Ethernet Switch
Quick Start Guide
1. Description
The products described in this manual, including but not limited to the
illustrated products, please refer to the actual product purchased. If any
changes on product apperance, Please refer to the official product infor-
mation.
2. Packing List
Switch(specific model see the product label for more details)
Power cable(the default is pluggable or a power cable with built-in
power module)
Power adapter(use for some external power products)
Console cable, configurable disc(use for managed products)
Brackets, screw(rack type standard, desktop type optional)
User manual
3. Switch Installation
Switches support a variety of installation methods, desktop, wall mount,
rack mount, please install according to the actual environmental require-
ments.
Mounting Ear Installation
4/8 Port 16/24 Port Wall Mount 1U Rack Mount
Rack Mount Installation
M6 Screw
1 English
4. Connecting Equipment
Network Cable
1. When the RJ45 port is on 2.5GE rate, use Cat5E and above network
cable.
2. When the RJ45 port is on 5GE rate, a shielded network cable of Cat5E
and above specifications is required, the unshielded network cable is not
recommended.
3. When the RJ45 port is on 10GE rate, shielded network cable of Cat6A
and above specifications is required.
Optical Fiber
1. Optical fibers must be used with the optical modules.
2. Fiber bending radius must not be less than 40mm.
Power Cable
1. Distance between power cable and network cable should be more than
10cm.
2. The AC power please use the local AC power cable.
3. The DC power please pay attention to the positive and negative elec-
trodes.
5. Login Management
Thís content is only applicable to managed type of products, please read
this help information for the first application
Web Management
1. Connect the device and PC, to ensure that the device initialization is
complete.
2. Configure the IP address of the PC to be in the same network segment
as the switch default IP address.
3. Enter "http://192.168.2.1" in the address bar of the opened PC browser,
then press "enter" to the web management login interface, input the
default user name "admin" and password "admin", and press "enter".
Console Port Management
1. Connect the PC and the switch console port with the console cable.
2. Start the terminal simulation software, create a connection, select a
serial port, and set communication parameters in consistent with the
default configuration of the switch's console port, as listed below:
Transmission rate: 115200
Dáta bits: 8
Parity bit: None
Stop bits: 1
Flow control mode: None
2 English
6. PoE Powered Function
Thís function is applicable to PoE switches, not applicable to non-PoE
switches
Standard PoE Supply
PoE Switch 1,2/3,6 is the power PoE Camera
supply and data pin
Passive PoE Power Supply
Passive PoE Switch 1,2/3,6 is the data pin Wireless AP
4,5/7,8 is the power pin
1. Standard PoE power supply includes: protocol detection, power pin
sequence detection, power output, abnormal protection, Link abnormal
monitoring.
2. The PoE power supply protocol includes: IEEE802.3af(15.4W),
IEEE802.3at(30W), IEEE802.3bt(90W).
3. The standard PoE power pin sequence is 1,2+/3,6-, and the passive
PoE power pin sequence is 4,5+/7,8-.
4. The standard PoE switches can automatically detect
and supply power to the PDs that meet the standard,
non-PoE devices are not powered and only transmit
data.
5. Passive PoE switches use mandatory power supply
mode, non-PoE powered devices may be burned out,
please use with caution.
6. 24V PoE switches have both low-voltage power
supply and PD detection technology, which can
provide 24V voltage on 4,5/7,8 pin, even if it is
connected to non-standard equipment it will not burn
out.
3 English
7. Indicator Definition
Indicator Definition State Description
PWR Power Indicator Light on / Light off Powered / Abnormal
SYS System Indicator Light on / Flash System Normal / Starting
PoE PoE Indicator Light on / Light off PoE Powered / No Power
1000M Link Rate Light on / Light off Gigabit / 10/100M
100M Link Rate Light on / Light off 100M / Link Disconnect
Link/ACT Link & Data Light on / Flash Link is Normal
Mode/SW Dial Switch Light on/Flash/Off VLAN/Extend/Default
Loop Loop Alarm Light on Port Loop
8. States Definition
Function Definition State Description
VLAN Port Isolation Light on Designated port can not
communicate with each other
Extend Link Extension Flash Designated port link exteded
to 250 meters
Default Normal Mode Light off All ports can communicate
with each other
Reset Reset Button Flash Short press restart, long press
more than 5s reset cofiguration
AI PoE PoE Watchdog / PDs crashed and restart
automatically
MAX Power Display Green PoE power output ≤ 25%
Indicator Yellow PoE power output ≤ 50%
Orange PoE power output ≤ 75%
Red PoE power output ≥ 75%
4 English
