Titledraft.

fm Page 3 Wednesday, May 9, 2001 1:13 PM

5877 Personas Large Screen ATM

Installation Manual

P Y
C O
F T 1
R A 20 0
D a y
M
Publication ID: B006-6209-A000

Date: 0501
Titledraft.fm Page 4 Wednesday, May 9, 2001 1:13 PM

The product described in this book is a licensed product of NCR Corporation.

Trademark Information

It is the policy of NCR Corporation (NCR) to improve products as new technology, components,
software, and firmware become available. NCR, therefore, reserves the right to change specifications
without prior notice.

All features, functions, and operations described herein may not be marketed by NCR in all parts of
the world. In some instances, photographs are of equipment prototypes. Therefore, before using this
document, consult with your NCR representative or NCR office for information that is applicable and
current.

To maintain the quality of our publications, we need your comments on the accuracy, clarity,
organization, and value of this book.

Address correspondence to:

NCR Financial Solutions Group Ltd

Information Solutions
Kingsway West
Dundee, Scotland
DD2 3XX

© 2001
By NCR Corporation
Dayton, Ohio U.S.A.
All Rights Reserved
Book.bk Page iii Wednesday, May 9, 2001 11:59 AM

Federal Communications
Commission (FCC) Radio Frequency
Interference Statement
Note: This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be
required to correct the interference at his own expense.

This digital apparatus does not exceed the Class A limits for radio
Canadian Class A noise emissions from digital apparatus set out in the Radio
Device Declaration Interference Regulations of the Canadian Department of
Communications.
Le présent appareil numérique n’émet pas de bruits
radioélectriques dépassant les limites applicables aux appareils
numériques de la classe A prescrites dans le Réglement sur le
brouillage radioélectrique édicté par le ministère des
Communications du Canada.

P77 Large Screen ATM - Installation Manua - DRAFT COPY MAY 2001 iii
Book.bk Page iv Wednesday, May 9, 2001 11:59 AM

This equipment must be installed and used in strict accordance with

Information to User the manufacturer’s instructions. However, there is no guarantee
that interference to radio communications will not occur in a
particular commercial installation. If this equipment does cause
interference, which can be determined by turning the equipment off
and on, the user is encouraged to consult an NCR service
representative immediately.

Caution NCR Corporation is not responsible for any radio or television

interference caused by unauthorised modifications of this
equipment or the substitution or attachment of connecting cables
and equipment other than those specified by NCR. Such
unauthorized modifications, substitutions, or attachments may void
the user’s authority to operate the equipment. The correction of
interference caused by such unauthorized modifications,
substitutions, or attachments will be the responsibility of the user.

iv P77 Large Screen ATM - Installation Manua - DRAFT COPY MAY 2001
Book.bk Page v Wednesday, May 9, 2001 11:59 AM

Revision Record

Date Page Description of Change

May 01 All New Publication

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001 v
Book.bk Page vi Wednesday, May 9, 2001 11:59 AM

vi P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page vii Wednesday, May 9, 2001 11:59 AM

About This Document

Preface

Preface

This manual is intended for NCR personnel, or NCR customer

personnel who are required to install an NCR 5877 Large Screen
ATM (P77).
The purpose of this manual is to describe how to take the P77 from
its point of delivery and install it in the required location.
This manual is divided into five chapters:
● Chapter 1, Installation Procedures: This chapter lists the steps
and tools required to install an P77, and details how to move
the P77.
● Chapter 2, Unpacking The P77: This chapter describes how to
unpack the P77 and remove it from its pallet.
● Chapter 3, InstallingThe P77: This chapter describes the
procedures for installing the P77.
● Chapter 4, Configuring The P77: This chapter describes the
configuration procedure for the P77.
● Chapter 5, Fitting Decals to The P77: This chapter describes
how to apply decals to the front of the P77.
To install your P77 you must follow the procedures given in each
chapter, starting at Chapter 1 and working through to Chapter 4.
The procedures in Chapter 5 can be followed at any time, before or
after the installation of the P77.

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001 vii
Book.bk Page viii Wednesday, May 9, 2001 11:59 AM

About This Document

Preface

viii P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page ix Wednesday, May 9, 2001 11:59 AM

Table of Contents

Contents

About This Document

Preface ......................................................................................................vii

Chapter 1
Installation Procedures

Introduction............................................................................................1-1
Site Preparation.................................................................................1-1
Tools Required For Installation Of The P77 ......................................1-2
Moving the P77 ......................................................................................1-3
Packaging Dimensions.....................................................................1-4

Chapter 2
Unpacking The P77

Removing The External Packaging.....................................................2-1

Air/Sea Packaging ...........................................................................2-1
Road Packaging ................................................................................2-1
Inspecting For Damage.........................................................................2-2
Installation Report Form .................................................................2-2
Removing From The Pallet ..................................................................2-3
Air/Sea Pallet (Using a Fork-Lift)..................................................2-3
Road Pallet (Using Lifting Trolleys) ..............................................2-5
Conforming To AFA Regulations .....................................................2-10

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001 ix
Book.bk Page x Wednesday, May 9, 2001 11:59 AM

Table of Contents

Chapter 3
Installing The P77

Opening The Exterior of The P77 ....................................................... 3-1

Top Cabinet - Opening .................................................................... 3-1
Top Cabinet - Closing ...................................................................... 3-3
Security Enclosure - Opening......................................................... 3-4
Opening/Closing The Standard Security Enclosure ....................... 3-5
Lock Types ........................................................................................ 3-5
Keylocks............................................................................................. 3-7
Combination Locks .......................................................................... 3-7
Security Enclosures with Controlled Access Electronic Lock ...... 3-10
Opening Electronic Lock ............................................................... 3-11
Closing Electronic Lock................................................................. 3-12
Opening/Closing An Enclosure With Electronic Access Lock .... 3-13
Unlock The Factory Set Combination ......................................... 3-13
Lock The Security Enclosure Door .............................................. 3-14
Removing The Internal Packaging ................................................... 3-15
Top Cabinet - Internal Packaging ................................................ 3-15
Standard Security Enclosure - Internal Packaging.................... 3-17
Stabilising the P77 - Standard Security Enclosures........................ 3-22
Bolting The P77 To The Floor ............................................................ 3-23
Security Bolts Specifications ......................................................... 3-23
Bolting To The Floor ...................................................................... 3-24
Connecting Cables - Standard Security Enclosure......................... 3-26

Chapter 4
Configuring the P77

Introduction ........................................................................................... 4-1

Currency Cassette ................................................................................. 4-2
Miscellaneous Interface And RS-232 Interface ................................. 4-3
40-Column Printer ................................................................................ 4-8
Switch Settings................................................................................ 4-11
Receipt Form Length Setup .......................................................... 4-12
Communications ................................................................................. 4-14

x P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page xi Wednesday, May 9, 2001 11:59 AM

Table of Contents

Chapter 5
Fitting Decals To The P77

Introduction............................................................................................5-1
Applying Decals To The P77 ...............................................................5-2
Card Reader (Orientation) Entry/Exit Slot...................................5-2
Card Acceptance Window ..............................................................5-4
Receipt And Cash Exit .....................................................................5-4

Index
Index ...............................................................................................Index-1

User Feedback Form

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001 xi
Book.bk Page xii Wednesday, May 9, 2001 11:59 AM

Table of Contents

xii P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page xiii Wednesday, May 9, 2001 11:59 AM

Table of Contents
Installation Procedures

Chapter 1
Installation Procedures

Introduction 1-1
Site Preparation 1-1

Tools Required For Installation Of The P77 1-2

Moving the P77 1-3

Packaging Dimensions 1-4

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page xiv Wednesday, May 9, 2001 11:59 AM

Table of Contents
Installation Procedures

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page 1 Wednesday, May 9, 2001 11:59 AM

Installation Procedures
A

Introduction

Introduction 1

The installation of the terminal can be divided into several steps:

● Moving the P77
● Unpacking the P77
● Inspecting the P77 for damage
● Removing the shipping pallet
● Removing the internal packaging
● Bolting the P77 to the floor
● Connecting cables to the P77
● Configuring the P77 (if necessary)
● Applying decals to the P77.
These steps are described in detail in the chapters that follow.

Before installing the P77 make sure that the proposed installation
Site Preparation 1
site conforms with the specifications given in the NCR 5877 Large
Screen ATM Site Preparation (B006-6208-A000).
Note: If the P77 is being installed in an alcove or in an area with
restricted access from the rear, cable connections MUST be carried
out before the unit is moved into its final location.

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001 1-1
Book.bk Page 2 Wednesday, May 9, 2001 11:59 AM

Installation Procedures
Tools Required For Installation Of The P77

Tools Required For Installation Of

The P77 1

When installing your terminal it is recommended that you have the

following items available:
● Pincers/claw hammer to remove staples/nails from around the
air/sea pallet
● 19mm (3/4 in.) for UL safe, ring/open-ended combination
spanner and socket to remove pallet bolts, and to fit floor bolts
● Cross-head screwdriver
● 13mm (7/32 in.) spanner or socket - to remove the four screws
that secure the cross struts to the pallet
● 10mm (13/32in.) ring/open ended combination spanner - for
attaching earth stud
● 17 mm (11/16 in.) ring/open-ended combination spanner or
socket
● Wooden/metal safety blocks to support P77 during installation
● 4mm (7/64 in.) Allen key
● Hex nut driver set (including M3 and M4 sizes)
● Selection of screwdrivers for flat blade and cross head
applications
● Forklift or a lifting/moving device
● Packing to protect exterior of P77 while on trolleys
● Lifting Trolleys (these may need to be modified, refer to 5877
Large Screen ATM Installation Manual (B006-6209-A000)
● Scissors.

1-2 P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page 3 Wednesday, May 9, 2001 11:59 AM

Installation Procedures
Moving the P77

Moving the P77 1

To reduce the chance of damaging the P77, and/or the premises, the
P77 should be moved with its packaging intact.
Move the P77 to its approximate installation site using either a fork-
lift truck or a moving trolley.
There are two types of pallet and external packaging used on the
P77:
● Air/Sea Pallet with the P77 protected by a Cardboard Container
- Used when the P77 has been shipped by air/sea.
● Road Pallet with the P77 protected by a Plastic Covering - Used
when the P77 is delivered straight from the factory.

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001 1-3
Book.bk Page 4 Wednesday, May 9, 2001 11:59 AM

Installation Procedures
Moving the P77

Packaging
******** Dimensions of Crate Needed ************
Dimensions 1

Air and Sea Road

Air/Sea Package: 1

● Height = 1920mm (75.6 in.)

● Depth = 1140mm (47.6 in.)
● Width = 810mm (31.8 in.)

Road Package: 1

● Height = 1839mm (72.4 in.)

● Depth = 1215.5mm (47.9 in.)
● Width = 790mm (31.1 in.)
*************** CORRECT DIMENSIONS NEEDED ****************

1-4 P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page v Wednesday, May 9, 2001 11:59 AM

Table of Contents
Unpacking The P77

Chapter 2
Unpacking The P77

Removing The External Packaging 2-1

Air/Sea Packaging 2-1
Road Packaging 2-1

Inspecting For Damage 2-2

Installation Report Form 2-2

Removing From The Pallet 2-3

Air/Sea Pallet (Using a Fork-Lift) 2-3
Road Pallet (Using Lifting Trolleys) 2-5

Conforming To AFA Regulations 2-10

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page vi Wednesday, May 9, 2001 11:59 AM

Table of Contents
Unpacking The P77

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page 1 Wednesday, May 9, 2001 11:59 AM

Unpacking The P77 B

Removing The External Packaging

Removing The External Packaging 2

Before removing the external packaging, examine the packaging for

signs of damage which may have occurred during transit.
TILTWATCH® indicators attached to the outside of the packaging
show if the P77 has been badly handled. Make a note of any
external signs of damage for inclusion in a damage report. Refer
“Installation Report Form” for details on reporting damage.
With the P77 approximately in its final installation position, remove
the external packaging as follows:

Remove the air/packaging as follows:

Air/Sea Packaging 2

1 Lever out the staples from around the base of the

cardboard carton.
2 Remove strapping and lift the carton from the pallet.
3 Remove Remote Status Indicator box (if supplied).
4 Remove the plastic cover.

Remove the road packaging as follows:

Road Packaging 2

1 Remove the plastic cover.

2 Remove the Romote Status indicator box (if supplied).
**** INFORMATION NEEDED FOR THIS SECTION*****

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001 2-1
Book.bk Page 2 Wednesday, May 9, 2001 11:59 AM

Unpacking The P77

Inspecting For Damage

Inspecting For Damage 2

After unpacking the P77, inspect it for any visible signs of damage.
If the P77 is damaged, report the damage on the Installation Report
Form which is delivered with the P77.
● Customers who are required to arrange their insurance locally
should have the claim processed locally. A separate report of
damage should be made to Inventory Return Control, Dayton
● Customers who have insurance arranged by NCR Insurance
Department, Dayton, must report the damage on Form F-2100
(Notice of Damage) to NCR Insurance Department and send a
copy to Inventory Return Control.
The addresses for NCR Insurance and Inventory Return Control are:
● Risk Management and Insurance, NCR Corporation, Dayton,
Ohio 45479, U.S.A.
● Inventory Return Control, International Field Engineering
Support, NCR Corporation, Dayton, Ohio 45479, U.S.A.

The Installation Report Form which is delivered with the P77 must
Installation Report be completed and returned. Make sure that you detail any problems
Form 2 in the following areas:
● Functionality of the P77 or any of its devices
● Internal or external defects arising as a result of handling or
transit damage
● Missing or damaged accessories. All the P77 accessories are
fitted at the appropriate feature inside the P77.

2-2 P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page 3 Wednesday, May 9, 2001 11:59 AM

Unpacking The P77

Removing From The Pallet

Removing From The Pallet 2

To remove the P77 from the air/sea pallet you will require a fork-
lift, or a similar lifting/moving device.
To remove the P77 from a road pallet you will require a fork-lift or a
pair of lifting trolleys.

To remove the P77 from the pallet using a fork-lift, proceed as

Air/Sea Pallet follows:
(Using a Fork-Lift) 2

1 From the under-side of the pallet, use a 19mm (3/4 in.) spanner
and socket to remove the four bolts extending through to the
transportation feet.

2 Remove any wooden blocks attached to the pallet.

3 Insert the forks of the fork-lift through the slots in the
transportation feet. Lift the terminal off the pallet and remove
the pallet from beneath the P77.

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001 2-3
Book.bk Page 4 Wednesday, May 9, 2001 11:59 AM

Unpacking The P77

Removing From The Pallet

Warning Safety blocks must always be used when the P77 is supported by
a lifting device and work is to be done under the P77.

4 Lower the terminal on to safety blocks, use a 17mm (2/3 in.)

spanner or socket to remove the six bolts which secure the
transportation feet to the base of the terminal.
Note: Keep the bolts, as they may be needed for stabilising the
P77.
5 Raise the terminal and remove the transportation feet.
6 Move the P77 to the installation site.

Caution: When moving the terminal do not apply force to the top cabinet.
Any force used to move the terminal should be applied to the lower
cabinet.

7 Carefully remove the terminal from the fork-lift.

2-4 P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page 5 Wednesday, May 9, 2001 11:59 AM

Unpacking The P77

Removing From The Pallet

To remove the terminal from a road pallet using lifting trolleys

Road Pallet (Using proceed as follows:
Lifting Trolleys) 2

1 Using a screwdriver, remove the eight (8) wood screws securing

the two (2) panels (one each side) to the pallet and remove the
two panels from the pallet.

Screws
(8 off)

Removable
Panel (2 off)

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001 2-5
Book.bk Page 6 Wednesday, May 9, 2001 11:59 AM

Unpacking The P77

Removing From The Pallet

2 Using a 19mm (3/4 in.) spanner and socket, remove the four
bolts from the under-side of the pallet.

2-6 P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page 7 Wednesday, May 9, 2001 11:59 AM

Unpacking The P77

Removing From The Pallet

3 Position the lifting trolleys on either side of the pallet and insert
the toes of the trolleys into the slots of the transportation feet.
Strap the trolleys to the P77. Insert packing where necessary to
protect the P77’s paint work.
Note: The lifting trolleys may need to be modified to fit in between
the transportation feet, as shown below.

4 Pump up both trolleys to lift the P77 clear of the pallet.

Warning Safety blocks must always be used when the P77 is supported by
a lifting device and work is to be done under the P77.

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001 2-7
Book.bk Page 8 Wednesday, May 9, 2001 11:59 AM

Unpacking The P77

Removing From The Pallet

5 Using a 13mm (17/32in.) spanner or socket, remove the four

screws that secure the rear cross strut to the pallet. Remove the
strut and slide the pallet out from under the P77.

Remove Screws

2-8 P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page 9 Wednesday, May 9, 2001 11:59 AM

Unpacking The P77

Removing From The Pallet

6 Lower the terminal on to safety blocks, use a 17mm (2/3 in.)

spanner or socket to remove the six bolts which secure the
transportation feet to the base of the terminal.
Note: Keep the bolts, as they may be needed for stabilising the
P77 (Standard Security Only).
7 Raise the terminal and remove the transportation feet.

Remove 6 Bolts

8 Move the P77 to the installation site.

Caution: When moving the terminal do not apply force to the top cabinet.
Any force used to move the terminal should be applied to the lower
cabinet.

9 Carefully remove the terminal from the trolleys.

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001 2-9
Book.bk Page 10 Wednesday, May 9, 2001 11:59 AM

Unpacking The P77

Conforming To AFA Regulations

Conforming To AFA Regulations 2

To ensure conformance with the Americans with Disabilities Act

(ADA) and/or the Canadian Standards Authority (CSA) Access For
All (AFA) regulations, the transportation feet must be removed to
allow the base of the P77 to sit directly on the floor surface.

2-10 P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page xi Wednesday, May 9, 2001 11:59 AM

Table of Contents
Installing The P77

Chapter 3
Installing The P77

Opening The Exterior of The P77 3-1

Top Cabinet - Opening 3-1
Top Cabinet - Closing 3-3
Security Enclosure - Opening 3-4

Opening/Closing The Standard Security Enclosure 3-5

Lock Types 3-5
Primary Lock Types: 3-5
Secondary Lock Types: 3-5
Position of Primary and Secondary Locks 3-6
Keylocks 3-7
Unlock A Keylock 3-7
Lock A Keylock 3-7
Combination Locks 3-7
Factory Set Combination- Unlocking 3-8
Customer Set Combination - Unlocking 3-9
Silent Alarm - Operating 3-9
Combination Lock - Locking 3-9
Combination - Changing 3-9

Security Enclosures with Controlled Access Electronic Lock 3-10

Opening Electronic Lock 3-11
Closing Electronic Lock 3-12

Opening/Closing An Enclosure With Electronic Access Lock 3-13

Unlock The Factory Set Combination 3-13
Lock The Security Enclosure Door 3-14

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page xii Wednesday, May 9, 2001 11:59 AM

Table of Contents
Installing The P77

Removing The Internal Packaging 3-15

Top Cabinet - Internal Packaging 3-15
Standard Security Enclosure - Internal Packaging 3-17

Stabilising the P77 - Standard Security Enclosures 3-22

Bolting The P77 To The Floor 3-23

Security Bolts Specifications 3-23
Bolting To The Floor 3-24

Connecting Cables - Standard Security Enclosure 3-26

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page 1 Wednesday, May 9, 2001 11:59 AM

Installing The P77 C

Opening The Exterior of The P77

Opening The Exterior of The P77 3

The top cabinet and security enclosure can be opened

indepentently of each other.

To open the to cabinet of the P77, proceed as follows:

Top Cabinet -
1 If necessary, locate and retreive the facia key from the
Opening 3

document bag secured to the outside of the unit.

2 Insert the key, in the facia lock.
3 Turn (in either direction) and hold the key to open the lock.
4 Using one hand, pull the facia forwards.
5 Release the key.

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001 3-1
Book.bk Page 2 Wednesday, May 9, 2001 11:59 AM

Installing The P77

Opening The Exterior of The P77

6 Using both hands, carefully pull the facia out of the top cabinet
until the slides are fully extended.

3-2 P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page 3 Wednesday, May 9, 2001 11:59 AM

Installing The P77

Opening The Exterior of The P77

Close the top cabinet as follows:

Top Cabinet -
Closing 3

Caution Do not grip the facia when closing the top cabinet.

1 With your hands flat, either side of the keypad, push the facia
into the top cabinet until the lock locks.

2 Remove the key.

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001 3-3
Book.bk Page 4 Wednesday, May 9, 2001 11:59 AM

Installing The P77

Opening The Exterior of The P77

To open the security enclosure, proceed as follows:

Security Enclosure -
1 Inset the key into the lower cabinet door, and turn it clockwise.
Opening 3

2 Open the cabinet door.

3 Opening the security enclosure depends on the type security
enclosure and lock configuration. Refer to the relevant
procedure (detailed in “Opening/Closing The Standard
Security Enclosure”) for the lock configuration applicable to the
P77.

3-4 P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page 5 Wednesday, May 9, 2001 11:59 AM

Installing The P77

Opening/Closing The Standard Security Enclosure

Opening/Closing The Standard

Security Enclosure 3

The standard security enclosure will have a locking handle plus

either one lock (primary ), or two locks (primary and secondary).
The make of lock (Standard, or Sargent and Greenleaf) fitted
depends on the configuration of the P77. The procedures for
opening and closing the various types of lock are the same for both
makes.

The possible lock types for primary and secondary locks are as
Lock Types 3
follows:

Primary Lock Types: 3

● Keylock
● Combination lock
● Combination lock with silent alarm
● Combination lock with keylock
● Electronic access lock (see Note:)
● Controlled access lock (see Note:).
Note: The Controlled Access and Electronic Access Locks are
manufactured by Mas-Hamilton. The procedure for opening and
closing these locks differs from the others.

Secondary Lock Types: 3

● Keylock
● Combination lock
● Combination lock with silent alarm
● Combination lock with electronic override.

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001 3-5
Book.bk Page 6 Wednesday, May 9, 2001 11:59 AM

Installing The P77

Opening/Closing The Standard Security Enclosure

Position of Primary and Secondary Locks 3

The following illustration shows the relative positions of primary

and secondary locks.
Primary Lock

0
90 10

80

20
70

30
60 40
50

Locking Handle

Secondary Lock

0
90 10

80

20
70

30
60 40
50

Front Access

Opening Sequence of the Primary and Secondary Locks

If the P77 has a primary and a secondary lock fitted, the opening
sequence is as follows:
1 Unlock the secondary lock.
2 Unlock the primary lock.
3 Use the handle to retract the bolt and open the safe door.
Closing Sequence of the Primary and Secondary Locks
The primary and secondary locks must be locked in the following
sequence:
1 Close the door and use the handle to operate the bolt.
2 Lock the primary lock.
3 Lock the secondary lock.

3-6 P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page 7 Wednesday, May 9, 2001 11:59 AM

Installing The P77

Opening/Closing The Standard Security Enclosure

The pair of keylock keys supplied with the P77 have been pre-cut to
Keylocks 3
a random factory-set combination. If one key should get lost, then
you should get a new pair of keys and then change the keylock
setting.

Unlock A Keylock 3

To unlock a keylock, insert the key into the lock and turn it
clockwise as far as it will turn.-

Lock A Keylock 3

To lock a keylock, turn the key counter-clockwise as far as it will

turn and then remove the key.

Three variants of combination lock may be fitted to the P77:

Combination Locks 3

● basic combination lock

● combination lock with a keylock fitted in it
● combination lock with a silent alarm option.
All the variants of the combination lock are three-number
combination locks.
The locks are precision locks, therefore, extreme care must be taken
to align combination numbers with the index.
Turn the dial slowly and steadily. If, after turning the dial the
correct number of revolutions, any number is turned beyond the
index, the entire series of combination numbers must be re-dialled.
Do not turn the dial back to regain a proper alignment of the
number and index, because each time a selected number is aligned
with the index a revolution is counted.
The procedures for unlocking and changing the combination on a
combination lock are the same regardless of whether the lock is a
primary or secondary lock.

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001 3-7
Book.bk Page 8 Wednesday, May 9, 2001 11:59 AM

Installing The P77

Opening/Closing The Standard Security Enclosure

Opening Index
Changing Index

0
90 10

80

20
Dial

70

30
60 40
50

Factory Set Combination- Unlocking 3

If the combination lock is set at the original factory setting of 50,

unlock it as follows, dialling on the opening index:
1 If a keylock is fitted to the combination lock, insert the key into
the lock and turn it clockwise.
2 Turn the dial a minimum of four turns counter-clockwise and
stop on 50.
3 Turn the dial slowly clockwise until the bolt retracts. The lock is
now open. Use the handle on the door to retract the door bolt
and open the door.

3-8 P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page 9 Wednesday, May 9, 2001 11:59 AM

Installing The P77

Opening/Closing The Standard Security Enclosure

Customer Set Combination - Unlocking 3

If the combination has been set at a three-number combination, for

example 36-82-44, unlock it as follows:
1 If a keylock is fitted to the combination lock, insert the key into
the lock and turn it clockwise.
2 Turn the dial counter-clockwise, passing the first number (36)
three times, stop on the first number (36) the fourth time.
3 Turn the dial clockwise, passing the second number (82) twice,
and stop on the second number (82) the third time.
4 Turn the dial counter-clockwise, passing the third number (44)
once, and stop on the third number (44) the second time.
5 Turn the dial clockwise until the bolt retracts. The lock is now
open. Use the handle on the door to retract the door bolt and
open the door.

Silent Alarm - Operating 3

The silent alarm is triggered, if fitted, by adding 10 to the first

number of the combination. For example if the first number was 34,
dial 44 to trigger the silent alarm. Dial the next two numbers of the
combination as normal, the combination lock will open as normal
but the alarm will have been triggered.

Combination Lock - Locking 3

To lock the combination lock, turn the dial at least four complete
turns counter-clockwise. If a keylock is fitted to the combination
lock, turn the dial until 0 is in line with the opening index and then
turn the key
counter-clockwise and remove it from the lock.

Combination - Changing 3

Detailed instructions on how to change the combination of a lock

are inside the security enclosure.

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001 3-9
Book.bk Page 10 Wednesday, May 9, 2001 11:59 AM

Installing The P77

Security Enclosures with Controlled Access Electronic Lock

Security Enclosures with Controlled

Access Electronic Lock 3

For P77s with security enclosures fitted with a Mas-Hamilton

controlled access electronic lock, refer to the following Mas-
Hamilton Group publications for details of how to set up and
manage the lock operations:
● CENCON System 2000 Access Control System
● Getting Started Guide
● Supervisor Guide
● Special Supervisor Guide
● FLM Dispatcher Guide
● Route Dispatcher Guide
● CENCON 2000 System Guide.
These publications can be purchased from the following Order
Point:
Mas-Hamilton Group
805-D Newtown Circle
LEXINGTON
Kentucky
40511-1240
Tel: (1) 606 253-4744
Fax: (1) 606 253-4748
For the attention of Customer Service Manager

3-10 P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page 11 Wednesday, May 9, 2001 11:59 AM

Installing The P77

Security Enclosures with Controlled Access Electronic Lock

To open a security enclosure with a Mas-Hamilton controlled access

Opening Electronic electronic lock in Bank Mode (1 User) proceed as follows:
Lock 3

1 Spin the knob on the lock counter-clockwise.

Note: Rotating the knob counter-clockwise generates enough
power within the lock to allow it to operate for 90 seconds after
the rotation stops. The LCD powers down after 40 seconds.
Upon power up, the LCD will provide instructions for the user
to follow while opening the enclosure.

2 Keep spinning the knob until EC appears on the LCD and beeps
are heard.
3 Enter personal combination number (or the factory default
number - 50-25-50) using the keypad.
4 IPI (Input Personal Identifier) will appear on the LCD.

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001 3-11
Book.bk Page 12 Wednesday, May 9, 2001 11:59 AM

Installing The P77

Security Enclosures with Controlled Access Electronic Lock

5 Hold the personal identification key against the key reader.

Note: The lock processor will generate a combination number
and compare the user entered combination number with the
generated combination number.
6 If the combination number and the generated combination
number match, the LCD will display Opr and beeps will be
heard.
7 If the knob is now turned clockwise the lock will open and the
locking bolt will retract. The security enclosure door can then be
opened.
8 If the combination numbers do not match, a lightning bolt
symbol (to indicate a security violation) will appear on the LCD.
If this occurs, follow the in-house security procedures for this
condition.

To close the security enclosure, proceed as follows:

Closing Electronic
1 Close the security enclosure door.
Lock 3

2 Turn the electronic lock knob counter-clockwise to close.

3 Spin the knob counter-clockwise (to power up the electronic
lock) until beeps are heard.
4 IPI will appear on the LCD.
5 Hold the personal identification key against the key reader.
6 EOP (End of Operation) will appear on the LCD.

3-12 P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page 13 Wednesday, May 9, 2001 11:59 AM

Installing The P77

Opening/Closing An Enclosure With Electronic Access Lock

Opening/Closing An Enclosure With

Electronic Access Lock 3

The procedures given in this section relate only to the use of the
Εlectronic access lock when it is set at the factory setting.
Full details of how to operate the lock, including how to set and
change combinations, can be found in the MAS-Hamilton, Model 50
and D50 User Operations instructions shipped with the P77.

The lock is shipped pre-set so that any 2-digit number (except 00),
Unlock The Factory followed by the factory code of 502550 will open the lock.
Set Combination 3

To unlock the lock proceed as follows:

1 Power the lock by turning the dial in any direction until the red
and green lights flash and a beep is heard. This indicates that
the lock is powered-up and ready to be used.

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001 3-13
Book.bk Page 14 Wednesday, May 9, 2001 11:59 AM

Installing The P77

Opening/Closing An Enclosure With Electronic Access Lock

2 Position the lock dial so that the lip on the dial covers the red
label on the lock. Use the keypad to enter any 2-digit number
(except 00) and then the code 502550. When the combination
has been entered correctly the green light will give one slow
flash to indicate that the lock is ready to open.
3 Turn the dial slowly clockwise until the bolt retracts. The lock is
now open. Use the handle on the door to retract the door bolt
and open the door.

Close the security enclosure door and use the door handle to engage
Lock The Security the door bolt. Turn the lock dial counterclockwise until the lock bolt
Enclosure Door 3 engages.

3-14 P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page 15 Wednesday, May 9, 2001 11:59 AM

Installing The P77

Removing The Internal Packaging

Removing The Internal Packaging 3

This section details how to remove the internal packaging from the
P77.
Note: The amounts and types of packing may be subject to change
without notice. Ignore those steps which apply to modules not
installed in the P77.

The internal packaging in the top cabinet is shown in the following

Top Cabinet - diagram:
Internal Packaging 3

Tape

Tape

Foam

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001 3-15
Book.bk Page 16 Wednesday, May 9, 2001 11:59 AM

Installing The P77

Removing The Internal Packaging

To remove the internal packaging from the top cabinet proceed as

follows:
1 Unlock and rack out the top cabinet.
2 Remove the tape and foam from the following modules and
areas:
● Receipt printer
● Receipt printer mounting - locking knob
● Journal printer
● Underside of the module tray.
3 Close and lock the top cabinet.

3-16 P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page 17 Wednesday, May 9, 2001 11:59 AM

Installing The P77

Removing The Internal Packaging

The internal packaging in the security enclosure is shown in the

Standard Security following diagram.
Enclosure - Internal
Packaging 3

Foam

Tape

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001 3-17
Book.bk Page 18 Wednesday, May 9, 2001 11:59 AM

Installing The P77

Removing The Internal Packaging

Remove the tape and foam from the standard security enclosure as
follows:
1 Unlock and open the lower cabinet door of the P77.
2 Remove the Document Envelope taped to the inside of P77
lower cabinet door, this contains the followings items.
● Change keys for safe locks
● Spare keys for door
● Safe keys.
3 Remove tape from dials (may vary depending on
configuration).
4 Open the security enclosure.
5 Remove tape/foam from the following areas inside the security
enclosure:
a Dispenser Module Handle - Remove foam block and tape.

3-18 P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page 19 Wednesday, May 9, 2001 11:59 AM

Installing The P77

Removing The Internal Packaging

b Dispenser Transport Nose - Remove foam sheet and tape .

c Enclosure Wall - Remove foam blockl.

Note: There is only a foam block where the dispenser is

configured as 3-high or 4-high.

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001 3-19
Book.bk Page 20 Wednesday, May 9, 2001 11:59 AM

Installing The P77

Removing The Internal Packaging

d Cassettes - Remove tape from cassette latches.

3-20 P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page 21 Wednesday, May 9, 2001 11:59 AM

Installing The P77

Removing The Internal Packaging

e Configuration Kit (optional) - Remove from inside each

cassette supplied.

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001 3-21
Book.bk Page 22 Wednesday, May 9, 2001 11:59 AM

Installing The P77

Stabilising the P77 - Standard Security Enclosures

Stabilising the P77 - Standard

Security Enclosures 3

It is recommended that the P77 be installed on a smooth, even and

level floor surface with an antistatic floor covering. Refer NCR 5877
Large Screen ATM Site Preparation (B006-6208-A000).
If the P77 is to be stabilised, use the bolts retained from the
transportation feet removal.
Locate the holes (on the inside base of the P77) where bolts for the
transportation feet were removed from (see below). Insert the
bolt(s) downwards just far enough to stabilise the P77 and prevent it
from rocking.
Note: Do not over tighten bolt(s) as this may cause damage to the
P77 base or the floor surface.

3-22 P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page 23 Wednesday, May 9, 2001 11:59 AM

Installing The P77

Bolting The P77 To The Floor

Bolting The P77 To The Floor 3

Warning The P77 must be bolted to the floor.

The floor must be prepared as detailed in the NCR 5877 Large Screen
ATM Site Preparation (B006-6208-A000).
Bolt holes must be drilled prior to final siting of the P77. The above
site preparation manual provides dimensions for bolt hole locations.

Two (2) security bolts are required to bolt the P77, with the Standard
Security Bolts Security Enclosure, to the floor.
Specifications 3

Note: The securing bolts, anchors and appropriate washers must be

supplied by the owning organisation.
The minimum specification for bolts to secure the P77 to a plinth or
a stone/concrete floor is:
● M12 Rawlbolt - 12mm (0.47 in.) diameter x 38mm
(1.5 in.) minimum long
● Anchor point for M12 Rawlbolt, length suitable to clamp
25.4mm (1 in.) minimum of bolt..

Tighten only to
compress
Spring Washer Anchor Washer

Safe

Ground

Rawlbolt

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001 3-23
Book.bk Page 24 Wednesday, May 9, 2001 11:59 AM

Installing The P77

Bolting The P77 To The Floor

To bolt the P77 to the floor proceed as follows:

Bolting To The Floor 3

1 Open the lower cabinet door.

1 Open the security enclosure.
2 Lift the currency dispenser latch, and pull the currency
dispenser out of the P77 until its slides are fully extended.

3-24 P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page 25 Wednesday, May 9, 2001 11:59 AM

Installing The P77

Bolting The P77 To The Floor

3 Locate the holes in base of safe, position washers and insert

bolts through the holes. Tighten the bolts fully.
4 Push the dispenser back into the P77.
5 Close and lock the security enclosure. Proceed to “Connecting
Cables To The P77”.

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001 3-25
Book.bk Page 26 Wednesday, May 9, 2001 11:59 AM

Installing The P77

Connecting Cables - Standard Security Enclosure

Connecting Cables - Standard

Security Enclosure 3

The cables used to make connections to the P77 must conform to the
cable specifications and details provided in the NCR 5877 Large
Screen ATM Site Preparation (B006-6208-A000).
*****************************************************************************
BECAUSE THERE ARE NOW TWO CABLE ACCESS HOLES FOR
THE P77, THIS SECTION NEEDS TO BE SORTED OUT WHEN
THE CABLE ROUTING HAS BEEN FINALIZED.
*****************************************************************************

Caution Cables must be grounded where indicated to make sure that the P77
meets EMC requirements.

Warning Make sure that the power supply cable is not connected to the
mains power supply while you are connecting it to the P77.
1 Open the top cabinet of the P77.
2 Set the mains power switch to OFF (press in at the “0” side).
3 Close the top cabinet.
4 Open the lower cabinet door.
5 Open the security enclosure.

3-26 P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page 27 Wednesday, May 9, 2001 11:59 AM

Installing The P77

Connecting Cables - Standard Security Enclosure

6 Disconnect the power supply cable from the power supply unit
and loosen the two M6 screws which secure the metal ducting.

Plate

M6 Screws

7 If necessary, rack the currency dispenser out of the terminal

until its slides are fully extended.

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001 3-27
Book.bk Page 28 Wednesday, May 9, 2001 11:59 AM

Installing The P77

Connecting Cables - Standard Security Enclosure

8 Slide the metal ducting towards forwards and lift it clear into
the space between the currency dispenser and the power
supply.

9 Pass the ends of all cables to be installed through the hole in the
rear of the P77. Pull the cables through the hole.

3-28 P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page 29 Wednesday, May 9, 2001 11:59 AM

Installing The P77

Connecting Cables - Standard Security Enclosure

10 There are three (3) earth studs at both ends of the metal ducting
with “P” clamps attached to them, as shown below. Remove the
clamps from the metal ducting.
Note: It may be easier to remove the clamps by turning the metal
ducting upside down.

M4 Nut
Earth Stud Clamp

11 Select and fit the appropriate “P” clamps to each cable as

required. Refer to the following table to select the correct clamp.

System/Device Cable P Clamp Size

Comms/RS232 6.0mm (0.24in.)

Remote Status Indicator/Alarm Interface 4.5mm (0.18in.)

Remote Relay/Night Depository 3.38mm (0.13in.)

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001 3-29
Book.bk Page 30 Wednesday, May 9, 2001 11:59 AM

Installing The P77

Connecting Cables - Standard Security Enclosure

12 Attach each clamped cable to two earth studs, one at each end
of the metal ducting. Use the M4 nuts supplied.

Metal Plate

Earth Stud

3.38mm (0.13in.)
Clamp
or
4.5mm (0.18in.)
Clamp
M4 Nut securing or
cable clamp 6.0mm (0.24in.)
Clamp

Note: Attached all the clamps even if some are not used as they
may be required at a later date.
13 Connect the power supply cable, to the filter.

Power Supply Filter

Cable

14 Refit the metal ducting, ensuring all the cables are routed
underneath it, and secure by tightening the two M6 screws.

3-30 P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page 31 Wednesday, May 9, 2001 11:59 AM

Installing The P77

Connecting Cables - Standard Security Enclosure

15 The RS-232 High Order Communications cable must also be

grounded to the bottom tapped hole on the safe wall. This must
be done using appropriate “P” clamps and M4 x 10 screws, as
shown below.

Cable Clamp

M4 x 10 Screw

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001 3-31
Book.bk Page 32 Wednesday, May 9, 2001 11:59 AM

Installing The P77

Connecting Cables - Standard Security Enclosure

16 The Night Depository cable must also be grounded to the top

tapped hole on the safe wall. This must be done using
appropriate “P” clamps and M4 x 10 screws, as shown below.

Cable Clamp

M4 x 10 Screw

17 If necessary, push the dispenser back into the P77.

3-32 P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page 33 Wednesday, May 9, 2001 11:59 AM

Installing The P77

Connecting Cables - Standard Security Enclosure

18 Connect the cable(s) to the power supply unit.

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001 3-33
Book.bk Page 34 Wednesday, May 9, 2001 11:59 AM

Installing The P77

Connecting Cables - Standard Security Enclosure

3-34 P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page xxxv Wednesday, May 9, 2001 11:59 AM

Table of Contents
Configuring the P77

Chapter 4
Configuring the P77

Introduction 4-1

Currency Cassette 4-2

Miscellaneous Interface And RS-232 Interface 4-3

40-Column Printer 4-8

Thermal Receipt Printer 4-8
Thermal Journal Printer 4-9
Dot-Matrix Journal Printer 4-10
Switch Settings 4-11
Receipt Form Length Setup 4-12

Communications 4-14

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page xxxvi Wednesday, May 9, 2001 11:59 AM

Table of Contents
Configuring the P77

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page 1 Wednesday, May 9, 2001 11:59 AM

Configuring the P77 D

Introduction

Introduction 4

After you have completed the hardware installation and unpacking

of the P77 there are certain procedures which, depending on the
configuration of the P77, must be carried out.
Refer to the NCR 5877 Large Screen ATM, Operator Manual (B006-
6210-A000) for details of how to load test media.
The features which may require configuration are:
● Currency cassette - set cassette for local currency
● Miscellaneous Interface - configure:
● Nightsafe
● Indicators
● Alarms
● Media Entry Indicators
● RS-232 Interface(s) - set external device; door access or camera
type
● Printers
● 40-Column printers - test factory settings
● Communications protocols.
The configuration of these features is described in the following
sections.
After completing the installation and configuration of the terminal,
refer to the NCR 5877 Large Screen ATM, Operator Manual (B006-
6210-A000) for details of how to initialise the P77. On completion of
installation and testing, complete and return the Installation
Report form which is delivered with the P77.

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001 4-1
Book.bk Page 2 Wednesday, May 9, 2001 11:59 AM

Configuring the P77

Currency Cassette

Currency Cassette 4

The currency cassettes must be configured as detailed in the

following publication: H-8015-STD1-01/02-08 Currency Cassette
Owner’s Manual (BD10-1297-0000).

4-2 P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page 3 Wednesday, May 9, 2001 11:59 AM

Configuring the P77

Miscellaneous Interface And RS-232 Interface

Miscellaneous Interface And RS-232

Interface 4

If the P77 has a Miscellaneous Interface and/or an RS-232 Interface

fitted, these interfaces must be configured to identify what type of
device is attached to them. If there are interfaces to be configured
the terminal configuration program will be run automatically when
the P77 is switched on. If there are interfaces to be configured, a
screen similar to the following will be displayed
.

TERMINAL CONFIGURATION

CONFIGURATION INCOMPLETE

PRESS ANY KEY TO

CONFIGURE TERMINAL

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001 4-3
Book.bk Page 4 Wednesday, May 9, 2001 11:59 AM

Configuring the P77

Miscellaneous Interface And RS-232 Interface

Proceed as follows:
1 Press any key. A menu similar to the following will be
displayed:

CONFIGURE SERVICES

SELECT AN OPTION (0=HELP)

1. CONFIGURE MISCELLANEOUS I/F

2. CONFIGURE RS232

< EXIT

2 Select which interface type you wish to configure. If you select

CONFIGURE RS232 go to Step 7.
3 When the CONFIGURE MISCELLANEOUS I/F option is
selected a menu similar to the following is displayed:

CONFIGURE MISCELLANEOUS I/F

SELECT SERVICE (0=HELP)

1. ALARMS
2. INDICATORS
3. PROXIMITY DETECTOR
4. MEDIA ENTRY INDICATORS
5. NIGHT SAFE

< CONFIG SERVICES

● To return to the CONFIGURE SERVICES menu select the

CONFIG SERVICES option

4-4 P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page 5 Wednesday, May 9, 2001 11:59 AM

Configuring the P77

Miscellaneous Interface And RS-232 Interface

● YES or NO will be displayed alongside ALARMS, MEDIA

ENTRY INDICATORS and PROXIMITY DETECTOR
depending on whether the device is configured or
deconfigured
● NO, COMBINED, INDEPENDENT or DEFAULT will be
displayed alongside INDICATORS depending on the
current configuration
● NO, BASIC or ENHANCED will be displayed alongside
NIGHT SAFE depending on the current configuration
● NOT CONFIGURED will be displayed alongside a device if it
has never been configured
4 Select the device for which you want to change the
configuration. In the case of the ALARMS, PROXIMITY
DETECTOR and MEDIA ENTRY INDICATORS selecting the
device will cause its configuration state to toggle. For example,
if the menu shows the alarms to be configured, by displaying
YES alongside ALARMS, selecting ALARMS will cause it to be
deconfigured and a NO will be displayed alongside ALARMS.
5 If you select INDICATORS a menu similar to the following will
be displayed:

CONFIGURE INDICATORS

INDICATOR: XXXXXXXX

SELECT INDICATORS TYPES

1. COMBINED
2. INDEPENDENT
3. NONE
4. DEFAULT

< CONFIG MISC I/F

● COMBINED - the facia light and the in-service indicator

operate together and both are controlled by the status of the
in-service indicator
* FACIA LIGHT / ADVERT LIGHT STUFF NEEDS SORTING *

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001 4-5
Book.bk Page 6 Wednesday, May 9, 2001 11:59 AM

Configuring the P77

Miscellaneous Interface And RS-232 Interface

● INDEPENDENT - the facia light and the in-service indicator

operate independently
● NONE - deconfigures the indicators.
● DEFAULT - the facia light and in-service indicator remain
as set by the miscellaneous interface driver/manager.
Note: The P77 does not have an in-service indicator. If your P77 is a
vestibule unit or a freestanding (lobby) unit with a facia advert light
or a remote status indicator or a remote relay, you must select
DEFAULT or INDEPENDENT. Selecting NONE deconfigures the
indicators.
6 After selecting the mode of operation, select CONFIG MISC
I/F option to return to the CONFIGURE MISCELLANEOUS I/F
MENU. From this menu select CONFIG SERVICES to return to
the CONFIGURE SERVICES MENU.
7 If you select the CONFIGURE RS232 option on the CONFIGURE
SERVICES menu, a menu similar to the following is displayed:

CONFIGURE NCR RS232

SELECT I/F (0=HELP)

1. RS232#1:
2. RS232#2:

< CONFIG SERVICES

Note: Only those interfaces which are installed in the P77 will
be offered as configurable. To return to the CONFIGURE
SERVICES menu select the CONFIG SERVICES option.

4-6 P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page 7 Wednesday, May 9, 2001 11:59 AM

Configuring the P77

Miscellaneous Interface And RS-232 Interface

8 Select the RS232 interface that you want to configure. A menu

similar to the following is displayed:

CONFIGURE RS232

RS232#?: XXXXXXXXXX

SELECT DRIVE

1. CAMERA
2. DOOR ACCESS

< CONFIG NCR RS232

For DOOR ACCESS, select the required configuration and then

the CONFIG NCR RS232 option to return to the CONFIGURE
NCR RS232 menu.
9 If a camera is connected to the interface, select the CAMERA
option. A menu similar to the following is displayed:

CONFIGURE CAMERA

CAMERA: XXXXXXXXXXX

SELECT CAMERA TYPE

1. 3M
2. D/A FILM
3. D/A VIDEO
4. DIGITAL CAMERA

< CONFIG RS232

Select the type of camera connected to the interface and then

select the CONFIG RS232 option to return to the CONFIGURE
RS232 menu. Select CONFIG RS232 to return to the
CONFIGURE RS232 menu.

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001 4-7
Book.bk Page 8 Wednesday, May 9, 2001 11:59 AM

Configuring the P77

40-Column Printer

40-Column Printer 4

The P77 contains two variants of the 40-column printer - Receipt

and Journal.
Note: If customisation is necessary, switch settings and detailed
change instructions can be found in Chapter 13 of the Service Aids
Mini-Manual (BFM0-0547-A000). Adjusting the DIP switch settings
must be performed by a field service engineer.

Thermal Receipt Printer 4

4-8 P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page 9 Wednesday, May 9, 2001 11:59 AM

Configuring the P77

40-Column Printer

Thermal Journal Printer 4

Item 1 is a 6-dip switch pack on the Thermal printers. The 4

switches and their functions are:

Switch Function
1 Black mark sensing
2 Dot-matrix receipt variant
3 Not used
4 Not used
5 Diagnostics
6 Form length setup

Factory delivered configuration:

● Switch 1: Black mark sensing - on (receipt only)
● Switch 2: Dot-matrix receipt variant emulation- on
● International character set.

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001 4-9
Book.bk Page 10 Wednesday, May 9, 2001 11:59 AM

Configuring the P77

40-Column Printer

Dot-Matrix Journal Printer 4

Item 2 is an 8-dip switch pack on the Dot-Matrix printer. The 4

switches and their functions are:

Switch Function
1 to 6 Not used
7 International character set (OFF) and
Arabic character set (ON)
8 Not used

Factory delivered configuration - All switches off (International

character set selected).

4-10 P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page 11 Wednesday, May 9, 2001 11:59 AM

Configuring the P77

40-Column Printer

The following table lists the switch settings necessary to achieve the
Switch Settings 4
functions shown on thermal printers only.
Use these switches to change from the default settings.
Key:
● 1 = On
● 0 = Off
● n = refer to the next section “Receipt Form Length Setup”.

Switch Settings
Function
6 5 4 3 2 1

0 1 0 1 0 1 Black mark calibration

0 1 1 0 0 1 International character set (default)

0 1 1 0 1 0 Arabic character set

0 1 1 0 1 1 Thermal head set up (default = A)

Receipt Printer

0 1 1 1 0 0 Thermal head set up (default = A)

Journal Printer

1 n n n n n Form length set up (default = 24).

Refer to the table in the next section, “Receipt
Form Length Setup” for the values of n.

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001 4-11
Book.bk Page 12 Wednesday, May 9, 2001 11:59 AM

Configuring the P77

40-Column Printer

This function sets the length (in number of printed lines) of the
Receipt Form receipt, it is used for receipt paper with no black mark.
Length Setup 4

Set the length of the receipt as follows:

1 Remove the printed circuit board cover by lifting up from the
bottom of the cover and pulling the top away from the printer.
2 Set the dip switches to the settings that equal the number of
printed lines for the form length wanted, as shown in the
following table:
Switch Settings Form Length
6 5 4 3 2 1 (Lines)

1 0 0 0 0 0 24
1 0 0 0 0 1 25
1 0 0 0 1 0 26
1 0 0 0 1 1 27
1 0 0 1 0 0 28
1 0 0 1 0 1 29
1 0 0 1 1 0 30
1 0 0 1 1 1 31
1 0 1 0 0 0 32
1 0 1 0 0 1 33
1 0 1 0 1 0 34
1 0 1 0 1 1 35
1 0 1 1 0 0 36
1 0 1 1 0 1 37
1 0 1 1 1 0 38
1 0 1 1 1 1 39
1 1 0 0 0 0 40
1 1 0 0 0 1 41
1 1 0 0 1 0 42
1 1 0 0 1 1 43
1 1 0 1 0 0 44
1 1 0 1 0 1 45
1 1 0 1 1 0 46
1 1 0 1 1 1 47
1 1 1 0 0 0 48
1 1 1 0 0 1 49

4-12 P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page 13 Wednesday, May 9, 2001 11:59 AM

Configuring the P77

40-Column Printer

Note: Dip switch six (6) must be set to ON for a minimum form
length of 24 printed lines. Switch settings give up to a maximum
number of 49 printed lines. Settings greater than 49 default to 49.
3 Press the reset button to store the form length.
4 Set the switches to the customer requirements and press the
reset switch on the supervisor/operator panel.
5 Place the pcb cover back onto the printer; attach the bottom of
the cover to the bottom of the pcb and then attach the top of the
cover to the top of the pcb.
Note: Make sure the corners of the pcb are captured by the slots on
the upper right and left corners of the cover.

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001 4-13
Book.bk Page 14 Wednesday, May 9, 2001 11:59 AM

Configuring the P77

Communications

Communications 4

If you intend to use communications, then you must configure the

software and hardware.
Note: Before you can configure communications in the P77, you
must build and load the applications software onto the P77. The
procedures for building and loading software are in the NCR
publication Building A Load Disk (BD10-1797-0000). If your P77 uses
Personas PLATFORM For Windows NT, refer to the NCR
publication Using The Communications Feature (B006-0012-0000).
To configure communications you will require the protocol
identification code for the communications protocol to be used.
Protocol identification codes are in the NCR publication Quick
Reference Guide To Communications Manuals (BD10-2215-0000).
You will also require the communications common and connection
parameters and these must be supplied by the owning organisation.
To configure the communication protocols proceed as follows:
1 Unlock and open the top cabinet of the P77.
2 Press the ON/OFF switch to the ON position (press at the 1
side).
3 After the P77 has completed its power up procedures, a screen
similar to the following is displayed.

COMMUNICATIONS CONFIGURATION

1. NOT CONFIGURED
2. NOT CONFIGURED
3. NOT INSTALLED
4. NOT INSTALLED
5. EXIT

CONFIGURE TERMINAL

4-14 P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page 15 Wednesday, May 9, 2001 11:59 AM

Configuring the P77

Communications

4 Select the first, or only, communications protocol that is not

configured by pressing the 1 key on the operator panel.
5 The screen will change to the following.

COMMUNICATIONS CONFIGURATION

ENTER PROTOCOL ID

6 Enter the 2-digit protocol identification code. The digits will

appear on the screen as you enter them. If you make a mistake
while entering the code, press the cancel key and then re-enter
the code.
7 Press the enter key to accept the protocol identification code. If
any of the following error messages are displayed you will be
prompted to re-enter the protocol identification code:
● INVALID PROTOCOL ID - You have entered a protocol
identification code which does not exist
● NO TEMPLATE FILE - There is no template file on disk for
the protocol you entered
● NO DOWNLOAD FILE - There is no download file on disk
for the protocol you entered
● NO EXECUTABLE FILE - There is no executable file on disk
for the protocol you have entered.

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001 4-15
Book.bk Page 16 Wednesday, May 9, 2001 11:59 AM

Configuring the P77

Communications

8 If you are required to enter parameters for the protocol you

have selected, a screen similar to the following will be
displayed. The Parameters To Be Entered Must Be Supplied
By The Owning Organization. If a screen similar to the
following is not displayed, proceed to Step 11.

COMMUNICATIONS CONFIGURATION

A < PROTOCOL ID TEXT > B

< CURRENT CONNECTION >

C D

< ERROR MESSAGES >

E < PARAMETER TXT > (*) F

● The current connection can be either COMMON

PARAMETERS, PRIMARY CONNECTION, or CONNECTION
<3-digit connection number>.
● The parameter names and current settings are displayed
one at a time at the bottom of the screen. To accept the
default values specified for a parameter, press the enter
key. If there is no default value specified, if NO DATA is
displayed, you must enter a value.
● When you have finished entering data for a parameter,
press the enter key.

4-16 P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page 17 Wednesday, May 9, 2001 11:59 AM

Configuring the P77

Communications

9 When all the required parameters have been entered, or if no

parameters were required, a screen similar to the example
screen shown below will appear:

COMMUNICATIONS CONFIGURATION

1. IBM 2265 ASYNC

2. NOT CONFIGURED

3. NOT INSTALLED

4. NOT INSTALLED

5. EXIT

SELECT BOARD TO CONFIGURE

10 If there are other boards to be configured, repeat Steps 4 to 9.

11 Select the EXIT option by pressing the 5 key on the operator
keyboard. The screen will change to the following.

COMMUNICATIONS CONFIGURATION

1. YES

2. NO

CONFIGURATION OK?

12 Select NO if you want to go back and change the configuration,

otherwise select YES.
13 Close the exterior of the P77.

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001 4-17
Book.bk Page 18 Wednesday, May 9, 2001 11:59 AM

Configuring the P77

Communications

4-18 P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page xix Wednesday, May 9, 2001 11:59 AM

Table of Contents
Fitting Decals To The P77

Chapter 5
Fitting Decals To The P77

Introduction 5-1

Applying Decals To The P77 5-2

Card Reader (Orientation) Entry/Exit Slot 5-2
Card Acceptance Window 5-4
Receipt And Cash Exit 5-4

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page xx Wednesday, May 9, 2001 11:59 AM

Table of Contents
Fitting Decals To The P77

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page 1 Wednesday, May 9, 2001 11:59 AM

Fitting Decals To The P77 E

Introduction

Introduction 5

This chapter provides details on how to apply decals to the front of

the P77. Specifications for the decals to be applied can be found in
the 5877 Large Screen ATM Site Preparation (B006-6208-A000).

Clear Window

Receipt Exit Point

Card Reader

Card Orientation
Window

Cash Exit Point

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001 5-1
Book.bk Page 2 Wednesday, May 9, 2001 11:59 AM

Fitting Decals To The P77

Applying Decals To The P77

Applying Decals To The P77 5

To apply decals to the front of the P77, proceed as follows:

To apply a decal behind the clear window on the facia, proceed as

Card Reader follows:
(Orientation)
1 Insert the two window extraction tools (supplied with the P77)
Entry/Exit Slot 5

into the holes at the bottom of the plastic insert.

2 Pull the extraction tools forward and down to release the insert.
Pull the plastic insert towards you.

5-2 P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page 3 Wednesday, May 9, 2001 11:59 AM

Fitting Decals To The P77

Applying Decals To The P77

3 Securely place the decal in the recess provided. Replace the

plastic insert and ensure it clicks back into place.

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001 5-3
Book.bk Page 4 Wednesday, May 9, 2001 11:59 AM

Fitting Decals To The P77

Applying Decals To The P77

To apply a decal behind the card acceptance window on the facia,

Card Acceptance proceed as follows:
Window 5

1 Insert the two window extraction tools (supplied with the P77)
into the holes at the bottom of the plastic insert.

2 Pull the extraction tools forward and down to release the insert.
Pull the plastic insert towards you.
3 Securely place the decal in the recess provided. Replace the
plastic insert and ensure it clicks back into place.

Identify the exit slots and simply locate the appropriate decal and
Receipt And Cash place firmly onto the surface. Ensure the area is dry and clean prior
Exit 5 to adhesion.
Note: Refer to the NCR 5877 Large Screen ATM Site Preparation
Manual ( B006-6208-A000) for decal specifications and guidelines.

5-4 P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page 1 Wednesday, May 9, 2001 11:59 AM

Index

Index 0

40-Column Printer
Numerics Configuring 4-8
Receipt Form Length Setup 4-12
Switch Settings 4-11

About this Documen tvii

A ADA Conformance
Removal of Transportation Fe e 2-10
t
Air/Sea Pallet
Removing 2-3

Bolting To The Floor 3-23

B
Card Reader Entry/Exit Slot
C Fitting Decals 5-2
Changing
Combination 3-9
Closing
Controlled Access Electronic Lock 3-12
Electronic Access Lock 3-13
Standard Security Enclosure 3-5
The Top Cabinet 3-3
Closing Sequence
Primary and Secondary Locks 3-6
Combination
Changing 3-9
Combination lock 3-5
Customer setting 3-9
Factory setting 3-8
Locking 3-9
Unlocking
Customer setting 3-9
Factory Setting 3-8
With electronic override 3-5
With keylock 3-5
With silent alarm 3-5
Communications
Configuring 4-14

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001 Index-1
Book.bk Page 2 Wednesday, May 9, 2001 11:59 AM

Index

Configuring the P77

40-Column Printer 4-8
Communications 4-14
Currency Cassette 4-2
Introduction 4-1
Miscellaneous Interface 4-3
RS-232 Interface 4-3
Connecting Cables
Standard Security 3-26
Controlled Access Electronic Lock
Closing 3-12
Opening 3-11
Controlled access lock 3-5
CSA Conformance
Removal of Transportation Fe e 2-10
t
Currency Cassette
Configuring 4-2
Customer set combination
Unlocking 3-9

Electronic Access Lock 3-5

E Locking security enclosure 3-14
Unlocking factory set combination 3-13
Electronic access lock 3-13
Exterior
Opening 3-1

Factory set combination

F Unlocking 3-8, 3-13
FCC Statement iii
Canadian Class A Device Declaration iii
Information to User iv
Fitting Decals
Card Acceptance Window 5-4
Card Reader Entry/Exit Slot 5-2
Introduction 5-1
Receipt And Cash Exit 5-4

Getting Started
G Closing The Top Cabinet 3-3

Index-2 P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page 3 Wednesday, May 9, 2001 11:59 AM

Index

Inspecting For Damage

I Installation Report Form 2-2
Installation Procedures
Introduction 1-1
Moving the P77 1-3
Packaging Dimensions 1-4
Site Preparation 1-1
Tools Required 1-2
Installation Report Form 2-2
Installing the P77
Bolting To The Floor 3-23
Connecting Cables 3-26
Opening The Exterior 3-1
Opening/Closing
Controlled Access Electronic Lock 3-10
Electronic Access Lock 3-13
Standard Security Enclosure 3-5
Removing Internal Packaging 3-15
Stabilising 3-22
Internal Packaging
Removing 3-15

Keylock 3-5
K Locking 3-7
Unlocking 3-7

Locking
L Combination Lock 3-9
Keylock 3-7
Security enclosure 3-14

Mas-Hamilton 3-5
M Miscellaneous Interface
Configuring 4-3
Moving the P77 1-3

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001 Index-3
Book.bk Page 4 Wednesday, May 9, 2001 11:59 AM

Index

Opening
O Controlled Access Electronic Lock 3-11
Electronic Access Lock 3-13
Security Enclosure 3-4
Standard Security Enclosure 3-5
The Exterior 3-1
Top Cabinet 3-1
Opening Sequence
Primary and Secondary Locks 3-6
Operating
Silent Alarm 3-9

Packaging Dimensions 1-4

P Preface vii
Primary and Secondary Locks
Closing Sequence 3-6
Opening Sequence 3-6
Primary lock types
Combination lock 3-5
With keylock 3-5
With silent alarm 3-5
Controlled access lock 3-5
Electronic access lock 3-5
Keylock 3-5

Receipt Form Length Setup 4-12

R Removal of Transportation Feet
ADA Conformance 2-10
CSA Conformance 2-10
Removing
Internal Packaging 3-15
Removing Air/Sea Pallet
Using a Fork-Lift 2-3
Removing External Packaging 2-1
Removing Internal Packaging
Standard Security Enclosure 3-17
Top Cabinet 3-15
Removing Road Pallet
Using Lifting Trolleys 2-5
Revision Record v
Road Pallet
Removing 2-5
RS-232 Interface
Configuring 4-3

Index-4 P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page 5 Wednesday, May 9, 2001 11:59 AM

Index

Sargent and Greenleaf 3-5

S Secondary lock types 3-5
Combination lock 3-5
With electronic override 3-5
With silent alarm 3-5
Keylock 3-5
Security Bolt Specifications 3-23
Security Enclosure
Locking 3-14
Opening 3-4
Silent Alram
Operating 3-9
Site Preparation 1-1
Stabilising
P77 3-22
Standard Security Enclosure
Removing Internal Packaging
3-17
Standard security enclosure
Change The Combination 3-9
Combination locks 3-7
Connecting Cables 3-26
Customer set combination 3-9
Factory set combination 3-8
keylocks 3-7
Locking the Combination lock 3-9
Operationg the Silent alarm 3-9
Switch Settings
40-Column Printer 4-11

Tools Required 1-2

T Top Cabinet
Opening 3-1
Removing Internal Packaging 3-15
Transportation Feet
Removal 2-10

P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001 Index-5
Book.bk Page 6 Wednesday, May 9, 2001 11:59 AM

Index

Unlocking
U Customer set combination 3-9
Electronic access lock 3-13
Factory set combination lock 3-8
Keylock 3-7
Unpacking the P77
Inspecting For Damage 2-2
Removing External Packaging 2-1
Removing From The Pallet 2-3

Index-6 P77 Large Screen ATM - Installation Manual - DRAFT COPY MAY 2001
Book.bk Page 7 Wednesday, May 9, 2001 11:59 AM

User Feedback Form

Title: NCR 5877 Personas Large Screen ATM - Installation Manual

Number: B006-6209- A000 Date:
Cut

NCR welcomes your feedback on this publication. Your comments can be of great value in
helping us improve our information products.

You may send your comments, electronically, to the Information Solutions Department
at Dundee. See over for details.

Circle the numbers below that best represent your opinion of this publication.

Ease of use 5 4 3 2 1 0 5 = Excellent

Accuracy 5 4 3 2 1 0 4 = Good
Clarity 5 4 3 2 1 0 3 = Adequate
Completeness 5 4 3 2 1 0 2 = Fair
Organization 5 4 3 2 1 0 1 = Poor
Appearance 5 4 3 2 1 0 0 = Not Applicable
Examples 5 4 3 2 1 0
Illustrations 5 4 3 2 1 0
Job performance 5 4 3 2 1 0
Question resolution 5 4 3 2 1 0
Overall satisfaction 5 4 3 2 1 0

Indicate the ways you feel we could improve this publication.

❑ Improve the table of contents ❑ Add more/better quick reference aids

❑ Improve the overview/introduction ❑ Add more examples
❑ Improve the organization ❑ Add more illustrations
❑ Improve the index ❑ Add more step-by-step procedures
❑ Make it less technical ❑ Add more troubleshooting information
❑ Make it more concise/brief ❑ Add more detail
Book.bk Page 8 Wednesday, May 9, 2001 11:59 AM

Write any additional comments you may have below and on additional sheets, if necessary. Include
page numbers where applicable.

Use the following addresses to send your comments, electronically, to the Information Solutions
Department at Dundee:

Cut
WWW - http://www.ncr.com/product/infoprod/dundeeip/
e-mail - user.feedback@scotland.ncr.com

If we may contact you concerning your comments, please fill in the information below:

Name
Organisation:
Company:
Address:

Phone: Fax:

Thank you for your evaluation of this publication. Fold the form where indicated, tape (please do not
staple), affix stamp and drop in the mail.
F8763-0695
Fold

Affix
Postage
Stamp
Here

NCR Financial Solutions Ltd.

Information Solutions
Kingsway West
Dundee
Scotland
DD2 3XX
 P Y
C O
FT 01
R A 2 0
D a y
M

B006-6207-A000 0501