Samarth Rural Education Institute

SAMARTH POLYTECHNIC BELHE

Approved by AICTE, New Delhi & Govt. of Maharashtra, Affiliated to MSBTE,
Mumbai & MSBTE Institute Code-0992, DTE Code No. D6451
A/P- Belhe, Tal- Junnar, Dist.- Pune, Pin-412410, Mob. 9766303701
Email ID- 0992principal@msbte.com Web- www.poly.sreir.org
Department Of CO/CE
Programme Name: CO/CE Programme Code: CO/CE
Course Name: Management Course Code: 22509
Important Questions
Unit-IV
Safety Management
Q.
Questions
No.
Safety Programmes is a continuous process to achieve adequate
a) Profit
1 b) Sales
c)Safety
d)Loss
Four Es of Safety________.
a) Engineering, Education, Enlistment, Enforcement.
2 b) Engineering, Education, Enlistment, Environment.
c) Environment, Education, Enlistment, Enforcement.
d) Engineering, Economic, Enlistment, Enforcement.
Which equipment is used for protection of lungs?
a) Hard Hats
3 b) Shields
c)Gas Masks
d)Apron
Electrical insulation should be tested_______.
a) Frequency
4 b) Monthly
c) Periodically
d) Daily
Repair work should be done after switching the_________.
a) Power on
5 b) Power off
c) Shut down
d) All of the above
You should wear eye, head and face protection if you are working with which of
the following tools_________.
a) portable abrasive wheel tools
6
b) Electric tools
c)Pneumatic tools
d)Liquid fuel tools
The most dangerous place to use electrical equipment’s is___________.
7 a) Near a ladder
b) Outdoors
 c)Near water
d)Near other electric equipment’s
Which equipment is used for protection of eyes?
a) Face mask
8 b) Goggles
c)Gas mask
d)Asbestos clothing
One way to learn to operate your equipment properly and safely is to read.
a) safety datasheet
9 b) Manufacturer’s instructions
c)OSHA’s general duty clause
d)none of above
Safe and proper equipment operation generally includes
a) Inspection and maintenance
10 b) Warming it up
c)Knowing how to contact emergency
d)All of above
Industrial safety management if that branch of management which is
concerned with ______ hazards from the industries.
a) Reducing
11
b) Controlling
c)Eliminating
d) All of the above
The following is(are) physical hazard agent(s)_______.
a) Falls
12 b) Inhalation
c) Electricity
d) All of the above
Which device is used to push material into the cutting area.
a) Push Button
13 b) Push Stick
c) Push Bar
d) None of Above
First aid is___________.
a) Temporary and immediate care given to the victim
14 b) Permanent care given to victim
c) Both a and b
d) Neither a nor b
Which of the following precautions is/are necessary in electrical work?
a) The equipment’s should be earthed properly
15 b) Cable should be completely insulated
c) Cable should have any joints
d) Both a and b
SMS Mean___________.
a) Safety management society
16 b) Safety Management System
c) Safety Moving System
d) None of above
 Long form of PPE ________.
a) Personal Productive Equipment
17 b) Production Planning Engineering
c) Personal Protective Equipment
d) None of above
If you wanted to convey the most severe type of hazard, which word would you
use?
a) Warning
18
b) Notice
c) Danger
d) Caution
Safety promotes____________.
a) Sales
19 b) Productivity
c) Research
d) Profit
Which of the following is not concerned with general safety norms_________.
a) Perform Job Safely
20 b) Follow rules and regulation
c) Incident not reported to supervisor
d) Eliminate fire hazards.
SOP means
a) Safe operating procedure
21 b) Standard operating Process
c) Safe operation procedure
d) Standard operation policy
Safe operating procedure is revised.
a) No
22 b) Yes
c) Can’t say
d) None of these
Who is responsible to take care of health and safety of worker?
a) Worker
23 b) Safety committee
c) Manager
d) All of above
SOP is a___________document.
a) Oral
24 Written
c) None of above
d) Visual
Who ensure to follow safe procedure?
a) Employers
25 b) Workers
c) Managers
d) All of the above
Issue means___________.
26
a) Pre job check
 b) Post job check
c) During Job check
d) None of Above
In permit to work system a document is_________.
a) Oral
27 b) Written
c) Visual
d) None of these
Confined space includes___________.
a) Storage bins
28 b) Silos
c) Tanks
d) Grounds
Inspection is an example of__________.
a) Hot work permit
29 b) Cold work permit
c) Electrical permit
d) Ground disturbance permit
In work permit system, who is responsible for keeping area and staff safe?
a) Issuer, Executer, Field operator
30 b) Manager, Engineer, Worker
c) Supervisor, Officer, Engineer
d) None of the above
_______ is a sudden and unfortunate happening which causes damage or loss of
property, material or human.
a) Accident
31
b) Activity
c) Process
d) Movement
General causes of accidents are as follows
a) Accidents due to dangerous machines
32 b) Unsafe physical conditions
c) Moving objects
d) All of the above
Which of the following may be the cause of accident?
a) Overconfidence of the employee
33 b) Proper training
c) Sound knowledge
d) None of the above
Taking shortcuts and lack of adequate knowledge are causes of accidents
because of ________.
a) Workers
34
b) Management
c) Faculty layout
d) Natural disaster
Why should near misses be reported?
35 a) To educate employees
b) To test the first aider
 c) To ensure complete recovery
d) To stop a more serious event occurring
An accident is________.
a) An unsafe act
36 b) An unsafe condition
c) Unplanned, something that happens by chance
d) None of the above
I can help prevent accidents by_________.
a) Using my own equipment’s
37 b) Doing only what I am trained to do
c) Riding in car pools
d) Helping others with their jobs
In case of accident, the victim should immediately be_________.
a) Asked to take rest
38 b) Enquires about the accident
c) Attended to
d) Left to himself without treatment
Accidents are_________.
a) preventable
39 b) Costly
c) Part of life
d) Both a and b
If I have an accident or injury I should________.
a) Fix what I broke
40 b) Tell my supervisor
c) Keep working and not worry about it
d) Report it within a week
The responsibility of fire prevention belongs to_________.
a) Manager
41 b) Supervisor
c) Everyone
d) Fire department
I can prevent electrical fire by_________.
a) Non turning on lights
42 b) Never plugging anything into an outlet
c) Both a and b above
d) Not overloading electrical circuit
Fire extinguishers have a short use period of about
a) 8-15 sec
43 b) 1-2 min
c) 2-3 hours
d)4-5 days
Which of the following colours allows you to identify a foam fire extinguisher?
a) Blue
44 b) Red
c) Yellow
d) Cream
 The acronym for putting out a fire using a fire extinguisher is PASS. What does
PASS stand for:

45 a) Pull, Aim, Squeeze, Spread

b) Pull, Accuracy, Squeeze, Spread
c) Pin, Aim, Squeeze, Sweep
d) Pull, Aim, Squeeze, Sweep
Which of the following types of materials is responsible for fuelling a Class A
fire?
a) Oils that you typically cook with
46
b) Flammable liquids
c) Electrical Equipment
d) Wood, plastic, paper, and other kinds of solid materials
In the event of a fire, everyone is responsible for:
a) Informing the supervisor of what is happening.
47 b) Pulling the fire alarm if they see a fire.
c) Making sure everyone gets to the fire assembly point safely
d) None of the above
What type of permit is needed in order to carry out work that could potentially
result in a fire breaking out on the work site?
a) A fire permit
48
b) A hot permit
c) A work permit
d)No permit is needed
What class of fire was a Combustible Metal?
a) Class A fire
49 b) Class D fire
c) Class F fire
d) Class B fire
Who has the authority to pull the fire alarm after discovering a fire on the
worksite?
a) Only the manager can activate the fire alarm
50
b) Anyone who has seen a fire can activate the fire alarm.
c) Only the health and safety rep can activate the fire alarm
d) Only the owner can activate the fire alarm.