TECHNICAL DATA SHEET
PROMASTIC No. TD
Revision
: E-008
: 04
EPM-60110 Effective Date : 14/06/2023
PRODUCT DESCRIPTION & USES
PROMASTIC EPM-60110 is a two component modified epoxy surface and flash rust tolerant paint.
This product is used as anti corrosion paint for ship bottom, cargo hold, inside or outside of
accommodation space, void space, cofferdam, engine room, pipe line, others steel structure, and non
ferrous metal such as aluminum, fiber, etc. It can be used for maintenance and repair.
FEATURES
• Good abrasive and impact resistance
• Good toughness
• Good corrosion resistance
• Flash rust tolerant
• As a primer or topcoat
• Pencil Hardness 2H
• Fast dry version is avaiable upon request.
PRODUCT SPECIFICATION
Colors : Standard and custom colors
Volume Solid : 80 + 2%
Specific Gravity : 1.45 + 0.05 g/cc
Flash Point : 250C
Packaging : 5 & 20 Liter set
Storage Stability : Two years if it is stored in cool and dry place, also in its original not
opened package. (Do not store below freezing point)
APPLICATION
Instruction for Use : Stir well before use, preferable by means use mechanical mixer to
ensure good homogeneity
Application Condition : 25 – 35 °C, 60 – 80 % RH
Mixing Ratio by Volume :
A Component B Component
: = 4 : 1 (v/v)
(EPM-60110) (EPMH-60110 PS)
Thinner : THME-90100, THME-90120, etc
Application Method : Airless spray Air spray Brush/Roller
Thinning Ratio by Volume : 0 - 10% 15 – 30% 0 – 5%
Tip Size for Airless Spray Gun : Approx. 0,48 mm (0,019 inch) Air Pressure : approx. 160 bar/2300 psi
Nozzle Orifice for Air Spray : Approx. 1-1.5 mm Air Pressure : approx. 3-4 bar/40-60 psi
Wet Film Thickness (WFT) : 125 – 250 microns or 5.1 – 10.2 mills
Dry Film Thickness (DFT) : 100 – 200 microns or 4.1 – 8.1 mills
Theoretical Coverage : 5.33 m²/litre set (DFT = 150 microns)
Pot Life : 30oC 35oC
2 – 3 hours 1 – 2 hours
FILM PROPERTIES
Drying Time (@ DFT = 150 mic) : 30oC 35oC
Surface Dry : 20 – 30 min 15 – 25 min
Hard Dry : 4 – 5 hours 3.5 – 4.5 hours
Full Cure : 7 days (30°C)
Page 1 of 2
PT. PROPAN RAYA I.C.C | Jl. Gatot Subroto KM. 8 Tangerang 15810, Indonesia
P: +62 215930 3333 | F : +62 21 5924 694 | W : www.propanraya.com | E : info@propanraya.com
Re-coating Interval : Minimum 6 hours (300C)
Maximum 6 weeks*
Provide adequate ventilation during application and drying.
*consult with Propan representative for the detail
RECOMMENDED COATING SYSTEM
Primer Coat : PROMASTIC EPM-60110
Intermediate Coat : According to Specification
Finish Coat : According to Specification
Recommended Dry Film Thickness : 1 coat (150 microns / coat)
SURFACE PREPARATION
1. All surfaces should be clean, dry and free from contamination.
2. Oil or grease should be removed by solvent cleaning or industrial detergent.
3. Remove the rust with mechanical sander or with chemicals.
4. Blast cleaning with suitable blasting material minimum Sa2, hand or power tool cleaning to a
minimum standard of St2 in accordance with the ISO 8501-1 : 1988 or SSPC- SP – 2.
5. Provide adequate ventilation during application.
INSTRUCTION FOR USE
Prepare one mixture (A+B) as much as needed for application.
Firstly stir well Comp. A EPM - 60110 until homogeneous, add Comp. B EPMH - 60110 PS and mix thoroughly.
Mix ratio Comp. A : Comp. B = 4 : 1 (by volume). Mixed material could apply using airless spray, brush or
roller. Use Thinner THME-90120 as solvent cleaner. Do not apply the mixed material after pot life time is over.
Provide adequate ventilation during application and drying.
SAFETY PRECAUTION
Avoid contact with the skin and eyes. Wear suitable protective coating, such as overalls, goggles, dust
mask, and gloves. Use barrier cream. Provide adequate ventilation during application. Do not breathe
vapor of spray. This product is flammable. Do not smoke. Use only explosion proof equipment.
FIRST AID:
General : In all cases of doubt, or when symptoms persist, seek medical attention. Never give
anything by mouth to an unconscious person.
Eyes : In the case of accidental splashes, flush eyes with clear running water for 5 minutes
while holding eyelids open. If irritation persist, seek medical attention.
Skin : Wash off thoroughly with plenty of water and soap. Do not use solvent or thinner.
Removed contaminated clothing. If irritation persist, seek medical attention.
Inhalation : Remove affected person to fresh air area, loosen collar, provide oxygen if breathing is
difficult. If affected person is not breathing, administer CPR and seek emergency
medical attention.
Note : Epoxy coatings will characteristically chalk and fade upon exposure to sun ligh
DISCLAIMER
This document contains information issued based on the best and latest of Propan’s knowledge in
accordance to laboratory testing and practical application experience. The end user must test the
product’s suitability for their specific application and purpose. Propan shall not be liable for defects where
the application of the Product has not been made fully in accordance with the recommendations and
requirements. This document is subjected to change without further notice. Please consult Propan for
any specific guidance on the suitability of this product for their needs or for any specific application
practices.
Page 2 of 2
PT. PROPAN RAYA I.C.C | Jl. Gatot Subroto KM. 8 Tangerang 15810, Indonesia
P: +62 215930 3333 | F : +62 21 5924 694 | W : www.propanraya.com | E : info@propanraya.com
