DRIVER CONTROLS

SECTION MIR MIRRORS

B

E
CONTENTS
PRECAUTION ............................................... 2 Exploded View .......................................................... 6 F
Removal and Installation .......................................... 6
PRECAUTIONS ................................................... 2
Precaution for Supplemental Restraint System DOOR MIRROR ................................................. 7
G
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- Exploded View .......................................................... 7
SIONER" ................................................................... 2
DOOR MIRROR ASSEMBLY ..................................... 9
Precautions Necessary for Steering Wheel Rota-
DOOR MIRROR ASSEMBLY : Removal and In- H
tion After Battery Disconnection ................................ 2
stallation ................................................................... 9
PREPARATION ............................................ 4 DOOR MIRROR ASSEMBLY : Disassembly and
Assembly .................................................................. 9
I
PREPARATION ................................................... 4
Commercial Service Tools ....................................... 4 GLASS MIRROR ......................................................... 9
GLASS MIRROR : Removal and Installation ...........10
WIRING DIAGRAM ....................................... 5 J
DOOR MIRROR COVER ...........................................10
DOOR MIRROR SYSTEM ................................... 5 DOOR MIRROR COVER : Removal and Installa-
Wiring Diagram ......................................................... 5 tion ...........................................................................10
K
REMOVAL AND INSTALLATION ................ 6 DOOR MIRROR REMOTE CONTROL
SWITCH ............................................................. 11
INSIDE MIRROR ................................................. 6 Removal and Installation .........................................11 MIR

Revision: 2012 August MIR-1 C26

 PRECAUTIONS
< PRECAUTION >
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER" INFOID:0000000008758305

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and
“SEAT BELT” of this Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precautions Necessary for Steering Wheel Rotation After Battery Disconnection
INFOID:0000000008758306

CAUTION:
Comply with the following cautions to prevent any error and malfunction.
• Before removing and installing any control units, first turn the ignition switch to the LOCK position,
then disconnect both battery cables.
• After finishing work, confirm that all control unit connectors are connected properly, then re-connect
both battery cables.
• Always use CONSULT to perform self-diagnosis as a part of each function inspection after finishing
work. If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.
For vehicle with steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock and
cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the operation pro-
cedure below before starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2. Turn the ignition switch to ACC position.
(At this time, the steering lock will be released.)
3. Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.
4. Perform the necessary repair operation.

Revision: 2012 August MIR-2 C26

 PRECAUTIONS
< PRECAUTION >
5. When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the ignition switch from ACC position to ON position, then to LOCK position. (The steering wheel will lock A
when the ignition switch is turned to LOCK position.)
6. Perform self-diagnosis check of all control units using CONSULT.
B

MIR

Revision: 2012 August MIR-3 C26

 PREPARATION
< PREPARATION >
PREPARATION
PREPARATION
Commercial Service Tools INFOID:0000000008758307

Tool name Description

Remover tool Removes the clips, pawls and metal clips

JMKIA3050ZZ

Revision: 2012 August MIR-4 C26

 DOOR MIRROR SYSTEM
< WIRING DIAGRAM >
WIRING DIAGRAM A
DOOR MIRROR SYSTEM
Wiring Diagram INFOID:0000000008758308
B

For connector terminal arrangements, harness layouts, and alphabets in a (option abbreviation; if not
described in wiring diagram), refer to GI-5, "Connector Information/Explanation of Option Abbreviation".
C

MIR

JRLWC2531JP

Revision: 2012 August MIR-5 C26

 INSIDE MIRROR
< REMOVAL AND INSTALLATION >
REMOVAL AND INSTALLATION
INSIDE MIRROR
Exploded View INFOID:0000000008758309

JMLIA1209ZZ

1. Windshield glass 2. Inside mirror base 3. Harness connector

4. Inside mirror 5. Inside mirror cover
: Always replace after every disassembly.

Removal and Installation INFOID:0000000008758310

REMOVAL
CAUTION:
• Never reuse the inside mirror removed from mirror base.
• Never use excessive force to remove the inside mirror because it is inserted tightly into the mirror
base.
INSTALLATION
CAUTION:
When inserting the inside mirror into the mirror base, be sure to push the pawl until it get connected to
the mirror base.

Revision: 2012 August MIR-6 C26

 DOOR MIRROR
< REMOVAL AND INSTALLATION >
DOOR MIRROR
A
Exploded View INFOID:0000000008758311

Models with around view camera and side turn signal lamp B

I
JMLIA1785ZZ

1. Door mirror cover 2. Around view camera assembly 3. Door mirror corner cover J
4. Door mirror base packing 5. Door mirror base 6. Glass mirror
7. Actuator 8. Side turn signal lamp 9. Housing assembly
10. Connector K
: Clip
: Pawl
MIR

Revision: 2012 August MIR-7 C26

 DOOR MIRROR
< REMOVAL AND INSTALLATION >
Models with side turn signal lamp only

JMLIA1786ZZ

1. Door mirror cover 2. Door mirror under cover 3. Door mirror corner cover
4. Door mirror base packing 5. Door mirror base 6. Glass mirror
7. Actuator 8. Side turn signal lamp 9. Housing assembly
10. Connector
: Clip
: Pawl

Revision: 2012 August MIR-8 C26

 DOOR MIRROR
< REMOVAL AND INSTALLATION >
Models without around view camera and side turn signal lamp
A

H
JMLIA1787ZZ

1. Door mirror cover 2. Door mirror corner cover 3. Door mirror base packing
4. Door mirror base 5. Glass mirror 6. Actuator I
7. Housing assembly 8. Connector
: Clip
J
: Pawl

DOOR MIRROR ASSEMBLY

K
DOOR MIRROR ASSEMBLY : Removal and Installation INFOID:0000000008758312

REMOVAL MIR
CAUTION:
• When removing, always use a remover tool that is made of plastic.
• Be careful not to damage the mirror body. M
INSTALLATION
CAUTION:
Perform camera image calibration for models with around view camera. N
DOOR MIRROR ASSEMBLY : Disassembly and Assembly INFOID:0000000008758313

CAUTION: O
When disassembling, always use a remover tool that is made of plastic.
Assembly
CAUTION: P
• Perform camera image calibration for models with around view camera.
• Visually check that the harness terminals are correctly inserted into the connector according to the
harness layout.

GLASS MIRROR

Revision: 2012 August MIR-9 C26

 DOOR MIRROR
< REMOVAL AND INSTALLATION >
GLASS MIRROR : Removal and Installation INFOID:0000000008758314

REMOVAL
CAUTION:
Apply protective tape around housing to protect the painted surface from damage.
INSTALLATION
CAUTION:
Visually check that the mirror heater harness terminals are correctly inserted into the connectors (with
mirror heater models only).
DOOR MIRROR COVER
DOOR MIRROR COVER : Removal and Installation INFOID:0000000008758315

CAUTION:
When removing, always use a remover tool that is made of plastic.
INSTALLATION
CAUTION:
After installation, visually check that pawls are securely engaged.

Revision: 2012 August MIR-10 C26

 DOOR MIRROR REMOTE CONTROL SWITCH
< REMOVAL AND INSTALLATION >
DOOR MIRROR REMOTE CONTROL SWITCH
A
Removal and Installation INFOID:0000000008758316

REMOVAL B
CAUTION:
Never fold the pawl of instrument lower panel RH.
C

MIR

Revision: 2012 August MIR-11 C26