SM-2572
Cylinder
Bluetooth®
Speaker
Instruction Manual
Whats Included:
• 1 x Cylinder Bluetooth® Speaker
• 1 x USB to Micro-USB Charging Cable
LED Indicator: Tech Specifications:
1. Charging: Glowing Red LED 1. Pairing Name: “Cylinder Speaker”
2. Charging Complete: Red LED off 2. Battery capacity: 300mAh
3. Listening Time (at max vol): 1 hour
4. Charging Time: 1.5 hours
Instructions:
(Be sure to fully charge the speaker before using for the first time)
1. Charging the Speaker:
• Connect the provided Micro-USB charging cable to a power source and
to the Micro-USB input port on the speaker.
• The LED indicator will glow RED when charging, and will turn OFF when
fully charged.
2. Bluetooth® Setup:
• Turn ON the power switch
• Once on, the speaker will enter Bluetooth pairing mode.
• Using a Bluetooth enabled device, search for “Cylinder Speaker” from
the list of available options.
3. Using the Speaker:
• Use the audio device to control track selection and volume
Note: In order to charge device use only accessory cable (provided with
** device) or the cable included with your own device by the manufacturer.
Safety Precautions: FCC Radiation
WARNING-When using this product, basic
precautions should always be followed:
Exposure Statement:
1. Read all the instructions before use.
2. Charge the speaker completely before initial use The device has been evaluated to meet general RF
for best practices. exposure requirement. The device can be used in
3. If the device does not respond once it is powered portable exposure condition without restriction.
on, the battery capacity may be low.
IC Statement:
4. Do not over charge the internal battery.
5. Do not immerse into water or expose it to moisture
or weather conditions.
6. Do not drop, knock, or shake. Rough handling can
damage the internal precision component and its • This device contains licence-exempt transmitter
boards. (s)/receiver(s) that comply with Innovation,
7. Keep away from children, this device is not a toy. Science and Economic Development Canada’s
8. Keep away from fire or other sources of heat. licence-exempt RSS(s). Operation is subject to
9. Expose to high temperatures may cause it to the following two conditions:
explode. 1. (1) This device may not cause interference.
2. (2) This device must accept any interference,
10. Do not short-circuit, as this may cause damage to including interference that may cause undesired
the unit. operation of the device.
11. Unauthorized change or modifications may void L’émetteur/récepteur exempt de licence contenu
your right to use this product. dans le présent appareil est conforme aux CNR
While using, always comply with any special d’Innovation, Sciences et Développement
regulations that may apply to the area you are in économique Canada applicables aux appareils
and always turn off your mobile device when its radio exempts de licence. L’exploitation est
use is prohibited. autorisée aux deux conditions suivantes :
1. (1) L’ appareil ne doit pas produire de brouillage;
2. (2) L’ appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est
susceptible d’ en compromettre le
FCC Statement: fonctionnement.
Radio Frequency Exposure Statement for IC:
This equipment complies with IC exposure limits
set forth for an uncontrolled environment. This
This device complies with Part 15 of the equipment can be used in portable exposure
FCC Rules. Operation is subject to the conditions.
following two conditions: Déclaration d’exposition aux radiofréquences
1. This device may not cause harmful pour IC:
interference, and Cet équipement est conforme aux limites
2. This device must accept any interference d’exposition IC établies pour un environnement
received, including interference that may non contrôlé. Cet équipement peut être utilisé
cause undesired operation. dans des conditions d’exposition portables.
Warning:
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s authority
to operate the equipment.
Note:
This equipment has been tested and found to comply
with the limits for a Class B digital device pursuant to
part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a Name of the Distributor:
particular installation. If this equipment does cause Bulletline Inc
harmful interference to radio or television reception, Address of the Distributor:
which can be determined by turning the equipment
the interference by one or more of the following 6301 East 10th Avenue, Suite 110
measures: Hialeah, FL 33013 USA.
Reorient or relocate the receiving antenna. Model #: S10
- Increase the separation between the equipment
and receiver. IC: 32527-257206
- Connect the equipment into an outlet on a circuit FCC ID: 2AYIY-S10
different from that to which the receiver is connected. Made in China
- Consult the dealer or an experienced radio/TV
technician for help.
