Metal Access Control Manual

1 2 3

4 5 6

7 8 9

*
EXIT
8
ADD
#
CALL

DEL REV
1.Introduction 4.Installation
The series of product is a new generation of multi-functional standalone access control. It adopts Remove the back cover from the keypad using the supplied special screw driver
new ARM core 32-bit microprocessor design, which is powerful, stable and reliable. It contains Drill 2 holes on the wall for the self-tapping screws and hole for the cable
reader mode and standalone access control mode etc.. It’s widely applied to different occasions, Put the supplied rubber bungs to into the two holes
such as office, residential communities, villa etc.. Fix the back cover firmly on the wall with 2 self-tapping screws
Thread the cable through the cable hole
Attach the keypad to the back cover. (as following illustration)

2.Features
remote area

Feature Specification

Read 125KHz EM Card and HID Card (Optional)

Card Type
Read 13.56MHz Mifare card and CPU card (Optional)

Keypad Characteristic Operate by infrared remote

Output Way Contain reader mode, the transmission format could be adjusted by users.

Access Way Support multi access ways: Card, multi cards

Admin Card Support admin card

User Capacity 10,000 card users

5.Wiring
Unlocking Signal Relay NO/NC/COM output
No. Color Marks Description
1 Green D0 Wiegand input (Wiegand output as reader mode)

2 White D1 Wiegand input (Wiegand output as reader mode)

3.Technical Specifications 3 Grey ALARM Alarm signal MOS tube drain output end (optional)

4 Yellow OPEN/ BEEP Exit button input end (Beeper input as reader mode)
Operating Voltage: DC 12-24V Standby Current: ≤ 35mA
5 Brown D_IN/ LED Door contact switch input end (LED input as reader mode) (optional)
Operating Current: ≤100mA Operating Temperature: -35℃~60℃
6 Red +12V Positive power supply
Operating Humidity: 0%~95% Electric lock signal relay contact current ≤1A
7 Black GND Negative power supply
Alarm signal MOS tube output current: ≤1A Unlocking time: 0~300s adjustable
8 Blue NO Relay NO end

9 Purple COM Relay COM end

10 Orange NC Relay NC end

1 2
6.Diagram 6.2 Special Power Supply

6.1 Common Power Supply

D0 Green
Green
D1 White
White
OPEN Yellow Electric control lock
Yellow
Exit button
Exit button
D_IN Brown Brown
Door contact

Special power supply

Door contact Magnetic lock
COM Purple Purple

Black Black
GND

Grey
ALARM Grey
Alarm Alarm
Red
NC Orange Magnetic lock
Blue
+12V Red
Orange

NO Blue

Note: The door contact and alarm function are optional Note: The door contact and alarm function are optional

3 4
6.3 Reader Mode 7.Sound and Light Indication
Operation Status Light indicator Buzzer
Stand by Red
Operation successful Green Beep—
Operation failed Beep-Beep-Beep
Admin card enter programming Beep-Beep
Admin card exit programming Beep—
Press digital key Beep
Green
Press * key Beep—
On process of reading multi user card Red indicator flash slowly
White
Enter programming mode Red indicator flash slowly
Enter setting status Orange
Grey
Unlocking Green
Buzzer alarm Red indicator flash quickly Alarm
Yellow

Brown
8.Admin Menu
Red 8.1 Standalone Mode Settings

Device Management
Black
Enter Default
programming Menu Operation steps Description value
Access controller 0 New admin code # new admin
Blue code # Change admin code 999999

10001# Read card* Set admin add card

Purple Press * 1
Admin code # 10002# Read card * Set admin delete card
(Default
Orange 10001# * Delete admin add card
admin code is
2
"999999") 10002# * Delete admin delete card

11 # Standalone access control mode

3 12 # Relay toggle mode
11
13 # Reader mode
( 26-58 ) # Wiegand 26-58 bits output

5 6
Add and Delete Users Advanced Settings
Enter Default
programming Menu Operation steps Description
value Enter Menu Operation steps Description Default
programming value
Read card ... * Add card users continuously
(0-300) # Door opening time range: 0-300S 5
4 0 equals to 50mS
Press 8 or 10 digits card
Add card users by card number
number # … * “…” means (0-99) # Alarming time range: 0-99 min.
1 5 0
repeating the
Press ID number # Read Add card users by specific ID previous
operation, Press ID number
card … * number
Press * Press * key # press 8
Admin code # Press ID number # Press 8 to exit. or 10 digits card
Add card users by specific ID number # Add conductive number card
(Default or 10 digits card number # 7
number and card number Press * input card
admin code is …*
Admin code # quantity #
"999999") Delete users (Default
admin code is
Delete card users by reading 0# Normal working mode
Read card … * “…” means "999999")
card repeating the The external alarm and built-in buzzer
previous 1# will work if wrong operations are over 5
Press 8 or 10 digits card Delete card users by card number operation,
2 number #… * times. 0
Press * key
Press ID number # … * Delete users by ID number to exit. The device will be locked out for 10 min
8 2# if wrong operations are over 5 times.
0000# Delete ALL users
3# Disable light indicator
4
4# Enable light indicator
Access Ways 5# Disable buzzer
6
6# Enable buzzer
Enter Menu Operation Description Default
programming steps value

Press *Admin code # 0# Entry by card

(Default admin code 0
is "999999") 3 2-10 # Entry by multi-card

7 8
8.2 Reader Mode Settings 10.2 Reset to Factory Default
Users can reset to the factory default when the admin code is forgotten, or the default settings
Enter Default have been modified disorderedly, operations as below:
programming Menu Operation steps Description
value Power off, press and hold the exit button continuously, power on, release the exit button until
hearing beep sound twice, the admin code has been reset to 999999, factory default settings
Press * New admin code # Repeat are successful.
0 new admin code # Change admin code 999999
Admin code #
(Default Note: Registered user data won’t be deleted when reset to factory default.
(13) # Reader Mode
admin code is 3
"999999") (26-58) # Wiegand 26-58 bits output 26

9.Admin Operation
9.1 Add Users
Read admin add card , Read the 1st user card Read the 2nd user card …, Read admin add card

Note The admin add card is used to add card continuously and quickly. When you read the
admin add card at the first time, you will hear short "BEEP" sounds twice and the indicator light
turns orange, it means you have entered into add user programming, when you read the admin
add card at the second time, you will hear long "BEEP" sound once and the indicator light turns
red, it means you have exited the add user programming.

9.2 Delete Users

Read admin delete card , Read the 1st user card Read the 2nd user card …, Read admin delete card

Note The admin delete card is used to delete card continuously and quickly. When you read
the admin delete card at the first time, you will hear short "BEEP" sounds twice and the indicator
light turns orange, it means you have entered into delete user programming, when you read the
admin delete card at the second time, you will hear long "BEEP" sound once, the indicator light
turns red, it means you have exited the delete user programming.

10. Other Operation

10.1 Remove Alarm
Read valid card or Press admin code#
Note When the alarm is activated, users can remove the alarm by reading a valid card or pressing
valid admin code.

9 10