9½) 25 1 200 ( 290 ) 8 ( 11½) NSTALLATION OF JACK SCREWS STD
25 1 165 ( 200 ) 6½( 8 ) 25 1 165 ( 240 ) 6½( 9½) 25 1 200 ( 300 ) 8 ( 12 )
FOR FLANGED JOINTS
25 1 165 ( 200 ) 6½( 8 ) 25 1 180 ( 265 ) 7 ( 10½) 25 1 200 ( 330 ) 8 ( 13 )
STANDARD DRAWING
25 1 165 ( 200 ) 6½( 8 ) 25 1 180 ( 280 ) 7 ( 11 ) 25 1 200 ( 330 ) 8 ( 13 )
STD. DWG. SAUDI ARABIA
25 1 180 ( 215 ) 7 ( 8½) 25 1 190 ( 290 ) 7½( 11½) 25 1 215 ( 345 ) 8½( 13½)
PLANT NO. INDEX DRAWING NUMBER SHT. NO. REV. NO.
25 1 150 ( 200 ) 6 ( 8 ) 25 1 215 ( 320 ) 8½( 12½) 25 1

25 1 150 ( 215 ) 6 ( 8½) 25 1 255 ( 355 ) 10 ( 14 ) 25 1 990 L AC-036630 001 17

Saudi Aramco 2635 ENG. (05/05)

RESTRICTED VECTOR CADD-05