User Manual X-K17B
Kinetic Ring
This manual contains important information. Please read before operating fixture.
1. TEAR OFF THE PACKAGE <<<
Thank you for choosing to use our kinetic lights. In order to use
this product correctly and safely, please read the instructions carefully
before installing and using this product. This manual contains important
installation and application information. When installing and operating
the product, please strictly follow the operating steps of the manual.
Our system uses a new and beautiful high-hardness metal body
with High temperature resistant design. The system is designed and
produced strictly in accordance with CE standards. It conforms to the
international standard DMX512 signal . It can be used alone or on-line
use. It has the feature of fast speed, low noise, and powerful functions.
It is suitable for small and concerts, theaters, Studios, nightclubs,
bars and other places.
2. SAFETY INSTRUCTIONS <<<
Note: Please be cautious before operating this product. The product
is a high-voltage product. If you touch the wire, you may get an electric
shock! This product is intact before leaving the factory. To keep the
product in good condition and ensure safe operation, users should
follow the safety matters and the warnings in this manual.
IMPORTANT
Damage caused by dont following this manual is not covered by
the warranty.If the product has been exposed to an extremely unstable
temperature environment (such as after transportation), please do not
immediately connect the product to the power supply, because the
water droplets generated due to temperature changes may damage
the product. Please use the product after returning to normal
temperature.
This product can be used in the voltage range of 90-240V and
for indoor use. Please ensure that the voltage is not higher than the
product's acceptable range! ! The power plug must be plugged into
a protective Class I socket.
Please check the power cable of this product frequently to ensure
that the power cable is not folded/ damaged /scratched. And do not
connect with other cables! Pay special attention when connecting the
power cable.
Before using the product, please familiarize yourself with the
operating functions of the product. Unprofessional operation may
cause short circuit, burns or electric shock. Please do not let children
or unprofessionals touch the product.
Please do not modify this product without authorization, other
wise the product may be damaged, so the damage caused is not
covered by the warranty.
NOTE: Our company will not bear any responsibility for all the
consequences caused by the fall of the light fixture due to unstable
and unsafe installation.
3.OPRATE INSTRUCTIONS <<<
The schematic diagram of the winch panel is as shown in the
figure above. The top title displays the name of the light, and the
bottom is the status , which displays the current fixture signal, fixture
status, fault (when there is no fault information, it will display "ERR",
other wise it will display "NOR") .This winch supports DMX/RDM
protocol. When the winch is searched by the RDM host, the "RDM"will
appear on the panel, indicating that the lamp is enumerated normally.
The display and operation are similar to the "Android operating
system", just click the corresponding item with your fingertips to operate.
Note: Do not use pointed or sharp objects to click on the display to
prevent damage.The screen supports both Chinese and English.Enter
the corresponding parameter setting.Shown in the below. The specific
menu content is shown in below table:
DISPLAY
Set the displayed language
Language English English display
中文 Chinese display
Set the display content or method of the
screen after no operation within 30 seconds
Close Keep the last operation page, bright screen
Mode 1 Screen off
Screen Saver
Black screen, display the address code of the
Mode 2
current fixture in the lower left corner
Display brand information, address code and
Mode 3
operating mode
Set the display direction of the screen
Close Do not reverse the display
Screen Rot Open Reverse display
Automatically detect the direction of the hanging
Automatic fixture, automatically switch the display direction
Set the indication mode of DMX signal indicator
On / when there is a signal,
Mode 1 off / when there is no signal
DMX Indicate Off / when there is a signal,
Mode 2 On / when there is no signal
Flashing / when there is a signal,
Mode 3 off / when there is no signal
1~10 10 levels
Set the brightness of the screen backlight after 10 seconds
Screen Light of no operation, and it will be all on during operation
1~10 10 levels
4.CHANNAL LIST <<<
The order of the channel can be viewed in the scene mode. The channel mode is set in
the "Address Setting" page. The specific details are shown in the following table:
8CH
CH NAME VALUE SPECIFICATION
1 Lifting height 000-255 Adjust the height of the lift
Fine adjustment
2 000-255 Fine-tuning
of lifting height
3 Lifting speed 000-255 From fast to slow
4 Dimmer 000-255 0-100%dimmer
000-255 0-14 Blank
5 Effect
015-255 Change one effect after number 5
000-127 Clockwise effect from fast to slowly
6 Effect speed
128-288 Anticlockwise effect from slowly to fast
000-004 Dimmer
7 Strobe
005-255 Slowly to Fast
8 Reset 251-255 After 6S reset
80CH
CH NAME VALUE SPECIFICATION
1 Lifting height 000-255 Adjust the height of the lift
Fine adjustment
2 000-255 Fine-tuning
of lifting height
3 Lifting speed 000-255 From fast to slow
4 Dimmer 000-255 0-100%dimmer
000-255 0-14 Blank
5 Effect
015-255 Change one effect after number 5
000-127 Clockwise effect from fast to slowly
6 Effect speed
128-288 Anticlockwise effect from slowly to fast
7 Red 1 000-255 0-100%dimmer
8 Green 1 000-255 0-100%dimmer
9 Blue 1 000-255 0-100%dimmer
10 Red 2 000-255 0-100%dimmer
11 Green 2 000-255 0-100%dimmer
12 Blue 2 000-255 0-100%dimmer
--- --- --- ---
CH NAME VALUE SPECIFICATION
76 Red 24 000-255 0-100%dimmer
77 Green 24 000-255 0-100%dimmer
78 Blue 24 000-255 0-100%dimmer
000-004 Dimmer
79 Strobe
005-255 Slowly to Fast
80 Reset 251-255 After 6S reset
5. INSTALLATION <<<
Step 1 Step 2 Step 3
Connect the clamp Hang the winch on Connect the light
to the winch the truss fixture to the winch
6. WARNING <<<
Please keep sufficient safety distance and lifting distance during
installation Adequate safety distance must be considered during
installation Otherwise the light fixture will touch the ground or objects,
causing product damage
7. TECHNICAL SPECIFICATIONS <<<
Three winch+ one Led ring
Operate Voltage AC90-240V 50/60Hz
Power 300W
Control Channel 8/80CH
Control Model DMX512, MADRIX
Work permit temperature -5-45 degree
Light source 150PCS RGB SMD LEDS
Classic 5.6kg
G.W 7.0kg
LED viviparid size D80cm
8. MAINTENANCE AND CLEANING <<<
The following points must be considered during the inspection:
1. The screws used to install equipment and equipment parts must be tightly
connected and must not be corroded
2. The fixed point and installation point (ceiling/truss) shall not be deformed
3. The mechanically moved parts must not show any signs of wear
4. The power cord shall not be damaged in any way
5. The installer must follow the operating instructions and the actual situation of
the site to formally install it to eliminate any safety hazards
6. Clean the inner and outer spheres every week to avoid insufficient lighting
caused by dust accumulation.
7. Clean the fan weekly
8. Every three months, electrical engineers conduct detailed inspection and
maintenance of the product to ensure that the circuit contacts are good,
9. Avoid poor circuit contact and cause overheating
10. Do not use alcohol and solvents for cleaning
11. If you need any spare parts, please order genuine products from your
local dealer
