Scribd
Upload
31 views2 pages

UD-800 - SM - Inspection List

The document is an inspection checklist for the UD-800 device, detailing various inspection items categorized into basic, operation, detailed, and performance inspections. Each section requires the inspector to mark 'Yes' or 'No' for specific criteria, ensuring the device meets operational and safety standards. The checklist also includes sections for inspection results confirmation and comments for any points of notice.

Uploaded by

Department Technical
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
31 views2 pages

UD-800 - SM - Inspection List

The document is an inspection checklist for the UD-800 device, detailing various inspection items categorized into basic, operation, detailed, and performance inspections. Each section requires the inspector to mark 'Yes' or 'No' for specific criteria, ensuring the device meets operational and safety standards. The checklist also includes sections for inspection results confirmation and comments for any points of notice.

Uploaded by

Department Technical
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

[UD-800] Inspection List OSP-4-93-00

Serial Number: Judgement PASS FAIL


(Software Ver.: )
Date: Approval Signature
Temperature & Humidity °C / %

Customer Name:
Distributer Name:
Preparer Signature:

1.Basic Inspection
[Common Inspection] (Mark Yes/No after your inspections)

Yes No Inspection Items Required Tool


□ □ Repair unit was cleaned up / sanitized before starting investigation. -
□ □ Serial number label is attached to the machine. -
□ □ Serial number on the serial number label can be recognized. -
□ □ No breakages or loosen power cable, inlet or fuse holder. -
□ □ No dents, bruises on exterior body. -
□ □ Date and customer settings can be stored correctly. -
□ □ Operation manual is equipped. -

[Operation Inspection] (Mark Yes/No after your inspections)

Yes No Inspection Items Required Tool


□ □ Measurement mode change can be done by operating touch panel. -
□ □ Brightness adjustment function on UTILITY menu works. -
□ □ Sound volume adjustment function on UTILITY menu works. -
□ □ Date & Time setting on UTILITY menu can be done. -
Freeze function on B-Diag mode works by pressing FREEZE button
□ □ -
on monitor or stomping FREEZE pedal of the footswitch.
Data storage to USB memory stick on B-Mode mode works by
□ □ -
stomping a SAVE/PRINT pedal of the footswitch.
□ □ Mode change can be done. [B-Mode], [Axial], [Pachy], [A-Diag] -
□ □ Test piece auto-measurement can be done properly on AXIAL mode. -
Test piece manual-measurement can be done properly on AXIAL
□ □ -
mode.
Measured data on AXIAL mode can be printed out by pressing a PRINT
□ □ -
button.

OSP-0-14-00 - 1/2 -
[UD-800] Inspection List OSP-4-93-00

2. Detailed Inspection
Yes No Inspection Items Required Tool
Software version is the latest in case there’re no restrictions to the
□ □ -
customer’s usage environment.

[Performance Inspection] (Mark Yes/No after your inspections)

Yes No Inspection Items Required Tool


Axial Probe
Measured value of test piece is within the range on a label.
[SN: ]
□ □ Measured value: mm, degree
Pachy Probe
[Range on label: mm to mm]
[SN: ]
□ □ Basic artifact can be seen on the monitor. 10MHz
□ □ No mechanical / electric noise from the probe. B-scan Probe
□ □ No cracks, no bruises on the probe cap. [SN: ]

3. Inspection Results
[Confirmation of Inspection Results] (Mark Yes/No after your inspections)

Yes No Inspection Items Required Tool


□ □ Repair unit was cleaned up / sanitized before packing and shipping. -

[Comments] (Please write down if you have a point of notice)

OSP-0-14-00 - 2/2 -

You might also like