Project : Farakka Expansion Line 2

Owner : M/s. Ambuja Cements Ltd. (ACL) Kendua, Distt, Murshidabad, West Bengal.
Client :LNV Technology Pvt.Ltd, Egmore, Chennai
Contractor :Technico (India) Private Limited
Subject : BOQ of Fire Protection System for Cement Plant Area
SL.
DESCRIPTION UNIT QTY Remarks
NO
A FIRE PUMP ROOM EQUIPMENT
5.0 Control Panel for Fire pumps.

Fabrication, Supplying, Installation, Testing & Commissioning of electrical control

panel, of cubical construction, floor mounted type, fabricated out of 2mm thick CRCA
sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder
coated of approved shade after 7 tank treatment process, cable alley, inter-
connection, having switchgears and accessories mounting and internal wiring, earth
A terminals, numbering etc. complete in all respects, suitable for operation on 415 V, 3
phase, 50 HZ. AC supply with enclosure protection class IP 42 as required. Provision
shall be made for providing potential free contacts to all pumps starters for
connection to FACP for monitoring the status of the pumps. ( MCC panel for fire
fighting will be located at MCC room which is avilable at Water Treatment Plant. The
distance between fire pump hose and MCC room is approx. 55.0m)

(i) INCOMER (dual input)

(a) 2 Nos 630 Amps. 4 Pole MCCB, 36 KA Thermal Magnetic type with operating
handle mechanism and changeover interlocking etc. and necessary accessories
(b) Voltmeter (0-500 Volts) with selector switch.
(c) Ammeter (0- 700Amps.) with selector switch & CT's etc.
(d) Set of 3 Phase indicating lamp. (e) Set
of AJ.bus bar Amps.

(ii) OUTGOING.
(a) Hydrant Pump 1
400 Amps. 4 Pole MCCB, 25 KA Thermal Magnetic type with operating handle
mechanism and necessary accessories with 300 HP fully automatic star/ delta starter
with over load protection, current sensing type single phase preventor complete with Revised GA Drawing submitted on
all accessories and internal wiring required for automatic operation, selector switch Set 1 01.03.2025. Awaited for
for local/remote, auto/manual/OFFoperation. approval/comments from LNVT.

(b) Hydrant Pump 2

400 Amps. 4 Pole MCCB, 25 KA Thermal Magnetic type with operating handle
mechanism and necessary accessories with 300 HP fully automatic star/ delta starter
with over load protection, current sensing type single phase preventor complete with
all accessories and internal wiring required for automatic operation, selector switch
for local/remote, auto/manual/OFFoperation.
(c) Sprinkler/Spray Pump
400 Amps. 4 Pole MCCB, 25 KA Thermal Magnetic type with operating handle
mechanism and necessary accessories with 300 HP fully automatic star/ delta starter
with over load protection, current sensing type single phase preventor complete with
all accessories and internal wiring required for automatic operation, selector switch
for local/remote, auto/manual/OFFoperation.
(d) Jockey pump 1 for Hydrant
63 Amps. 4 Pole MCCB, 25 KA Thermal Magnetic type with operating handle
mechanism and necessary accessories with 15HP fully automatic DOL starter with
over load protection, current sensing type single phase preventor complete with all
accessories and internal wiring required for automatic operation, selector switch for
local/remote, auto/manual/OFFoperation.
(e) Jockey pump 2 for Sprinkler
63 Amps. 4 Pole MCCB, 25 KA Thermal Magnetic type with operating handle
mechanism and necessary accessories with 15HP fully automatic DOL starter with
over load protection, current sensing type single phase preventor complete with all
accessories and internal wiring required for automatic operation, selector switch for
local/remote, auto/manual/OFFoperation.
7.0 1100 V GRADE POWER / CONTROL CABLES
Supplying, laying, testing & commissioning of FRLS,PVC outer sheateh, steel
armoured, aluminium / copper conductor, 1100v grade power cables with glands
etc.The cables shall be laid in tray / Hume pipe / in trenches/on walls/ floor etc. as Cable Schedule will be submitted within
lot 1
required. For cables laid out door the rate shall include earth excavation providing this week.
brick and sand protection, refilling and compacting the earth.The rate shall excludes
tray & Hume pipes.
8.0 CABLE TRAY
Supplying and fixing of perforated G.I.sheet cable tray with neccessory angle iron
suspension supports, anchor fasteners etc. complete. Maximum height of suspension Under manufacturing. Expect to raise
m 65
shall not exceed 500 mm.Size of the tray shall be suitable for laying the above inspection call within this week.
mentioned cables.
SL.
DESCRIPTION UNIT QTY Remarks
NO
G.I. Earthing strips of 50mm x 6mm thick, strip shall be run on floor / ceiling / walls,
Inspection call raised on 27.02.2025.
9.0 from the equipment to the nearest Earth pit with neccessory accessories as required. m 75
Awaited for MDCC from LNVT.
( Erath pit shall be executed by other agencies).

Supplying, installing, testing and commissioning of G.I Pipes, ERW confirming to IS

1239 Pt - I Heavy grade (Class-C) up to 150mm dia and pipes 200mm dia and above
shall be as per IS: 3589 with malleable specials such as Reducers,Tees, elbows,
10.0 flanges. Including cutting, Welding, fixing in / on walls, ceiling by using suitable
supports etc, complete. The exposed pipes shall be protected by one coat of red
oxide primer or zinc chromate primer and two coats of synthetic enamel paint of fire
red in color shade 536 as per IS 5.

a 300mm nominal dia m 72

Under manufacturing.
b 250mm nominal dia m 18
c 200mm nominal dia m 24
d 150mm nominal dia m 48
e 100mm nominal dia m 12 Delivered to site
f 80mm nominal dia m 18
h 25mm nominal dia m 42
Supplying, installing, testing and commissioning of Cast Iron, flanged Non-return
11.0 valves as per IS:5312 (PN 1.6) ball type with required flanges, nuts, bolts and
gaskets etc. complete.
a 300 mm nominal dia Nos 1
b 200 mm nominal dia Nos 3 Under manufacturing, expect to raise the
c 150 mm nominal dia Nos 1 inspection call mid of March.
d 80 mm nominal dia Nos 2
Supplying, installing and commissioning C.I. flanged Basket type Strainer with SS
12.0
screen, PN-16 rating suitable flanges, nuts, bolts, gaskets etc. complete.
a 250mm dia. Nos. 3 Revised TDS submitted on 03.03.2025.
b 200mm dia. Nos. 1 Awaited for approval/comments from
c 100mm dia. Nos 2 LNVT.

Supply, Erection, Testing and commissioning of Cast iron flanged Sluice valves as per
13.0 IS 14846 and PN 1.6 Rating, for suction & delivery side of the pumps and Non rising
spindle type with flanges, bolts, nuts, washers, gaskets etc.
a 300mm nominal dia Nos 3
b 250mm nominal dia Nos 3
c 200mm nominal dia Nos 4
Delivered to site.
d 150mm nominal dia Nos 6
e 100mm nominal dia Nos 2
f 80mm nominal dia No 4
Supply, Erection, Testing and commissioning of flanged Ductile iron body Gear
14.0 operated butterfly valve with PN-16 operating pressure complte with DI body
conforming to ASTM A536, flanged ANSI 16.5 Class 150, nuts, bolts and gaskets etc.

a) 150mm nominal dia No. 1 MDCC Received. Will be dispatched soon.

Supplying, installing, testing and commissioning of SS Bellow type flexible coupling

15.0
on suction and delivery side of Fire pumps complete with all accessories.
a 250mm nominal dia Nos 3
b 200mm nominal dia Nos 4
Under manufacturing. Expect to raise
c 150mm nominal dia Nos 1
inspection call by the end of March.
d 100mm nominal dia No 2
e 80mm nominal dia No 2
Supplying, installing, testing and commissioning of forged brass Ball valves confirming
16.0
to IS 554 with lever of screwed end type.
a 25 mm nominal dia (for Air Vessel Tank & pressure switch manifold) Nos 6 Delivered to site.
Supply and installation testing and commissioning of standard & differential Pressure
switches of suitable range (0 to 20 bar) for pumpsets complete with necessay Ball Under manufacturing. Expect to raise
17.0 Set 6
valves, Fittings like unions / colors / reducers etc.(Standard type for main pump & inspection call within this week.
Differential type for Jockey Pump)
Supply and installation testing and commissioning of glycerin filled Pressure gauges
of suitable range (0-20 bar), 150 mm diameter dial for pumpsets completes with Under manufacturing. Expect to raise
18.0 Set 8
necessary Ball valves, U shaped SS siphon, Fittings like unions / colors / reducers inspection call within this week.
etc.
Supply, Erection, Testing and commissioning of Flow meter,Electromagnetic type, UL
/ FM approved make completes with carbon steel body ASTM A 106 B/C HRS,
19.0
flanged ANSI 16.5 Class 150, nuts, bolts and gaskets etc. complete. The flow meter
to installed between gate valve and butterfly at rest line header of fire pump.
Under manufacturing. Expect to raise
a) 150 mm nominal dia No 1
inspection call in mid of March.
SL.
DESCRIPTION UNIT QTY Remarks
NO
Supply, fixing, testing and commissioning of air vessel tank shall be fabricated out of
of 300 mm dia MS pipe to 1000 mm long complete with 25mm inlet, 25mm drain,
20.0 25mm dia connection for air release valve including legs, painting with red oxide No 1 Delivered to site.
primer and finished with fire red enamel paint. It shall be inclusive of all relevant
pipes, valves, specials upto pump header and other accessories etc.
Thermal insulation of exhuast pipe for Diesel engine of 150 mm dia M.S pipe with
mineral wool insulation with aluminum sheet. The quoted rate shall include 150 mm Expect to raise inspection call within next
21.0 Mtrs 35
diameter MS pipe heavy grade conforming to IS 1239 Part-1 and mineral wool week.
insulation with aluminum sheeting and Pipe supports also.
Supplying and erecting of Pre fabricated M.S structural steel supports such as angle,
Channel, Plate etc. conforming to relevant IS standards for laying above ground
22.0 Kg 1100 Delivered to site.
Hydrant Pipe. Quoted rate shall inclusive of one coat of primer and one coat of
synthetic enamel paint of approved shade.

Supply, delivery, storing at site, installation, testing & commissioning of Electric hoist,
lift weight capacity is 3.0 T, lift height is 6.0mtr, Running speed is 20m/min, Supply
voltage 415V, 50HZ capacity EOT crane having hoisting motion electrical and CT and
LT motion manual to be operated from floor by hand chain. The lifting motor power is
4.5KW, Rotational speed is 1380r/min and Running motro power is 0.4KW, Rotational
speed is 130r/min.This work also includes manufacture, supply & fixing of MS long MDCC received on 04.03.2025. Will be
23.0 No 1
travel girder with square rail with sole plate and holding down bolts to be fitted on the dispatched within this week.
existing concrete beam for the LT motion and power feeding arrangement along the
longitudinal travel of the crane, GI conductor with supporting brackets. The crane
should be marked with safe working load (SWL) and the purpose for which they are
intended, the down shop conductors should be fully insulated shrouded bas bar type,
including all sundries as per direction of E.I.C.

Automatic OHT level control system with Electrical Actuated Butterfly valve- - Control
Box IP54CB, 230VAC - 5 MINI Level Float Switch
• Automatic OHT Level Control System Consist of Following Items 1) Electrical
Actuated butterfly valve, ON-OFF type, Single Phase 220V AC, Wafer Ends, CI Body Under manufacturing. Expect to raise
24.0 Nos 2
& SS Disc 2) Minifloat - 5 Nos 3) Control Box - 5 level with mini floats, LED Lamps: 5 inspection call in the 3rd week of March.
Level Indications and power supply * Warning below 25% and above overflow levels *
Hooter Acknowledgement Button * Power supply toggle switch * Input 230V Single
Phase power supply * Data Communication Optional at extra cost.

supply and installation of anti-vortex plate with 2D of suction header pipe size to be
fixed inside the fire water tank on suction to prevent the formation of a vortex and Under manufacturing. Expect to raise
25.0 Nos 2
therefore air entrainment into the pump by forcing any emerging vortex to go around a inspection call in this week.
plate and then into the suction pipe. The plate shall be MS and bolted.
B EXTERNAL HYDRANT SYSTEM
Supplying, installing, testing and commissioning of M.S Pipes confirming to IS 1239
Pt - I Heavy grade (Class-C), ERW, above ground pipe with suitable type of
supports (Shall be fabricated by M.S. Channel / Angle, anchor fasteners, bolts, nuts,
clamps, "U" bolt, malleable specials such as Reducers,Tees, elbows, flanges.
Including cutting, Welding, fixing in / on walls, ceiling by using suitable supports etc, .
1.0 The quoted rate shall also include for chasing / chipping walls, making bore holes in
walls whereever required and making them good with filler material. The exposed
pipes shall be protected by one coat of red oxide primer or zinc chromate primer and
two coats of synthetic enamel paint of fire red in color shade 536 as per IS 5. The
fittings shall be butt weld type for 65NB and above & socket weld type for 50NB and
below.
a) 250 mm nominal dia Mtrs 372
b) 200 mm nominal dia Mtrs 1,392
c) 150 mm nominal dia Mtrs 1,194 Delivered to site
d) 100 mm nominal dia Mtrs 198
e) 80 mm nominal dia Mtrs 96
Supply, Installing, testing and commissioning of Heavy class M.S pipe, Class-C
ERW (as per IS-1239 Part-1) laid in under ground (1 Mtrs below ground level). The
quoted rate shall includes necessary specials like long radius bends, tees, including
cutting, welding / flanged joints with necessary washers, nuts, bolts, etc. also include
for providing concrete anchor blocks at all change in direction of pipeline if necessary
and also near each joints. The quoted rate shall includes Wrapping & Coating of
2.0
Under ground M.S. Heavy Grade Pipe -This corrosion protection tape shall comprise
coal tar component supported on fabric of organic (or) inorganic fibre and minimum
4mm thick and shall conform to requirement of IS:10221 code of practice for coating
and wrapping of under ground pipes line. The wrapping & coating tape to be cut to
200mm wide and wounding on pipe. Minimum 2.8m tape of 200mm wide per 150mm
pipe shall be considered.
a) 250 mm nominal dia Mtrs 234
b) 200mm nominal dia Mtrs 390
Delivered to site
c) 150 mm nominal dia Mtrs 510
d) 100 mm nominal dia Mtrs 18
SL.
DESCRIPTION UNIT QTY Remarks
NO
Supply, Erection, Testing and commissioning of Sluice valves as per IS 14846 and
PN 1.6 Rating, for Riser & External hydrant pipe line and Non rising spindle type with
3.0
flanges, bolts, nuts, washers, gaskets etc. The valve body, bonnet & wedge shall be
Cast Iron confirming to IS 210 FG200, SS spindle, CI handwheel etc.
a) 250mm nominal dia Nos. 3
b) 200mm nominal dia Nos. 10
Delivered to site.
c) 150mm nominal dia Nos. 19
d) 100mm nominal dia Nos. 19
Supplying, Installing, testing and commissioning of wafer type butterfly valves of Cast
iron body & disc confirming to IS 210 FG200, Nitrile rubber body seat & O ring
4.0
manufacturing standard to BS 5155, standard lever operated type completes flanges,
nuts, bolts etc. complete.
a) 150mm nominal dia (Four way FBI) Nos. 4 MDCC received. Will be dispatched soon.
Supplying, installing, testing and commissioning of Non-return valves of Cast Iron
body, cover & disc confirming to IS 210 FG200, manufactured as per IS:5312 (PN
5.0
1.6) reflux swing check type with required flanges, nuts, bolts and gaskets etc.
complete.
a) 150 mm nominal dia (Four way FBI) Nos. 3 Delivered to site.
6.0 Supplying, erecting and commissioning of Yard Hydrants
Supplying, erecting and commissioning of carbon steel body fire water monitor of 63
i mm diameter outlet with 360º horizontal & 180º vertical rotating mechanism, multi jet Nos. 12
nozzle and lever etc.
Single headed hydrant valve conforming to IS 5290, made of Stainless Steel (SS) with
ii 63 mm dia instantaneous outletof 80 mm dia fanged inelt, Blank caps , chain and CI Nos. 58
hand wheels etc complete. Delivered to site
15 M long, 63mm dia Reinforced Rubber Lined (RRL) hose conforming to IS 363 Type
iii B with stainless steel (SS) instantaneous couplings conforming to IS 903 and Hoses Nos. 116
shall be stored in side the hose cabinet.
iv Stainless Steel (SS) short branch pipe with 20 mm dia nozzle conforming to IS 903 Nos. 58
M.S. Hose cabinet stand mounted type fabricated out of M.S. sheet of 16 swg. with
glass fronted (4mm thick glass with rubber beeding) door and size of the cabinet shall
v be 900mm x 600 mm x 250 mm Quoted rate shall be includes suitable stand for Nos. 58 Delivered to site
mounting, all fasteners etc, and cabinet shall be red painted finish both inside and out
side.
Supplying, installing and commissioning of fire brigade inlet connection of 4 way with
1 no. 63 mm dia. built - in Gun metal instantaneous coupling type arranged on 150
7.0 Nos. 4
mm dia. Quoted rate shall be included M.S. cabinet of suitable size with mounting
supports etc. complete.
Fire brigade Inlet cabinet, surface mounted type fabricated out of M.S. sheet of 16 Delivered to site
swg. with glass fronted ( 4mm thick glass with rubber beeding) door and size of the
8.0 cabinet shall be 600mm x 350 mm x 350 mm Quoted rate shall be includes suitable Nos. 4
stand for mounting, all fasteners etc, and cabinet shall be red painted finish both
inside and out side.
Providing, Laying. Testing & Commissioning of RCC hume pipes of NP2 class with
suitable collars filling the recess at joints of pipes with hemp dipped in hot bitumen or
9.0 other suitable compound for chaulking of joint by jack, setting up of loose space over
the collar joints chaulked with CM 1:2, finished both ends to a slope of 1:1 including
curing, testing of pipes, etc., complete.
a 500mm nominal dia Mtrs 96
b 400mm nominal dia Mtrs 186 Partially delivered. Balance are dispatched
c 300mm nominal dia Mtrs 108 soon.
d 200mm nominal dia Mtrs 12
Supplying and erecting of Pre fabricated M.S structural steel supports such as angle,
Channel, Plate etc. conforming to relevant IS standards for laying above ground
10.0 Kg 7,500 Delivered to site.
Hydrant Pipe, Sprinkler pipe. Quoted rate shall inclusive of one coat of primer and one
coat of synthetic enamel paint of approved shade.
C INTERNAL HYDRANT SYSTEM
Supplying, installing, testing and commissioning of M.S Pipes confirming to IS 1239
Pt - I Heavy grade (Class-C), ERW, above ground pipe with suitable type of
supports (Shall be fabricated by M.S. Channel / Angle, anchor fasteners, bolts, nuts,
clamps, "U" bolt, malleable specials such as Reducers,Tees, elbows, flanges.
Including cutting, Welding, fixing in / on walls, ceiling by using suitable supports etc, .
1.0 The quoted rate shall also include for chasing / chipping walls, making bore holes in
walls whereever required and making them good with filler material. The exposed
pipes shall be protected by one coat of red oxide primer or zinc chromate primer and
two coats of synthetic enamel paint of fire red in color shade 536 as per IS 5. The
fittings shall be butt weld type for 65NB and above & socket weld type for 50NB and
below.
a) 150 mm nominal dia Mtrs 348
b) 100 mm nominal dia Mtrs 72
Delivered to site
c) 80 mm nominal dia Mtrs 90
d) 25 mm nominal dia Mtrs 60
SL.
DESCRIPTION UNIT QTY Remarks
NO
Supply, Erection, Testing and commissioning of Sluice valves as per IS 14846 and
PN 1.6 Rating, for Riser & External hydrant pipe line and Non rising spindle type with
2.0
flanges, bolts, nuts, washers, gaskets etc. The valve body, bonnet & wedge shall be
Cast Iron confirming to IS 210 FG200, SS spindle, CI handwheel etc.
a) 150mm nominal dia Nos. 9
Delivered to site.
b) 100mm nominal dia Nos. 3
Supplying, erecting and commissioning of Inernal Fire escape Hydrants (FEH) with
3.0
fire hose reel comprising the following items.
Single headed hydrant valve conforming to IS 5290, made of Stainless Steel (SS)with
i 63 mm dia instantaneous outletof 80 mm dia fanged inelt, Blank caps , chain and CI Nos. 54
hand wheels etc complete.
15 M long, 63mm dia Reinforced Rubber Lined (RRL) hose conforming to IS 363 Type
ii B with stainless steel (SS) instantaneous couplings conforming to IS 903 and Hoses Nos. 108
shall be stored in side the hose cabinet.
Delivered to site
iii Stainless steel (SS) short branch pipe with 20 mm dia nozzle conforming to IS 903 Nos. 54

First aid Hose reel conforming to IS 884 completes with 19 mm dia bore reinforced
braided rubber hose of 30 mtrs length fitted with 6.35mm dia shut off Nozzle, 25 mm
iv Nos. 54
dia ball valve etc. The hose reel shall be manual 180 deg. swining type with reel drum
hose shall be provided with coupling.
M.S. Hose cabinet stand / wall mounted type fabricated out of M.S. sheet of 16 swg.
with glass fronted ( 4mm thick glass with rubber beeding) door and size of the cabinet
v shall be750mm x 600 mm x 250 mm Quoted rate shall be includes suitable stand for Nos. 54 Delivered to site
mounting, all fasteners etc, and cabinet shall be red painted finish both inside and out
side.
Supplying and fixing of approved make of 25mm dia gun metal spring loaded
MDCC received.
4.0 automatic air release valve screwed end type with Pressure gauage, unions etc. Nos. 12
Will be dispatched soon.
complete.
Supplying, installing, testing and commissioning of Gun metal chrome finished Ball
5.0
valves with fittings of screwed end type.
a 25mm dia. Nos. 12 Delivered to site.
D EXTERNAL PIPING FOR AUTOMATIC SPRINKLER SYSTEM
Supplying, installing, testing and commissioning of M.S Pipes confirming to IS 1239
Pt - I Heavy grade (Class-C), ERW, above ground pipe with suitable type of
supports (Shall be fabricated by M.S. Channel / Angle, anchor fasteners, bolts, nuts,
clamps, "U" bolt, malleable specials such as Reducers,Tees, elbows, flanges.
Including cutting, Welding, fixing in / on walls, ceiling by using suitable supports etc, .
1.0 The quoted rate shall also include for chasing / chipping walls, making bore holes in
walls whereever required and making them good with filler material. The exposed
pipes shall be protected by one coat of red oxide primer or zinc chromate primer and
two coats of synthetic enamel paint of fire red in color shade 536 as per IS 5. The
fittings shall be butt weld type for 65NB and above & socket weld type for 50NB and
below.
a 200mm nominal dia Rmt 492
Delivered to site
b 150mm nominal dia Rmt 12
Supply, Installing, testing and commissioning of Heavy class M.S pipe, Class-C
ERW (as per IS-1239 Part-1) laid in under ground (1 Mtrs below ground level). The
quoted rate shall includes necessary specials like long radius bends, tees, including
cutting, welding / flanged joints with necessary washers, nuts, bolts, etc. also include
for providing concrete anchor blocks at all change in direction of pipeline if necessary
and also near each joints. The quoted rate shall includes Wrapping & Coating of
2.0
Under ground M.S. Heavy Grade Pipe -This corrosion protection tape shall comprise
coal tar component supported on fabric of organic (or) inorganic fibre and minimum
4mm thick and shall conform to requirement of IS:10221 code of practice for coating
and wrapping of under ground pipes line. The wrapping & coating tape to be cut to
200mm wide and wounding on pipe. Minimum 2.8m tape of 200mm wide per 150mm
pipe shall be considered.
a) 200 mm nominal dia Mtrs 66 Delivered to site.
Supply, Erection, Testing and commissioning of Sluice valves as per IS 14846 and
PN 1.6 Rating, for Riser & External hydrant pipe line and Non rising spindle type with
3.0
flanges, bolts, nuts, washers, gaskets etc. The valve body, bonnet & wedge shall be
Cast Iron confirming to IS 210 FG200, SS spindle, CI handwheel etc.
a) 200mm nominal dia Nos. 3 Delivered to site.
Providing, Laying. Testing & Commissioning of RCC hume pipes of NP2 class with
suitable collars filling the recess at joints of pipes with hemp dipped in hot bitumen or
4.0 other suitable compound for chaulking of joint by jack, setting up of loose space over
the collar joints chaulked with CM 1:2, finished both ends to a slope of 1:1 including
curing, testing of pipes, etc., complete.
Partially delivered. Balance are dispatched
a 400mm nominal dia Mtrs 54 soon.
Awaited for MDCC from MDCC.
SL.
DESCRIPTION UNIT QTY Remarks
NO
AUTOMATIC SPRINKLER SYSTEM FOR CEMENT BAG STORAGE ROOM AT
E
CEMENT PACKING PLANT
Supplying, installing, testing and commissioning of M.S Pipes confirming to IS 1239
Pt - I Heavy grade, ERW, above ground pipe with painting, suitable type of
supports ( Shall be fabricated by M.S. Channel / Angle, anchor fasteners, bolts, nuts,
1.0 clamps, "U" bolt, malleable specials such as Reducers,Tees, elbows, flanges.
Including cutting, Welding, fixing in / on walls, ceiling by using suitable supports
etc.The quoted rate shall also include for chasing / chipping walls, making bore holes
in walls whereever required and making them good with filler material.
a 150mm nominal dia Rmt 48
b 65mm nominal dia Rmt 108
Delivered to site
c 50mm nominal dia Rmt 18
d 25mm nominal dia Rmt 18
Supplying, Installing, testing and commissioning C.I. butterfly valves as per BS 5155
2.0 slim seal standared lever operated type with required flanges, nuts, bolts etc.
complete.
a 150mm nominal dia Nos 1 MDCC received. Will be dispatched soon.
Supplying, installing, testing and commissioning of standard pendent ESFR sprinkler
head with solder type sensing element, 20 mm screwed end connection of 74°C. MDCC received. Will be dispatched on
3.0 Nos 42
temperature rating, quick response type K 200 (K-14.0). The ESFR sprinklers shall be next week..
UL Listed / FM approved with natural brass finish.
Supplying, installing, testing and commissioning of hydralically operated Sprinkler
control valve complete with water motor gong bell, basic trims as required, pressure
4.0
gauges, pressure switch, drain valves, ball valves etc. complete. Alarm valve shall be
UL Listed / FM approved.
Inspection call raised on 28.02.2025.
a 150mm dia. Nos 1
Awaited for MDCC from LNVT.
Supplying, installing, testing and commissioning of flow switch (water flow detector) ,
5.0 paddle type on sprinkler distribution header on each floor and shall be connected to
Sprinkler annunciation panel for monitoring the status of the flow switch.

a 150mm nominal dia Nos 1 Delivered to site.

Supplying, installing, testing and commissioning of Gun metal chrome finished Ball
6.0
valves with fittings of screwed end type.
a 50mm dia.(Drain connection) Nos 2
Delivered to site.
b 25mm dia.( Air release valve & Inspector test connection) Nos 2
Supplying and fixing approved make 25mm dia. With automatic air release valve with MDCC received. Will be dispatch on next
7.0 Nos 1
unions etc. complete. week.
F MVWS SYSTEM FOR COAL SHED
Supplying, installing, testing and commissioning of G.I Pipes confirming to IS 1239 Pt
- I Heavy grade (Class-C), ERW, above ground pipe with suitable type of supports
(Shall be fabricated by M.S. Channel / Angle, anchor fasteners, bolts, nuts, clamps,
"U" bolt, malleable specials such as Reducers,Tees, elbows, flanges. Including
1.0 cutting, Welding, fixing in / on walls, ceiling by using suitable supports etc, The
aboveground pipe shall be painted with one coat of red oxide / zinc chromate primer
and two coats of sysnthetic enamel paint of fire red in colour as per IS 5 shade 536.
The pipe supports shall be painted with one coat of primer and two coats of anti
corrosive paint of approved shade.
b 100mm nominal dia Rmt 246
c 40mm nominal dia Rmt 258 Delivered to site.
d 25mm nominal dia Rmt 510
Supply, Erection, Testing and commissioning of C.I. Sluice valves as per ( PN 1.6
2.0
Rating, Non rising spindle type with flanges, bolts, nuts, washers, gaskets etc.
a 100mm dia. Nos. 12 Delivered to site.
Supplying, installing and commissioning C.I. flanged "Y" type Strainer with SS
3.0
mesh,suitable flanges, nuts, bolts, gaskets etc. complete.
a 100mm dia. Nos. 4 Delivered to site.
Supply installation and commissioning of Medium velocity Water spray nozzle (Open
4.0
type) Complete with all accessories.
Under manufacturing. Expect to raise
a Open type spray Nozzle K 64, 120° Nos 105
inspection call in mid of March.
Supply installation and commissioning of Coventional Sprinkler K 80, 79° C QB
5.0
detector
Under manufacturing. Expect to raise
a Sprinkler Bulb Nos 105
inspection call in mid of March.
Supplying, installing, testing and commissioning of hydraulically operated Deluge
6.0 valve, with water motor gong bell and trims as required, pressure gauges,Pressure
switch, drain valves, complete. Alarm valve shall be UL Listed / FM approved.
Inspection call raised on 28.02.2025.
a 100mm dia. Nos 4
Awaited for MDCC from LNVT.
SL.
DESCRIPTION UNIT QTY Remarks
NO
Supplying and erecting of Pre fabricated M.S structural steel supports such as angle,
Channel, Plate etc. conforming to relevant IS standards for laying above ground spray
9.0 Kg 2000 Delivered to site.
Pipe. Quoted rate shall inclusive of one coat of primer and one coat of synthetic
enamel paint of approved shade.
MVWS SYSTEM FOR COAL CONVEYORS (552 BC 01- 63.87mtr,552 BC 02 -
G
85m and 552 BC 03 - 77.36m)
Supplying, installing, testing and commissioning of G.I Pipes confirming to IS 1239 Pt
- I Heavy grade (Class-C), ERW, above ground pipe with suitable type of supports
(Shall be fabricated by M.S. Channel / Angle, anchor fasteners, bolts, nuts, clamps,
"U" bolt, malleable specials such as Reducers,Tees, elbows, flanges. Including
1.0 cutting, Welding, fixing in / on walls, ceiling by using suitable supports etc, The
aboveground pipe shall be painted with one coat of red oxide / zinc chromate primer
and two coats of sysnthetic enamel paint of fire red in colour as per IS 5 shade 536.
The pipe supports shall be painted with one coat of primer and two coats of anti
corrosive paint of approved shade.
b 100mm nominal dia Rmt 132
c 80mm nominal dia Rmt 84
d 65mm nominal dia Rmt 54
e 50mm nominal dia Rmt 42 Delivered to site
f 40mm nominal dia Rmt 36
g 32mm nominal dia Rmt 18
h 25mm nominal dia Rmt 978
Supply, Erection, Testing and commissioning of C.I. Sluice valves as per ( PN 1.6
2.0
Rating, Non rising spindle type with flanges, bolts, nuts, washers, gaskets etc.
b 100mm dia Nos 9 Delivered to site.
Supplying, installing and commissioning C.I. flanged "Y" type Strainer with SS
3.0
mesh,suitable flanges, nuts, bolts, gaskets etc. complete.
b 100mm dia. No 3 Delivered to site.
Supply installation and commissioning of Medium velocity Water spray nozzle (Open
4.0
type) Complete with all accessories.
Under manufacturing. Expect to raise
a Open type spray Nozzle K 22, 120° Nos 145
inspection call in mid of March.
Supply installation and commissioning of Coventional Sprinkler K 80, 79° C QB
5.0
detector
Under manufacturing. Expect to raise
a Sprinkler Bulb Nos 102
inspection call in mid of March.
Supplying, installing, testing and commissioning of hydralically operated Deluge
6.0 valve, with water motor gong bell and trims as required, pressure gauges, drain
valves, complete. Alarm valve shall be UL Listed / FM approved.
Inspection call raised on 28.02.2025.
a 100mm dia. No 3
Awaited for MDCC from LNVT.
Supplying and erecting of Pre fabricated M.S structural steel supports such as angle,
Channel, Plate etc. conforming to relevant IS standards for laying above ground spray
9.0 Kg 2300 71 kgs delivered to site.
Pipe. Quoted rate shall inclusive of one coat of primer and one coat of synthetic
enamel paint of approved shade.
H FIRE EXTINGUISHERS
Supplying, installing and commissioning Portable Fire extinguishers of following type
& capacity.
Carbon-di- oxide type fire extinguisher of 4.5 kgs. Capacity, CO2 gas as per IS 15222
1.0 with controll discharge mechanism fitted with Hose & Horn applicable on Class B fire Nos 78
rating 21B confirming to IS: 15683.

Mechanical Foam type fire extinguisher 9Lts. Capacity, with initial filling in brand new
cylinder with powder coated finish, fitted with Gun metal union, high pressure CO2
3.0 Nos 11
gas cartridge, hose and ABS type branch pipe and wall mounting bracket etc.
complete, confirming to IS: 15683:2008. The cylinder must carry ISI mark.

ABC powder type fire extinguisher of 6 Kgs. Capacity, with initial filling (Mono
Ammonium Phospate Powder 90) in brand new cylinder with powder coated finish,
4.0 Nos 132 Delivered to site.
Stored Pressur type, Pressure Gauge, Controllable discharge mechanism with Hose
& Nozzle , confirming to IS:15683. (ABC Dry Chemical Powder- MAP 90%)

ABC powder type fire extinguisher of 25Kgs.(outside cylinder) Capacity, trolley

mounted type with initial filling (Mono Ammonium Phospate Powder 90) in brand new
5.0 cylinder with powder coated finish, Stored Pressur type, Pressure Gauge, Controllable Nos 2
discharge mechanism with Hose & Nozzle , confirming to IS:10658. The extinguisher
shall be ISI marked.
Fire buckets round bottom type enamel painted, white inside & Red out side and
6.0 Nos. 44
Letter "FIRE" in black out side and handle with mounting bracket
7.0 Fire bucket stand fabricated by MS angles to install 4 Nos. of buckets. Nos. 11