6305443 - BISON EPOXY METAL BLISTER 24 ML MULTI LANGUAGE
EPOXY METAL
STRONG, METAL COLOURED TWO-COMPONENT EPOXY ADHESIVE
PREPARATION
Working Conditions: Recommended application at temperatures
between +10 °C and +35 °C. Product cures by mixing the resin
and hardener.
Personal safety: Preferably wear gloves.
Surface Requirements: The materials to be bonded must be dry,
clean, free of dust and grease.
Preliminary Surface Treatment: Degrease parts to be bonded with
acetone. Roughen smooth surfaces (sandpaper).
Tools: Mix the components in the double-syringe by means of
the supplied mixing bowl and spatula.
APPLICATION
Coverage: 1 ml = approx 10 cm² at a film thickness of 1 mm
Directions for use:
Remove the spatula from the side of the double syringe, and
the closure cap from the handle. Break the seal of the double
syringe.
Press out an equal amount of both components onto the
enclosed mixing tray. Mix these two equal parts well
with a synthetic spatula until a mixture is obtained with a
homogeneous colour. Apply the mixture, which at room
temperature (+20 °C) remains toolable for about 45 minutes,
as a thin layer on one of the two materials. Join the materials
and keep them in place for 10 hours. Be careful not to move
PRODUCT DESCRIPTION the parts before the adhesive has cured. After use, clean the
Strong, metal coloured two-component epoxy adhesive nozzle with a cloth and place the special cap in the handle on
the double syringe. Resin and hardener must not come into
FIELD OF APPLICATION
contact with each other unless for usage.
Ideal for strong repairs of metal objects which must withstand
Stains/residue: Remove wet stains immediately with warm
extreme conditions (forces, vibrations, (sea)water, heavy load),
water and soap. Cured adhesive residue can only be removed
such as tools, car parts, engines, (motor)bikes, metal (garden)
mechanically.
fencing and cutlery. Also suitable for sealing a small hole in a
Points of attention: After use close well (note: always place back
radiator. Suitable for bonding of metal (steel, aluminium, iron)
the cap in the same way, due to the bonding of the cap to the
together and in combination with stone, wood, concrete, and
double syringe). For optimum performance it is important to
various synthetics (such as formica, polyester and bakelite).
create a larger amount of adhesive and mix it very well. Curing
Not suitable for Polyethylene (PE), polypropylene (PP), PTFE and
time depends on the temperature. Adhesive does not cure below
silicone rubber.
+5 °C.
PROPERTIES
· Extreme strength: up to 220 kg/cm²
· Metal coloured
· Resistant to harsh conditions
· Resistant to temperatures between -40 °C and +120 °C
· Filling
· (Sea)water resistant
· Very good chemical resistance
· Can be sanded, filed, drilled and painted after curing
Our advice is based on extensive research and practical experience. However, in view of the large variety of materials and the conditions under which our products
are applied, we assume no responsibility for the results obtained and/or any damage caused by the use of the product. Nevertheless, our Service Department is
always at your disposal for any advice needed.
Bison International B.V. - P.O. Box 160 - NL 4460 AD Goes www.bison.net 1
20241003
6305443 - BISON EPOXY METAL BLISTER 24 ML MULTI LANGUAGE
EPOXY METAL
STRONG, METAL COLOURED TWO-COMPONENT EPOXY ADHESIVE
TECHNICAL SPECIFICATIONS
Chemical base: Epoxy resin
Chemicals resistance: Water, oil, grease, solvents,
diluted acids and alkalis
Colour: Grey
Consistency: Pasty
Density approx.: 1,2 g/cm³
Filling capacity: Very good
Final bond strength (Alu): 22 N/mm²
Final bond strength after: 24 hours
Handling time: 12 hours
Minimum application 5 °C
temperature:
Minimum temperature -40 °C
resistance:
Maximum temperature 120 °C
resistance:
Moisture resistance: Good
Mixture ratio: 1:1
Potlife: 45 min
Solvent free: Yes
UV resistance: Very good
Viscosity: Thixotropic
Water resistance: Good
Water soluble: No
STORAGE CONDITIONS
Store cool, dry, frost-free, upright (nozzle upwards) and tightly
closed.
Our advice is based on extensive research and practical experience. However, in view of the large variety of materials and the conditions under which our products
are applied, we assume no responsibility for the results obtained and/or any damage caused by the use of the product. Nevertheless, our Service Department is
always at your disposal for any advice needed.
Bison International B.V. - P.O. Box 160 - NL 4460 AD Goes www.bison.net 2
20241003
