Republic of the Philipinnes

Department of Education
CORDILLERA ADMINISTRATIVE REGION

PROJECT SMART (Standardized and Meaningful Assessment Result-based Teaching

Table of Specification in Carpentry 7

Grade:7 Quarter: First

Question Intent
Type of No. of Item
Learning Code Cognitive Process Dimension
Test Items Placement
Competency Remembering Understanding Applying Analyzing Evaluating Creating
Identify tools and TLE_IACP7/8UT-0a- Multiple-
12 1-12
materials for a task 1 choice
Request appropriate TLE_IACP7/8UT-0b- Multiple-
10 13-22
materials and tools 2 choice
Check condition of TLE_IACP7/8MT-0c- Multiple-
10 23-32
tools and equipment 1 choice
Perform basic TLE_IACP7/8MT-0c-
Multiple-
preventive 2 10 33-42
choice
maintenance
Select measuring TLE_IACP7/8MD- Multiple-
10 43-52
instruments 0d-1 choice
Carry out TLE_IACP7/8MC-
Multiple-
measurement and 0d-e-2 10 53-62
choice
calculation
Analyze signs, TLE_IACP7/8ID-0f-1 Multiple-
10 63-72
symbol, and data choice
Interpret technical TLE_IACP7/8ID-0f-2 Multiple-
10 73-82
drawings and plans choice
Apply freehand TLE_IACP7/8ID-0g- Multiple-
10 83-92
sketching h-3 choice
Identify hazards and TLE_IACP7/8ID-0i-1 Multiple-
10 93-101
risks choice
 Republic of the Philipinnes
Department of Education
CORDILLERA ADMINISTRATIVE REGION

Prepared by:

SONNY GAWILAN
Test Writer

Reviewed by:
MAYNARD D. BAGABAY
Reviewer
 Republic of the Philipinnes
Department of Education
CORDILLERA ADMINISTRATIVE REGION

FIRST QUARTER TEST IN CARPENTRY 7

_____1. Teacher Ferrer wants to check the vertical alignment of the column of the newly constructed school canteen, which of the following tools is
appropriate for the task?
A. Level bar
B. Level hose
C. Plumb-bob
D. Steel square
_____2. You want to cut lumber across the grain. Which tool should you use for the task?
A. Back saw
B. Crosscut saw
C. Hack saw
D. Rip saw
_____3. A carpenter wants to fasten and remove nails. Which tool is appropriate?
A. Ball-pen hammer
B. Claw Hammer
C. Rubber mallets
D. Sledgehammer
_____4. A carpenter wants to smoothen wood surfaces. Which tool should he use?
A. Chisel
B. File
C. Plane
D. Sandpaper

_____5. A carpenter wants to know the angle of the beam of the reading kiosk. Which tool is appropriate?
 Republic of the Philipinnes
Department of Education
CORDILLERA ADMINISTRATIVE REGION

A. Combination Square
B. Level
C. Marking gauge
D. Protractor
_____6. What specific carpentry material should I buy to make the door swings when you close and open?
A. Door hinge
B. Doorknob
C. Door lock
D. Door shutter
_____7. A carpenter wants to obtain vertical line. Which tool is appropriate?
A. Plum bob
B. Pull push rule
C. Ruler
D. Spirit level
_____8. Mang Ambo wants to check Angles of the corners of the door. Which tool is appropriate?
A. Plumb bob
B. Ruler
C. Spirit level
D. Try square
_____9. if you will check the flatness of the ironing board which tool is appropriate on the task?
A. Plumb bob
B. Ruler
C. Spirit level
D. Try square
____10. What tools will Mang Ambo will use if he scribes clock on their divider.
A. Plumb bob
B. Ruler
 Republic of the Philipinnes
Department of Education
CORDILLERA ADMINISTRATIVE REGION

C. Spirit level
D. Try square
____11. Architectural drawings are not drawn full size. Which is used to allow the building views to be drawn on a smaller paper?
A. Measuring tape
B. Pencil
C. Ruler
D. Scale
____12. Which tool is often kept on a carpenter’s belt and used to take measurements?
A. Chalk line
B. Pull push rule
C. Speed square
D. T-belt
____13. Mr. Ferrer wants to paint the ceiling of his office, what are the materials should he request for the job?
A. Pail, paint, paint brush
B. Paintbrush, paint, paint pan
C. Paint, Paint roller, Paint pan
D. Paint container, paint roller
____14. Mila is planning to acquire materials for her cabinet. In what part of the requisition form does she indicate this project?
A. Balance on hand
B. Date
C. Suggested project
D. Total
____15. Vinz wants to have 5 liters of paint in his suggested project. In what part of the requisition form is liters written?
A. Balance on hand
B. Materials and description
C. Requisition unit
D. Total
 Republic of the Philipinnes
Department of Education
CORDILLERA ADMINISTRATIVE REGION

____16. Which entries of the requisition form should be written next to the suggested project?
A. Balance on hand
B. Date of requisition
C. Materials and description
D. unit price
____17. You want to apply varnish on wood surfaces? What items will you request to the supply officer?
A. Paint brush and varnish
B. Paint pan and varnish
C. Screwdriver and paint brush
D. Thinner
___18. Which is the sixth step in accomplishing the requisition form?
A. Write your name as a requisitioner.
B. Write the number of required materials.
C. List the unit of materials to be requisitioned.
D. State the name of the project and date when you requested for materials.
____19. What is the next step after listing the unit of materials to be requisitioned?
A. List the cost per unit and the total cost.
B. List the unit of materials to be requisitioned.
C. Enumerate the materials with their description.
D. Fill in the classification of the project and its purpose.
____20. Which is the 7th step in accomplishing the requisition form?
A. Write your name as requisitioner.
B. Write the number of required materials.
 Republic of the Philipinnes
Department of Education
CORDILLERA ADMINISTRATIVE REGION

C. Secure the approval of the supply officer.

D. List the unit of materials to be requisitioned.
____21. Which is the second step to consider in accomplishing the requisition form?
A. Write your name as requisitioner.
B. Write the number of required materials.
C. List the cost per unit and the total cost.
D. Enumerate the materials with their description.
____22. Which is the fourth step involved in requesting materials and tools?
A. Write your name as requisitioner.
B. List the cost per unit and the total cost.
C. Write the number of required materials.
D. Enumerate the materials with their description.

____23. Teacher Tomy instructed Tony to finish his project, but he finds out that some of the tools needed on the task are defective, if you were Tony
what should you do.
A. Get and bring at your home and let your dad fix them.
B. Label the tools that are defective and report to teacher Tomy.
C. Get the tools and fix since you are capable in repairing tools.
D. Use the tools if still usable since teacher Tomy was not around.
____24. As a carpentry student what will you recommend to a carpenter to ensure safe use of tools.
A. Verify, fix, record,
B. Inspect, check, verify
C. Repair, inspect, check
D. Segregate, inspect, check
____25. What will you do when you discover a tool that has been damaged?
A. Dispose it
B. Do not use it
 Republic of the Philipinnes
Department of Education
CORDILLERA ADMINISTRATIVE REGION

C. Use it carefully
D. Purchase another form
____26. Which of the following does the carpentry maintenance do?
A. Assist in repairing tools
B. Assist in bending metals
C. Cuts and shapes materials
D. Assist in measuring and marking

____27. Which of the following is the correct sequence in Segregating and Labeling Non-functional Tools and Equipment?
1. Conduct an inventory of tools and equipment.
2. Record the number of non-functional tools and equipment.
3. Segregate tools that are serviceable or unserviceable.
4. Report the number of tools and equipment that are non-functional but subject for repair.
5. Label tools and equipment which are condemnable. 6. Return tools and equipment in the tool cabinet as per operating procedures.
A. 1, 2, 3, 4, 5
B. 5. 4, 3, 2, 1
C. 3, 4, 5, 1, 2
D. 1, 2, 5, 4, 3
____28. What should you do before using newly procured powered hand tools?
A. make sure that power is working.
B. Make sure no one is sitting near you.
C. Try to use the tools until you mastered.
D. Ensure that you have been properly trained to use the tool safely.
____29. What should you do if you find a tool defective?
A. Just set aside
 Republic of the Philipinnes
Department of Education
CORDILLERA ADMINISTRATIVE REGION

B. Throw in the proper trash can.

C. Tag it clearly “Out of service for repair”.
D. Get and sell to buyers of bottles and steel so that no one can use it.
____30. How should you inspect powered hand tools?
A. Just count the items.
B. Just see if they are faded.
C. Just see if they are complete.
D. Inspect each tool for any damage prior to each use.
____31. Which of the following is the indication that chisel is defective?
A. Chisels are very sharp.
B. The chisels look like antique.
C. The chisels have mushroomed heads.
D. The paint of the handles of the chisels are faded.
____32. What will you do to check the condition of the different Personal Protective Equipment?
A. Report the condition or status of PPE.
B. Repair/replace the non-functional PPE.
C. Separate the non-functional and functional PPE.
D. Inspect any damaged or defective Personal Protective Equipment (PPE).

___33. What will you use if you want to lubricate bearings gaskets seals and other moving parts?
A. Cooking oil
B. Grease
C. Soap
D. Water
___34. What will be the best way to keep the tools in good condition?
A. Clean
B. Remove
 Republic of the Philipinnes
Department of Education
CORDILLERA ADMINISTRATIVE REGION

C. Separate
D. Throw
___35. What substance will you use if you want to minimize friction especially in carpentry tools with thread like pliers?
A. Cooking oil
B. Grease
C. Soap
D. Water
___36. What will happen to your carpentry tools if you do not maintain it by lubricating?
A. it will add cost to the tools
B. your tools do not perform well in its work
C. tools can perform faster and accurately
D Application of lubricant will cause formation of rust to the metal parts of the tools.

____37. Which in the following is a good practice in using hammer?

A. John use another hammer to strike stones.
B. Diego use the cheek of the hammer in driving nails
C. Ambo use a claw hammer for pulling nails and driving nails
D. Lucas use the hammer in driving nails even his hands are oily and greasy
___38. What will you do if you find out that the electric plainer is defective?
A. Repair
B. Get and hide it
C. Let the teacher know the next day
D. Attach an Out of Service tag with signature and date.
___39. Which maintenance activities does preventive maintenance include?
 Republic of the Philipinnes
Department of Education
CORDILLERA ADMINISTRATIVE REGION

A. Predictive and planned maintenance activities.

B. Periodic, predictive and planned maintenance activities.
C. Periodic, predictive and unplanned maintenance activities.
D. Periodic, unpredictive and planned maintenance activities.
____40. What action can be carried out to retain an item or to restore its functional condition?
A. Installation
B. Maintenance
C. Repair
D. Segregation
____41. What should a carpenters’ do to prevent corrosion?
A. Lubricate the tools regularly.
B. Wipe the tools regularly.
C. Wash with soap the tools every day.
D. Soaked the tools in water when not in use.
____42. What will you do to keep your tools and equipment free from dust and dirt while they are not being used?
A. Lubricate your tools.
B. Keep your tools scattered in the storage room.
C. Cover with blanket your tools while they are not being used.
D. Keep your electric tools stored in their original cases and containers.

____43. You need to mark a line on a floor that is to be 10 meters (32’ 10”). Which is the best layout tool to use?
A. Caliper
B. Pull-push-rule
C. Tape measure
D. Try square
____44. A carpenter wants to measure long distances. Which tool is appropriate?
 Republic of the Philipinnes
Department of Education
CORDILLERA ADMINISTRATIVE REGION

A. Extension rule
B. Meter stick
C. Pull push rule
D. Ruler
____45. You want to scribe arcs and circles in your project. Which tool is appropriate?
A. Caliper
B. Compass
C. Pencil
D. Ruler
____46. Teacher Mario wants to measure the diameter of the pipes. What tool should he get to do the job?
A. Caliper
B. Compass
C. Pencil
D. Ruler
____47. If you are taking measurements on a very tight space. Which tool is appropriate?
A. Caliper
B. Compass
C. Pencil
D. Zigzag rule

___48. What do you call a linear measuring instrument used to measure angles of an object?
A. Protractor
B. Meter stick
C. Ruler
D. Push-pull rule
 Republic of the Philipinnes
Department of Education
CORDILLERA ADMINISTRATIVE REGION

____49. What tool would you use to measure the height of the flagpole?
A. Caliper
B. Pull-push-rule
C. Tape measure
D. Try square
____50. What measuring instrument would you use to measure the circumference of a round log?
A. Caliper
B. Pull-push-rule
C. Tape measure
D. Try square
____51. Mr. Tan wants to measure the length of the corrugated G.I sheet. which tool is appropriate?
A. Caliper
B. Pull-push-rule
C. Tape measure
D. Try square
____52. Teacher Mario wants to know the length of the steel bar. What measuring instrument would you give to do the task?
A. Caliper
B. Pull-push-rule
C. Tape measure
D. Try square
____53. If the price of narra is Php 20.00 per boardfoot, How much should i pay if i will buy 20 boardfeet of narra?
A. Php 400.00
B. Php 4,000.00
C. Php 40,000.00
D. Php 400,000.00
____54. How many board feet in a piece of narra that is 2” thick, 6” wide,12’ long?
 Republic of the Philipinnes
Department of Education
CORDILLERA ADMINISTRATIVE REGION

A. 12 Board feet
B. 13 Board feet
C. 14 Board feet
D. 15 Board feet
____55. Sotina purchased 2 pcs of narra board that is 1” thick, 12” wide, and 4’ long. The price is Php. 55.00/board foot. How much
did Sotina pay?
A. Php 4.400
B. Php 44.000
C. Ph 440.00
D. Php 440.00
____56. Which of the following would equal to one board foot??
A. 1” x 12” x 1’
B. 1” x 12’ x 1’
C. 1’ x 12” x 1’
D. 1” x 12” x 1”
____57. To figure the cost of your project, you should multiply your board foot amount by:
A. the length of the board.
B. the cost of the finished project wood.
C. the price per board foot of the type of wood you choose to use.
D. the cost of your project.
___58. Determine the number of board feet in a piece of Mahogany that is 1” thick, 4” wide, and 72” long?
A. 2 BD
B. 2 CM
C. 2 DM
D. 2 M
___59. A Carpenter bought 5 pcs 2” x 3” x 10’ lumber. What is the total volume of the lumber that he bought?
 Republic of the Philipinnes
Department of Education
CORDILLERA ADMINISTRATIVE REGION

A. 5 board feet
B. 5 square feet
C. 5 square meter
D. 5 square decimeter
____60. What is the total length of five wooden post if the length of each post is 10 feet.
A. 50 Ft.
B. 50 Cm.
C. 50 M.
D. 50 Km.
____61. If the total length of wooden post for the construction of reading kiosk is 20 feet. How many wooden post we need to
provide if the length of each post is 5 feet?
A. 4 meters
B. 4 yards
C. 4 quarter
D. 4 pieces
____62. What is the meter equivalent of 300 centimeter?
A. 3 cm.
B. 3 dm.
C. 3 m.
D. 3 mm.

_____63. What line will I used to indicate alternate position of the parts of an object, repeated detail, or the location of absent parts?
A. Phantom line
 Republic of the Philipinnes
Department of Education
CORDILLERA ADMINISTRATIVE REGION

B. Section Lines
C. Short Break Line
D. Long break line
_____64. What line will you use to indicate the part of an object being removed?
A. Phantom line
B. Section Lines
C. Short Break Line
D. Long break line
_____65. There are six principal views of an object; the top view, the front view, right side view, left side view, bottom view, and the rear views.
Which of these views are accepted by the industry as standard multi-views according to the 3 rd angle projection?
A. Front view, rear view, side views
B. Top view, front view, and right-side view
C. Right side view, left side view and bottom views
D. Right side view left side view, and bottom views.
_____66. What type of line will Mrs. Panti will use to show the edges and contours of the object that she wants to emphasize to her audience?
A. Dimension line
B. Extension Lines
C. Hidden Line
D. Visible line
_____67. What type of line will be used to indicate direction of sight when a partial view is used?
A. Dimension line
B. Hidden Line
C. Viewing plane line
D. Visible line
_____68. What type of line will you use if you want to convey measurement?
A. Dimension line
B. Hidden Line
 Republic of the Philipinnes
Department of Education
CORDILLERA ADMINISTRATIVE REGION

C. Viewing plane line

D. Visible line
_____69. What appropriate line will be utilized to show surfaces, edges, or corners of an object that are hidden from view?
A. Dimension line
B. Hidden Line
C. Viewing plane line
D. Visible line
_____70. What do call a thin line used to indicate alternate position of the parts of an object, repeated detail, or the location of absent parts.
A. Dimension line
B. Hidden Line
C. Phantom line
D. Viewing plane line
_____71. What alphabet of line will I used to reduce the size of the drawing of a long part having uniform cross section so that it can be shown on a
smaller sheet?
A. Dimension line
B. Hidden Line
C. Phantom line
D. Short-break line
____72. It indicates the part or area of a drawing to which a number, note, or other reference applies.
A. Dimension line
B. Hidden Line
C. Leader line
D. Short-break line
 Republic of the Philipinnes
Department of Education
CORDILLERA ADMINISTRATIVE REGION

Specifications
• Sides - 2pcs. 1” x 12” x 3 ft
wood (mahogany)
• Shelves - 2 pcs. 1” x 12” x 2 ft
• Top- 1 pc. 1” x 12” x 2 ft
• Joints must be miter and dado

Front view Right side view

____73. Base on the given work plan what is the height of the bookrack?
A. 3 feet
 Republic of the Philipinnes
Department of Education
CORDILLERA ADMINISTRATIVE REGION

B. 4 feet
C. 5 feet
D. 6 feet

____74. If you look to the work plan what is the width of the bookrack?
A. 12 inches
B. 14 inches
C. 18 inches
D. 20 inches
____75. What do you call on the 2 pcs parts of a bookrack that are fixed vertically at the side?
A. Bottom shelf
B. Center shelf
C. Side frame
D. Top
____76. This is a joint used in assembling bookrack.
A. Builds joint
B. Miter and dado joints
C. Mortise and tenon
D. Lap point
____77. These are parts of the bookrack which are installed at the center and bottom horizontally.
A. Brace
B. Frame
C. Shelf
D. Top
____78. It is a view of a working plan showing the upper portion of the object to be done.
A. Back view
 Republic of the Philipinnes
Department of Education
CORDILLERA ADMINISTRATIVE REGION

B. Front view
C. Right side view
D. Top view
____79. A view of the working plan showing the front portion of the project.
A. Back view
B. Front view
C. Right side view
D. Top view
____80. What is the distance between each shelf?
A. 16 feet
B. 16 inches
C. 16 meters
D. 16 yards
____81. Base on the plan how many 1” x 12” x 3’ lumber do we need to assemble the bookrack?
A. 2 boardfeet 1” x 12” x 3’ lumber
B. 2 inches 1” x 12” x 3’ lumber
C. 2 meters 1” x 12” x 3’ lumber
D. 2 pieces 1” x 12” x 3’ lumber
____82 What is the width of the bookrack?
A. 2 feet
B. 2 inches
C. 4 meters
D. 5 yards

Apply freehand drawing

___83. Which of the following is an isometric box?
 Republic of the Philipinnes
Department of Education
CORDILLERA ADMINISTRATIVE REGION

A. B. C. D.

____84. Which of the following is an orthographic drawing?

A. B. C. D.

____85. Tom wants to sketch an isometric box, what will be his first step?
A. Sketch an isometric box
B. Determine the length and width of the box.
C. Draw right and left axis, a straight, inclined line emanating from the vertical axis
D. Measure the height of these vertical lines and mark the desired height of your sketch.
____86. Why it is dimensioning sketches is an acceptable practice? It gives
A. emphasis to the object
B. the size and shape of the object.
C. important information concerning the drawing.
D. the size and location of holes, and other important shapes
____87. What is the most important element in drawing a good sketch?
A. Drawing round circles.
B. Keeping the sketch proportional.
C. producing good line work.
D. producing good output.
 Republic of the Philipinnes
Department of Education
CORDILLERA ADMINISTRATIVE REGION

_____88. What is a good method of proportioning a sketch?

A. Cutting out a template
B. Using a graph paper
C. Using a compass and scale
D. Projecting an image on a wall.
_____89. Which three items are needed to complete a sketch?
A. Paper, red pen, eraser
B. Straight edge, paper, pencil
C. Paper, pencil, eraser
D. Compass, straight edge, pencil
____90. What is the primary purpose of sketching?
A. So that parts can be manufactured.
B. No one sketches because it is all done on computers.
C. So that we do not have to make technical drawing.
D. Get ideas on paper quickly and communicate ideas with others.
____91. It is made without the use of drawing instruments or straight edges?
A. Designing
B. Curving
C. Free hand drawing
D. Lettering
____92. It refers to process of making the visible surfaces of an object, drawn in outline form?
A. Accented outline
B. Highlighting
C. Shading
D. Shadowing
___93. Which situations below results when hazards and risks are identified?
 Republic of the Philipinnes
Department of Education
CORDILLERA ADMINISTRATIVE REGION

A. You become unproductive.

B. You work efficiently and effectively.
C. There is a discomfort while working.
D. Safety is not ensured when working.
____94. Marco works in the shop with nails and sharp objects scattering on the floor. Which hazard is present in the working area?
A. Falling objects
B. Harmful dusts
C. Objects that can puncture the skin
D. Radiation
____95. Which of the following may occur if loud noise in the workplace is NOT controlled?
A. Blindness
C. Damage to the joints
B. Hearing damage
D. Skin irritation

____96. Why are safety shoes important in doing carpentry-related work?

A. They protect the hands from cuts.
B. They make the workplace less noisy.
C. They protect the feet from wire tacks, nails, and scrap metals.
D. They protect the eyes from flying particles and other materials.
_____97. Which of the working conditions below can produce hazards?
A. Falling objects
C. Well ventilated workplace
B. Safe working environment
 Republic of the Philipinnes
Department of Education
CORDILLERA ADMINISTRATIVE REGION

D. Well lighted workplace

____98. Poor ventilation in the workplace can produce hazard and risk that may harm the workers. Which hazards below is described by the
statement?
A. Heat
C. Falling objects
B. Radiation
D. Toxic chemical
____99. Dust and other solid particles are scattered in the working area due to strong winds. Which is the effect of this situation?
A. It may result to bone fracture.
B. It may result to muscle damage.
C. It leads respiratory system irritation.
D. It has no bad effects to health at all.
____100. When someone identifies hazards and risks in the workplace, which is likely to happen?
A. Accidents occur.
C. Accidents are avoided.
B. Workers cannot work well
D. Workers can work confidently.
___101. Which should be the initial step to identify hazards?
A. Survey the workplace.
B. Reassess when new equipment is instilled.
C. Organize the materials properly in a proper area.
D. Determine whether personal protective equipment should be used.