NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: A167 − 99(Reapproved 2009)
Standard Specification for
Stainless and Heat-Resisting Chromium-Nickel Steel Plate,
Sheet, and Strip1
This standard is issued under the fixed designation A167; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope 2.2 SAE Standard:3
1.1 This specification covers stainless and heat-resisting J 1086 Numbering Metals and Alloys (UNS)
chromium-nickel steel plate, sheet, and strip. 3. Chemical Composition
1.2 The values stated in inch-pound units are to be regarded 3.1 The steel shall conform to the requirements as to
as the standard. chemical composition specified in Table 1, and shall conform
NOTE 1—Grades that were previously covered in both Specifications to applicable requirements specified in Specification A480/
A167 and A240/A240M have been removed from this specification and A480M.
may now be supplied and purchased in compliance with Specification
A240/A240M. The chemical and mechanical property requirements of 4. Mechanical Properties
these grades were identical in Specifications A167 and A240/A240M at
iTeh
the time of removal from Specification A167.
2. Referenced Documents
Standards 4.1 The material shall conform to the mechanical properties
specified in Table 2.
2.1 ASTM Standards: (https://standards.iteh.ai)
2
A240/A240M Specification for Chromium and Chromium-
5. General Requirements
5.1 The following requirements for orders for material
Document
Nickel Stainless Steel Plate, Sheet, and Strip for Pressure
Vessels and for General Applications
Preview
furnished
cable
under this specification shall conform to the appli-
requirements of the current edition of Specification
A370 Test Methods and Definitions for Mechanical Testing A480/A480M.
of Steel Products 5.1.1 Definitions,
ASTM A167-99(2009) 5.1.2 General requirements for delivery,
A480/A480M Specification for General Requirements for
https://standards.iteh.ai/catalog/standards/sist/59d5e19b-210c-4c8e-87b5-85f77a813650/astm-a167-992009
Flat-Rolled Stainless and Heat-Resisting Steel Plate, 5.1.3 Ordering information,
Sheet, and Strip 5.1.4 Process,
E527 Practice for Numbering Metals and Alloys in the 5.1.5 Heat treatment,
Unified Numbering System (UNS) 5.1.6 Special tests,
5.1.7 Dimensions and permissible variations,
5.1.8 Workmanship, finish, and appearance,
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel, 5.1.9 Number of tests,
Stainless Steel and Related Alloysand is the direct responsibility of Subcommittee 5.1.10 Specimen preparation,
A01.17 on Flat-Rolled and Wrought Stainless Steel. 5.1.11 Retreatment,
Current edition approved May 1, 2009. Published May 2009. Originally
approved in 1935. Last previous edition approved in 2004 as A167 – 99 (2004). 5.1.12 Inspection,
DOI: 10.1520/A0167-99R09. 5.1.13 Rejection and rehearing,
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on Available from Society of Automotive Engineers (SAE), 400 Commonwealth
the ASTM website. Dr., Warrendale, PA 15096-0001, http://www.sae.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
