High Pressure Pump

Series HDP MC
Design criteria

Hammelmann high pressure pumps are built to operate at the continuous

maximum duty stated in the performance parameters. Just compare the
crankshaft speed, average plunger speed, plunger diameter and power rating.

High pressure pump

Weight: 11820 lbs

Features
 Power ratings up to 1500 HP
 Vertical 7 cylinder design
 Wide variety of complementary
ancillaries

Quality and reliability

 Stainless steel pump head free of
alternating stress
 Cross head piston bellows seal
 Choice of 'application specific'
seal assemblies
 Solid ceramic or tungsten carbide
plungers
 Choice of bronze or stainless steel
suction chamber
 Crank section calculation by
‘Finite element method’ ensures
long working life under continuous
load
 Twin helical integral reduction
gear with crankshaft supported by
4 bearings
 Pressurised oil lubrication
system with oil cooler/filter

Hammelmann Corp. 436 Southpointe Drive Phone (001) 937-859-8777

Miamisburg, Ohio 45342 Fax: (001) 937-859-9188
eMail: mail@hammelmann.com http://www.hammelmann.com
06/17 © Copyright Hammelmann Maschinenfabrik GmbH, Oelde, Germany. Subject to modification.
HDP MC series, technical data
Performance parameters (Standard design)
Note: Actual flow rates for water as pumped medium
(volumetric efficiency has already been taken into account).
Required power rating [HP]
Q r.p.m.
HDP [GPM]
950 1070 1200 1340 1500 D
Operating pressure [psig] n1 n2
33.3* 43500* 1500 320
38.8* 37000* 41300* 43500* 28 1500/1800 385
47.0* 30500* 34800* 39200* 43500* 1800 460
42.8 32500* 36700* 37700* 1500 320
MC 4

53.1 / 51.5* 27000 30500* 34200* 37700* 32 1500/1800 385

63.4 / 61.5* 22600 25500 28700 31900* 35100* 1800 460
53.9 / 52.3* 26800 31900* 1500 320
63.9 / 62.8* 22500 25400 28300 31900* 35 1500/1800 385
76.0 / 75.2* 18900 21000 23900 26100 30500* 1800 460
*Ultra high pressure
70.5 21000 23200 23900 1500 320
84.5 17400 19600 21800 23900 40 1500/1800 385
 Rod force: 47,210 lbf
MC 3

101.4 14400 16000 18100 20300 22300 1800 460

89.2 16700 18700 19100 1500 320
107.4 13600 15400 17300 19100 45 1500/1800 385
 Stroke: 3.94 inch
128.6 11300 12800 14400 16000 17500 1800 460  Mean piston speed at n2
111.4 13500 15100 15500 1500 320 320 r.p.m. = 3.5 feet/sec
134.1 11000 12500 14100 15500 50 1500/1800 385 385 r.p.m. = 4.2 feet/sec
160.2 9100 10300 11600 12900 14200 1800 460
133.3 11200 12500 12800 1500 320 460 r.p.m. = 5.1 feet/sec
159.7 9100 10300 11600 12800 55 1500/1800 385
191.9 7500 8600 9600 10700 11700 1800 460
158.7 9300 10400 10700 1500 320
190.6 7700 8700 9700 10700 60 1500/1800 385
232.1 6400 7300 8100 9000 9900 1800 460
188.2 8000 9000 9100 1500 320
MC 2

226.0 6500 7400 8300 9100 65 1500/1800 385

275.4 6400 6100 6800 7700 8400 1800 460
218.3 6800 7700 7800 1500 320
262.2 5700 6400 7100 7800 70 1500/1800 385
319.4 4600 5200 5900 6700 7300 1800 460
250.8 5900 6700 6800 1500 320
301.0 4900 5500 6200 6800 75 1500/1800 385
366.4 4100 4600 5200 5800 6200 1800 460
276.4 5200 5900 1500 320
331.6 4200 4800 6400 5900 80 1500/1800 385
404.2 3500 4100 4500 5100 5500 1800 460
276.4 5200 5900 1500 320
331.6 4200 4800 6400 5900 80 1500/1800 385
404.2 3500 4100 4500 5100 5500 1800 460
312.0 4600 5200 6400 1500 320
374.4 3800 4200 4800 6400 85 1500/1800 385 D = Piston/Plunger dia. [mm]
MC 1 High flow

458.6 3200 3500 4100 4500 4900 1800 460 n1 = Motor/Engine r.p.m.
353.5 4100 4600 4800 1500 320 n2 = Crankshaft r.p.m.
424.2 3300 3800 4400 4800 90 1500/1800 385
516.9 2800 3200 3600 4100 4400 1800 460
Conversion table
441.1 3300 3800 1500 320 Rating 1 hp = 0,746 kW
529.3 2800 3000 3500 3800 100 1500/1800 385 Op.pressure 1 psi = 0,069 bar
645.0 2300 2600 2900 3200 3500 1800 460 Flow rate 1 gpm = 0,227 m³/h
539.1 2800 3000 3200 1500 320
647.1 2300 2500 2900 3200 110 1500/1800 385
788.6 1900 2100 2400 2700 2900 1800 460

HDP Seal ** Sealing system ** The dynamic high pressure sealing extends
Dynamic D 28 Tungsten carbide plunger & bushing the advantages of the labyrinth design with
MC4 further increased efficiency.
Dynamic D 35 Tungsten carbide plunger / bronze bushing
Dynamic Ceramic plunger / bronze bushing
MC3
Packing Ceramic plunger / packing
Dynamic D 50 -75 Ceramic plunger / bronze bushing
MC2
Packing D 50 - 80 Ceramik plunger / packing
MC1 Packing Ceramik plunger / packing
HDP 10 High Pressure Pump Series

Hammelmann process pumps are built to operate at continuous maximum

duty. Just compare the crank shaft speed, average plunger speed and
power rating.

High Pressure Pump

Weight: 210 lbs

Features

 Power ratings up to 15 HP
 Vertical 3 cylinder design

Quality and reliability

 Crank section calculation by

‘Finite element method’ ensures
long working life under continuous
load
 Splash lubricated crank section
 Bellows form hermetic seal
between the suction chamber
and crank section
 Stainless steel or bronze suction
chamber
 Solid ceramic or tungsten carbide
Stationary unit plungers
with electric motor  Stainless steel pump head free of
Length: 39 inch alternating stress
Width: 29 inch
Height: 35 inch  Choice of performance and
Weight: approx. 820 lbs pumped medium specific seal and
at 15 HP pump head assemblies
 Flow control achieved with
variable speed gear or frequency
converter
Main dimensions without accessories  Flow turndown ratio 1:10
such as suction line, pressure regulator
etc. All shown as right side drive.
Detailed dimensional drawings and
weights available on request.
HDP 10 series, technical data
Performance parameters
Required power rating [HP]  Rod force: 2,600 lbf
Q r.p.m.
HDP
[GPM]*
7 5,5 10 15 D  Stroke: 1.18 inch
Operating pressure [psig] n1 n2  Mean piston speed at n2
625 r.p.m. = 2.1 feet/sec
0.6 15950 21800 31900 625
0.7 13100 18100 26800 8 750 750 r.p.m. = 2.5 feet/sec
0.8 11200 15200 22500 900
14

1500/1800/2150 900 r.p.m. = 3.0 feet/sec

0.9 10200 13800 20300 625
1.1 8300 11300 16700 10 750
1.3 7100 9800 14200 900

0.9 10200 13800 20300 625

1.1 8300 11300 16700 10 750
1.3 7100 9800 14200 900
13

1500/1800/2150
1.7 6800 9300 13600 625
1.8 5800 8000 11700 12 750
2.1 5100 7000 10300 900

2.4 5000 6100 9100 625

15
2.9 3800 5100 7500 750
3.2 3200 4400 6500 625
17,5
4.0 2800 3600 5500 750
4.2 2500 3400 5100 625
20
5.3 2100 2800 4200 750
6.6 1600 2200 3200 625
25
8.2 1400 1900 2800 750
1500/1800/2150
12

9.8 1100 1500 2200 625

30
11.9 900 1200 1900 750
13.5 800 1100 1700 625
35
16.4 700 900 1400 750
18.0 600 800 1200 625 Hammelmann plunger pumps
40
21.6 500 700 1100 750
convert 93 to 98 % of the shaft
22.7 500 700 1000 625 power to hydraulic energy.
45
27.2 400 500 800 750

Conversion table D = Piston/Plunger dia. [mm]

Rating 1 hp = 0,746 kW n1 = Motor/Engine r.p.m.
Op.pressure 1 psi = 0,069 bar n2 = Crankshaft r.p.m.
Flow rate 1 gpm = 0,227 m³/h

HDP Seal* Sealing system

Dynamic Tungsten carbide plunger & bushing
14
Packing Special ceramic plunger** / packing
Dynamic Ceramic plunger / bronze bushing
13
Packing Ceramic plunger / packing
Dynamic Ceramic plunger / bronze bushing
12
Packing Ceramik plunger / packing

* The dynamic high pressure sealing extends the advantages of

the labyrinth design with further increased efficiency.
** Special ceramic plungers up to max. 2500 bar

Hammelmann Corp. 436 Southpointe Drive Phone (001) 937-859-8777

Miamisburg, Ohio 45342 Fax: (001) 937-859-9188
eMail: mail@hammelmann.com http://www.hammelmann.com
10/13 © Copyright Hammelmann Maschinenfabrik GmbH, Oelde, Germany. Subject to modification.
HDP 20 High Pressure Pump Series
Design criteria

Hammelmann high pressure pumps are built to operate at the

continuous maximum duty stated in the performance parameters.
Just compare the crank shaft speed, average plunger speed,
plunger diameter and power rating.

High Pressure Pump

Weight: 210 lbs Dimensions: inches

Features

 Power ratings up to 25 HP
 Vertical 3 cylinder design
 Wide variety of complementary
ancillaries

Quality and reliability

 Stainless steel pump head free of

alternating stress
 Bellows form hermetic seal
between the suction chamber
Stationary unit and crank section
with electric motor  Choice of application specific seal
assemblies
Length: 39 inch  Solid ceramic or tungsten carbide
Width: 29 inch plungers
Height: 35 inch
 Choice of bronze (standard) or
Weight: approx. 990 lbs
at 29 HP stainless steel suction chamber
 Crank section calculation by ‘Finite
element method’ ensures long
Main dimensions without accessories such as working life under continuous load
suction line, pressure regulator etc. All shown
as right side drive. Detailed dimensional  Pressurised oil lubrication system
drawings and weights available on request.  Separate oil pump

© Copyright Hammelmann Maschinenfabrik GmbH, Oelde, Germany. Technische Änderungen vorbehalten.

Hammelmann Postfach 3309 • D-59282 Oelde Telefon (0 25 22) 76-0

Maschinenfabrik GmbH Zum Sundern 13-21 • Germany Telefax (0 25 22) 76-444
HDP 20 series, technical data
Performance parameters ( Standard design)
Note: Actual flow rates for water as pumped medium
(volumetric efficiency has already been taken into account).
Q
Required power rating [HP]
r.p.m.  Rod force: 3,960 lbf
HDP 15 20 25 D
[GPM]  Stroke: 1.18 inch
Operating pressure [psig] n1 n2
 Mean piston speed at n2
0.6 31900 43500 55100* 625
625 r.p.m. = 2.1 feet/sec
0.7 26800 36300 45000 8 750
0.8 22500 30500 37700 900 750 r.p.m. = 2.5 feet/sec
24

1500/1800/2150
0.9 20300 28300 31900 625 900 r.p.m. = 3.0 feet/sec
1.2 16700 23200 29000 10 750
1.4 14200 18900 23900 900
Typical high pressure
* increased permissible rod force to 4,290 lbf
pump units
0.9 20300 26100 625
1,2 16700 23200 26100 10 750
1.4 14200 18900 26100 900
23

1500/1800/2150
1.6 13600 18100 22500 625
1.8 11700 16000 19600 12 750
2.1 10300 13900 16700 900

2.4 9100 12500 14400 625

15
2.9 7500 10300 12600 750
3.2 6700 9000 10600 625
17,5
4.0 5500 7500 9300 750
4.2 5100 7000 8100 625
20
5.3 4200 5800 7100 750
6.6 3200 4400 5200 625
25
8.2 2800 3600 4500 750  Stationary unit with
22

1500/1800/2150
9.8 2200 3000 3600 625 electric motor
30
12 1890 2600 3200 750
13 1670 2200 2600 625
35
16 1380 1890 2300 750
17 1230 1740 2000 625
40
22 1090 1450 1740 750
22 1020 1380 1600 625
45
27 800 1090 1380 750

Conversion table D = Piston/Plunger dia. [mm]

Rating 1 hp = 0,746 kW n1 = Motor/Engine r.p.m.
Op.pressure 1 psi = 0,069 bar n2 = Crankshaft r.p.m.
Flow rate 1 gpm = 0,227 m³/h
HDP Seal** Sealing system  Stationary electric unit with
Dynamic Tungsten carbide plunger & bushing sound damping cover
24
Packing Special ceramic plunger*** / packing
Dynamic Ceramic plunger / bronze bushing
23
Packing Ceramic plunger / packing
Dynamic Ceramic plunger / bronze bushing Hammelmann plunger pumps
22
Packing Ceramik plunger / packing convert 93 to 98 % of the shaft
** The dynamic high pressure sealing extends the advantages of power to hydraulic energy.
the labyrinth design with further increased efficiency.
*** Special ceramic plungers up to max. 36300 psig.

Hammelmann Corp. 436 Southpointe Drive Phone (001) 937-859-8777

Miamisburg, Ohio 45342 Fax: (001) 937-859-9188
eMail: mail@hammelmann.com http://www.hammelmann.com
06/17 © Copyright Hammelmann GmbH, Oelde, Germany. Subject to modification.
HDP 40 High Pressure Pump Series
Design criteria

Hammelmann high pressure pumps are built to operate at the continuous

maximum duty stated in the performance parameters. Just compare the crank
shaft speed, average plunger speed, plunger diameter and power rating.
High pressure pump
Weight: approx. 440 lbs

Features

 Power ratings up to 50 HP
 Vertical 3 cylinder design
 Wide variety of complementary
ancillaries

Quality and reliability

Dimensions: mm
 Stainless steel pump head free of
alternating stress
 Bellows form hermetic seal between
the suction chamber
and crank section
Stationary unit  Choice of application specific seal
with electric motor assemblies
Length:
Width:
43 inch
32 inch
 Solid ceramic or tungsten carbide
Height: 43 inch plungers
Weight: approx. 1600 lbs  Choice of bronze (standard) or
at 40 HP
stainless steel suction chamber
 Crank section calculation by ‘Finite
Main dimensions without element method’ ensures long
accessories such as suction working life under continuous load
line, pressure regulator etc.
All shown as right side drive.
 Pressurised oil lubrication system
Detailed dimensional drawings
and weights available on
request.
HDP 40 series, technical data
 Rod force: 8,770 lbf
Performance parameters  Stroke: 1.18 inch
Note: Actual flow rates for water as pumped medium  Mean piston speed at n2
(volumetric efficiency has already been taken into account). 625 r.p.m. = 2.1 feet/sec
Required power rating [HP] 750 r.p.m. = 2.5 feet/sec
Q r.p.m.
HDP 20 25 30 40 50 D
[GPM] 900 r.p.m. = 3.0 feet/sec
Operating pressure [psig] n1 n2

1.5 / 1.5* 19600 23900 29700* 40600* 43500* 12 625 Typical high pressure
1.8 / 1.7* 16000 20300 23900 34100* 42100* 12 750

1500 / 1800 / 2150

pump units
2.2 / 1.9* 13500 16700 19600 26800 34800* 12 900
2.2 12500 15400 18100 24700 31900* 15 625
44

2.9 10400 12800 15200 21000 25400 15 750

3.4 8700 10700 12800 17400 21800 15 900
3.3 9100 11300 13500 18100 22500 17,5 625
4.0 7700 9400 11200 15200 18900 17,5 750
4.8 6400 7800 9400 12800 16000 17,5 900
*Ultra high pressure
4.4 7000 8700 10300 14100 17400 20 1500/1800/ 625
43

5.3 5800 7300 8600 11700 14500 20 2150 750

5.3 5800 7100 8600 11600 14200 22 625

6.3 4800 5900 7100 9700 11900 22 750  Stationary unit with
6.3 4800 5900 7100 9700 12000 24 625 diesel motor
7.7 4100 4900 5900 8100 10000 24 750
7.4 4100 5100 6100 8300 10300 26 625
9.0 3500 4200 5100 7000 86000 26 750
1500 / 1800 / 2150

10.0 3000 3800 4500 6200 7700 30 625

11.9 2600 3200 3800 5200 6400 30 750
13.7 2200 2800 3300 4500 5700 35 625
42

16.4 1900 2300 2800 3800 4600 35 750

18.0 1700 2200 2500 3500 4400 40 625
21.6 1500 1800 2100 2900 3600 40 750
22.7 1400 1700 2000 2800 3300 45 625
27.2 1200 1400 1700 2300 2800 45 750
28.2 1100 1400 1600 2200 2800 50 625
33.8 900 1200 1400 1900 2300 50 750
34.1 900 1200 1300 1800 2300 55 625
41.0 700 900 1100 1500 1900 55 750
Conversion table D = Piston/Plunger dia. [mm]
Rating 1 hp = 0,746 kW n1 = Motor/Engine r.p.m.
Op.pressure 1 psi = 0,069 bar n2 = Crankshaft r.p.m.  Stationary unit with
Flow rate 1 gpm = 0,227 m³/h electric motor

HDP Seal ** Sealing system

Dynamic Tungsten carbide plunger & bushing
44
Packing Special ceramic plunger *** / packing
Dynamic Ceramic plunger / bronze bushing
43
Packing Ceramic plunger / packing Hammelmann plunger
Dynamic Ceramic plunger / bronze bushing pumps convert 93 to 98 %
42
Packing Ceramik plunger / packing of the shaft power to
hydraulic energy.
** The dynamic high pressure sealing extends the advantages of
the labyrinth design with further increased efficiency.
*** Special ceramic plungers up to max. 36300 psig.

 Mobile electric unit

with hose reel

Hammelmann Corp. 436 Southpointe Drive Phone (001) 937-859-8777

Miamisburg, Ohio 45342 Fax: (001) 937-859-9188
eMail: mail@hammelmann.com http://www.hammelmann.com
06/17 © Copyright Hammelmann Maschinenfabrik GmbH, Oelde, Germany. Subject to modification.
HDP 70 High Pressure Pump Series
Design criteria

Hammelmann high pressure pumps are built to operate at the continuous

maximum duty stated in the performance parameters. Just compare the crank
shaft speed, average plunger speed, plunger diameter and power rating.

High pressure pump

Weight: approx. 470 lbs
Dimensions: mm

Features

• Power ratings up to 95 HP
• Vertical 3 cylinder design
• Wide variety of complementary
ancillaries

Quality and reliability

• Stainless steel pump head free of

alternating stress
• Choice of application specific seal
assemblies
• Solid ceramic or tungsten carbide
plungers
Stationary unit
with electric motor • Choice of bronze (standard) or
stainless steel suction chamber
Length: 59 inch
Width: 28 inch • Crank section calculation by
Height: 43 inch ‘Finite element method’ ensures
Weight: approx. 521 lbs
at 100 HP
long working life under continuous
load
• Integral speed reduction gear
• Pressurised oil lubrication system
with oil cooler/filter
Main dimensions without accessories
such as suction line, pressure regulator
etc. All shown as right side drive.
Detailed dimensional drawings and
weights available on request.
HDP 70 series, technical data
Performance parameters (Standard design)

Q
Required power rating [HP]
r.p.m. • Rod force: 9,670 lbf
HDP 40 50 60 75 95 D
(GPM)
Operating pressure (psig) n1 n2
• Stroke: 1.57 inch
• Mean piston speed at n2
1.9 / 1.9* 29000* 35500* 43500* 1500 625
2.4 / 2.3* 23900 29700* 36300* 43500* 12 1500/1800 750 625 r.p.m. = 3.3 feet/sec
2.9 / 2.7* 20300 24700 30500* 37000* 43500* 1800/2150 900 750 r.p.m. = 3.9 feet/sec
3.1 / 3.0 18100 22500 27600 34100* 1500 625 900 r.p.m. = 4.7 feet/sec
74

3.8 / 3.6 15200 18900 23200 28300 34800* 15 1500/1800 750

4.5 / 4.3 12900 16000 18900 23200 29700* 1800/2150 900 Typical high pressure
4.5 13500 16700 20300 24700 1500 625
pump units
5.1 11300 14100 16700 20300 25400 17,5 1500/1800 750
6.1 9400 11700 14200 17400 21800 1800/2150 900
*Ultra high pressure
5.5 10300 12800 15200 18900 1500 625
73

20
6.9 8700 10700 13100 16000 19600 1500/1800 750

6.9 8700 10700 13100 16000 16400 1500 625

22
8.4 7300 8800 10900 13200 16400 1500/1800 750
8.4 7300 9000 10900 13300 13800 1500 625
24
10.0 6100 7500 9100 11300 13800 1500/1800 750
10.0 6200 7700 9300 11300 11700 1500 625 • Stationary unit with
26
11.9 5100 6400 7700 9400 11700 1500/1800 750
electric motor
13.2 4600 5700 7000 8600 1500 625
30
15.6 3800 4800 5800 7100 8700 1500/1800 750 1‘ 10 “
18.2 3300 4200 5100 6200 1500 625
35
21.4 2800 3500 4200 5200 6400 1500/1800 750
72

24.0 2600 3200 3900 4800 1500 625

40
28.2 2200 2600 3200 3900 4900 1500/1800 750
30.4 2000 2500 3000 3800 1500 625
45
35.6 1600 2000 2500 3000 3900 1500/1800 750
37.5 1600 1900 2500 3000 1500 625
50
44.1 1300 1600 2000 2500 3000 1500/1800 750
45.4 1300 1600 2000 2500 1500 625
55
53.1 1000 1300 1600 2000 2600 1500/1800 750
• Trolley
D = Piston/Plunger dia. [mm]
n1 = Motor/Engine r.p.m.
n2 = Crankshaft r.p.m.
HDP Seal ** Sealing system Conversion table
Dynamic Tungsten carbide plunger & bushing Rating 1 hp = 0,746 kW
74 Op.pressure 1 psi = 0,069 bar
Packing Special ceramic plunger *** / packing
Flow rate 1 gpm = 0,227 m³/h
Dynamic Ceramic plunger / bronze bushing
73
Packing Ceramic plunger / packing
Dynamic Ceramic plunger / bronze bushing
72
Packing Ceramik plunger / packing

** The dynamic high pressure sealing extends the advantages of

the labyrinth design with further increased efficiency.
*** Special ceramic plungers up to max. 37700 psig.

Hammelmann plunger pumps convert 93 to 98 % • Stationary or road going trailer units

of the shaft power to hydraulic energy. with sound damping cover
• 10 foot sound damped container
versions
Hammelmann Corp. 436 Southpointe Drive Phone (001) 937-859-8777
Miamisburg, Ohio 45342 Fax: (001) 937-859-9188
eMail: mail@hammelmann.com http://www.hammelmann.com
05/18 © Copyright Hammelmann Maschinenfabrik GmbH, Oelde, Germany. Subject to modification.
HDP 140 High Pressure Pump Series
Design criteria

-Hammelmann high pressure pumps are built to operate at the continuous

maximum duty stated in the performance parameters. Just compare the
crankshaft speed, average plunger speed, plunger diameter and power rating.

High pressure pump

Weight: approx. 838 lbs

Features
 Power ratings up to 190 HP
 Vertical 3 cylinder design
 Wide variety of complementary
ancillaries

Quality and reliability

 Crank section calculation by

Stationary unit ‘Finite element method’ ensures
with electric motor long working life under continuous
Length: 76.8 inch load
Width: 33.5 inch
Height: 52 inch  Stainless steel pump head free of
Weight: approx. 3528 lbs alternating stress
at 147 HP
 Integral speed reduction gear
 Pressurised oil lubrication system
with oil cooler/filter
Main dimensions without accessories such
as suction line, pressure regulator etc.  Bellows form hermetic seal
Detailed dimensional drawings and weights between the suction chamber and
available on request.
crank section
 Solid ceramic or tungsten carbide
Stationary unit plungers
with diesel motor  Choice of application specific seal
Length: 82.7 inch assemblies
Width: 51.2 inch
Height: 63 inch  Choice of bronze (standard) or
Weight: approx. 3672 lbs stainless steel suction chamber
at 214 HP without
full fuel tank
 HDP 140 series, technical data
Performance parameters (Standard design)
Note: Actual flow rates for water as pumped medium
(volumetric efficiency has already been taken into account).

Q
Required power rating [HP]
r.p.m.  Rod force: 19,783 lbf
HDP 60 75 100 120 150 190 D
[GPM]
Operating pressure [psi] n1 n2
 Stroke: 2.20 inch
 Mean piston speed at n2
4.0/3.4* 24070 29440* 39880* 46400* 1500 390
4.8/4.2* 20160 24650 33640* 40310* 46400* 17,5 1500/1800 467  390 r.p.m. = 2.36 fee/sec
5.8/5.0* 16680 20450 27840* 33500* 40890* 46400* 1800/2150 560  467 r.p.m. = 2.82 feet/sec
144

5.0/4.8* 18420 22480 30600* 36830* 40600* 1500 390

6.1/5.5* 15370 18850 25670 30890* 37700* 20 1500/1800 467  560 r.p.m. = 3.38 feet/sec
7.1/6.6* 12760 15660 21320 25670 31320* 40600* 1800/2150 560
*Ultra high pressure Typical high pressure
7.9 11750 14360 19580 23490 26100 1500 390 pump units
9.5 9860 12040 16530 19720 24070 25 1500/1800 467
143

11.1 8270 10010 13630 16390 20010 26100 1800/2150 560

9.8 9280 11310 15370 18560 20740 1500 390
11.9 7690 9430 12760 15370 18850 28 1500/1800 467
14.0 6530 7830 10730 12910 15810 20740 1800/2150 560
11.4 8120 10010 13630 16390 17980 1500 390
13.5 6820 8410 11460 13780 16820 30 1500/1800 467
16.1 5660 6960 9430 11460 13920 17980 1800/2150 560
12.9 6960 8560 11750 14070 15810 1500 390
15.3 5950 7250 9860 11890 14500 32 1500/1800 467
18.5 4930 5950 8270 9860 12040 15810 1800/2150 560
15.8 5950 7400 10010 12040 13200 1500 390
18.5 5080 6090 8410 10010 12330 35 1500/1800 467
 Stationary unit with
22.2 4210 5080 6960 8410 10300 13200 1800/2150 560 electric motor
20.6 4640 5660 7690 9140 10150 1500 390
24.6 3920 4790 6380 7690 9430 10150 40 1500/1800 467
29.3 3190 3920 5370 6380 7830 9860 1800/2150 560
26.4 3630 4500 6090 7250 7980 1500 390
31.4 3050 3770 5080 6090 7400 7980 45 1500/1800 467
37.5 2470 3050 4210 5080 6240 7690 1800/2150 560
142

32.7 2900 3630 4930 5950 6530 1500 390

39.1 2470 3050 4060 4930 6090 6530 50 1500/1800 467
46.7 2030 2470 3480 4060 5080 6240 1800/2150 560
39.6 2470 3050 4060 4930 5370 1500 390
47.3 2030 2470 3340 4060 4930 5370 55 1500/1800 467  Road going or stationary
56.5 1740 2030 2760 3340 4210 5080 1800/2150 560 trailer units with sound
46.5 2030 2470 3340 4060 4500 1500 390 damping cover
55.7 1740 2030 2900 3480 4210 4500 60 1500/1800 467
66.5 1450 1740 2320 2900 3480 4350 1800/2150 560
54.6 1740 2030 2900 3480 3920 1500 390
65.5 1450 1740 2320 2900 3480 3920 65 1500/1800 467
78.1 1160 1450 2030 2320 2900 3630 1800/2150 560
63.4 1450 1890 2470 3050 3340 1500 390
75.8 1310 1600 2030 2470 3050 3340 70 1500/1800 467
90.6 1020 1310 1740 2030 2610 3190 1800/2150 560

HDP Seal ** Sealing system D = Piston/Plunger dia. [mm]

Dynamic Tungsten carbide plunger & bushing n1 = Motor/Engine r.p.m.
144 n2 = Crankshaft r.p.m.
Packing Special ceramic plunger *** / packing 10 or 20 foot sound
Dynamic Ceramic plunger / bronze bushing damped container
143 Conversion table versions
Packing Ceramic plunger / packing
Rating 1 hp = 0,746 kW
Dynamic Ceramic plunger / bronze bushing Op.pressure 1 psi = 0,069 bar
142
Packing Ceramik plunger / packing Flow rate 1 gpm = 0,227 m³/h
Hammelmann plunger
** The dynamic high pressure sealing extends the advantages of
pumps convert 93 to
the labyrinth design with further increased efficiency.
*** Special ceramic plungers up to max. 46,400 psi 98 % of the shaft power
to hydraulic energy.
Hammelmann Corp. 436 Southpointe Drive Phone (001) 937-859-8777
Miamisburg, Ohio 45342 Fax: (001) 937-859-9188
eMail: mail@hammelmann.com http://www.hammelmann.com
06/17 © Copyright Hammelmann GmbH, Oelde, Germany. Subject to modification.
 Installations
HDP 146 High pressure
high flow pump

Compact design
 Optimum space utilisation
 Integral reduction gear
Drive end
 Hammelmann standard industrial
drive end specifically designed
Adaptability provides for continuous duty
 Pressurised oil lubrication system
installation options  High quality spheroidal cast iron
housing
 Horizontal or vertical models  Clockwise or anticlockwise
 Reversible pump head rotation
 Central or side suction connection
 Discharge connections on both
sides
 Left or right hand drive shaft Easy servicing
 Can operate at higher inclinations
 Reversible valve seats
 Suction and discharge valves use
identical components
 Maintenance possible without
Water end: suitable for removal of suction and pressure
recycled water lines
 All service access front/above
Less wear due to :  Fixed valve housing accessible
via light weight cover plates
 High grade solid ceramic plungers
 Wear resistant valve seats
 Low flow velocity over suction and
discharge valves Environmentally friendly
 Packing seal sets within rust  Quiet drive end due to twin helical
resistant stainless steel sleeves gears
 Slow plunger speed  Piston rods hermetically sealed by
the NBR bellows, no oil leakage
Technical data [GPM]
Pressure Power required
Piston  n1 [r.p.m.] n2 [r.p.m.]
[psig] [HP]
HDP 146
71.3 3300 150 70 1250/1500/1800 440
 Rod force: 66,420 lbf 85.8 3300 180 70 1500/1800/2150 525
 Stroke: 2.17 in. 94.2 3000 180 70 1650 580

 Mean piston speed at n2 81.6 2900 150 75 1250/1500/1800 440

97.7 2900 180 75 1500/1800/2150 525
440 r.p.m. = 2.7 feet/sec
107.4 2600 180 75 1650 580
525 r.p.m. = 3.1 feet/sec
92.9 2500 150 80 1250/1500/1800 440
580 r.p.m. = 3.5 feet/sec
110.9 2500 180 80 1500/1800/2150 525
122.0 2300 180 80 1650 580
Technical details
Design Horizontal, vertical,
3 cylinder
Plungers Solid ceramic
Plunger sealing Triple packing rings
Crank section sealing Bellows
Valves With ancillary sealing for
recycled water
Valves Reversible
Crank section lubrication Pressurised circulating
Crankshaft bearings 2 x roller
Drive shaft Right or left

Installation data
Weight Approx. 770 lbs
Mounting points 4 x M20
Mounting hole pattern
HDP 146 horizontal 18“ x 11“
HDP 146 vertical 13.5“ x 12“
Drive shaft 2“ dia. x 3.7“
Shaft key DIN 6885 – A
Permissible lateral force 8.850 lbf
Discharge connection G 1 1/4” female
Suction connection 4“ i/d,
PN87 DIN 2 x 3 “

Horizontal design

Vertical design

Hammelmann Corp. 436 Southpointe Drive Phone (001) 937-859-8777

Miamisburg, Ohio 45342 Fax: (001) 937-859-9188
eMail: mail@hammelmann.com http://www.hammelmann.com
5/07 © Copyright Hammelmann Maschinenfabrik GmbH Oelde, Germany. Subject to modification.
HDP 196 High pressure,
high flow pump

Compact design Easy servicing

 Optimum space utilisation  Reversible valve seats
 Light weight Water end: suitable for
 Suction and discharge valves use
 Integral reduction gear recycled water identical components
 Maintenance possible without
Less wear due to : removal of suction and pressure
Adaptability provides
lines
installation options  High grade solid ceramic plungers  All service access from
 Wear resistant valve seats front/above
 Reversible pump head  Low flow velocity over suction and  Fixed valve housing accessible
 Central or side suction connection discharge valves via light weight cover plates
 Discharge connections on both  Packing seal sets within rust
sides resistant stainless steel sleeves
 Operates at any angle  Slow plunger speed Environmentally friendly
 Quiet drive end due to twin helical
Drive end gears
 Hammelmann standard industrial  Piston rods hermetically sealed by
drive end specifically designed the NBR bellows, no oil leakage
for continuous duty
 Pressurised oil lubrication system
 High quality spheroidal cast iron
housing
 Clockwise or anticlockwise
rotation
Technical data
HDP 196
 Rod force: 66,420 lbf Pressure Power required
[GPM] Piston  n1 [r.p.m.] n2 [r.p.m.]
 Stroke: 2.95 in. [psig] [HP]
 Mean piston speed at n2 101.9 3000 200 70 1500/1800 460
460 r.p.m. = 3.7 feet/sec 121.4 3000 240 70 1800/2150 550
550 r.p.m. = 4.5 feet/sec
116.2 2700 200 75 1500/1800 460
141.0 2700 240 75 1800/2150 550
133.3 2300 200 80 1500/1800 460
159.7 2300 240 80 1800/2150 550

Technical details
Design Horizontal, vertical,
3 cylinder
Plungers Solid ceramic
Plunger sealing Triple packing rings
Crank section sealing Bellows
Valves With ancillary sealing for
recycled water
Valves, special feature Reversible
Crank section lubrication Pressurised circulating
Crankshaft bearings 2 x roller
Drive shaft Right

Installation data
Weight incl. lub. oil 1,157 lbs
Mounting hole pattern 14“ x 17“
Drive shaft 2.36“ dia. x 3.7“
Shaft key DIN 6885 – A
Permissible lateral force 11,800 lbf
Discharge connection 1 1/4” female
Suction connection 4“ i/d,
P87 DIN 2631, 2 x 3 “

Horizontal design

Vertical design

6/13 © Copyright Hammelmann Maschinenfabrik GmbH, Oelde, Germany. Subject to modification.

Hammelmann Corp. 436 Southpointe Drive Phone (001) 937-859-8777

Miamisburg, Ohio 45342 Fax: (001) 937-859-9188
eMail: mail@hammelmann.com http://www.hammelmann.com
HDP 200 High Pressure Pump Series
Design criteria

Hammelmann high pressure pumps are built to operate at the continuous

maximum duty stated in the performance parameters. Just compare the
crankshaft speed, average plunger speed, plunger diameter and power rating.

High pressure pump

Weight: approx. 1,157 lbs

Features

 Power ratings up to 270 HP

 Vertical 3 cylinder design
 Wide variety of complementary
ancillaries

Quality and reliability

Stationary unit  Crank section calculation by
with electric motor ‘Finite element method’
Length: 80.2 inch ensures long working life under
Width: 33.5 inch continuous load
Height: 54.3 inch  Stainless steel pump head free
Weight: approx. 4,409 lbs of alternating stress
at 215 HP
 Integral speed reduction gear
Main dimensions without accessories  Pressurised oil lubrication
such as suction line, pressure regulator system with oil cooler/filter
etc. Detailed dimensional drawings and
weights available on request.  Bellows form hermetic seal
between the suction chamber
and crank section
 Solid ceramic or tungsten
Stationary unit carbide plungers
with diesel motor
 Choice of application specific
Length: 100.8 inch seal assemblies
Width: 60.6 inch
Height: 80.7 inch  Choice of bronze (standard) or
Weight: approx. 7,055 lbs stainless steel suction
at 315 HP with chamber
full fuel tank
HDP 200 series, technical data
Performance parameters (Standard design)
Note: Actual flow rates for water as pumped medium
(volumetric efficiency has already been taken into account).
Required power rating [HP]  Rod force: 19,783 lbf
Q r.p.m.
HDP [gpm]
100 120 150 175 215 270 D  Stroke: 2.95 inch
Operating pressure [psig] n1 n2
 Mean piston speed at n2
5.5/5.3* 27550 33350* 41330* 46400* 1500 416 416 r.p.m. = 3.4 feet/sec
6.6/6.1* 22480 27550 34080* 40600* 46400* 17,5 1500/1800 495 495 r.p.m. = 4.1 feet/sec
7.9/7.4* 19580 23200 29000* 34080* 41330* 46400* 1800/2150 593
204

593 r.p.m. = 4.9 feet/sec

7.7/7.4* 21030 25380 30450* 36250* 40600* 1500 416
9/8.7* 17400 21030 25380 31180* 37700* 40600* 20 1500/1800 495
10.8/10.6* 14500 17400 21750 25380 31180* 40600* 1800/2150 593 Typical high pressure
*Ultra high pressure pump units
11.4 13780 16680 19580 23930 26100 1500 416
13.7 11600 14500 16680 19580 23930 26100 25 1500/1800 495
16.4 9430 11600 13780 16680 20300 25380 1800/2150 593
203

14.5 10880 13050 15950 18850 20740 1500 416

17.2 8700 10880 13050 15950 18850 20740 28 1500/1800 495
20.6 7250 8700 10880 13050 15950 20300 1800/2150 593
16.1 9430 11170 13780 16680 17980 1500 416
19.3 7830 9430 11600 13780 16680 17980 30 1500/1800 495
23.0 6530 7980 9430 11600 13780 17400 1800/2150 593
20.6 7540 9140 11170 13490 14940 1500 416
24.3 6380 7690 9430 11310 13780 14940 33 1500/1800 495
29.0 5370 6530 1980 9570 11600 14500 1800/2150 593  Mobile unit with
22.2 6820 8270 10010 12040 13200 1500 416 electric motor
26.4 5800 6960 8410 10150 12330 13200 35 1500/1800 495
31.7 4790 5800 7110 8410 10300 12760 1800/2150 593
29.3 5220 6380 7690 9280 10150 1500 416
34.8 4350 5370 6530 7830 9430 10150 40 1500/1800 495
41.7 3630 4500 5370 6530 7830 10010 1800/2150 593
37.8 4210 5080 6090 7400 7980 1500 416
44.6 3480 4210 5080 6090 7400 7980 45 1500/1800 495
53.3 2900 3480 4350 5220 6240 7830 1800/2150 593
202

47.0 3340 4060 4930 5950 6530 1500 416

55.7 2900 3340 4210 4930 6090 6530 50 1500/1800 495
66.5 2320 2900 3480 4210 5080 6380 1800/2150 593
57.0 2760 3340 4060 4930 5370 1500 416  Road going trailer or
67.1 2320 2760 3480 4060 4930 5370 55 1500/1800 495 stationary units with sound
80.0 2030 2320 2900 3480 4210 5220 1800/2150 593 damping cover
67.1 2320 2760 3480 4060 4500 1500 416
79.2 2030 2320 2900 3480 4210 4500 60 1500/1800 495
94.8 1600 2760 2470 2900 3480 4350 1800/2150 593
78.7 2030 2470 2900 3480 3920 1500 416
93.7 1740 2030 2470 2900 3630 3920 65 1500/1800 495
112.2 1450 1740 2030 2470 3050 3770 1800/2150 593
91.3 1740 2030 2470 3050 3340 1500 416
108.0 1450 1740 2180 2610 3050 3340 70 1500/1800 495
129.1 1160 1450 1740 2180 2610 3190 1800/2150 593
D = Piston/Plunger dia. [mm]
HDP Seal ** Sealing system n1 = Motor/Engine r.p.m.
Dynamic Tungsten carbide plunger & bushing n2 = Crankshaft r.p.m.
174
Packing Special ceramic plunger *** / packing Conversion table
Dynamic Ceramic plunger / bronze bushing Rating 1 hp = 0,746 kW  10 or 20 foot sound damped
173
Packing Ceramic plunger / packing Op.pressure 1 psi = 0,069 bar container versions
Flow rate 1 gpm = 0,227 m³/h
Dynamic Ceramic plunger / bronze bushing
172 Hammelmann plunger
Packing Ceramik plunger / packing
pumps convert 93 to 98 %
** The dynamic high pressure sealing extends the advantages of of the shaft power to
the labyrinth design with further increased efficiency. hydraulic energy.
*** Special ceramic plungers up to max. 43,500 psi
Hammelmann Corp. 436 Southpointe Drive Phone (001) 937-859-8777
Miamisburg, Ohio 45342 Fax: (001) 937-859-9188
eMail: mail@hammelmann.com http://www.hammelmann.com
01/18 © Copyright Hammelmann GmbH, Oelde, Germany. Subject to modification.
HDP 250 L High Pressure Pump series
Design criteria

Hammelmann high pressure pumps

are built to operate at the
continuous maximum duty stated in
the performance parameters. Just
compare the crankshaft speed,
average plunger speed, plunger di-
ameter and power rating.

Features

 Power ratings up to 335 HP

 Horizontal 5 cylinder design
 Wide variety of complementary
ancillaries

Quality and reliability

 Stainless steel pump head free of

alternating stress
 Cross head piston bellows seal
 Choice of application specific seal
assemblies
 Solid ceramic or tungsten carbide
plungers
 Choice of bronze or
stainless steel suction chamber
 Crank section calculation by ‘Fi-
nite element method’ ensures long
working life under continuous load
 Crankshaft supported by 3 bear-
ings and incorporating twin helical
speed reducing gears
 Pressurised oil lubrication system
with oil cooler/filter

High pressure pump

Weight: approx. 2300 lbs

Dimensions: inches
Technical data, series HDP 250 L

Performance parameters
Q
Required power rating [HP]
r.p.m.  Rod force: 18,430 lbf
150 175 215 270 335 D
[GPM]*
Operating pressure [psig] n1 n2  Stroke: 2.95 inch
 Mean piston speed at n2
8.4 26100 32600 39900 43500 1500 390
10.0 21800 26100 32600 41300 43500 17,5 1500/1800 465 390 r.p.m. = 3.2 feet/sec
12.1 18100 21800 26100 34100 43500 1800/2150 555 465 r.p.m. = 3.8 feet/sec
11.1 19600 23900 30500 37700 1500 390 555 r.p.m. = 4.6 feet/sec
13.2 16700 19600 23900 31200 37700 20 1500/1800 465
15.8 19600 24700 32600 1800/2150 555
* At pressures over 29,000 psi approx. 5% of the flow rate is lost due to the compressibility factor of water
17.7 18100 23200 23900 1500 390
21.1 18900 23900 25 1500/1800 465
25.3 19600 1800/2150 555

25.6 8800 10600 12900 16000 16800 1500 390

30.6 7400 8800 10700 13300 16700 30 1500/26000 465
36.7 6100 7400 9000 11200 13900 26000/2150 555
34.8 6500 7800 9400 11700 12300 1500 390
41.7 5400 6500 7800 9900 12300 35 1500/26000 465
49.9 4500 5400 6500 8100 10300 26000/2150 555
45.9 4900 5900 7300 9000 9400 1500 390
54.9 4100 4900 5900 7500 9400 40 1500/26000 465
65.7 3500 4100 4900 6200 7800 26000/2150 555
58.6 3900 4600 5700 7100 7400 1500 390
70.2 3200 3900 4800 5900 7100 45 1500/26000 465
84.2 2800 3200 3900 4900 6200 26000/2150 555 Hammelmann plunger pumps
73.1 3200 3800 4600 5800 6200 1500 390 convert 93 to 98 % of the shaft
87.6 2600 3200 3800 4800 5900 50 1500/26000 465 power to hydraulic energy.
105.1 2200 2600 3200 3900 4900 26000/2150 555
89.5 2600 3000 3800 4800 4900 1500 390
107.2 2200 2600 3200 3900 4900 55 1500/26000 465
128.3 1700 2200 2600 3300 4100 26000/2150 555
104.3 2200 2600 3200 3900 4200 1500 390
124.9 1700 2200 2600 3300 4100 60 1500/26000 465
149.7 1500 1700 2200 2800 3500 26000/2150 555
142.0 1600 1900 2300 2900 3000 1500 390
170.0 1300 1600 1900 2500 3000 70 1500/26000 465
202.2 1000 1300 1500 2000 2500 26000/2150 555

D = Piston/Plunger dia. [mm]

n1 = Motor/Engine r.p.m.
n2 = Crankshaft

Hammelmann Corp. 436 Southpointe Drive Phone (001) 937-859-8777

Miamisburg, Ohio 45342 Fax: (001) 937-859-9188
eMail: mail@hammelmann.com http://www.hammelmann.com
12/10 © Copyright Hammelmann Maschinenfabrik GmbH, Oelde, Germany. Subject to modification.
HDP 300 High Pressure Pump series
Design criteria

Hammelmann high pressure pumps are built to operate at the continuous

maximum duty stated in the performance parameters. Just compare the
crankshaft speed, average plunger speed, plunger diameter and power rating.

High pressure pump

Weight: approx. 2,360 lbs

Features

 Power ratings up to 400 HP

 Vertical 5 cylinder design
 Wide variety of complementary
ancillaries
Quality and reliability
Stationary unit  Power ratings up to 300 kW
with electric motor  Vertical
Crank section calculation
5 cylinder design by
‘Finite element method’ ensures
Length: 101 inch  Wide variety of complementary
long working life under continuous
Width: 50.8 inch ancillaries
load
Height: 56.7 inch
Weight: approx. 7,055 lbs  Stainless steel pump head free of
at 335 HP alternating stress
 Crankshaft supported by 3 bearings
and incorporating twin helical speed
reducing gears
Main dimensions without accessories such  Pressurised oil lubrication
as suction line, pressure regulator etc. All
shown as right side drive. Detailed dimen- system with oil cooler/filter
sional drawings and weights available on  Bellows form hermetic seal
request.
between the suction chamber
and crank section
Stationary unit  Solid ceramic or tungsten
with diesel engine carbide plungers
Length: 120.5 inch  Choice of application specific seal
Width: 61.8 inch assemblies
Height: 102.4 inch  Choice of bronze (standard) or
Weight: approx. 9,921 lbs stainless steel suction chamber
at 422 HP with
full fuel tank
Technical data, series HDP 300
Performance parameters (Standard design)
 Rod force: 88 kN
Note: Actual flow rates for water as pumped medium
(volumetric efficiency has already been taken into account).  Stroke: 3 inch
Required power rating [HP]  Mean piston speed at n2
Q r.p.m.
HDP 150 180 210 270 340 400 D 411 r.p.m. = 3.35 feet/sec
[GPM]
Operating pressure [psi)] n1 n2 493 r.p.m. = 4.0 feet/sec
9.2 / 8.7* 23930 28280 36250* 46400* 1500 411 591 r.p.m. = 4.86 feet/sec
11.1/10.3* 19580 23930 28280 36250* 46400* 17,5 1500/1800 493
13.5/12.4* 16680 19580 23930 33350* 37700* 46400* 1800/2150 591
304

12.1/11.1* 18130 21750 26830 36250 40600* 1500 411 Typical high pressure
14.5/13.5* 15230 18130 21750 27550 34800* 40600* 20 1500/1800 493 pump units
17.4/16.4* 13050 15230 18850 23200 29000* 37700* 1800/2150 591
* Ultra high pressure
18.5 11750 14070 16970 21320 26100 1500 411
22.7 9720 11600 14070 17690 22040 26100 25 1500/1800 493
26.7 8120 9720 11750 14790 18420 23200 1800/2150 591
303

23.2 9280 11170 12040 16970 20740 1500 411

28.2 7690 9280 11310 14070 17550 20740 28 1500/1800 493
33.3 6530 7830 9430 11750 14790 18850 1800/2150 591
26.7 8120 8270 11750 14790 17980 1500 411
32.2 6670 8120 9720 12180 15230 17980 30 1500/1800 493
38.3 5660 8270 8270 10300 12910 15950 1800/2150 591
30.6 7110 8560 10300 12910 15810 1500 411
36.7 5950 7110 8560 10730 13490 15810 32 1500/1800 493  Stationary diesel unit in
43.8 4930 5950 7250 8990 11310 14210 1800/2150 591 BDF-Container with workshop
36.7 5950 7110 8700 10880 13200 1500 411
44.1 4930 5950 7250 8990 11310 13200 35 1500/1800 493
52.8 4210 4930 6090 7540 9430 11600 1800/2150 591
48.8 4500 5510 6670 8270 10150 1500 411
58.3 3770 4500 5510 6820 8560 10150 40 1500/1800 493
69.7 3190 3770 4640 5800 7250 8990 1800/2150 591
62.6 3630 4350 5220 6530 7980 1500 411
74.4 3050 3630 4350 5510 6820 7980 45 1500/1800 493
89.0 2470 3050 3630 4500 5660 6960 1800/2150 591
77.9 2900 3480 4210 5220 6530 1500 411
302

92.9 2470 2900 3480 4350 5510 6530 50 1500/1800 493

111.1 2030 2470 2900 3630 4640 5510 1800/2150 591
94.2 2470 2900 3480 4350 5370 1500 411
112.5 2030 2470 2900 3630 4500 5370 55 1500/1800 493  Stationary electric unit
134.4 1740 2030 2470 3050 3770 4640 1800/2150 591
110.4 2030 2470 2900 3630 4500 1500 411
132.5 1740 2030 2470 3050 3770 4500 60 1500/1800 493
158.4 1450 1740 2030 2610 3190 3920 1800/2150 591
129.6 1740 2030 2470 3190 3920 1500 411
155.5 1450 1740 2030 2610 3190 3770 65 1500/1800 493
185.9 1160 1450 1740 2180 2760 3340 1800/2150 591
150.2 1450 1740 2180 2760 3340 1500 411
180.3 1310 1450 1740 2320 2760 3340 70 1500/1800 493
216.0 1020 1310 1450 1890 2320 2900 1800/2150 591
196.4 1160 1380 1670 2100 2470 1500 411
235.5 940 1160 1380 1740 2180 2470 80 1500/1800 493
282.2 800 940 1160 1450 1810 2180 1800/2150 591
 Electric unit in container
** The dynamic high pressure sealing extends the advantages of the D = Piston/Plunger dia. [mm]
labyrinth design with further increased efficiency. n1 = Motor/Engine r.p.m.
*** Special ceramic plungers up to max. 46,400 psi n2 = Crankshaft

Conversion table Hammelmann plunger

Rating 1 hp = 0,746 kW pumps convert 93 to 98 %
Op.pressure 1 psi = 0,069 bar of the shaft power to
Flow rate 1 gpm = 0,227 m³/h
hydraulic energy.

Hammelmann Corp. 436 Southpointe Drive Phone (001) 937-859-8777

Miamisburg, Ohio 45342 Fax: (001) 937-859-9188
eMail: mail@hammelmann.com http://www.hammelmann.com
06/17 © Copyright Hammelmann GmbH, Oelde, Germany. Subject to modification.
HDP 400-2 High Pressure Pump series
Design criteria

Hammelmann high pressure pumps are built to operate at the continuous

maximum duty stated in the performance parameters. Just compare the
crankshaft speed, average plunger speed, plunger diameter and power rating.

High pressure pump

Weight: approx. 3748 lbs

Features

 Power ratings up to 540 HP

 Vertical 3 cylinder design
 Wide variety of complementary
ancillaries

Quality and reliability

 Crank section calculation by

‘Finite element method’ ensures
Stationary unit long working life under continuous
with diesel engine load
Length: 152.7 inch  Stainless steel pump head free of
Width: 56.7 inch alternating stress
Height: 89.4 inch
Weight: approx. 11795 lbs  Integral speed reduction gear
at 540 HP  Pressurised oil lubrication system
with oil cooler/filter
 Bellows form hermetic seal be-
tween the suction chamber and
Main dimensions without accessories
such as suction line, pressure crank section
regulator etc. All shown as right side  Solid ceramic or tungsten carbide
drive. Detailed dimensional drawings
and weights available on request.
plungers
 Choice of application specific seal
assemblies
Hammelmann Corp.  Choice of bronze (standard) or
436 Southpointe Drive stainless steel suction chamber
Miamisburg, Ohio 45342

Phone (001) 937-859-8777

Fax: (001) 937-859-9188
mail@hammelmann.com
www.hammelmann.com
06/17 © Copyright Hammelmann GmbH Oelde, Germany.
Subject to modification.
Technical data, series HDP 400-2
Performance parameters (Standard design)
Required power rating [HP
Q r. p. m. Note: Actual flow rates for water
HDP 270 340 400 470 540 D
[GPM] as pumped medium
Operating pressure [psig] n1 n2 (volumetric efficiency has al-
11.9* 34800* 43500* 1500 340 ready been taken into account).
14.5* 29000* 36250* 43500* 28 1500/1800 410
17.2* 23930 30450* 36250* 42050* 43500* 1800 490
16.1 / 15.3* 26100 32630* 37700* 1500 340
19.3 / 18.5* 22480 26830 33350* 37700* 32 1500/1800 410
404

23.2 / 22.2* 22480 22480 26830 32630* 37700* 1800 490

19.3 / 18.7* 21750 26830 31900* 1500 340
23.5 / 22.4* 17400 21750 26100 31180* 35 1500/1800 410  Rod force: 47,209 lbf
28.2 / 27.2 14500 18850 21750 26100 29000* 1800 490  Stroke: 3.15 inch
*Ultra high pressure
25.1 16680 20300 24220 1500 340
 Mean piston speed at n2
30.4 13780 16680 20300 24220 40 1500/1800 410 340 r.p.m. = 3.0 feet/sec
11600 14500 17400 20300 23200 1800 490
403

36.2 410 r.p.m. = 3.6 feet/sec

33.0 12330 15230 18850 1500 340
39.6 10150 13050 15230 18130 45 1500/1800 410
490 r.p.m. = 4.3 feet/sec
47.5 8700 10880 13050 15230 17400 1800 490
40.1 10440 12760 15520 1500 340 Typical high pressure
48.3 8700 10880 12760 15230 50 1500/1800 410
57.6 7250 8990 10880 12760 14500 1800 490
pump units
48.6 8560 10730 12760 1500 340
58.6 7110 8850 10440 12470 55 1500/1800 410
70.0 5800 7400 8850 10440 12040 1800 490
58.9 7110 8700 10730 1500 340
71.0 5800 7250 8700 10300 60 1500/1800 410
84.7 4790 6090 7250 8560 9860 1800 490
69.4 5950 7540 9140 1500 340
402

83.7 4930 6240 7540 8700 65 1500/1800 410

100.1 4060 5220 6240 7250 8410 1800 490
80.8 5080 6380 7830 1500 340
97.4 4210 5370 6240 7400 70 1500/1800 410
116.4 3480 4500 5370 6240 7110 1800 490
92.4 4350 5660 6820 1500 340  Diesel unit in container
111.4 3770 4640 5510 6530 75 1500/1800 410
133.1 3050 3920 4640 5510 6240 1800 490
104.5 3920 4930 5950 1500 340
125.9 3190 4060 4930 5800 80 1500/1800 410
150.5 2760 3480 4060 4890 5510 1800 490
104.5 3920 4930 5950 1500 340
125.9 3190 4060 4930 5800 80 1500/1800 410 Hammelmann plunger
150.5 2760 3480 4060 4790 5510 1800 490 pumps convert 93 to 98 %
115.6 3480 4500 5370 1500 340
of the shaft power to hy-
139.4 2900 3770 4500 5220 85 1500/1800 410
166.6 2470 3050 3770 4350 4930 1800 490
draulic energy.
130.9 3190 3920 4790 1500 340
401 High flow

157.9 2610 3190 3920 4640 90 1500/1800 410

188.8 2180 2760 3190 3770 4350 1800 490 D = Piston/Plunger dia. [mm]
162.9 2470 3190 3770 1500 340 n1 = Motor/Engine r.p.m.
196.4 2030 2610 3190 3630 100 1500/1800 410 n2 = Crankshaft
234.7 1740 2180 2610 3050 3480 1800 490
199.6 2030 2610 3190 1500 340
Conversion table
240.8 1740 2175 2470 3050 110 1500/1800 410
Rating 1 hp = 0,746 kW
287.8 1450 1740 2180 2470 2900 1800 490 Op.pressure 1 psi = 0,069 bar
238.4 1740 2180 2610 1500 340 Flow rate 1 gpm = 0,227 m³/h
284.6 1450 1890 2180 2610 120 1500/1800 410
340.3 1310 1600 1890 2180 2470 1800 490

HDP Seal** Sealing system ** The dynamic high pressure sealing extends the ad
Dynamic D 28 Tungsten carbide plunger & bushing vantages of the labyrinth design with further increased
404 efficiency.
Dynamic D 35 Tungsten carbide plunger / bronze bushing
Dynamic Ceramic plunger / bronze bushing
403
Packing Ceramic plunger / packing
Dynamic D 50 -75 Ceramic plunger / bronze bushing
402
Packing D 50 - 80 Ceramic plunger / packing
401 Packing Ceramic plunger / packing
High Pressure Pump Series HDP 500
Design criteria

Hammelmann high pressure pumps are built to operate at the continuous

maximum duty stated in the performance parameters. Just compare the
crankshaft speed, average plunger speed, plunger diameter and power rating.

High pressure pump

Weight: 4.320 lbs

Features

 Power ratings up to 670 HP

 Vertical 3 cylinder design
 Wide variety of complementary
ancillaries

Stationary unit
with electric motor Quality and reliability
Length: 114 inch
Width: 52 inch  Stainless steel pump head free of
Height: 75 inch alternating stress
Weight: approx. 12,348 lbs  Cross head piston bellows seal
at 536 HP  Choice of 'application specific'
seal assemblies
Main dimensions without accessories such
as suction line, pressure regulator etc. All  Solid ceramic or tungsten carbide
shown as right side drive. plungers
Detailed dimensional drawings
 Choice of bronze or stainless
and weights available on request.
steel suction chamber
Stationary unit  Crank section calculation by
with diesel engine ‘Finite element method’ ensures
long working life under continuous
Length: 120 inch load
Width: 66 inch
Height: 94 inch  Crankshaft supported by
2 bearings and incorporating twin
Weight: approx. 14,773 lbs helical speed reducing gears
at 700 HP with
full fuel tank  Pressurised oil lubrication
system with oil cooler/filter

Hammelmann Corp. 436 Southpointe Drive Phone (001) 937-859-8777

Miamisburg, Ohio 45342 Fax: (001) 937-859-9188
eMail: mail@hammelmann.com http://www.hammelmann.com
06/17 © Copyright Hammelmann Maschinenfabrik GmbH, Oelde, Germany. Subject to modification.
HDP 500 series, technical data
Performance parameters (Standard design)  Rod force: 47,200 lbf
Note: Actual flow rates for water as pumped medium  Stroke: 3.94 inch
(volumetric efficiency has already been taken into account). Mean piston speed at n2
Required power rating [HP] 315 r.p.m. = 3.5 feet/sec
Q r.p.m.
HDP 400 470 540 600 670 D
[GPM] 380 r.p.m. = 4.2 feet/sec
Operating pressure [psig] n1 n2
465 r.p.m. = 5.1 feet/sec
13.7* 43500* 1500 315
16.6* 37000* 43500* 28 1500/1800 380 Typical high pressure
20.3* 30500* 35500* 39900* 43500* 1800 465 pump units
18* 32600* 37700* 1500 315
504

22.4/ 21.6* 27100 31600* 36300* 37700* 32 1500/1800 380

27.5 / 26.4* 22200 25800 29700* 33400* 35400* 1800 465
13.7 / 21.9* 26800 31900* 1500 315
26.9 / 26.4* 22500 26100 30500* 31900* 35 1500/1800 380
33.0 / 32.2* 18100 21000 24700 27600 31900* 1800 465
*Ultra high pressure
29.8 20700 24200 1500 315
35.9 17000 19900 22800 24200 40 1500/1800 380
43.8 14200 16500 18900 21300 23600 1800 465
503

37.0 16400 19100 1500 315

44.6 13500 15700 18000 19100 45 1500/1800 380
54.1 11200 13100 14900 16800 18700 1800 465
 Stationary unit with
46.2 13300 15500 1500 315 diesel motor
55.4 10900 12800 14500 15500 50 1500/1800 380
67.6 9000 10600 12000 13600 15100 1800 465
56.5 11000 12800 1500 315
67.8 9000 10400 12000 12800 55 1500/1800 380
82.6 7500 8700 10000 11200 12500 1800 465
68.1 9300 10700 1500 315
81.6 7500 8800 10000 10700 60 1500/1800 380
99.5 6200 7400 8400 9400 10400 1800 465
80.8 7800 9100 1500 315
502

96.9 6400 7500 8600 9100 65 1500/1800 380

118.0 5400 6200 7100 8000 9000 1800 465
93.5 6800 7800 1500 315
112.2 5500 6500 7400 7800 70 1500/1800 380
136.8 4600 5400 6100 7000 7700 1800 465  Stationary unit with
107.4 5900 6800 1500 315 electric motor
128.8 4800 5700 6400 6800 75 1500/1800 380
157.1 4100 4600 5400 6100 6700 1800 465
118.6 5200 5900 1500 315
142.0 4200 4900 5700 5900 80 1500/1800 380
173.2 3500 4100 4600 5400 5900 1800 465
118.6 5200 5900 1500 315
142.0 4200 4900 5700 5900 80 1500/1800 380
173.2 3500 4100 4600 5400 5900 1800 465 Hammelmann plunger pumps
133.8 4600 5400 1500 315 convert 93 to 98 % of the shaft
160.5 3800 4500 5100 5400 85 1500/1800 380 power to hydraulic energy.
195.6 3200 3600 4200 4600 5200 1800 465
501 High flow

151.5 4100 4800 1500 315

181.9 3300 3900 4500 4800 90 1500/1800 380 D = Piston/Plunger dia. [mm]
221.5 2800 3200 3800 4200 4600 1800 465 n1 = Motor/Engine r.p.m. [1/min]
187.2 3300 3800 1500 315 n2 = Crankshaft r.p.m. [1/min]
Conversion table
224.4 2800 3200 3600 3800 100 1500/1800 380 Rating 1 hp = 0,746 kW
273.5 2200 2600 3000 3300 3800 1800 465 Op.pressure 1 psi = 0,069 bar
231.0 2800 3200 1500 315 Flow rate 1 gpm = 0,227 m³/h
277.2 2200 2600 2900 3200 110 1500/1800 380
337.9 1900 2200 2500 2800 3000 1800 465
HDP Seal** Sealing system ** The dynamic high pressure sealing
Dynamic D 28 Tungsten carbide plunger & bushing extends the advantages of the labyrinth
504 design with further increased efficiency.
Dynamic D 35 Tungsten carbide plunger / bronze bushing
Dynamic Ceramic plunger / bronze bushing
503
Packing Ceramic plunger / packing
Dynamic D 50 -75 Ceramic plunger / bronze bushing
502
Packing D 50 - 80 Ceramik plunger / packing
501 Packing Ceramik plunger / packing
High Pressure Pump
Series HDP 800
Design criteria

Hammelmann high pressure pumps

are built to operate at the continuous
maximum duty stated in the
performance parameters. Just
compare the crankshaft speed,
average plunger speed, plunger
diameter and power rating.

High pressure pump

Weight: approx. 8,170 lbs

Features

 Power ratings up to 1070 HP

 Vertical 5 cylinder design
 Wide variety of complementary
ancillaries

Quality and reliability

 Stainless steel pump head free of

alternating stress
 Cross head piston bellows seal
 Choice of 'application specific'
Stationary unit
seal assemblies
with diesel engine
Length: 156 inch  Solid ceramic or tungsten carbide
Width: 83 inch plungers
Height: 87 inch
Weight: approx. 20,300 lbs
 Choice of bronze or stainless steel
at 1100 HP and suction chamber
without full fuel tank  Crank section calculation by
‘Finite element method’ ensures
long working life under continuous
load
Main dimensions without accessories
such as suction line, pressure regulator  Twin helical integral reduction
etc. All shown as right side drive. gear with crankshaft supported
Detailed dimensional drawings and by 4 bearings
weights available on request.
 Pressurised oil lubrication
system with oil cooler/filter

Hammelmann Corp. 436 Southpointe Drive Phone (001) 937-859-8777

Miamisburg, Ohio 45342 Fax: (001) 937-859-9188
eMail: mail@hammelmann.com http://www.hammelmann.com
06/17 © Copyright Hammelmann Maschinenfabrik GmbH, Oelde, Germany. Subject to modification.
HDP 800 series, technical data
Performance parameters (Standard design)
Note: Actual flow rates for water as pumped medium  Rod force: 47,200 lbf
(volumetric efficiency has already been taken into account).
 Stroke: 3.94 inch
Q
Required power rating [HP]
r.p.m.  Mean piston speed at n2
HDP 670 750 840 950 1070 D
[lGPM] 315 r.p.m. = 3.5 feet/sec
Operating pressure [psig] n1 n2
23.0 43500* 1500 315 380 r.p.m. = 4.2 feet/sec
27.7 36300* 40600* 43500* 28 1500/1800 380 465 r.p.m. = 5.1 feet/sec
34.1 30500* 34100* 37700* 42100* 43500* 1800 465
130.1* 32600* 36500* 1500 315
Typical high pressure
804

37.5 / 36.2* 27000 30200* 34100* 37700* 32 1500/1800 380

45.7 / 44.4* 22000 24700 27800 31200* 35400* 1800 465
pump units
37.2 / 36.7* 26800 31200* 31900* 1500 315
44.9 / 43.8* 21800 24700 28300 31900* 35 1500/1800 380
54.9 / 53.6* 18100 20300 23200 26100 30500* 1800 465
* Ultra high pressure
49.9 20700 23200 24200 1500 315
59.9 17100 19100 21500 24200 40 1500/1800 380
72.9 14200 16000 17800 20200 22800 1800 465
803

61.8 16400 17700 19100 1500 315

74.2 13500 15100 17000 19100 45 1500/1800 380
90.3 11200 12600 14100 16000 18000 1800 465
77.1 13300 14900 15500 1500 315
92.4 10900 12200 13800 15500 50 1500/1800 380  Stationary unit with
112.7 9100 10200 11500 12900 14500 1800 465 diesel motor
94.2 11000 12300 12800 1500 315
113.3 9000 10200 11300 12800 55 1500/1800 380
137.8 7500 8400 9400 10600 12000 1800 465
113.5 9300 10300 10700 1500 315
136.2 7500 8400 9600 10700 60 1500/1800 380
165.8 6200 7100 8000 9000 10000 1800 465
134.4 7800 8800 9100 1500 315
802

161.3 6400 7300 8100 9100 65 1500/1800 380  Diesel unit in container
196.7 5400 6000 6800 7700 8600 1800 465 with workshop
156.0 6800 7500 7800 1500 315
187.2 5500 6200 7000 7800 70 1500/1800 380
228.1 4600 5200 5800 6500 7400 1800 465
178.2 5900 6400 6800 1500 315
214.9 4800 5400 6100 6800 75 1500/1800 380
261.9 280 4500 5100 5700 6400 1800 465
197.5 5200 5800 5900 1500 315
236.8 4200 4800 5400 5900 80 1500/1800 380
288.8 3500 3900 4500 5100 5700 1800 465
197.5 5200 5800 5900 1500 315
236.8 4200 4800 5400 5900 80 1500/1800 380
288.8 3500 3900 4500 5100 5700 1800 465
 Stationary unit with
236.8 4500 5100 5400 1500 315 electric motor
267.4 3800 4200 4800 5400 85 1500/1800 380
801 High flow

327.6 3000 3500 3900 4500 4900 1800 465

252.6 4100 4500 4800 1500 315
303.1 3300 3800 4200 4800 90 1500/1800 380
369.3 2800 3000 3500 3900 4500 1800 465
315.0 3300 3600 3800 1500 315 Hammelmann plunger pumps
378.0 2800 3000 3300 3800 100 1500/1800 380 convert 93 to 98 % of the shaft
460.7 2200 2500 2800 3200 3600 1800 465 power to hydraulic energy.
385.2 2800 3000 3200 1500 315
462.3 2200 2500 2800 3200 110 1500/1800 380
Conversion table
563.1 1900 2000 2300 2600 2900 1800 465 Rating 1 hp = 0,746 kW
D = Piston/Plunger dia. [mm] Op.pressure 1 psi = 0,069 bar
HDP Seal** Sealing system
n1 = Motor/Engine r.p.m. [1/min] Flow rate 1 gpm = 0,227 m³/h
Dynamic D 28 Tungsten carbide plunger & bushing n2 = Crankshaft r.p.m.[1/min]
804
Dynamic D 35 Tungsten carbide plunger / bronze bushing
** The dynamic high pressure sealing extends the
Dynamic Ceramic plunger / bronze bushing advantages of the labyrinth design with further
803
Packing Ceramic plunger / packing increased efficiency.
Dynamic D 50 -75 Ceramic plunger / bronze bushing
802
Packing D 50 - 80 Ceramic plunger / packing
801 Packing Ceramic plunger / packing