Product Overview

Solutions for your single-use and multi-use

biopharma processes

Steriflow Valve is a Division of Richards Industrials

Product Overview 2

Steriflow Valve revolutionized the industry in the leader, offering a dependable pressure reducing
late 1980s with the introduction of the Mark 96 valve and back pressure regulator that adhered to
and 95 sanitary pressure regulators. The bio- the industry’s rigorous standards for drainability,
pharmaceutical industry created a demand for particulate minimization, surface finish and
advanced valve solutions capable of ensuring minimal offset. For precise control of clean steam
precise pressure control for validated steam pressure control, buffer pressure control and
and purified water applications. Jordan Valve’s purified water back pressure control, contact
Steriflow “regulator” emerged as the market Steriflow Valve.

Industry leader for sanitary regulators & control

valves for over thirty years

By 2007, Steriflow Valve had successfully introduced several control valves, regulators and clean steam specialty products.
The Steriflow Valve division was created to nurture continued innovation and to broaden its product scope.

Today, Steriflow Valve has a complete line of pressure regulators, control valves, gas pressure regulators, check valves,
sanitary safety relief valves, diaphragm valves, steam traps, ball valves and SIP accessories.

Steriflow has introduced a broad range of industry firsts for the bio-pharmaceutical industry:

» The industry’s first and only Lifetime Diaphragm Warranty

» The first true spring-less and crevice-free check valve for horizontal and vertical line WFI and bioprocess applications
» The world’s only down-flow check valve for bioprocess drain applications
» The world’s first precision aseptic metering valve
» The world’s largest pure steam trap and accessory product range including: products that shorten SIP heat-up time and
eliminate validation temperature alarm and reduce dripleg length
» The first clean gas regulator product line developed specifically for bio-pharmaceutical applications
» The first clean gas regulators designed specifically for reliable control of low flows and low pressures
» The first U.S. manufactured AMSE sanitary safety relief valves
» Sanitary steam traps with subcooling temperatures as low as 3°F (1,7°C) or less
Product Overview 3

Certifications, Credentials & Affiliations

Credentials
All Material Test Reports comply with the requirements of BSEN 10204, Type 3.1
Plastic and elastomer Certifications of Compliance included with every order:
» FDR CFR Title 21, Paragraph 177.1550 for plastic materials FDA
» FDR CFR Title 21, Paragraph 177.2600 for elastomer materials
» U.S. Pharmacopeia XXVIII Class VI, Chapter 88 Biological Reactivity Test in Vivo
» U.S. Pharmacopeia XXVIII, Chapter 87 Biological Reactivity Test in Vitro
» ADI/TSE Free Certificate
» Batch lot traceability for elastomer and plastic components
Steam trap fill fluids meet FDA/ICH Q3C/FDA Class 3 criteria designation

Documentation & Traceability

All Steriflow valves have serial numbers that are directly traceable to our Unicert, and to the heat numbers on the type 3.1
material test reports attached.

Affiliations
» ASME
» ASME BPE (membership & committee member)
» ISPE
» FCI (membership and Chairman)
» P.E. Registered Professional Engineer - State of Ohio, USA
» Valve Manufacturers Association (VMA)

Credentials
» ISO 9001:2015
» Pressure Equiment Directive (PED) 97/23/EC-PED Category 1
» CE (Conformité Européene)
» EX Certification available on designated products
» Canadian Registration Numbers (CRN) available on all products
Product Overview 4

The Jorlon™ Diaphragm: Unparalleled Reliability

What Is Jorlon™?

Jorlon™ is structurally modified pure PTFE. It is manufactured by a proprietary technique where PTFE layers are combined
and formed in a unique process to reduce the creep and cold flow associated with conventionally formed solid or laminated
PTFE or Teflon.

Jorlon™ is featured in all of Steriflow’s valve product lines:

» Mark 978 Control Valves » Mark 95 Back Pressure Regulating valves

» JSHM Manual Metering Valves » Mark 96A, 96AA, 95A, 95AA Air Loaded Regulators
» Mark 96 Pressure Regulating Valves » J Series Clean Gas Pressure & Back Pressure Regulators

Physical Properties of JorlonTM

Color Clear, translucent

Composition PTFE
Temperature Maximum 500° F/260°C
Creep Relaxation (ASTM F38) % 35
Specific Gravity (D792) 2.19
Compressibility (ASTM F36) % Range 20 - 25
Recovery (ASTM F36) Minimum % 50
Tensile Strength (ASTM D1708)
X Direction psi (N/mm2) 5000 (35)
2
Y Direction psi (N/mm ) 5100 (36)
Ultimate Elongation (ASTM D1708)
X Direction % 500
Y Direction % 520
Gas Permeability (ASTM D1434V) CC/M2/24 hrs 10,000
Lab tests comparing Jorlon™ to Flammability Will not burn
316L diaphragms have shown FDA CFR 21 177.1550,
continued life after exceeding the USP <88> Class VI
SST failure cycle count by more Industry Approvals/Certifications
USP <87>
than 100 times. ADI Free
Product Overview 5

Steriflow Valves in Bioreactor Processing

Unmatched Expertise & Product Range

Process engineers and researchers depend on Steriflow Valve for our comprehensive range of sanitary
products, designed to meet the diverse fluid control needs in biopharma processing. Our products offer
precise flow and pressure control, suitable for both upstream and downstream bioprocessing applications,
including usage with Water for Injection (WFI), clean process gases, steam, and for Clean-in-Place (CIP)/
Steam-in-Place (SIP) processes. Our experienced engineers collaborate with you to identify the most
effective fluid control solutions for your specific applications. Discover the versatility of our valves in
various stages of the bioreactor process.
Product Overview 6

Sanitary Control Valves Low, Medium, High Flows

Mark 978LF Series Mark 978M Series

Mark 978OR Series Mark 978JD Series FBCV-OR Series

Angle style or inline control valves, for continuous precision control of media, process, purified water and clean
utilities in the biopharmaceutical, pharmaceutical, food & beverage and consumer health & beauty industries:

» Bioreactor/fermenter process input control: growth » Purification input and output control: elution media,
media, buffer, WFI, sparge and blanket gas solvents, buffer, WFI
» Separation input and output control: WFI, process, » Formulation / fill control: WFI and other vessel inputs,
product & waste streams blanket gas, dosing pressure
» Small vessel formulation / fill control: WFI and other » Clean utilities: WFI, pure steam, CIP, clean compressed air
vessel inputs, blanket gas, dosing pressure and gas
» 3A certification for Food & Beverage line
Product Overview 7

MARK 978 SERIES, MEDIUM TO HIGH FLOW, CONTROL VALVE

Angle & Inline body: 1/2" - 3" (DN15 - DN80) - Jorlon Diaphragm
Sizes
1/2" - 2" (DN15 - DN50) - O-Ring Stem Seal
End Connections ASME, DIN & ISO Tri-Clamp, Extended Tube Weld
0.2 - 125 Cv (0,17 - 108 Kv), Linear, Equal Percenterage or Quick Opening - Jorlon Diaphragm
Cv (Kv) & Flow Characteristic
0.2 - 60 Cv (0,17 - 51,6 Kv), Linear, Equal Percentage or Quick Opening - O-Ring Stem Seal
150 psi (10,3 bar) at 100°F (38°C); 100 psi (6,9 bar) at 340°F (171°C) - Jorlon Diphargm
Max Pressure/Temperature 450 psi (31 bar) at 100°F (38°C); 450 psi (31 bar) at 450°F (232°C) - O-Ring Stem Seal
dependent upon body construction and o-ring
ASTM SA479 316L or 1.4435 SST; ASME BPE SF5, 20 Ra (0,5 µm) electropolish is standard, 8 Ra (0,2µm)
Wetted Material & Surface Finish
optional
All materials certified to FDA/USP Class VI - Jorlon
Stem Seal - Diaphragm
Various, all certified to FDA/USP Class VI - O-Ring
Soft Seat Option (Cv > 3.5 only) PTFE FDA/USP Class VI; PEEK FDA/USP Class VI

MARK 978LF SERIES, LOW FLOW, CONTROL VALVE

Sizes 1/2" & 3/4" (DN15 & 20)

End Connections ASME, DIN & ISO Tri-Clamp, Extended Tube Weld
Cv (Kv) & Flow Characteristic 0.005 - 0.1 Cv (0,0043 - 0,086 Kv), Linear or Equal Percentage
Max Pressure/Temperature 200 psi (13,8 bar) - Jorlon diaphragm dependent upon body construction; O-Ring dependent upon construction
ASTM SA479 316L or 1.4435 SST; ASME BPE SF5, 20 Ra (0,5 µm) electropolish is standard, 8 Ra (0,2µm)
Wetted Material & Surface Finish
optional
All materials certified to FDA/USP Class VI - Jorlon
Stem Seal - Diaphragm
Various, all certified to FDA/USP Class VI - O-Ring

MARK 978M SERIES, LOW TO HIGH FLOW, MANUAL CONTROL VALVE

Sizes Angle & Inline body: 1/2" - 2" (DN15 - DN50)

End Connections ASME, DIN & ISO Tri-Clamp, Extended Tube Weld
Cv (Kv) & Flow Characteristic 0.2 - 70,1 Cv (0,17 - 60,5* Kv), Linear, Equal Percentage or Quick Opening (*modified linear)
Max Pressure/Temperature 150 psi (10,3 bar) at 100° temperature dependent on o-ring construction
ASTM SA479 316L or 1.4435 SST; ASME BPE SF5, 20 Ra (0,5 µm) electropolish is standard, 8 Ra (0,2µm)
Wetted Material & Surface Finish
optional
Stem Seal - O-ring All materials certified to FDA/USP Class VI - Jorlon
Soft Seat Option (Cv > 3.5 only) PTFE FDA/USP Class VI; PEEK FDA/USP Class VI

FBCV-OR SERIES, 3A APPROVED, O-RING STYLE STEM SEAL, PROCESS CONTROL VALVE

Sizes 1/2" - 4" (DN15 - DN100)

End Connections Tri-Clamp
Cv (Kv) & Flow Characteristic 0.2 - 165 Cv (0,17 - 200 Kv), Linear or Equal Percentage
Max Pressure/Temperature 450 psi (31 bar) at 100°F (38°C) for 1/2" - 3"; 250 psi (17 bar) at 100°F (38°C) for 4"
Wetted Material & Surface Finish ASTM SA479 316L or 1.4435 SST; ASME BE SF5, 20 Ra (0,5 μm) electropolish is standard, 8 Ra (0,2 μm) optional
Stem Seal - O-ring Various - all certified to FDA/USP Class VI
Product Overview 8

Pressure Regulating Valves Low to High Flows

Mark 96C Series Mark 96AA Series

Mark 96 Series Mark 96A Series FB6C Series

Angle style or inline pressure reducing valves with bolted body for purified water, clean utilities and media in the
biopharmaceutical, pharmaceutical, food & beverage and consumer health & beauty industries. Also available with a
tri-clamp body for low flow and an automated or hybrid version.

» Media prep: AWFI (ambient WFI) or buffer dilution

» Bioreactor/fermenter process input control: AWFI
» Separation input and output control: AWFI
» Purification input and output control: AWFI, Buffer
» Clean utilities: USP PW, WFI, CIP, CCA, CCG
Product Overview 9

MARK 96C SERIES, TRI-CLAMP, LOW FLOW, MANUAL, JORLON™ DIAPHRAGM

Sizes 1/2", 3/4", 1" (DN15, DN20, DN25)

End Connections ASME, DIN & ISO Tri-Clamp, Extended Tube Weld
Cv (Kv) & Flow Characteristic 0.3 - 5.5 Cv (0,26 - 4,7 KV)
Max Pressure/Temperature Dependent upon construction
Setpoint Range 3 psi (0,2 bar) to 135 psi (9,3 bar); dependent on size of construction
Wetted Material & Surface Finish ASTM SA479 316L or 1.4435 SST; ASME BPE SF5, 20 Ra (0,5 μm) electropolish is standard, 8 Ra (0,2 μm) optional

Diaphragm Materials Jorlon™ FDA, USP Class VI; EPDM/Nylon - FDA only

Soft Seat Option Jorlon™, PEEK, Teflon (all materials FDA, USP Class VI)

MARK 96 SERIES, MANUAL, MEDIUM TO HIGH FLOW, JORLON™ DIAPHRAGM

Sizes 3/4" - 3" (DN20 - DN80)

End Connections ASME, DIN & ISO Tri-Clamp, Extended Tube Weld
Cv (Kv) & Flow Characteristic 1.5 - 23 Cv (1,3 - 19,8 Kv)
Max Pressure/Temperature Dependent upon construction
Setpoint Range 3 psi (0,2 bar) to 135 psi (9,3 bar); dependent on size and construction
ASTM SA479 316L or 1.4435 SST; ASME BPE SF5, 20 Ra (0,5μm) electropolish is standard,
Wetted Material & Surface Finish
8 Ra (0,2μm) optional

Diaphragm Materials Jorlon™ FDA, USP Class VI; EPDM/Nylon (FDA only)

Soft Seat Option Jorlon™, PEEK, Teflon (all FDA and USP Class VI)

MARK 96A & 96AA SERIES HYBRID OR AUTOMATED, JORLON™ DIAPHRAGM

Sizes 3/4" - 3" (DN20 - DN80)

End Connections ASME, Tri-clamp, ASME Butt Weld, ASME Tube Weld, DIN ISO Tri-Clamp, Tube Weld
Cv (Kv) & Flow Characteristic 1.5 - 23 Cv (1,3 - 19,8 kv) model dependent model dependent
Max Pressure/Temperature model dependent
Setpoint Range 3 psi (0,2 bar) to 135 psi (9,3 bar); dependent on size and construction
Wetted Material & Surface Finish ASTM SA479 316L or 1.4435 SST; ASME BE SF5, 20 Ra (0,5 μm) electropolish is standard, 8 Ra (0,2 μm) optional
Diaphragm Materials Jorlon™ FDA, USP Class VI
Soft Seat Option Jorlon™, PEEK, Teflon (all materials FDA, USP Class VI)

FB6C SERIES, 3A & FDA APPROVED, JORLON™ DIAPHRAGM

Sizes 3/4" - 3" (DN20 - DN80)

End Connections Tri-Clamp
Cv (Kv) & Flow Characteristic 0.6 - 29.4 Cv (0,5 - 25,4 Kv)
Max Pressure/Temperature 450 psi (31 bar) at 100°F (38°C) for 1/2" - 3"; 250 psi (17 bar) at 100°F (38°C) for 4"
Body Materials ASTM A351, CF3M 316L
Standard hard seat - integral 316L SST seat; optional soft seats: Jorlon™ (FDA & USP Class VI) for steam and
hot fluid service to 338°F (170°C), Cv 0.5 and larger only; PEEK (FDA & USP Class VI) for steam and hot fluid
Seat Materials
service to 350°F (177°C), Cv 0.5 and larger; PTFE (FDA & USP Class VI) to 252°F (122°C) continuous or 275°F
(135°C) intermittent (not to exceed 15 min. in a one hour period), Cv 0.5 and larger
Product Overview 10

Back Pressure Regulating Valves Low to High Flows

Mark 95A Series Mark 95FT Series

Mark 95 Series Mark 95LL Series FB5C Series

Angle style, flow-through or inline back pressure reducing valves for purified water, clean utilities and media in the
biopharmaceutical, pharmaceutical, food & beverage and consumer health & beauty industries.

» WFI distribution loop: return loop pressure maintenance » Separation input and output control: for perfusion TFE, for
upstream of spray ball TransMembrane Pressure (TMP) control
» Media / buffer prep, upstream process: input back » Purification input and output control: for chromatography
pressure control for mixing buffer, media; pressure column, TFE or depth filtration differential pressure
maintenance and relief to sterile containment control; pump head pressure maintenance or pressure
bypass; agitator or pump seal water pressure
maintenance
Product Overview 11

MARK 95 SERIES, LOW TO HIGH FLOW, JORLON™ DIAPHRAGM

Sizes 1/2" - 3" (DN15 - DN80)

End Connections ASME, Tri-clamp, ASME Tube Weld, DIN ISO Tri-Clamp, Tube Weld
Cv (Kv) & Flow Characteristic 0.5 - 28 Cv (0,4 - 24,1 KV)
Max Pressure/Temperature Dependent upon construction
Setpoint Range 3 psi (0,2 bar) to 90 psi (6,2 bar); dependent on size of construction
Wetted Material & Surface Finish ASTM SA479 316L or 1.4435 SST; ASME BPE SF5, 20 Ra (0,5 μm) electropolish is standard, 8 Ra (0,2 μm) optional

Diaphragm Materials Jorlon™ FDA, USP Class VI, 316L, EPDM/Nylon (FDA only)

Soft Seat Option Jorlon™, PEEK, Teflon (all materials FDA, USP Class VI)

MARK 95FT SERIES, MANUAL, FLOW-THROUGH BODY, LOW TO HIGH JORLON™ DIAPHRAGM

Sizes 1/2" - 3" (DN15 - DN80)

End Connections ASME, Tri-clamp, ASME Tube Weld, DIN ISO Tri-Clamp, Tube Weld
Cv (Kv) & Flow Characteristic 0.5 - 28 Cv (0,4- 24,1 Kv)
Max Pressure/Temperature Dependent upon construction
Setpoint Range 3 psi (0,2 bar) to 90 psi (6,2 bar); dependent on size and construction
ASTM SA479 316L or 1.4435 SST; ASME BPE SF5, 20 Ra (0,5μm) electropolish is standard,
Wetted Material & Surface Finish
8 Ra (0,2μm) optional

Diaphragm Materials Jorlon™ FDA, USP Class VI;, 316L, EPDM/Nylon (FDA only)

Soft Seat Option Jorlon™, PEEK, Teflon (all materials FDA and USP Class VI)

MARK 95A & 95AA SERIES HYBRID OR AUTOMATED, LOW TO HIGH FLOW, JORLON™ DIAPHRAGM

Sizes 1/2" - 3" (DN15 - DN80)

End Connections ASME, Tri-clamp, ASME Tube Weld, DIN ISO Tri-Clamp, Tube Weld
Cv & Flow Characteristic 0.5 - 28 Cv (0,4 - 24,2 kv)
Setpoint Range 3 psi (0,2 bar) to 90 psi (6,2 bar); dependent on size and construction
Wetted Material & Surface Finish ASTM SA479 316L or 1.4435 SST; ASME BE SF5, 20 Ra (0,5 μm) electropolish is standard, 8 Ra (0,2 μm) optional
Diaphragm Materials Jorlon™, USP Class VI
Soft Seat Option Jorlon™, PEEK, Teflon (all materials FDA and USP Class VI)

FB5C SERIES, 3A & FDA APPROVED, JORLON™ DIAPHRAGM

Sizes 3/4" - 3" (DN20 - DN80)

End Connections Tri-Clamp
Cv (Kv) & Flow Characteristic 0.5 - 28 Cv (0,4 - 24,1 Kv)
EPDM/Nylon to 275°F (135°C) 3A & FDA; Teflon Encapsulated Viton to 400°F (204°C) 3A & FDA; Jorlon™ to
Diaphragm Materials
400°F (204°C) 3A & FDA
Body Materials ASTM A351, CF3M 316L
Seat Materials Standard hard seat - integral 316L SST seat; soft seats available consult factory
Product Overview 12

Industrial Compressed Air & Gas Pressure Regulators &

Back Pressure Regulators

JR Series JRHF Series

JRLL Series JRDL Series JRH Series

Back air and gas pressure regulators are designed to handle very high pressures and very low flows. Pressure air
and gas regulators handle very high pressures and very low flows, low set pressures and very low flows and piston
operated regulators with high Cvs (Kvs).

» Biopharma research and sampling systems

» Clean room gas panels and gas distribution
» Gas chromatography
» Gas cabinets
Product Overview 13

JR SERIES, HIGH PRESSURE, LOW FLOW, JORLON™ DIAPHRAGM

JB SERIES, HIGH PRESSURE, LOW FLOW, JORLON™ DIAPHRAGM
Sizes 1/4", 3/8" & 1/2" (DN8, DN10 & DN15)
End Connections Threaded, Socket Weld, Flanged
Cv (Kv) 0.012, 0.03, 0.08, 0.20 (0,01, 0,026, 0,07, 0,17) JR Series; 0.05, 0.15, 0.25, 0.35 (0,04, 0,13, 0,22,0,30) JB Series
Spring Range up to 750 psi (52 bar)
Seat Type PTFE (JR Series only), PEEK, KEL-F

Diaphragm Materials Jorlon™ FDA & USP Class VI

JRDL SERIES, DIAPHRAGM OPERATED, HIGH PRESSURE, LOW FLOWS

JBDL SERIES, DIAPHRAGM OPERATED, HIGH PRESSURE, LOW FLOWS
Sizes 1/2", 3/4" & 1" (DN15, DN20 & DN25) JRDL Series; 1/2" (DN15) JBDL Series
End Connections Threaded, Socket Weld, Flanged
Cv (Kv) 1.7 (1,46) JRDL Series; 1.95 (1,69) JBDL Series
0-50 psi, 0-100 psi 0-200 psi, 0-400 psi (0,0-3,4 bar, 0-6,9 bar, 0-13,8 bar, 0-28 bar) JRDL Series;
Spring Range
up to 400 psi JBDL Series
Seat Type Buna-N, EPDM, VIton JRDL Series; KEL-F JBDL Series

JRH SERIES, MANUAL, VERY HIGH PRESSURE, LOW FLOW, JORLON™ DIAPHRAGM

Size 3/8" & 1/2" (DN10 & DN15)

End Connections Threaded, Socket Weld, Flanged
Cv (Kv) 0.08, (0.69)
Spring Range 2-10 psi and 75-450 psi (0,14-0,69 bar and 5,2-31 bar)
Seat Type KEL-F / Viton
Diaphragm Materials Jorlon™ FDA & USP Class VI

JRHF SERIES, DIAPHRAGM OPERATED, HIGH FLOWS, JORLON™ DIAPHRAGM

Sizes 1/2", 3/4", 1" (DN15, DN20, DN25)

End Connections Threaded, Socket Weld, Flanged
Cv (Kv) 1/2": 1.5 (1,3 KV); 3/4" - 1": 1.9 (1,6 KV)
Spring Range up to 150 psiI (10 bar)
Seat Type PTFE, PEEK
Dipahragm Materials Jorlon™ FDA & USP Class VI

JRHL SERIES, LOW SET PRESSURE, VERY LOW FLOWS, JORLON™ DIAPHRAGM

Sizes 1/2" & 3/4" (DN15 & DN20)

End Connections Threaded, Socket Weld, Flanged
Cv (Kv) 0.5 & 0.8 (0,43 & 0,7)
Spring Range up to 50 psi (3,45 bar)
Seat Type PTFE, PEEK, EPDM
Dipahragm Materials Jorlon™ FDA & USP Class VI
Product Overview 14

Compressed Air & Gas Pressure Regulators & Back

Pressure Regulators

JSRLF Series JSRHF Series

JSRLFLP Series JSR Series JSRH Series

Pharma clean compressed air and gas pressure reducing valves, NPT, Tri-Clamp or weld ends, very low to high flow,
manual or air augmented, with Jorlon™ lifetime diaphragm warranty.

» Bioreactor/fermenter: sparge gas, purge/blanket/motive » Formulation: purge/blanket/motive force gas regulation

force gas regulation for process vessels
» Separation: purge/blanket/motive force gas regulation » Lyophilization: purge/blanket/motive gorce gas
for process vessels regulation for process vessels
» Purification: purge/blanket/motive force gas regulation
for process vessels
Product Overview 15

JSR SERIES, MANUAL OR AIR AUGMENTED, LOW TO MEDIUM FLOW, JORLON™ DIAPHRAGM
JSB SERIES, MANUAL OR LOW TO MEDIUM, JORLON™ DIAPHRAGM
Sizes 1/2" & 3/4" (DN15 & DN20)
End Connections ASME BPE, DIN & ISO Tri-Clamp, Tube Weld & NPT (VCR optional)
Cv 0.8 - 0.5 Cv (0,7 - 0,43 Kv)
Max Inlet Pressure 150 psi (10,5 br)
Setpoint Range 5 psi to 125 psi (0,03 bar to 8,6 bar) JSR Series; 8 psi to 125 psi (0,06 bar to 8,6 bar) JSB Series

Diaphragm Materials Jorlon™ FDA & USP Class VI

JSRH SERIES, MANUAL, MEDIUM TO HIGH FLOW, JORLON™ DIAPHRAGM

Sizes 1/2", 3/4" & 1" (DN15, DN20 & DN25)

End Connections ASME BPE, DIN & ISO Tri-Clamp, Tube Weld & NPT
Cv (Kv) 1.5, 1.9 Cv (1,3, 1,64 Kv)
Max Pressure/Temperature 150 psi (10,5 bar) at 275°F (135°C)
Setpoint Range 5 psi (0,34 bar) to 150 psi (10,3 bar)

Diaphragm Materials Jorlon™ FDA & USP Class VI

JSRHF SERIES, MANUAL, MEDIUM TO HIGH FLOW, JORLON™ DIAPHRAGM

Sizes 3/4" - 2" (DN20 - DN50)

End Connections ASME BPE, DIN & ISO Tri-Clamp, Tube Weld & NPT
Max OperatingTemperature 250 psig @ 275°F (10,5 bar @ 135°C)
Max Operating Pressure 300 psi @ 100°F (20,7 bar @ 38°C)
Setpoint Range 5 - 250 psi (0,3 - 17,2 bar)
Diaphragm Materials Jorlon™ FDA & USP Class VI

JSRLF SERIES, MANUAL OR AIR AUGMENTED, JORLON™ DIAPHRAGM

JSBLF SERIES, MANUAL OR AIR LOADED, JORLON™ DIAPHRAGM
Sizes 1/4" - 3/4" (DN8 - DN20) JSRLF Series; 3/8", 1/2" & 3/4" (DN10, DN15 & DN20) JSBLF Series
End Connections ASME BPE, DIN & ISO Tri-Clamp, Tube Weld & NPT
Cv (Kv) 0.012 and 0.20 (0,01 and 0,17 Kv) JSRLF Series; 0.05, 0.15, 0.25, 0.35 (0,04, 0,13, 0,21, 0,30 Kv) JSBLF Series
Max Pressure/Temperature 450 psi @ 350°F (31,0 bar @ 177°C) with PEEK seats; 450 psi @ 150°F (30,1 bar @ 66°C) with PTFE seats
Setpoint Range 5 psi to 750 psi (0,3 bar to 52 bar) JSRLF Series; 5 psi to 450 psi (0,3 bar to 31 bar) JSBLF Series
Dipahragm Materials Jorlon™ FDA & USP Class VI

JSRLFLP SERIES, MANUAL OR AIR AUGMENTED, LOW FLOW & PRESSURE, JORLON™ DIAPHRAGM
JSBLFLP SERIES, LOW FLOW, LOW PRESSURE, JORLON™ DIAPHRAGM
Size 1/4", 3/8", 1/2", 3/4" (DN8, DN10, DN15, DN20) JSRLFLP Series; 3/8", 1/2", 3/4" (DN10, DN15, DN20) JSBLFLP Series
End Connections ASME BPE, DIN & ISO Tri-Clamp, Tube Weld & NPT

Cv (Kv) 0.012 and 0.20 (0,01 and 0,17 Kv) JSRLFLP Series; 0.05, 0.15, 0.25, 0.35 (0,04, 0,13, 0,21, 0,30 Kv) JSBLFLP Series

Tube & Tri-Clamp: 150 psi @ 350°F (10,3 bar @177°C) with PEEK seats; 150 psi @ 150°F (10,3 bar @ 66°F) with
Max Pressure/Temperature PTFE seats JSRLFLP Series; 250 psig (10,5 barg) for weld end or tri-clamp connections; 450 psig (31 barg) for
NPT connections JSBLFLP Series
Settpoint Range 1 psi to 50 psi (0,07 bar to 3,4 bar)
Dipahragm Materials Jorlon™ FDA & USP Class VI
Product Overview 16

Low Pressure Air & Gas Blanketing Regulators

Mark 908 Series Mark 908X Series

JSRULP Series JSRFULP Series

Pharma clean compressed air and gas blanketing (gas overlay) regulators (PRV, BPRV), very low flow to high flow,
very low pressure set points and manual control

» Separation: purge/blanket/motive force gas regulation and bag integrity testing for process vessels
» Purification: purge/blanket/motive force gas regulation and bag integrity testing for process vessels
» Formulation: purge/blanket/motive force gas regulation and bag integry testing for process vessels
» Single-use bag inflation
Product Overview 17

MARK 908/908X SERIES, MID TO HIGH FLOW, VERY LOW PRESSURE

Sizes 3/4" & 1" (DN20 & DN25) Mark 980 Series; 1/2" & 3/4" (DN15 & DN20) Mark 908X Series
End Connections ASME BPE, DIN & ISO Tri-Clamp, Flanged or NPT
Cv (Kv) 1.0 - 10 (0,86 - 8,65) Mark 908 Series; 0.15, 0.2, 0.4 (0,13, 0,17, 0,35) Mark 908X Series
Max Pressure/Temperature Maximum inlet: 200 psi @ 250°F (13,8 bar @ 121°C)
Setpoint Range 1/2" wc - 1.5 psi (1,25 mbarg - 103,4 mbarg)

Wetted Material & Surface Finish ASTM SA479 316L or 1.4435 SST; ASME BPE SF5, 20 Ra (0,5 μm)

Diaphragm Material Ultra-lightweight Teflon FDA/USP Class VI

Main Valve Seal Material EPDM and 316/Viton (all material is FDA/USP Class VI)

JSRLFULP SERIES LOW FLOW, LOW PRESSURE, CLEAN GAS REGULATOR

Sizes 1/2" & 3/4" (DN15 & DN20)

End Connections ASME BPE
Gauge Ports 1/4" FNPT is standard
Soft Seat Materials EPDM to 275°F (135°C), FDA & USP Class VI
Diaphragm Materials Jorlon™ FDA & USP Class VI
Spring Ranges 2" - 18" water (0,07 - 0,65 psi)

JSRHULP SERIES, HIGH PURITY, ULTRA LOW PRESSURE REGULATOR

Sizes 1/2", 3/4", 1" (DN15, DN20, DN25)

End Connections Tri-Clamp
Gauge Ports 1/4" FNPT is standard
Soft Seat Materials EPDM to 275°F (135°C), FDA & USP Class VI
Diaphragm Materials Jorlon™ FDA & USP Class VI
Spring Ranges 4" - 18" water (0,14 - 0,65 psi)

MARK 958/968 SERIES MEDIUM TO HIGH FLOW, BPRV/PRV

Sizes 3/4", 1", 1-1/2", 2" (DN20, DN25, DN40, DN50)

End Connections ASME BPE, DIN & ISO Tri-Clamp, Flanged - 150#, 300#, PN25/40
MK958: 368 SCFH to 22,953 SCFH (10 NM3/H to 650 NM3/H)
Flow Ranges
MK968: 201 SCFH to 19,258 SCFH (5,7 NM3/H to 545 NM3/H)
Max Pressure/Temperature Size dependent
Setpoint Range 2.0" w.c. to 5 psi (5 mbar to 344,7 mbar)
Diaphragm Materials FDA approved Viton
Wetted Material & Surface Finish Internal and external cast body components are 130 Ra (3,30 μm) minimum after electropolishing
Shutoff ANSI Class VI
Product Overview 18

Equilibar FDO Series Sanitary Back Pressure Regulators

Also available in Single Use technology

The Equilibar® FDO Series works differently, with synergistic design features that provide extreme precision, almost
instantaneous reaction, frictionless operation, and an exceptionally flexible flow rate range. It is compact, easily
automated and can be used for both back pressure control and flow control.

» Dome-loaded with multiple orifice flow paths with a flexible diaphragm that covers and seals the parallel orifices in the
FDO body
» The diaphragm lifts off the orifices to release pressure as the upstream process pressure exceeds the set-point pressure,
accounting for exceptionally wide flow range
» The flow rangeability and precision at extremely low pressures makes the FDO an excellent choice for transmembrane
pressure control in tangential flow filtrations (TFF)
Product Overview 19

FD SERIES, WIDE FLOW RANGE

Sizes 1/4", 1/2", 3/4", 1", 1-1/2", 2", 3"

End Connections ASME BPE, DIN & ISO Tri-Clamp, Tube Weld Ends
Cv 1E-6 to 36
Max Pressure 150 psig (10 barg)
Setpoint Range Depends on process

Wetted Material & Surface Finish ASTM SA479 316L or 1.4435 SST; ASME BPE SF5, less than 20 Ra (0,5 μm) electropolish

Jorlon™ USP Class VI, PTFE USP Class VI, EPDM USP Class VI, FKM Flouroelastomer, Buna-N,
Diaphragm Materials
Glass Reinforced PTFE

Pilot Setpoint Gas

Reference Cap

Pilot Pressure Port

Tri-Clamp Connection

Control Diaphragm

Regulator Body

Sealing Diaphragm

Bottom Cap

DIA
ME Passive Dampening Inserts1

Leak Detection Port

Sanitary Designed Crush Seal

1 Integrated passive dampening is standard in most models to help reduce possible downstream pressure fluctuations due to process equipment such as pumps.
Product Overview 20

Sanitary Safety Relief Valves

81V Series 83 Series

88 Series 83X Series 88 Series

National Board Certified to ASME VIII/XIII. Designed to relieve overpressure upset in hygienic and aseptic process
and clean utility systems. They are manually set to open at a predetermined pressure and re-seat after pressure
subsides. This protects pressure vessels and other equipment from pressure that exceeds their design limits.

» Bioreactor: fermenter vessel and vessel jackets » Clean steam systems

» Formulation and other pharma process vessels » WFI and USP PW vessels
» Clean air/gas distribution systems for point of use » Any hygienic or aseptic process vessel or system
Product Overview 21

SSRV 81/81V SERIES, SMALL CAPACITY

1/2" - 1" MNPT, FNPT (inlet); 1/2" - 1" FNPT (outlet)

Available Connection Size & Type
1/2" - 1" ASME BPE Tri-Clamp (inlet); 1/2" - 1" ASME BPE Tri-Clamp (outlet)
Body & Wetted Trim Materials ASME SA479 316L (UNS 31603), AL6XN, Hasteloy C-22, other materials
EPDM (o-ring soft seat & vulcanized soft seat) rated to 325°F (163°C)
Viton (o-ring soft seat) rated to 400°F (204°C)
FDA & USP Class VI Compliant Elastomers
Wetted Seat & O-Ring Material
EPDM (o-ring soft seat & vulcanized soft seat) rated to 325°F (163°C)
Viton (o-ring soft seat & vulcanized soft seat) rated to 400°F (204°C)
FFKM (o-ring soft seat) rated to 450°F (232°C)
Body Pressure/Temperature Rating 550 psi @ 450°F (37,9 bar @ 232°C)
Available Setpoint Range 15-232 psi (1,03 - 16 bar) Standard 81 Series; 233 - 500 psi (16,1 - 34,4 bar) High Pressure 81 Series

SSRV 83/83X SERIES, MEDIUM CAPACITY

1-1/2" ASME BPE Tri-Clamp (inlet); 2" ASME BPE Tri-Clamp (outlet) 83 Series;
Available Connection Size & Type
1" ASME BPE Tri-Clamp (inlet); 1-1/2" ASME BPE Tri-Clamp (outlet) 83X Series
Body & Wetted Trim Materials ASME SA479 316L (UNS 31603), AL6XN, Hasteloy C-22, other materials
FDA & USP Class VI Compliant Elastomers
EPDM rated -49°F to 302°F (-45°C to 150°C)
Wetted Seat & O-Ring Material
Viton rated to 400°F (204°C)
FFKM rated 32°F to 450°F (0° to 232°C)
Body Pressure/Temperature Rating 255 psi @ 450°F steam*, gas, liquid (17,6 bar @ 232°C) * up to 90 psi (6,2 bar)
Available Setpoint Range 15 - 232 (1,03 bar - 16 bar)

SSRV 88 SERIES, LARGE CAPACITY

1/2" - 1" MNPT, FNPT (inlet); 1/2" - 1" FNPT (outlet)

Available Connection Size & Type
1/2" - 1" ASME BPE Tri-Clamp (inlet); 1/2" - 1" ASME BPE Tri-Clamp (outlet)
Body & Wetted Trim Materials ASME SA479 316L (UNS 31603), AL6XN, Hasteloy C-22, other materials
FDA & USP Class VI Compliant Elastomers
EPDM rated -49°F to 302°F (-45°C to 150°C)
Wetted Seat & O-Ring Material
Viton rated to 400°F (204°C)
FFKM rated 32°F to 450°F (0° to 232°C)
Body Pressure/Temperature Rating 255 psi @ 450°F steam*, gas, liquid (17,6 bar @ 232°C) * up to 90 psi (6,2 bar)
Available Setpoint Range Water: 15 - 232 psi (1,03 - 16,0 bar); air/gas/steam: 20 - 232 psi (1,37 - 16,0 bar)
Product Overview 22

Sanitary Diaphragm Valves

Manual or air actuated forged 2-way or cast 2-way, ported and tandem valves. Barstock zero static T-block, point of
use T-block, divert tank bottom and custom block body valves.

» Well suited to control the flow of corrosive materials and avoid contamination of product within many processes around
clean utilities, WFI, and many purified water applications
» Ideal for industries that require a high degree of fluid purity and cleanliness in the pharmaceutical processing industries
Product Overview 23

VALVE TYPE BY APPLICATION

2-WAYS

PORTED

TANDEM ACCESS

ZERO STATIC T-BLOCK

ZERO STATIC POU

DIVERT BLOCK

TANK BOTTOM
Product Overview 24

Sanitary Check Valves

SVC Series

SHC Series

Two piece, spring-less horizontal line sanitary check valves and two piece, spring-less sanitary disc check valves for
vertical up-flow for bioprocess media and purified water applications for the biopharmaceutical, pharmaceutical,
and consumer health & beauty industries.

» WFI loop: non-return at pump out » Separation: centrifuge waste line back flow prevention
» Media/buffer prep: back flow prevention during dilution » Purification, chromatography: waste line back flow
» Upstream process: sparge line back flow prevention prevention
» Pump head pressure maintenance or pressure bypass
Product Overview 25

SVC SERIES, VERTICAL LINE UP-FLOW, LOW TO HIGH FLOW

Sizes 1/2" - 3" (DN15 - DN80)

End Connections ASME, DIN, ISO Tri-Clamp, and Tube Weld Ends
Cv (Kv) 3.5 - 58.6 (3,03 - 50,7 Kv)
Wetted SS Material ASTM A479 316L or optional DIN 1.4435
Disc Material 316/EPDM, Teflon, PEEK (all materials FDA and USP Class VI)
Gasket Material Various (all materials FDA and USP Class VI)
Max Pressure Temperature 230 psi @ 100°F (16 bar @ 38°C) max temperature dependent on disc and gasket material
Cracking (opening) Pressure Polymer DIscs: 0.04 psid (2,76 millibar); 316/EPDM: 0.13 psid (9,76 milibar)
Metallic Surface Finish Wetted parts: ASME BPE SF 20Ra (0,5 μm) electropolished; standard: 8 Ra (0,2 μm) electropolished optional

SVC SERIES, VERTICAL LINE DOWN, FOR DRAIN LINES, LOW TO HIGH FLOW

Sizes 1/2" - 3" (DN15 - DN80)

End Connections ASME, DIN, ISO Tri-Clamp, and Tube Weld Ends
Cv (Kv) 3.5 - 58.6 (3,03 - 50,7 Kv)
Wetted SS Material ASTM A479 316L or optional DIN 1.4435
Disc Material Polypropylene (all materials FDA and USP Class VI)
Gasket Material Various (all materials FDA and USP Class VI)
Max Pressure Temperature 230 psi @ 100°F (16 bar @ 38°C) max temperature dependent on disc and gasket material
Cracking (opening) Pressure Trap is always open, will only close if water based liquid rises in outlet drdain line
Metallic Surface Finish Wetted parts: ASME BPE SF 20Ra (0,5 μm) electropolished; standard: 8 Ra (0,2 μm) electropolished optional

SHC SERIES, HORIZONTAL LINE, LOW TO HIGH FLOW

Sizes 1/2" - 2" (DN15 - DN50)

End Connections ASME, DIN, ISO Tri-Clamp, and Tube Weld Ends
Cv (Kv) 3.4 - 23.1 (2,94 - 20 Kv)
Wetted SS Material ASTM A479 316L or optional DIN 1.4435
Disc Material 316/EPDM, Teflon, PEEK (all materials FDA and USP Class VI)
Gasket Material Various (all materials FDA and USP Class VI)
Max Pressure Temperature 230 psi @ 100°F (16 bar @ 38°C) max temperature dependent on disc and gasket material
Cracking (opening) Pressure Polymer DIscs: 0.04 psid (2,76 millibar); 316/EPDM: 0.13 psid (9,76 milibar)
Metallic Surface Finish Wetted parts: ASME BPE SF 20Ra (0,5 μm) electropolished; standard: 8 Ra (0,2 μm) electropolished optional
Product Overview 26

Sanitary Steam Traps & Accessories

Mark 93 Series SG & SGW Series Mark 9020 Series

SSC Series Mark 94 Series SC Series

Two piece tri-clamp body, balanced port, low to high flow, thermostatic sanitary steam traps with vertical or
horizontal inlet and outlet connections for pure steam SIP and loop drainage applications in biopharmaceutical and
certain consumer health and beauty industries.

» Up and downstream process vessel: small to medium sized vessel or large vessel bypass loop trap, validated SIP drainage
» Up and downstream process: validated and high flow validated SIP tubing drain
» Sterile filter: validated SIP condensate drain from filters; large vent and product filters validated SIP tubing drain
» Clean steam distribution loop: loop drainage and point of use PCV drainage
» Clean steam humidification drainage in air handlers
Product Overview 27

MARK 93 SERIES, MEDIUM TO HIGH FLOW, CLEAN STEAM TRAP

MARK 93JR SERIES, COMPACT, LOW TO MEDIUM FLOW, CLEAN STEAM TRAP
Sizes 1/2", 3/4", 1", 1-1/2" (DN15, DN20, DN25, DN40) MK93 Series; 1/4", 1/2", 3/4", 1" (DN8, DN15, DN20, DN25) MK93JR Series
Installation Connection Orientation Vertical, Horizontal (MK93 Series only)
Connection Type: ASME, DIN, ISO Tri-Clamp and Tube Weld Ends
Max Pressure/Temperature 145 psig @ 350°F (10 barg @ 177°C)
Max Recommended Differential Pressure 10 - 50 psi (0,7 - 3,4); Mark 93P option: 45 - 90 psi (3,1 - 6,2 bar) MK93 Series; 0 - 100 psi (0,7 - 6,9 bar) MK93JR
Wetted body/plug material: ASTM SA479 316L or optional DIN 1.4435; Body Gaskets: various, all FDA and
Materials of Construction
USP Class VI

Nominal Cv (Kv) 3.8 Cv (3,30 Kv) Mark 93 Series; Cold water 1.31 Cv (1,13 Kv) Mark 93JR Series

Subcooling Less than 3°F (1,7 °C) Mark 93 Series

MARK 94 SERIES, HIGH FLOW, CLEAN STEAM TRAP

Sizes 3/4", 1", 1-1/2" (DN20, DN25, DN40)

Installation Connection Orientation Vertical, Horizontal
Connection Type: ASME, DIN, ISO Tri-Clamp and Tube Weld Ends
Max Pressure/Temperature 145 psig @ 350°F (10 barg @ 177°C)
Max Recommended Differential Pressure 50 psi (3,4 bar)
Wetted body/plug material: ASTM SA479 316L or optional DIN 1.4435; Body Gaskets: various, all FDA and
Materials of Construction
USP Class VI
Nominal Cv (Kv) 4.0 Cv (3,4 Kv)
Subcooling Less than 3°F (1,7 °C)

MARK 9020 SERIES BALL VALVES

Sizes 1/2" - 4" (DN15 - DN100)

End Connections ASME BPE, Tri-Clamp or extended tube weld ends, DIN 11866-A or B (ISO) extended tube weld ends std
Max Pressure/Temperature to 1000 psig @ 100°F (68,9 barg @ 38°C); 500 psig @ 295°F (34, barg @1 146°C)
Seat & Seal Material TFM 1600 non-cavity filler seats and all seals FDA, USP <88> Class VI and USP <87>
ASTM SA351 CF3M with <3% or 1% ferrite SF1, 20 Ra (0,5μm) machined polished standard, SF4,
Wetted Material & Surface Finish
15 Ra (0,4μm) electropolish optionaloptional

SSC SERIES, CLEAN STEAM SUBCOOLED CONDENSER

Connection Size/Type 3/4" ASME BPE Tri-Clamp end connections

Max Operating Pressure 145 psig (10 barg) Note: drain system maximum operating pressure is determined by attached steam trap
Materials of Construction Wetted material: ASTM SA479 316L or DIN 1.4435
Capacity dependent on trap attached to outlet. Unit cools condensate before steam trap enabling the bellows
Surface Finish
to contract, opening orifice further
Radiant and Convective Heat Loss Cools entering condensate by an average 30°F at ambient temperatures

Please visit our website to see our full range of Clean Steam Traps & SIP Accessories
 A Division of Richards Industrials
3170 Wasson Road, Cincinnati, OH 45209

1.513.533.5600
steriflow@richardsind.com
steriflowvalve.com

A Division of Richards Industrials

320 Rutledge Road, Fletcher, NC 28732
1.828.650.6590
inquiry@equilibar.com
equilibar.com

SFCC/1024