Cavitation RF RPO

User Manual
Contraindication Users Guide
1.Operation schematic drawing of 40K cavitation explode work head
1.Pregnant women or women during menses. Massage the fat of thigh in circles
2.Epileptic
3.Patients with malignancy.
4.Patient whose wound after operation has not healed up.
5.Acute inflammation or epidemical patients.
6.Those with heart diseases or with heart pacemaker.
7.Those with kidney (gall-stone) disease.
8.Those with embedded metal object or silica gel.
9.Those in menses, under birth control, with emiction incontinence period, or undergone 2.Operation schematic drawing of sextupole RF laser head for body
belly operation. Waist and abdomen care (25 minutes, 2-3 days/time)
10.Those with genetic hypersensitivity.

NOTICE
1.Be sure to use the special ultrasonic gel.
2.Handle the heads with care, avoid knocks.
3. Use and prepare enough gel to avoid overheating the heads.
4.Don't linger too long on a single region and avoid the bones.
5.Don't use disinfectants to disinfect the heads, use wet cotton or dry towel instead.
6.Make sure the power supply is connected and plugged well.
7.If the machine is not for use for a long period of time, switch it off and unplug the power
supply. ①
























②































③





























④⑤⑥















⑦⑧
8.Operators and patients should not wear any metallic jewellery or items.
9.The machine should be rested every hour of continuous operation for about 10 minutes.
10.During the operation,be sure not to accept other treatments.
①.Massage to navel as center and gradually expanding the range

②.Massage chest nest, both sides of former abdomen and below the
navel (in diamond formation) from inside to outside in circles.

③.Concentrated on the fat from 4 directions the navel as center

LASER LASER

④.Massage from inner rib to outer edge in circles.

⑤.Massage from end of pelvis to groin in circles.

⑥.Massage back and forth from inner rib to outer edge in straight line.

⑦.Lift the Hip and the lower part of the body care (30minutes, 2-3 days/time)

⑧.Concentrated from hip to groin in circles or straight line. Repeat massaging from inner to
FACE RF Package Including: outer edge. Recycle the motion.
EYE RF
Eye RF handle *1
Face RF handle *1 3. Operation schematic drawing of FACE RF work head for face.
Body RF handle *1
BODY RF CAVI CAVI handle *1 1. Massage the mandible center in circles to produce deep heat.
VAC RF handle *1
Cold handle *1 2. Massage lower jaw in lines.
VAC RF BIO& photon handle *1
EMS handle *1 3. Massage the triangle zone of both sides of the face in circles.
EMS Laser Lipolysis *8
Power cord *1 4. Massage from jaw to angulus oris to ear in lines.
Belt *2
BIO& photon Bracket *3
COLD

1 10
 BIO Microcurrent & LED photon Treatment 40Khz Ultrasonic handle (Cavitation)
Application : forehead. eyes' around, cheek, mouth, double chin, neck, body Strong sound wave explosion fat head - with collective strong sound wave head, strong
Microcurrent-safe and painless facial helps erase fine lines and wrinkles, while firming sound wave of 40KHZ may be emitted to human body for impacting fat cells fiercely and
your skin and defining your features causing friction motion between fat cells. This may cause effective consumption of calories
and moisture in fat cells and reduce the size of fat cell. What's more, sound wave vibration
may cause fierce impact
of fat cells to make them be exploded instantaneously, reduce the amount of fat cells and
thereby achieve the effects of removing fat.

There is 4 mode of M1, M2, M3 and M4 as described as follows:

"M1" is continuous working for 3 sec and discontinuous for 3 sec.
"M2" is continuous working for 2 sec and discontinuous for 2 sec.
"M3" is continuous working for 1 sec and discontinuous for I sec.
"M4” is continuous working for 0.5 sec and discontinuous for 0.5 sec.
Operate with the 40KHz cavitation head for 15-20 minutes with mainly the spiral movement
on body

Method : Use the probe to massage the specific part of skin to be treated circularly after
applying the essence
adjust the output energy and mode

There are 4 modes, M1, M2, M3, and M4, which are described as follows:
"M1" works continuously, "M2" works continuously for 2 seconds, and pauses for 2 seconds.
"M3" works continuously for 1 second and pauses for 1 second. "M4" works continuously for
0.5 seconds and pauses for 0.5 seconds.

The handle can adjust 7 photon modes. First, turn on the switch on the machine screen to Press "-” “+” to adjust the duration of operation.
ensure that the power is greater than 0,Press "-" "+" to adjust the LED color. Touch to ajust the cavitation mode among M1,M2,M3,M4 modes.
. Clicking "-" to decrease the strength or click “+" to increase it.
Press "START" to start the strong sound wave explosion fat head.

Method : Use the probe to massage the specific part of skin to be treated circularly after
applying the slimming cream for about 15 to 20 minutes. It could quicken the blood
1. Red: Vitalize be suitable for any skin, promote blood circulation, and regenarate circulation in the treated part of skin and has the effect of decomposing fat.
collagen protein in order to smooth skin and heal xerodermia, exuviation, degenerate
losing hair and folliculosis. Matters needing attention:
2. Green:Balance Normalize sebaceous glands, Reduce black heads and sores,
balance moisture. 1. Apply slimming cream or cooling gel to the part of skin to be treated before the treatment.
3. Blue: Calm be suitable for sensitive, oil, and comedo skin-diminish and eliminate 2. Keep close contact between the probe and the skin.
acne bacilus to remove acne, whelk, promote to compound protein with ossein, 3. Adjust the intensity from low level to high level.
activate skin, tighten slack skin and gravidity winkle. 4.Do not keep the applicator at the same place
4. Purple: Drain Renew skin, reduce wrinkles. 5.Move the applicator slowly, But constantly
5. Orange: Brighten whiten decompose pigment, and smooth scares. 6.Avoid the treatment over bone and do not aim directly to the joint
6. Cyan: Defense strengthen the ability to protect skin, calm down, release stress. 7.Pay attention to the temperature of the cavitation handle when using it, and stop using
7. White: Guide guide skin to absorb nutrients and anti-aging. it for ten minutes after half an hour of use.
8. Loop 8. Cavitation is forbidden to work without gel. If it doesn't work and you need to re-adjust
the frequency, please contact the supplier.

9 2
Vacuum Bipolar RF handle Cold treatment
1. Help skin firmness, maintain elasticity, prevent allergies and other problems;
2. Shrink pores, lock water and reduce wrinkles;
Dissolve fat, enhance lymphatic drainage, firm skin and improve skin elasticity.
Press the "COLD handle" on the display to select the COLD output, according to the
It has an anti-geocentric attraction effect on the skin. That is attracting and
customer's,Acceptable level), Then press "start" or press the switch on the treatment head,
outspreading the fibrillar connective tissue of different cortexes through the
the indicator light will light up and start working
rhythmic massage and effectively break down subcutaneous fat and reduce
cellular tissue accumulation of fat. Coupled with the use of the patents
methodology of massaging deeply with roller over different parts of the body
to bring up fat layer in dermis curium and subcutaneous. It releases
micro-vascular lymphatic vessels at the same time promoting metabolism
and converts fat cells in a passive movement to fatty acids. Toxins within the
cells are also eliminated from lymphatic system. In vitro the detoxification
enhances the function as many as four times. The skin will become more
elastic and luster. The perfect "healthy body sculpture management" expert.

EMS muscle stimulator

It is a non-invasive slimming treatment technology that can burn fat while exercising
Just like completing 20,000 sit-ups or squats in just 30 minutes, every 2 to 3 weeks, during
4 to 6 treatments, average fat decreases and muscle mass increases. The treatment
area includes the abdomen, buttocks, arms and thighs.safe and comfortable treatment
Method: Connect the electrode patch (regardless of positive and negative),tie the
electrotherapy patch to the treatment area with a band to adjust the output energy and mode
There are 4 modes, M1, M2, M3, and M4, which are described as follows:
Suction adjustment "M1" works continuously, "M2" works continuously for 2 seconds, and pauses for 2 seconds.
Relax adjustment "M3" works continuously for 1 second and pauses for 1 second. "M4" works continuously for
0.5 seconds and pauses for 0.5 seconds.

Press “VAC RF” in the display screen to select vacuum bipolar RF output,
Set the RF mode : Touch to ajust the RF mode among Auto,M1,M2,M3 modes. Automatic
mode always output, M1 output for 0.5 seconds, M2 output for 1 second, M3 output for 1.5 The wiring is not divided into
seconds,select the suitable intensity (adjust according to the customer's acceptable level, two levels, plus or minus.
It must be inserted to the end,
20%-60%is recommended) and press “START” key to begin operation. Adjust the otherwise the connection
appropriate vacuum suction（Adjust the knob on the back） will be poor.
Method: After applying oil on the skin area to be treated, perform circulatory massage
on specific areas of the skin for about 30 to 40 minutes, which can speed up blood
circulation, It has the function of decomposing fat.

Note:
1.Apply sufficient amount of Oil
2.Keep close contact between the probe and the skin.
3. Adjust the intensity from low level to high level. Matters needing attention:
4.Do not keep the applicator at the same place 1. People who have heart disease and have undergone heart surgery are prohibited from
5. Move the applicator slowly, but constantly. using EMS electrotherapy.
6. Avoid the treatment over bone and do not aim directly to the joint 2. It is forbidden to stick electrotherapy patches around the heart.
7.Always make a skin fold in order to get better access to the fat tissue 3. When the skin is very dry and the conductivity is poor, you can apply some water on
8. In case of resting during treatment, please “PAUSE” and then “STOP” to avoid the skin.Do not exceed 30 minutes each time
over-output of the machine 4. If you feel any uncomfortable feeling after using the product
9. Wipe off the oil inside with alcohol/paper towel after use, then put it on the shelf. Please stop using it immediately and contact your local retailer/distributor.

3 8
 Laser Lipolysis Sextupole body RF handle (RF Body )
Diode Lipo Laser emits low levels of laser energy which creates a chemical signal in the fat
cell,
breaking down the stored triglycerides into free fatty acids and glycerol and releasing them
through channels in the cell membranes. The fatty acids and glycerol are then transported Being integrated with the advanced RF technology, the instrument can directly reach
around the body to the issues that will use them during metabolism to create energy. the deep-seated fat layer with the incisive positioning ability of RF. In the fast-active state,
This process of fatty acid release is a natural response of the body when the body needs fat cell tissue may generate friction heat, increase local temperature and remove excess
to use stored energy reserves, thus it will not create any unnatural reaction in the body fat and toxin from the body through sweat gland, enterohepatic circulation and lymph.
nor does it cause any damage to surrounding structures such as skin, blood vessels and Ultimately achieve the effect of dissolving fat. With controlled depth technology,
peripheral nerves. A period of exercise post treatment will ensure the complete metabolism The effects are very obvious: Enhance blood circulation, accelerate the decomposition of fat,
and thus eliminate from the body the freed fatty acids take away wastes, enhance the effect of removing cellulite, effectively improve the state of
This 5mw lipo laser system can adopt light to penetrate deep level of skin to stimulate areolar tissue, remove stubborn fat .
metabolism for effective slimming treatment. Tied laser board band at the site needing
treatment and use laser for 20 minutes.

Press “BODY RF” in the display screen to select body RF output,

Set the RF mode : Touch to ajust the RF mode among Auto,M1,M2,M3 modes,Automatic
mode always output, M1 output for 0.5 seconds, M2 output for 1 second, M3 output for 1.5
seconds,Spread gel on the treated area evenly.select the suitable intensity
Press “ Laser ” in the display screen to select Laser Lipolysis output, (adjust according to the customer's
Press "-” “+” to adjust the duration of operation. acceptable level, 20%-60%is recommended) and press “START” key to begin operation
Touch to ajust the Laser mode among M1,M2,M3,M4 modes. (drag fat areas at the position for losing weight tothe position where it is closer to the lymph
Clicking "-" to decrease the strength or click “+" to increase it. gland) for about 20 minutes.
Press "START" to start the Laser Lipolysis.
M1, M2, M3, and M4, which are described as follows: Notes:
"M1" works continuously, "M2" works continuously for 0.5 seconds, and pauses for 1. Spread gel on the treated area evenly.
0.5 seconds."M3" works continuously for 0.2 second and pauses for 0.2 second. "M4" 2. Start with low-energy. We suggest to test for the proper energy
works continuously for 0.1 seconds and pauses for 0.1 seconds. level to use on the back of clients before using on the to be treated areas.
3. Do not use essential oil as the medium.
Method : Tied laser board band at the site needing 4. In operation, start pulling only after negative pressure head is attached to skin.
treatment and use laser for 20 minutes, It could quicken the blood 5. Move the applicator slowly, but constantly.
circulation in the treated part of skin and has the effect of decomposing fat. 6.In case of resting during treatment, please “PAUSE” and then “STOP” to avoid
over-output of the machine
Matters needing attention:

1. Please do not radiate eyeball directly with colored light

7 4
 Radio Frequency Handle piece for Face Tripolar eye handle (Tripolar RF)

A capacitive coupling electrode is used for transmitting radio-wave energy and generating an Radio frequency is one kind of high frequency electromagnetic wave, it can penetrate the
electric field for entering into subcutaneous tissue through the skin surface. In the high- dermis and subcutaneous tissue to heat collagen in the dermis layer, collagen in the dermis
frequency to the rapid change in electrode, directions of electrical particles the skin are layer will shrink immediately after the temperature rise and proliferation of new collagen,
also changed. so as to achieve skin rejuvenation and tightening, pigment improvement etc.
By this time, natural electric resistance in the subcutaneous tissue moves and generates gradually eliminate wrinkles , restoring skin elasticity and facial improvement.ate wrinkles
heat energy. As the papillary dermis collagen may immediately shrink when the temperature and prevent skin aging, restoring skin elasticity .
is within the range from 60 to 70 Celsius degree. After wrinkle treatment, client may
immediately sense the skin tightening effects as it is being lifted and firmed.
When collagen is produced continuously, thickness and density of the skin papillary dermis
may be increased to remove wrinkles, eliminate scars, restore skin elasticity and gloss and
make it be blonde and smooth.
While collagen is increased, fresh skin is generated in the position of treatment and
wrinkles are removed in large amount. In addition, when cortex without elasticity or that with
thick horny layer in the area with wrinkles is separated, surrounding skin will also be renewed.

Press “FACE RF” in the display screen to select face RF output, Press “ Eye RF handle” in the display screen to select RF output,
Set the RF mode : Touch to ajust the RF mode among Auto,M1,M2,M3 modes.Automatic Set the RF mode : Touch to ajust the RF mode among Auto,M1,M2,M3 modes,Automatic
mode always output, M1 output for 0.5 seconds, M2 output for 1 second, M3 output for 1.5 mode always output, M1 output for 0.5 seconds, M2 output for 1 second, M3 output for 1.5
seconds, select the suitable intensity (adjust according to the customer's acceptable level, seconds,Spread gel or essence on the treated area evenly.select the suitable intensity
20%-60%is recommended) and press “START” key to begin operation.operate (adjust according to the customer's
with the facial RF head for 15-20 minutes with mainly spiral movement on face acceptable level, 20%-60%is recommended) and press “START” key to begin operation
and around the eyes.

Note: Note:
1.Spread gel or essence on the treated area evenly. 1.Spread gel or essence on the treated area evenly.
2.Keep close contact between the probe and the skin. 2.Keep close contact between the probe and the skin.
3. Adjust the intensity from low level to high level. 3. Adjust the intensity from low level to high level.
4.Do not keep the applicator at the same place 4.Do not keep the applicator at the same place
5. Move the applicator slowly, but constantly. 5. Move the applicator slowly, but constantly.
6.Skin around eyes and forehead is very sensitive, the RF output intensity should 6.Skin around eyes and forehead is very sensitive, the RF output intensity should
be kept relatively low in such areas. be kept relatively low in such areas.
7.In case of resting during treatment, please “PAUSE” and then “STOP” to avoid 7.In case of resting during treatment, please “PAUSE” and then “STOP” to avoid
over-output of the machine over-output of the machine

5 6