DAC basic/classic

Parameter list
969
0791 969901

VB02.6
All rights reserved.
Property of Dürkopp Adler GmbH and protected by copyright. Any reuse of
these contents, including extracts, is prohibited without the prior written ap-
proval of Dürkopp Adler GmbH.
Copyright © Dürkopp Adler GmbH 2022
Parameter list

Table of Contents
1 Parameter ........................................................................................................... 5
1.1 Operator level ..................................................................................................... 5
Bobbin stitch counter/ remaining thread monitor/piece counter .......................... 5
Needle cooling/fan .............................................................................................. 6
Light barrier ......................................................................................................... 6
Stitch loosening device ....................................................................................... 6
1.2 Technician level .................................................................................................. 7
Thread clamp (TC) ............................................................................................ 10
Thread cutter (FA)............................................................................................. 12
Sewing foot lift (FL) ........................................................................................... 13
Soft start ........................................................................................................... 14
Remaining thread monitor/bobbin rotation monitor/skip stitch detector............. 14
Needle thread monitor up ................................................................................. 14
Needle thread monitor down ............................................................................. 15
Seam paths ....................................................................................................... 15
Motor ................................................................................................................. 15
Thread tension .................................................................................................. 18
Stroke adjustment ............................................................................................. 20
Function module ............................................................................................... 21
Reversal ............................................................................................................ 24
Needle cooling/fan ............................................................................................ 24
Carrier roller/puller/seam middle guide ............................................................. 25
Edge cutter ....................................................................................................... 27
Light barrier ....................................................................................................... 27
Electronic handwheel ........................................................................................ 28
Stacker.............................................................................................................. 28
Zigzag ............................................................................................................... 29
Thread wiper ..................................................................................................... 29
Step cutting/contour guide ................................................................................ 29
Outfeed roller .................................................................................................... 29
Hook lubrication ................................................................................................ 29
Stitch loosening device ..................................................................................... 30
Tape Cutter ....................................................................................................... 30
Stitch length switching ...................................................................................... 31
Stitch shortening ............................................................................................... 31
Operation lock ................................................................................................... 31
Control, other .................................................................................................... 31

DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022 3

 Parameter list

OP1000 ............................................................................................................. 38
1.3 Developer level ................................................................................................. 40
Thread cutter (FA)............................................................................................. 40
Seam paths ....................................................................................................... 41
Motor ................................................................................................................. 41
Thread tension .................................................................................................. 42
Top puller .......................................................................................................... 42
Bottom puller ..................................................................................................... 43
Control, other .................................................................................................... 44
2 Error, warning and information messages ........................................................ 47

4 DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022

Parameter list

1 Parameter
The parameter list helps the user quickly locate and change a parameter.
Some parameters have been grouped into categories which can be found on sev-
eral levels and reflect their importance and their resulting minor or major effect on
the sewing behavior of the machine.

Class parameters 969

Class: 969
Parameter set:
For subclasses: 969-190180

1.1 Operator level

E C P Min Max Preset Unit Description
value
Bobbin stitch counter/ remaining thread monitor/piece counter
o 06 00 0 4 0 - Bobbin stitch counter / remaining
thread monitor
0 = Off;
1 = Bobbin stitch counter A;
2 = Bobbin stitch counter B;
3 = Bobbin stitch counter C;
4 = Remaining thread monitor
o 06 01 1 9999 3000 x o0604 Reset value of bobbin stitch
counter A
o 06 02 1 9999 2000 x o0604 Reset value of bobbin stitch
counter B
o 06 03 1 9999 1000 x o0604 Reset value of bobbin stitch
counter C
o 06 04 1 255 10 x stitches Factor of bobbin stitch counters
A, B and C
o 06 05 0 9999 0 Stitches Number of stitches for the re-
maining thread monitor
o 06 06 0 1 1 - Stop sewing motor when the
counter reaches 0
0 = Off;
1 = On
o 06 07 0 1 1 - Sewing foot stays down after
thread cutting
0 = Off;
1 = On
o 06 08 0 1 0 - When a counter has elapsed, a
reset must occur after thread
cutting
0 = Off;
1 = On

DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022 5

 Parameter list

E C P Min Max Preset Unit Description

value
o 06 10 0 1 0 - Display of the piece counter
0 = Off;
1 = On
o 06 20 0 1 0 - Needle thread monitor up
0 = Off;
1 = On
o 06 30 0 1 0 - Needle thread monitor down
0 = Off;
1 = On
Needle cooling/fan
o 13 00 0 1 0 - Needle cooling
0 = Off;
1 = On
Light barrier
o 16 00 0 255 0 Stitches Equalizing stitches for normal
stitch length
o 16 01 0 255 0 Stitches Equalizing stitches for long stitch
length
o 16 10 1 255 1 Seams Number of light barrier seams
o 16 20 0 255 0 Stitches Equalizing stitches for knitted
garment filter
Stitch loosening device
o 25 00 0 2 0 - Mode of automatic stitch loosen-
ing device
0 = Only stitch loosening;
1 = Stitch loosening and 2nd
stitch length;
2 = Stitch loosening, 2nd stitch
length, and quick stroke adjust-
ment;

6 DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022

Parameter list

1.2 Technician level

E C P Min Max Preset Unit Description
value
Bartack
t 00 00 300 6000 500 rpm Start bartack speed
t 00 01 0 254 5 10° Feed-forward angle when the
bartack magnet is switched on
(Switching from forward to back-
ward during bartacking)
t 00 02 0 254 17 10° Forward-feed angle when the
bartack magnet is switched off
(Switching from backward to
forward during bartacking)
t 00 03 0 1 0 - Start bartack can be interrupted
by setting pedal to 0 position
0 = Off;
1 = On
t 00 04 0 2 0 - Mode for end of start bartack
0 = Sewing continues after end;
1 = Machine stops and must be
restarted using the pedal;
2 = Thread cutting after start
bartack
t 00 05 0 1 1 - Pedal release only after addition-
al A path
0 = Off;
1 = On
t 00 06 0 500 0 ms Delay time to speed release after
start bartack
t 00 07 0 255 0 ms Fall time of bartack magnet
t 00 09 0 1 0 - Additional forward path at start
bartack with the number of back-
ward stitches
0 = Off;
1 = On
t 00 10 300 6000 500 rpm End bartack speed
t 00 11 0 254 9 10° Feed-forward angle when the
bartack magnet is switched on
(Switching from forward to back-
ward during bartacking)
t 00 12 0 254 17 10° Forward-feed angle when the
bartack magnet is switched off
(Switching from backward to
forward during bartacking)

DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022 7

 Parameter list

E C P Min Max Preset Unit Description

value
t 00 13 0 1 0 - Bartack magnet stays switched
on during the last backward path
(simple end bartack and multiple
end bartack) until position 2 has
been reached
0 = Off;
1 = On
t 00 19 0 1 0 - Additional forward path at end
bartack with the number of back-
ward stitches
0 = Off;
1 = On
t 00 20 300 6000 500 rpm Multiple start bartack speed (only
during darning program)
t 00 21 0 254 16 10° Feed-forward angle when the
bartack magnet is switched on
(Switching from forward to back-
ward during bartacking) (only
during darning program)
t 00 22 0 254 22 10° Forward-feed angle when the
bartack magnet is switched off
(Switching from backward to
forward during bartacking) (only
for darning program)
t 00 23 0 3 0 - Multiple start bartack as darning
program
0 = Off;
1 = On
t 00 24 0 1 0 - Pedal-dependent speed for
darning program
0 = Off;
1 = On
t 00 25 0 1 0 - First path with different number of
stitches (C) in multiple start
bartack
0 = Off;
1 = On
t 00 26 0 1 0 - Last path with different number of
stitches (B) in multiple end
bartack
0 = Off;
1 = On
t 00 30 0 1 1 - Ornamental-stitch bartack
0 = Off;
1 = On
t 00 31 0 2500 500 rpm Speed of ornamental-stitch
bartack
t 00 32 0 1000 100 ms Ending time during ornamental-
stitch bartack

8 DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022

Parameter list

E C P Min Max Preset Unit Description

value
t 00 35 0 1 1 - Speed decrease when feed dog
is repositioned
0 = Off;
1 = On
t 00 36 0 6000 500 rpm Level to which the speed is
supposed to be reduced when
the feed dog is repositioned
t 00 40 0 2 1 - Type of start bartack when the
bartack activation switch is en-
gaged
0 = Simple start bartack;
1 = Double start bartack;
2 = Multiple start bartack
t 00 41 0 2 1 - Type of end bartack when the
bartack activation switch is en-
gaged
0 = Simple end bartack;
1 = Double end bartack;
2 = Multiple end bartack
t 00 44 0 3 0 - Handling of manual bartack
0 = Manual bartack engages
immediately;
1 = Manual bartack engages
depending on parameters t
00 45 and t 00 46;
2 = During manual bartacking,
the drive stops in the posi-
tion set under parameters
t 00 45 and t 00 46;
3 = During manual bartack-
ing, the drive stops in the
position set under pa-
rameters t 00 45 and
t 00 46
(only if parameter t 00 30 =
1)
t 00 45 0 1 0 - Switch on the manual bartack
0 = Needle down;
1 = Needle up
t 00 46 0 1 0 - Switch off the manual bartack
0 = Needle down;
1 = Needle up
t 00 47 0 3 0 - Speed limit for manual bartack
0 = Off;
1 = Limit to DB3000 if
t 00 44 = 0 – 1
2 = Limit to ornamental-stitch
bartack speed
if t 00 44 = 2 – 3

DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022 9

 Parameter list

E C P Min Max Preset Unit Description

value
t 00 50 0 999 100 ms Activation time of bartack magnet
in period t1
t 00 51 5 100 100 % Duty cycle in period t1
t 00 52 0,0 600,0 0,0 s Activation time of bartack magnet
in period t2 (if 0, the bartack
magnet remains continuously
switched on)
t 00 53 5 100 100 % Duty cycle in period t2
t 00 54 0 1 0 - Increase in Umag when the
bartack magnet is activated
0 = No;
1= Yes
t 00 60 0 359 73 ° Angle at which the feed dog
repositioner is to supposed
switch
t 00 61 0 200 14 ms Switch on inertia
t 00 62 0 200 16 ms Switch off inertia
t 00 63 0 1 0 - Switch feed dog repositioner
depending on angle
0 = No;
1= Yes
t 00 70 0 255 0 Stitches Catch Backtack forward
t 00 71 0 255 0 Stitches Catch Backtack backward
Thread clamp (TC)
t 01 00 0 10 8 - Mode of thread clamp
0 = TC switch-on angle =
t 01 01,
TC switch-off angle =
t 01 02,
Without FL;
1 = TC switch-on angle = 108°,
TC switch-off angle = 268°,
Without FL;
2 = TC switch-on angle = 49°,
TC switch-off angle = 110°,
Without FL;
3 = TC switch-on angle = 49°,
TC switch-off angle = 190°,
Without FL;
4 = TC switch-on angle = 108°,
TC switch-off angle = 268°,
FL switch-on angle = 108°,
FL switch-off angle = 154°;
5 = TC switch-on angle = 108°,
TC switch-off angle = 268°,
FL switch-on angle = 44°,
FL switch-off angle = 154°;

10 DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022

Parameter list

E C P Min Max Preset Unit Description

value
6 = TC switch-on angle = 75°,
TC switch-off angle = 215°,
FL switch-on angle = 60°,
FL switch-off angle = 120°,
FL switch-off angle, addi-
tionally stroke-dependent;
7 = Without TC,
FL switch-on angle =
t 01 11,
FL switch-off angle =
t 01 12,
8 = TC switch-on angle =
t 01 01,
TC switch-off angle =
t 01 02,
FL switch-on angle =
t 01 11,
FL switch-off angle FL =
t 01 12;
9 = Without TC,
FL switch-on angle =
t 01 11,
FL switch-off angle =
t 01 12,
FL switch-off angle, addi-
tionally stroke-dependent;
10 = TC switch-on angle =
t 01 01,
TC switch-off angle =
t 01 02,
FL switch-on angle =
t 01 11,
FL switch-off angle =
t 01 12,
FL switch-off angle, addi-
tionally stroke-dependent;
t 01 01 0 359 75 ° Switch-on angle of thread clamp
t 01 02 0 359 215 ° Switch-off angle of thread clamp
t 01 11 0 359 60 ° Switch-on angle of sewing foot lift
t 01 12 0 359 120 ° Switch-off angle of sewing foot lift
t 01 13 0 100 100 % Duty cycle of sewing foot lift in
mode 4-8

DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022 11

 Parameter list

E C P Min Max Preset Unit Description

value
t 01 20 0 3 3 - Thread clamp options
0 = Thread clamp only at seam
beginning;
1 = Thread clamp at seam begin-
ning and during reverse;
2 = Thread clamp at seam begin-
ning and during sewing foot lift;
3 = Thread clamp at seam begin-
ning and during reverse and
sewing foot lift
t 01 30 0 2 0 - Neat seam beginning (NSB)
0 = Off;
1 = On when thread clamp is
active (old mode);
2 = On when thread clamp is
active (new mode)
t 01 31 0 9999 92 ° / ms Switch-on angle of additional
thread clamp (o.m.) / Switch-on
time knife (n.m.)
t 01 32 0 9999 201 ° Switch-off angle of additional
thread clamp
t 01 33 0 9999 105 ° Switch-on angle of thread ad-
vancing device
t 01 34 0 9999 203 ° / 10 ms Switch-off angle of thread ad-
vancing device (o.m.) / Time
duration of suction (n.m.)
t 01 35 0 9999 62 ° Switch-on angle of thread tension
lift
t 01 36 0 9999 94 ° Switch-off angle of thread tension
lift
t 01 50 0 999 100 ms Activation time of thread clamp in
period t1
t 01 51 5 100 100 % Duty cycle in period t1
t 01 52 0,1 120,0 60,0 s Activation time of thread clamp in
period t2 (if 0, the thread clamp
remains continuously switched
on)
t 01 53 5 100 30 % Duty cycle in period t2
t 01 54 0 1 0 - Increase in Umag when the thread
clamp is activated
0 = No;
1= Yes
Thread cutter (FA)
t 02 00 50 750 75 rpm Speed when cutting the thread
t 02 01 0 1 0 - Pedal position for initiating the
cutting process
0 = Position -2;
1 = Position -1

12 DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022

Parameter list

E C P Min Max Preset Unit Description

value
t 02 02 0 1 0 - Initiate seam end at seam begin-
ning (with single stitch functions
activated)
0 = No;
1= Yes
t 02 10 0 359 33 ° Switch-on angle t 08 12 <= t 02
10 < t 02 11
t 02 11 0 359 170 ° Switch-off angle t 02 10 < t 02 11
<= t 08 13
t 02 20 0 255 0 ms Delay time for repeated switch-on
of thread cutting magnet
t 02 21 0 255 0 ms Delay time for switch-off of thread
cutting magnet
t 02 50 0 999 500 ms Activation time of thread cutter in
period t1
t 02 51 5 100 100 % Duty cycle in period t1
t 02 52 0,1 120,0 10,0 s Activation time of thread cutter in
period t2 (if 0, the thread clamp
remains continuously switched
on)
t 02 53 5 100 100 % Duty cycle in period t2
t 02 54 0 1 0 - Increase in Umag when thread
cutter is activated
0 = No;
1= Yes
t 02 55 0 359 250 ° Angle at which duty cycle 2 is
activated (0 = deactivated)
Sewing foot lift (FL)
t 03 00 0 1 1 - Sewing foot lift
0 = Off;
1 = On
t 03 01 0 1 0 - No sewing start over push-botton
while the sewing foot is lifted
0 = Off;
1 = On
t 03 10 0 9999 80 ms Startup delay of machine after
sewing foot lift is switched off
t 03 11 0 255 40 ms Activation delay of sewing foot lift
during a machine standstill
t 03 12 0,0 9,999 0,600 s Activation delay of sewing foot lift
at seam end
t 03 50 0 999 200 ms Activation time of sewing foot lift
magnet in period t1
t 03 51 5 100 100 % Duty cycle in period t1
t 03 52 0,0 600,0 0,0 s Activation time of sewing foot lift
magnet in period t2 (if 0, the
sewing foot lift magnet remains
continuously switched on)

DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022 13

 Parameter list

E C P Min Max Preset Unit Description

value
t 03 53 5 100 100 % Duty cycle in period t2
t 03 54 0 1 0 - Increase in Umag when sewing
foot lift magnet is activated
0 = No;
1= Yes
t 03 55 0 1 0 - Activation sound warning before
foot is automatically lowered
0 = No;
1 = Yes
Soft start
t 05 00 120 1000 200 rpm Soft start speed
t 05 01 1 99 1 Stitches Number of soft start stitches
Remaining thread monitor/bobbin rotation monitor/skip stitch detector
t 06 00 0 2 0 - Activation of the remaining thread
monitor
0 = Off;
1 = Right;
2 = Left & right;
t 06 01 0 1 0 - Remaining thread monitor mode
0 = Dynamic;
1 = Static;
t 06 02 0,0 3,300 0,0 V Threshold right
t 06 03 0,0 3,300 0,0 V Intensity right
t 06 04 0,0 3,300 0,0 V Threshold left
t 06 05 0,0 3,300 0,0 V Intensity left
t 06 06 0 1 0 - Confirmation necessary by mes-
sages
0 = no;
1 = yes
t 06 10 0 1 0 - Skip stitch detector
(Not if t 06 00 = 2)
0 = Off;
1 = On
t 06 11 0 1 0 - Bobbin rotation monitor
(Not if t 06 00 = 2)
0 = Off;
1 = On
t 06 12 0 255 0 Stitches Number of stitches at which the
bobbin rotation monitor is acti-
vated
t 06 13 0 5000 0 ms Cleaning time SSD after FA
Needle thread monitor up
t 06 20 0 1000 180 rpm Speed at which the monitor is
activated

14 DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022

Parameter list

E C P Min Max Preset Unit Description

value
t 06 21 0 255 2 Stitches Number of stitches at which the
monitor is activated
t 06 22 0 1000 3 ms Debouncing
Needle thread monitor down
t 06 30 0 1000 180 rpm Speed at which the monitor is
activated
t 06 31 0 255 2 Stitches Number of stitches at which the
monitor is activated
t 06 32 0 1000 3 ms Debouncing
Seam paths
t 07 00 0 2 0 - Handling of position -2 for seam
paths
0 = Cancellation of the seam.
The next seam path is
sewn; the last seam of the
program is canceled with
thread cutting;
1 = Termination of the seam
with thread cutting (even if
not active). The next seam
procedure is a free seam;
2 = Termination of the seam
with thread cutting (even if
not active). Seam program
is canceled
t 07 01 0 1 0 - Automatic mode
0 = Off;
1 = On
t 07 02 0 1 0 - Signal on switch of path
0 = Off;
1 = On
t 07 03 0 1 0 - Repair mode
0 = Off;
1 = On
t 07 04 0 1 0 - Mode for cycling the sewing
program
0 = Off;
1 = On
t 07 05 0 1 0 - Possibility to start sewing from
the edited segment
0 = Off;
1 = On
Motor
t 08 00 500 9999 1000 rpm Maximum speed
t 08 01 10 400 75 rpm Minimum speed
t 08 02 10 1000 75 rpm Positioning speed

DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022 15

 Parameter list

E C P Min Max Preset Unit Description

value
t 08 03 1 100 10 rpm/ms Acceleration ramp
t 08 04 1 100 10 rpm/ms Deceleration ramp
t 08 05 0 1 0 - Direction of rotation of motor
0 = Left;
1 = Right
t 08 06 0 2 1 - Motor brake during normal stop
0 = Braking for period of t 08 09;
1 = Brake continuously active
when stopped;
2 = Position is continuously
maintained
t 08 07 0,1 6,0 0,7 A No-damage current when ma-
chine down
t 08 08 0 255 30 - Response time to changes in
position
t 08 09 0 999 200 ms Duration of motor brake
t 08 10 - - - - Reference position
t 08 11 - - - - Needle positions
t 08 12 0 359 115 ° Needle in the low position (bot-
tom dead center) (position 1)
t 08 13 0 359 310 ° Thread lever at top dead center
(position 2)
t 08 14 0 359 163 ° Point position
t 08 15 0 359 213 ° Threading position (needle
thread)
t 08 16 0 1 0 - Drive to bearing position via
pedal
t 08 19 1 9999 359 - Transmission ratio =
(motor diameter / machine diam-
eter) * 1000
t 08 20 - - - - Calibrate pedal
t 08 21 1 64 24 Levels Number of speed levels of pedal
t 08 22 0 7 3 - Speed curve
t 08 23 1 255 90 ms Debouncing of position -1
t 08 24 1 255 15 ms Debouncing of position -2
t 08 25 0 1 0 - Selection of pedal
0 = Analog;
1 = Digital
t 08 26 0 1 0 - Inverting signals of the digital
pedal
0 = No;
1 = Yes (Efka pedal with adapter)

16 DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022

Parameter list

E C P Min Max Preset Unit Description

value
t 08 27 0 2 0 - Handling of position -1 (only with
digital pedal)
0 = Not stored;
1 = Stored;
2 = Stored after Thread Trim, not
stored after sewstart
t 08 28 40 70 60 - Factor of position -1
This parameter can be used to
adjust the response between -1
and 0
t 08 29 20 70 49 - Factor of position -2
This parameter can be used to
adjust the response between -2
and 0
t 08 30 0 1 0 - Display of speed
0 = Off;
1 = On
t 08 31 0 1 0 - Display of current position
0 = Off;
1 = On
t 08 32 0 1 0 - After power-on and a tap on the
pedal, the needle is moved to the
"Needle up" position
0 = No;
1= Yes
t 08 33 0 6 0 - Output of position signals (signal
must be assigned to an output,
e.g. t 51 50)
0 = No signals are output;
1 = Pos. 1;
2 = Pos. 2;
3 = Pos. 1 & Pos. 2;
4 = Motor operation signal;
5 = Motor operation signal &
Pos. 1;
6 = Motor operation signal &
Pos. 2
t 08 34 0 255 0 ° Angle for the length of the Pos. 1
signal
t 08 35 0 255 0 ° Angle for the length of the Pos. 2
signal
t 08 36 10 9999 10 rpm Speed at which the motor opera-
tion signal is activated
t 08 37 0 359 0 ° Position 3 (only output position)
t 08 38 0 255 0 ° Angle for the length of the Pos. 3
signal ( > 0 output is activated)
t 08 40 150 9999 800 rpm Speed limit DB3000
t 08 41 150 9999 1800 rpm Speed limit DB2000

DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022 17

 Parameter list

E C P Min Max Preset Unit Description

value
t 08 44 1 255 40 ms Debouncing of position 0
t 08 50 10 500 180 rpm Preset speed value for single
stitch functions (half or full stitch,
etc.)
t 08 51 1 6000 180 rpm Speed for manual sewing per
push button
t 08 52 0 1 0 - Sewing functions via push button
also in manual mode
0 = No;
1= Yes
t 08 60 0 64 0 Level Shifting of position 1
Number of speed levels is re-
duced
Thread tension
t 09 00 0 3 2 ° Mode of thread tension and
thread tension reduction when
sewing foot lift is active
0 = no thread tension lift;
1 = Thread tension lift in the
seam;
2 = Thread tension lift after
thread cutting;
3 = Thread tension lift in the
seam and after thread cutting
t 09 01 0 1 0 ° Thread tension with threader
(needle thread) lifted
0 = No;
1= Yes
t 09 02 0,0 2,55 1,00 s Activation delay of thread tension
lift after thread cutting when
sewing foot is lifted (only active if
t 09 00 = 2 or 3)
t 09 03 0 2 0 ° Coupling of additional thread
tension with quick stroke adjust-
ment
0 = no coupling;
1 = Additional thread tension
during quick stroke adjustment;
2 = Additional thread tension
when quick stroke adjustment
speed is reached
t 09 10 0 359 175 ° Switch-on angle t 08 12 <= t 09
10 < t 09 11 during cutting pro-
cess
t 09 11 0 359 280 ° Switch-off angle t 09 10 < t 09 11
<= t 08 13 during cutting process
t 09 20 0 255 0 ms Delay time for repeated switch-on
of thread tension magnet during
cutting process

18 DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022

Parameter list

E C P Min Max Preset Unit Description

value
t 09 21 0 255 50 ms Delay time for switch-off of thread
tension magnet
t 09 30 0 1 0 - Open additional thread tension
during start bartacking
0 = No;
1 = Yes;
t 09 31 0 1 0 - Open additional thread tension
during end bartacking
0 = No;
1 = Yes;
t 09 32 0 1 0 - Open additional thread tension
during manual bartacking
0 = No;
1 = Yes;
t 09 33 0 1 0 - Open additional thread tension
for thread clamp
0 = No;
1 = Yes;
t 09 34 0 1 0 - Open additional thread tension
during soft start
0 = No;
1 = Yes;
t 09 35 0 1 0 - Open additional thread tension
during stitch shortening
0 = No;
1 = Yes;
t 09 36 0 1 0 - Open additional thread tension
during quick stroke adjustment
0 = No;
1 = Yes;
t 09 37 0 1 0 - Open additional thread tension
during single stitch functions
0 = No;
1 = Yes;
t 09 50 0 999 100 ms Activation time of thread tension
magnet in period t1
t 09 51 5 100 100 % Duty cycle in period t1
t 09 52 0,0 600,0 0,0 s Activation time of thread tension
magnet in period t2. (if 0, the
thread tension magnet remains
continuously switched on)
t 09 53 5 100 100 % Duty cycle in period t2
t 09 54 0 1 0 - Increase in Umag when the thread
tension magnet is activated
0 = No;
1= Yes

DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022 19

 Parameter list

E C P Min Max Preset Unit Description

value
Stroke adjustment
t 10 00 0 1 0 - Stroke adjustment
0 = No;
1= Yes
t 10 01 0 9999 600 rpm Stroke adjustment speed
t 10 02 1 21 5 Level Lower threshold
t 10 03 1 21 14 Level Upper threshold
t 10 04 - - - - Display of current level and
corresponding speed,
e. g. 3: 2800
3: = current level
2800 = corresponding speed
t 10 06 0 1 0 - Speed limit during quick stroke
adjustment
0 = Limitation of speed to stroke
adjustment speed for 500 ms;
1 = Continuous limitation of
speed to stroke adjustment
speed
t 10 07 0,0 2,55 0,0 s Stopping time of stroke adjust-
ment speed
t 10 08 0 255 0 Stitches Number of stitches for automatic
switch-off of quick stroke adjust-
ment (when 0, quick stroke ad-
justment is deactivated)
t 10 09 0 1 0 - Type of quick stroke adjustment
potentiometer
0 = 9880 867105;
1 = 9880 867119
t 10 10 0 9999 0 rpm Automatic of activa-
tion/deactivation of quick stroke
adjustment
Quick stroke adjustment activat-
ed  n < t 10 10
Quick stroke adjustment deac-
tivated  n >= t 10 10
Stored stroke adjustment is
deactivated

20 DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022

Parameter list

E C P Min Max Preset Unit Description

value
Function module
t 11 00 0 16 2 - Function of function module 1
(X1.30)
0 = No function;
1 = Additional thread tension;
2 = Stitch length switching;
3 = Single stitch with stitch
length switching;
4 = Single backward stitch with
stitch length switching;
5 = Raise/lower carrier roll-
er/seam middle guide/puller;
6 = Raise/lower edge stop;
7 = Raise/lower edge cutter;
8 = Stitch length switching
(Triflex) with DB2000 speed
limit and bartack suppres-
sion;
9 = Fullness with DB3000 speed
limit;
10 = Fullness without DB3000
speed limit;
11 = Step cutting;
12 = Contour guide;
13 = Stacker;
14 = Output function;
15 = Tape cutter;
16 = Biphasic edge cutter
t 11 01 0 1 0 - Invert output of function module 1
(X1.30)
0 = No;
1= Yes
t 11 02 1 3 1 - Condition of function module 1
(X1.30) after thread cutting
1 = Unchanged;
2 = Deactivated;
3 = Activated
t 11 03 1 3 1 - Condition of function module 1
(X1.30) after power on
1 = Unchanged;
2 = Deactivated;
3 = Activated
t 11 04 0 1 0 - Function module stored (only if
t 11 00 = 14)
0 = Stored;
1 = Not Stored

DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022 21

 Parameter list

E C P Min Max Preset Unit Description

value
t 11 05 0 2 0 - Type of activation delay of func-
tion module 1 (X1.30) (only if t 11
00 = 14)
0 = Time
1 = Stitches
2 = Bracket
t 11 06 0 9999 0 s or Activation delay
stitches
or °
t 11 07 0 2 0 - Type of switch-off delay of func-
tion module 1 (X1.30)
0 = Time
1 = Stitches
2 = Bracket
t 11 08 0 9999 0 s or Switch-off delay
stitches
or °
t 11 09 1 3 1 - Condition of function module 1
(X1.30) before thread cutting
1 = Unchanged;
2 = Deactivated;
3 = Activated
t 11 30 0 16 1 - Function of function module 2
(X1.20)
For function see t 11 00
t 11 31 0 1 0 - Invert output of function module 2
(X1.20)
0 = No;
1= Yes
t 11 32 1 3 1 - Condition of function module 2
(X1.20) after thread cutting
1 = Unchanged;
2 = Deactivated;
3 = Activated
t 11 33 1 3 1 - Condition of function module 2
(X1.20) after power on
1 = Unchanged;
2 = Deactivated;
3 = Activated
t 11 34 0 1 0 - Function module stored (only if
t 11 30 = 14)
0 = Stored;
1 = Not Stored
t 11 35 0 2 0 - Type of activation delay of func-
tion module 1 (X1.20) (only if t 11
30 = 14)
0 = Time
1 = Stitches
2 = Bracket

22 DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022

Parameter list

E C P Min Max Preset Unit Description

value
t 11 36 0 9999 0 s or Activation delay
stitches
or °
t 11 37 0 2 0 - Type of switch-off delay of func-
tion module 1 (X1.20)
0 = Time
1 = Stitches
2 = Bracket
t 11 38 0 9999 0 s or Switch-off delay
stitches
or °
t 11 39 1 3 1 - Condition of function module 2
(X1.20) before thread cutting
1 = Unchanged;
2 = Deactivated;
3 = Activated
t 11 60 0 16 0 - Function of function module 3
(X1.15)
For function see t 11 00
t 11 61 0 1 0 - Invert output of function module 3
(X1.15)
0 = No;
1= Yes
t 11 62 1 3 1 - Condition of function module 3
(X1.15) after thread cutting
1 = Unchanged;
2 = Deactivated;
3 = Activated
t 11 63 1 3 1 - Condition of function module 3
(X1.15) after power on
1 = Unchanged;
2 = Deactivated;
3 = Activated
t 11 64 0 1 0 - Function module stored (only if
t 11 60 = 14)
0 = Stored;
1 = Not Stored
t 11 65 0 2 0 - Type of activation delay of func-
tion module 1 (X1.15) (only if t 11
60 = 14)
0 = Time
1 = Stitches
t 11 66 0 9999 0 s or Activation delay
stitches
or °
t 11 67 0 2 0 - Type of switch-off delay of func-
tion module 1 (X1.15)
0 = Time
1 = Stitches
2 = Bracket

DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022 23

 Parameter list

E C P Min Max Preset Unit Description

value
t 11 68 0 9999 0 s or Switch-off delay
stitches
or °
t 11 69 1 3 1 - Condition of function module 3
(X1.15) before thread cutting
1 = Unchanged;
2 = Deactivated;
3 = Activated
t 11 90 0 999 100 ms Activation time of output FF3 in
period t1
t 11 91 5 100 100 % Duty cycle in period t1
t 11 92 0,0 600,0 0,0 s Activation time of output FF3 in
period t2 (if 0, output FF3 remains
continuously switched on)
t 11 93 5 100 100 % Duty cycle in period t2
t 11 94 0 1 0 - Increase in Umag when output FF3
is activated
0 = No;
1= Yes
Reversal
t 12 00 0 1 1 - Reversal
0 = No;
1= Yes
t 12 01 10 350 45 ° Reversal angle
t 12 02 10 255 40 ms Waiting time until reversal
t 12 03 0 1 0 - Reverse before seam beginning
0 = No;
1= Yes
t 12 04 10 180 10 ° Reversal angle at seam begin-
ning
Needle cooling/fan
t 13 00 0 1 1 - Needle cooling mode
0 = Normal needle cooling;
1 = Speed-dependent needle
cooling
t 13 01 0,0 9,999 0,500 s Switch-off delay of needle cooling
t 13 02 100 9999 500 rpm Speed for switching on needle
cooling
t 13 03 0 1 0 - Needle cooling during sewing
foot lift
0 = No;
1 = Yes
t 13 04 0 1 0 - Needle cooling during pedal in
forward Position ½
0 = No
1 = Yes

24 DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022

Parameter list

E C P Min Max Preset Unit Description

value
Carrier roller/puller/seam middle guide
t 14 00 0 3 3 - Mode for automatic raising of the
carrier roller
0 = Do not raise;
1 = With sewing foot lift;
2 = During bartacking;
3 = During bartacking and when
sewing foot is lifted
t 14 01 0 1 0 - Raise carrier roller when stroke
adjustment switched on
0 = No;
1= Yes
t 14 02 0 1 0 - Stitch count delay after sewing
foot lift (t 14 03)
0 = No;
1= Yes
t 14 03 0 255 0 Stitches Number of stitches until carrier
roller is lowered
t 14 04 0 1 1 - Encoder Top
0 = No;
1 = Yes
t 14 05 0 1 1 - Encoder Bottom
0 = No;
1 = Yes
t 14 10 0 2 0 - Number of active pullers
(Output X1.26 is configured for
pressure switch-off)
0 = No puller;
1 = Puller from above;
2 = Puller from above and below
t 14 11 0 1 0 - Puller feeding type
0 = Continual;
1 = Intermittent
t 14 12 0 359 30 ° Start feed angle
t 14 13 0 359 150 ° End feed angle
t 14 14 0 2 0 - Puller without pressure (output
X1.26 is used for this)
0 = With pressure;
1 = During quick stroke adjust-
ment without pressure;
2 = Continuously without pres-
sure
t 14 15 0 1 0 - Puller is powered off when sew-
ing stops
0 = No;
1= Yes

DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022 25

 Parameter list

E C P Min Max Preset Unit Description

value
t 14 16 0 1 0 - Puller active even if no carrier
roller is active
0 = No;
1= Yes
t 14 17 10 150 90 mm Maximum feed length
t 14 20 0,1 65,00 1,00 - Transmission ratio, top puller
t 14 21 1 200 50 - Material correction, top puller,
when feed length is 5 mm
t 14 22 0,1 5,00 3,50 A Set current, top puller
t 14 23 0,1 3,00 1,00 A No-damage current, top puller
t 14 24 1 9999 50 mm Diameter of top carrier roller
t 14 25 0 1 0 - Direction of rotation
0 = Right;
1 = Left
t 14 26 -10,0 10,0 1,0 mm Feed length during short stitch,
top puller
t 14 30 0,1 65,00 1,00 - Transmission ratio of bottom
puller
t 14 31 1 200 50 - Material correction, bottom puller,
when feed length is 5 mm
t 14 32 0,1 5,00 3,50 A Set current, bottom puller
t 14 33 0,1 3,00 1,00 A No-damage current, bottom
puller
t 14 34 1 9999 49 mm Diameter of bottom carrier roller
t 14 35 0 1 0 - Direction of rotation
0 = Right;
1 = Left
t 14 36 -10,0 10,0 1,0 mm Feed length during short stitch,
bottom puller

26 DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022

Parameter list

E C P Min Max Preset Unit Description

value
Edge cutter
t 15 00 0 7 0 - Mode for automatic raising of the
edge cutter
0 = Do not raise;
1 = With sewing foot lift;
2 = After cutting or after stitch
counting
(t 15 04);
3 = After cutting or after stitch
counting and when sewing
foot is lifted;
4 = During bartacking;
5 = During bartacking and when
sewing foot is lifted;
6 = After cutting or after stitch
counting and during bartack-
ing;
7 = After cutting or after stitch
counting, during bartacking
and when sewing foot is lift-
ed
t 15 03 0 255 0 Stitches Number of stitches until edge
cutter is lowered
t 15 04 0 255 0 Stitches Number of stitches until edge
cutter is lifted (t 15 00 = 2 or 3)
t 15 05 0 1 0 - Deactivate edge cutter when
sewing foot is lifted
0 = No;
1= Yes
t 15 10 0 1 0 - Electric edge cutter
0 = No;
1= Yes
t 15 11 0 1 0 - Electric edge cutter when sewing
stops
0 = No;
1= Yes
t 15 12 0 100 50 % Minimum PWM for edge cutter
t 15 13 0 100 95 % Maximum PWM for edge cutter
t 15 14 0 9999 1500 rpm Maximum speed at which maxi-
mum PWM is to be reached
t 15 15 0,0 2,55 0,0 s Delay for switching off the edge
cutter motor
t 15 16 0,0 9,999 0,0 ms Delay between footlifting and
lifting/lowering the edge cutter
Light barrier
t 16 00 50 9999 1000 rpm Speed for light barrier equalizing
stitches

DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022 27

 Parameter list

E C P Min Max Preset Unit Description

value
t 16 01 1 3 3 - Light barrier mode
1 = Seam beginning detection;
2 = Seam end detection;
3 = Seam beginning & seam end
detection
t 16 02 0 1 0 - Mode for seam beginning
0 = Release via light barrier;
1 = Start via front pedal and light
barrier
t 16 03 0 1 0 - Knitted garment filter
0 = Off;
1 = On
t 16 04 0 1 0 - Light barrier detection
0 = Bright;
1 = Dark
t 16 05 0 1 0 - Light barrier automatic mode
(only if t 16 01 = 2 or 3)
0 = Off;
1 = On
t 16 06 0 9999 0 ms Time material needs to be de-
tected before machine start
t 16 07 0 1 0 - Foot lowering only when material
is detected. (only with t 16 01 = 1
or 3 and manual sewing)
0 = Off;
1 = On
t 16 08 0 9999 0 ms Delay between start and foot
lowering (only with t 16 07 = 1)
t 16 09 0 9999 0 ms Delay between foot lowering and
sew start (only with t 16 07 = 1)
Electronic handwheel
t 17 00 0 1 1 - Electronic handwheel
0 = No;
1 = Yes (t 51 32 and t 51 33 = 0)
t 17 01 1 255 15 - Step width for electronic hand-
wheel
t 17 02 0 1 0 - Direction of rotation of electronic
handwheel
0 = Right;
1 = Left
Stacker
t 18 00 0 1 0 - Stacker
0 = Off;
1 = On
t 18 01 0,0 2,55 0,10 s Activation delay stacker
t 18 02 0,0 2,55 0,10 s Time when stacker starts clamp-
ing
t 18 03 0,0 2,55 0,10 s Duty cycle of the stacker

28 DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022

Parameter list

E C P Min Max Preset Unit Description

value
Zigzag
t 19 00 0 359 112 ° Switch position for zigzag
t 19 01 4 6 6 Stitches Number of stitches for zigzag
Thread wiper
t 20 00 0 1 0 - Thread wiper
0 = Off;
1 = On
t 20 01 10 255 100 ms Switch-on period for thread wiper
Step cutting/contour guide
t 21 00 0,0 2,55 0,50 s Delay after switching off edge
cutter for step cutting
t 21 01 0,0 2,55 0,50 s Delay for extension of stepped
cylinder
t 21 02 0,0 2,55 0,50 s Duration of impulse blowing
during extension of stepped
cylinder
t 21 03 0,0 2,55 0,50 s Delay for switching off blowing
when sewing stops
t 21 04 0,0 2,55 0,50 s Delay for switching on edge
cutter after switching step cutting
on/off
Outfeed roller
t 22 00 0 3 0 - Outfeed roller mode
0 = Off;
1 = Seam end;
2 = Seam beginning;
3 = Seam beginning & seam end;
t 22 03 0 255 0 Stitches Number of stitches until outfeed
roller is lowered at seam begin-
ning
t 22 04 0 255 0 Stitches Number of stitches until outfeed
roller is lifted at seam beginning
t 22 05 0,0 99,99 0,50 s Activation delay of the outfeed
roller
t 22 06 0,0 99,99 0,50 s Duty cycle of outfeed roller at
seam end
t 22 07 0,0 20,0 5,0 kHz Speed of outfeed roller at seam
end
Hook lubrication
t 23 00 0 9999 0 Stitches Number of stitches until hook
lubrication is activated
t 23 01 0,0 99,99 0,0 s Duration of hook lubrication
Chain-sucking
t 24 00 0 100 30 Stitches Number of stitches until suction
at the beginning is deactivated
t 24 01 0,0 10,0 0,8 s Duration of the final suction

DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022 29

 Parameter list

E C P Min Max Preset Unit Description

value
Stitch loosening device
t 25 00 0 1 0 - Automatic sewing material thick-
ness detection
0 = Off;
1 = On
t 25 05 0 1 1 - Speed reduction during stitch
loosening
0 = Off;
1 = On
t 25 06 0 1200 800 rpm Level to which speed will be
reduced
t 25 07 1 3 1 - Condition of stitch loosening
function after thread cutting
process
1 = Unchanged;
2 = Deactivated;
3 = Activated
t 25 10 1 255 1 Stitches Number of stitches after automat-
ic switching on, when the stitch
loosening function is forced
t 25 11 0 255 0 Stitches Number of stitches with stitch
forced loosening function, after
which function is deactivated
t 25 12 0 1 0 - Additional to t 25 11 it is possible
to programm/select the number
of stitches with the seamway 2
and 3 button
0 = Off;
1 = On
t 25 15 0 1 0 - Possibility to interchange fabric
thickness threshold for switch
on/off (only with t 25 00 = 1)
Tape Cutter
t 26 00 0 1 0 - Tape Cutter
0 = Off;
1 = On
t 26 01 0,0 2,55 0,80 s Power-up delay tape cutter
t 26 02 0,0 2,55 0,40 s Switch-on duration tape cutter
Fabric thickness sensor
t 27 00 0 1 0 - Fabric thickness sensor
0 = Off;
1 = On
t 27 01 0,0 9,9 0,0 mm Fabric thickness threshold for
switch on
t 27 02 0,0 9,9 0,0 mm Fabric thickness threshold for
switch off
t 27 03 0,0 9,9 0,0 mm Fabric thickness second thresh-
old for switch on

30 DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022

Parameter list

E C P Min Max Preset Unit Description

value
t 27 04 0,0 9,9 0,0 mm Fabric thickness second thresh-
old for switch off
Chain cutter
t 28 00 0 2 0 - Chain cutter mode
0 = Off;
1 = On;
2 = Clamps after cutting
t 28 01 0 255 0 Stitches Power down delay after sew start
(only with t 28 00 = 2)
t 28 02 50 999 50 ms Duty cycle of the chain cutter
(with t 28 00 = 1)
Stitch length switching
t 30 00 0 2 2 - Speed limit if stitch length is long
0 = Off;
1 = Speed limit DB2000;
2 = Speed limit DB3000
t 30 01 0 2 0 - Stitch length during bartacking
0 = Preset stitch length
(Long/Normal);
1 = Normal stitch length;
2 = Long stitch length
t 30 02 0 2 0 - Stitch length after thread cutting
0 = Selected stitch length is
retained;
1 = Normal stitch length;
2 = Long stitch length
Stitch shortening
t 31 00 0 255 0 Stitches Stitch shortening at seam begin-
ning
t 31 01 0 255 0 Stitches Stitch shortening during thread
cutting
Operation lock
t 50 00 0 1 1 - Operation lock
0 = Off;
1 = On
t 50 01 0 1 0 - Method of operation of operation
lock switch
0 = Closed contact (NC);
1 = Open contact (NO)
t 50 02 0 1 1 - Behavior of the motor
0 = Emergency cut-off;
1 = Positioning
Control, other
t 51 00 - - - - Display software version
t 51 01 - - - - Display control serial number

DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022 31

 Parameter list

E C P Min Max Preset Unit Description

value
t 51 02 0 1 0 - Display analog values (see t 51
12) during the sewing process
0 = No;
1= Yes
t 51 04 - - - - Display class and subclass
t 51 05 - - - - Display operating hours
t 51 06 - - - - Display operating stitches
t 51 07 - - - - Display piece counters
t 51 08 0 1 - - M2M
0 = Off;
1 = On
t 51 09 - - - - Enter/display M2M Customer ID
t 51 10 0 5 - - Import data to control
0 = None; 1 = Parameter settings
from DA dongle; 2 = Parameter
settings from backup area;
3 = Seam paths from DA dongle;
4 = Master reset;
5 = Reset seam paths
t 51 11 0 3 - - Saving of parameters
0 = None;
1 = Parameter settings onto DA
dongle;
2 = Parameter settings into back-
up area;
3 = Seam paths to the DA dongle
t 51 12 - - - - Hardware test
Inputs and outputs in bold are
only present in the DAC classic.
1. Analog
Um: Mains voltage in V
U24: power supply outputs in V
Imo: current of 24 V power sup-
ply
PAn: analog value of pedal
Nre: X1.4 analog input
Ian: X1.1 analog input
Pst: digitized pedal position
I2T: I²T of the motor (caution:
pedal and motor are active!)
2. Input
X1.5: Manual Backtack
X1.6: Nedle up/down
X1.7: Additional thread tension
(module 2)
X1.8: Switch stitch length (mod-
ule 1)

32 DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022

Parameter list

E C P Min Max Preset Unit Description

value
X1.9: Input function module 3
(module 3)
X1.10: Limitation DB3000
X1.11: Machine run blockage
X1.12: Bobbin thread monitor
X1.13: Light barrier
X1.14: Backtack suppres-
sion/recall
X2.1: High lift for walking foot
(not stored)
X2.2: High lift for walking foot
(stored)
X2.3: No Function
X2.4: No Function
X2.6: No Function
X2.7: No Function
3. Output
X1.15: Output function module 3
(module 3)
X1.17: No Function
X1.18: Thread clamp
X1.20: Additional thread tension
(module 2)
X1.21: No Function
X1.22: LED function module 3
(module 3)
X1.23: LED bobbin thread moni-
tor left
X1.24: LED Backtack suppres-
sion/recall
X1.25: LED bobbin thread moni-
tor right
X1.26: No Function
X1.27: No Function
X1.28: Needle cooling
X1.29: LED switch stitch length
(module 1)
X1.30: Switch stitch length (mod-
ule 1)
X1.31: LED additional thread
tension (module 2)
X1.32: High lift for walking foot
X1.34: Backtacking
X1.35: Sewing foot lifting
X1.36: Thread tension
X1.37: Thread trimmer
4. Flash
t 51 13 - - - - Display last 10 error messages
1 = most recent error
10 = first error

DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022 33

 Parameter list

E C P Min Max Preset Unit Description

value
t 51 14 0 2 - - Reset maintenance counter
0 = No;
1= Yes
t 51 15 0 1 - - Automatic reset of M2M counters
after power-on
0 = No;
1= Yes
t 51 16 0 1 - - Reset of M2M counters
0 = No;
1= Yes
t 51 17 0 9999 - - Password for the technician level.
Password Value 0 disables the
password query.
t 51 20 0 60 3 - Set input function for bartack
input (machine connector Pin 5)
0 = No function;
1 = Threader;
2 = Bartack suppres-
sion/activation;
3 = Manual bartack;
4 = Half stitch;
5 = Whole stitch;
6 = Point position;
7 = Reversal;
8 = Function module 1 input
(see t 11 00);
9 = Function module 2 input
(see t 11 30);
10 = Function module 3 input
(see t 11 60);
11 = Needle high;
12 = Ornamental-stitch bartack;
13 = Needle cooling;
14 = Thread wiper;
15 = Normal stitch length during
bartacking;
16 = Operation lock when contact
open (NO);
17 = Operation lock when contact
closed (NC);
18 = Quick stroke adjustment
(not stored);
19 = Quick stroke adjustment
(stored);
20 = Speed limit DB2000;
21 = Speed limit DB3000;
22 = Light barrier;
23 = Puller feeding type (continu-
al/intermittent);
24 = Sewing foot lift with pedal in

34 DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022

Parameter list

E C P Min Max Preset Unit Description

value
position 0;
25 = Release for new seam;
26 = Manual bartack stored;
27 = Move to zigzag position;
28 = Zigzag synchronization;
29 = Stacker on/off;
30 = Manual stacking
31 = Function module 1 input on
(see t 11 00);
32 = Function module 1 input off
(see t 11 00);
33 = Function module 2 input on
(see t 11 30);
34 = Function module 2 input off
(see t 11 30);
35 = Function module 3 input on
(see t 11 60);
36 = Function module 3 input off
(see t 11 60);
37 = Service Call (only with
M2M);
38 = Stitch loosening;
39 = Fullness top;
40 = Fullness bottom;
41 = Reverse at seam beginning;
42 = Sewing foot lift after thread
cutter;
43 = Manual sewing
44 = Seam end manu-
al/automatic sewing;
45 = Automatic sewing;
46 = Tape cutter;
47 = Manual tape cutter;
48 = Shoulder seam 3827;
49 = Reset shoulder seam 3827;
50 = Fullness 3827;
51 = No seam end start;
52 = Stitch loosening automatic;
53 = Stitch loosening on/off;
54 = Operation lock on/off;
55 = Fast scissors (PAFF);
56 = Electronic handwheel for-
ward;
57 = Electronic handwheel back-
wards;
58 = Chain cut/suction (Pfaff);
59 = Threadmonitor top;
60 = Threadmonitor bottom

DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022 35

 Parameter list

E C P Min Max Preset Unit Description

value
t 51 21 0 60 2 - Set input function for bartack
toggle input (machine connector
Pin 14)
For function see t 51 20
t 51 22 0 60 4 - Set input function for needle
high/low input (machine connect-
or Pin 6)
For function see t 51 20
t 51 23 0 60 8 - Set input function for input FF1
(machine connector Pin 8)
For function see t 51 20
t 51 24 0 60 9 - Set input function for input FF2
(machine connector Pin 7)
For function see t 51 20
t 51 25 0 60 13 - Set input function for input FF3
(machine connector Pin 9)
For function see t 51 20
t 51 26 0 60 21 - Set input function for input (ma-
chine connector Pin 10)
For function see t 51 20
t 51 27 0 60 0 - Set input function for light barrier
input (machine connector Pin 13)
For function see t 51 20
t 51 28 0 60 18 - Set input function IN_EXT1
(additional input interface Pin 1)
For function see t 51 20
t 51 29 0 60 19 - Set input function IN_EXT2
(additional input interface Pin 2)
For function see t 51 20
t 51 30 0 60 0 - Set input function IN_EXT3
(additional input interface Pin 3)
For function see t 51 20
t 51 31 0 60 6 - Set input function IN_EXT4
(additional input interface Pin 4)
For function see t 51 20
t 51 32 0 60 0 - Set input function IN_EXT5
(additional input interface Pin 6)
For function see t 51 20
t 51 33 0 60 0 - Set input function IN_EXT6
(additional input interface Pin 7)
For function see t 51 20

36 DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022

Parameter list

E C P Min Max Preset Unit Description

value
t 51 50 0 42 1 - Set output function for output
(machine connector Pin 18)
0 = No function;
1 = Thread clamp;
2 = Locking;
3 = Sewing foot lift;
4 = Thread tension;
5 = Auxiliary thread tension;
6 = Second stitch length;
7 = Carrier roller;
8 = Edge stop;
9 = Edge cutter;
10 = Fullness with DB3000;
11 = Fullness without DB3000;
12 = Step cutting;
13 = Contour guide;
14 = Stacker;
15 = Thread cutter;
16 = Quick stroke adjustment;
17 = Needle cooling;
18 = Stitch shortening;
19 = Pulse step cutting;
20 = Open step cutting;
21 = Thread clamp NSB;
22 = Thread puller NSB;
23 = Carrier roller pressure;
24 = Sewing foot pressure;
25 = Ready for sewing start;
26 = Pos. 1;
27 = Pos. 2;
28 = Motor operation;
29 = In the seam;
30 = Outfeed roller;
31 = Transport unit;
32 = Hook lubrication;
33 = Thread wiper;
34 = Suction NSB;
35 = Tape cutter;
36 = Edge cutter off;
37 = Stitch loosening;
38 = Fullness top;
39 = Fullness bottom;
40 = Chain cutter;
41 = Cleaning of SSD sensor;
42 = Pos. 3
t 51 51 0 42 27 - Set output function for output
(machine connector Pin 21),
For function see t 51 50

DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022 37

 Parameter list

E C P Min Max Preset Unit Description

value
t 51 52 0 42 0 - Set output function for output
(machine connector Pin 22),
For function see t 51 50
t 51 53 0 42 26 - Set output function for output
(machine connector Pin 26),
For function see t 51 50
t 51 54 0 42 18 - Set output function for output
(machine connector Pin 27),
For function see t 51 50
t 51 55 0 42 17 - Set output function for output
(machine connector Pin 28),
For function see t 51 50
t 51 56 0 42 16 - Set output function for output
(machine connector Pin 32),
For function see t 51 50
t 51 70 0 9999 0 x t5171 Reset value of maintenance
counter II (counter is deactivated
at 0)
t 51 71 1 255 1 x 1000St Factor of maintenance counter II
t 51 72 1 255 1 x t5171 Error message repeated
t 51 73 0 99 1 - Number of error message re-
peats
OP1000
t 52 00 0 9 4 - Display contrast of OP1000
t 52 01 0 1 1 - Button tones
0 = Off;
1 = On
t 52 20 0 60 1 - Set input function for F button of
OP1000
0 = No function;
1 = Threader;
2 = Bartack suppres-
sion/activation;
3 = Manual bartack;
4 = Half stitch;
5 = Whole stitch;
6 = Point position;
7 = Reversal;
8 = Function module 1 input
(see t 11 00);
9 = Function module 2 input
(see t 11 30);
10 = Function module 3 input
(see t 11 60);
11 = Needle high;
12 = Ornamental-stitch bartack;
13 = Needle cooling;
14 = Thread wiper;

38 DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022

Parameter list

E C P Min Max Preset Unit Description

value
15 = Normal stitch length during
bartacking;
16 = Operation lock when contact
open (NO);
17 = Operation lock when contact
closed (NC);
18 = Quick stroke adjustment
(not stored);
19 = Quick stroke adjustment
(stored);
20 = Speed limit DB2000;
21 = Speed limit DB3000;
22 = Light barrier;
23 = Puller feeding type (continu-
al/intermittent);
24 = Sewing foot lift with pedal in
position 0;
25 = Release for new seam;
26 = Manual bartack stored;
27 = Move to zigzag position;
28 = Zigzag synchronization;
29 = Stacker on/off;
30 = Manual stacking
31 = Function module 1 input on
(see t 11 00);
32 = Function module 1 input off
(see t 11 00);
33 = Function module 2 input on
(see t 11 30);
34 = Function module 2 input off
(see t 11 30);
35 = Function module 3 input on
(see t 11 60);
36 = Function module 3 input off
(see t 11 60);
37 = Service Call (only with
M2M);
38 = Stitch loosening;
39 = Fullness top;
40 = Fullness bottom;
41 = Reverse at seam beginning;
42 = Sewing foot lift after thread
cutter;
43 = Manual sewing
44 = Seam end manu-
al/automatic sewing;
45 = Automatic sewing;
46 = Tape cutter on/off;
47 = Manual cutting tape cutter;
48 = Shoulder seam 3827;

DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022 39

 Parameter list

E C P Min Max Preset Unit Description

value
49 = Reset shoulder seam 3827;
50 = Fullness 3827;
51 = No seam end start;
52 = Stitch loosening automatic;
53 = Stitch loosening on/off;
54 = Operation lock on/off;
55 = Fast scissors (PAFF);
56 = Electronic handwheel for-
ward;
57 = Electronic handwheel back-
wards;
58 = Chain cut/suction (Pfaff);
59 = Threadmonitor top;
60 = Threadmonitor bottom
t 52 40 0 1 0 - Button lock for start bartack
buttons
0 = Off;
1 = On
t 52 41 0 1 0 - Button lock for end bartack but-
tons
0 = Off;
1 = On
t 52 42 0 1 0 - Button lock for thread buttons
0 = Off;
1 = On
t 52 43 0 1 0 - Button lock for button group
seam program
0 = Off;
1 = On
t 52 44 0 1 0 - Button lock for button group
programming
0 = Off;
1 = On
t 52 45 0 1 0 - Button lock for thread clamp
button
0 = Off;
1 = On

1.3 Developer level

E C P Min Max Preset Unit Description
value
Bartack
d 00 01 0 359 15 ° Mechanical switch-over angle for
bartack
Thread cutter (FA)
d 02 00 10 359 100 - Angle at which thread cutting
speed is to be reached before
magnets are switched on

40 DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022

Parameter list

E C P Min Max Preset Unit Description

value
d 02 01 0 1 0 - Chainstitch mode
0 = No;
1= Yes
Seam paths
d 07 00 150 9999 1500 rpm Speed limit for seam paths
d 07 01 1 20 6 Stitches Number of stitches for seam path
speed limit
Motor
d 08 00 1 9999 1000 rpm Maximum motor speed
d 08 01 1 100 20 rpm/ms Maximum acceleration or decel-
eration
d 08 02 0 50 20 Kgcm² Machine inertia
d 08 04 0 255 0 Inc Extension of deceleration ramp
d 08 05 0 1 0 - Acceleration and deceleration
ramp halved when I²t increases
to over 70 %
0 = No;
1= Yes
d 08 10 0,1 100,0 3,1 Ohm Stator resistance
d 08 11 1 200 11 mH Stator inductance
d 08 12 0,1 200,0 67,5 V/1000 EMF
rpm
d 08 13 0,1 15,00 11,00 A Maximum stator current
d 08 14 1 10 3 - Number of pole pairs
d 08 20 0 255 30 - Kpn factor of PID speed controller
d 08 21 0 255 33 - Kin factor of PID speed controller
d 08 22 0 255 0 - Kdn factor of PID speed controller
d 08 23 0 255 12 - Feed-forward of speed control in
deceleration process
d 08 30 0 255 12 - Kps factor of PID distance control-
ler
d 08 31 0 255 3 - KIs factor of PID distance control-
ler
d 08 32 0 255 0 - Kds factor of PID distance control-
ler
d 08 40 0 255 52 - Kpx factor of PID position control-
ler
d 08 41 0 255 52 - Kdx factor of PID position control-
ler
d 08 42 0 255 16 Inc Increments for activation of PID
position controller
d 08 43 0 1000 0 2.857° Angle for positioning

DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022 41

 Parameter list

E C P Min Max Preset Unit Description

value
d 08 44 0 1000 16 Inc Increments for duration of activa-
tion of positioning speed
d 08 45 10 100 50 rpm Increase in speed for position
controller during thread cutting
d 08 46 0 200 0 Inc Increase increments for the
position controller during thread
cutting
d 08 51 0 1 0 - Continuous operation
0 = No;
1= Yes
d 08 52 0,0 99,99 5,00 s Motor on duration
d 08 53 0,0 99,99 5,00 s Motor off duration
d 08 54 1 9999 900 s Duration of continuous operation
d 08 55 0 2000 180 rpm Speed for reference run
Thread tension
d 09 01 5 100 100 % Duty cycle for threader
Top puller
d 14 00 0,1 20,00 6,00 kHz Maximum frequency
d 14 01 1 500 200 rpm/ms Acceleration ramp
d 14 02 1 500 200 rpm/ms Deceleration ramp
d 14 03 1 9000 2000 Hz Start frequency
d 14 04 1 9000 2000 Hz Stop frequency
d 14 05 1 1000 500 Lines Encoder lines
d 14 06 1 9000 2000 Steps Microsteps per turn
d 14 10 0,1 9,000 1,100 Ohm Stator resistance
d 14 11 0,1 9,000 2,200 mH Stator inductance
d 14 12 0 1000 0 - EMF factor
d 14 13 0,1 10,00 3,50 A Maximum stator current (regulat-
ed)
d 14 14 1 100 50 - Number of pole pairs
d 14 15 0,1 10,00 2,00 A Maximum no-damage current
(regulated)
d 14 16 0,1 10,00 3,50 A Maximum stator current (con-
trolled)
d 14 17 0,1 10,00 2,00 A Maximum no-damage current
(controlled)
d 14 20 0 9999 0 - Kpn factor of PID speed controller
d 14 21 0 9999 0 - Kin factor of PID speed controller
d 14 22 0 9999 0 - Kdn factor of PID speed controller

42 DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022

Parameter list

E C P Min Max Preset Unit Description

value
d 14 30 0 9999 1500 - Kps factor of PID distance control-
ler
d 14 31 0 9999 50 - KIs factor of PID distance control-
ler
d 14 32 0 9999 0 - Kds factor of PID distance control-
ler
d 14 40 0 9999 1500 - Kpx factor of PID position control-
ler
d 14 41 0 9999 0 - KIx factor of PID position control-
ler
d 14 42 0 9999 100 - Kdx factor of PID position control-
ler
Bottom puller
d 14 50 0,1 20,00 6,00 kHz Maximum frequency
d 14 51 1 500 200 rpm/ms Acceleration ramp
d 14 52 1 500 200 rpm/ms Deceleration ramp
d 14 53 1 9000 2000 Hz Start frequency
d 14 54 1 9000 2000 Hz Stop frequency
d 14 55 1 1000 500 Lines Encoder lines
d 14 56 1 9000 2000 Steps Microsteps per turn
d 14 60 0,1 9,000 1,100 Ohm Stator resistance
d 14 61 0,1 9,000 2,200 mH Stator inductance
d 14 62 0 1000 0 - EMF factor
d 14 63 0,1 10,00 3,50 A Maximum stator current
d 14 64 1 100 50 - Number of pole pairs
d 14 65 0,1 10,00 2,00 A Maximum no-damage current
d 14 66 0,1 10,00 3,50 A Maximum stator current (con-
trolled)
d 14 67 0,1 10,00 2,00 A Maximum no-damage current
(controlled)
d 14 70 0 9999 0 - Kpn factor of PID speed controller
d 14 71 0 9999 0 - Kin factor of PID speed controller
d 14 72 0 9999 0 - Kdn factor of PID speed controller
d 14 80 0 9999 1500 - Kps factor of PID distance control-
ler
d 14 81 0 9999 50 - KIs factor of PID distance control-
ler
d 14 82 0 9999 0 - Kds factor of PID distance control-
ler
d 14 90 0 9999 1500 - Kpx factor of PID position control-
ler

DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022 43

 Parameter list

E C P Min Max Preset Unit Description

value
d 14 91 0 9999 0 - KIx factor of PID position control-
ler
d 14 92 0 9999 100 - Kdx factor of PID position control-
ler
Control, other
d 51 00 1 255 40 ms Time duration for raising Umag to
33 V
d 51 01 1 255 5 ms Duration for DeEnergizer process
d 51 02 0,1 16,00 16,00 kHz Set PWM frequency
d 51 03 - - - - Display machine serial number
d 51 04 - - - - Display production date
d 51 10 0 9999 8000 x d5111 Reset value of maintenance
counter (counter is deactivated at
0)
d 51 11 1 255 1 x Factor of maintenance counter
10000St
d 51 12 1 255 200 x d5111 Error message repeated
d 51 13 1 99 1 - Number of error message re-
peats

44 DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022

Parameter list

Parametersätze für die Klasse 969

Parametersatz

2
Für Un-

969-100080-2
terklassen
969-190180

969-190382

E K P Preset Preset Preset

t 08 00 1000 1000 1200
t 08 03 10 10 15
t 08 04 10 10 5
t 08 07 0,7 0,7 1,5
t 08 08 30 30 20
t 08 12 115 115 128
t 08 19 359 442 259
d 08 00 1000 1250 1200
d 08 01 20 20 25
d 08 10 3,1 3,1 2,0
d 08 11 11 11 5
d 08 12 67,5 67,5 39,8
d 08 14 3 3 2
d 08 20 30 30 24
d 08 21 33 33 24
d 08 23 12 12 24
d 08 30 12 12 0
d 08 31 3 3 0
d 08 40 52 52 34
d 08 41 52 52 34
d 08 42 16 16 18
d 08 44 16 16 0

DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022 45

 Parameter list

46 DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022

Parameter list

2 Error, warning and information messages

Code Type Possible cause Remedial action

1000 Error Sewing motor encoder plug - Connect encoder cable to the control,
(Sub-D, 9-pin) not connected use correct connection
1001 Error Sewing motor error: - Check connection and plug in, if nec-
Sewing motor plug (AMP) not essary
connected - Test sewing motor phases (R= 2.8 ,
high impedance to PE)
- Replace the encoder
- Replace the sewing motor
- Replace the control
1002 Error Sewing motor insulation error - Check motor phase and PE for low-
impedance connection
- Replace the encoder
- Replace the sewing motor
1004 Error Sewing motor error: - Replace the encoder
Incorrect sewing motor direction - Check plug assignment and change, if
of rotation necessary
- Check wiring in machine distributor and
change it, if necessary
- Test motor phases and check for
correct value
1005 Error Motor blocked - Eliminate stiff movement in the ma-
chine
- Replace the encoder
- Replace the motor
1006 Error Maximum speed exceeded - Replace the encoder
- Perform reset
- Check class (t 51 04)
1007 Error Error in the reference run - Replace the encoder
- Eliminate stiff movement in the ma-
chine
1008 Error Encoder error - Replace the encoder

1010 Error External synchronizer plug Connect cable of external synchronizer

(Sub-D, 9-pin) not connected to control, use correct connection (Sync)
- Only required for machines with trans-
mission!
1011 Error Encoder Z pulse missing - Switch off the control. Turn handwheel
and switch on the control again
- If error is not corrected, check encoder
1012 Error Synchronizer fault - Replace the synchronizer

DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022 47

 Parameter list

Code Type Possible cause Remedial action

1052 Error Sewing motor overcurrent, - Check selection of class

internal current increase >25 A - Replace the control
- Replace the sewing motor
- Replace the encoder
1053 Error Sewing motor overvoltage - Check selection of class
- Replace the control
1054 Error Internal short circuit - Replace the control

1055 Error Sewing motor overload - Eliminate stiff movement in the ma-
chine
- Replace the encoder
- Replace the sewing motor
1203 Information Position not reached (during - Check and, if necessary, change con-
thread cutting, reversal, etc.) troller settings.
Mechanical changes to the machine.
(e. g. thread cutting setting, belt tension,
etc.)
- Check position (thread lever at top
dead center)
2020 Information DACextension box not respond- - Check connection cables
ing - Check LEDs of DACextension box
- Software update
2021 Information Sewing motor encoder plug - Connect encoder cable to DACexten-
(Sub-D, 9-pin) not connected to sion box using the correct connection
DACextension box
2101 Information DA stepper card 1 reference run - Check reference sensor
timeout
2103 Information DA stepper card 1 step losses - Check for stiff movement

2106 Information DA stepper card 1 speed over- -

run
2120 Information DA stepper card 1 not respond- - Check connection cables
ing - Check LEDs of DACextension box
- Software update
2121 Information DA stepper card 1 encoder plug - Connect encoder cable to the control,
(Sub-D, 9-pin) not connected use correct connection
2122 Information DA stepper card 1 flywheel - Check connection cables
position not found - Check stepper motor 1 for stiff move-
ment
2155 Information DA stepper card 1 overload - Check for stiff movement

2201 Information DA stepper card 2 reference run - Check reference sensor

timeout
2203 Information DA stepper card 2 step losses - Check for stiff movement

48 DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022

Parameter list

Code Type Possible cause Remedial action

2206 Information DA stepper card 2 speed over- -

run
2220 Information DA stepper card 2 not respond- - Check connection cables
ing - Check LEDs of DACextension box
- Software update
2221 Information DA stepper card 2 encoder plug - Connect encoder cable to the control,
(Sub-D, 9-pin) not connected use correct connection
2222 Information DA stepper card 2 flywheel - Check connection cables
position not found - Check stepper motor 2 for stiff move-
ment
2255 Error DA stepper card 2 overload - Check for stiff movement

3100 Error AC-RDY timeout, intermediate - Check the mains voltage

circuit voltage did not reach the - If the mains voltage is OK, replace the
defined threshold in the speci- control
fied time
3101 Error High voltage fault, mains volt- - Check mains voltage, if nominal volt-
age, longer duration >290 V age is continuously exceeded, stabilize it
or use a generator
3102 Error Low voltage failure - Check the mains voltage
(2nd threshold) (mains voltage < - Stabilize mains voltage
150 V AC) - Use generator
3103 Information Low voltage warning - Check the mains voltage
(1st threshold) (mains voltage < - Stabilize mains voltage
180 V AC) - Use generator

3104 Warning Pedal is not in position 0 When switching the control on, take your
foot off the pedal
3105 Error U24 V short circuit - Disconnect 37-pin plug; if error per-
sists, replace control
- Test inputs/outputs for 24 V short
circuit
3106 Error U24 V (I²T) overload - One or more magnets defective

3107 Error Pedal not connected - Connect analog pedal

3108 Information Speed limited due to insufficient - Check the mains voltage
mains voltage
3109 Warning Operation lock - Check tilt sensor on machine

3150 Information Maintenance necessary - For information on lubricating the

machine, see the service instructions for
the machine

DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022 49

 Parameter list

Code Type Possible cause Remedial action

3151 Warning Maintenance necessary (opera- - Service is urgently required, see ser-
tion cannot continue unless vice instructions for the machine
parameter
t 51 14 is reset, see the operat-
ing instructions of the machine)
3152 Information Maintenance counter II expired -

3153 Warning Maintenance counter II expired -

(operation cannot continue
unless counter is reset with
parameter t 51 14 = 2)
3155 Information No release for sewing process - Parameter t 51 20 – t 51 33 = 25
- Input signal for sewing process release
required
3160 Information Stitch loosening device - Stitch loosening cannot be performed

3170 Information Quality issues of the fabric - Check the positioning of the fabric
thickness signal thickness sensor
3210 Information Topthread torn -

3211 Information Bottomthread torn -

3215 Information Bobbin stitch counter (info value - Change bobbin, set counter value -
0 reached) press counter reset button
3216 Information Remaining thread monitor left - Change left bobbin

3217 Information Remaining thread monitor right - Change right bobbin

3218 Information Remaining thread monitor left - Change left and right bobbin
and right
3219 Information Mode for Bobbing-Thread- - Thread cutting
Winding is active
3223 Information Skip stitch detected -

3224 Information Bobbin failed to rotate -

3325 Information SSD sensor is dirty -

6353 Error Internal EEprom communication - Switch off the control, wait until the
error LEDs are off and then switch on again
6354 Error External EEprom communica- - Switch off the control, wait until the
tion error LEDs are off, check connection for
machine ID, switch on control again
6357 Error Short circuit EEprom - Switch off the control, wait until the
LEDs are off, check connection for
machine ID, switch on control again
- replace control
- replace Masch-ID

50 DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022

Parameter list

Code Type Possible cause Remedial action

6360 Information No valid data on external - Software update

EEprom (internal data structures
are not compatible with the
external data storage device)
6361 Information No external EEprom connected - Connect machine ID

6362 Information No valid data on internal - Check machine ID connection

EEprom (internal data structures - Switch off the control, wait until the
are not compatible with the LEDs are off and then switch on again
external data storage device) - Software update

6363 Information No valid data on internal and - Check machine ID connection

external EEprom - Switch off the control, wait until the
(Software version is not compat- LEDs are off and then switch on again
ible with the internal data stor- - Software update
age device, emergency operat-
ing features only)
6364 Information No valid data on internal - Check machine ID connection
EEprom and external EEprom - Switch off the control, wait until the
not connected LEDs are off and then switch on again
(the internal data structures are - Software update
not compatible with the external
data storage device, emergency
operating features only)
6365 Information Internal EEprom defective - Replace the control

6366 Information Internal EEprom defective and - Replace the control

external data not valid
(emergency operating features
only)
7202 Information DACextension box boot error - Check connection cables
- Software update
- Replace DACextension box
7203 Information Checksum error during update - Check connection cables
- Software update
- Replace DACextension box
7212 Information DA stepper card 1 boot error - Check connection cables
- Software update
- Replace DACextension box
7213 Information Checksum error occurred while - Check connection cables
updating DA stepper card 2 - Software update
- Replace DACextension box
7222 Information DA stepper card 2 boot error - Check connection cables
- Software update
- Replace DACextension box

DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022 51

 Parameter list

Code Type Possible cause Remedial action

7223 Information Checksum error occurred while - Check connection cables

updating DA stepper card 2 - Software update
- Replace DACextension box
7231 Information Bobbin control is not connected - Check connection cables
- Software update
7232 Information Bootloader failure bobbin control - Check connection cables
- Software update
7233 Information Checksum error occurred while - Check connection cables
updating bobbin control card - Software update
7241 Information Fabric thickness sensor is not - Check connection cables
connected - Software update
7801 Information Software version error - Software update
(DAC classic only; only the - Replace the control
functions of the DAC basic will
remain available)
7802 Information Software update error - Another software update
(DAC classic only; only the - Replace the control
functions of the DAC basic will
remain available)
7803 Information Communication error - Restart of the control
(DAC classic only; only the - Software update
functions of the DAC basic will - Replace the control
remain available)
8401 Error Watchdog - Software update
- Machine ID reset
- Replace the control
8402 Error Internal error - Software update
- Machine ID reset
–
- Replace the control
8405

8406 Error Checksum error - Software update

- Replace the control
8501 Error Software protection - the DA tool must always be used for
software updates

52 DAC basic/classic Parameter list class 969 - version B03.8 - 06-2022

 Subject to design changes – Printed in Germany - © Dürkopp Adler GmbH – Parameter List 0791 969901 - Version B03.8 - 06-2022
DÜRKOPP ADLER GmbH
Potsdamer Str. 190
33719 Bielefeld
Germany
Phone: +49 (0) 521 925 00
Email: service@duerkopp-adler.com
www.duerkopp-adler.com