Scribd
Upload
381 views1 page

Engineering Drawing for Vessel

The document provides specifications and design details for a pressure vessel, including: 1) All welds must be neat in appearance and free of defects, and the vessel must be cleaned prior to testing. 2) The vessel has a maximum allowable working pressure of 200 psi at 300°F, weighs approximately 350 lbs dry and 500 lbs during testing, and has a capacity of 3 cubic feet for air. 3) Attached drawings provide dimensions, materials of construction, nozzle specifications, and other design details.

Uploaded by

Sourav Hait
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
381 views1 page

Engineering Drawing for Vessel

The document provides specifications and design details for a pressure vessel, including: 1) All welds must be neat in appearance and free of defects, and the vessel must be cleaned prior to testing. 2) The vessel has a maximum allowable working pressure of 200 psi at 300°F, weighs approximately 350 lbs dry and 500 lbs during testing, and has a capacity of 3 cubic feet for air. 3) Attached drawings provide dimensions, materials of construction, nozzle specifications, and other design details.

Uploaded by

Sourav Hait
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

NOTES: 1. All welds shall be neat in appearance, free of slag and other defects. 2.

Vessel to be cleaned of scale, oil, weld splatter and all foreign material prior to hydrostatic test. 3. Remove all sharp edges on nozzles (1/8" minimum radius) 4. All Nozzles to support nominal loads only. 5. Vessel weight ( approx. dry ) 350 lbs Vessel weight ( approx. test ) 500 lbs 6. Capacity 3 cu.ft. 7. Fluid: air

Certified by
XYZ Vessel Corp.

Item Qty

Description

Bill of Materials
Material

U
W
50.18
~
CRN

(Name of Manufacturer)

200

Max. allowable working pressure (MAWP)

psi (kPa) at

300

F (C)

Max. allowable external working pressure

psi (kPa) at

F (C)

-20

Minimum Design Metal Temperature (MDMT)

F (C) at

200 psi (kPa)

1 2 3 4 5 6 7 8 9 10

1 2 1 1 2 1 2 4 1 1

PIPE: 12" SCH. STD PIPE CAP: 12" SCH. STD PIPE: 4" SCH. 40 FLANGE: 4" 150# RSFO HALF CPLG: 2" 3000# NPT HALF CPLG: 1/2" 3000# NPT PLATE: 3/8" THICK PLATE: 7-1/2" x 2" x 3/8" MTG REINFORCEMENT CODE NAMEPLATE BRACKET CODE NAMEPLATE

SA-106B SA-234 WPB SA-106B SA-105 SA-105 SA-105 SA/CSA-G40.21 44W SA/CSA-G40.21 44W SA/CSA-G40.21 44W STAINLESS

N-0000
Manufacturer's serial number

6.00

36.00 18.00 N1 1 8.00 0.38


1/8 1/2 4 PLC

e Sa m
N3 120

O pl
(14.38) REF

12.75 OD N2

1.00 REF

nl

y
Year built

Design Data

1/4

TYP

5/8" HOLE TYP

12.00 (8.81) REF

N4 6 28.00 9 10

1/4

TYP

En

1.25

2.00

7.00 11.00

2.25

31.50 34.00 SIDE ELEVATION

Design Code: ASME Code Section VIII Division 1, 2004 Edition, A06 Design Pressure Internal: 200 psi @ 300F MAWP: 200 psi Design Pressure External: N/A MDMT: -20F @ 200 psi Hydro Test Pressure: 260 psi @ ambient for 1/2 Hour PWHT: None Radiography: None Corrosion Allowance: 0" Impact Test: Exempt per UG-20(f)

END VIEW
2 1 0
REV

PV

Updates Updates Release


DESCRIPTION

Aug 19/08 July 9/08 June 23/08

BEM BEM BEM


INITIALS

REVISION HISTORY

DATE

PVEng
nt nt

Pressure Vessel Engineering

120 Randall Drive, Suite B, Waterloo, Ontario, N2V 1C6 P: 519.880.9808 F: 519.880.9810 http://www.pveng.com info@pveng.com

TYP.

45

Nozzle Mark Size Qty

Flange

Service

Type

Welds Leg Leg 41 42


1 5 5 4" 16"

Leg 43
1 4"

Flange Weld SB (w)


3 8"

Nozzle

Nozzle Schedule

Outside Inside
UW-16.1 (c)
t

Inside

Nozzle

t Leg41

Full Pen.

Full t Pen. Leg41 t Outside Shell


Proj

Leg43

TITLE

PVE SAMPLE VESSEL


JOB ID DRAWING NO REV

N1 N2 N3 N4

4" 2" 2" 1/2"

1 1 1 1

VENT INLET OUTLET DRAIN

II I I I

16" 1 4"

0.216" -

SB

w w

SIZE

B
SCALE

Sample 2 1:8

Sample 2
SHEET

2 1 of 1

TYP. CIRC. SEAM

TYPE I

SLIP ON FLANGE

UW-16.1 (c) with inside projection

TYPE II

You might also like