BRB 2 EP
GREASE
Heavy duty, multipurpose extreme pressure grease containing MoS2 solid lubricant
Applications Benefits
Use successfully for roller bearing, all types of anti- Extremely wide service temperature range of -30°C to
friction bearings, plain bearings, roller guides, threaded +130°C (up to +150°C for short intervals)
spindles, splined shafts, taper bearings, needle roller Forms a solid lubricating film to provide emergency
bearings, ball and socket joints, sliding and mating lubrication and prevents premature bearing failures caused
surfaces under vibratory or reciprocating motions, due to lubricant starvation as a film of solid lubricants is
journal bearings, couplings. always maintained between sliding surfaces
Prevents metal-to-metal contact, reduces friction and wear &
protects against fretting corrosion
For heavy duty and long term lubrication to bearings Highly resistant to hot or cold water and water washout
and equipment of heavy engineering machinery, textile Extends re-lubrication intervals and cuts down lubricant
processing machines, compressors, exhaust fans, consumption
overhead cranes, mining and construction equipment, Combination of EP additives and solid film lubricants
chassis of automotive and transportation fleet, sugar increase the load bearing capacity and provide emergency
and cement plant machinery, rolling mills. running in and boundary lubrication
Offers good surface protection and corrosion inhibiting
properties
For long lasting lubrication of cams, shafts, spring, Very good performance under moderate to high loads and
joints, steel cables; for lubrication of small gear medium speeds under reciprocating motions
mechanisms exposed to severe impact loads and slow Makes sliding smoother and reduces operational noise
operating speeds. Increases wear life of the equipment & out performs
conventional lubricants
Good resistance to oxidation
Directions for Use
Use as supplied. Never dilute or mix with other oil or grease.
Apply on all clean sliding surfaces by normal greasing
methods i.e. by brush, grease gun or dispense via centralized
lubrication systems.
SPECIALIZED LUBRICANTS Supersedes previous data. Data is subject to change per latest
MRO TECHNICAL & CHEMICALS advances without notice. For safety data sheets (SDS) contact
FOR HIGH PERFORMANCE & DEPENDABLE SOLUTIONS sds@asvmultichemie.com
BRB 2 EP
GREASE
TECHNICAL PROPERTY
Parameter Value Unit Standard
Type Grease with EP/AW additives and solid lubricants
Appearance Smooth grease
Base oil Mineral
Base oil viscosity, @ 40°C 110 mm2/s DIN 51 562
Thickener Lithium
Color 1 Black
Penetration, worked 265-295 mm/10 ASTM D 217
NLGI consistency 2 Class DIN 51 818
3
Density, @ 25°C 0.85- 0.95 g/cm
Drop point +185 °C ASTM D 566
Service temperatures -30 to +130(+150 for short periods) °C
Speed-DN value2 450,000 mm/min
SKF-Emcor corrosion test 0-0 DIN 51 802
Four ball wear test, weld load 3600 N DIN 51 350 pt.4
Four ball wear test, wear scar, 800N < 0.85 mm DIN 51 350 pt. 5
Oxidation resistance, pressure drop, 0.1 bar DIN 51 808
100h, 100°C
Oil separation, standard test <4 % DIN 51 817
1. Minor color variation of the same product but of different batches could be possible. However the lubrication values remain unchanged.
2. Values will differ as they are largely dependent on operating temperatures, loads and type of bearing.
General Available Packaging
Use in well ventilated areas. Avoid continuous breathing of 1 kg, 5 kg, 20 kg, 180 kg
vapor and spray mist. In closed areas or areas with poor
ventilation, use respiratory protection. For complete details on Shelf Life
safety, short and long term exposure, refer to this product’s 36 months from date of manufacture in sealed condition.
safety data sheet (SDS).
Limited Warranty
Disposal The information and data contained in this sheet is accurate
All used and unused product should be disposed of in to the best of our knowledge or is obtained from sources, tests
accordance with state regulations. or experiences believed by us to be reliable and accurate.
User is responsible for determining whether recommended
Handling ASV product is fit for a particular purpose. All products should
Read instructions on the container label of the product before be tested for suitability on a particular application prior to
use. The product safety data sheet (SDS) contains the relevant actual use. We make no representations of any kind. Data
information regarding personal protective equipment, safe offered without warranty. Product manufactured is for
use, physical and health hazards. Safety data sheet is industrial use only.
available from ASV or your local ASV distributor.
Manufactured by WWW.ASVMULTICHEMIE.COM
ASV Multichemie Private Limited
W 46, TTC Industrial Area, MIDC Rabale, ASV® MOLYSULF® PENETROIL® SHINY GALVA® VALV-KOTE® BRIGHT ZINK®
Navi Mumbai 400 701 INDIA SPEZET® MOLYCHEM® TRIBOSULF® are Registered Trademarks of ASV MULTICHEMIE
Contact: +91 22 2764 2516 PRIVATE LIMITED, INDIA.
Email: info@asvmultichemie.com ALL DATA OFFERED WITHOUT LIABILITY OR WARRANTY.
