Scribd
Upload
26 views8 pages

Change Parts

The document outlines the specifications for cable glands used in the Wayang Windu Units 1 and 2 retrofits project, detailing material requirements based on cable size and installation conditions. It specifies the use of polycarbonate plastics for smaller cables and aluminum for larger ones, with particular attention to sealing and ingress protection (IP66) against H2S gas. Additionally, it provides guidance on installation locations and types of cable glands required for various environments, ensuring proper grounding and support for cable loads.

Uploaded by

Gigih J Wisda
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
26 views8 pages

Change Parts

The document outlines the specifications for cable glands used in the Wayang Windu Units 1 and 2 retrofits project, detailing material requirements based on cable size and installation conditions. It specifies the use of polycarbonate plastics for smaller cables and aluminum for larger ones, with particular attention to sealing and ingress protection (IP66) against H2S gas. Additionally, it provides guidance on installation locations and types of cable glands required for various environments, ensuring proper grounding and support for cable loads.

Uploaded by

Gigih J Wisda
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 8

Cable Gland Specification (Unit1)

Owner
STAR ENERGY GEOTHERMAL
(WAYANG WINDU) LIMITED
Project
WAYANG WINDU UNITS 1 AND 2
RETROFITS PROJECT
Contract No. Origin
3200001256 FH
Contractor
CONSORTIUM OF
FUJI ELECTRIC CO., LTD. &
PT. WASA MITRA ENGINEERING
SEGWWL Drawing No. Revision

WWRP1-EE-EC-8261 0
Internal drawing No.PD520931
Dwg. Status

FOR CONSTRUCTION
DOCUMENT SUBMITTAL STATUS :
☐ FOR INFORMATION ☐ FOR REVIEW ☒ FOR CONSTRUCTION ☐ AS-BUILT

0 Issued for construction 2024/07/16 S.Tsuji N.watanabe J.Yamamoto


Rev Description Date Prepared Checked Approved
Specification of Cable Gland
Regarding the cable gland, materials should be selected by ambient air condition include H2S Gas.
And installation parts should be decided for each situation as follows.

1. Material of cable gland


Kind of cable Cable Outer Diameter Material

22mm or Less Polycarbonate Plastics


Power / C & I Cable
More than 22mm Aluminum

Grounding Cable All Polycarbonate Plastics

2. Location of cable gland installation


Location Install Type of cable gland Remarks

For bottom cable


entry part of Panel /
Cubicle and terminal
Box, sealing putty
Not Applicable Not Applicable should be applied
instead of cable
gland.
It is separate from the
Air open air.
Conditioning Area
Indoor
For cable entry part
Armored
of Panel / Cubicle and
Applicable No Biting
Terminal Box without
Type
bottom part.

No Air
Applicable -
Conditioning Area Polycarbonate
or
Aluminum
IP66
Outdoor - Applicable -

3. Supply Cable Gland : Armored-No Bite Type


Cable gland should isolate inside of Panel / Cubicle / Terminal-Box from outside open air included H2S Gas
at cable entry part. [Ingress Protection : IP66]
There are Long cable entry holes of terminal Boxes electrical equipments.Therefore, Armored No Biting type
cable gland should be adopted. Please refer to following drawings for detail of cable gland installation.
Cable load should be supported by conduit, cable tray and cable bracket.
Armor （Wire / Tape ）should be grounded inside of each panel, cubicle and terminal box.

[2/8]
0
3-1. Typical Installation of Armored Cable
（Long Cable Entry Hole of Terminal Box）

[3/8]
0
3-2. Typical Installation of Armored Cable
（Thin Cable Entry Hole of Terminal Box）

[4/8]
0
3-3. Typical Installation of Non-Armored Cable

[5/8]
0
4. Detail Dimension of Cable Gland

[6/8]
Aluminum Type
SAMPLE

[7/8]
Polycarbonate Type
SAMPLE

[8/8]

You might also like