Frequently Used Commands List
Parameters Setting Commands Query Commands Description
IP or domain name can be set, the format remains the same;
Sever IP Modification IP,122.9.115.220,,7711 Not Applicable
The data in RED should be replaced to your own.
IP or domain name can be set, the format remains the same;
Dual Sever IP Settings ( 808 Protocol ) DUALIP,11.39gps.com,7808,11.008gps.com,7700# Not Applicable
The data in RED should be replaced to your own.
Reply: Version+ID+IP+Port+APN+GPS Status+GSM Signal, etc;
Query Status Not Applicable CXZT
See Remark in Details.
Please note there is a space before the number;
Set Administrator admin123456 13580000000 Not Applicable
The data in RED should be replaced to your own.
Delete Adminitstrator noadmin Not Applicable
Set ID Number ID,8168000008# Not Applicable The data in RED should be replaced to your own.
Activate Anti-Theft SF Not Applicable To realize Vibration Alarm.
Deactivate Anti-Theft CF Not Applicable
Restore Factory Settings FORMAT Not Applicable APN and IP remain the same after restoring
In order to ensure the safety of the vehicle, the terminal only performs
Fuel / Oil Cut Off DY Not Applicable the fuel and electricity cut-off operation when the GPS is in a valid
positioning state and the vehicle speed is less than 20km/H or when
Resume Fuel / Oil KY Not Applicable the vehicle is stationary.
Release Speed SMS Command: SZCS#SOURCE_OFF_TYPE=1
Query Location by SMS Not Applicable G1234 The reply will be an uncorrected URL.
Command: 123
Command: 666# Fixed Return to AMAP Link for 123
Query Latitude & Longitude Link Not Applicable Command: URL#
Command: POSITION# Return to Google Link for 666#, URL#, POSITION#, DWXX#
Command: DWXX#
Unit: minute;
After the vehicle is stationary for 10 minutes, the device goes
Set Sleep Time after Stationary SLEEPT,123456,10 Not Applicable into sleep mode. ( Default as 3 minutes );
No sleep mode if revising it as 0;
The data in RED should be replaced to your target value.
Device Restart CQ Not Applicable
For APN with account and password, please set as:
APN Settings NAPN=cmnet,, Not Applicable NAPN=cmnet,123,666
The data in RED should be replaced to your local one.
General Commands List
Parameters Setting Commands Query Commands Description
Query Version Not Applicable CXCS#SOFTVERSION Query only, can not be set; Or send " CXZT " Through SMS.
Query ICCID Not Applicable CXCS#ICCID Query only, can not be set;
Terminal Number ( ID Number ) SZCS#TERIID=2175100001 CXCS#TERIID The data in RED should be replaced to your own.
Domain and IP can be set;
Sever Address SZCS#SERVIP=122.9.115.220#SERVPORT=7711 CXCS#SERVIP#SERVPORT Or send the command as: IP,122.9.115.220,,7711
The data in RED should be replaced to your own.
Domain and IP can be set; Requires software to support dual ID
The Second Sever Address SZCS#SERV2_ADDR=122.0.64.102#SERV2_PORT=7700 CXCS#SERV2_ADDR#SERV2_PORT settings; JT808 Protocol is required.
The data in RED should be replaced to your own.
Unit: second, the limit value should be greater than 5;
Position Uploading Interval SZCS#FREQ=30 CXCS#FREQ
The data in RED should be replaced to your target value.
Unit: second, the limit value should be greater than 10;
Heartbeat Packet Uploading Interval SZCS#PULSE=180 CXCS#PULSE
The data in RED should be replaced to your target value.
Device IMEI Number SZCS#IMEI=356946010000010 CXCS#IMEI The data in RED should be replaced to your own.
Vehicle Owner Phone Number SZCS#USER=13500000000 CXCS#USER The data in RED should be replaced to your own.
Unit: minute;
Set Sleep Time after Stationary SZCS#SLEEPT=3 CXCS#SLEEPT
The data in RED should be replaced to your target value.
Unit: km/h
Over Speed Alarm SZCS#SPEED=120 CXCS#SPEED Alarm when the speed is greater than 120 km/h;
The data in RED should be replaced to your target value.
Parameters Setting Commands Query Commands Description
Platform Protocol Setting;
0 for TQ
Protocol Switch SZCS#PTL_SEL=0 CXCS#PTL_SEL
1 for JT808
The data in RED should be replaced to certain value.
0 for 2011 version
1 for 2013 version
Version Configuration for 808 Protocol SZCS#808SEL=0 CXCS#808SEL
( Default as 2011 version)
The data in RED should be replaced to certain value.
666 is APN account, 123 is APN password; If there is no account and
password for your local APN, please directly set as:
APN Settings SZCS#APN=cmnet#USERPPP=666#PWPPP=123 CXCS#APN#USERPPP#PWPPP
SZCS#APN=cmnet
The data in RED should be replaced to your local one.
1 for allowed
0 for prohibited
Corner Supplementary Uploading SZCS#ANGLE_SEND=1 CXCS#ANGLE_SEND
( Defualt as allowed )
The data in RED should be replaced to certain value.
1 for allowed
0 for prohibited
Blind Zone Supplimentary Uploading SZCS#BLIND_EN=1 CXCS#BLIND_EN
( Defualt as allowed )
The data in RED should be replaced to certain value.
E is for East, + is for time zone, Beijing is East Eighth District, the
command is set as: SZCS#GMT_SET=E0800
Timezone Settings SZCS#GMT_SET=E0800 CXCS#GMT_SET W is for West, - is for time zone, Washingtong is West Fifth
District, the command is set as: SZCS#GMT_SET=W0500
The data in RED should be replaced to your own.
It is only available for deivces with 2 wires;
0 for Associated
Vibration Associated ACC SZCS#ACCLINE=0 CXCS#ACCLINE 1 for Detecting ACC Line
( Default as 1 )
The data in RED should be replaced to certain value.
Requires an relay to be connected with;
0 is for cutting off when the speed is less than 20 km;
Fuel Cut Off Method SZCS#SOURCE_OFF_TYPE=0 CXCS#SOURCE_OFF_TYPE
1 is for immediately cutting off;
The data in RED should be replaced to certain value.
Vibration level 1-6, Default as 1;
Vibration Sensitivity SZCS#VIBL=1 CXCS#VIBL
The data in RED should be replaced to certain value.
Parameters Setting Commands Query Commands Description
Advise NOT to revise it
The sample means the device will be waken up once the
Detect the time of vibrations to wake
SZCS#VIBCHK=10:5 CXCS#VIBCHK vibrations are detected for 5 times in 10 seconds;
the device
Default as 3 times in 10 seconds;
The data in RED should be replaced to your target value.
Fixed as 4-Digits;
The first digit 1 for allowed, 0 for prohibited;
The last 3-digit is for voltage parameters;
2G OBD Voltage Associated ACC SZCS#EXP_ACC=1138 CXCS#EXP_ACC
The sample shows that the ACC will be displayed as on once the
voltage is detected as 13.8V;
The data in RED should be replaced to your target value.
The first digit 1 for allowed, 0 for prohibited;
135 means the voltage is 13.5V when ACC ON;
4G OBD Voltage Associated ACC SZCS#ACC_CFG=1,135,130 CXCS#ACC_CFG
130 means the voltage is 13.0V when ACC OFF;
The data in RED should be replaced to your target value.
The function is only available for OBD Device;
1 for allowed;
Voice-Activated Recording Function SZCS#VOICE_CTRL_EN=1 CXCS#VOICE_CTRL_EN
0 for prohibited;
The data in RED should be replaced to certain value.
Unit: Second
Default as 300
808 Protocol Upload Position in Sleep
SZCS#ACC_OFF_FREQ=300 CXCS#ACC_OFF_FREQ Upload heartbeat packets and positioning data after the device
Mode
sleeps;
The data in RED should be replaced to your target value.
0 means the mileage is reset to zero every day;
Mileage in JT808 Protocol SZCS#DIS_UNCLR=0 CXCS#DIS_UNCLR 1 means mileage has been accumulated;
The data in RED should be replaced to certain value.
Mileage Reset to Zero in JT808 Protocol MILEAGE=0# Not Applicable Unit: km
0 means to send V1 message after sleep;
1 means to send BIN message after sleep;
Message Upload Settings in TQ Protocol SZCS#TQ_SEL=0 CXCS#TQ_SEL
2 means keep GPS state after sleep;
The data in RED should be replaced to certain value.
Parameters Setting Commands Query Commands Description
1 for Activate
Deactivate WiFi for 4G Device with JT808
SZCS#WIFI_ENABLE=0 CXCS#WIFI_ENABLE 0 for Deactivate
Protocol
( Default as Activate )
1 for allowed;
ACC Associated Anti-Theft Settings +
SZCS#DET_AUTO_ACC=1#ACCLOCK=1 CXCS#DET_AUTO_ACC#ACCLOCK 0 for prohibited;
Automatic Setting Anti-Theft
The command should be all set as 1.
Unit: minute;
Set Auto-Armed Time SZCS#ACCLT=3 CXCS#ACCLT Default as 3 minutes;
The data in RED should be replaced to your target value.
The value is fixed as 6 characters, 1 and 2 are the speed when
the angle value is required. 3 is the separator, and 4, 5, 6 is the
Set Parameters for Angle Value SZCS#ANGLEVALUE=10-015 CXCS#ANGLEVALUE angle change for supplementary uploading.
( Default value as speed is greater than 10km/h, and the angle is
15 degrees. )
Set the time to automatically restart the
SZCS#GPS_RST_TIME=300 CXCS#GPS_RST_TIME Default as 300 seconds
GPS when the GPS is not positioned
> To connect the terminal with a UDP server remotely, and
specify the IP port.
> The maintenance server will provide SMS transparent
SZCS#GPS_MONI_EN=1#GPS_MONI_IP=192.168.0.1 CXCS#GPS_MONI_EN#GPS_MONI transmission, remote monitoring, GPS raw data monitoring,
Remote Maintenance Server
#GPS_MONI_PORT=1000 _IP#GPS_MONI_PORT hardware status query and other functions
> The maintenance server and the business server work
independently, without affecting the current working state of
the terminal.
1 for Activate
GPS Drift Optimization SZCS#GPS_FINTER_EN=0 CXCS#GPS_FINTER_EN 0 for Deactivate
( Default as Activate )
Set the command for dialing the owner number only.
Number Answering Restrictions SZCS#AUTO_ATA=0 CXCS#AUTO_ATA
1 for no restrictions
Parameters Setting Commands Query Commands Description
J16/808 protocol with WiFi function;
1 for allowed;
WiFi Function SZCS#WIFI_ENABLE=1 CXCS#WIFI_ENABLE 0 for prohibited;
Default as 1;
The data in RED should be replaced to certain value.
1 for Activate
Vibration Alarm Through SMS SZCS#VIB=1 Not Applicable
0 for Deactivate
1 for Activate
Vibration Alarm Through Phone Call SZCS#VIBCALL=1 Not Applicable
0 for Deactivate
1 for Activate
Power Failure Alarm Through SMS SZCS#POF=1 Not Applicable
0 for Deactivate
1 for Activate
Power Failure Alarm Through Phone Call SZCS#POFS=1 Not Applicable
0 for Deactivate
1 for Activate
SOS Alarm Through SMS SZCS#SOS_SMS_EN=1 Not Applicable
0 for Deactivate
1 for Activate
SOS Alarm Through Phone Call SZCS#SOS_CALL_EN=1 Not Applicable
0 for Deactivate
1 for Activate
ACC Alarm Through SMS SZCS#ACC_SMS_EN=1 Not Applicable
0 for Deactivate
1 for Activate
ACC Alarm Through Phone Call SZCS#ACC_CALL_EN=1 Not Applicable
0 for Deactivate
1 for Activate
Over Speed Alarm Through SMS SZCS#SPDSMSEN=1 Not Applicable
0 for Deactivate
Set SOS Number 1 SZCS#SOS_CODE2=13580000001 Not Applicable Phone Number: 13580000001
Set SOS Number 2 SZCS#SOS_CODE3=13580000002 Not Applicable Phone Number: 13580000002
Voice Control Threshold Value SZCS#VOICE_DB_VALUE=73 Not Applicable 73dB, can be modified.
Voice Detection Time SZCS#VOICE_DB_TIME=3 Not Applicable Unit: Second, 3 is detection time.
Voice Control Cold Down Time SZCS#VOICE_REDO_DELAY=1 Not Applicable Unit: Minute, 1 is cool down time.
