Specifiers’

Guide
AUSTRALIA
November, 2014

Marblo® is a registered Trademark of Marblo (Holdings) Pty Limited.

The “Marblo Blocks” logo design ©2014 Marblo (Holdings) Pty Limited, all rights reserved.
Marblo Group Pty Limited is a member of the Marblo (Holdings) Pty Limited group of companies.
INDEX

INTRODUCTION Page 2

“TRADITIONAL” SOLID SURFACE SHEETS Page 3

 Solid Colours Plain (P), Galaxy (GX), Granada (GR) & Stone (S) Page 3
o Custom “Made-to-Order” Range
o Marblo PLUS “Price Fighter Range”
o Technical — Solid Colours

“TRANSLUCENT“ SOLID SURFACE SHEETS Page 5

 Frost / Opal Series (NOL1, NOL2 & NOL3) Page 5
o Custom “Made-to-Order” Range
o Marblo PLUS “Price Fighter Range”
o Technical - Opal / Frost

 Pearl Series (NPR) Page 7

o Custom “Made-to-Order” Range
o Marblo PLUS “Price Fighter Range”
o Technical — Pearl Series

 Fire Rated Translucent (OFR, FR & FRT) Page 9

o Opal FR (OFR5 & OFR6)
o FR & FRT (FR5, FR6, FRT5 & FRT6)
o Technical — Opal FR, FR and FRT

NATURE COLLECTION DECORATIVE PANELS Page 10

 Storm, Bedrock & Wave Page 10
o Technical - Storm, Bedrock & Wave
 Suspense Page 11
o Suspense
o Suspense “Premier”
o Technical - Suspense & Suspense “Premier”
 PebbleStone Page 12
o Technical - PebbleStone

MARBLO® DESIGNER BATH-WARE Page 13

SPECIFICATION CONSIDERATIONS Page 14

HOW TO SPECIFY Page 16

1
INTRODUCTION

Marblo® is available with differing formulations ranging from advanced chemical, stain and fire
resistant series as required in industrial laboratories, to special decorative series suited to an
extremely broad range of applications and a multitude of aesthetic effects.

Our range of solid surface sheet materials can be fabricated to form even the most complex 3-
dimensional shapes by authorised Marblo® fabricators, using conventional woodwork tools and
machinery. In the event of long term wear or mishap, the materials usually can be refurbished to
look like a new installation where other materials may need replacement. Marblo® colour matched
joint adhesive, provides not only for seamless joints, but also has hygienic benefits for food
preparation and laboratory applications. Marblo® joints are not heat welded, but are formed using a
liquid form of the same Marblo® colour to achieve the best possible joint match.

The Marblo® range of pre-finished decorative sheets known as the Nature Collection affords the
ability to be cut and installed by a competent tradesperson, delivering the most economical solution
to supply feature panels in residential and commercial projects alike.

All Marblo® materials share in the company’s commitment to innovation and quality manufacturing.

Products

To meet the differing needs of the international solid surface market place, Marblo® materials are
available in the following series:
 Solid Colour (Traditional Plain and Speckled) Solid Surface Sheets

Plain Colour (P) Galaxy (GX) Granada (GR) Stone (S)

 Translucent & Semi-Translucent Solid Surface Sheets

Frost (NOL1) Opal (NOL2) Opal (NOL3) Pearl (NPR)

 Nature Collection (“Stone” Effect Translucent) Decorative Panels

Storm Bedrock Wave Suspense PebbleStone

 Marblo® Designer Bath-ware (Basin and Vanity Tops)

Marblo® solid surface sheets are available in both Custom “Made-to-Order” colours and sizes to
provide the greatest flexibility and Marblo® PLUS “Price Fighter Range” in the most popular colours
and sizes to provide the greatest savings.

2
“TRADITIONAL PLAIN & SPECKLE” SOLID SURFACE SHEETS

Solid colours have excellent heat, stain and chemical resistant properties.

Custom “Made-to-Order” Range

Solid Colours:
 Plain (P) - Solid colours
 Galaxy (GX) — Small size speckles
 Granada (GR) — Medium size speckles
 Stone (S) — Stone effect chips

Colours: Large selection of colours available in the standard range.

Matching to Dulux / Pantone is available subject to lead-time.
TM TM

Dark colours may require greater care & maintenance.

Standard widths: 650mm, 760mm, 900mm plus 1050mm.

Standard lengths: 2700mm & 3500mm

Standard thickness: 6mm, 9mm, 12mm, 16mm, 18mm, 20mm & 26mm
(Non-standard sheet sizes and thickness within manufacturing limits are also
available; refer to your Marblo distributor for more details).

Recommended
Surface Finish: Satin (Low-sheen) as per samples supplied
Gloss for “Stone Series” materials, as per samples supplied.
Dark colours may require gloss finish to bring out the depth of colour.
Matte, Satin, Semi-Gloss, Gloss and High Gloss finish can be nominated by the
specifier.

Lead-time: 10 working days delivery (metro areas), standard colours.

(Subject to quantity. Sheets only - excluding fabrication by third parties).

Marblo® PLUS Range — Solid Colours

Colours: Limited offering of the most popular colours, please visit www.marblo.com.au
or contact your local Marblo® distributor to view the Marblo® Plus range of
Solid Colours.

Available width: 650mm & 760mm (900mm is available in limited colours)

Available length: 3500mm

Available thickness: 12mm (20mm limited colours only)

Recommended
Surface Finish: Semi Gloss, as per samples provided.
Matte, Satin, Semi-Gloss, Gloss and High Gloss finish can be nominated by the
Specifier.

Lead-time: Ex-warehouse, Sydney (Sheets only - subject to availability, excluding

Fabrication).
3
Technical — Solid Colours

Use: Suitable for high temperature / high chemical environments such as laboratory
applications, kitchen bench tops and splash backs.

High Traffic
Applications: In extremely high traffic applications, light plain colours or light colours with
chips are recommended to minimize the appearance of scratching and
scuffing.

Jointing: Matching Marblo® adhesive is available to create seamless joints.

Joints should be seamless and un-obtrusive.

Substructure: Solid Colours require full substructure support. Substructure of HMR MDF,
HMR Particle board or ply wood is acceptable and framing / lattice sub-strates
are not required. The use of thicker Marblo® such as 20mm has been used on
bar tops and the like to minimize support or to provide un-supported cantilever
of up to 150mm.
Please refer to Marblo® Fabrication Manual or contact your local Marblo® office
for specific advice.

Weight: 20.4 kg/m2 for 12mm thick material (nominal)

34.0 kg/m2 for 20mm thick material (nominal)
Specific gravity is 1.7 g/cc (nominal)

Thermo-forming
(Heat Bending): Solid Colours are NOT thermo-form.
Thermoform grade “Plain Solid Colours” and “Galaxy Series” is available only
on request and must be noted in specifications and at time of order. “Granda
Series” and “Stone Series” ARE NOT available in Thermoform grade.
Marblo® PLUS Range Solid Colours are NOT thermo-formable.

Warranty: Ten (10 Year) Limited Warranty

Fire Rating: CLASS 2 BCA C1.10a

4
TRANSLUCENT SOLID SURFACE SHEETS

OPAL SERIES (TRANSLUCENT & SEMI-TRANSLUCENT) SHEETS

Custom “Made-to-Order” Range

As the name suggests, Marblo® “Custom Range” is made-to-order to provide flexibility in terms of
colour selection, level of translucency, thicknesses and sheet sizes.

Opal Series:
 Frost (NOL1) — Almost fully translucent with colour
 Opal (NOL2) — Semi-translucent
 Opal (NOL3) — Less translucent / more opaque

The Marblo® formulation, colour and thickness will all affect the final translucency of translucent
materials. Before specification and or ordering materials, please contact your local Marblo®
distributor for a production sample in the colour and thickness to be used.

Colours: Over 1,000 colours available in the range.

Matching to Dulux / Pantone is available subject to lead-time.
TM TM

Dark and more highly saturated colours require greater care and maintenance
depending on the application.

Standard widths: 650mm, 760mm, 900mm plus 1050mm.

Standard lengths: 2700mm & 3500mm

Standard thickness: 6mm, 9mm, 12mm, 16mm, 18mm, 20mm & 26mm
(Non-standard sheet sizes and thicknesses within manufacturing limits are
also available; refer to your Marblo distributor for more details).

Recommended
Surface Finish: Satin (low Sheen), as per samples provided.
Matte, Satin, Semi-Gloss, Gloss and High Gloss finish can be nominated by the
Specifier.

Lead-time: 10 working days for manufacture & delivery (metro areas).

(Subject to quantity. Sheets only - excluding fabrication by third parties).

5
Marblo PLUS Range - Opal Series

Introduced as our “price leader”, Marblo® PLUS is a series of selected colours in standard sheet
sizes and thicknesses. Marblo® PLUS delivers true savings for your solid surface requirements.

Colours: Selected popular colours, please visit www.marblo.com.au or contact your

local Marblo® distributor to view the full Marblo® PLUS colour range.

Available width: 1220mm

Available length: 3050mm

Available thickness: 12mm

Recommended
Surface Finish: Satin (low Sheen), as per samples provided.
Matte, Satin, Semi-Gloss, Gloss and High Gloss finish can be nominated by the
Specifier.

Lead time: Stock Colours: Ex-warehouse Sydney (Sheets only, subject to availability)
Special Order: 12 week Lead-time (Sheets only, excluding fabrication, Subject
to minimum order and shipping costs).

Technical - Opal Series

Use: NOT suitable for laboratory applications, kitchen bench tops and splash backs
or areas where heat is a concern.

Jointing: Matching Marblo® adhesive is available to create seamless joints.

Due to the translucent nature of materials, joints will be visible.
The more translucent the material (Frost NOL1), the more visible the joint the
more dense the material (Opal NOL3) the less viable the joint.

Substructure: Opal materials were designed for decorative applications and require underside
support for horizontal applications. The use of thicker Marblo® such as 20mm
has been used on bar tops and the like to minimize support or to provide un-
supported cantilever of up to 150mm.
The use of Marblo® Opal Series for backlighting will require supports at
nominal 600mm — 800mm centers depending on application.
Please refer to Marblo® Fabrication Manual or contact your local Marblo® office
for specific advice.

Weight: 13.2 kg/m2 — 16.8 kg/m2 for 12mm thick material (nominal)
22.0 kg/m2 - 28 .0kg/m2 for 20mm thick material (nominal)
Specific gravity is 1.1-1.4 g/cc (nominal).

Thermo-forming
(Heat Bending): Opal Series sheets are Thermo-formable.
500mm minimum radius at 12mm thickness.

Warranty: Ten (10 Year) Limited Warranty

Fire Rating: CLASS 3 BCA C1.10a

6
PEARL SERIES SHEETS

Pearl Series:
 Pearl NPR — Translucent with a Pearl Vein Effect

The Marblo® formulation, colour and thickness will all affect the final translucency of translucent
materials. Before specification and or ordering materials, please contact your local Marblo®
distributor for a production sample in the colour and thickness to be used.

Custom “Made-to-Order” Range - Pearl Series

Colours: Over 30 colours available in the range.

Matching to Dulux / Pantone is available subject to lead-time.
TM T

Dark colours may require greater care & maintenance.

Standard widths: 650mm, 760mm, 900mm plus 1050mm.

Standard lengths: 2700mm & 3500mm

Standard thickness: 6mm, 9mm, 12mm, 16mm, 18mm, 20mm & 26mm
(Non standard sheet sizes and thicknesses within manufacturing limits are
also available; refer to your Marblo distributor for more details).

Recommended
Surface Finish: High Gloss, as per samples provided.
Matte, Satin, Semi-Gloss, Gloss and High Gloss finish can be nominated by the
Specifier.

Lead-time: 10 working days delivery (metro areas), standard colours.

(Subject to quantity. Sheets only - excluding fabrication by third parties).

Marblo PLUS Range - Pearl Series

Colours: Selected popular colours in both “Ex-Stock” and “Special Order”.

Please visit www.marblo.com.au or contact your local Marblo® distributor to
view the full Marblo+ Plus colour range.

Available width: 1220mm

Available length: 3050mm

Available thickness: 12mm

Recommended
Surface Finish: High Gloss, as per samples provided.
Matte, Satin, Semi-Gloss, Gloss and High Gloss finish can be nominated by the
Specifier.

Lead time: Stock Colours: Ex-warehouse Sydney (Sheets only, subject to availability)
Special Order: 12 week Lead-time (Sheets only, subject to minimum order and
shipping costs).

7
Technical — Pearl Series

Use: NOT suitable in high traffic applications and areas where heat or stain
resistance is a concern such as laboratory applications, kitchen bench tops and
splash backs.

Jointing: Matching Marblo® adhesive is available to create seamless joints.

Due to the highly translucent nature of materials, joints will be visible.
Allow for flow of pattern / vein effect when jointing sheets.

Substructure: Pearl materials were designed for decorative applications and require
underside support for horizontal applications.
The use of Marblo® Pearl Series for backlighting will require supports at
nominal 600mm centers depending on application.
Please refer to Marblo® Fabrication Manual or contact your local Marblo® office
for specific advice.

Weight: 13.7 kg/m2 for 12mm thick material (nominal)

22.0 kg/m2 for 20mm thick material (nominal)
Specific gravity is 1.1 g/cc (nominal).

Thermo-forming
(Heat Bending): Pearl Series sheets are Thermo-formable.
500mm minimum radius at 12mm thickness.

Warranty: Ten (10 Year) Limited Warranty

Fire Rating: CLASS 4 BCA C1.10a

8
OPAL FR & FR SERIES SHEETS “Fire Rated”

Fire Rated Translucent Range:

 Opal FR (OFR5 & OFR6) — Semi-translucent but with better fire / heat rating
 FRT (FRT5 & FRT6) — Semi-translucent with high fire, stain and chemical resistance.

ONLY available in Custom “Made-to-Order” Range

Colours: Selection of colours available in the standard range.

Matching to Dulux / Pantone is available subject to lead-time.
TM TM

Dark colours will require greater care & maintenance.

Standard widths: 650mm, 760mm, 900mm plus 1050mm.

Standard lengths: 2700mm & 3500mm

Standard thickness: 6mm, 9mm, 12mm, 16mm, 18mm, 20mm & 26mm
(Non standard sheet sizes and thicknesses within manufacturing limits are
also available; refer to your Marblo distributor for more details).
Recommended
Surface Finish: Satin, as per samples provided.
Dark colours may require a gloss finish to bring out the depth of colour.
Matte, Satin, Semi-Gloss, Gloss and High Gloss finish can be nominated by the
Specifier.

Lead-time: 10 working days delivery (metro areas), standard colours.

(Subject to quantity. Sheets only - excluding fabrication by third parties).

OPAL FR & FR - Technical

Use: Opal FR (OFR) NOT suitable for laboratory or kitchen bench tops.
FR & FRT are suitable for laboratory applications or kitchen bench tops.

Jointing: Matching Marblo® adhesive is available to create seamless joints.

Joints will be visible. As the products as less translucent than standard Opal
materials, jointing will be less visible.

Substructure: Opal FR and FR Series require full underside support for horizontal
applications. The use of thicker Marblo® such as 20mm has been used on bar
tops and the like to minimize support or to provide un-supported cantilever of
up to 150mm.
Please refer to Marblo® Fabrication Manual or contact your local Marblo® office
for specific advice.

Weight: 20.4 kg/m2 for 12mm thick material (nominal)

34.0 kg/m2 for 20mm thick material (nominal)
Specific gravity is 1.7 g/cc (nominal).

Thermo-forming
(Heat Bending): Opal FR (OFR) are Thermo-formable
FR (FR) are NOT Thermo-formable.

Warranty: Ten (10 Year) Limited Warranty

Fire Rating: CLASS 2 BCA C1.10a

9
NATURE COLLECTION DECORATIVE PANELS

Nature Collection panels are pre-finished, ready to be cut and installed by a competent
tradesperson (please refer to Installation Instructions before working material).

Nature Collection is currently available in the following ranges:

 Storm
 Bedrock
 Wave
 Suspense
 PebbleStone

Storm, Bedrock and Wave Series

Colours: Selected colours, patterns and finishes, please visit www.marblo.com.au or

contact your local Marblo distributor to view the full selection.

Available width: 1220mm

Available lengths: 2440mm (3050mm available subject to Special Order).

Available thickness: 6mm and 12mm

Surface Finish: Pre-finished* Satin face

* Additional finishing may be required.

Lead-time: Stock Colours: Ex-warehouse Sydney NSW, subject to availability.

Special Order: 12 week Lead-time.

Technical - Storm, Bedrock and Wave Series

Use: Recommended as vertical decorative panels ONLY, unless adequate support is

provided, please contact your local Marblo® office for project related
assistance.

Jointing: Nature Collection is generally not recommended for “seamless jointing”

Joints should be featured using clear silicone and “V” Butt joints or “Bird’s
Mouth” Detail.

Substructure: Nature Collection materials as designed for decorative applications and require
full boarder support for vertical applications. Clear fins and or clear backing
may be required.
Contact your local Marblo® office for project related assistance.

Weight: 8 kg/m2 for 6mm thick material (nominal)

Specific gravity is 1.3 g/cc (nominal)

Thermo-forming: Bedrock & Wave Series are thermoform grade.

Storm Series is NOT thermoform grade, available in thermoform grade subject
to Special Order.

Warranty: One (1 Year) Limited Warranty

Fire Rating: CLASS 3 BCA C1.10a

10
Suspense Series

Colours: Selected natural and man-made materials suspended in clear resin, please
visit www.marblo.com.au or contact your local Marblo distributor to view the
full Nature Collection.

Available width: 1220mm

Available lengths: 2440mm (3050mm available subject to Special Order).

Available thickness: 8mm — 12mm depending on thickness of materials inside

Surface Finish: Pre-finished* Frosty face and back

Lead-time: Stock Colours: Ex-warehouse Sydney NSW, subject to availability.

Special Order: 12 week Lead-time.

Suspense “Premier” Series

Colours: Selected natural and man-made materials suspended in clear resin, please
visit www.marblo.com.au or contact your local Marblo distributor to view the
selection.

Available width: 1220mm

Available lengths: 2440mm (3050mm available subject to Special Order).

Available thickness: 8mm — 12mm depending on thickness of materials inside

Surface Finish: Pre-finished* “luster” face and back

Lead-time: Special Order: 12 week Lead-time.

Technical - Suspense

Use: Recommended as vertical decorative panels ONLY.

Jointing: Nature Collection is generally not recommended for “seamless jointing”

Joints should be featured using clear silicone and “V” Butt joints or “Bird’s
Mouth” Detail.

Substructure: Nature Collection materials as designed for decorative applications and require
full boarder support for vertical applications. Clear fins and or clear backing
may be required.
Contact your local Marblo® office for project related assistance.

Weight: 11 kg/m2 for 10mm thick material (nominal)

Specific gravity is 1.1 g/cc (nominal — depending on material)

Thermo-forming
(Heat Bending): NOT available in thermoform grade

Warranty: One (1 Year) Limited Warranty

Fire Rating: CLASS 4 BCA C1.10a

11
PebbleStone Series

Colours: Selected natural tumble pebbles suspended in clear resin, please visit
www.marblo.com.au or contact your local Marblo® distributor to view the full
selection.

Available sizes: 600mm x 600mm

600mm x 1220mm
1220mm x 2440mm

Available thickness: 20mm

Surface Finish: Pre-finished Gloss face

Lead-time: Special Order — 12 week lead-time.

Technical — PebbleStone

Use: Recommended as vertical decorative panels ONLY.

Jointing: PebbleStone is NOT recommended for “seamless jointing”

Joints MUST be featured.

Working: Stone mason tools to be used to cut, trim and finish PebbleStone materials.
Standard solid surface methods and procedures should NOT be used.

Weight: 44kg/m2 for 20mm thick material (nominal)

Specific gravity is 2.2 g/cc (nominal — depending on material)

Thermo-forming
(Heat Bending): NOT available in thermoform grade

Warranty: One (1 Year) Limited Warranty

Fire Rating: CLASS 4 BCA C1.10a

12
DESIGNER BATH-WARE

A range of fully moulded basins and integrated vanity tops by renowned Australian designers.
 MoJoTM Collection — Free standing baths, pedestals and bench mounted basins.
 Slab Collection — integrated vanity top with moulded basin

Colours: White

Style: To view the Marblo® basin and bath-ware range, please visit
www.marblobathware.com.au or leading bathroom showrooms Australia-wide.

Surface Finish: Gloss

(Matte available on request)

Warranty: Ten (10 Years) Limited Warranty

Lead-time: Ex-warehouse Sydney NSW, subject to availability.

13
SPECIFICATION CONSIDERATIONS

During the specification process for Marblo materials, the following should be considered.

“Green Star” Rating

Marblo® materials have been used on numerous “5 Green Star” rated projects due to its long
product life and low manufacturing emissions. Please refer to “Commitment to the Environment”
statement in the PDF downloads section of www.marblo.com.au

Interior Use Only

All Marblo materials are intended for INTERIOR USE ONLY, direct sunlight may eventually cause
fading, yellowing or possible distortion of the material in excessive heat conditions.
In some applications, light solid colours have been used for exterior applications. Before
specification, refer to the Marblo® Fabrication Manual or contact your local Marblo® office.

Sample Colours
Due to varying levels of translucency and material thickness that are available, it is critical when
selecting colours that you obtain a sample of the nominated Marblo® material.
It should be noted that, dark and more highly saturated colours may require greater maintenance
depending on the application. Please also allow for the fact that production may differ from sample
due to batching. Large installations of materials may also show a different hue due to factors such
as lighting in the installed environment.

Surface Finish
Marblo® Accredited Fabricators will produce materials in the “Recommended Surface Finish”
detailed herein UNLESS an alternate surface finish is nominated.

Substructure
All Marblo® materials require adequate structural supports in the form of a full substrate or
perimeter support made from HMR or equivalent materials. When bonding or affixing Marblo
materials, flexible adhesives should be used.
Refer to Marblo® Fabrication Manual or contact your local Marblo® office for specific advice.

Paint to Back of Translucent Sheets

When translucent materials are to be affixed to joinery or other surfaces, it is recommended to
paint the rear of the Marblo® sheet with white acrylic paint or resin to stop the substructure and
glue from showing through.

Thermal Expansion
The linear thermal expansion for 12mm thick Marblo solid colour range, is +/-1mm per metre at +/-
20ºC. A minimum of 3mm at each end should be allowed between the Marblo material and walls or
other rigid ends. If a bench top run exceeds 3 lineal meters a further 1mm should be allowed for
every additional meter. If expansion gaps are required to be filled, only a flexible silicone should be
used. Adequate clearance must be allowed for any fixtures such as plumbing that protrude through
the material and never screw directly into Marblo® materials.

Edge Profiles
To reduce the occurrence of chipping, ALL exposed edges or Marblo® materials should be radiused.
Minimum 3mm radius is recommended with 5mm radius or greater to be used for applications such
as movable tabletops. Square edges and arrissed edges should be avoided.

Internal Corners
All internal corners should have a minimum 6mm radius. For cook-top cutouts, the largest radius
possible that can be achieved but no less than 12.5mm radius is recommended.
Refer to Marblo® Fabrication Manual or contact your local Marblo® office for specific advice.

14
Translucent Materials
(Opal, Pearl, Opal FR & Nature Collection)

 Surface Finish (Lustre)

If the required lustre is different to the recommended surface finish provided on Marblo®
samples, obtain a production sample in the nominated luster finish before materials are
ordered.
Changing the Opal finish from satin to high gloss for example, may result in the base colour
appearing darker and more vibrant, it may also provider greater levels of translucency.

 Thickness of Material
The greater the thickness the darker the colour may appear (lower light transfer). Reduced light
transfer may occur and additional lighting may be required (where the products are to be back-
lit).

 Level of Translucency
Less translucent materials may give the base colour a darker appearance (lower light transfer).
More translucent materials may give the base colour a lighter appearance (greater light
transfer).
Less translucent materials such as NOL3, Opal FR (OFR) and Fire Rated Translucent (FR) will
result in reduced light transfer, additional lighting may be required (where the products are to
be back-lit).

 Backlighting
When backlighting Marblo, consideration should be given to the following:
• The intensity of the light source to be used.
• Allowance for circulatory airflow to prevent build up of excessive heat.
• Suitable service access to the light fitting.
• Distance from light source
• Light “hot spotting”
• Shadows caused by supports and framing.
Your local Marblo® office can assist with general advice and suggestions regarding backlighting
of Marblo® materials and provide examples of various specifications employed in previous
projects.

 Joint Position
Due to the nature of translucent materials, joints — even seamless joints — will be noticeable
and in many cases obvious.
Nominating joint positions and even featuring of joints must be considered when specifying
these ranges of materials.
Please refer to Marblo® Fabrication Manual or contact your local Marblo® office for specific
advice.

 Site Access
Although Marblo® Opal and Pearl Series materials are available in large sheet sizes of up to
3500mm long, restriction of access at the installation site (due to lift heights, corridors and stair
wells) may require site joints which may be visible or may require featuring.

 UV Stable Silicone
Only UV stable silicones should be used to affix and or bond translucent Marblo® materials.

15
HOW TO SPECIFY

• Supplier:
Marblo® (refer to www.marblo.com.au for details of local distributor / Marblo office.

• Specify nominal thickness:

6mm, 9mm, 12mm, 16mm, 18mm, 20mm or 26mm

• Specify series — colour — code:

(eg. Marblo® PLUS “White Snow” MSA-101-P or
“Opal Series “Day Light” NOL2 7198-W)

• Specify lustre:
(eg. Matte, low sheen, semi-sheen, semi-gloss, gloss, high gloss)

• Specify fabrication and installation:

Ensure all work is completed by an authorised Marblo fabricator. Contact your local Marblo®
office for a list of fabricators in your city.

• Sample:
Obtain production sample of each colour specified in the nominated thickness and submit to
specifier for approval prior to commencement of works.

16
Related publications:

Material Safety Data Sheet

Installation Recommendations — Nature Collection

Care & Maintenance — Marblo® PLUS Solid Surface Sheets

Care & Maintenance — Marblo® Bath-ware

Marblo® Solid Surface Fabrication Manual

Marblo® PLUS Solid Surface Sheet 10 Year Limited Warranty

Marblo® Solid Surface Sheet 10 Year Limited Warranty
Marblo® Bath-ware 10 Year Limited Warranty

DISCLAIMER:
info@marblo.com.au
Information provided herein is solely for the purpose of a general guide only www.marblo.com.au
and may be subject to revision as new knowledge becomes available. It is not intended to imply nor shall it be construe to
provide the opinion or recommendation of Marblo Group Pty Ltd as to the appropriateness and or fitness of any product or
material for any purpose or use.
Although Marblo Group Pty Ltd has taken care in the preparation of this document it shall not be liable to any party for the
correctness or completeness of the same, nor the use of any information contained herein for any specific purpose or use.
For product availability and or information relating to the use of Marblo® materials for a specific use or purpose,
contact your local Marblo Group Pty Ltd office or distributor.
None of the technical information contained herein shall supersede the Marblo® fabrication manual or the best
industry practice.

17