Have Questions?

Quick Setup Guide Do not return to store. We can help.

Call Customer Service Toll-Free 1-877-224-0458
Pressure Washer or visit our website, www.usa.husqvarna.com

WARNING Failure to read and follow the WARNING Engine exhaust contains carbon
operator’s manual and all operating monoxide, a poisonous gas that could kill
instructions could result in death or you in minutes. You CANNOT smell it, see
serious injury. it, or taste it. Operate ONLY outside far
away from windows, doors and vents. Install carbon
WARNING Fuel and its vapors are extremely monoxide alarms. DO NOT run this product inside
flammable and explosive which could homes or garages, even if using fans or opening
cause burns, fire or explosion resulting doors and windows.
in death or serious injury. Turn pressure
washer engine OFF and let it cool at least 2 WARNING High water pressure could cut
minutes before removing fuel cap. Let spilled fuel through skin resulting in serious injury.
evaporate before starting engine. Always allow Spray gun traps high water pressure,
space for fuel expansion. even when engine is stopped and water
is disconnected. NEVER aim spray gun at people,
WARNING Starter cord kickback (rapid animals, or plants. ALWAYS point spray gun in
retraction) will pull hand and arm toward safe direction, press red button and squeeze spray
engine faster than you can let go which gun trigger to release high pressure, every time
could cause broken bones, fractures, you stop engine.
bruises, or sprains resulting in serious injury.
NEVER pull starter cord without first relieving WARNING Risk of eye injury. Spray could
spray gun pressure. Pull starter cord slowly until splash back or propel objects resulting
resistance is felt, then pull rapidly. Firmly grasp in serious injury. Always wear indirect
spray gun with both hands when using high vented (chemical splash) safety goggles
pressure spray to avoid injury when spray gun marked to comply with ANSI Z87.1 when using
kicks back. or in vicinity of this equipment. NEVER substitute
safety glasses or dry-condition goggles for indirect
vented safety goggles. Add engine oil and fuel 7
Items Included: Operator’s Manual and Oil Funnel (not shown) NOTICE You MUST properly fill engine with oil before attempting
to start pressure washer.
NOTICE DO NOT use unapproved gasoline such as E15 and
E85. DO NOT mix oil in gasoline or modify engine to run on
alternate fuels.
1. Move pressure washer outdoors to a flat, level surface.
2. Clean area around oil fill and remove oil fill cap ( ). 7
3. Using oil funnel, slowly pour contents of supplied oil into oil
fill opening to the point of overflowing at oil fill cap. DO NOT
8
OVERFILL.
4. Replace oil fill cap and fully tighten.
5. Clean area around fuel cap ( ), remove fuel cap. 8
6. Slowly add unleaded gasoline (P) to fuel tank (Q). Be careful
not to fill above the baffle (R). This allows adequate space for
fuel expansion as shown. 9
7. Install fuel cap and let any spilled fuel evaporate before
starting engine.

Move pressure washer to safe 9

operating location
Q
TANK

n
WARNING Engine exhaust contains carbon monoxide, a
poisonous gas that could kill you in minutes. You CANNOT
smell it, see it, or taste it. Operate ONLY outside far away
R
P
FUEL
io
from windows, doors and vents. Install carbon monoxide
You will need: alarms. DO NOT run this product inside homes or garages, even if
using fans or opening doors and windows.
• Utility knife • Unleaded fuel • 19 mm wrench • Garden hose, 50 ft. (15 m) or less 10
1. Running engines give off carbon monoxide.
• Safety goggles (indirect vented type) • Petroleum or synthetic grease
ct
2. Keep at least 5 ft. (1.5 m) clearance on all sides of pressure
washer including overhead to reduce the risk of exhaust heat
Unpack pressure washer
r

or exhaust gases igniting nearby combustible material. 10

1
3. Place lock levers on caster wheels in the ON (I) postion to lock
ep o
du

1. Remove everything from carton except pressure washer.

wheels and keep pressure washer from moving. 11
2. Open carton completely by cutting each corner from top to A
bottom.
Connect spray gun
R tf

3. Ensure you have all included items prior to assembly. B Exhaust

If items are damaged or missing, call 1-877-224-0458. NOTICE Remove and discard the shipping caps from the Port
Pointed
C pump’s high pressure outlet and water inlet before attaching
4. Prior to assembly, lubricate the rubber o-ring seals on
ro

away from
hoses.
all connections with petroleum or synthetic grease. See occupied
o

Operator’s Manual, Lubricate O-Rings. 12 13 14 16 17 1. Uncoil high pressure hose and attach quick connect end of spaces
hose (S) to base of spray gun (T). Pull down on collar of quick
2
Attach accessory holders connect, slide onto spray gun and let go of collar. Tug on hose 11
N

to be sure of tight connection. 12

All assembly instructions in this section will be viewing from E D
2. Similarly, attach other end of high pressure hose to high
engine end of unit.
pressure outlet (U) on pump. Push back on collar of quick
1. Place hose wrap (A) over holes (B) on end of main unit. Using connect, slide onto pump and let go of collar. Pull on hose to
provided hex key wrench, attach hose wrap with three screws be sure of tight connection. 13
(C). Tighten by hand. 1
2. Insert spray gun holder wireform (D) through holes on right
side of unit frame. Hold wireform in place and attach a plastic 3
Connect water supply
knob (E) from inside of unit. Tighten by hand. 2 1. Inspect garden hose inlet screen (V) for damage. 14
3. Using provided hex key wrench, attach metal spring clips (F)
F
NOTICE If inlet screen is damaged or missing, DO NOT use 12
to left side panel of unit with screws (G). Tighten by hand. 3 pressure washer, call 1-877-224-0458.
2. Clean screen if necessary. Refer to operator’s manual for
Install wheel kit instructions. T
S
1. Lift corner of pressure washer and slide caster wheels up 3. Run cold water through garden hose (W) for 30 seconds to
into bottom of tubing on each underside of pressure washer clean out any debris. Garden hose length must not exceed
frame. 4 G 50 ft. (15 m). Turn off water supply and attach garden hose to
water inlet (X). Tighten by hand. 14
2. Using a 19 mm wrench, turn nut (H) counterclockwise under
collar of caster wheels to tighten. 4 4
3. Slide flat washer (J), wheel (K) and another flat washer (J)
over axle stud (L). 5 13
NOTICE Be sure to install wheel with raised hub inboard.
4. Lift corner of pressure washer slightly and slide axle stud U
through mounting bracket on pressure washer frame.
5. Insert retaining pin (M) through hole on axle stud. 5 H
6. Repeat steps 3 through 5 to secure second wheel.
7. Screw handle pin (N) into bracket on left side of frame. 6 5
K
14
L
X V W

M J

6
N

Copyright © 2014. All rights reserved. No part of this material may be reproduced or transmitted in any form without the express written permission of Briggs & Stratton Power Products Group, LLC.
Every effort has been made to ensure that the information in this document is accurate and correct. However, we reserve the right to alter or otherwise improve the product and this document at any time without prior notice and without incurring obligation.
*This pressure washer is rated in accordance to the Pressure Washer Manufacturers Association (PWMA) standard PW101-2010 (Testing and Rating Performance of Pressure Washers). 316331, Rev B
Start pressure washer 15
9. Position yourself as recommended, grasp recoil handle and
pull slowly until slight resistance is felt. Then pull rapidly one 21
NOTICE You MUST connect and turn on water supply fully time only to start engine. Return recoil starter slowly. DO NOT
before starting engine. let rope “snap back” against starter. 21
Y
WARNING Risk of eye injury. Spray could splash back
WARNING Starter cord kickback (rapid retraction) will pull
or propel objects resulting in serious injury. Always
hand and arm toward engine faster than you can
wear indirect vented (chemical splash) safety goggles
let go which could cause broken bones, fractures,
marked to comply with ANSI Z87.1 when using or in
bruises, or sprains resulting in serious injury. NEVER
vicinity of this equipment. NEVER substitute safety glasses or
pull starter cord without first relieving spray gun pressure. Pull
dry-condition goggles for indirect vented safety goggles.
starter cord slowly until resistance is felt, then pull rapidly.
1. Put on safety goggles. Firmly grasp spray gun with both hands when using high
2. Turn on water supply. 16 pressure spray to avoid injury when spray gun kicks back.
3. Point spray gun in a safe direction, press the red safety button NOTICE After each starting attempt, where engine fails to
(Y) and squeeze trigger to purge pump system of air and run, always point spray gun in a safe direction, push red button
impurities. 15 and squeeze spray gun trigger to release retained high water
4. Attach nozzle extension (Z) to spray gun (T). Tighten by pressure.
hand. 16 10. When engine starts, slowly move choke lever (DD) to RUN ( )
5. Pull back on collar of nozzle extension (Z), insert spray tip (AA) T Z position , as engine warms. If engine falters, move choke lever
and release collar. Tug on spray tip to make sure it is securely to CHOKE ( ) position, then to RUN ( ) position. 20
in place. 17
17 11. If engine fails to start after six pulls, move choke lever to
RUN ( ) position, and repeat step 9.
6. Rotate fuel shut-off valve (BB) to ON (I) position. 18
7. Move throttle lever (CC) to FAST ( ) position. 19 NOTICE Always keep the throttle lever in the FAST ( ) position
AA when operating the pressure washer.
8. Move choke lever (DD) to CHOKE ( ) position. 20
Z 12. Point gun toward surface to be cleaned. Press the red safety
button and pull trigger to begin spraying.

Stop pressure washer

18 1. Release spray gun trigger and let engine idle for two minutes.
2. Move throttle lever (CC) to SLOW ( ) position, then
STOP ( ) position. 19
3. Rotate fuel shut-off valve (BB) to OFF (0) position. 18
BB 4. Turn off water supply.
5. Always point spray gun in safe direction, press the red safety
button, and squeeze spray gun trigger to relieve retained high
water pressure.
19 6. Disconnect garden hose from pump.
7. Disconnect high pressure hose from pump and gun for
CC storage. For long term storage instructions, see operator’s
manual.
8. Remove safety goggles.

20

DD

n
io
ct
r
ep o
du
R tf
ro
o
N