ry

Module : disk,PCILib,do,dowin,ePSA
Authors : marky, shuangw
Test #1 : Run disk -conf
Expect : Verify Slot numbers for M.2 devices are 1..20 as correct for the card and
the Bay is the PCI Slot # (UT and PT board)
Test #2 : Run do/dowin cdump and pcie(.exe and Configuration [ PCIe ])
Expect : Verify Wrigley only detected for new ID's 10B5.8796.1120.8796 (not UT
board 10B5.8796.10B5.8796)

Issue : Add hddbv Ver 05 for W: drive to be mapped in some cases that require a
more complicated /user:{name}
Change : 33334
System : All
Impact : Factory only
Module : dowin/Dellmech
Authors : marky
Test #1 : Run hddbv.bat in factory where Z and W drives mapped using more
complicated /User:{name}
Expect : Script works fine

Issue : ECR138968 on Centauri X Area 51 R7 with Colfax CPU : request release new
EPSA with CPU temperature alert at 115 C for Colfax CPU based system ID 0x0901
Change : 33302
System : Centauri X R7 with Colfax CPU
Impact : Factory, Customer
Module : EPSA System Health, Thermal Sensor processing
Authors : carl
Test #1 : run Sysman.exe or SystemManagement.exe
Expect : Thermal warnings only if CPU temperature is 115 degrees C or higher

Issue : Add Glist test to end of DEFT and DSTLong tests as engineering expected
: Remove ability for disk.exe to DISABLE SMART accidentally. I don't think
it ever did but it tried to restore to DISABLED if found that way
: Add Commodity type nvme_m2_consumer_upa for NH(Neptune Harbor) inside
Teton Glacier P/N 19RWR, YDH3V, 7HHTM
: Add Commodity type nvme_m2_upa_aux for SB2(Stony Bridge 2) also inside
Teton Glacier P/N 19RWR, YDH3V, 7HHTM
Change : 33265
System : All
Impact : Factory, Customer
Module : Disk,do,dowin
Authors : marky
Test #1 : Disk -f:8 and -f:13 (and also -f:23 or -f:25)
Expect : Verify DST Long is followed by a Glist test (and also for DEFT tests,
too)
Test #2 : Disk -conf -o:testGlacier.txt
Expect : Verify Teton Glacier SB2 part is reported as nvme_m2_upa_aux and NH part
as nvme_m2_consumer_upa

Issue : Add support for multiple dx args

Change : 33262
System : All
Impact : Factory, Customer
Module : Disk
Authors : marky
Test #1 : disk cmd line used on APOS NGM to exclude the RAID1 drives
Expect : Verify the RAID1 HDD:0 and HDD:0 are excluded from testing
Issue : FE033659 HorizonXD had Model = 0 x Empty for split front backplane
Change : 33107
System : HorizonXD (DSS)
Impact : Factory, Customer
Module : Disk
Authors : marky, toddb
Test #1 : disk -conf
Expect : Verify split backplane does not display 0 x Empty

Issue : Add support for Wrigley in PCIe.exe/ePSA and increase array storage for
do/dowin
Change : 33015
System : All (TrailBreaker2)
Impact : Factory, Customer
Module : PCIe
Authors : marky
Test #1 : pcie.exe -?
Expect : Verify help describes the "Slot" formats printed
Test #2 : pcie -util:1 -o:pcie.txt
: Run ePSA PCIe device test
Expect : Verify Wrigley Slots print as PCI4(4,6,7) and the storage slot on the
card
Test #3 : do/dowin bios irq
Expect : Verify all the Wrigley NVMe devices are printed

Issue : FE033459 [ADC LAB PS3] CHANGE REQUEST for 14G PIONEER,R640,DSS, P-41001

Change : 33005
System : Pioneer (DSS)
Impact : Factory, Customer
Module : Disk
Authors : marky
Test #1 : disk -conf -xml -o:disk.xml
: hddbv disk.xml
Expect : Verify P/N 5DH84 is reported HHHL in PCI Slots 2 and 3

Issue : FE033684 -FICORE will append list of Ports and slots to a single string
if there are multiple Arrays with the same serial number
Change : 32991
System : All
Impact : Factory, Customer
Module : disk
Authors : ymb
Test #1 : Run disk -ficore
Expect : Arrays with same serial number need to be appended to a single slot and
port string

Issue : BITS385398 WBDD 6xxx.x [Angelfish] The 3rd network card can't be detected
during PCI buildverify test.
Change : 32805
System : ANGELFISH
Impact : Factory only
Module : SystemConfig
Authors : marky
Test #1 : systemconfig -noexe -xml -o:pci.xml
Expect : Verify P/N's and are reported as <AddInDevice>YES</AddInDevice>

Issue : FE032708 Exception on Sojourner NGM system with 91 HDD's (extra minor
fix)
Change : 32719,32720
System : All
Impact : Factory, Customer
Module : disk
Authors : marky
Test #1 : Run disk -conf and various tests
Expect : Verify no changes and all tests pass. This FE is already fixed but this
updates storelibir-3.dll from 15.02 to 15.11
: to fixe a much rarer failure for NGM configs which might take 157 loops
in s:testperc.bat on a large NGM config

Issue : Coverity. Ensure idrac reset time counter is initialized to 0.

: Coverity. Ensure target buffer has space to add terminator after copy of
unterminated unicode string.
: Coverity. Fix Intelaccess select bits for -details display.
Change : 32505, 32517, 32683
System : Servers
Impact : Factory, Customer
Module : ipmilib, cables
Authors : rods
Test #1 : run modules
Expect : Correct operation.

Issue : Merge for the Converged Diagnostics

Change : 32488
System : All
Impact : Factory, Customer
Module : All
Authors : carl
Test #1 : run module
Expect : Correct operation.

Issue : FixInt - function and variable renaming and new/clarifying comments.

Change : 32405, 32464
System : All
Impact : Factory only
Module : disk
Authors : ymb
Test #1 : Run disk -conf
Expect : No changes to output

Issue : BITS383089 Add support Vancouver USB-based SATA drive via mdiag-
controlled USBHDD.INI
Change : 32290
System : Vancouver
Impact : Factory only
Module : disk
Authors : marky, toddb
Test #1 : Run disk -conf -usbhdd:.
Expect : Verify SATA drive P/N VCWP1 reports Commodity = hard_drive(m2_ssd) and
Width = M.2 with usbhdd.ini containing:
[USBHDD]
# Model: {String}, Commodity: {String}, Width: {String} # Comments
Model: 1100 SATA 1024GB, Commodity: m2_ssd, Width: M.2 # P/N VCWP1 BITS383089
# Mdiags to provide additional lines as needed here for Vancouver

Issue : Add support for new Microchip (PMC/Adaptec) SmartRAID HBA (Darwin)
Change : 32285
System : Horizon
Impact : Customer, Factory
Module : disk
Authors : ymb
Test #1 : Run disk -conf
Expect : Verify information is correct, especially slots, controllers, bays and
PCIIDs
Test #s : Run all disk tests : -f:3, -f:7, -f:23
Expect : Verify drives successfully complete tests, specifically SATA drives not
all failing SMART commands.

Issue : Add support for Wrigley P/N K8MV4

Change : 32249
System : C4140
Impact : Customer, Factory
Module : disk,PCILib
Authors : marky, toddb, shuangw
Test #1 : Run disk -conf
Expect : Verify Slot numbers for M.2 devices are 1..20 as correct for the card and
the Bay is the PCI SLot #

6105.2
-----------------------------------------------------------------------------------
----------------------------------
Issue : FE033520 / FE033429 Stash Sled numbers incorrect when compute sled PERC
added
Change : 32173
System : Odyssey with Stash
Impact : Customer, Factory
Module : disk
Authors : marky, toddb
Test #1 : Run disk -conf
Expect : Verify stash sled numbers are correct and FD33x controllers have
BusDeviceFunction value

Issue : Change 22520 does not work for STARK to assign Commodity (nvme_m2) to M.2
drives and "WIDTH=??" M.2 or 2500
Change : 32165
System : Stark family
Impact : Customer, Factory
Module : disk
Authors : marky, toddb
Test #1 : Run disk -conf
Expect : Verify M.2 show up as Width = M.2 for PCI cards in PCI Slot 5 and 1

Issue : Updated signed dddriver which would work on full OS

Change : 32163
System : All
Impact : Customer, Factory
Module : dddriver
Authors : peter, shuangw
Test #1 : N/A

Issue : CR: BITS383533 WBDD SIL enhancement to add CPU PPIN to XML output
Change : 32110
System : All
Impact : Factory
Module : SystemConfig
Author : bradw
Test : run SystemConfig -sil
Expect : Processor serial number will be N/A or 16 hex digits

Issue : FE033309 FE033401, FE033440, FE033453 Various issues with PERC logical
drives failing -f:2, etc
Change : 32050, (TFS1: 22632, 22633)
System : All
Impact : Customer, Factory
Module : disk
Authors : marky, toddb
Test #1 : Run disk -f:2 on a PERC with two logical drives
Expect : Verify no exception occurs

6105.1
-----------------------------------------------------------------------------------
----------------------------------
Issue : Add full OS compatible signed dddriver.sys
Change : 32009
System : All
Impact : Customer, Factory
Module : dddriver
Authors : shuangw, peter
Test #1 : run WBDD on full OS
Expect : dddriver can be loaded successfully

Issue : New. Drop support for client DEH log.

Change : 31995
System : All
Impact : Customer, Factory
Module : eventlog library, eventlog, memory
Authors : rods
Test #1 : Run "memory" or "eventlog"
Expect : Should be no DEH events. Modules should pass on WSMT-enabled system.

Issue : FE032708 Workaround bug in IR3 15.02 DLL to fix exception

Change : 31993
System : Servers
Impact : Factory, Customer
Module : disk
Authors : marky, yvette
Test #1 : s:loop 1000 fixIR3.txt call diskv.bat diskv.txt . 1 percLog
Expect : Verify test loops and does not fail on NGM system with 95 drives in 6
sleds

Issue : Add automatic HHHL support, initially for P/N R70WT DSS P4608 HHHL, but
also for any future HHHL
Change : 31946,31979
System : Servers
Impact : Factory, Customer
Module : disk
Authors : marky, toddb
Test #1 : disk -conf
Expect : Verify HHHL cards (NVMe drives and PCIe Bridge) report WIDTH = HHHL
Expect : Verify all disk ctlrs (not just some) have BusDeviceFunction = BB:DD:F
information

Issue : Fixed build error of potentially uninitialized local variable

'clientResponse' used
Change : 31935
System : All
Impact : None
Module : Exec
Authors : shuangw
Test #1 : N/A

Issue : New. Allow eventlog.exe to set the eventlog library to special mode for
internal testing.
Change : 31910
System : All IPMI
Impact : None - internal use only
Module : Eventlog, eventlog library
Authors : rods
Test #1 : N/A

Issue : fATAGetDellPage and fATAGetHddPpid calls PMC functions for ATA drives on
Adaptec/PMC/Microsemi/Microchip controllers
Change : 31830
System : Servers
Impact : Factory, Customer
Module : disk
Authors : ymb
Test #1 : disk -conf
Expect : output includes PPID on ATA drives connected to Adaptec / PMC controllers

Issue : BITS381849 Run DDUsbDiag.exe test fail in WBDD for VID:PID of 0C45:6720
Change : 31838
System : Bandon 13, North Bay 13
Impact : Factory
Module : DDUsbDiag
Authors : carl
Test #1 : ddusbdiag.exe
Expect : Driver to load for the camera module with VID:PID of 0C45:6720 and run
the UBIST tests for the camera.

Issue : New. Add Front HDD Bay Intrusion to Cables for Spitzer
Change : 31823
System : Spitzer
Impact : Customer, Factory
Module : cables
Authors : rods
Test #1 : cables -conf
Expect : Verify Front HDD Bay intrusion signal is present and correct

Issue : Fix disk infinite loop on some configs only, in TFS2 port
Change : 31795
System : All
Impact : Customer, Factory
Module : disk
Authors : marky
Test #1 : disk -conf
Expect : Verify no hang occurs

Issue : Fix WBDD errorcodes to match documentation\Window Diags\ADDF FrameWork\

Windows Diagnostic User Guide.doc
Change : 31793
System : All
Impact : Customer, Factory
Module : cExec
Authors : marky
Test #1 : pcie -util:1
Expect : Verify training error (on bad system or forced by code) is hex 6870 not
E190 (E190 = ePSA 8170 | 4000 | 6800)

Issue : Add df batch to show all the drive letters, including USB
Change : 31724,31775
System : All
Impact : Factory only
Module : dowin/Dellmech
Authors : marky
Test #1 : df and help
Expect : Verify help lists df and, also verify df prints all the drive letters
(that exist)

Issue : FE033309 disk output invalid format (missing BackplaneNumber in -conf for
BP0)
Change : 22587
System : All
Impact : Customer, Factory
Module : disk
Authors : marky
Test #1 : Run disk -conf on SAS9311 disk ctlr
Expect : Verify BackplaneNumber is 1 (not a missing line) in -conf for BP:0

Issue : Add hddbv Ver 0.4 support for w: drive to be mapped as y:

Change : 22582,22587
System : All
Impact : Factory only
Module : dowin/Dellmech
Authors : marky
Test #1 : Run hddbv.bat in factory where files are mapped on Y: drive, not W:
Expect : Script works fine

6104.5
-----------------------------------------------------------------------------------
----------------------------------

Issue : "Dell FD33xS HBA" and "Dell FD33xD HBA" hang -f:2 in 6104.4
Change : 22567
System : STASH
Impact : Customer, Factory
Module : disk
Authors : marky, yvette
Test #1 : disk -f:2
Expect : Verify test does not hang for no apparent reason

Issue : BITS373635. Fixed DDDriver and ADDF\Video to support 64 bit physical

address.
: Fixed memory scan test code, so that the correct test pattern is returned
to the caller function.
: (test pattern is all 0's or all F's for video.exe memory scan test)
Change : 22557, 22564
System : LaFerrari XPS
Impact : Customer, Factory
Module : video, dddriver, (memory - affects video memory test, but not the
memory.exe)
Authors : shuangw, brad, marky
Test #1 : run video.exe on LaFerrari XPS or LaFerrari Precision
Expect : Verify the video test passes
Issue : FE033291 Gets exception with a Logical Drive on 2 different PERC/storelib
disk ctlrs
Change : 22554
System : Any (HORIZON_XD)
Impact : Customer, Factory
Module : disk
Authors : marky
Test #1 : disk -f:2
Expect : Verify test passes, no exception occurs when logical drives exist on 2
PERC controllers
Expect : Verify "Does not support Defect Data List" is not printed for drives that
do not support it, with -ficore switch
Expect : Verify parameter switches work properly

Issue : FE033093 Changes to replace nth BP 0,1,2 backplane # with the Stomp
Chassis Sled# of the STASH storage sled=[FD33x+BP+HDD's]
Change : 22548
System : Odyssey in STOMP chassis with new STASH sleds containing "Dell FD33xS
HBA" and/or "Dell FD33xD HBA"
Impact : Factory only
Module : disk
Authors : marky
Test #1 : conf disk
Expect : Verify the Bay (middle number) of DriveChannelID C:B:S is the SLED number

Issue : Add support for STARK to assign Commodity (nvme_m2) to M.2 drives and
"WIDTH=??" M.2 or 2500
Change : 22520
System : STARK (rickon, sansa, arya)
Impact : Factory only
Module : disk
Authors : marky
Test #1 : conf disk
Expect : Verify (on STARK that) M.2 P/N 2M610 reports "WIDTH = M.2" and Commodity
= hard_drive(nvme_m2)

Issue : Remove front USB cable from Spitzer design.

Change : 22508
System : Spitzer
Impact : Customer, Factory
Module : cables
Authors : rods
Test #1 : cables -conf
Expect : Verify the list does not have FrontPanelUSBCable listed.

Issue : Add new batches for HDD buildVerify and looping and more features for
diskv.bat
Change : 22474,22497,22499
System : All
Impact : Factory only
Module : dowin/Dellmech
Authors : marky
Test #1 : Run hddbv.bat in factory (not lab network) to access mdiag HDD
buildVerify scripts in W: network drive
Expect : Verify it can be successfully run by developer(s)
Test #2 : Use factory or lab network and map developers s: drive then run below
from x:\wbt\RAMLibrary\Dellmech
 : or x:\tools\diags as is appropriate
: loop 100 s:diskv2.txt call diskv.bat test.txt . 1 percLog
Expect : Verify batches can be successfully run by developer(s), will stop on any
error (occurs for FE032708)
: and developer can monitor progress remotely by getting diskv2.txt from s:
drive. Verify for PERC
: that storelibdebug*.* text files are generated. Verify both loop.bat and
diskv.bat will start notepad
: on diskv3.txt and/or test.txt respectively, if called without .bat
extension and will not start
: notepad if .bat extension is used. In this example diskv.bat 3rd arg "1"
runs disk -v -trace -conf only
: The "." arg should be used as previous diskv.bat did not support it
correctly. RR5 lab network needs this.
Test #3 : loop 100 s:diskv2.txt call diskv.bat test.txt s:2 9 percLog
Expect : Verify above runs all diskv.bay tests (conf, ficore, & conf debug) and
uses disk2.exe from S: drive
: instead of the disk.exe. Previous diskv.bat had no support for 9 and
could only do 0 or 1 with the perLog arg
Test #4 : diskv.bat test.txt . 2
Expect : Verify above runs 2=confOnly
Test #5 : diskv.bat test.txt . 3
Expect : Verify above runs 3=ficoreOnly
Test #6 : diskv.bat test.txt . 4
Expect : Verify above runs 4=ficoreDebugOnly

Issue : JIT-108309 14G Spitzer 740XD2 Fan Sensors - DD 6104.3. Update Spitzer Fan
Type sensor numbers.
Change : 22486
System : Spitzer
Impact : Customer, Factory
Module : cables
Authors : rods
Test #1 : cables -conf
Expect : Verify the list contains a Fan Type line for each installed fan.

6104.4
-----------------------------------------------------------------------------------
----------------------------------
Issue : FE033078 Rolling back Darwin (Adaptec/PMC) updates due to HDD SMART
failures with latest *.dll and *.lib.
Change : 22465
System : All Adaptec/PMC HBAs
Impact : Customer, Factory
Module : disk
Authors : ymb
Test #1 : disk -f:7 or disk -f:23
Expect : Verify DST Short/Long or DEFT runs correctly and does not fail the SMART
dst ABORT command

Issue : WIDTH = 1500, HEIGHT = 2500 in -conf are backwards for SAS HDD's that
support Dell Unique modepage 0xDC
Change : 22438 (another fix like 22381)
System : All
Impact : Customer, Factory
Module : disk
Authors : marky
Test #1 : disk -conf
Expect : Verify WIDTH = 2500, HEIGHT = 1500 for SAS HDD's that support Dell Unique
modepage 0xDC
: with Dell FD33xD HBA

Issue : Added camera VID_0BDA PID_5520 to the INF files and signed the CAT files.
This is for Pinehills
Change : 22403
System : Pinehills
Impact : Factory
Module : USB Driver, DDUSBDiag
Authors : carl
Test #1 : ddusbdiag.exe
Expect : To find and test the camera 0BDA:5520 and not show driver not loaded
error message

6104.3
-----------------------------------------------------------------------------------
----------------------------------I
Issue : Remove Front VGA cable from design
Change : 22389
System : Spitzer
Impact : Customer, Factory
Module : Cables
Authors : rods
Test #1 : cables -conf
Expect : Verify Front VGA cable does not appear

Issue : FE033029 6104.2 is failing DEFT (from Disk rewrite for 22122, 22129,
22136, 22137, 22138, 22140)
Change : 22387
System : All
Impact : Customer, Factory
Module : disk
Authors : marky
Test #1 : disk -conf
Expect : Verify DEFT -f:23 works fine on systems with PERC's

Issue : 1 Disk.exe -flushcache -stbi fails on systems with Glist errors with !!!
USER ABORT CTRL-BREAK!!!
Issue : 2 FixInt - Identify S140 correctly for do/dowin/ePSA in Minotaur(Wind,
Soho, Stardust, Giotto)
Issue : 3 Debug memory dumps during disk testing are scrambled due to threads
Issue : 4 WIDTH = 1500, HEIGHT = 2500 in -conf are backwards for SAS HDD's that
support Dell Unique modepage 0xDC
Change : 22381
System : All
Impact : Customer, Factory
Module : disk
Authors : marky
Test #1 : disk -conf
Expect : 1 Verify glist errors do not hang/abort disk cmd lines besides -conf and
-ficore like -flushcache -stbi
: and P/N CN3JH, which does not support Glist, prints a GlistCount = 0
line in disk -conf
Expect : 2 Verify S140 is identified correctly for dowin on Minotaur systems
Expect : 3 Verify memory dumps are coherent and not mixed up during -f:{N} -v -
trace disk test output
Expect : 4 Verify WIDTH = 2500, HEIGHT = 1500 for SAS HDD's that support Dell
Unique modepage 0xDC
 : with Dell HBA330 MMZ

Issue : JIT-100237 and tons of email: Map PCI Slot 1 M.2 devices to storage Slot
8 & 9
Change : 22370 (disk.exe only)
System : Stark(Arya, Sansa, Rickon)
Impact : Customer, Factory
Module : disk
Authors : marky
Test #1 : disk -conf
Expect : Verify M.2 Slot is 4 for left side, 5 for right side of Riser in slot 5,
and
: Verify M.2 Slot is 8 for bottom Mezz and 9 for top Mezz in PCI Slot 1
: Verify PCI Bridge and the NVMe under it are NOT HHHL

Issue : FixExt Adding correct Adaptec libraries to support Darwin in 32 bit.

Issue found By FICORE.
Change : 22376
System : 32bit Adaptec
Impact : Customer, Factory
Module : disk
Authors : ymb
Test #1 : disk -conf
Expect : verify command completes successfully (ie, no exceptions).

Issue : New : Minotaur Updated S140 dll support to fix a drive slot numbering
issue.
Change : 22367
System : All S140 RAID
Impact : Customer, Factory
Module : disk
Authors : ymb
Test #1 : disk -conf
Expect : Drive slot number is correct and starts at 0.

Issue : Rewrite - ciaStor. Simplified the constructors/destructors. Removed "#if

FACTORY_ONLY".
Change : 22361
System : All
Impact : Customer, Factory
Module : disk
Authors : shuangw, marky
Test #1 : N/A (It's better tested on a system with two different iaStor)

Issue : Add support to diskv.bat to enablePERCLogging if desired, and to make

diskv.bat suitable to loop
Change : 22337
System : All
Impact : Factory only
Module : disk
Authors : marky
Test #1 : s:loop
Expect : Verify usage: 1.7 outputFile{.txt} [copyDrive:] [0=confandFicoreOnly
1=debugConfOnly] [enablePERClogging]
Test #2 : s:loop 50 diskv.txt call diskv.bat s2e.txt s:2 0 percLog
Expect : Verify diskv.txt stops if any disk cmd fails in diskv (-conf, -ficore, or
debug -conf)
: and verify for PERC's that storelibdebug*.txt files are generated
Issue : REWRITE fGListTest changes in 22304, Add fSenseStr decodes, fCmdNameScsi,
and defines for hard-coded values
Change : 22311
System : All
Impact : Customer, Factory
Module : disk
Authors : marky
Test #1 : diskv name.txt s:
Expect : Verify same output (except debug), and don't allow user to abort if not
in a test (cDriveCommands.cpp.10617)

6104.2
-----------------------------------------------------------------------------------
----------------------------------
Issue : HGST SAS SED drives cause -conf to abort testing (Kerry Aleman)
Change : 22304
System : Any with SAS SED drives (5JF6T, JFCC7, PH7M2)
Impact : Customer, Factory
Module : disk
Authors : marky
Test #1 : disk -conf
Expect : Verify test does not fail and does not appear aborted by the user
Expect : Verify GlistCount = 0 entries are list in the -conf output
Test #2 : disk -f:10
Expect : Verify Glist test does not fail

Issue : Breckenridge_P fails -f4 NVMe read sense 5-2400 INVALID_FIELD_IN_CDB

Change : 22286
System : All (Breckenridge_P)
Impact : Customer, Factory
Module : disk
Authors : marky
Test #1 : disk -f4
Expect : Verify test passes on NVMe using iaStorAC 16.0.2.1086 code line:
fNvmeRead(pDrvInfo, lba, numlbas)

Issue : FE032708 Exception on Sojourner NGM system with 91 HDD's

Change : 22278
System : 14G (Sojourner)
Impact : Customer, Factory
Module : disk
Authors : marky
Test #1 : disk -conf -xml -HHHLDir:X:\wbt\wbt_d\19\0 -o:x.xml
Test #2 : disk -ficore -HHHLDir:X:\wbt\wbt_d\19\0 -o:x.txt
Expect : Verify no exception occurs in cmdlines above

Issue : Fix disk -HDDFlash for BOSS drives when no DELLBOSS logical volume is
created
Change : 22273
System : 14G (Horizon)
Impact : Customer, Factory
Module : disk
Authors : marky,toddb
Test #1 : s:flash Micron_5100_D0DE005.fwh -d:hdd:1 -forceflash
Expect : Verify HDD firmware flashes and test passes with P/N GPGC0 as HDD:1 in
BOSS card

Issue : FixExt : If downstream ports have weird PCI slots values, use normal PCI
slot instead (DSS request)
Change : 22209
System : Pioneer (Pearl)
Impact : Customer, Factory
Module : SystemConfig.exe, pcie.exe, epsa
Authors : marky,ymb
Test #1 : Run systemconfig.exe -conf -noexe on Pioneer with TXWX2 HHHL installed.
Expect : Verify all 5 entries for each slot are consistent (probably 2 or 3) and
slots are not greater than 15.

Issue : (WSMT) BITS357547 [Cassini MLK] CHANGE REQUEST:ePSA sends SMI data to
BIOS, there will be CPU exception issue.
Change : 22203
System : All
Impact : Customer, Factory
Module : N/A
Authors : rods
Test #1 : This is primarily a PSA change, but due to shared source it could affect
WBDD. The low-level SMI issue
: is the concern.
Expect : No change in operation.

6104.1
-----------------------------------------------------------------------------------
----------------------------------
Issue : New : Initial Darwin support (new Adaptec/PMC/Microsemi controller).
Includes updated headers and drivers.
Change : 22177, 22182, 22189
System : DSS Servers
Impact : Factory & Customer
Module : disk.exe
Authors : ymb
Test #1 : disk -conf
Expect : Verify drives information is complete and correct, especially slot
numbers. No fatal exceptions from NULL string values.

Issue : Back out 22109 change

Change : 22174
System : Stark
Impact : Factory & Customer
Module : disk.exe
Authors : marky

Issue : Add support for "hard_drive(nvme_m2_consumer)" for Intel Neptune Harbor

(QLC) SSD targeting Nov Block FY19
Change : 22168
System : All
Impact : Factory & Customer
Module : disk.exe
Authors : marky
Test #1 : disk -conf
Expect : Verify hard_drive(nvme_m2_consumer) is Commodity type reported for
Neptune Harbor (nothing available yet)
Test #2 : systemConfig -sil
Expect : Verify hard_drive(nvme_m2_consumer) are logged using gHDDCommodityList[]

Issue : REWRITE fix 22162 for Kepler ATA drive to NOT run SAS/SCSI Read Buffer
Test in lab
Change : 22122, 22129, 22136, 22137, 22138, 22140, 22152, 22162
System : All
Impact : Factory & Customer
Module : disk.exe
Authors : marky
Test #1 : s:fx keplerATAHDD0.txt s: -f:1 -d:hdd:0
Expect : Verify Read Buffer Test does not run and rest of tests pass

Issue : REWRITE fix 22152 for fGetSASDefectListData to NOT call fDiskError if

just getting glist cnt (-ficore or -conf)
Change : 22122, 22129, 22136, 22137, 22138, 22140, 22152
System : All
Impact : Factory & Customer
Module : disk.exe
Authors : marky, ymb
Test #1 : Run -conf and/or -ficore on known bad drive.
Expect : Verify disk error does not occur

Issue : Add WBDD version to "dowin sysid f" so what.bat will show factory version
in diskv/cdump.bat
Change : 22149
System : All
Impact : Factory only
Module : dowin.exe
Authors : marky
Test #1 : Run what.bat and expect something like below in next release (or
610X.TIPS in unreleased dowin)
Expect : 6104.2 HRZNST5, PowerEdge R740xd, SYSID 0737, BIOS 1.2.11, CPLD 1.0.1,
IDRAC 3.00.00.00 (Build 69)

Issue : Disk rewrite. Lots of changes to simplfy code, use functions instead of
inline code, etc
Issue : BITS372366 Change Request [WBDD] force DEFT to stop running at the point
a HDD failure is detected
Change : 22122, 22129, 22136, 22137, 22138, 22140
System : All
Impact : Factory & Customer
Module : disk.exe
Authors : marky
Test #1 : Run all disk tests and -conf, -ficore, etc
Expect : Verify same as before
Test #2 : Run disk tests on known bad drive.
Expect : For any disk tests, if an error occurs, verify testing other devices in
other threads stop to save time.

Issue : Remove $PIR support. Now always use SMBIOS type 9 records instead for PCI
Slot #
Change : 22122
System : Client
Impact : Factory & Customer
Module : SystemConfig.exe
Authors : marky
Test #1 : SystemConfig -conf -noexe
Expect : Verify PCI build verify still works, and if it does not assign defects to
that platform BIOS if SMBIOS is not correct

Issue : JIT-100237 Map PCI Slot 1 slots 0..1 to 8..9 for build verify on Stark
(part 2, supplement 20311 change)
Change : 22109
System : Stark
Impact : Factory & Customer
Module : disk.exe
Authors : marky
Test #1 : Run "disk -conf"
Expect : Verify dual M.2 NVMe devices in Mezz card in PCI Slot 1, report Slots 8
and 9

Issue : FE032580 has 7 4x NIC PCIe cards and that causes systemconfig -sil to
fail
Change : 22094
System : All
Impact : Factory
Modules : systemconfig.exe
Authors : bbw
Test #1 : systemconfig.exe -sil -gcf:your_gcf_file_here
Expect : No error exit

Issue : FE032591 Matira throwing an exception on specific -FICORE debug message

Change : 22077
System : Matira
Impact : Factory, Customer
Modules : disk.exe
Authors : ymb
Test #1 : disk -ficore
Expect : All Physical Drives are reported in output
Expect : disk.exe completes and gracefully exits

Issue : FE032548 make Surveyor Universal Backplane bay0 and PCI bay1 in 0..24
workaround on C7 and C30.
Change : 22052
System : Surveyor
Impact : Factory, Customer
Modules : disk.exe
Authors : ymb
Test #1 : disk -conf
Expect : C7 Verify drives in bay1 are reporting slots 11..23 and drives in bay0
are reporting slots 0..11
Expect : C7 Verify bay1 is PCIE and bay0 is Universal

Issue : Change Request for Liqid Slot DSS FE032167 P/N TXWX2
Change : 22005, 22020
System : Pioneer
Impact : Factory, Customer
Modules : disk.exe
Authors : marky, ymb
Test #1 : disk -conf
Expect : Verify Liqid can be placed in slots 1 and / or 3 and still report HHHL

Issue : P/N V9N7N reports wrong subSystemID's and extra device

Issue : P/N V9N7N causes SystemConfg=B2? because the GPU's are realy VGA class
codes
Change : 21972, 22008
System : Surveyor, Trailbreaker2
Impact : Factory, Customer
Modules : systemconfig.exe, cables.exe
Authors : marky
Test #1 : systemconfig -conf -noexe
Expect : Verify ID's of V9N7N are correct, expecially 1022.1470.0000.0000
Test #2 : cables -conf
Expect : Verify (4) V9N7N's are reported as SystemConfg=B2 not B2?
Test #3 : psa -conf
Expect : Verify (4) V9N7N's are reported as SystemConfg=B2 not B2?

Issue : Support new Surveyor configs C7 and C30 FE032375

Change : 21943
System : Surveyor
Impact : Factory, Customer
Modules : disk.exe
Authors : ymb
Test #1 : disk.exe -conf
Expect : Verify slots 12..23 report correctly.

Issue : Speedup and simplify diskv.bat and cdump.bat

Change : 21930,21942,21970
System : All
Impact : Factory
Modules : dowin.exe,diskv.bat,cdump.bat
Authors : marky
Test #1 : diskv.bat diskv.txt
Expect : Verify dowin prints servicetag, model, BIOS, (and CPLD and iDrac fw for
servers)
: and systemConfig output is removed. Examples:
: 1FX4HM2, Latitude 7390 2-in-1, SYSID 0823, BIOS 1.1.4
: HRZNST5, PowerEdge R740xd, SYSID 0737, BIOS 1.2.11, CPLD 1.0.1, IDRAC
3.00.00.00 (Build 69)
Test #2 : cdump.bat cdump.txt
Expect : Verify cdump does the same thing, removes systemConfig and new dowin
support prints servicetag and model

Issue : FIWIOT-367 : Wyse systems not working correctly with -ficore switch.
Change : 21924
System : Wyse (San Bernardino)
Impact : Factory, Customer
Modules : disk.exe
Authors : ymb
Test #1 : Run disk -ficore multiple times
Expect : Output is correct and consistent for each run.
Expect : Run "diskpart" and verify command completes in a reasonable amount of
time (a few seconds)

Issue : Initial Cables support for Spitzer.

Change : 21908
System : Spitzer
Impact : Factory, Customer
Modules : cables.exe
Authors : rods
Test #1 : Run cables -conf
Expect : Cables connections as expected.

Issue : Initial Cables support for Minotaur systems. Add Cannon Lake PCH GPIO
access class.
Change : 21900
System : Giotto, Stardust, Soho, Wind
Impact : Factory, Customer
Modules : cables.exe
Authors : shuangw, rods
Test #1 : Run cables -conf
Expect : Cables connections as expected.
Issue : FE032234, FE032237, FE032179, FE031701, FE032014 Remove Buffer
manipulation for Marvel Read Sector No Data
Issue : Enable Marvel on SeqSeek Test
Change : 21887
System : Any system with BOSS/Marvel
Impact : Factory, Customer
Modules : disk.exe
Authors : ymb, marky, toddb
Test #1 : Run disk.exe -f:3
Expect : Verify Random Seek Test completes
Expect : Verify Marvel drives runs SeqSeek test for 30 minutes

Issue : FE032119, FE032127, BITS368110 Workaround Toshiba issue when it is 70% of

client supply and getting 5% failures.
Change : 21870
System : Client with Toshiba NVME
Impact : Factory
Modules : disk.exe
Authors : marky
Test #1 : Run disk.exe -f:7 two times
Expect : No prior DST failures for controller reset

Issue : Re-visit JIT-65179 and update Inlet temp sensor to only ignore UPPER
level threshold (14G only). Add
: decode of iDrac record used to indicate a sensor hardware failure (14G
only). Add better decode of
: threshold violations to show text of threshold. Move previous workaround
in eventlog library to ipmi
: library so the text in the message has the severity that matches how it
is treated.
Change : 21823
System : 14G Servers
Impact : Factory
Modules : Ipmi library, Eventlog library
Authors : rods
Test #1 : Run "servermgmt"
Expect : Should not fail due to Inlet sensor or SEL entry for Inlet UPPER
threshold violation.
Test #2 : Run "eventlog"
Expect : Should not fail due to SEL entry for Inlet sensor UPPER threshold
violation.

Issue : Fix HBA330 MX code to force bay 0 in DriveChannelID C:B:S, not use 1
found in MR_ENCL_INFO/MR_ENCL_INFO_EXT
Change : 21817
System : Skylynx
Impact : Factory,Customer
Modules : Disk
Authors : marky
Test #1 : disk.exe -conf
Expect : Verify DriveChannelID of HDD's in local 6-slot bay of HBA330 MX are 0 not
1

Issue : BITS371363 Correct Bison ODD detected at id 2

Change : 21809
System : All
Impact : Factory,Customer
Modules : Disk
Authors : marky
Test #1 : disk.exe -conf
Expect : Verify ODD DriveChannelID

Issue : FE032167 Add support for TXWX2: new DSS LIQID Element HHHL, to report
HHHL (#3 of 3)
Change : 21710,21761,21810
System : Server
Impact : Factory
Modules : disk
Authors : marky
Test #1 : disk -conf
Expect : Verify TXWX2 reports as HHHL in PCI Slots 2 and 3 (was Slot 1 & 3 in
change 21710)

Issue : FixInt Display WriteCache in xml conf output

Change : 21805
System : All
Impact : Factory,Customer
Modules : Disk
Authors : marky, toddb
Test #1 : disk.exe -conf -xml
Expect : Verify WriteCache is displayed in output

Issue : FE032157 Run SCSI PT for SAS9311-8i instead of using storlibir3

Change : 21801
System : All
Impact : Factory,Customer
Modules : Disk
Authors : toddb, ymb
Test #1 : disk.exe -f:2 -mon -xml
Expect : Verify all tests run to completion successfully

Issue : BITS370890/FE032145 P/N KV46M/5WDTX report AddInDevice NO, which is

wrong
Change : 21765,21767
System : Server
Impact : Factory
Modules : systemConfig
Authors : marky
Test #1 : systemConfig -conf -noexe
Expect : Verify P/N KV46M/5WDTX SerialI/OCard reports
<AddInDevice>YES</AddInDevice>

Issue : FixExt : FE030661 and FE031950 variable used to run SPT needs to be reset
between devices.
Change : 21763
System : Server
Impact : Factory
Modules : disk
Authors : marky, ymb
Test #1 : disk -f:7
Expect : Verify DST runs correctly using LCP scsi commands instead of SPT commands
(-v needed)

Issue : FE032167 Add support for TXWX2: new DSS LIQID Element HHHL, to report
HHHL (#2 of 3)
Issue : FE032172 KEPLER dual-BP does NOT report slots 0..23 when PERC is NOT
attached
Change : 21710,21761
System : Server
Impact : Factory
Modules : disk
Authors : marky
Test #1 : disk -conf
Expect : Verify dual-BP X24 backplane on KEPLER reports HDD's in slots 0..23, not
0..11,0..11

Issue : FE032107 Handle rare case of Insight HDD's reported before local BP
HDD's. Fix DriveChannelID/slot/bay numbers
Change : 21756,21757
System : Server (NGM systems, especially H745P MX servicetag PT56745)
Impact : Factory
Modules : disk
Authors : marky
Test #1 : disk -conf
Expect : Verify HDD's in local backplane and Insight sleds report the correct bay
and slot information

Issue : FixInt: BITS365844 [Punisher 22 & 24] WBDD 6101.3 Pic cannot be showed
correctly during "video.exe -pattern" test
Details : The video "pattern" test does not fit the screen size. If the 1024 x 768
mode is not supported in the WinPE image and hardware, fail the test.
: That size is required for the pattern to display properly. Added more
tracking debug statements for the -pattern test option.
Change : 21754
System : any
Impact : Factory, System Development testing
Modules : Video.exe
Authors : carl
Test #1 : video.exe -pattern
Test #2 : video.exe -pattern -v
Expect : Test to display the screen properly if 1024x768 is a valid screen mode
for the WinPE driver being used.
Expect : Error exit and message that screen size of 1024x768 is not supported if
that mode is not present.

Issue : FE032037 - Fan test showing -1 for the RPM.

Details : Corner case - if the fan speed request SMI is called (0x02 0xA3) and the
fan speed is 675, which is also 0x02A3, then
: return the fan speed back as 675. Otherwise BIOS needs to add 1 to the
fan speed so the registers changed.
Change : 21741, 21745, 21779
System : Matera 3/5/7/3X
Impact : Factory
Modules : fan
Authors : carl
Test #1 : fan.exe
Expect : Fan test to pass if fan RPM is exactly 675 and not show a value of -1 for
the fan speed.

6103.4
-----------------------------------------------------------------------------------
----------------------------------

Issue : FE032081 Fix for SN200 P/N MF3FM to A) Not create duplicate PCIe
bridges/drives and B) Make it report 2.5" not HHHL
Change : 21733
System : Server
Impact : Factory
Modules : disk
Authors : marky
Test #1 : disk -conf
Expect : Verify statements in Issue: line above
Expect : Verify P/N MFM3FM reports "Vendor = HGST"

Issue : Trailbreaker2 replaces config "L2" with "M2".

Change : 21724
System : Trailbreaker2
Impact : Factory, Customer
Modules : Cables
Authors : shuangw
Test #1 : run "cables.exe -conf" on Trailbreaker2 config M2
Expect : Verify it's config M2

6103.3
-----------------------------------------------------------------------------------
----------------------------------

Issue : FE032047 disk -ficore gets exception on HorizonXD with RAID 6 over 12
HDD's
Change : 21710,21712,21718
System : Server
Impact : Factory
Modules : disk
Authors : marky, ymb
Test #1 : disk -ficore
Expect : Verify no exception occurs
Expect : #PhysicalDrive -ficore header is printed even if no PhysicalDrives are
present

Issue : Add support for TXWX2: new DSS LIQID Element HHHL, to report HHHL (#1 of
2)
Change : 21710
System : Server
Impact : Factory
Modules : disk
Authors : marky
Test #1 : disk -conf
Expect : Verify TXWX2 reports as HHHL

6103.2
-----------------------------------------------------------------------------------
----------------------------------

Issue : FE032009 Fix cBpInfo rewrite to ignore errors for Joint Mode else rear BP
does not get added
Change : 21683
System : Any with backplanes
Impact : Factory
Modules : disk
Authors : marky, ymb
Test #1 : disk -conf
Expect : Verify all backplanes are added, especially secondary ones

Issue : Workaround FE031759 when WMIC reports a HDD in an Insight sled *twice*
due to Multipath I/O (MMIO) enabled
Change : 21671
System : Any with HBA330 MMZ with MMIO enabled producing duplicate S/N's for "WMIC
path Win32_DiskDrive get PNPDeviceID SerialNumber"
Impact : Factory
Modules : disk
Authors : marky
Test #1 : disk -ficore
Expect : Verify :3HDDTyp: field reports :INSIGHT: for HDD's in an Insight storage
sled seen by HBA330 MMZ

Issue : FE031125 Capture and report NVMEs inside of Intel RAID configs,
corrections for Intel legacy boot mode
Change : 21633, 21668
System : ZumaP Intel Ronin
Impact : Factory,Customer
Modules : disk
Authors : ymb, marky
Test #1 : Run "disk -conf"
Expect : Verify correct hdd build configuration
Test #1 : Run "disk -ficore"
Expect : Verify correct ficore output, specifically PhysicalDrive# enumeration

Issue : JIT-88480 Shoemaker GPU Temp sensor not displaying correctly

Change : 21605
System : Shoemaker
Impact : Factory,Customer
Modules : Cables
Authors : toddb
Test #1 : Run "cables -conf"
Expect : Verify configuration output shows correct GPU Temp sensors based on slot

Issue : JIT-97911 Shoemaker Risers not see with NVMe, New riser types 1E/1F,
2E/2F added.
Change : 21600
System : Shoemaker
Impact : Factory,Customer
Modules : Cables
Authors : toddb
Test #1 : Run "cables -conf"
Expect : Verify configuration output shows correct Riser type

Issue : Physical Slots is sometimes wrong

Change : 21598
System : Servers
Impact : Customer, Factory
Module : PCIe
Authors : marky
Test #1 : run ePSA or PCIe.exe -conf
Expect : Verify PCIe.exe PCIePhysicalSlots or ePSA "Physical Slots" count in
[ PCIe ] section of Configuration tab
: is correct, especially for NVMe backplanes

Issue : FE031833 If IPMI fails on Mercury and passes the 14G Get Host Backplane
Topology Command
: FE031610 For Shoemaker and Kepler, create an extendedBp with a single
PCIe Internal Bridge and adjust the slot #'s to 0..23
Change : 21554
System : Servers(Shoemaker 2U, Kepler, Mercury)
Impact : Factory
Modules : Disk
Authors : marky
Test #1 : Disk -conf
Expect : Verify Kepler and Shoemaker with 12 x 2.5" SAS/PCIe plus 12 x 2.5" PCIe
show all NVMe drives under
: a single Internal PCIe Bridge. Verify PortCount is 24
: Verify HorizonN does not change, each External PCIe Bridge has 1 of the 2
12 x 2.5" PCIe BP's and Slot numbers are 0..11
: Verify PortCount is 12 for each PCIe Bridge conencted to front 24 slot
backplane
: Verify Mercury, if Topology command returns no backplanes, that the Bay
and Slot numbers for NVMe will still be correct

Issue : BITS365018 Add support for hard_drive(nvme_u2_upr) P/N 0FKXJ, Remove

COMMODITY2 support, change (client only)
: hard_drive(sataexp_nvme) to hard_drive(nvme_u2) and change
hard_drive(sataexp_nvme_sed) to hard_drive(nvme_u2_sed)
Change : 21504
System : Matira3/5/7
Impact : Factory
Modules : Disk
Authors : marky
Test #1 : Install 2.5" NVMe P/N 0FKXJ
Expect : Verify Commodity is hard_drive(nvme_u2_upr)

Issue : FixExt: When driver is not stornvme, disk could not detect SED devices in
fCheckSecurityProtocols
Change : 21481,21495,21496
System : Client
Impact : Customer, Factory
Modules : Disk
Authors : marky
Test #1 : Install SED drive P/N V9D2K and U2 NVMe P/N 0FKXJ
Expect : Verify SED device can be detected as SED hard_drive(sataexp_nvme_sed) for
m_iaRmvd, and
: Verify both the SED and U2 drive shows "Discovery Dump:" for -v

6103.1
-----------------------------------------------------------------------------------
----------------------------------

Issue : FixInt: changed ciaStor constructors to properly add all scsi devices and
not just the first one found. Needed for Intel controllers in Ronin mode.
Change : 21415
System : Client Intel
Impact : Customer, Factory
Modules : disk
Authors : ymb
Test #1 : run disk -conf
Expect : All controllers and devices correctly display all information

Issue : JIT-94711 FE031461 Sojourner PCIe generic test not clear

Change : 21410,21413
System : Servers
Impact : Customer
Modules : PCIe
Authors : marky
Test #1 : ePSA: Examine [ PCIe ] Configuration tab section and Run PCIe device test
Test #2 : WBDD: pcie -conf, and pcie -util:1
Expect : Verify PCI "Slot" numbers are now reported as "PCIe Slot {X}" for true
PCI slots and
: Verify NVMe drives in backplanes are reported as "Bay{N} Slot {XX}"
instead of PCI Slot 169, etc
Test #3 : Verify "pcie" no args defaults to -util:1 test all devices
(Client&Server) to align with ePSA

Issue : FixInt: Correct exception when printing raidset number when there is no
raid
Change : 21408
System : Intel non-RAID
Impact : Customer, Factory
Modules : disk
Authors : ymb, marky
Test #1 : run disk -conf with legacy Intel chipset and no VMD
Expect : no exceptions

Issue : Fix spelling of "detected" in a Warning message for the Charger

Change : 21384
System : all notebooks
Impact : Customer
Modules : Battery, Charger
Authors : MikeL, Carl
Test #1 : run battery.exe and verify if a charger error occurs that the word is
"detected" in the message.
Expect : Correct spelling of the word "detected" in the message.

Issue : FIXEXT: FE031531 Fixed Fatal Exception with two storlib type controllers;
device variable dl gets re-used multiple times incorrectly
Issue : FIXEXT: FE031545/JIT-95440 ngmBP move and use instead of dl->m_bpBay to
detect unassigned Insights
Issue : FIXINT: Ensure GList/get defects are included for storlib type devices
Change : 21374
System : Arya, NGM
Impact : Factory, Customer
Modules : disk
Authors : ymb, marky
Test #1 : run disk -conf with 2 different PERC or SAS controllers
Expect : No fatal exceptions, glist entries are included
Test #2 : run disk �conf on an H745P that is returning all zeros for 2nd
MRC_ENCL_INFO for unassigned Insight
Expect : Verify unassigned Insight BP1 is not even displayed (was reporting 0 x
2.5� backplane)

Issue : Add support for Matira 3X that uses the Skylake-X/Kaby Lake CPU
Change : 21366
System : Matira 3X
Impact : Customer
Modules : SAL, UI
Authors : carl
Test #1 : run EPSA
Expect : Expect disk tests to operate properly.

Issue : FixExt - JIT-94145 Additional check for NGM

Change : 21332
System : Pathfinder/Sojourner
Modules : disk
Authors : marky,toddb
Test #1 : disk -conf
Expect : Verify exception does not occur in MR_ENCL_INFO_EXT code
Issue : Add ability for mdiags to script diskv.bat for mdiag failures, without
starting notepad, if run as "diskv.bat"
Change : 21320
System : All
Modules : dowin/disk
Authors : marky
Test #1 : Verify "diskv file.txt" will run disk and start notepad on the the output
file
Test #2 : Verify "diskv.bat file.txt" will run disk (does not start notepad so it
can be scripted)

Issue : Add Copyrights to Disk files

Change : 21315
System : All
Modules : disk
Authors : shuangw
Test #1 : N/A

6102.2
-----------------------------------------------------------------------------------
----------------------------------
Issue : Fix to add tests to optical devices broken in change 21157
Change : 21299
System : All
Modules : disk
Authors : marky
Test #1 : disk -f:1 -d:cdrom -mon
Expect : Verify optical devices have tests installed and pass

Issue : FixExt - BITS363703 Latest Marvel dll did not work in WinRE due to side-
by-side error with libapr-1.dll.
: Received new mv_api.dll that does not require libapr-1.dll.
Change : 21296
System : Cassini/SOS
Modules : disk
Authors : ymb
Test #1 : disk -conf
Expect : Verify exception does not occur at exe launch

Issue : FixExt - JIT-94145 Add correct 15.02 storelibir-3.dll in release

Change : 21294
System : Pathfinder/Sojourner
Modules : disk
Authors : marky,ymb
Test #1 : disk -conf
Expect : Verify exception does not occur in MR_ENCL_INFO_EXT code

Issue : FixExt - BITS365445 BITS � Letter disappeared during RGB test on Punisher
22 & 24 KBL
Change : 21290
System : All
Impact : Factory
Modules : Video
Authors : srirami
Test #1 : Run the command "video.exe -rgb -colors:rgb -delay:1 -rk:no"
Expect : All characters should be displayed on the screen.

6102.1
-----------------------------------------------------------------------------------
----------------------------------
Issue : Changes to add missing fields to -conf for ARRAY and RAID(Not_Applicable)
devices, but mostly to make
: -ficore report RAIDSlots and PCIids for logical volumes so they can
determin where to install the OS
Change : 21273
System : Pearl/Matira RSTe, Intel iRST, VROC, S140, S130
Modules : disk.exe
Authors : marky, ymb
Test #1 : Run disk.exe -conf and verify all information is correct. May have new
SasId lines for ARRAY and various PD_* lines.
: Many hex values are now uppercased. Make VROC/VMD RAID ctlr Internal not
External. Fix VROC/VMD subid's swapped in 8086201D00008086
: Use PCI Tag 8D instead of 1105 for chipset disk ctlrs "ControllerId"
(just converted to hex so it is not so obscure)
: Don't print Width & Height in -conf if ""
Test #2 : Run disk.exe -ficore. Added new #PhysicalDrive header line to help
describe fields and extra SPACES so field withs are constant
: Verify RAIDSlots and similiar fields are correct for logical volumes, and
PCIID field 18VIDDIDSVIDSDID is correct

Issue : FixExt: FE030661 Transition LogSense to SPT as part of the drive testing
i/o move from ir3.
Change : 21268
System : 14G HBA330
Modules : disk.exe
Authors : ymb
Test #1 : Run disk.exe -f:23 and verify test completes (no "hangs").
Test #2 : Run disk.exe -f:3 and verify test completes (no "hangs").

Issue : New : Adding DST support to Intel iRST versions 15.9 and above. Includes
changes to support HDD f:13 and f:25 (DST delayed wait for complete).
Change : 21227, 21253
System : Matira RSTe, all Intel iRST
Modules : disk.exe
Authors : ymb
Test #1 : Run disk.exe -conf and verify all information is correct.
Test #2 : Run disk.exe -f:3, with nvme, SAS, SATA; verify tests runs successfully
if functions supported
Test #3 : Run disk.exe with each of the following: -f:7, -f:8, -f:12 with -f:13, -
f:23, -f:24 with -f:25 with nvme, SAS, SATA. and verify tests runs successfully if
functions supported. NVME with run Health Test only without DST support.

Issue : FixExt: BITS363703 updating marvel x64 drivers to support both Factory
and SOS WinRE processes.
Change : 21213
System : Client SOS WinRE
Modules : disk.exe
Authors : ymb
Test #1 : Successfully run disk -f:3 in SOS WinRE environment
Expect : Successfully run disk -f:3 in Factory Client / Server environment

Issue : [BITS345899] [EVT_B&BP CFL] Incorrect sounds output when run ePSA
Issue : Fix scan of D4 and DA tokens to look for Token = 0xFFFF instead of Value
= 0xFFFF when skipping tokens.
Reason : BIOS has a new required mode from Microsoft. In that mode Timer 2 is
disabled so no audio is possible
Change : 21208
System : Berlinetta CFL, Berlinetta P CFL
Modules : beep.exe
Authors : carl
Test #1 : n/a
Expect : n/a

Issue : Finish Line fan test, do not pass the low limit check if the fan is
unplugged (0 RPM).
Change : 21198
System : All
Impact : Customer, Factory
Modules : fan
Authors : carl
Test #1 : fan.exe
Expect : Pass normally. Fails the low speed test if the fan is unplugged and
showing 0 RPM.

Issue : New support to report error if no HDD's are found

Change : 21107
System : All
Impact : Customer Only
Modules : disk
Authors : marky
Test #1 : Run this on system with no HDD's: disk -f:3
Expect : Factory: Just pass, Customer: Report error 0x136, "No Hard Drives were
found"

6101.9
-----------------------------------------------------------------------------------
----------------------------------

Issue : FixExt: FE031014 Updated Kenworth to correctly report backplane

information by "forcing" LSI 9311 to support enclosure enumeration.
Change : 21220
System : Kenworth, all platforms supporting LSI 9311
Modules : disk.exe
Authors : ymb, marky
Test #1 : Run disk.exe -conf and verify backplane information is correct.
Test #2 : Run disk.exe -conf and verify DriveChannelID information is correct.

6101.8
-----------------------------------------------------------------------------------
----------------------------------
Issue : FixExt: BITS362669 memory time out during MarchLR test algorithm as the
data cache is disabled.
Change : 21126
System : All
Impact : Factory
Modules : memory
Authors : bbw
Test #1 : memory test with any options that include "MarchLR, Mats, PMOVI, or
ECCTestA"
Expect : Test should not timeout

Issue : Fix detection of M.2 P/N 26M10 to report M.2 not HHHL as code matched P/N
VTTNM Nytro 5910 HHHL
Change : 21106
System : Server DSS
Impact : Factory
Modules : disk
Authors : marky
Test #1 : disk -conf
Expect : Verify P/N 26M10 reported as M.2 and P/N VTTNM reported as HHHL

Issue : Fix detection of future OptaneMemory model strings

Change : 21105
System : Client (no impact until future Optane models become available)
Impact : None
Modules : disk
Authors : marky
Test #1 : disk -conf
Expect : Verify Optane Memory (future Gen 4) detected as M.2 devices

Issue : WinEPSA Build PostBuildEvent reports: The process cannot access the
file ...
Change : 21101
System : IT Notebooks
Impact : None
Modules : WinEPSA
Authors : marky
Test #1 : Build/Compile/Run WinEPSA in Debug/Release X64 (Run As Adminsitrator)
Expect : Verify no issues and no error like below in PostBuildEvent:
: The process cannot access the file because it is being used by another
process

6101.7
-----------------------------------------------------------------------------------
----------------------------------
Issue : Shoemaker Cables update for Riser / PCIE configuration
Change : 21062
System : Shoemaker
Impact : Factory,Customer
Modules : Cables
Authors : toddb
Test #1 : cables.exe -conf
Expect : Verify cables output has correct slots under Risers

Issue : Full support for SkyLynx H745p MX amd HBA330 MMZ

Change : 21060, 21067, 21069
System : Pathfinder/Sojourner
Modules : disk
Authors : marky,ymbf
Test #1 : disk -conf
Expect : Verify Insight backplanes are reported with the "bay" being the Sled #
: Verify unassigned Insights are not reported (backplanes without any
HDD's)
: Verify HDD's bay matches the Insight sled # they are in
: Verify Insight backplanes product: "BPNGM+EXP" are "type: 16 X 2.5" SAS"
: Verify BP's are correct when only 2 sleds are in the system

6101.6
-----------------------------------------------------------------------------------
----------------------------------
Issue : SkyLynx H745p MX remove unassigned BPNGM+EXP BP's
Change : 21024
System : Pathfinder/Sojourner
Modules : disk
Authors : marky
Test #1 : disk -conf
Expect : Verify unassigned BP's are not reported

Issue : FixExt: FE030661 Part 2 Adding SPT support for DEFT/DST on HBA330 (not
using storlib for drives we have access to)
Change : 21008
System : 14G with HBA330
Modules : disk
Authors : ymb
Test #1 : disk -f:23
Expect : DEFT/DST test runs to completion without a "hang"

Issue : SkyLynx H745P MX backplane reports 0 x Empty

Change : 21003
System : Pathfinder/Sojourner
Modules : disk
Authors : marky
Test #1 : disk -conf
Expect : Verify backplane reports 6 x 2.5" SAS/SATA

Issue : FE030663 Kenworth with 46 drives gets timer not started error when second
batch of drives start testing
Change : 20991
System : Kenworth (with more that 25 hard drives)
Modules : disk
Authors : toddb
Test #1 : disk -f:23 -t:6480 -mon
Expect : Test to pass with no timer not started errors when second batch of drives
start testing.

Issue : Merge do/dowin code and add shared new file pciVendStr.h
Change : 20984, 20996
System : All
Modules : do.efi and dowin.exe
Authors : marky
Test #1 : UEFI: cdump, WBDD: cdump.bat
Expect : Same PCI device strings are used, etc
Test #2 : UEFI: cdump, WBDD: cdump.bat
Expect : Verify "Other Periphera" devices are NOT show in cdump.bat/cdump.efi (but
are in do cdump and dowin cdump)

Issue : Video memory test fails at first address on NV-17 video controller.
(Cassini, Firelord KBL).
Issue : Error code is 0x0E0A (older versions of DellDiags) or 0x550A. The key is
0A instead of 04 (did not find controller)
Issue : BITS308333 CASSINI 17 Dell WinPE Diagnostics v6089 Video Failures
Issue : BITS303189 [FL_KBL_DVT2.0] Video device show the failure when run
delldiag under WinPE environment
Change : 20976
System : Systems using NV-17 video controller and Intel chipset video controller
Modules : video
Authors : carl
Test #1 : video.exe -f:1
Expect : Video test to run on the Intel chipset controller and skip the NV-17
since it is enabled, but memory not enabled
Expect : No failure read/write during video initialization scan test of the first
memory address.
Test #2 : video.exe -f:2
Expect : Extended video test to run on Intel chipset controller and skip the NV-17
controller.
Test #3 : video.exe -f:3
Expect : Extended video test to run on Intel chipset controller and skip the NV-17
controller.

Issue : Add modern processors to the fGetProcessorFamily() for the

ProcessorFamily token in SystemConfig.exe
Change : 20973, 20975
System : Intel CPU based systems
Modules : systemconfig
Authors : carl
Test #1 : systemconfig.exe
Expect : Processor Device information to show string for ProcessorFamily token
instead of Unknown

6101.5
-----------------------------------------------------------------------------------
----------------------------------

Issue : FixExt: FE030769 Updated Marvel APIs

Change : 20961
System : Horizon/Pioneer with BOSS firmware 1.1 (Portsmouth)
Modules : disk
Authors : ymb
Test #1 : disk -HDDFlash
Expect : Firmware updates without returning an error
Expect : drive does not go offline

Issue : FixExt: FE030661 Adding SPT support for DEFT/DST on HBA330 (not using
storlib for drives we have access to)
Change : 20958
System : 14G with HBA330
Modules : disk
Authors : ymb
Test #1 : disk -f:23
Expect : DEFT/DST test runs to completion without a "hang"

Issue : Add CPU Production detection for Gemini Lake CPU

Change : 20951
System : Gemini Lake (GLK) based systems
Modules : systemconfig
Authors : carl
Test #1 : systemconfig.exe
Expect : Production CPU to show it is a production level part instead of "UNKNOWN"

Issue : MORE Fixes for JIT-87161 SYS_SOJOURNER & SYS_PATHFINDER and storage sleds
in Insight
Change : 20946
System : Insight chassis with storage sleds and compute sleds
Impact : Factory
Modules : disk
Authors : marky
Test #1 : disk -conf
Expect : Verify build verify scripts work, especially for Sleds 1..8

Issue : (ID's changed since 19453) Request for DSS Transactional HHHL NVMe - add
PCI ID for Liqid MPN LQD-E1APN04M006T40
Change : 20917,20920
System : PIONEER
Impact : Factory,Customer
Modules : Disk
Authors : marky
Test #1 : disk.exe -conf -o:disk.txt
Expect : Device recognizes the Bridge and NVMe in this HHHL and HHHL on PIONEER
with 2 Liqid P/N 5DH84 in Slot 1 and 3.

Issue : FixInt: Stop Customer OS testing from using invalid data from the Windows
NUMA node information API (was given NUMA node memory size of 0).
Change : 20887
System : any
Impact : Factory, Customer
Modules : Memory
Authors : brad
Test #1 : memory.exe -f:1
Expect : No failure or halt at about 50% memory testing on system with NUMA node
with 0 memory associated with it.

6101.4
-----------------------------------------------------------------------------------
----------------------------------
Issue : JIT-87161 Insight234.txt fixes for SYS_SOJOURNER & SYS_PATHFINDER and
storage sleds in Insight
Change : 20896
System : Insight chassis with storage sleds and compute sleds
Impact : Factory
Modules : disk
Authors : marky
Test #1 : disk -conf
Expect : Verify build verify scripts work, Conf output should show BP's 0(IPMI BP
on compute sled), 2,3,4(storage sleds 2,3,4, sled 1 empty)
: and the DriveChannelId is correct for the Bay and slots, etc. ePSA (no
code change) match, BP Slots are 64,65,66,67 (0x40..43 in disk.exe)

Issue : FixExt: FE030521 for HBA330 if no PhysicalDrive available then revert to

using ir3 library
Change : 20891
System : All
Impact : Factory
Modules : disk
Authors : marky,ymb
Test #1 : disk -f:3
Expect : Verify test completes without error on HBA330 systems

6101.3
-----------------------------------------------------------------------------------
----------------------------------
Issue : Fix video -f:1 to actually run the test instead of failing on Pearl and
AvalonR
Change : 20869
System : All
Impact : Factory
Modules : video
Authors : marky,ymb,toddb
Test #1 : video -f:1
Expect : Verify test completes without error on Pearl and AvalonR
Expect : Verify aborting test does not print "Fatal: Device test result not
reported!" if testing is aborted
Expect : Verify Firestart_15_KBL does not report "Can't retrieve video
configuration, for example the video virtual address"
: although the one in the lab seriveTag 54RX262 has real video memory
failure

Issue : FixInt : BITS357452 Fix GPF when we examine WMI class element and the
WinPE image does not have WMI enabled.
Change : 20867
System : Firestar MLK, Firestar-B, Armani 15 MLK
Impact : Factory
Modules : disk
Authors : carl
Test #1 : disk -conf
Expect : No exception error 5. If WMI is not enabled then the drives not found
will not be
displayed in the configuration.

Issue : FE030568 Sata drives on PMC 8805 run DST instead of DEFT, even when DEFT
is supported by the HDD
Change : 20855
System : Any with PMC controller and SATA drives
Impact : Factory,Customer
Modules : disk
Authors : marky
Test #1 : Sys:deft.bat
Expect : Verify SATA HDD's on PMC 8805 run DEFT, if DEFT is supported, not DST

Issue : FE030286 Disk -f:23 has file lock on XML output file. Similiar to
FE029842 (Trailbreaker 2). Added fMsg.
Change : 20853
System : Mercury
Impact : Factory only
Modules : disk
Authors : toddb
Test #1 : disk -f:23 -mon -xml -o:disk.xml
Expect : Verify disk exits and can access disk.xml

Issue : FE030485 fail PCI build verify on HorizonN for "extra" PLX:9781 devices
in Slot 4
Change : 20849
System : Horizon_XD
Impact : Factory only
Modules : SystemConfig
Authors : marky,toddb
Test #1 : SystemConfig -noexe -o:sysCfg.txt
Expect : Verify PLX 9781 devices, 10B5 9781 1028 1FE8, report Slot 0 not Slot 4

6101.2
-----------------------------------------------------------------------------------
----------------------------------
Issue : New - Add support for iastorac.sys per email request from CDC Test
Strategy
Change : 20816
System : All (Client iRST driver version 16.0)
Impact : Factory,Customer
Modules : Disk
Authors : ymb,toddb
Test #1 : disk.exe -conf
Expect : Verify iRST version 16.0 systems report configuration correctly
Note : Support not yet available.
Issue : FE030472 ADC LAB-PS3 - 14G - KEPLER C30x24 -drive2ctlr\005\buildverify.py

Change : 20809
System : All(NewFrontier, Kona)
Impact : Factory,Customer
Modules : Disk
Authors : marky,toddb
Test #1 : disk.exe -conf
Expect : Verify Kepler/Helios/Surveyor PCIe Bridge cards report Internal and only
one added no matter how many NVMe attached
Expect : Verify similar thing for Kona
Expect : Verify Kepler/Helios/Surveyor AHCI controllers (and maybe other systems)
report Internal
Note : ePSA\Modules\Disk\cDisk.h changes should be also added/modified to ADDF\
Disk\ide.h and disks.hpp

Issue : FE030449 - Remove Pearl from 14G motherboard port remapping function
Change : 20804
System : Pearl
Impact : Factory,Customer
Modules : disk
Authors : ymb
Test #1 : Run disk - conf
Expect : Verify correct slot placement of drives

6101.1
-----------------------------------------------------------------------------------
----------------------------------
Issue : Add support for Mormont to Cables
Change : 20773
System : Mormont
Impact : Factory,Customer
Modules : cables
Authors : rods
Test #1 : Run "cables -conf"
Expect : Verify Cables information shows

6100.8
-----------------------------------------------------------------------------------
----------------------------------
Issue : BITS351605 Intel driver comparison corrected to >= 15.1 instead of (>14
and >0) which fails for new driver version 16.0
Change : 20759
System : Tunnels (iRST with driver version 16.0)
Impact : Factory,Customer
Modules : Disk
Authors : ymb, marky
Test #1 : disk.exe -conf
Expect : Verify slot numbering is correct in conf output

Issue : FE030216 CDROM Slot 7 conflicts with HDD in Slot when S140 mode only,
back out Slot 11 change, etc
Change : 20712, 20734, 20739, 20756
System : All(14G)
Impact : Factory,Customer
Modules : Disk
Authors : marky,toddb
Test #1 : disk.exe -conf
Expect : Verify any CDROM in 2nd S140 ctlr is Slot 7 and HDD's 2nd ctlr (actually
both) are Slots 0..3 (AHCI & S140)

Issue : Add support to decode SANDISK vendor as 15B7

Change : 20752
System : All(Area-51 with Sandisk NVMe P/N Y2HHR)
Impact : Factory,Customer
Modules : disk ePSA/Disk WBBD/do.exe/dowin.exe
Authors : marky
Test #1 : UEFI: run ePSA and "do cdump"
Expect : Verify ePSA [ Storage ] section decodes "OEM: SANDISK, product: A400 NVMe
SanDisk 256GB.."
: not "OEM: 15B7, product: A400 NVMe SanDisk 256GB.." and do cdump output
does a similar decode
Test #2 : WBDD: run disk -conf and "dowin cdump"
Expect : Verify disk -conf decodes "Vendor" as "SANDISK" dowin cdump output does a
similar decode

6100.7
-----------------------------------------------------------------------------------
----------------------------------
Issue : JIT-78525 Update Shoemaker Cables for differences between 2U and 4U
Change : 20725
System : Shoemaker 2U/4U
Impact : Factory,Customer
Modules : Cables
Authors : toddb
Test #1 : cables.exe -conf
Expect : Verify cables output matches configuration for PCIE and GPUs

Issue : FE030216 CDROM Slot 7 conflicts with HDD in Slot when S140 mode only
: Shoemaker CDROM is slot 1 and should be -1
: Set_Features fails due to missing OpenDrive code
Change : 20712, 20734, 20739
System : All(14G)
Impact : Factory,Customer
Modules : Disk
Authors : marky,shuang,toddb,ymb
Test #1 : disk.exe -conf
Expect : Verify any CDROM in 2nd S140 ctlr is Slot 11 (actual AHCI Port 7), or
Slot 10 is in AHCI Slot 6
Test #2 : disk.exe -conf
Expect : Verify Shoemaker CDROM is in Slot -1
Test #3 : N/A
Expect : Verify Set_Features works on inbox driver

Issue : Restrict Helios to show 3 pcie slots.

Change : 20707
System : Helios
Impact : Customer & Factory
Modules : Cables
Authors : rods
Test #1 : Run "cables -conf". Verify Pci slots 1-3 only.

Issue : JIT-84499 [Surveyor] No PCIe Slot5 information under ePSA.

Change : 20699
System : Surveyor
Impact : Customer & Factory
Modules : Cables
Authors : rods
Test #1 : Run "cables -conf". Verify Pci slot 5 shows.

6100.6
-----------------------------------------------------------------------------------
----------------------------------
Issue : BITS353176 and BITS353541 Prevent S/N "" from causing testing and not
reporting a result
Change : 20626,20686
System : All
Impact : Factory,Customer
Modules : Disk
Authors : marky,shuang,toddb
Test #1 : disk.exe -f:5 -mon -xml -o:test.xml
Expect : Verify passes on the exact system in the BITS's

Issue : BITS345396 and BITS345705 Prevent 255 slot numbers on M.2 for
workstations
Change : 20624
System : Workstations(Matira3/5/7)
Impact : Factory,Customer
Modules : Disk
Authors : marky,shuang
Test #1 : disk.exe -conf
Expect : Verify NVMe Slot numbers are not 255 for Matira3/5/7

Issue : BITS351605 M.2 SSD slot detection with iRST driver version 16.0.
Change : 20662
System : All
Impact : Factory,Customer
Modules : Disk
Authors : ymb
Test #1 : disk.exe -ficore -o:test.txt
Expect : Verify IntelDiskId field reports correct information - no multiple
entries with 0-0-0-0, no 255-255-255-255.
Test #2 : disk.exe -conf -o:test.txt
Expect : Verify conf output reports correct information - no multiple entries with
0-0-0-0.

Issue : Refine workaround for FE029842 Trailbreaker2 hang - remove several debug
fMsg's
: and replace with Starting... Closing... Replace removed disk temperatures
and fElapsedTimer thread
Change : 20647
System : All
Impact : Factory,Customer
Modules : Disk
Authors : marky,toddb
Test #1 : disk.exe -f:23 -mon -xml -o:test.xml
Expect : Verify does not hang on a fresh boot in the factory process, on the exact
system in the FE.
Test #2 : disk.exe -f:23 -mon -xml -o:test.xml
Expect : Verify "Total Elapsed Time: HH:MM:SS" is printed on -mon top line again

Issue : Fix FE030106 exception when DST subtest follows a verify subtest
Change : 20647
System : All (With 24 SAS drives on a H730P and two RAID volumes, totoal of 26
devices)
Impact : Factory,Customer
Modules : Disk
Authors : marky,toddb
Test #1 : disk.exe -f:1 -mon -xml -o:test.xml
Expect : Verify the DST subtest does not cause exception for 24 SAS drives

Issue : Add fIsRackMountSystem() to handle Installed Items Check return codes on

Zuma-P
Change : 20630
System : Zuma-P
Impact : Factory, Customer
Modules : Cables
Authors : carl
Test #1 : Cables.exe
Expect : No error that fResults() was not being called when chassis ID code in
SMBIOS type 3 is 0x17 (Rack Mount)

Issue : Fix missing "00:01:14" in -xml output "<Msg>HDD0 (0:1) - ATA DST Long
Passed -Total Time: 00:01:14</Msg>"
Change : 20626
System : All
Impact : Factory,Customer
Modules : Disk
Authors : marky,toddb
Test #1 : disk.exe -f:23 -mon -xml -o:test.xml
Expect : Verify for all HDD's that PASS, the timestamp is printed as described and
not end like "... -Total Time: </Msg>"

6100.5
-----------------------------------------------------------------------------------
----------------------------------
Issue : Workaround - Fix FE029842 Trailbreaker2 hang
Change : 20597,20606
System : All
Impact : Factory,Customer
Modules : Disk
Authors : marky,toddb
Test #1 : disk.exe -f:23 -mon -xml -o:test.xml
Expect : Verify does not hang on a fresh boot in the factory process, on the exact
system in the FE.

Issue : Fix FE029761/FE030012 causing DEFT to log failures on 9311-8i as BI holds

off DEFT and DEFT fw logs a
: a failure as it cannot read enough LBA's in 90 min in order to calculate
an error rate
Change : 20594
System : Servers,Workstations
Impact : Factory,Customer
Modules : Disk
Authors : marky,toddb
Test #1 : disk -f:23 -mon -o:deft.txt
Expect : Verify a RAID 1 can be created on two Seagate SAS P/N 2M5JK drives
connected to a 9311-8i, reboot, and DEFT test #1 passes

Issue : JIT-80490 Run SCSI PT for HBA330 Verify10 and Verify16 instead of using
storlibir3
Change : 20584, 20586
System : All
Impact : Factory,Customer
Modules : Disk
Authors : ymb, marky
Test #1 : disk.exe -f:3 -mon -xml
Expect : Verify all tests run to completion successfully

6100.4
-----------------------------------------------------------------------------------
----------------------------------
Issue : Fix disk -ficore exception on Ducatix AIO with RAID Disabled, and
physical disk + Liteon CACHE
Change : 20553
System : All
Impact : Factory,Customer
Modules : Disk
Authors : marky, ymb, toddb
Test #1 : disk.exe -conf (or disk -ficore)
Expect : Verify no exception occurs

Issue : Fix unreferenced variable for SOS disk build image

Change : 20552
System : All
Impact : Customer
Modules : Disk
Authors : toddb
Test #1 : build SOS image
Expect : Verify no errors

Issue : Add Full support for BOSS HDD flash (FE029978, FE029997) and partial
support for Zoom Slot numbers
Change : 20544 (completes 20525)
System : All
Impact : Factory,Customer
Modules : Disk
Authors : marky, shuangw
Test #1 : disk.exe -hddflash
Expect : Verify BOSS M.2 can be flashed when DELLBOSS volume is created (or if
none exist, too)

6100.3
-----------------------------------------------------------------------------------
----------------------------------
Issue : Add partial support for BOSS HDD flash and Zoom Slot numbers
Change : 20525
System : All
Impact : Factory,Customer
Modules : Disk
Authors : marky, shuangw
Test #1 : disk.exe -conf -o:disk.txt
Expect : Verify Slot numbers for Zoom cards on Matira3, Matira5, AvalonR are
better guesses - but NOT Matira7
Test #2 : disk.exe -hddflash
Expect : Verify BOSS M.2 can be flashed works when no DELLBOSS volume is created.
Still fails when RAID volume is present
Test #3 : disk.exe -f:{N}
Expect : Verify HDD tests still work the same (but with better debug and better
code)

Issue : Add Shoemaker to Motherboard Port Mappings

Change : 20523
System : Shoemaker
Impact : Factory
Modules : Disk
Authors : toddb
Test #1 : disk.exe -conf -o:disk.txt
Expect : Verify Hard drives on first chipset controller show MotherBoardSlot
correctly (0-4) for C1 Shoemaker

Issue : Add DSS 9874G Intel 4TB HHHL card to list

Change : 20517
System : Sandstorm XD
Impact : Factory,Customer
Modules : Disk
Authors : toddb
Test #1 : disk.exe -conf -o:disk.txt
Expect : Verify Part 9874G is HHHL on Sandstorm

Issue : New : Support for Intel driver RSTe 5.3 and NVMe DST.
Change : 20514
System : Matira 3/5/7
Impact : Factory,Customer
Modules : Disk
Authors : ymb
Test #1 : disk.exe -conf -o:disk.txt
Test #2 : disk.exe -ficore -o:disk.txt
Test #3 : disk.exe -f:23 -o:disk.txt
Test #4 : disk.exe -f:7 -o:disk.txt
Expect : Verify Matira ficore, conf output is correct and dst long and short run
if supported.

6100.2
-----------------------------------------------------------------------------------
----------------------------------
Issue : Part4: Change Liqid HHHL P/N 5DH84 from R630 to R640
Change : 20487
System : Pioneer
Impact : Factory,Customer
Modules : Disk
Authors : marky
Test #1 : disk.exe -conf -o:disk.txt
Expect : Verify Liquid is HHHL on Pioneer/R640

Issue : BITS349614 Add newer HDD/SSS/M.2

Change : 20481
System : All
Impact : Factory
Modules : systemConfig
Authors : marky, toddb
Test #1 : systemConfig.exe -sil -o:sil.txt
Expect : Verify all 32 HDD types are reported, not just the 9 it was reporting

Issue : CR: JIT-79746 - Add WBDD version in SIL

Change : 20473
System : All
Impact : Factory
Modules : SystemConfig
Authors : bbw
Test #1 : systemconfig -sil
Expect : confirm XML tag SysConfigVersion is output with build number
Issue : Add Riser2E (DPN HHGW8) to Kepler
Change : 20458
System : Kepler
Impact : Factory,Customer
Modules : Cables
Authors : rods
Test #1 : cables -conf
Expect : Verify new riser translation

Issue : BITS339235 Fix excessive 17 min (1000 sec) timeout

Change : 20451
System : San Bernadino
Impact : Factory,Customer
Modules : Disk
Authors : marky, toddb
Test #1 : disk.exe -conf -o:disk.txt
Expect : Verify disk runs quickly and does not take 17 min

6100.1
-----------------------------------------------------------------------------------
----------------------------------
Issue : Part3: Add support for DSS HHHL Seagate Joplin P/N VTTNM and fix issue
with Liqid HHHL changeset 20361
Change : 20430
System : All
Impact : Factory,Customer
Modules : Disk
Authors : marky, toddb
Test #1 : disk.exe -conf -o:disk.txt
Expect : Verify extra BP's are not added, and Verify Seagate Joplin J 1.6TB P/N
VTTNM is PortCount = 4 and all 4
: NVMe are under same PCIe Bridge Card (Width=HHHL) in a x16 Slot.

Issue : Part2: Add support for DSS HHHL Seagate Joplin P/N VTTNM and fix issue
with Liqid HHHL changeset 20361
Change : 20421
System : All
Impact : Factory,Customer
Modules : Disk
Authors : marky, toddb, ymb, shuangw
Test #1 : disk.exe -conf -o:disk.txt
Expect : Verify Liqid P/N 5DH84 and the M.2 Samsung drives inside it are shown as
HHHL.
Test #2 : disk.exe -conf -o:disk.txt
Expect : Verify Seagate P/N VTTNM and it's M.2 drive inside is shown as HHHL.
Test #3 : disk.exe -conf -o:disk.txt
Expect : Verify both cards in same system are shown as HHHL, under different PCIe
Bridge Card controllers
: and verify both are ControllerInOrExt = External and the Liqid is
PortCount 4, the Seagate is PortCount 1

Issue : Add Config Z2 to Trailbreaker2 cables

Change : 20413
System : Tailbreaker2
Impact : Factory & Customer
Module : cables
Authors : shuangw
Test #1 : Run "cables -conf" on Config B without any GPU unit installed
Expect : Verify SystemConfig is Z2

Issue : FE029682 FSJ CCC Multiplatform-mem\_generic\test.py-Generic,Memory Test

failed
Change : 20381
System : all
Impact : Factory,Customer
Modules : memory
Authors : bbw
Test #1 : run any level memory test of large CPU count system (>32 logical
processors)
Expect : Test should complete normally.

Issue : CR: BITS347131 and JIT-77263 - Add new dynamic algorithm execution option
levels 30 and 31 with algorithm
: execution information output on level 12,13, 30 and 31
Change : 20379
System : all
Impact : Factory,Customer
Modules : memory
Authors : bbw
Test #1 : memory -f:12 or memory -f:13
Expect : Verify memory output also includes test algorithm information
Test #2 : memory -f:30 or memory -f:31 with -algorithms:scan,stress -loopcount:2
Expect : Verify two test algorithm outputs for each of scan and stress algorithms

Issue : Added Shoemaker to Cables

Change : 20369
System : Shoemaker
Impact : Factory,Customer
Modules : Cables
Authors : toddb
Test #1 : cables.exe -conf
Expect : Verify cables output matches configuration

Issue : Add dowin support for "do bios irq", VPD, printing TAG: Ids, and
: VID/formatting updates from do.cpp to be able to compare cdumps in UEFI
and WinPE.
Change : 20366
System : All
Impact : Factory only
Module : dowin
Authors : marky
Test #1 : Boot winPE with latest release
Expect : Verify cdump.bat output is close to cdump.nsh, now both have "do bios
irq" info
Test #2 : find "TAG:" cdump.txt
Expect : Verify Tag list of ids is printed nicely. PCI-X bridges do not have sub-
Ids

Issue : Part1: Add support for DSS un-HHHL Liqid card P/N 5DH84. Liqid MPN LQD-
E1APN04M006T40
Change : 20361
System : All
Impact : Factory,Customer
Modules : Disk
Authors : marky, toddb
Test #1 : disk.exe -conf -o:disk.txt
Expect : Verify Liqid P/N 5DH84 and the M.2 Samsung drives inside it are shown as
HHHL.

Issue : Added what.bat for X:\wbt\RamLibarary\Dellmech WBDD scripts

Change : 20359,20368,20370
System : All
Impact : Factory only
Module : dowin,ReleasePackage
Authors : marky, toddb
Test #1 : Boot winPE with latest release
Expect : Verify what.bat, ip.bat and help.bat and the batches it names work

Issue : FE029685 BTO/FACE System fail on riser 2 detection, however see in BIOS
M.2 card attached to riser.
Change : 20344
System : Helios, Surveyor
Impact : Factory & Customer
Module : cables
Authors : rods
Test #1 : Run "cables -conf"
Expect : Verify Riser2 installed/not is correct.

Issue : FE029639 Disk -stbi on PMC fails and sometimes causes an exception
Change : 20319
System : All with PMC controllers (8805, 8885, etc)
Impact : Factory & Customer
Module : disk.exe
Authors : marky, toddb, ymb
Test #1 : disk -stbi
Expect : Verify disk passes for SAS and SATA drives on a PMC controller

Issue : FE029627 Rickon: Long test for 8TB drive M40TH does not run DEFT
Change : 20313
System : All with PMC controllers (8805, 8885, etc)
Impact : Factory & Customer
Module : disk.exe
Authors : marky, toddb
Test #1 : disk -f:23
Expect : Verify DEFT is run (not DST Long) if the HDD supports DEFT (for SAS&SATA
drives).

Issue : FE029330 disk -conf -xml -o:conf.xml slots 0-3 repeated on Stark
Change : 20311
System : Stark
Impact : Factory & Customer
Module : disk.exe
Authors : marky, toddb
Test #1 : Run "disk -conf"
Expect : Verify 8xNVME report as Slots 0,1,2,3,4,5,6,7 where the motherboard NPIO
use Slots 0..3, the Riser NVMe use 4..7

Issue : Fixed Trailbreaker2 GPU Temp Sensor cables

Change : 20306
System : Tailbreaker2
Impact : Factory & Customer
Module : cables
Authors : shuangw
Test #1 : Run "cables -conf"
Expect : Verify GPUTemp cables work
Issue : FE029566 AHCI HDD runs DST Long when it should run DEFT
Change : 20301
System : All
Impact : Factory
Module : disk
Authors : marky, ymb
Test #1 : disk -f:23 -mon
Expect : Verify DEFT is run (not DST long) on AHCI ctlr for SATA drives that
support DEFT

Issue : FE029323 -ficore intermittent exception.

Change : 20289
System : Pounceport
Impact : Factory
Module : disk
Authors : ymb, marky
Test #1 : disk -ficore
Expect : Verify output does not exit with an exception

Issue : FE029352 Odyssey backplane not seen when installed with Stash
Change : 20287
System : Odyssey
Impact : Factory
Module : disk
Authors : marky, toddb
Test #1 : disk -conf
Expect : Verify output shows Odyssey backplane when installed with Stash sled

Issue : WBDD cmdLine is not in output (unless -xml is used)

Change : 20277
System : All
Impact : Factory
Module : disk
Authors : marky
Test #1 : disk {or any othe WBDD console app, enter any cmdline args} -v -o:out.txt

Expect : Verify out.txt contains the cmdline used near the top of the file after
"CommandLine: "

Issue : FE029323 Disk -ficore exception on PouncePort

Change : 20264
System : All
Impact : Factory
Module : disk
Authors : marky, ymb
Test #1 : disk -ficore
Expect : Verify no exception in USB detection

Issue : Correct reading of TPMID0 bit on New Frontiers

Change : 20247
System : Helios, Kepler, Surveyor
Impact : Factory and Customer
Module : cables
Authors : rods
Test #1 : Run "cables -conf"
Expect : Verify TPM is as expected

Issue : FE028507 HDD flash fails DSL5 to DSL7 for Seagate SAS P/N 7FNRX (same
issue as older ePSPA workaround for 1NFN7)
Change : 20244
System : All
Impact : Factory
Module : disk
Authors : marky, shaung, toddb
Test #1 : flash DSL07.fwh
Expect : Verify DSL5 flashes to DSL7

Issue : BITS343631 and "PCIE SSD can't be detected in Zoom card - JTPTYC2
Change : 20211
System : All
Impact : Factory, Customer
Module : disk
Authors : marky, ymb
Test #1 : Run "disk.exe -conf"
Expect : Verify NVMe drives are not missing, and do not show up as RAID and Not
Applicable

Issue : Add DSS Micron 9100 PRO 3.2TB HHHL SSD P/N RF5FN
Change : 20202
System : All
Impact : Factory, Customer
Module : disk
Authors : marky, ymb
Test #1 : Run "disk.exe -conf"
Expect : Verify card presents as HHHL.

Issue : Add DSS HHHL 0x8086 0x2701 0x8086 0x3904 Intel Optane P4800X 375GB
Change : 20184
System : All
Impact : Factory, Customer
Module : disk
Authors : ymb
Test #1 : Run "disk.exe -conf"
Expect : Verify card presents as HHHL.

Issue : Fixed Trailbreaker2 Riser1 should report as x16x4 slots

Added Trailbreaker2 GPU cables support, and modified the "System Config"
detection
: Fixed potential code issues reported by Coverity static analysis
Change : 20180, 20182, 20219
System : Tailbreaker2
Impact : Factory & Customer
Module : cables
Authors : shuangw, marky
Test #1 : Run "cables -conf"
Expect : Verify riser1, if installed, is x16x4.
Verify System Config is correct, and GPU cables work fine.

Issue : JIT-70735 [Helios Surveyor]-ePSA: "PIB A =Not Installed" & "PIB

B=Installed". They decided to consolidate
: the two signals into just one like Taurus.
Change : 20178
System : Helios/Surveyor
Impact : Factory & Customer
Module : cables
Authors : rods
Test #1 : Run "cables -conf"
Expect : Verify a single PIB shows installed/not correctly.
Issue : FixInt. Fix Genesis GPU1Temp cable detection.
Change : 20173
System : Genesis
Impact : Factory & Customer
Module : cables
Authors : rods
Test #1 : Run "cables -conf"
Expect : Verify the cable shows installed/not correctly.

Issue : Added support usb.bat and help.bat for X:\wbt\RamLibarary\Dellmech WBDD

scripts
Change : 20161, 20170, 20171
System : All
Impact : Factory only
Module : dowin,ReleasePackage
Authors : marky
Test #1 : Boot winPE with latest release
Expect : Verify help.bat and the batches it names work

Issue : JIT-75822,FE029272: hddflash fail P/N 3K30N which does not set
stripHeader bit in NA01/NA02.fwh files
: and Eli Ellsworth GTO request "TO LOG WHETHER A FW FLASH OR SOFTWARE
UPDATE TOOK PLACE AND THE INCOMING AND UPDATED FW"
Change : 20158
System : All
Impact : Factory
Modules : Disk
Authors : marky, toddb
Test #1 : disk.exe -hddflash -o:flash.txt .. and other various args -backflash, -
forceflash.. with P/N 3K30N SAS HDD
Expect : Verify fw can flash back and forth properly.
Test #1 : disk.exe -hddflash -o:flash.txt .. and other various args -backflash, -
forceflash.. with P/N 3K30N SAS HDD
Expect : Verify find "FLASH:" flash.txt {for various cases} produce lines similar
to below. HDD is flashed to EA01 initially.
: Using flash.bat from my S: drive which copes %1 to X: from S: if it
exists and then flashes with -o:flash.txt
: and finally does the find "FLASH:" flash.txt
:
: flash NA02.fwh -backflash
: FLASH: HDD0 (2:1:1) Unsupported: Drive firmware flashing is not supported
(ST1000NX0423)
: FLASH: HDD2 (4:0:1) Unsupported: Drive firmware flashing is not supported
(Dell Express Flash NVMe SM1715 1.6TB SFF)
: FLASH: HDD1 (2:1:2) No Firmware: Current device firmware (EA01)
:
: flash NA02.fwh
: FLASH: HDD0 (2:1:1) Unsupported: Drive firmware flashing is not supported
(ST1000NX0423)
: FLASH: HDD2 (4:0:1) Unsupported: Drive firmware flashing is not supported
(Dell Express Flash NVMe SM1715 1.6TB SFF)
: FLASH: HDD1 (2:1:2) Needs Update: Current device firmware (EA01) to
(EA02)
: FLASH: HDD1 (2:1:2) Verified: (AL14SEB120NY) Firmware (EA02)
:
: flash NA02.fwh
: FLASH: HDD2 (4:0:1) Unsupported: Drive firmware flashing is not supported
(Dell Express Flash NVMe SM1715 1.6TB SFF)
 : FLASH: HDD0 (2:1:1) Unsupported: Drive firmware flashing is not supported
(ST1000NX0423)
: FLASH: HDD1 (2:1:2) No Update: Current device firmware (EA02) is greater
or equal than requested (EA02)
:
: flash NA02.fwh -forceflash
: FLASH: HDD2 (4:0:1) Unsupported: Drive firmware flashing is not supported
(Dell Express Flash NVMe SM1715 1.6TB SFF)
: FLASH: HDD0 (2:1:1) Unsupported: Drive firmware flashing is not supported
(ST1000NX0423)
: FLASH: HDD1 (2:1:2) Forced Update: Current device firmware (EA02) to
(EA02)
: FLASH: HDD1 (2:1:2) Verified: (AL14SEB120NY) Firmware (EA02)
:
: flash NA02.fwh -backflash
: FLASH: HDD2 (4:0:1) Unsupported: Drive firmware flashing is not supported
(Dell Express Flash NVMe SM1715 1.6TB SFF)
: FLASH: HDD0 (2:1:1) Unsupported: Drive firmware flashing is not supported
(ST1000NX0423)
: FLASH: HDD1 (2:1:2) No Firmware: Current device firmware (EA02)
:
: flash NA01.fwh -backflash { note now copies NA01.fwh to X: drive }
: FLASH: HDD0 (2:1:1) Unsupported: Drive firmware flashing is not supported
(ST1000NX0423)
: FLASH: HDD2 (4:0:1) Unsupported: Drive firmware flashing is not supported
(Dell Express Flash NVMe SM1715 1.6TB SFF)
: FLASH: HDD1 (2:1:2) Needs Backflash: Current device firmware (EA02) to
(EA01)
: FLASH: HDD1 (2:1:2) Verified: (AL14SEB120NY) Firmware (EA01)

Issue : BITS332786 - build USBBist (DDUsbDiag.exe) in non-Factory mode so that

the USB driver is not loaded.
Change : 20129
System : All
Impact : Factory, SOS
Modules : USBBist
Authors : carl
Test #1 : factory build : ddusbdiag.exe
Expect : UBIST tests to run on UBIST enabled devices
Test #2 : SOS build : ddusbdiag.exe
Expect : No UBIST tests to run, no UBIST driver loaded, even for UBIST enabled
devices
Test #3 : Full OS build : ddusbdiag.exe
Expect : No UBIST tests to run, no UBIST driver loaded, even for UBIST enabled
devices

Issue : Add new memory test levels to match ePSA tests ending with disk test
Change : 20082
System : All
Impact : Factory
Modules : Memory
Authors : bbw
Test #1 : memory -f:12 or memory -f:13
Expect : verify optional test levels are not run if disk is not running

Issue : FE029178 Fix Slot #s 16..N to map to 0..N on Stark with PMC 8885
Change : 20081
System : All
Impact : Factory,Customer
Modules : Disk
Authors : marky, toddb
Test #1 : disk.exe -conf
Expect : Verify correct slot numbers for PMC 8885 on Stark

Issue : BITS340633 Backout 19500 to HHHL tables to make Samsung SM961 and PM961
devices report M.2 and no HHHL
Change : 20074
System : All
Impact : Factory,Customer
Modules : Disk
Authors : marky, toddb, ymb
Test #1 : disk.exe -conf
Expect : Displays properly for Samsung M.2 devices. (LIQID HHHL P/N 5DH84 will
report M.2 or whatever is in it's M.2 slots)

Issue : Initial Trailbreaker2 Cables. ( GPU cables are commented out )

Change : 20070
System : Trailbreaker2
Impact : Factory,Customer
Modules : cables
Authors : shuangw
Test #1 : run "cables.exe -conf"
Expect : Verify cables work

6099.3
-----------------------------------------------------------------------------------
----------------------------------
Issue : FE029094 Fix missing Backplane on Odyssey
Change : 20027
System : All
Impact : Factory
Modules : disk
Authors : marky,toddb,ymb
Test #1 : disk -conf -v
Expect : Verify backplanes devices are added properly

Issue : Update for 14G SPD format changes. Also distinguish between later 13G and
early 14G formats that used the
: same data format indicator. Change to use DA record for interface address
on 14G and later.
Change : 19987
System : Servers
Impact : Factory
Modules : Eventlog
Authors : rods
Test #1 : Run "eventlog -spdx"
Expect : Verify the SPD can be formatted if SPD contains any OEM data.

Issue : Initialize 32 cDiskDevice member vars and fix a dwBuffSize:-136 issue

Change : 19974,20015
System : All
Impact : Factory
Modules : disk
Authors : marky
Test #1 : disk -conf -v
Expect : Verify "dwBuffSize:-136" is not printed on Matira5

Issue : New. Add support for Pathfinder and Sojourner.

Change : 19968
System : Pathfinder, Sojourner
Impact : Factory & Customer
Modules : cables, SystemConfig
Authors : bbw
Test #1 : Run "systemconfig -noexe -conf"
Expect : Should have one CPLD entry for Pathfinder, two for Sojourner
Test #2 : Run "cables -conf"
Expect : Observe configurations for Pathfinder and Sojourner systems in output.

Issue : JIT-72889 [Kepler] WBDD 6098.7 No riser descriptions

Change : 19941
System : Kepler
Impact : Factory & Customer
Modules : Cables
Authors : rods
Test #1 : cables -conf
Expect : Verify riser shows as NotInstalled or translation.

Issue : Fix last few disk tests for -f:25..-f28 to match documentation in help,
especially for -f:25 Complete DEFT
Change : 19938
System : All (Kenworth, with -d:hdd:1 -d:hdd:2 -d:hdd:3 because -d:hdd:0 has priot
DST failure)
Impact : Factory
Modules : disk
Authors : marky,toddb,ymb
Test #1 : disk -f:24 -o:StartDEFTandExit.txt
Expect : Verify DEFT is started on all drives. If DEFT not supported, they should
run DST Long instead
Test #2 : disk -f:25 -o:CompleteDEFT.txt -t:7200
Expect : Verify DEFT (or DST long if not supported) works on all drives.
: Verify for DST Long, that the test exits after 7200s or 2hrs

6099.2
-----------------------------------------------------------------------------------
----------------------------------
Issue : Remove (PCIe slots %d..%d) after "SAS/PCIe" for Model string os BP for
Dawn.
Change : 19911,19912
System : All
Impact : Factory
Modules : disk
Authors : marky
Test #1 : disk -conf
Expect : Verify as described above
Test #2 : disk -conf -v
Expect : Verify "0xIA64" is not printed

Issue : Correct H&S Riser2 detection. Remove spaces from "Light Bar" xml tag.
Change : 19907
System : Helios, Surveyor
Impact : Factory, Customer
Modules : Cables
Authors : rods
Test #1 : run 'cables -conf'
Expect : config should show correct state of Riser2

Issue : Change fMsg to fDbgMsg to remove "DL: fnd .." lines shown on some configs
(Megatron AHCI)
Change : 19902
System : All
Impact : Factory
Modules : disk
Authors : marky
Test #1 : disk -ficore or disk -conf
Expect : Verify "DL: fnd.." lines are not shown

Issue : Fix Coverity flagged items.

: 13639 cSensor::cSensor cSensor.cpp Resource leak in object
: 13640 cSensor::cSensor cSensor.cpp Resource leak in object
: 13746 fEvlogDimmHandleList(_sLogKey &,unsigned short *) evlog.cpp Out-of-
bounds read
: 13750 fEvlogDehGetNext(int, _sLogKey &, evlogdeh.cpp Out-of-bounds access
Change : 19884
System : All
Impact : Factory,Customer
Module : sensor object, eventlog library
Authors : rods
Test #1 : No specific test. Run modules as normal.
Expect : Normal behavior

6099.1
-----------------------------------------------------------------------------------
----------------------------------
Issue : BITS338140 Matira5 - P/N 29MVR TBT3 card not detected as "AddInDevice"
Change : 19864
System : Matira5
Impact : Factory
Modules : SystemConfig
Authors : marky
Test #1 : systemConfig.exe -conf -o:sysCfg.xml -xml
Expect : Verify <AddInDevice>YES</AddInDevice> is displayed for 8086 15D3 1028
0739 P/N 29MVR TBT3 card

6098.7
-----------------------------------------------------------------------------------
----------------------------------
Issue : BITS336614 Matira3 - Matira3 DVT2: memory test fails in ICC with W-2104
CPU
Change : 19832
System : All that run -f:11
Impact : Factory
Modules : memory
Authors : bbw
Test #1 : run "memory.exe -f:11"
Expect : Should not timeout running tests

Issue : Implement New Frontiers Test Strategy X04 cables definitions

Change : 19819
System : New Frontiers
Impact : Factory,Customer
Modules : cables
Authors : rods
Test #1 : run "cables -conf"
Expect : Verify cable settings

Issue : JIT-69999 and various build verify issues with backplanes

Change : 19816
System : All
Impact : Factory,Customer
Modules : disk
Authors : marky,toddb,ymb,shuangw
Test #1 : disk -conf -o:disk.txt
Expect : Verify PCIE and UNIVERSAL backplanes show up under the PCI Bridge
devices. A Universal BP will be duplicated
: for up to 3 bridges for Horizon.
: Verify "24 x 2.5" SAS/PCIe" (any universal BP) now indicates which slots
are NVMe-capable: "24 x 2.5" SAS/PCIe (PCIe slots 20..23)".
Expect : JIT-69999. Verify HDD S140 drives show up properly on S140 (not missing)
Expect : Verify no Fatal exception on HorizonC3 S140 when -trace -conf is run
Expect : Verify BusType changed from SATA to NVMe for NVMe drives
Expect : Verify workaround for FE028049 on Odyssey (now JIT-67953), which has been
removed, still works when updated to BP fw 4.04 (the real fix)
Expect : Verify IPMI debug messages print ASCII in WBDD instead of printing ????
Expect : Verify SYS_ODYSSEY_FC and SYS_ODYSSEY_VRTX systems report Slot 0 not 2
for chipset HDD's

Issue : Slot 9 changed to Slot 0 on HDD ctlr for Ulysses and SystemConfig does
not show Slot number
Change : 19816
System : Ulysses
Impact : Factory
Modules : SystemConfig
Authors : marky,ymb
Test #1 : run "systemConfig.exe -conf -o:sysCfg.txt"
Expect : Verify Slot number is displayed for PCI device 1000 005F 1028 1F44 or
H330 PERC.

Issue : BITS336351 Matira3 - nVME w/o VROC RAID config, nVMEs are detected to be
"SSD" with WBDD "disk.exe -ficore"
Change : 19806
System : Matira, Pearl, Avalon
Impact : Factory
Modules : disk
Authors : ymb,marky
Test #1 : run "disk.exe -ficore"
Expect : Verify field 3 displays all nvme as "PCIESSD"

6098.6
-----------------------------------------------------------------------------------
----------------------------------
Issue : Ulysses VGA cable not working
Change : 19799
System : Ulysses
Impact : Factory,Customer
Modules : cables
Authors : shuangw
Test #1 : run "cables.exe -conf"
Expect : Verify VGA cable works

Issue : JIT-69097 Build verify fails for NVMe configs for too many backplanes
Change : 19752
System : All
Impact : Factory,Customer
Modules : disk
Authors : marky,toddb
Test #1 : Verify NVMe drives connected to chipset internal PCIe bridges all show up
under 1 PCIe brigge, not many

Issue : FE028548 Reverse (2) CDROM Slot numbering (Added Avalon7 to fix in
FE026814)
Change : 19728
System : Avalon 7
Impact : Factory
Modules : disk
Authors : toddb
Test #1 : disk -conf
Expect : system with 2 optical drives shows correct slot number on Avalon 7

Issue : JIT-69831 [Surveyor]-ePSA: "Riser 1=0x0(Unnown)" shows under

configuration tab with Riser1(DP/N:YTC4M) installed.
: JIT-69654 [Helios Surveyor] BP sequence in ePSA Diag does not match with
common 14G behavor
: JIT-69655 [Helios Surveyor] BP info. shows invalid "Back Plane 2 Power"
in ePSA Diag for front Backplane(12*3.5").
Change : 19722, 19726, 19745
System : New Frontiers
Impact : Factory,Customer
Modules : cables
Authors : rods
Test #1 : Verify epsa -conf and cables -conf show correct Riser and Backplane
presence.

Issue : Remove BOSS power cable from Pioneer

Change : 19720
System : Pioneer
Impact : Factory,Customer
Modules : cables
Authors : marky
Test #1 : Verify "M.2Power" cable is removed from ePSA cables config and cables.exe
-conf output

Issue : BITS325643, BITS329938 : NV6000 video card training error. Exclude TE for
both elements of the card.
Change : 19712
System : Matira 3/5/7
Impact : Factory
Modules : PCIe
Authors : carl
Test #1 : epsa
Expect : No training error displayed for 0x10DE:0x1B30 or 0x10DE:0x10EF

Issue : JIT-67704 Remove bossPres for Odyssey

Change : 19700
System : Odyssey
Impact : Factory,Customer
Modules : cables
Authors : marky
Test #1 : Verify epsa -conf and cables -conf no longer show "M.2" item which is the
BOSS presence.

Issue : Fixed JIT-65751 missing slot 132 in Ulysses due to bus 0x3F was hidden
(solution: unhide all PCI buses)
Change : 19697
System : All (Ulysses)
Impact : Factory,Customer
Modules : PCI
Authors : shuangw
Test #1 : N/A

Issue : FE028292 Use first namespace of NVMe drive to find BytesPerSector to

calculate drive capacity
Change : 19678
System : Grapple
Impact : Factory,Customer
Modules : Disk
Authors : marky, toddb
Test #1 : disk -conf
Expect : Verify system with DSS drive 2Y12T shows correct capacity
Test #2 : disk -f:2
Expect : All tests pass on DSS drive. (Prior version failed Verify test)

6098.5
-----------------------------------------------------------------------------------
----------------------------------
Issue : JIT-69206 Fix -2 slot numbers for Stark - they did not follow 14G mapping
Change : 19646
System : Stark
Impact : Factory,Customer
Modules : Disk
Authors : marky, toddb
Test #1 : disk -conf
Expect : Verify AHCI/S140 slot numbers are 0..N and no negitive values

Issue : FE027317 For LCD brightness setting delay

Change : 19634
System : Client G7/G8
Impact : Factory
Modules : nbpanel
Authors : vinodm
Test #1 : nbpanel -ix
Expect : The brightness test executes successfully

Issue : FE028474 for case with S140 HDD's that broke fix on Pioneer. Add support
for 6 and 7 ODD's on Genesis
Change : 19605,19636,19646
System : Rosetta, Genesis (all S140 14G systems)
Impact : Factory,Customer
Modules : Disk
Authors : marky, toddb
Test #1 : disk -conf
Expect : Verify CDROM Slot is 7 in most cases (6 for BLUE left connector)
Expect : Verify CDROM's move from the 1st S140 to the 2nd S140 ctlr
Expect : Verify 1st S140 is PortCount 6, not 8
Expect : Verify 2nd S140 PCIID, is different from the 1st S140 and correct
Expect : Verify S130/S140 to print "Interface SATA" not "SAS"

Issue : Change name of global to include leading letter "g" for global and keep
local copy of registers on the stack for processing during SMI's
Change : 19603
System : All Client systems
Impact : Factory
Modules : executive
Authors : carl
Test #1 : run any module
Verify : SMI's are working.

Issue : Remove BOSS signals from Cables for Taurus. Signals are not hooked up on
Wave2.
Change : 19600
System : Taurus
Impact : Factory,Customer
Modules : Cables
Authors : rods
Test #1 : cables -conf
Expect : The M.2 devices no longer appear.

Issue : BITS334953 Fix XML tag for LSI SAS9301-16i "APP_ 0.0Rev" should be APPRev
Change : 19596
System : Sideswipe
Impact : Factory,Customer
Modules : Disk
Authors : marky, shuangw
Test #1 : disk -conf -xml
Expect : Verify AppRev is printed not "APP_ 0.0Rev"

Issue : Ulysses renames "Titan Board" to "Control Panel Board"

Change : 19592
System : Ulysses
Impact : Factory,Customer
Modules : Cables
Authors : shuangw
Test #1 : cables -conf
Expect : "ControlPanleBoard" should be "Installed" if either Tiny board or Titan
board is installed.

6098.4
-----------------------------------------------------------------------------------
----------------------------------
Issue : FE028049/JIT-67953 Backplane info is 0 x empty on Rosetta
Change : 19561
System : Rosetta
Impact : Factory
Modules : Disk
Authors : marky
Test #1 : disk -conf
Expect : Verify BackPlane 1 is 2 x 2.5" SAS/PCIe (not 0 x empty)

6098.3
-----------------------------------------------------------------------------------
----------------------------------
Issue : CCC qual build issue: R540 unit with config x8 chassis+ODD ET2 ODD in
S140 mode fails build verify
Change : 19538
System : Rosetta
Impact : Factory
Modules : Disk
Authors : marky
Test #1 : disk -conf
Expect : Verify Rosetta in S140 Mode shows CD-ROM in slot 7 (does not show slot 2)

Issue : FE028172 Correct Exception error with Pearl on 4th NVMe drive with Zoom
4port add in card
Change : 19534
System : Pearl
Impact : Factory
Modules : Disk
Authors : marky, toddb
Test #1 : disk -conf
Expect : No exception error on system with 4 NVMe drives on a Zoom4 card

Issue : FE028403:R540 unit hang on post with BP cable connect error. Engineering
change from BP1/BP2 to BP0/BP1.
: Also update so only R540 has more than 1 BP.
Change : 19531
System : Taurus
Impact : Factory,Customer
Modules : Cables
Authors : rods
Test #1 : cables -conf
Expect : Backplanes BP0 and BP1 are shown.

Issue : FE028308 - fix CPU string output

Change : 19514
System : Cosmos
Impact : Factory
Modules : SystemConfig
Authors : bbw
Test #1 : systemconfig.exe -conf on system with mis-match CPU (Fabric)
Expect : Displays properly for CPU name and version

Issue : Correct HHHL tables and prevent possibility of dl->m_tchProductID

pointing to deleted memory.
Change : 19500
System : All
Impact : Factory,Customer
Modules : Disk
Authors : marky, toddb, ymb
Test #1 : disk.exe -conf
Expect : Displays properly for Samsung HHHL

6098.2
-----------------------------------------------------------------------------------
----------------------------------
Issue : FE028314 Update NVMe, PCIe Addin Bridge, and HHHL discovery
: Add Samsung HHHL cards to list
Change : 19490
System : All
Impact : Factory,Customer
Modules : Disk
Authors : marky, toddb, ymb
Test #1 : disk.exe -conf
Expect : NVME, HHHL are complete and placed under correct controller

Issue : Fixed JIT-65099 missing slot 5 in Taurus by unhiding PCI bus 0x5F
Change : 19468
System : All (Taurus T440)
Impact : Factory,Customer
Modules : PCI
Authors : shuangw
Test #1 : N/A
6098.1
-----------------------------------------------------------------------------------
----------------------------------
Issue : Request for DSS Transactional HHHL NVMe - add PCI ID for Liqid MPN LQD-
E1APN04M006T40
Change : 19453
System : All
Impact : Factory,Customer
Modules : Disk
Authors : ymb
Test #1 : disk.exe -conf -o:disk.txt
Expect : Device recognizes HHHL on a system with Liqid P/N 5DH84.

Issue : JIT-49993 13G - WBDD 6089.8 Reports HDD FW Drive firmware flashing is not
supported
Change : 19451
System : All
Impact : Factory,Customer
Modules : Disk
Authors : ymb
Test #1 : disk.exe -v -HDDFlash -fwDir:X:\DIRECTORY -o:disk.txt
Expect : Does not display unsupported message for PERC recognized as a drive.

Issue : FE028060-Did not find PSU Wattage - 352 in HCF. This is a spec change we
need to update the mask for.
Change : 19406
System : All
Impact : Factory,Customer
Modules : ServerMgmt
Authors : rods
Test #1 : run servermgmt -conf
Expect : Power supply capacity should be able to show more than 2000W.

Issue : FE027975 fix to make it AddIn and also to print Slot's in SystemConfig -
d:misc regardless of AddIn as long as Slot is known
Change : 19399
System : 14G (all wave 1 & 2)
Impact : Factory, Customer
Modules : SystemConfig
Authors : marky, toddb, ymb
Test #1 : SystemConfig -d:misc
Expect : Verify all P/N K5V44 shows all 4 multipfulciont devices as AddIn and all
have Slot #'s

Issue : Add Riser translations for NF cables. Update nvdimm batt "ready" text.
Change : 19393
System : New Frontiers
Impact : Factory,Customer
Modules : Cables
Authors : rods
Test #1 : run cables -conf
Expect : Verify Riser translations are shown if installed. Verify nvdimm battery
ready text is Ready/NotReady.

Issue : FE028028 and other Mercury Slot issues. Mapping Slot#s to -2 in AHCI mode
and fixing -ficore output, too
Change : 19390, 19399
System : 14G (all wave 1 & 2)
Impact : Factory, Customer
Modules : disk
Authors : marky, toddb, ymb
Test #1 : disk -conf and disk -ficore
Expect : Verify all pass mdiag buildverify scripts for various configs

Issue : Rename Ulysses TITAN board, and Front Control Panel cables.
Change : 19365, 19369
System : Ulysses
Impact : Factory,Customer
Modules : Cables
Authors : shuangw
Test #1 : run "cables.exe -conf"
Expect : Verify "TITAN board" and "Front Control Panel" are shown.

Issue : JIT-64747 Missing addin PCIe Bridge Cards and NVMe drive placed under
correct card (Juno)
Issue : JIT-65611 Pioneer showing incorrect slot number for NVMe drive
Change : 19325
System : Juno, Pioneer, Horizon (14G with NVMe)
Impact : Factory Only
Modules : Disk
Authors : toddb,ymb
Test #1 : Run "disk -conf"
Expect : On Juno/Horion Verify Add in PCIe Bridge card(s) are displayed, Correct
number of drives are attached to it
Test #2 : Run "disk -conf"
Expect : On Pioneer verify Slot number is correct for NVMe drives in front
backplane.

Issue : FE027750 DAO-FSJ-A2-BLOCK-MULTIPLATFORM-FSJ Buildverify: systemconfig.exe

missing PCI slot info
Change : 19320
System : SandstormXD, Soundwave
Impact : Factory Only
Modules : SystemConfig
Authors : marky,toddb
Test #1 : Run "systemconfig -noexe -conf"
Expect : Verify P/N C855M Emulex Fibre Channle card shows up as AddInDevice = YES
and has a PCISlot number

Issue : New. Add CPU translations for New Frontiers.

Change : 19312
System : Kepler, Helios, Surveyor
Impact : Factory & Customer
Modules : SystemConfig
Authors : rods
Test #1 : Run "systemconfig -noexe -conf"
Expect : Processor Family and Upgrade should not say unknown.

Issue : New. Initial cables for New Frontiers.

Change : 19307
System : Kepler, Helios, Surveyor
Impact : Factory & Customer
Modules : Cables
Authors : rods
Test #1 : Run "cables -conf"
Expect : Cables display
Issue : Ulysses Fan Type sensor should be 0x40 - 0x47
Change : 19304
System : Ulysses
Impact : Factory,Customer
Modules : Cables
Authors : shuangw
Test #1 : run cables -conf
Expect : Verify "Fan Type" (Standard or Performance) is shown under [ Cables ]

Issue : Workaround. JIT-65179 Remove 14G Ambient/Inlet Sensor Critical Events

from WBDD Fail Conditions
Change : 19301
System : Servers
Impact : Factory
Modules : ServerMgmt, Eventlog library
Authors : rods
Test #1 : Run "servermgmt"
Expect : Should not fail due to Inlet sensor or SEL entry for Inlet sensor.
Test #2 : Run "eventlog"
Expect : Should not fail due to SEL entry for Inlet sensor.

Issue : IT-64747 FE027581 FE027536 FE027434 JIT-62866 Rework PCIe NVMe code for
all known test cases
Change : 19528, 19271
System : Servers and Client
Impact : Factory
Modules : Disk
Authors : marky,toddb,ymb
Test #1 : Run disk -conf on all 14G and 13G systems with NVMe or addIn PCIe
extender cards: 1YGFW, TJCNG, W0DNK, GY1TD, P31H2, NWYNK
Expect : Verify all issues above, disk -conf output is correct for buildVerify.
Pioneer w/o NVMe drives but with NVMe cables will
: not show a "PCIe Bridge Card", but any addIn PCIe extender card *will*
show this Bridge device to insure it is installed.
: Cables -conf can be used to verify PCIe cables are installed for Pioneer.

Issue : JIT-62866. FE027434. FE027446. disk -conf incorrect for NVMe with and
without NVMe drives installed
System : Servers
Impact : Factory
Modules : Disk
Authors : rdb,marky
Test #1 : Run disk -conf on Pioneer / Horizon with NVMe
Expect : Verify NVMe Width is not M.2 for 2.5" NVMe drive
Test #2 : Run disk -conf on Pioneer / Horizon with NVMe cables only (no drives
installed)
Expect : Verify PCI Bridge Card, PCI IDs internal / external are correct
Test #3 : Run disk -conf on Sandstorm with NVMe
Expect : Expect valid conf output

Issue : Fan test method would change from BOX to FINISH LINE on portable systems
and some desktops. Improve data displayed.
System : Client
Impact : Factory
Modules : Fan
Authors : carl
Test #1 : fan.exe
Expect : New data lines showing method being used. Method remains the same for all
speed tests.
Issue : Add new model strings for Stoney Beach and remove device category
checking for Stoney Beach per Simon Kan
System : Client
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a system with Stoney Beach installed run disk -conf
Expect : commodity type to be hard_drive(nvme_m2_upa)

Issue : FE027476: CCC Server 13G SANDSTORM SC9000 buildverify\drive2ctlr\

buildverify.py IOError: Cannot retrieve conf
System : Sandstorm
Impact : Factoy and Customer
Modules : Disk
Authors : rdb
Test #1 : On Sandstorm with 16 QLogic caards and 2 SAS9305 cards run disk -conf
Expect : Valid cof output without exception error

Issue : [JIRA] (JIT-64119) ADC LAB PS3 PILOT 14G W1 BOSS disk.exe -conf -HHHL
extra device detected
System : 14G with BOSS VD
Impact : Factory
Modules : Disk
Authors : rdb
Test #! : on a 14g server with BOSS RAID setup run disk -conf
Expect : DELLBOSS VD to be RAID devicetype
Test #2 : on a 14g server with BOSS RAID setup run disk -ficore
Expect : valid RAID output for DELLBOSS VD device

Issue : JIT-64134 [Mercury] WBDD - Add Sideband Cable Detect

Change : 19159
System : Mercury
Impact : Factory,Customer
Modules : Cables
Authors : bbw
Test #1 : run cables -conf or view ePSA configuration tab
Expect : Entries for SideBand Cable 1 and SideBand Cable 2

Issue : JIT-62866. FE027434. FE027446. disk -conf incorrect for NVMe with and
without NVMe drives installed
Change : 19151
System : Client / Server
Impact : Factory
Modules : disk
Authors : toddb, marky
Test #1 : Run disk -conf on Pioneer / Horizon with NVMe
Expect : Verify NVMe Width is not M.2 for 2.5" NVMe drive
Test #2 : Run disk -conf on Pioneer / Horizon with NVMe cables only (no drives
installed)
Expect : Verify PCI Bridge Card, PCI IDs internal / external are correct

Issue : BITS329575 Limit 2 CDROMs fix to Avalon3 and Avalon 5

: Remove DELLBOSS_VD from disk -conf as a HDD
Change : 19146
System : Client / Server
Impact : Factory
Modules : disk
Authors : toddb, marky
Test #1 : Run disk -conf on Avalon 3/5 with 2 CDROMs
Expect : On our Avalon3 PLDS in Slot 0, TSSTCorp in Slot 1
Test #2 : Run disk -conf on system with BOSS card
Expect : DELLBOSS VD not shown and only 2 Marvel controllers

Issue : SIL Update to support ver 2-10-00 adding TRAINED-SPEED to Memory output
System : All
Impact : Factory
Modules : SystemConfig
Authors : rdb
Test #1 : run systemconfig -sil
Expect : TRAINED-SPEED in Memory section of SIL

Issue : Optane support

System : Client
Impact : Factory
Modules : disk
Authors : rdb
Test #1 : On a system with Optane device run disk -conf
Expect : Correct commodity type in conf output

Issue : Remove all 14G systems from MotherBoardPortMapping as expect SDRGEN to

make Wave 2 the same as Wave 1
Change : 19065
System : 14G (Removed ICE / Genesis)
Impact : Factory
Modules : disk
Authors : toddb
Test #1 : Ice / Genesis with motherboard sata drives run disk -conf and first SATA
drive will show slot 2
Expect : mbslot numbering to be 2 more that displayed on silk screen (0 is 2, 1 is
3, etc.)
: Removes changesets 19011 and 18936

Issue : Tweak decoding of eventlog.exe decoding of iDrac IP for ip.bat to be used

by mdiags
Change : 19063
System : 14G
Impact : Factory
Modules : eventlog
Authors : marky
Test #1 : Run "ip.bat"
Expect : Verify iDrac IP (DHCP or Static) is printed on 13G and 14G. Useful as
often the mdiag
: iDrac port is dedicated and not connected, so they will see 0.0.0.0 and
know to add an
: cable to the iDrac NIC and re-run ip.bat to publish to Delldiag for
faster response to issues

Issue : JIT-62773 CDROM displaying incorrect slot on Ratchet / Shockwave

Change : 19059
System : Ratchet / Shockwave
Impact : Factory & Customer
Modules : disk
Authors : toddb, marky
Test #1 : Run "disk -conf"
Expect : Verify CDROMs display correct slot and motherboardslot. Correct issue
from changeset 18765.
: JIT issues was Ratchet / Shockwave first CDROM should display slot 4 and
was displaying slot 0

Issue : BTO/FACE FE027406 DAO-FSJ-A2-SANDSTORM-SILCollection_Collect Error

System : Server
Impact : Factory
Modules : systemconfig
Authors : rdb
Test #1 : run systemconfig -sil
Expect : Valid SIL output with no exception error

Issue : Remove DSS Brocade 8GB FHHL PCI ID from HHHL table
System : DSS
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : N/A
Expect : N/A

Issue : BTO/FACE FE027406 DAO-FSJ-A2-SANDSTORM-SILCollection_Collect Error

System : Server
Impact : Factory
Modules : systemconfig
Authors : rdb
Test #1 : run systemconfig -sil
Expect : Valid SIL output with no exception error

Issue : JIT-62864 Mercury - WBDD 6096.5 disk.exe -conf has SATA drives starting
at slot0
: JIT-62866 Pioneer - WBDD 6096.5 NVME drive details are missing from
disk.exe -conf output
Change : 19027
System : Servers 14G (Mercury, Pioneer, Horizon)
Impact : Factory
Modules : disk
Authors : marky,toddb
Test #1 : run disk -conf
Expect : Verify NVMe drives are displayed and in the correct slot
Test #2 : run disk -conf
Expect : Verify drives are displayed starting at slot 2 (contrary to cardcage
marking) for Mercury, Horizon and Pearl
: which basically backs out 18838 and 18324 because SDRGEN changed and
thwarted our change.
: Expectiation is they may do this again for Ice and Genesis, too?

Issue : Add DSS Brocade 8GB FHHL PCI ID to HHHL table

System : DSS
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On s system with Brocade 8gB FHHL PCI ID 0x1567 0x0013 0x1567 0x0014 run
disk -conf
Expect : Device to be HHHL

Issue : Update Rosetta riser configuration

Change : 19015
System : Rosetta
Impact : Factory & Customer
Modules : cables
Authors : rods
Test #1 : Run "cables -conf"
Expect : Config includes Riser2 even if Butterfly riser is installed.

Issue : Add Genesis to MotherBoardPortMapping table

System : Genesis
Impact : Factory
Modules : disk
Authors : rdb
Test #1 : On a Genesis with motherboard sata drives run disk -conf
Expect : Correct mbslot numbering

Issue : Use Optane Model string to determine Optane device commodity

System : Client
Impact : Factory
Modules : disk
Authors : rdb
Test #1 : On a system with Optane device run disk -conf
Expect : Correct commodity type in conf output

Issue : JIRA JIT-62395 Mercury - WBDD 6096.4 fan.exe -Tolerance:10 failure

Change : 18989
System : Mercury, Stark
Impact : Factory & Customer
Modues : fan
Authors : rods
Test #1 : Run "fan".
Expect : Fans to show current RPM and perform an event log scan only.

6097.1
-----------------------------------------------------------------------------------
----------------------------------
Issue : Add PCI ID wit DID of 0x2033 for 14G internal PCIe SSD Bridge
System : 14G Servers
Impact : Factory
Modues : disk
Authors : rdb
Test #1 : On a Pioneer and Stark with PCIe Bridge card with PCI ID DID 0x2033
enabled and with BP connected run disk -conf
Expect : PCIe Bridge card ControllerInOrExt tag should be Internal

Issue : Remove Pioneer ssid condition from Internal PCIe SSD Bridge PCI IDs so
all 14G systems will be covered
System : 14G servers
Impact : Factory
Modules : disk
Authors : rdb
Test #1 : On a Pioneer and Stark with PCIe Bridge cards enabled and with BP
connected run disk -conf
Expect : PCIe Bridge card ControllerInOrExt tag should be Internal

Issue : Add exclusion PCIe Training to x8 for 1002:67DF and 1002:AAF0 used on
Alienware Centauri R2 systems
Issue : Add exclusion PCIe Training to x8 for 1002:682B and 1002:AAB0 for the AMD
OPGA13 video card
System : Centauri R2, any system using OPGA13
Impact : Customer
Modules : PCIe
Authors : carl
Test #1 : run PCIe
Expect : No training error for these devices

Issue : JIT-56814 : Stark - WBDD 6096.3 disk.exe -conf has NVME drives attached
to External PCIe bridge card
System : Stark
Impact : Factory
Modules : Disk
Authors : bbw
Test #1 : On a Stark with PCIe SSD Bridge card PCI ID 8086 2030 8086 0000 run disk
-conf
Expect : ControllerInOrExt tag should be Internal

Issue : Add SSD FIPs commodity types for Client

System : All
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : Add SSD FIPS drives to Client system and run disk -conf
Expect : Correct commodity types in output

Issue : Add Driver version information to VROC controller

System : Matira
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : Setup VROC RAID on Matira and run disk -conf
Expect : Driver information output for VROC Controller in conf output

Issue : Add ICE to MotherBoardMappingg table to correct slot numbers

System : ICE
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : fill all slots with drives and run disk -conf
Expect : drives in correct slots

Issue : Correct LOM and ISCSI Mac address displayed

Change : 18919
System : Server
Impact : Factory
Modules : SystemConfig
Authors : marky, toddb
Test #1 : run systemconfig -d:baseboard on system with ISCSI (Pioneer G8RPD)
Expect : Mac Addresses to display correcctly

Issue : Exception error with no HDD Avago config

System : Kenworth
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : run disk -conf on no HDD with Avago controller
Expect : No exception error

Issue : Update MotherBoardMapping structure to have 8 ports

System : All
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : run disk -conf
Expect : valid conf output

Issue : Fix exception error in Ratchet with S130

System : Ratchet
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : Populate all drives in Ratchet, set to SW RAID, set up RAID on drives and
run disk -conf
Expect : Drives should have correct slot numbers and no exception error

Issue : FE027050 - Fix slot numbers for Ratchet with S130

System : Ratchet
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : Populate all drives in Ratchet, set to SW RAID, set up RAID on drives and
run disk -conf
Expect : Drives should have correct slot numbers

Issue : Add StonyBeach check in disk

System : Client
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a system with StonyBeach device that supports Device Category bits
installed run disk -conf
Expect : Commodity to be hard_drive(nvme_m2_upa)

Issue : Optane duplicate function updated to check for physicaldrive string

length greater than 0
System : Sailfish
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a Sailfish with Optane device and using ficore image with Intel Client
Driver 15.5.x.x run disk -conf
Expect : One entry for Optane HDD

Issue : Mercury motherboard slot numbers incorrect

System : Mercury
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : on a Mercury run disk -conf
Expect : HDD motherboard slot numbers to be correct.

Issue : PCIe Cables A0 B0 B1 B1 should use sensors 0xC6, 0xC7, 0xC8, C9.
Change : 18846
System : Ulysses
Impact : Factory & Customer
Modules : Cables
Authors : shuangw
Test #1 : cables -conf
Expect : Verify under [Cables], CablePCIeA0, CablePCIeB0, CablePCIeA1, CablePCIeB1
will show Installed if PCIe cables are physically installed, or vice versa.

6096.3
-----------------------------------------------------------------------------------
----------------------------------
Issue : Fixed Fan test on IPMI chassis systems
Change : 18828
System : Odyssey and other chassis
Impact : Factory & Customer
Modules : Fan
Authors : rods
Test #1 : run "fan".
Expect : Test should show RPMs and scan SEL. Fan control is not available on
these systems.

6096.2
-----------------------------------------------------------------------------------
----------------------------------
Issue : Fixed VROC array output in conf output
System : Matira
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a Matira with 2x Zoom cards with 2 or more M.2 NVMe devices installed
on each card RAID set up on both cards run disk -conf
Expect : All M.2 NVMe devices on each Zoom card should show up under the correct
Zoom card. Each array should show up under the controller. Controller should show
as external.
Note : btoapp112_01sx09 ficore image should be the one used for these configs.

Issue : WindowsSOS system hangs when memory -f:26 is run on Tulip SKL
Change : 18807
System : All
Impact : Customer
Modules : Memory
Authors : bbw
Test #1 : N/A

Issue : EXCALIBUR-1676 WBDD gets exception error, but does not add in the UID for
QRScan code
Change : 18805
System : Customer
Impact : Factory and Customer
Modules : UI
Authors : marky
Test #1 : N/A - no known way to force exception
Expect : If exception occurs with -xml, verify a UID string is added

Issue : Add new function to PciLib to get base address form PCIe configuration
space, and read memory mapped address.
Change : 18798
System : All
Impact : Factory and Customer
Modules : PciLib
Authors : shuangw, marky
Test #1 : N/A

Issue : Update VROC support to work with multiple Zoom cards.

System : Matira
Impaact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a Matira with 2x Zoom cards with 2 or more M.2 NVMe devices installed
on each card and no RAID set up run disk -conf
Expect : All M.2 NVMe devices on each Zoom card should show up under the correct
Zoom card. Controller should show as external.
Note : btoapp112_01sx09 ficore image should be the one used for these configs.

Issue : Update Taurus cables based on new iDrac FW and PT boards. Change BOSS
presence to use sensor. Update Fan
: Type for different sensors. Allow for any legal riser to be installed.
Change BP signals to use sensors.
Change : 18789
System : Ice, Genesis, Rosetta
Impact : Factory & Customer
Modules : Cables
Authors : rods
Test #1 : Run "cables -conf"
Expect : Verify settings are as expected

Issue : JIT-56814 : Stark - WBDD 6093.3 disk.exe -conf has NVME drives attached
to External PCIe bridge card
System : Stark
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a Stark with PCIe SSD Bridge card PCI ID 8086 2031 8086 0000 run disk
-conf
Expect : ControllerInOrExt tag should be Internal

6096.1
-----------------------------------------------------------------------------------
----------------------------------
Issue : FE026814 Reverse (2) CDROM Slot numbering
Change : 18765
System : Avalon 3
Impact : Factory
Modules : disk
Authors : toddb, marky
Test #1 : disk -conf
Expect : system with 2 optical drives shows correct slot number

Issue : Remove Memblaze D750 from HHHL list

Change : 18759
System : DSS
Impact : Factory
Modules : disk
Authors : toddb
Test #1 : disk -conf
Expect : system with part TPH08 (Memblaze D750) shows as SSD drive.

Issue : Fixes invalid Bridge Card PCI ID in disk -conf output

System : Servers
Impact : Factory
Module : disk
Authors : rdb
Test #1 : On a server with add-in bridge card with nvme drive connected run disk -
conf
Expect : valid PCI ID or bridge card and nvme drives

Issue : There is a limit of a count of 8 "missing" fan numbers when discovering

the fans. Needs to be higher than 8.
System : Matira
Impact : Factory and Customer
Modules : Fan
Authors : carl
Test #1 : run fan.exe -conf
Expect : All fans to be discovered and test provided for. Removes the prior
accumulation limit of 8 in the gap count when discovering the fans.

Issue : Added NvmeCompareCommandSupported to disk -conf output for iaRmvd driver.

Do not check NNVME Compare flag. Use
: Identify Data bytes 521:520 BIT0 for Compare flag value per NVME spec.
System : Matira
Impact : Factory
Modules : Disk
Authors : toddb, rdb
Test #1 : run disk -conf on Matira with NVME RAID
Expect : conf output to have NvmeCompareCommandSupported tag

Issue : Set NVME Compare flag to always be true. Fix DST and GList failures
caused by Closed Handles.
System : All
Impact : Factory
Modules : Disk
Authors : toddb, rdb
Test #1 : run disk -f:2 -mon
Expect : All tests pass on all drives.

Issue : FE026657 Slot 5 of 8086.0435 P/N JDVNF was reported as Slot 5 in 6089 but
6094 says Slot 0. Should be Slot 5
Change : 18662
System : All
Impact : Factory & Customer
Modules : pcie
Authors : marky, shuangw
Test #1 : run ePSA or PCIE.exe -conf
Expect : Verify Slot number of JDVNF on PCI Bus supplied by Bridge reporting Slot
0 for that bus, but
: that bridge is in Slot 5, is 5, not 0.

Issue : Added new USB VID:PID for new WWAN/WLAN/Camera modules

(1519:0020,1519:0443,0BDA:58F8)
System : Caracalla, Thanos, Ultron
Impact : Factory
Modules : DDUsbDiag INF and CAT files
Authors : carl
Test #1 : ddusbdiag.exe
Expect : UBIST detection to load the driver for the new VID:PID values.

Issue : Verify NVMe Drive Supports Compare when using RSTe 5.xx iaRVMD driver
Change : 18655
System : All
Impact : Factory
Modules : Disk
Authors : toddb, rdb
Test #1 : run disk -f:1 -v
Expect : NVMe drive runs verify test if SupportsCompare is true

Issue : Remove Device Status Initialization Error Message for disk -ficore -xml
Change : 18638
System : All
Impact : Testing
Modules : Disk
Authors : toddb, marky
Test #1 : run disk -ficore -xml
Expect : No <DeviceStatus>Initialization Error</DeviceStatus> message
Test #1 : run disk -ficore
Expect : Correct output

6095.2
-----------------------------------------------------------------------------------
----------------------------------
Issue : remove LinkRateTest per Jack Kruger HDD team manager
System : servers
Impact : factor
Modules : Disk
Authors : rdb
Test #1 : run disk -f:1 -mon
Expect : no lnkratetest run
Test #1 : run disk -f:2 -mon
Expect : no lnkratetest run

Issue : CR. Requested to remove Boss Power from Juno

Change : 18622
System : Juno
Impact : Factory & Customer
Modules : Cables
Authors : rods
Test #1 : Run "cables -conf"
Expect : Examine output.

Issue : FixInt. Typo in Rosetta riser gpio

Change : 18619
System : Rosetta
Impact : Factory & Customer
Modules : Cables
Authors : rods
Test #1 : Run "cables -conf"
Expect : Examine output.

Issue : FE026585: BTO/FACE � Qual EMFP Mercury - PCI Devices/Cards failed @ QT.
Added 8086 24F0 8086 24F0 to table
System : Mercury
Impact : Factory
Modules : Systemconfig
authors : rdb, bradw
Test #1 : On a Mercury with add-in card with PCI ID 8086 24F0 8086 24F0 run
systemconfig -xml -d:MISC -o:pci.txt
Expect : Add-in card with PCI IC 8086 24F0 8086 24F0 will have AddInDevice tag
value of YES

6095.1
-----------------------------------------------------------------------------------
----------------------------------
Issue : CR. Enhance Eventlog utility to issue Result based on what it finds in
SPD OEM area. This is to support
: future automated scanning of the SPD area where bios and other entities
can record information.
System : All that support SPD read
Impact : Factory
Modules : eventlog
Authors : rods
Test #1 : Run "eventlog -spdx" and examine Result code in message
Expect : PASS - Can read and dump SPD data
: N/A - System does not support SPD
: WARNING - Records in OEM area, but none are errors
: FAIL - Records in OEM area indicate errors were recorded

Issue : Add new DSS HHHL cards for Seagate

System : DSS
Impact : Factory
Modules : disk
Authors : rdb
Test #1 : disk -conf
Expect : system with HHHL cards are detected

Issue : CR. Spec change on how to read CPLD using IPMI commands for 14G.
System : 14G Servers
Impact : Customer & Factory
Modules : Cables
Authors : rods
Test #1 : Run "cables -conf"
Expect : Verify detected settings.

6094.5
-----------------------------------------------------------------------------------
----------------------------------
Issue : FE026360. Prevent extra BP1 device in -conf that is missing Model,Vendor
& FwRev for a Universal front BP.
Change : 18532
System : Servers
Impact : Factory
Modules : disk
Authors : marky,shuang,toddb
Test #1 : run disk -conf
Expect : Verify the correct number of BP's are shown and contain the Model string
with 24 x2.5, etc

Issue : Add support for new WWAN card (DW5816E) and a number of new camera
modules. Used new CAT signing process so these are valid until 4-17-2017.
System : any with the new DW5816E WWAN or any of the new camera's
Impact : Factory
Modules : USBDriver
Authors : carl
Test #1 : ddusbdiag.exe
Expect : Driver to be loaded for DW5816E device and UBIST tests to run.

Issue : Update Customer help for -f:3

System : Client
Impact : Customer
Modules : disk
Authors : rdb
Test #1 : run customer build disk -?
Expect : -f:3 to show as DST Short in help message

Issue : For drives that do not support Defect Lists and return 01/1c/02 in sense
data force GLIST value to 0 and pass test
System : All
Impact : Factory
Modules : disk
Authors : rdb
Test #1 : On a system with OEM HGST drives that do not support Defect Lists run
disk -f:10
Expect : All drives pass List test

Issue : Remove dowin from list of exes systemcomfig calls

Change : 18516
System : All
Impact : Factory
Modules : disk
Authors : rdb
Test #1 : On St Louis run DD Test GUI
Expect : Systemconfig to pass and not have exception error

Issue : SystemConfig generates fatal exception 5

Change : 18514
System : Servers
Impact : Factory
Modules : disk
Authors : marky,toddb
Test #1 : run dowin
Expect : Verify no exception occurs

Issue : Add DST Short Functional Test Block 3 for Customer Release
System : Client
Impact : Customer
Modules : disk
Authors : rdb
Test #1 : run disk -f:3 -mon in Customer release
Expect : expect DST Short test to pass

Issue : Disk code accessing beyond array bounds

Change : 18504
System : Server
Impact : Factory
Modules : disk
Authors : marky, shuang, todd
Test #1 : Not Applicable, no symptoms observed
Expect : Not Applicable, no symptoms observed

Issue : BITS319059, 319063, 319069 - Caracalla LED colors are reverse of

expected. DVT2 board removed inversion requirement of the signal
System : Caracalla - all SKU's
Impact : Customer
Modules : Cables, UI
Authors : carl
Test #1 : run EPSA
Expect : Correct color of the LED during execution and upon completion of the
testing.

Issue : New: CR from Andy Chen to add IntelRAID full drive ID and SED flag to
disk -ficore
System : Client
Impact : Factory
Modules : disk
Authors : rdb
Test #1 : On a Client system with SED drive run disk -ficore
Expect : Last 2 fields in output to have full disk id and SED "n-n-n-n : SED"

6094.4
-----------------------------------------------------------------------------------
----------------------------------
Issue : New Intel Enterprise driver changed the name to iaVROC. Added support.
System : Matira
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On a Matira with RAID set up run disk -conf
Expect : Individual drives to show up under controller

Issue : Modify disk help for Customer builds

Change : 18448
System : All
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : With FACTORY_ONLY set to 0 run disk -?
Expect : Customer build help screen

Issue : Fix command line parameter check for customer/factory settings

Change : 18447
System : All
Impact : Factory & Customer
Modules : Memory
Authors : bradw
Test #1 : With CUSTOMER_ONLY set to 1 run memory -f:25
Expect : Test to pass

6094.3
-----------------------------------------------------------------------------------
----------------------------------
Issue : Add new DSS HHHL card for Micron
System : DSS
Impact : Factory
Modules : disk
Authors : rdb
Test #1 : disk -conf
Expect : system with HHHL cards are detected

Issue : Remove bossPres from most 14G platforms as it does not work
Change : 18419
System : 14G (Horizon/Pearl, Juno, Pioneer, Ulysses, only)
Impact : Factory & Customer
Modules : Cables
Authors : marky
Test #1 : Run ePSA and/or eun "cables -conf"
Expect : Verify "M.2" BOSS presence is not displayed (M.2Power, M.2Drive1,
M.2Drive2 cables unchanged)

6094.2
-----------------------------------------------------------------------------------
----------------------------------
Issue : Exception error occurs in disk due to unitialized variable in VROC class
System : All
Impact : Factory & Customer
Modules : disk
Authors : rdb
Test #1 : run disk -conf
Expect : Valid output

6094.1
-----------------------------------------------------------------------------------
----------------------------------
Issue : Add RSTe/VROC NVMe RAID support
System : Client
Impact : Factory and Customer
Modules : disk
Authors : rdb
Test #1 : On a Matira with VROC enabled and NVME drives set in a RAID run disk -
conf
Expect : IntelVMD controller with NVME drives under it
Test #1 : On a Matira with VROC enabled and NVME drives set in a RAID run disk -f:5
-mon
Expect : All tests pass

Issue : Initial Odyssey,Odyssey_VRTX,Odyssey_FC cables based on Test Strategy

spreadsheet.
System : Odyssey,Odyssey_VRTX,Odyssey_FC
Impact : Factory & Customer
Modules : Cables
Authors : bbw
Test #1 : Run "cables -conf"
Expect : Examine output

Issue : New - Add support for obfuscated QR scancode URL in WBDD console apps
Change : 18323
System : All
Impact : Factory & Customer
Modules : Exec
Authors : marky, shuangw
Test #1 : Run WBDD console app -xml and get a failure
Expect : Verify <UID> tag prints some random ASCII string and that SupportAssist's
GUI can decode to URL

Issue : Initial Taurus cables based on Test Strategy spreadsheet.

System : Taurus
Impact : Factory & Customer
Modules : Cables
Authors : rods
Test #1 : Run "cables -conf"
Expect : Examine output

Issue : Update MotherBoardMapping function and table to handle multiple

controllers
System : Horizon, Pearl
Impact : Factory and Customer
Modules : disk
Authors : rdb
Test #1 : On a Pearl with drives in both bays, run disk -conf
Expect : MotherBoardslot numbers and DriveChannelID to match bay slots. Slot
number will match port number.

Issue : Change DeviceName for Customer builds

System : All
Impact : Customer
Modules : disk
Authors : rdb
Test #1 : Run customer build disk -f:1 -d:hdd:0
Expect : Device name to be HDD0 with no controller:port qualifier [HDD0 (0:0)]

Issue : Add support for Ulysses cables.

: Modified Quick Sync cable detection for 14G (only detect Quick Sync
cable. 14G doesn't have Bezel).
Change : 18298, 18336
System : Servers 14G
Impact : Factory & Customer
Modules : Cables
Authors : shuangw
Test #1 : Run "psa -wait -result" on Ulysses
Expect : Check configuration output tab for proper cable signals for platform.
Test #2 : Run "psa -wait -result" on 14G which has QuickSync cable detection (eg.
Horizon, Pioneer, Juno, Ulysses, etc).
Expect : Verify "iDRAC QuickSync Assembly" is "Installed" if the Quick Sync SKU is
installed. Otherwise, it's "Not Installed" if the LED only SKU is installed.

6093.3
-----------------------------------------------------------------------------------
----------------------------------
Issue : Add flushcache and stbi commands for marvel BOSS card
System : 14G
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On system with BOSS card run disk -flushcache
Expect : pass
Test #2 : On system with BOSS card run disk -stbi
Expect : pass

Issue : FixExt - BITS313013 Correct changeset 16774 which broke running

DDUSBDiag.exe in WinPE
Change : 18246
System : All
Impact : Factory
Modules : WinGUI
Authors : marky, shuangw, Carl
Test #1 : wingui -v2 DDUSBDiag.exe
Expect : Verify DDUSBDiag.exe tests run in WinPE, and do not run in OS

Issue : 14G Cables updates

: 1. Add Fan Status to show Standard/Performance - Pioneer/Horizon only
: 2. Update preliminary Taurus definitions
: 3. Rename SYS_TAURUS_nU to Ice/Genesis/Rosetta
: 4. Add showing cpld revs to Horizon and Pioneer
: 5. Fix cpld maintenance revision
: 6. Update IPMI/PCI debug message
System : 14G Servers
Impact : Factory & Customer
Modules : Cables
Authors : rods
Test #1 : Run "cables -conf"
Expect : Examine output for Fan Status.

Issue : Add current loopcnt to WBDD modules when looping

Change : 18246
System : All
Impact : Factory
Modules : Executive
Authors : marky, shuangw
Test #1 : cables or cables -l:1
Expect : Run test once, does not print loop count
Test #2 : cables -l:2
Expect : Runs test twice, print loop 1 of 2, then 2 of 2
Test #3 : cables -l:0
Expect : Runs test infinitely, print loop 1 of 0, then 2 of 0, ...

Issue : Updates to Dell dimm decoding

: 1. Add 3 dimmPerNode support
: 2. Consolidate Dell memory decoding into single routine
: 3. Consolidate select ePSA/WBDD smbios routines into single source
: 4. Add support for "Gen"eration when reading SEL data from a file
: 5. Remove 12G extended group scheme (bios did not implement)
System : Servers
Impact : Factory & Customer
Modules : Eventlog, evlog library, ipmi library, smbios library
Authors : rods
Test #1 : Run eventlog/memory
Expect : Any failing dimms should be decoded correctly

6093.2
-----------------------------------------------------------------------------------
----------------------------------
Issue : Add on-board Pioneer PCIe SSD Bridge Card to fIsInternalController()
System : Pioneer
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a Pioneer with PCIe SSDs connected to on-board bridge card run disk -
conf
Expect : Controller to be Internal

6093.1
-----------------------------------------------------------------------------------
----------------------------------
Issue : Add Support for Stark system (DSS9600M)
Change : 18180
System : 14G
Impact : Factory & Customer
Modules : Cables
Authors : bbw
Test #1 : Run cables -conf on Stark system
Expect : Confirm output of proper cable signals for platform

Issue : Modified Quick Sync Bezel detection (Unverified)

Change : 18174
System : Servers 14G
Impact : Factory & Customer
Modules : Cables
Authors : shuangw
Test #1 : N/A ( since 14G IPMI for Quick Sync Ear/cable and Bezel is not quite
working yet. This change is made to match 13G )

Issue : Pioneer 2.5" BP not in Disk -conf

System : Pioneer
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a Pioneer with 2.5" rear expander run disk -conf
Expect : 2.5" BP in conf

Issue : Add Support for Marvel BOSS Card

Change : 18160
System : 14G
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : Add BOSS card to 14G server and run disk -conf
Expect : Marvel controller and drives in conf output
Test #2 : Add BOSS card to 14G server and run disk -f:2 -mon
Expect : All tests pass

6092.6
-----------------------------------------------------------------------------------
----------------------------------
Issue : FE025983 Fix exception in disk -ficore
Change : 18126
System : 13G Ratchet, Sandstorm XD
Impact : Factory (FICore)
Modules : Disk
Authors : marky,toddb
Test #1 : disk -ficore
Expect : No exception, normal output

Issue : Cables changes to expose IDSDM and vFlash and correct Unknown 0x3.
Change : 18125
System : 14G
Impact : Factory
Modules : Cables
Authors : marky,toddb
Test #1 : cables -conf
Expect : Verify 3 line are output after Persistent Storage line even if
IDSDM/vFlash are not installed. Changed + to _ for mdiag parsing

Issue : WorkAround for older BIOS that has 19[x] CPU production indicator strings
that are not correct. Use
: internal table before trying for smbios strings.
System : Any, found on Shockwave
Impact : Factory & Customer
Modules : SystemConfig
Authors : rods
Test #1 : Run "systemconfig -conf -noexe -o:xx.txt"
Expect : Examine CPU entries to ensure Production indicator is as expected.

Issue : Initial check-in of AddInCards.ini and AddInCards.txt for HHHL device

support
System : DSS
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : run dis -conf with HHHL card installed where PCIID is in AddInCards.ini
Expect : Width of device is HHHL
//Rollback - removed until later
//Issue : Add Support for Marvel BOSS Card
//Change : 18110
//System : 14G
//Impact : Factory & Customer
//Modules : Disk
//Authors : rdb
//Test #1 : Add BOSS card to 14G server and run disk -conf
//Expect : Marvel controller and drives in conf output
//Test #2 : Add BOSS card to 14G server and run disk -f:2 -mon
//Expect : All tests pass

Issue : Fixed issue created by changing subvendor and subdeviceid placement in

Intel Controller PCI ID string
System : All
Impact : Factory and Customer
Modules : Disk
Authors : rdb
Test #1 : run disk -conf on system with Intel controller and optical device
Expect : optical device to be under INTELRAID controller and have correct slot
number

Issue : Fixed the -f:N option for video memory test level and iteration, and
modified the help msg.
Fixed code bug to compare wide character for "video -rgb -
colors:wrgbcym".
Change : 18092
System : All
Impact : Factory & Customer
Modules : Video
Authors : shuangw, marky
Test #1 : run "video -f:14", and "video -f:61"
Expect : Verify error message is shown saying "Invalid iteration or test level
selected.
Test #2 : run "video -f:xy", where x should be an integer between 0..5, and y
should be between 0..3.
Expect : Verify video memory test runs properly. (The memory test and iteration
times depend on x and y)
Test #3 : run "video -rgb -colors:wr".
Expect : Verify video color test runs for white and red color.

Issue : Correct IRQ Routing table entries Slot 1: Tag FFF8, Slot 2: Tag FFF8, and
Slot 1: Tag FFFA
Change : 18090
System : All (Mdiag T430 serviceTag DTFJF42)
Impact : Factory
Modules : SystemConfig
Authors : marky
Test #1 : systemconfig.exe -conf -noexe -xml -o:output.xml
Expect : No <PciSlot>1<PciSlot> values for embedded PCI devices (at tags FF7C,
FF7D & FF7E)

Issue : Exception error occurring when invalid character in AddInPciCards.ini

System : All
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : run disk -conf with invalid character in AddInPciCard.ini file
Expect : no exception error
Issue : Hide Factory Functional Test Blocks and expose limited Functional Test
Blocks for Customer release
System : All
Impact : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : Run disk -f:1 in customer release
Expect : All tests pass
Test #2 : Run disk -f:2 in customer release
Expect : DST Long runs and passes

6092.5
-----------------------------------------------------------------------------------
----------------------------------
Issue : Cables update for Mezzanine slot and SideBand Cable
Change : 18051
System : Pounceport
Impact : Factory & Customer
Modules : Cables
Authors : toddb
Test #1 : run cables -conf
Expect : Verify Mezzanine and Sideband cable configuration is correct

Issue : Correct subvendor and subdeviceid placement in Intel Controller PCI ID

string
System : All
Impact : Factory
Modules : disk
Authors : rdb
Test #1 : On a system that has HDDs connected to Intel controller run disk -ficore
Expect : ControllerPciId in HDD output to be 8086xxxx1028xxxx

Issue : Remove SPACE in "Not Installed" for Mdiags to be consistent, in cables

XML data value output
Change : 18037
System : 14G
Impact : Factory
Modules : cables
Authors : marky
Test #1 : cables -conf
Expect : Verify any item not installed shows as "NotInstalled"

6092.4
-----------------------------------------------------------------------------------
----------------------------------
Issue : Add two HDDs to Max Link Rate Table
System : Servers
Impact : Factory
Modules : disk
Authurs : rdb
Test #1 : On a system with Intel SSDSC2BA100G3T drive run disk -f:1 -mon
Expect : All tests pass

6092.3
-----------------------------------------------------------------------------------
----------------------------------
Issue : Add Max Link Rate Table and function for drives that report incorrect Max
Link Rate
 : FE025496 BTO/FACE � CCC FSJ GENCO R620 XL & APCC R820 HDD0 link Rate test
fail
System : Servers
Impact : Factory
Modules : disk
Authurs : rdb
Test #1 : On a system with Intel SSDSC2BA100G3T drive run disk -f:1 -mon
Expect : All tests pass

6092.2
-----------------------------------------------------------------------------------
----------------------------------
Issue : Add new DSS HHHL cards for Samsung, Memblaze, Greenliant and Techman
Change : 17964
System : DSS
Impact : Factory
Modules : disk
Authors : toddb
Test #1 : disk -conf
Expect : system with HHHL cards are detected

Issue : Horizon with 3 BP's and BIOS 0.3.4 reports 163 $PIR entries causing an
exception in systemConfig -conf
Change : 17937
System : Horizon
Impact : Factory
Modules : systemConfig
Authors : marky
Test #1 : systemConfig -conf
Expect : Verify exception does not occur on mdiags system described above

Issue : Horizon Riser 1D added missing support. JIT-48621

Change : 17916
System : Horizon
Impact : Factory & Customer
Modules : Cables
Authors : marky
Test #1 : run cables -conf and ePSA
Expect : Verify Riser 1D configuration shows "x16x8x8" not "0x6 (Unknown)"

6092.1
-----------------------------------------------------------------------------------
----------------------------------
Issue : Fix invalid XML when cables fAddChild is used to indent text. Don't add
SPACES for .xml file only.
Change : 17898
System : Servers 14G
Impact : Factory & Customer
Modules : cables
Authors : marky
Test #1 : cables -conf -xml -o:cables.xml
Expect : Verify cables.xml is valid XML by "start cables.xml" and browser displays
correctly
Test #2 : cables -conf -o:cables.txt (and run ePSA)
Expect : Verify ePSA screen, output file, and cables.exe cables.txt all show non-
XML fAddChild lines indented with SPACES as expected

Issue : Pioneer Riser PCIE slot configuration changed with CPLD 0.4.0
Change : 17884
System : Pioneer
Impact : Factory & Customer
Modules : Cables
Authors : toddb
Test #1 : run cables -conf
Expect : Verify Riser configuration is correct especially for Riser 2 showing
correct PCIE slot (2 or 3)

Issue : Add new API files for RAIDCore that support S110,S130 and S140 SWRAID
System : Servers
Impact : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : On a syerver with SWRAID run disk -conf
Expect : Correct conf output

Issue : Add support for RSTe 5.0 SATA

System : Workstations
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On a system booted to image with RSTe 5.0 driver run disk -conf
Expect : Valid conf output with drives under INTELRAID controller

Issue : Add support for NV-DIMM in disk -conf

System : Servers
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a system with NV-DIMM run disk -conf
Expect : HDDNVDIMM to be in disk -conf output

Issue : Add support for DSS booking.com Mangstor 12/24 M.2 cards
System : DSS
Impact : Factory & Customer
Modules : disk
Authors : rdb
Test #1 : On a booking.com system run disk -conf
Expect : M.2 devices to be specified and with correct slots

Issue : Fix PCI Slot reported for Mangstor SSD with 12 M.2 NVMe cards, the first
of which is programmed for Slot 0
Change : 17737
System : Servers (Trailbreaker)
Impact : Factory & Customer
Modules : disk
Authors : marky, toddb
Test #1 : run EPSA -conf or PCIe -conf
Expect : Verify Bus 5 Tag 500 device is reported at Slot 0 (not Slot 4), and Bus
84 Tag 8400 also reports Slot 0, not 6

Issue : Add CPU Production detection for Intel Kaby Lake i7 CPU
System : Kaby Lake i7 based
Modules : systemconfig
Authors : carl
Test #1 : systemconfig.exe
Expect : Production CPU to show it is a production level part instead of "UNKNOWN"

6091.3
-----------------------------------------------------------------------------------
----------------------------------
Issue : Some cables.exe lines print "NotInstalled" and some print "Not Installed"
Change : 17664
System : All
Module : cables
Authors : marky
Test #1 : run cables -conf
Expect : All "Not Installed" strings should be "NotInstalled"

6091.2
-----------------------------------------------------------------------------------
----------------------------------
Issue : Add Intel P3520 HHHL support
System : DSS
Module : disk
Authors : rdb
Test #1 : run disk -conf
Expect : Width to be HHHL for device

Issue : FE025307 Kenworth failed 12Gbps SAS drives because expander limits to
6Gbps
Change : 17643
System : Kenworth, Pounce, PouncePort
Module : disk
Authors : marky, toddb, rdb
Test #1 : disk -f:2
Expect : Verify Link test passes on Kenworth with 12Gbps HDD's

6091.1
-----------------------------------------------------------------------------------
----------------------------------
Issue : Update Pioneer Cables for Riser Cards and SAS cables
Change : 17631
System : 14G Pioneer
Module : cables
Authors : toddb
Test #1 : run ePSA or Cables -conf
Expect : Verify cables output is correct, and especially for Riser cards and SAS
cables

Issue : Add External/Internal controller to ficore output for RAID volume when
available
System : Servers
Impact : Factory
Modules : Disk
Authors : Roger
Test #1 : On a server with H730 with RAID run disk -ficore
Expect : H730 PCIID and external in ficore output

Issue : Fix default backplane displayed to be BP1 not BP0

Change : 17581
System : 14G Horizon
Module : cables
Authors : marky
Test #1 : run ePSA or Cables -conf
Expect : Verify cables output is correct, and especially Backplane1 is shown on
most configs as installed
Issue : Added Tobi Eye camera VID:DID of 2104:010A. This is for Cassini 17
configuration now using this camera.
System : Cassini 17
Impact : Factory
Modules : DDUSBDiag.exe
Authors : carl
Test #1 : ddusbdiag.exe
Expect : Test to install the driver for the Tobi Eye camera with VID:DID of
2104:010A

Issue : Update drive capacity +1 (JIT-30343)

System : Server
Impact : Factory
Modules : Disk
Authors : toddb
Test #1 : Run "disk -conf".
Expect : 300GB SAS drive would display 299999MB, should now display 300000MB

Issue : Add Lucy CPLD to Cables configuration.

System : Lucy
Impact : Factory & Customer
Modules : Cables
Authors : rods
Test #1 : Run "cables -conf".
Expect : Verify CPLD version is shown.

Issue : FE025162 BTO/FACE � Pilot-EMFP-13G-EQUINOX2- Buildverify ControllerHDD

AND RMSD - KeyError pciid
System : Equinox
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a system with HHHL card and no standard NVMe drives run disk -conf
Expect : No stand-alone PCIe-Bridge-Card with no NVMe devices

Issue : Fixed Lucy Cables for PSU1/2

Change : 17527
System : Lucy
Impact : Factory & Customer
Modules : Cables
Authors : shuangw marky
Test #1 : Run "psa -wait -result" with both power supplies and cords connected.
Expect : Verify both power supplies are Installed under [ Cables ].
Test #2 : Run "psa -wait -result" with one of the power cord disconnected, but the
power supply unit connected.
Expect : Verify the Power Supply with power cord disconnected is Not Installed
under [ Cables ].
Test #3 : Run "psa -wait -result" with one of the power supply unit disconnected.
Expect : Verify the Power Supply with power supply unit disconnected is Not
Installed under [ Cables ].

Issue : Lucy reads CPLD version

Change : 17488, 17489, 17490, 17511, 17541
System : Lucy
Impact : Factory & Customer
Modules : IPMI
Authors : shuangw marky
Test #1 : Run "Eventlog -conf".
Expect : Verify CPLD version is shown.
Issue : New support for Mercury (C6420) system
System : Mercury
Impact : Factory
Modules : Cables
Authors : bbw
Test #1 : run cables.exe
Expect : Expect to see supprot for Mercury system in output

6090.2
-----------------------------------------------------------------------------------
----------------------------------

Issue : Add new camera ID's 0x0BDA:5650 ot 565F

System : Any using this camera VID:DID range
Impact : Factory
Modules : DDUSBDiag
Authors : carl
Test #1 : run ddusbdiag.exe
Expect : USB driver to load for the new camera range and UBIST tests to be
detected and executed.

Issue : Invalid logic to determine external or internal controller in disk -

ficore output
System : All
Impact : Factory
Modules : disk
Authors : rdb
Test #1`: run disk -ficore
Expect : Controller PCI ID and Exteranl/Internal fields will be displayed in last
2 fields of the output.

Issue : Lucy Cables Update

Change : 17448
System : Lucy
Impact : Factory & Customer
Modules : Cables
Authors : shuangw
Test #1 : Run "cables -conf", "cables", and "Eventlog -conf".
Expect : Verify Cables tests pass, and Cables and Eventlog outputs are correct.

Issue : Check smbios for CPU Production indicators before using MSR method.
System : All
Impact : Factory
Modules : SystemConfig
Authors : rods
Test #1 : Run "systemconfig -conf"
Expect : Check the Production bit in each CPU entry for other than "unknown".

Issue : Error arguments do not match print format string

Change : 17428
System : All
Impact : Factory
Modules : Disk.exe
Authors : marky
Test #1 : Run various disk cmd lines
Expect : If fDiskError(TST_ERR_SAS_SEQSEEK_FAILURE...) ever occurs, it will not
pop garbage off the stack
Issue : Update to 17169. Spec change for SPD bios log checksum and svctag.
System : 14G Servers
Impact : Factory
Modules : Eventlog
Authors : rods
Test #1 : Run "eventlog -spdx"
Expect : If the dimm contains a BIOS logged error, it should be formatted.

Issue : Lucy video test fails

Change : 17423
System : Lucy
Impact : Factory & Customer
Modules : Video
Authors : shuangw
Test #1 : Run "video.exe" on Lucy
Expect : Verify the video test passes

6090.1
-----------------------------------------------------------------------------------
----------------------------------

Issue : Pioneer Cables Update

Change : 17406
System : Pioneer
Impact : Factory & Customer
Modules : Cables
Authors : toddb
Test #1 : Run "cables -conf"
Expect : Settings for intrusion, power supply and backplane should be as expected
depending on configuration

Issue : SystemConfig updates. Add new Skylake CPU. Add new smbios cpu upgrade
definitions. Fix cpu status.
Change : 17402
System : 14G servers
Impact : Factory
Modules : SystemConfig
Authors : rods
Test #1 : Run "systemconfig -conf"
Expect : Settings for CPU Production, Upgrade, Status should be filled in.

Issue : TRD 0.8 tweaks for Juno cables.

Change : 17394
System : Juno
Impact : Factory & Customer
Modules : Cables
Authors : rods
Test #1 : Run "cables -conf"
Expect : Settings should be as expected depending on configuration.

Issue : Add 2 fields in disk -ficore output for O/S placement help
System : All
Impact : Factory
Modules : disk
Authors : rdb
Test #1`: run disk -ficore
Expect : Controller PCI ID and Exteranl/Internal fields will be displayed in last
2 fields of the output.
Issue : Add access classes for "I/O" and "PCI" to the 14G cables classes.
System : Any
Impact : Factory and Customer
Modules : Cables
Authors : rods
Test #1 : No specific test - classes will be used in future support.

Issue : Update to 16740 - Add NVDimm indicator to memory configuration. BIOS is

now setting industry standard
: bit in TypeDetail field so replace SPD read with that.
Change : 17362
System : Any
Impact : Factory and Customer
Modules : Memory
Authors : rods
Test #1 : Run "memory -conf" with an nvdimm installed.
Expect : The type detail of nvdimm should include the NonVolatile status.

Issue : USB card shows up as not being Add-In when it should show as ADD-IN
(1B21-1242-1B21-1242)
System : Sailfish, Blackfish
Impact : Factory
Module : SystemConfig
Author : carl
Test #1 : systemconfig.exe
Expect : Add in card with 4-part ID of 1B21-1242-1B21-1242 to show as an ADD-IN
card

Issue : Add support for Class 35 M.2 Nvme SED and non-SED commodity type
System : Client
Impact : Factory
Module : Disk
Author : rdb
Test #1 : On system with M.2 Class 35 Nvme SED run disk -conf
Expect : Expect commodity type hard_drive(nvme_m2_sed_P32)
Test #2 : On system with M.2 Class 35 Nvme non-SED run disk -conf
Expect : Expect commodity type hard_drive(nvme_m2_P32)

Issue : Enable factory script usage by allowing log/spd clear to be optional.

Ensure all operations have output
: lines in case user invokes more than one function.
Change : 17318
System : All Servers
Module : Eventlog
Authors : rods
Test #1 : Run "eventlog -clear:all -spdclr -optional".
Expect : Logs/Spd should be cleared if available. If not, test should PASS. If
there is an actual failure, that
: should be reported and the test FAIL.

Issue : Add support for Compal BMC fans (Lucy). Reorganize cFanIPMI to make
adding future systems easier - now
: supports iDrac, Compal, and generic (non-testable).
Change : 17304
System : All Servers
Module : Fan
Authors : rods
Test #1 : Run "fan -conf".
Expect : Fans should show correctly.
Test #2 : Run "fan".
Expect : Fans should test correctly - new support on Lucy.

Issue : [JIRA] (JIT-37815) [Horizon/Pearl] Execute ePSA encounter CABLE ERROR in

X01. The IPMI sensors are disabled
: by iDrac if they don't apply to the config so treat them as not
installed.
Change : 17298
System : 14G Servers
Impact : Factory & Customer
Modules : Cables
Authors : rods
Test #1 : Run "cables -conf".
Expect : None of the items should say "Unknown".
Test #2 : Run "cables".
Expect : Test should Pass.

Issue : Add showing Bios and iDrac version info to Cables configuration.
Change : 17295
System : Servers
Impact : Factory & Customer
Modules : Cables
Authors : rods
Test #1 : Run "cables -conf"
Expect : Bios version number should be shown. If the system has an iDrac, it
should have a line showing it.

Issue : Add support for post-RST NVLINK Config J and K for Trailbreaker
Change : 17287
System : Trailbreaker, Horizon
Modules : Cables
Authors : marky
Test #1 : Run ePSA/Cables.exe on Trailbreaker
Expect : Verify NVLINK Config J and Config K report properly
Test #2 : Run ePSA/Cables.exe on Horizon
Expect : Verify bp3power cable is removed and Cable PCIe A,B,C,D change to
A0,A1,B0,B1,A2,B2

Issue : Centauri displaying same drive twice in disk -conf

System : Centauri
Impact : Factory
Module : Disk
Authors : rdb
Test #1 : run disk -conf on Centauri
Expect : the correct number of drives to be displayed

Issue : BITS302305 - add Chicony camera USB ID's for USB driver.
Change : 17230
System : Aventador
Impact : Factory
Module : DDUsbDiag.exe
Authors : carl
Test #1 : run DDUsbDiag.exe
Expect : New Chicony ID's in the range of 0BDA:5690 to 0BDA:569F to be found and
tested.

Issue : Aventador - touchpad test not working

Change : 17219
System : Aventador
Impact : Factory
Modules : Touchpad
Authors : Cooper
Test #1 : run touchpad.exe -o:test
Expect : test needs to run and show results in output file

Issue : Avalon-R fails IDE-DIAG

System : Avalon-R
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : run disk -f:5 -mon
Expect : All tests pass

Issue : Initial Taurus cables implementation. Not yet complete - no HW

available.
Change : 17203
System : Ice, Rosetta, RosettaXD, Genesis
Impact : Factory & Customer
Modules : Cables
Authors : rods
Test #1 : Run "cables -conf"
Expect : Verify the settings are as expected.

Issue : Update Juno cables. Replace sensors with cpld/spix where possible.
Simplify bit mask terminology.
Change : 17202
System : Juno
Impact : Factory & Customer
Modules : Cables
Authors : rods
Test #1 : Run "cables -conf"
Expect : Verify the settings are as expected.

Issue : Add ability to clear OEM SPD area from all dimms to Eventlog
Change : 17191
System : All
Impact : Factory
Modules : Eventlog
Authors : rods
Test #1 : Run "eventlog -spdclr"
Expect : If the system has an SPD interface, it should clear the OEM area from
every dimm.

Issue : Fix EMC bridge card (D55D:87B0) is failing PCIe on Prowl NPR with
training errors due to m_negoLinkWidth is x0
Change : 17174
System : Prowl NPR
Modules : PCIe
Authors : shuangw, marky
Test #1 : Run pcie.exe on Prowl NPR with EMC bridge card (D55D:87B0) on slot 2
Expect : Verify PCIe tests pass, and Bus 83 and 84 will show "Link Not Reported"
instead of "Link Degraded".

Issue : Avalon-R reporting same drive twice in disk -conf

System : Avalon-R
Impact : Factory
Modules : Disk
Author : rdb
Test #1 : On Avalon-R chipset config run disk -conf
Expect : Drives only show up one time in output

Issue : Support new BIOS SPD error log format.

Change : 17169
System : 14G Servers
Impact : Factory
Modules : Eventlog
Authors : rods
Test #1 : Run "eventlog -spdx"
Expect : If the dimm contains a BIOS logged error, it should be formatted.

Issue : Added EMC PCIe SSD Bridge card to Add-In PCI Cards Table
System : Servers
Impact : Factory
Modules : SystemConfig
Authors : rdb
Test #1 : On a server with Isley Card installed run systemconfig -d:misc
Expect : Card to be displayed as Add-in

Issue : Removed z400s from list of low cost drives

System : Client
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a system with z400s drive run disk -conf
Expect : valid commodity type

Issue : Added ProcHot Temperature under [System Management] section of the Config
Tab.
Change : 17033
System : All
Modules : System Management
Authors : srirami
Test #1 : sysman -conf
Expect : Prochot Temperature should be displayed.

Issue : Update 16973 to workaround Avalon5 smbios issue.

Change : 17021
System : Servers
Impact : Factory and Customer
Modules : Memory
Authors : rods
Test #1 : See Change 16973.

Issue : Add support for command line arg -HHHLDir for AddInCards.ini file
System : All
Impact : factory
Modules : disk
Authors : rdb
Test #1 : run disk -conf -HHHLDir:<directory name> on a system with a new DSS HHHL
card that is not currently supported in disk HHHL tabel
Expect : Width to be HHHL

Issue : Add support for CPU on-board configurable memory/cache devices.

Change : 16973
System : Servers
Impact : Factory and Customer
Modules : Memory
Authors : rods
Test #1 : run "memory -conf"
Expect : Verify the configuration is correct and contains the devices if they are
configured as Memory or Hybrid.

Issue : Fixes issue where negotiated rate reported by controller is greater than
max rate reported by drive
System : Servers
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : run disk -LinkRateTest
Expect : all drives pass

Issue : Add Brighton Beach and Stony Beach to Device Category and add commodity
types for both
System : Client
Impact : Factory
Modules : disk
Authors : rdb
Test #1 : On a system with Stony Beach installed run disk -conf
Expect : Commodity Type of hard_drive(nvme_m2_upa)
Test #2 : On a system with Brighton Beach installed run disk -conf
Expect : Commodity Type of hard_drive(nvme_m2_upr)

Issue : Fix 0 negotiated link rate for SATA connected to PERC and 0 max link rate
for SAS connected to PERC
System : Servers
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : run disk -LinkRateTest
Expect : all drives pass

Issue : Fix WinGUI for customer burn-in. Support -h1 and fix -e1 and other issues
Change : 16902, 16910
System : All
Impact : Customer
Modules : WinGUI
Authors : marky
Test #1 : Run "start /w wingui -e1 -h1 pcie/exe"
Expect : Verify PCIe test can be aborted
Test #2 : Run "start /w wingui -e1 -h1"
Expect : Verify first error stops the test. Verify loop count is printed in output
file wingui.txt

Issue : Add stand-alone link rate test Functional Test Block

System : All
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : run disk -f:29 -mon
Expect : All tests pass

6089.2
-----------------------------------------------------------------------------------
----------------------------------
Issue : Add support for new Intel driver name iaStorAK (15.2.0.1017)
System : SKL and KBL Client systems
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On a SKL or KBL system in RAID mode with RAID set up run disk -conf
Expect : All drives output correctly in conf output

6089.1
-----------------------------------------------------------------------------------
----------------------------------
Issue : Add support for DSS/ESI Off-The-Shelf system Lucy.
Change : 16839
System : Lucy
Modules : IPMI library
Authors : rods
Test #1 : run Memory/EventLog/ServerMgmt. You will have to seed the SEL to test
all events.
Expect : Verify events decode as expected.

Issue : Add link rate test for drives connected to LSI/PERC/PMC controllers
System : Servers
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On a server with PMC/LSI/PERC controller with drives attached run disk -
f:1 -mon
Expect : All tests pass

Issue : Implemented a new solution to use processor Tjmax temperature instead of

a hardcoded value
: for thermal warning.
Change : 16828, 16831, 16834
System : All
Modules : System Management
Authors : srirami
Test #1 : Run any CPU intense application to make system CPU get hot to TjMax
(processor specific) temp.
Expect : Thermal warning will be thrown.

Issue : Fix Config D issue and add detection at both ends of the GPU Power cables
Change : 16829
System : Trailbreaker
Modules : cables
Authors : marky
Test #1 : run ePSA or cables.exe
Expect : Verify GPU Power{n} cables show "Installed" or "Not Installed" for MB end
of the cable and
: if installed, show ", GPU Detected" or ", GPU Not Detected" for the GPGPU
end of the cable

Issue : Add negotiated link rate for SATA drives

System : All
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a system that has SATA drive that supports negotiated link rate run
disk -conf
Expect : Linkrate in conf outptut

Issue : Add 6G linkrate to SWRAID and 12G linkrate to LSI/PERC

System : All
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a SWRAID platform with 6GB SATA drives run disk -conf
Expect : Linkrate of 6G
Test #2 : On a LSI/PERC platform with 12GB SATA controller and drives run disk -
conf
Expect : Linkrate of 12G

Issue : Make a separate controller for each HHHL device in disk -conf output
System : DSS
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : Run disk -conf on server with NVME drives and HHHL cards installed.
Expect : NVME drives under one controlle and each HHHL card under separate
controllers

Issue : Add bypass in disk -ficore USB DevicePath for USB VID 2297 due to driver
lockup when getting Hub Capabilities
System : All
Impact : Factory
Modules : disk
Authors : rdb
Test #1 : On a system with kernel debugger attached run disk -ficore
Expect : Corect output with no lockup

Issue : Add DSS Mangstor MX6300 HHHL card to table

System : DSS
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : run disk -conf on system with Mangstor HHHL card installed
Expect : Width should be HHHL

Issue : Change Keyboard.exe -ix and Touchpad.exe -ix output from FAIL to N/A
System : All
Impact : Factory & Customer
Modules : Keyboard, Touchpad
Authors : rdb
Test #1 : run Keyboard -ix -xml
Expect : DeviceStatus in keyboard.xml should be "Not Applicable"
Test #1 : run start /wait Keyboard -ix -xml
Expect : returned Errorlevel should be 2
Test #3 : run Touchpad -ix -xml
Expect : DeviceStatus in touchpad.xml should be "Not Applicable"
Test #4 : run Touchpad -ix -xml
Expect : returned Errorlevel should be 2

Issue : Add NVDimm indicator to memory configuration.

Change : 16740
System : Any 14G
Impact : Factory and Customer
Modules : Memory
Authors : rods
Test #1 : Run "memory -conf" with an nvdimm installed.
Expect : The detail of nvdimm should include a line with "HybridType NVDIMM".
Issue : Implemented error message for Non-Dell battery. Error will be thrown when
there
: is a non-dell battery and BIOS does not charge it.
Change : 16695
System : All
Modules : Battery
Authors : srirami
Test #1 : Run battery test on a system with non-dell battery.
Expect : Error will be thrown saying "Not a Dell battery" if BIOS does not charge
the non-dell battery.

Issue : Added processor production/non-production check for Kaby Lake CPU.

System : any with Kaby Lake CPU
Impact : Factory
Modules : SystemConfig
Authors : carl
Test #1 : systemconfig -xml
Expect : Processor to show Production or Non-Production and not Unknown.

Issue : Add PCIID 1D6A 0001 1D6A 0001 to AddIn Card List
System : SailFish
Impact : Factory
Modules : SystemConfig
Authors : rdb
Test #1 : On a system with this PCI Card run SystemConfig -d:Misc
Expect : For this device AddInDevice will be "YES"

Issue : GU90N (DPN 9M9FK) ODD reports tray ejected even if it didn't
System : Client
Impact : Factory
Modules : disk
Authors : rdb
Test #1 : On a system with GU90N hold ODD closed and run disk -d:cdrom -mediaeject
Expect : Failure

Issue : Micron M600 SED drives reporting as IEEE1667 causing exception error
System : Prowl
Impact : Factory
Modules : disk
Authors : rdb
Test #1 : run disk -conf on system using "a" image with M600 SED SSD drives
Expaect : valid conf output

Issue : Move duplicate functions in PciLib.cpp of different environments (EFI,

IA32, WIN) to PciLibCmn.cpp
Change : 16683
System : All
Modules : BuildLibs
Authors : shuangw
Test #1 : N/A
Expect : N/A

Issue : Pounceport Add InifiniBand CX4 module

Change : 16677
System : C6320p
Modules : cables
Authors : toddb
Test #1 : Run "cables -conf"
Expect : Verify InfiniBand displays as installed or not installed
Issue : Fix WinGUI to use -f:1 for -d:HDDSD not -f:5
Change : 16670
System : Any with HDDSD devices
Impact : Customer
Modules : WinGUI
Authors : marky
Test #1 : Run "wingui disk.exe".
Expect : Does what Issue line says

Issue : Add GPU Power Cables for Horizon

Change : 16668
System : Horizon, XD
Impact : Factory and Customer
Modules : Cables
Authors : rods
Test #1 : Run "cables -conf".
Expect : Should include 3 additional lines for GPU Power cables.

Issue : [JIRA] (JIT-24431) PERC9 H730/H830/H330 HBA mode falsely starts FW

download upon DCMD
System : Servers
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : run disk -f:1 -mon
Expect : all tests pass

Issue : Add DSS Memblaze HHHL card to table

System : DSS
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : run disk -conf on DSS system with Memblaze HHHL card.
Expect : width should be HHHL

Issue : HDDFlash causes exception error

System : Kenworth
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : Put DP/NPGNR3 fwh files in release directory and run disk -hddflash -mon
Expect : drive to flash with no errors

6088.2
-----------------------------------------------------------------------------------
----------------------------------

Issue : Add PAID bit for Fingerprint Reader (bit 63)

System : any with a fingerprint reader
Impact : Factory
Modules : Cables
Authors : carl
Test #1 : run cables.exe
Expect : Fingerprint Reader to show installed if detection of the device is
supported in BIOS.

Issue : iDrac Virtual Floppy showing a RAID device

System : Pearl
Impact : Factory
Modues : Disk
Authors : rdb
Test #1 : on a Pearl run disk -ficore
Expect : iDrac Virtual Floppy should be USB

6088.1
-----------------------------------------------------------------------------------
----------------------------------

Issue : Update 14G Wave1 cables for spec updates.

Change : 16567
System : 14G Wave1 Servers
Impact : Factory and Customer
Modules : Cables
Authors : rods
Test #1 : Run "cables -conf"
Expect : Verify settings

Issue : Incorrect mbslot number for ODD in Tigris when using In-Box driver
System : Tigris
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a Tigris with ODD run disk -conf
Expect : ODD in mbslot 1

Issue : Capacity for SAS drives off by 512 bytes

System : Servers, Precision with SAS drives
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : run disk -conf
Expect : correct drie capacity

Issue : Add DSS HHHL Card in PCI ID Table (1C58 0003 1C58 0003)
System : DSS
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a system with DSS HHHL Card with PCI ID 1C58 0003 1C58 0003 run disk -
conf
Expect : Device Width will be HHHL

Issue : Add support for DDR4E, LowPowerDDR4 and nvdimm indicators to the SPD
function only. Configuration has not
: been updated yet - waiting on smbios standards.
Change : 16546
System : Servers with DDR4 and SPD interface
Impact : Factory and Customer
Modules : Eventlog
Authors : rods
Test #1 : Run "eventlog -spdx" on a Dell BIOS system.
Expect : The module should be able to format new DDR4 types. If the dimm is an
nvdimm, it should print a line.

Issue : Support ServerMgmt generating correct errorlevel on non-server systems.

Change : 16543
System : All non-Server
Impact : Factory and Customer
Modules : ServerMgmt
Authors : rods
Test #1 : Run "servermgmt" on a non-server system.
Expect : UI should say no devices were detected. Enter "echo %errorlevel%" which
should return 2.

Issue : Move 14G cables details to XML messages. Allow mixing 14G cables items
with earlier versions.
Change : 16533
System : 14G Servers
Impact : Factory and Customer
Modules : Cables
Authors : rods
Test #1 : Run "cables -details" or "cables -details -conf"
Expect : Signal details appear for each item using a column format.

Issue : Make Controller type CNTLRHDD be INTELRAID in ficore output if VendorID

is 0x8086 and DeviceId is 0x8d02 or 0x8d62
: to remove dependency on "s" WinPE image
System : 13g Servers
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a 13g server with 5 or more drives connected to on-board AHCI
controller run disk -ficore
Expect : Controllertype field to be INTELRAID for all drives connected to on-board
controller

Issue : Pounceport Remove 14G references and Password Jumper Update

Change : 16496
System : Pounceport
Modules : cables
Authors : toddb
Test #1 : run cables
Expect : Verify password jumper setting is correct

Issue : Limit number of drives tested in parallel to 25 for Verify and RandomSeek
tests
System : All
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On a system with greater than 25 drives run disk -f:2 -mon
Expect : During Verify and RandomSeek tests only 25 drives will be tested at a
time.

Issue : Add BIOS version to disk debug output

System : All
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : run disk -conf -v
Expect : "System SSID: XXXX BIOS Version: XXX" to be in debug output.

Issue : Add DSS HHHL PCI ID to HHHL Table

System : DSS
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a DSS system with DSS HHHL card run disk -conf
Expect : Width to be HHHL

Issue : Turn on some PCIe debug messages only when debug flag 0x20 is on (e.g.
run "x 20 -conf)
Change : 16458
System : All
Modules : PCI
Authors : shuangw
Test #1 : run "x 0 -conf" and "x 20 -conf"
Expect : Verify that the latter one has more PCIe debug messages

Issue : Pounceport TPM Update

Change : 16441
System : Pounceport
Modules : cables
Authors : toddb
Test #1 : run Cables
Expect : TPM status displays correctly for installed / not installed

Issue : Add DSS SAMSUNG HHHL card to HHHL table

System : DSS
Impact : Factory
Modules : disk
Author : rdb
Test #1 : Add p/n RTMFX in system and run disk -conf
Expect : Device Width will be HHHL

Issue : Hardcode BP number to 1 for SAS9311-8i

System : DSS2500
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a DSS2500 RocketFuel with SAS9311-8i installed run disk -conf
Expect : One BP with BP number 1 to be found in conf output with correct
information

Issue : Add System GUID to SIL

System : All
Impact : Factory
Modules : SystemConfig
Author : rdb
Test #1 : run systemconfig -sil
Expect : BIOS_GUID part attribute to be in Motherboard part

6087.2
-----------------------------------------------------------------------------------
----------------------------------
Issue : Add System GUID to SystemConfig Baseboard conf output
System : All
Impact : Factory
Modules : SystemConfig
Author : rdb
Test #1 : run systemconfig -d:baseboard
Expect : System GUID to be in output

Issue : SystemConfig -sil causing exception error

System : All
Impact : Factory
Modules : SystemConfig
Author : rdb
Test #1 : run systemconfig -sil
Expect : valid SIL output

Issue : Pounceport Power Supply Detection

System : Pounceport
Impact : Factory
Modules : Cables
Author : toddb
Test #1 : Run Cables
Expect : Correct power supply configuration

Issue : Add 14g Server Backplane IPMI support

System : 14g Servers
Impact : Factory
Modules : Disk
Author : rdb
Test #1 : On a 14g server run disk -conf
Expect : Valid backplane information

6087.1
-----------------------------------------------------------------------------------
----------------------------------
Issue : Add SATADOM support for EMC Quanta server
System : EMC Quanta
Impact : Factory
Modules : disk
Author : rdb
Test #1 : run disk -conf
Expect : output to appear in a timely manner

Issue : Sytems using Intel enterprise driver have same drive twice if more than 1
drive in system
System : Avalon 3, Avalon 5, Avalon 7
Impact : Factory
Modules : disk
Author : rdb
Test #1 : Boot Avalon 3/5/7 with multiple SATA drives connected to on-board SATA
controller to "s" pxe image and run
: disk -conf
Expect : The correct number of drives in conf output

Issue : Update factory correctable ECC filtering to allow 4 per-dimm.

System : Servers
Change : 16266
Impact : Factory
Modules : Eventlog, Memory, ServerMgmt, smbios/eventlog libraries
Author : rods
Test #1 : run modules as normal
Expect : No failures should be observed unless a single dimm encounters more than
4 correctable ECC errors.

Issue : Back out disk -ficore slot field 5 change and add Controller:Bay:Slot
field at end of current output
System : All
Impact : Factory
Authors : rdb
Modules : disk
Test #1 : run disk -ficore
Expect : field 5 to have <Slot> only and fields 14, 15, and 16 to have
Controller:Bay:Slot format

Issue : Add support for iaStorAV driver in Customer release

System : Client
Impact : Customer
Modules : Disk
Authors : rdb
Test #1 : On a system that has full O/S with iaStorAV driver installed and SATA HDD
connected to MB controller
: run disk -conf
Expect : Commodity to be hard_drive.
Test #2 : On same system run disk -f:5 -mon
Expect : All tests to be run on HDD and all tests pass.

Issue : Error Code 57 returned intermittenly for Customer build

System : Client
Impact : Customer
Modules : Disk
Authors : rdb
Test #1 : On a system that has full O/S with iaStorAV driver installed and SATA HDD
connected to MB controller
: run disk -conf
Expect : Valid conf output with no error messages displayed

Issue : Samsung PM961 NVMe drives failing Verify Test

System : Client
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : run disk -f:5 -mon
Expect : All tests pass

Issue : Samsung SM961 NVMe drive reporting as wrong commodity type

System : Client
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : run disk -conf
Expect : Commodity to be hard_drive(nvme_m2_hpr)

Issue : Trim spaces in SIL output values

System : All
Impact : Factory
Modules : SystemConfig
Authors : rdb
Test #1 : run systemconfig -SIL
Expect : no leading or trailing spaces in values

6086.1
-----------------------------------------------------------------------------------
----------------------------------
Issue : Cables support for Pounceport/Pioneer based off of TRD to support mDiags
Dev
System : Pounceport/Pioneer
Change : 16141
Impact : Development
Modules : cables
Authors : toddb
Test #1 : run "cables"
Expect : Check configuration and results

Issue : Add support for Intel RST driver version 15.x

System : All with Intel chipset
Impact : Customer & Factory
Modules : Disk
Author : rdb
Test #1 : run disk -conf
Expect : Valid conf output
Test #2 : run disk -f:4 -mon
Expect : All tests pass

Issue : Additional cables support for Juno/Horizon due to new information

System : Juno/Horizon
Change : 16091
Impact : Customer and Factory
Modules : cables
Authors : rods
Test #1 : run "cables"
Expect : Check configuration and results

Issue : BITS283131:BITS � Disk conf output from WBDD 6085.3 on Glenn has the
wrong slots info
System : Glen
Impact : Factory
Modules : Disk
Author : rdb
Test #1 : run disk -conf
Expect : Slot numbers to start at 0 and go through 11

Issue : BITS212214 - add a check for fan being over a specified speed
Note : Use the new test on one fan at a time. The limit on the command line
applies to all fans otherwise.
System : All
Impact : Factory
Modules : Fan
Author : carl
Test #1 : fan.exe
Expect : Runs the normal high and low fan speed test
Test #2 : fan.exe -f:1
Expect : Run the normal high and low fan speed test, but the test level is 1.
Test #3 : fan.exe -f:2 -d:fan:0 -RPMLimit:450
Command line contains the test level (f:2), the device (d:fan:0) and the
RPM limit (RPMLimit:d)
Expect : Fan over speed test to pass if current RPM is less than or equal to RPM
Limit
Expect : Fan over speed test to fail if current RPM is greater than the RPM limit

Issue : XML output adds the module number to upper 8 bits in error codes when
error code is 16-bit value
System : All
Impact : Factory
Modules : Exec
Author : carl
Test #1 : run ADDF module that has 16-bit error code value with -xml in command
line
Expect : The 16-bit error code to be displayed, not the 16-bit error code -or'ed-
with module number in
the upper 8 bits.

Issue : Added CPU Signature for Apollo Lake (APL) SOC for Production/Non-
Production(Sample) bit check
System : systems containing the Apollo Lake (APL) SOC processor
Impact : Factory
Modules : SystemConfig
Authors : carl
Test #1 : run SystemConfig
Expect : Production/Non-Production CPU status line will appear on Apollo Lake SOC
based systems.

Issue : WINEpsa not loading dddriver.sys

System : All
Impact : Factory
Modules : WINEpsa
Authors : rdb
Test #1 : run winepsa
Expect : dddriver.sys to be loaded

Issue : WMI dll not in Customer release

System : All
Impact : Customer
Modules : Disk
Authors : rdb
Test #1 : run disk -conf from Cuastomer release
Expect : valid conf output

Issue : Teradata HDDs displaying invalid PPIDs

System : DSS
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On DSS system with Teradata drives run disk -conf -xml
Expect : Valid characters in PPID

Issue : Add support for new chassis types from SMBIOS Type 3: 0x21 and 0x22
System : St Louis, Constantine, Ford
Impact : Customer and Factory
Modules : cables
Authors : billb
Test #1 : Run cables -conf
Expect : Chassis Type will be "IoT Gateway" or "Embedded PC" with added BIOS
Support

Issue : Remove dddriver.sys from CUSTOMER release. Use DDV driver instead.
System : All
Impact : Customer
Modules : Disk, Buildlibs
Authors : rdb
Test #1 : Build CUSTOMER release.
Expect : dddriver.sys not in release package
Test #2 : Build Customer relase. Run disk -conf
Expect : No error or warning messages that have to do with the driver.

6085.3
-----------------------------------------------------------------------------------
----------------------------------
Issue : BTO/FACE FE022244 ADC LAB PS3 R630XL with (4) 800GB P3700 PCI-e SSD
Controller HDD and RMSD failed - Teradata
System : Servers
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On Teradata system with 4 pciessds run disk -conf
Expect : correct drive slot numbers

Issue : Fix the Provider string in the log file when the driver loads.
: Changed it from %Dell% (with percent symbols) to Dell Inc.
: Changed the INF file date to 04/26/2016 and re-signed the INF and CAT
files.
Change : 15817
System : All
Impact : Factory
Modules : DDUsbDiag
Authors : carl
Test #1 : DDUsbDiag.exe
Expect : In setupapi.dev.log in the X:\Windows\INF directory for Windows 10, the
Provider string is Dell Inc when
DDUsbDriver is loaded and finds at least one device with UBIST.

6085.2
-----------------------------------------------------------------------------------
----------------------------------
Issue : Hardcode BP number to 1 for SAS9300-8i
System : DSS2500
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a DSS2500 RocketFuel with SAS9300-8i installed run disk -conf
Expect : One BP with BP number 1 to be found in conf output with correct
information

Issue : JIT-23290 for OneSpark slot2 will not train to x16

Change : 15753, 15790
System : OneSpark (with CFI video card NVIDIA GM107GL [Quadro K620])
Modules : PCIe
Authors : marky, shuangw
Test #1 : Run ePSA and/or PCIe.exe
Test #2 : Verify no training error for the video card, or any x16 card

6085.1
-----------------------------------------------------------------------------------
----------------------------------
Issue : Ironhide Cables update with CPLD 0.0.5
System : Ironhide
Change : 15729
Authors : toddb
Modules : cables
Test #1 : run cables and verify backplane configuration (BP1 and BP2 both point to
BP1)
Expect : Both x16 and x8 backplane now show as backplane 1

Issue : Controller:Bay:Slot support for disk -ficore slot fields

System : All
Change : 15674
Impact : Factory
Authors : rdb
Modules : disk
Test #1 : run disk -ficore
Expect : slot field to have <Controller>-<Bay>-<Slot> or <Controller>-<Slot> for
no BP systems

Issue : Support for DSS Nytro HHHL card

System : DSS
Change : 15673
Impact : Factory
Modules : disk
Authors : rdb
Test #1 : On a systenm with DSS Nytro HHHL card installed run disk -conf
Expect : Nytro card and all associated drives (including LSI WarpDrive) will have
Width as "HHHL"

Issue : Add BusDeviceFunction and Bus tags for NVMe SSDs when available
System : All
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : run disk -conf on a system with NVMe SSD in AHCI mode
Expect : BusDeviceFunction and Bus tags to be displayed

Issue : RST 15.0 driver does not display drive information

System : All
Impact : Factory
Modules : Disk
Authors : rdb
Test : run disk -conf on a system with NVMe drives in a RAID configuration.
Expect : valid drive information for all drives

Issue : Add Freedom/Metallica Cables support

Change : 15630
System : Freedom/Metallica
Modules : Cables
Authors : shuangw
Test #1 : Run cables and check configuration
Expect : Pass

6084.4
-----------------------------------------------------------------------------------
----------------------------------
Issue : Add PPID validation check for NVME FRU data
System : Servers
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : run disk -conf
Expect : No PPID for NVME drive if PPID is bad

6084.3
-----------------------------------------------------------------------------------
----------------------------------
Issue : Add 1's based boot path checking for disk -ficore
System : All
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : Set system to boot in UEFI mode, boot to WinPE USB key, run disk -ficore
Expect : USB devices to have Boot variable in field 13 and CurrentBoot or * in
field 14.

Issue : Exception error on Ironhide when searching for NVMe drives

System : Ironhide
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : run disk -conf
Expect : Valid output

Issue : Kenworth with PMC controller with two BPs showing all drives on one BP
System : Kenworth
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a Kenworth with PMC controller and multiple BPs run disk -conf
Expect : Each DriveChannelId should have the BayId equal to the BackPlaneNumber
the drive is connected to

6084.2
-----------------------------------------------------------------------------------
----------------------------------
Issue : Add new PCI ID to systemconfig Add-In card table
System : ST LOUIS, FORD, CONSTANTINE
Impact : Factory
Modules : Systemconfig
Authors : rdb
Test #1 : Add network card with PCI ID 11AB 2B38 0000 0000 to a system and run
systemconfig -d:misc
Expect : Device should show up as Addin device

Issue : Kenworth with PMC controller failing BP build verification

System : Kenworth with PMC card
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : run disk -conf
Expect : BackPlaneNumber tag and BaySlot tag to be in BP section

6084.1
-----------------------------------------------------------------------------------
----------------------------------
Issue : Initial 14G cables support. Initial support for Juno, Horizon,
HorizonXD.
Change : 15516
System : Servers
Modules : Cables
Authors : rods
Test #1 : Not ready for general release yet.

Issue : Add USB bootvar support for disk -ficore

System : All
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : Set system to boot in UEFI mode, boot to WinPE USB key, run disk -ficore
Expect : USB devices to have Boot variable in field 13 and CurrentBoot or * in
field 14.

Issue : Add AMEA to Kenworth configuration

System : Kenworth
Impact : Factory
Modules : cables
Authors : bbw
Test #1 : On a Kenworth run cables -conf
Expect : confirm AMEA and vFlash outputs match configuration

Issue : Miramar in uefi mode with NVMe drives failing disk -f:6
System : Miramar
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : Run disk -f:6 -mon on a Miramar in uefi mode with NVMe drives
Expect : All tests pass

Issue : FE021653 on Grapple MLK - add processor ID for Production Level bit check
on the CPU
System : Grapple MLK
Impact : Factory
Modules : SystemConfig
Authors : carl
Test #1 : Run systemconf.exe on the system with the MLK production level CPU
Expect : Test to pass and production level to be in the XML output.

Issue : Add Boot Variable to disk -conf and disk -ficore outputs
System : All
Impact : Factory
Modules : Disk
Authors : rbd & toddb
Test #1 : Boot to WinPE using USB Key. Run disk -conf
Expect : BootVar entry for USB device should be displayed
Test #2 : Boot to WinPE using USB Key. Run disk -ficore
Expect : BootVar for USB device should be displayed in field 13. * should be in
field 13 for non USB devices

Issue : SED check causes Verify failure with UEFI boot with RAID
System : Miramar
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a Miramar with NVMe drives and set to UEFI boot with RAID set up run
disk -f:5 -mon
Expect : All tests pass

Issue : SED check causes invalid information in disk -conf

System : Client
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a system with non-SED M.2 run disk -conf
Expect : Correct conf output

Issue : Add RAID type field to disk -ficore output

System : Servers
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : Run disk -ficore on server with S130 with HDDs in RAID
Expect : Last field in PhysicalDrive for S130 will be SWRAID
Test #2 : Run disk -ficore on system with PERC/LSI controller with HDDs in a RAID
Expect : Last field in PhysicalDrive for PERC/LSI will be HWRAID
Test #3 : Run disk -ficore on server with S130 with disks set to non-RAID
Expect : Last field in PhysicalDrive for these disks will be NONRAID
Test #4 : Run disk -ficore on server in AHCI mode
Expect : Last field in PhysicalDrive for these disks will be NONRAID

Issue : Add differentiation for CM871 and CM871a

System : Client
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : run disk -conf with CM871 device installed
Expect : commodity of hard_drive(m2_ssd_lc)
Test #2 : run disk -conf with CM871a device installed
Expect : commodity of hard_drive(m2_ssd)

Issue : Add OPAL2 Security Feature Check for NVME devices

System : Client
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a Client system with M.2 SED drive that does not have SED in Model
string run disk -conf
Expect : Device type to be displayed as SED device

Issue : Invalid characters in Wireless MAC in SIL output

System : Client
Impact : Factory
Modules : SystemConfig
Authors : rdb
Test #1 : Run systemconfig -sil -gcf:<gcffile> -macfile:<macfile> where the 1 MAC
ADDRESS in the MAC file contains invalid
: characters and another MAC ADDRESS contains valid characters
Expect : SIL output to have correct MAC Address for Wireless NIC

Issue : Add PMC Enclosure Support

System : Kenworth
Impact : Factory
Modules : disk
Authors : rdb
Test #1 : On a Kenworth with PMC controller run disk -conf
Expect : BPs to be in conf output

Issue : Add updated Ironhide Cables requirements

Change : 15062
System : Servers
Impact : Factory & Customer
Modules : Cables
Authors : toddb
Test #1 : Run cables and verify configuration
Expect : Pass

Issue : Add FRU tag switch (-addFruTags) to associate status messages to

individual FRUs
System : Servers
Impact : Factory
Modules : ServerMgmt
Authors : rdb
Test #1 : On a server run ServerMgmt -conf -xml -addFruTags
Expect : Status messages under Frus specifying board details to be under a
FRU_<Device> tag
Test #2 : On a server run ServerMgmt -conf -xml
Expect : Status messages under Frus specifying board details to be lumped together

Issue : Add display FRU PPID in Servermgmt

System : Servers
Impact : Factory
Modules : Servermgmt
Authors : rdb
Test #1 : On a server run ServerMgmt -conf
Expect : FRUs with Board Serial Number and Board Part Number should display Board
PPID

6083.1
-----------------------------------------------------------------------------------
----------------------------------

Issue : Kenworth drive channel id update to use bp count

System : Kenworth
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a Kenworth Single Node Chassis put drives in A and B sections. Run
disk -conf
Expect : BayId of DriveChannelId should be different between drives in section S
and section B

Issue : Update Storelib dlls

System : Servers, Workstation with LSI controllers
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : run disk -conf on a system with LSI controller
Expect : All Controllers and HDDs to be correct
Test #2 : run disk -f:1 on a system with LSI controller
Expect : All tests pass

Issue : Add new VID:PID values for Liteon and Suyin camera modules. These are on
the new Starlord and Drax systems, and will be on others.
System : Drax, Starlord
Impact : Factory
Modules : DDUsbDiag.exe
Authors : carl
Test #1 : run DDUsbDiag.exe
Expect : Cameras with new ID values will be found and tested.

Issue : Kenworth Single Node Chassis HDDs sharing DriveChannelIds

System : Kenworth
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a Kenworth Single Node Chassis put drives in A and B sections. Run
disk -conf
Expect : BayId of DriveChannelId should be different between drives in section S
and section B

Issue : Add Security Receive/Send commands for NVMe SED devices

System : All
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a system with NVMe SED drive run disk -conf
Expect : SED drive type in output

Issue : Add Ironhide SAS A/B Cables support

Change : 15083, 15092
System : Ironhide
Modules : Cables
Authors : marky
Test #1 : Run cables
Expect : SAS A/B cables to show installed, especially Ironhide2

6082.1
-----------------------------------------------------------------------------------
----------------------------------

Issue : Add Ironhide Cables support

Change : 15062
System : Ironhide
Modules : Cables
Authors : toddb
Test #1 : Run cables and check configuration
Expect : Pass

Issue : Add VID:PID for new camera vendor. Camera is being used on Starlord
systems.
Change : 15042
System : Skylord systems
Modules : DDUSBDiag, DDUSBDriver
Authors : carl
Test #1 : DDUSBDiag.exe
Expect : Driver to load for the new camera vendor (VID_2880) and the new cameras
(PID_2C0x range).

Issue : Some PCIe slots are not detected as "empty" because some PCI-PCI bridges
do not support sLinkCap.m_dataLinkCapable
Change : 15032
System : OneSpark
Modules : PCIe
Authors : marky
Test #1 : ePSA/PCIe.exe configuration
Expect : Verify Slot 2 in R230 shows "empty" in config when it is empty. (or Slot
1 and Slot 2 for T130)

Issue : Wrong Device ID for HHHL card

System : DSS
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a server that had DSS HHHL card installed run disk -conf
Expect : FormfactorWidth will be HHHL
Issue : Add HHHL Table and Ini file support for DSS
System : Servers
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a server that had DSS HHHL card installed run disk -conf
Expect : FormfactorWidth will be HHHL

Issue : Add support for IoT device to run disk and processor tests from sysman
System : ST_LOUIS and ST_LOUIS_INDST
Impact : Factory
Modules : Sysman, disk
Authors : rdb
Test #1 : run SysMan -processorTest -diskTemperatureTest
Expect : Disk temperature in Sysman output and CPU temperature to increase

Issue : Added serial loopback support for ST_LOUIS Industrial

System : ST_LOUIS Industrial
Impact : Factory
Modules : Serial
Authors : rdb
Test #1 : attach loopback cables and run serial -i -util:5
Expect : ALl tests pass

Issue : Add P3700 HHHL to AddInCards list

System : Servers
Impact : Factory
Modules : Systemconfig
Authors : rdb
Test #1 : On a system with P3700 installed run systemconfig -d:misc
Expect : For PCI ID 8086 0953 8086 00e4 device should be add-in and have PCI slot
number

Issue : BITS268652 [ePSA False PASS with bad AC adapter]

System : Client
Impact : Customer
Modules : Charger
Authors : Srirami
Test #1 : Charger
Expect : With bad AC adapter that had bad ID pin or with Unknown AC adapters, the
Charger test throws the Warning instead of PASS.

6081.3
-----------------------------------------------------------------------------------
----------------------------------

Reason : Fixed constant speed fan detection

Change : 14887
System : Shadowcat (Systems with Liquid Cooling Module that has a constant speed
fan and tach signal)
Modules : Fan
Authors : billb
Test #1 : Run WBDD: Fan -detectLCM:1 -Tolerance:15
Expect : Test passes when a constant speed CPU Fan is detected, fails for a normal
fan
Test #2 : Run WBDD: Fan -detectLCM:0 -Tolerance:15
Expect : Test passes for a normal fan, fails if any fan is a constant speed fan
6081.2
-----------------------------------------------------------------------------------
----------------------------------

Reason : Added constant speed fan detection

Change : 14887
System : Shadowcat (Systems with Liquid Cooling Module that has a constant speed
fan and tach signal)
Modules : Fan
Authors : billb
Test #1 : Run WBDD: Fan -detectLCM:1 -Tolerance:15
Expect : Test passes when a constant speed CPU Fan is detected, fails for a normal
fan
Test #2 : Run WBDD: Fan -detectLCM:0 -Tolerance:15
Expect : Test passes for a normal fan, fails if any fan is a constant speed fan

6081.1
-----------------------------------------------------------------------------------
----------------------------------

Issue : Bug with conversion of Battery "Remaining Capacity" and "Full Capacity"
values.
System : Client
Impact : Customer & Factory
Modules : Battery
Authors : Srirami
Test #1 : Battery
Expect : Verify first 0 after decimal point is not ignored in "Remaining Capacity"
and "Full Capacity" values (e.g. 6.07 instead of 6.7)

Issue : Extra HDD in firewheel when SCSIx was greater than SCSI16
System : Firewheel (Sandstorm)
Impact : Factory
Modules : disk
Authors : rdb
Test #1 : On a firewheel with only 1 HDD and all PCI slots filled with fibre
channel cars run disk -conf
Expect : Only 1 HDD in output

Issue : Add ESG NVMe FRU support to get PPID

System : 13g servers
Impact : Factory
Modules : Disk
Author : rdb
Test #1 : On a 13G server with NVMe drives installed run disk -conf
Expect : PPID in output for NVMe Drives

Issue : Spec change for lc and hpr Client drives fro WORD 159 to WORD 158
System : Client
Impact : Factory
Modules : disk
Author : rdb
Test #1 : On a client system with hpr/lc drives that meet new Client HDD spec run
disk -conf
Expect : Commodity type to be hard_drive(ssd_hpr)/hard_drive(ssd_lc).

Issue : DSS Non-Dell PCIe SSDs & NVME drives failing MDiags build verification
for slot equal 254
System : DSS
Impact : Factory
Modules : disk
Authors : rdb
Test #1 : On a DSS system with 2 or more non-Dell NVMe drives run disk -conf
Expect : Non-Dell NVMe drive slot numbers start at 254 and decrement.

Issue : fReadPhyMemory functions return the number of bytes read

System : All
Impact : Factory
Modules : Buildlibs
Authors : rdb
Test #1 : run systemconfig -d:misc
Expect : Pass

Issue : Add fPCIConfigDwordEx for registers > 0xFF

System : All
Impact : Factory
Modules : Buildlibs
Authors : tdb, rdb
Test #1 : run pcie
Expect : Pass

6080.2
-----------------------------------------------------------------------------------
----------------------------------

Issue : NVMe PPID displaying incorrectly

System : Client with M.2 NVMe devices
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a system with M.2 NVMe device run disk -conf
Expect : Valid PPID that is not byte swapped

6080.1
-----------------------------------------------------------------------------------
----------------------------------

Issue : Add PCI ID for Add-in Controller to Add-In card list

System : Client
Impact : Factory
Modules : Systemconfig
Authors : rdb
Test #1 : On a system with DP/N 270MH Add-In controller run systemconfig -d:misc
Expect : Card with PCI ID 1B6F 7023 1B6F 7023 to show as Add-In card

Issue : Add HHHL support for DSS

System : DSS
Impact : Factory
Modules : disk
Authors : rdb
Test #1 : On a system with P3700 run disk -conf
Expect : Controller and Device FormfactorWidth tags should be "HHHL". Controller
PCI ID should be same as Device PIC ID

Issue : M.2 SATA not showing up as mSATA in disk-ficore output

System : Bluefin
Impact : Factory
Modules : disk
Authors : rdb
Test #1 : On a Bluefin with M.2 SATA device adhering to Client A07 spec run dissk -
ficore
Expect : MSATA to be in output

Issue : BIOS returns EDX buffer as it was instead of proper event log data.
Output a specific error message for this "LED BIOS-Diags Interface Error"
System : Somerset, Blackwell
Impact : Factory
Module : EvLog
Authors : carl
Test #1 : Run EvLog and look at output.
Expect : When the Software SMI does not return the correct buffer, the error
message is displayed.

Issue : Add Disk temperatures to SysMan

System : All
Impact : Factory
Modules : SysMan
Authors : rdb
Test #1 : run sysman -diskTemperature
Expect : Disk temperatures in output

Issue : Add Disk Temperature Monitor Function

System : All
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : run disk -MonDiskTemp
Expect : HDD temperatures to be displayed in output loop until Ctrl-C or abort

Issue : Add PCI Infiniband classcode check for Mellanox cards

System : Servers
Impact : Factory
Modules : Systemconfig
Authors : rdb
Test #1 : Boot system to Win 10 PE and run systemconfig -d:NIC on a server with
Mellanox card
Expect : Card does not show up in output

6079.2
-----------------------------------------------------------------------------------
----------------------------------

Issue : Remove hard coded value for ST LOUIS ssid in serial test
System : ST_LOUIS
Impact : Factory
Module : Serial
Authors : rdb
Test #1 : run serial -i -util:5
Expect : All tests pass

Issue : Add VID:DID for new USB camera being used in Rocket BSW. Added 1BCF:2C8x
range
System : Rocket
Impact : Factory
Module : DDUSBDiag
Authors : carl
Test #1 : run ddusbdiag.exe on Rocket
Expect : Driver to load for the USB camera, USB BIST tests to operate properly.

6079.1
-----------------------------------------------------------------------------------
----------------------------------

Issue : Add External Loopback testing for ST LOUIS

System : ST LOUIS
Impact : Factory
Modules : Serial
Authors : rdb
Test #1 : Connect all Loopback cables to ST LOUIS and run serial -i
Expect : Prompts to add loopback cables and all tests pass
Test #1 : Connect all Loopback cables to ST LOUIS and run serial -i -util:5
Expect : No Prompts to add loopback cables and all tests pass

Issue : Intel 14.7 driver update

System : Client
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : Put a Blue FIn with NVMe drive in RAID mode and run disk -conf
Expect : Complete information in conf output for NVMe device

Issue : CFI ODD not being recognized as DVDRW

System : Optiplex
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : Install CFI ODD and run disk -conf
Expect : correct commodity device

6078.3
-----------------------------------------------------------------------------------
----------------------------------

Issue : Back out ESG Hybrid drive issue fx

System : All
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : Install Hybrid drive in system
Expect : Commodity type to be hybrid drive type - hard_drive(ssd_v) or
hard_drive(ssh_p)

6078.2
-----------------------------------------------------------------------------------
----------------------------------

Issue : Spec change for Low cost and high performance drives
System : All
Impact : Factory
Modules : disk
Authors : rdb
Test #1 : run disk -conf on a system with CM871, Z400s, SM951 or SM871 SSD drive
Expect : Valid Commodity and commodity2 outputs

6078.1
-----------------------------------------------------------------------------------
----------------------------------

Issue : Add SMART attribute 194 check for temperature

System : All
Impact : Factory
Modules : disk
Authors : rdb,tdb
Test #1 : On a ST LOUIS with Toshiba MSATA run disk -getDriveTemp
Expect : valid drive temperature returned

Issue : Add Mezz Card detect for Retimer and PLX card
System : Steeljaw-FC, Brawn-FC
Impact : Factory
Modules : cables
Authors : bbw
Test #1 : rune cables -conf
Expect : Confirm Mezz card 1 and Mezz card 2 reflect HW installed

Issue : Add Commodity2 tag for commodity type transition

System : Client
Impact : Factory
Modules : disk
Authors : rdb
Test #1 : Install SM951 Nvme M.2 card in a system that supports M.2 and run disk -
conf
Expect : Commodity hard_drive(nvme_m2) and Commodity2 hard_drive(nvme_m2_hpr) to
be displayed

Issue : Output original and new commodity types for Client LC and HPR SSDs during
transition
System : Client
Impact : Factory
Modules : disk
Authors : rdb
Test #1 : Install SM951 Nvme M.2 card in a system that supports M.2 and run disk -
conf
Expect : Commodty types of hard_drive(nvme_m2) and hard_drive(nvme_m2_hpr) to be
displayed

Issue : ESG drives displaying as hard_drive(ssh_v)

System : Servers
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : Install WD Ranier drive and run disk -conf
Expect : Commodity type to be hard_drive(hdd)

Issue : Check NVMe drive Model string for HHHL and set FormFactorWidth
accordingly
System : All
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : Install P3700 HHHL card in a system and run disk -conf
Expect : Form Factor Width to be HHHL

Issue : Add new commodity types for Client SSDs

System : Client
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : Add CM871, Z400s, SM951 or SM871 SSD drives to a Client system
Expect : Commodity type to be hard_drive(m2_ssd_lc), hard_drive(m2_ssd_lc),
hard_drive(m2_ssd_hpr) and hard_drive(m2_ssd_hpr) respectively.

Issue : Fix issue with 4kn SATA drives log page size
System : 13G servers
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a system with H730 and 4Kn SATA drives run disk -f:1 -mon
Expect : All test pass

Issue : Add IoT serial loopback support

System : St Louis
Impact : Factory
Modules : Serial
Authors : rdb
Test #1 : Connect loopback cables to St Louis run Serial -i -util:5
Expect : All tests pass

6077.1
-----------------------------------------------------------------------------------
----------------------------------

Issue : Add internal USB Hub and bridges to internal devices list for Park City
System : Park City
Impact : Factory
Modules : SystemConfig
Authors : rdb
Test #1 : Run systemconfig -d:misc
Expect : All devices with subvendorid of 2222 and subdeviceid of 1111 to have Add-
In equal NO

Issue : Add Dummy HDD controller to DeviceList if DeviceList is empty so

errorlevel 2 is not returned when -ficore
: is specified on commandline
System : Amazon 9
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : Unplug all cables to storage devices (ODD and HDD). Remove all USB keys.
Run disk -ficore
Expect : No devices output, no warnings and errorlevel 0

Issue : Add LTE thermal sensor as index 0x000C (12).

System : tablets with LTE wireless element soldered down
Change : 14031
Impact : Factory
Modules : System Management
Authors : carl
Test #1 : Run system management and look at configuration.
Expect : Shows "LTE Thermistor" if supported
Test #2 : Run ePSA
Expect : Shows "LTE Thermistor" in the System Health tab if supported.

Issue : Add 5 minute response time for CDROM Tray test per factory request for no
operator interaction
System : All with ODD
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : Run disk -d:cdrom -f:5 -mon -ix -rk:no on system with Slimline ODD
Expect : On-screen message prompting operator to close the tray with a timeout
value in the message. After tray is closed
: mesaage should disappear and all tests pass.
Test #2 : Run disk -d:cdrom -f:5 -mon -ix -rk:no on system with Slimline ODD
Expect : On-screen message prompting operator to close the tray with a timeout
value in the message. Wait for timeout to occur.
: A new message should appear with operator interaction steps. After tray
is closed and correct key is entered the
: Message should disappear and all tests pass.

Issue : Default port address for serial port was wrong for St. Louis
System : St. Louis
Impact : Factory
Modules : Serial
Authors : rdb
Test #1 : run serial.exe
Expect : all tests pass

Issue : mSATA SED showing up as M.2 SATA SED

System : All
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a system with mSATA SED run disk -conf
Expect : Commodity of hard_drive(mssd_sed).

Issue : BITS248450 [Trailbreaker Q4] GPU information are incorrect in Config tab
of ePSA(4239A24).
Change : 13993
System : Trailbreaker
Modules : Cables
Authors : marky
Test #1 : Run Cables test on Config D
Expect : Verify 4 "GPU{n} To Switch Board" lines show "Not Applicable" for Config
D (and all other non-PLX configs)

Issue : Add support for WYSE_POTOMAC SSID

System : WYSE_POTOMAC
Change : 13975, 13972
Impact : Factory
Modules : cables
Authors : carl
Test #1 : Run Cables.exe
Test #1a: run EPSA
Expect : Cable definitions for WYSE_POTOMAC to work, Power LED flash sequence to
work.

6076.3
-----------------------------------------------------------------------------------
----------------------------------

Issue : Wireless MAC address format change for SIL

System : All
Impact : Factory
Modules : systemconfig
Authors : rdb, tdb
Test #1 : Run systemconfig -sil -macfile:<macfile with wireless mac>
Expect : MAC address in SIL should not have ":"

6076.2
-----------------------------------------------------------------------------------
----------------------------------

Issue : Systemconfig exception error when no gcf specified on command line

System : All
Impact : Factory
Modules : systemconfig
Authors : rdb, tdb
Test #1 : Run systemconfig -sil
Expect : Pass with correct SIL output

6076.1
-----------------------------------------------------------------------------------
----------------------------------

Issue : SIL updates. Add RECEID data for partnership tag. Add wireless MAC.
System : All
Impact : Factory
Modules : Systemconfig
Authors : rdb
Test #1 : run systemconfig -sil -gcf:<GCFfile> -macfile:<macfile> where <macfile>
is file generated during FIST that
: contains wireless mac.
Expect : Partnername data to contain factory and MAC data to contain wireless mac.

Issue : BITS248102:AVLR:FAN(2,4,6) sensor & Power sensor lose when remove ODD
then first time enter ePSA w/ single
: CPU. Sensors intermittently missing due to iDrac not being finished with
the sensor scan. Only observed
: in ePSA, but code is shared with WBDD.
Change : 13933
System : 13G with IPMI
Impact : Factory and Customer
Modules : IPMI Library
Authors : rods
Test #1 : Run Fan, ServerMgmt, Eventlog modules
Expect : No difference in operation from previous builds.

Issue : NVMe RAID Support

System : Miramar 15, Miramar 17
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : Setup NVME RAID and run disk -conf
Expect : NVMe drives to show up in conf output correctly
Test #2 : Run disk -f:5 -mon
Expect : All tests pass

Issue : BITS243879 Qlogic Bavaria D adapter, P/N MW6JV

Change : 13868
System : BEACHCOMBER, MEGATRON, PROWL, SANDSTORM
Impact : Factory
Modules : PCIe
Authors : marky
Test #1 : Run PCIe.exe
Expect : Verify test passes with Qlogic MW6JV card installed in x16 slot

Issue : PCIe Negotiated speed prints 5.0GT/s instead of 8.0GT/s on some buses.
Change : 13868
System : Trailbreaker
Impact : Factory
Modules : PCIe
Authors : marky
Test #1 : Run PCIe
Expect : Verify Neg Speed can display 8.0GT/s not just 5.0 and 2.5GT/s

6075.4
-----------------------------------------------------------------------------------
----------------------------------

Issue : Kenworth flush cache failure on Sata Drives attached to PMC controller
System : Kenworth
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : Run disk -flushcache on a Kenworth with Sata drives connected to PMC
controller
Expect : Pass

Issue : FE018252 BTO/FACE � CCC FSJ 11G Server COASTER order HDD test fail - hdd\
_generic\test.py
System : Coaster
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : Run disk -f:1 on a Coaster with S300 installed
Expect : Pass

Issue : M.2 NVME Vendor field blank

System : Client
Impact : factory
Modules : Disk
Authors : rdb
Test #1 : run disk -conf
Expect : Vendor and Model fields are correct

6075.3
-----------------------------------------------------------------------------------
----------------------------------

Issue : BITS245767: BITS � Kenworth flush cache failure on Sandisk SSD attached
to PMC controller
System : Kenworth
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : Run disk -flushcache on a Kenworth with SAS drives connected to PMC
controller
Expect : Pass

Issue : Add Flush Cache support for SATA drives connected to PMC controller
System : Kenworth
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : Run disk -flushcache on a Kenworth with SATA drives connected to PMC
controller
Expect : Pass

Issue : FE017849 BTO/FACE � DAO-FSJ-A2-COASTER-BUILDLOG.PY. Check log page 0 for

page DFh support
System : Coaster
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a Coaster in S100 RAID mode with Toshiba drive run disk -conf
Expect : Conf output will not hang

Issue : Workaround for -

: BITS246329 APCC Steeljaw Fan RPM Failure in QT. Error : Warning. Chassis
FanX RPM: Fan sensor for Chassis.
: FE017147 APCC Steeljaw Fan RPM Failure in QT. Error : Warning. Chassis
FanX RPM: Fan sensor for Chassis.
Change : 13777
System : Servers in Stomp chassis
Impact : Factory and Customer
Modules : ServerMgmt
Authors : rods
Test #1 : Run "servermgmt"
Expect : As part of this workaround, if the SDR sensor scan fails, it should
contain the actual hex sensor data.
: Creating the original failure is very difficult.

6075.2
-----------------------------------------------------------------------------------
----------------------------------

Issue : Add NVMe drive Vendor name support for disk -conf output
System : All
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a system with NVMe drive run disk -conf
Expect : Vendor name in conf output

Issue : Fix BITS241142 -- can't run TouchPad.exe on tablet systems with attached
keyboard dock that contains a USB based ALPS touchpad.
System : Tablet systems with keyboard/touchpad dock
Impact : Factory
Modules : Touchpad
Authors : carl
Test #1 : Run Touchpad.exe
Expect : Touchpad test screen. Touchpad operation of the test.

6075.1
-----------------------------------------------------------------------------------
----------------------------------

Issue : FE017947: BTO/FACE � CCC Server STASH Complex order DST Short failed
System : Stash
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a Stash system with more than 50 drives run disk -f:1 -mon
Expect : All tests pass

Issue : Add pmc drive flashing support

System : Kenworth
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : run disk -hddflash -fwdir:<fw directory>
Expect : Test to pass

Issue : Commodity hard_drive(pcie_m2) not in conf when NVMe device has form
factor support.
System : All with M.2 NVMe drives
Modules : Disk
Impact : Factory
Authors : rdb
Test #1 : On a system with M.2 device that has form factor support in Identify data
and does not have " M.2 " or "_M.2_"
: in the Model string run disk -conf.
Expect : NVMe commodity to be hard_drive(pcie_m2).

Issue : Obtaining descriptors from USB 3.0 root hubs on systems is generating
0x7A error code. Fixed the buffer
size and added additional -v output to show what is actually happening.
Text strings instead of numbers.
System : All
Change : 13609, 13606
Modules : DDUSbDiag
Impact : Factory
Authors : carl
Test #1 : DDUsbDiag.exe
Expect : No 0x7A fault for USB 3.0 embedded root hubs on Intel platforms.
Expect : Devices on the USB 3.0 hub are discovered and accessible.

Issue : Add Controller Device Type to disk -ficore output

System : All
Modules : Disk
Impact : Factory
Authors : rdb
Test #1 : run disk -ficore
Expect : Last field of each output line will have Controller Device Type or
UNKNOWN

6074.2
-----------------------------------------------------------------------------------
----------------------------------

Issue : Extra drive in disk -conf for Kenworth

System : Kenworth
Modules : Disk
Impact : Factory
Authors : rdb
Test #1 : run disk -conf
Expect : Correct number of HDDs
Issue : Wrong HDD slot numbers for Kenworth
System : Kenworth
Modules : Disk
Impact : Factory
Authors : rdb
Test #1 : run disk -conf
Expect : Correct HDD slot numbers

6074
-----------------------------------------------------------------------------------
----------------------------------

Issue : Extra drive in disk -conf for Kenworth

System : Kenworth
Modules : Disk
Impact : Factory
Authors : rdb
Test #1 : run disk -conf
Expect : Correct number of HDDs

Issue : Wrong HDD slot numbers for Kenworth

System : Kenworth
Modules : Disk
Impact : Factory
Authors : rdb
Test #1 : run disk -conf
Expect : Correct HDD slot numbers

Issue : Add NVMe support for Intel driver 14.6.x.x

System : D7 platforms
Modules : Disk
Impact : Factory
Authors : rdb
Test #1 : On a D7 system in RAID mode that has Intel driver 14.6.x.x loaded and has
NVMe drives run disk -conf
Expect : NVMe drives to be in conf output
Test #2 : On a D7 system in RAID mode that has Intel driver 14.6.x.x loaded and has
NVMe drives run disk -f:5 -mon
Expect : All tests pass

Issue : Add support for multiple levels of HDD F/W updating

System : All
Modules : Disk
Impact : Factory
Authors : rdb
Test #1 : Backflash an HDD to at least 3 revisions below latest. Modify f/w files
that have minimum/maximum revisions
: set so they act act as bridging f/w files. Place files in .\fw\hdd
directory. Run disk -hddflash -mon -fwDir:.\fw\hdd
Expect : Drive should incrementally flash to the highest f/w file.

Issue : Add support for details message in memory test output

Change : 13460
System : all
Modules : memory
Authors : bbw
Test #1 : run memory -f:1 -xml on system with memeory errors
Expect : confirm <details> field is output with error message.
Issue : Add support for Kenworth, Vantage, Vulcan and Vanquish
Change : 13461
System : Kenworth, Vantage, Vulcan and Vanquish
Modules : cables
Authors : bbw
Test #1 : run cables -conf
Expect : platform specific cables output detected

Issue : Supply a PAID bit for new SkyCam used on tablets. This is a side mounted
camera.
Change : 13448
System : Jayton
Modules : cables
Authors : carl
Test #1 : WBDD: cables -conf
Test #1 : ePSA: ePSA from F12 menu
Expect : Front, Rear and SkyCam data bits to be displayed and show proper state of
the camera (installed, not-installed)

6074.1
-----------------------------------------------------------------------------------
----------------------------------

Issue : Add NVMe support for Intel driver 14.6.x.x

System : D7 platforms
Modules : Disk
Impact : Factory
Authors : rdb
Test #1 : On a D7 system in RAID mode that has Intel driver 14.6.x.x loaded and has
NVMe drives run disk -conf
Expect : NVMe drives to be in conf output
Test #2 : On a D7 system in RAID mode that has Intel driver 14.6.x.x loaded and has
NVMe drives run disk -f:5 -mon
Expect : All tests pass

Issue : Add support for multiple levels of HDD F/W updating

System : All
Modules : Disk
Impact : Factory
Authors : rdb
Test #1 : Backflash an HDD to at least 3 revisions below latest. Modify f/w files
that have minimum/maximum revisions
: set so they act act as bridging f/w files. Place files in .\fw\hdd
directory. Run disk -hddflash -mon -fwDir:.\fw\hdd
Expect : Drive should incrementally flash to the highest f/w file.

Issue : Add support for details message in memory test output

Change : 13460
System : all
Modules : memory
Authors : bbw
Test #1 : run memory -f:1 -xml on system with memeory errors
Expect : confirm <details> field is output with error message.

Issue : Add support for Kenworth, Vantage, Vulcan and Vanquish

Change : 13461
System : Kenworth, Vantage, Vulcan and Vanquish
Modules : cables
Authors : bbw
Test #1 : run cables -conf
Expect : platform specific cables output detected

Issue : Supply a PAID bit for new SkyCam used on tablets. This is a side mounted
camera.
Change : 13448
System : Jayton
Modules : cables
Authors : carl
Test #1 : WBDD: cables -conf
Test #1 : ePSA: ePSA from F12 menu
Expect : Front, Rear and SkyCam data bits to be displayed and show proper state of
the camera (installed, not-installed)

6073
-----------------------------------------------------------------------------------
----------------------------------

Issue : FE017566 Steeljaw, PCIe Lanes Test failed

Change : 13323
System : Steeljaw
Modules : PCIe
Authors : marky
Test #1 : WBDD: PCIe -o:pci.txt, PCIe
Test #1 : ePSA: ePSA -o:pci.txt, ePSA
Expect : Verify PCIe test passes with Steeljaw compute sled and Stash storage sled
in Stomp chassis

Issue : Remove support for PCIe Speed testing for ePSA and all but speed display
for WBDD
Change : 13258, 13281
System : All
Modules : PCIe
Authors : marky
Test #1 : WBDD: PCIe -o:pci.txt, PCIe
Test #1 : ePSA: ePSA -o:pci.txt, ePSA
Expect : Verify PCIe test does not fail. WBDD will display Speeds, ePSA does not.

Issue : Add Qlogic cards that won't train to X8, only x4, for Firewheel
Change : 13252
System : Firewheel
Modules : PCIe
Authors : marky
Test #1 : WBDD: PCIe -o:pci.txt, PCIe
Test #1 : ePSA: ePSA -o:pci.txt, ePSA
Expect : Verify PCIe test does not fail on Qlogic cards QLE4062C and QLE8152

Issue : Support for Micron M600 M.2 drive

System : Client
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : run disk -conf on system with Micron M600 drive
Expect : Commodity should be hard_drive(m2_ssd).

Issue : Intel iaStorA version 14.5.0.1069 NVME remapping support

System : Client systems with remapped NVME drives
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a Miranda 17 with NVME M.2 cards in RAID mode but without a RAID set
up run disk -conf
Expect : Complete device name displayed in the Model, full FWrev displayed and
valid port number
Test #2 : On a Miranda 17 with NVME M.2 cards in RAID mode but without a RAID set
up run disk -f:5 -mon
Expect : All tests (Verify, DST Short, RandomSeek) run and pass

Issue : FE017275 and FE017278 training errors on PCIe test for P/N DMDYH and
G3M8K
Change : 13185
System : CPI-only
Modules : PCIe
Authors : marky
Test #1 : run PCIe test (ePSA and WBDD)
Expect : Verify no training error for these cards

Issue : BITS226777,BITS223036 Fix OneSpark cables and Add new Trailbreaker GPGPU
sensors
Change : 13171,13258
System : OneSPark(Rachet, Bombshell, Seaspray, Shockwave), Trailbreaker
Modules : Cables
Authors : marky
Test #1 : Run ePSA and WBBD cables.exe with iDrac fw X27 or later
Expect : Verify Cables configuration works for all cables on OneSpark
: and verify GPGPU detects for GPUxToSwitchBoard work individually

Reason : BITS223521: BITS � WBDD 6070.3 (1RH65) - [Dogfish9] HDD buildverify

failed
Change : 13122
System : Dogfish9, Goodyear
Modules : Disk
Authors : billb
Test #1 : Run Disk -conf with MGNHV M.2 MSATA installed and booted to Win10 PE
(btoapp64100_01ax13.img)
Expect : Verify only HDDO and HDD1 are detected
Test #2 : Run Disk -conf with MGNHV M.2 MSATA installed and booted to Win8.1 PE
Expect : Verify only HDDO and HDD1 are detected

Issue : Incorrect display of IPMI minor version number

Change : 13064
System : All with IPMI
Module : Eventlog library
Authors : rods
Test #1 : Run "eventlog -conf"
Expect : Verify the IPMI version number. You can compare against the iDrac
display. For current systems, it is 2.0.

6072.2
-----------------------------------------------------------------------------------
----------------------------------

Issue : Add R200 VID:PID for USB Driver so that it will load the driver when the
device is found.
Change : 13031
System : Maple, Monster AIO
Module : DDUsbDiag.exe
Authors : carl
Test #1 : Run DDUsbDiag.exe
Expect : Driver to load on the R200 USB 3-D camera. UBIST tests to execute.

Issue : Add final support for OneSpark cables assumming these get fixed in
iDrac/CPLD fw: BITS226777, APB #7, BITS217402, BITS219341
Change : 13026
System : OneSPark(Rachet, Bombshell, Seaspray, Shockwave)
Modules : Cables
Authors : marky
Test #1 : Run ePSA and WBBD cables.exe
Expect : Verify Cables configuration works for all cables not affected by BITS
above and works when those BITS are fixed.

6072.1
-----------------------------------------------------------------------------------
----------------------------------

Issue : Farallon Optical device has wrong slot

System : Farallon
Module : Disk
Impact : Factory
Authors : rdb
Test #1 : On a Farallon with ODD plugged into slot 1 run disk -conf
Expect : ODD to be on MBSlot 1

Issue : SetGSB failing on Pliant 400GB SSD drives

System : All servers
Module : Disk
Impact : Factory
Authors : rdb
Test #1 : On a system with Pliant 400GB SSD drives run disk -f:1 -mon
Expect : All tests pass

Issue : Add OneSpark systems GPIO cables, tweak Trailbreaker PLX EEPROM Version
to be "Not Applicable" for non-PLX Configs
Change : 12841, 12868
System : Trailbreaker, Rachet, Bombshell, Seaspray, Shockwave
Modules : Cables
Authors : marky
Test #1 : Run ePSA and WBBD cables.exe
Expect : Verify Cables configuration on Trailbreaker PLX configs shows "PLX EEPROM
Version Not Applicable" for non-PLX confids
: and verify GPIO-based cables added for OneSpark family systems. Verify -
details works equally well with ePSA and
: cables.exe. Verify running cables a 2nd time passes in cables.exe and
does not complain "Failed to call fResult"

Issue : BITS214555 13G Equinox2 returns RESERVED when Left and Right IO riser is
installed in cables module.
Change : 12719
System : Equinox2
Modules : Cables
Authors : rods
Test #1 : Run "cables -conf".
Expect : The entries for Riser2 and Riser3 should say they are installed or absent
depending on your config.

Issue : BITS210190 : EPSA show PCIe training error on Discrete video card
Change : 12708
System : ECHO MLK (15, 17) with discrete video card wired into system as x8, but
card handles x16 normally
Modules : PCIe
Authors : carl
Test #1 : run PCIe test
Expect : No training error for the x8 condition on this card.

6071.1
-----------------------------------------------------------------------------------
----------------------------------

Issue : Add support for PCIe Speed testing

Change : 12698
System : All display speed, only Trailbreaker will fail if speed is slower than
expected
Modules : PCIe
Authors : marky
Test #1 : WBDD: PCIe -o:pci.txt, PCIe
Test #1 : ePSA: ePSA -o:pci.txt, ePSA
Expect : Verify PCIe test does not fail on Trailbreaker (or any system if compiled
for debug)
: Verify Configuration displays new speed info: "Speed Max 5.0 GT/s, Neg
2.5 GT/s" which
: may be followed by "Slow" if speed fails to reach max, "SlowHw" if
limited to slower speed
: by BIOS, or hardware strapping (or developer-forced), or "(Faster
Bridge)" if the negotiated
: speed is lower than the maximum for the bridge, but still the maximum for
the endpoint device.

Issue : BITS203446 IPMI GetDeviceFirmware 0x22 returns FF's erratically

Change : 12644
System : Trailbreaker
Modules : Cables
Authors : marky
Test #1 : Cables -conf
Expect : Verify Cables configuration on Trailbreaker PLX configs shows
PLXEEPROMVersion 00000101

Issue : Remove backplane type cables -conf output for Brawn blades/sleds
Change : 12633
System : Brawn-M, Brawn-M Plasma, Brawn-FC
Modules : Cables
Authors : bbw
Test #1 : On a Brawn system run cables -conf
Expect : Confirm that backplane type is not printed

Issue : CPLD changes to fix BITS190963 has broken cables test for Mullet
Change : 12608
System : Mullet
Modules : Cables
Authors : bbw
Test #1 : On a Mullet system with PERC, disable PERC with BIOS
Expect : PERC should show not installed

6070.3
-----------------------------------------------------------------------------------
----------------------------------

Issue : FE016202 BTO/FACE * DAO-FSJ-A2-EQUINOX2-QUALBUILD-DSTSHORT

System : Equinox2
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a Equinox2 with SAS and NVME drives run disk -f:7 -mon in a loop for 1
hour
Expect : Test pass

Issue : Add NVMe Cache Flush support for Win 10 PE

System : All
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a system with NVMe boot Win 10 PE and run disk -flushcache
Expect : Pass

Issue : NVMe PPID and FormFactor detection causing exception

System : All
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a system with NVMe drive that has PPID and Formfactor locations
populated in Identify data run disk -conf
Expect : Valid PPID and Formfactor in output

Issue : BITS185455 [Tulip][Carrizo] EPSA show PCIe training error on Discrete

video card
Change : 12513, 12517
System : Tulip AMD with discrete video card wired into system as x4, but card
handles x8 normally
Modules : PCIe
Authors : carl
Test #1 : run PCIe test
Expect : No training error for the x4 condition on this card.

6070.1
-----------------------------------------------------------------------------------
----------------------------------

Issue : Tweak cables support for OneSpark. Add Riser1 for POUNCE
Change : 12490
System : Pounce
Modules : Cables
Authors : marky
Test #1 : WBDD: Cables -conf and run Cables
Test #1 : ePSA: Inspect Cables in Configuration and run Cables test
Expect : Verify Cables configuration is correct for these platforms

Issue : Only check for 1 retired sectors entry for defect list
System : All
Module : disk
Impact : Factory
Authors : rdb
Test #1 : Run disk -f:10 on a WINTEC SSD
Expect : Valid GList count
Issue : Add Win 10 NVMe API support
System : All
Module : disk
Impact : Factory
Authors : rdb
Test #1 : On a system with NVMe booted to Win 10 PE run disk -conf
Expect : Complete information for NVMe drive in conf output

Issue : Update IPMI and SMBIOS libraries for re-entrancy

Change : 12482
System : All
Module : All
Impact : Factory & Customer
Authors : rods
Test #1 : No functional change.
Expect : All modules should behave as before.

Issue : SetGSB failing on Plasma

System : Plasma
Module : Disk
Impact : Factory
Authors : rdb
Test #1 : On a Plasma run disk -f:1 -mon
Expect : All tests pass

Issue : Update ficore output for remapped NVMe drives

System : Miramar, Dino2 and all client systems with NVMe remapping
Module : Disk
Impact : Factory
Authors : rdb
Test #1 : On a system with rempped NVMe drive run disk -ficore
Expect : PCIESSD in DriveType field (field 3)

Issue : Add switch to enable PERC debug output

System : All will PERC controller
Module : Disk
Impact : Factory
Authors : rdb
Test #1 : On system with PERC run disk -f:1 -mon -enablePERCLogging
Expect : All tests pass and storelibdebug.txt will be in the current directory

Issue : Set DEVICE register to 0x00 in Read Log Ext page 7 in DST Test for Lite-
On drive issue
System : All servers with PERC controllers
Modules : Disk
Impact : Factory
Authors : rdb
Test #1 : On a Serve with PERC controller and SATA drive run disk -f:7 -mon
Expect : Pass test

Issue : Delay first disk temperature reading for 60 seconds after start of disk
tests
System : All
Modules : Disk
Impact : Factory
Authors : rdb
Test #1 : run disk -f:1 -mon
Expect : all tests pass
Issue : Add select jedec table 7 vendor.
Change : 12375
System : Any with DDR3,DDR4. Observed on Equinox2.
Modules : Memory
Impact : Factory & Customer
Authors : rods
Test #1 : Run "memory -conf".
Expect : The dimm register manufacture should be decoded.

Issue : Add new smbios types for low power memory. Replace hex values with
#defines for SMBIOS and SPD types.
Change : 12363, 12374
System : All
Modules : Memory, Eventlog
Impact : Factory & Customer
Authors : Steve,rods
Test #1 : Run "memory -conf" on a system with a low power dimm.
Expect : The dimm type should decode correctly.

6069.3
-----------------------------------------------------------------------------------
----------------------------------

Issue : A/W Centauri not displaying correct port number for ODD in Win 10 PE
System : A/W Centauri
Modules : Disk
Impact : Factory
Authors : rdb
Test #1 : run disk -conf on A/W Centauri with ODD connected to HDD6 cable
Expect : Port number to be 2
Test #1 : run disk -conf on A/W Centauri with ODD connected to HDD5 cable
Expect : Port number to be 1

6069.2
-----------------------------------------------------------------------------------
----------------------------------

Issue : Setting BP BayId to PERC enclosure id if ipmi BP command fails

System : Stash
Modules : Disk
Impact : Factory
Authors : rdb
Test #1 : On a Stash run disk -conf
Expect : BayId to be displayed for all BPs

6069.1
-----------------------------------------------------------------------------------
----------------------------------

Issue : Add initial cables support for FIREWHEEL and POUNCE

Change : 12290
System : Firewheel, Pounce
Modules : Cables
Authors : marky
Test #1 : WBDD: Cables -conf and run Cables
Test #1 : ePSA: Inspect Cables in Configuration and run Cables test
Expect : Verify Cables configuration is correct for these platforms
Issue : Backout Updated RAIDCore APIs for MDiags build verification issue
System : Servers with Software RAID
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a system with SW RAID and gretaer than 4 HDDs run disk -conf
Expect : Two SWRAID controllers with drives attached

Issue : Grapple with Stash S130 BPs not displaying correctly

System : Stash
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a Grapple with Stash Single BP and S130 config run disk -conf
Expect : Stash BP to have ProductId of 0 x EMPTY and S130 BP with correct
information

Issue : Correct Equinox2 TPM identification

Change : 12244
System : Equinox2
Impact : Factory & Customer
Modules : Cables
Authors : rods
Test #1 : Run "cables -conf" on Equinox2.
Expect : The output from our lab system should identify the TpmType as
"TPMver1_2ROWNuvoton".

Issue : SD SCSI Confidence Test failure

System : Swordfish
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a swordfish with SD Card installed run disk -d:HDDSD -f:1 -mon
Expect : All tests pass
Test #2 : On a swordfish with SD Card installed run disk -d:HDDSD -f:2 -mon
Expect : All tests pass

Issue : Multiple vendor nvme drive support for BP slot numbering

System : DSS with Intel PCIe SSD
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a ESG system add Samsung anf Intel PCIe SSD drives
Expect : Correct BP slot numbers

Issue : SD Card Reader not showing up in disk -conf

System : Swordfish, Sukara
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a Swordfish or Sukara load Card reader driver then with SD Card
inserted in reader run disk -conf
Expect : SD Card to show up in conf output

Issue : BITS190688 print status of left riser and right riser

System : MULLET
Impact : Factory
Modules : cables
Authors : bbw
Test #1 : On a MULLET system run cables -conf
Expect : Confirm the left and right riser status is printed

Issue : Remove check for StopPatrolRead failure in SCSI Buffer Test

System : STASH
Impact : Factory
Modules : disk
Authors : rdb
Test #1 : On a system with controller in HBA mode run disk -f:2 -mon
Expect : All tests pass

Issue : Add checking all subdirectories under main firmware directory for .fwh
files for hdd flashing
System : All
Impact : Factory
Modules : Disk
Author : rdb
Test #1 : Create a main fw directory and subdirectories under it. Copy HDD firmware
into a subdirectory. Run disk -hddflash -forceflash -fwdir:<main fw directory>.
Expect : HDD to have firmare update.

Issue : Add DEFT support

System : Servers
Impact : Factory
Modules : Disk
Author : rdb
Test #1 : On a server with an HDD that supports DEFT run disk -f:23 -mon.
Expect : ALl drives to pass test.

Issue : BITS179649 [M830]Running ePSA Diags then check configuration tab will
displays twice empty value on same slot
Change : 12133
System : All
Modules : PCIe
Authors : marky
Test #1 : WBDD: PCIe -conf -o:pci.txt, PCIe
Test #1 : ePSA: ePSA -conf -o:pci.txt, ePSA
Expect : Verify configuration does not include duplicate slots on (Bullet and
Brawn) PLASMA.

6068.1
-----------------------------------------------------------------------------------
----------------------------------

Issue : Add SATA drive segmented f/w download support

System : STASH
Impact : Factory
Modules : disk
Authors : rdb
Test #1 : On a system with SATA and SAS drives and f/w available for the drives,
run disk -hddflash -fwdir:<firmware directory> -forceflash
Expect : drives flashed with no errors

Issue : Add initial cable support for Bombshell, Ratchet, Seaspray, Shockwave
Change : 12065
System : All
Modules : PCIe
Authors : marky
Test #1 : WBDD: PCIe -conf -o:pci.txt, PCIe
Test #1 : ePSA: ePSA -conf -o:pci.txt, ePSA
Expect : Verify Cables pass and configuration is correct.

Issue : Ensure diags driver is loaded if the user attemps to get SPD data.
Necessary for 12/13G. Update debug to
: show the entire packet header.
Change : 12054
System : 12G,13G
Modules : Eventlog, smbioslib
Authors : rods
Test #1 : Must be run in an environment where another diags module has not already
loaded the driver.
: Run "eventlog -spd"
Expect : Verify that the SPD interface can be accesses. There are currently no 13G
systems that have this capability.

Issue : Add "Bus XX, " to PCIe Configuration output

Change : 11954
System : All
Modules : PCIe
Authors : marky
Test #1 : WBDD: PCIe -conf -o:pci.txt
Test #1 : ePSA: ePSA -conf -o:pci.txt
Expect : Verify there is now "Bus XX, " prepended to Slot lines in PCIe.exe all
: the time, and only in ePSA Configuration tab [ PCIe ] section if compiled
for debug.

Issue : Update Storelib dll files

System : Servers
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : run disk -f:1 -mon on server with PERC controller
Expect : All tests pass

6067.2
-----------------------------------------------------------------------------------
----------------------------------

Issue : Update Stash Controller Model String for ficore

System : Stash
Impact : Factory
Authors : rdb
Test #1 : run disk -ficore
Expect : drives in stash will have "STASH" designation

6067.1
-----------------------------------------------------------------------------------
----------------------------------

Issue : Changing M.2 AHCI from mSATA to pcie_ssd per Test Strategy
System : Dino
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : run disk -ficore on a system with M.2 AHCI card that conforms to Dell
specs
Expect : device should show up as PCIESSD
Test #2 : run disk -conf on a system with M.2 AHCI card that conforms to Dell specs
Expect : mSATA should be "No"

Issue : Lite-On M.2 AHCI does not have correct commodity type
System : Dino
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : run disk -conf on a system with Lite-On M.2 AHCI card
Expect : Commodity to be hard_drive(pcie_m2)

6066.1
-----------------------------------------------------------------------------------
----------------------------------

Issue : Add -dx:<device Mnemonic> switch to disk to all for device exclusion from
testing
System : Stash
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : run disk -f:1 -mon -dx:HDD:0 on a system with multiple drives
Expect : No tests to be run on HDD:0

Issue : Add VPD B1 for non-Dell/CFI drives

System : OrcaXD
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a system with CFI SSD run disk -conf
Expect : Commodity to be hard_drive(ssd)

Issue : Enhance cables for Trailbreaker RTS 1.1 Config G (only) to add new cable
"CPU2 To Switch Board"
Change : 11799
System : Trailbreaker
Modules : Cables
Authors : marky
Test #1 : Run cables.exe
Expect : Verify cables passes Config G and "CPU2 To Switch Board" says "Installed"
only for that config.

Issue : FE014187:ADC Lab-PS3-Q1A FY16 Block-Bullit and Madone fail buildver with
DellDiag exception
System : Bullit, Madone
Impact : Factory
Module : Disk
Authors : rdb
Test #1 : On a system with Micron PCIe SSD run disk -conf
Expect : Valid conf output

Issue : Add support for Mullet (PE530XD)

Change : 11794
System : Mullet
Impact : Factory/Customer
Module : Cables
Authors : bbw
Test #1 : run cables.exe on a Mullet
Expect : output will indicate support for the system
Issue : Add Ficore support for STASH
System : Stash
Impact : Factory
Module : Disk
Authors : rdb
Test #1 : On a Stash run disk -ficore
Expect : Disks in Stash will have type of STASH

Issue : FE014016:DAO-EG3-OPTIPLEX-LANIKAI_7-_BASE:Drives Buildverify PATCHED

failed
System : Lanakai
Impact : Factory
Module : Disk
Authors : rdb
Test #1 : On a Lanakai with CFI ODD run disk -conf
Expect : ODD to be in conf output

Issue : Add SanDisk Kilimanjaro drive support

System : Servers
Impact : Factory
Module : disk
Author : rdb
Test #1 : On systrem with Kilimanjaro drive installed run disk -f:2 -mon
Expect : All tests pass

Issue : BITS176756 Observing Wrong PCIe Information after running the Diags on
the Steeljaw-M(VRTX)
Change : 11641
System : All
Modules : PCIe
Authors : marky
Test #1 : Run pcie -conf on Plasma with (2) Shared PERC's from Steeljaw or Mojo
blade
Expect : Verify Slot 9 and 10 in Configuration [ PCIe ] section are not duplicated

: with one set reporting "empty" and the other reporting the shared PERC
devices.

Issue : Add PPID and FormFactor for Client NVME drives

System : Client systems with NVME drives
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : ON a client system with NVME drive that has PPID run disk -conf
Expect : PPID and Width to show up in conf output

Issue : FE013717:Coaster fails with DD 6064.4 GetSetByte on hdd test with S300
System : Coaster w/S300
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : run disk -f:2 -mon
Expect : All tests pass

Issue : Add support for SATADOM device

System : Nutanix Appliance
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a system with SATADOM device run disk -conf
Expect : SATADOM device to be in output
Test #2 : run disk -f:2 -mon
Expect : All tests pass

Issue : Update cables TPM support for Equinox2 based on new information.
Change : 11515
System : Equinox2
Impact : Factory & Customer
Modules : Cables
Authors : rods
Test #1 : Run "cables -conf [-details]"
Expect : Should recognize the system and give some cables information.

Issue : Add Serial PCI ID to add-in card list for SystemConfig

System : TULUM
Impact : Factory
Modules : SystemConfig
Authors : rdb
Test #1 : On a TULUM with affected PCI card with PCI ID 1415 C158 1415 C158 run
systemconfig -d:misc
Expect : Card to show up as Add-In

Issue : NVMe drive size is incorrect

System : 13G Servers
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a 13G server with NVMe drive run disk -conf
Expect : Correct size of drive

Reason : Added support for Kiss (DCS server - rebranded Sideswipe -- PE R430)
Change : 11394
System : Kiss
Modules : Cables
Authors : bbw
Test #1 : Run Cables
Expect : Verify support for Kiss

Reason : Added missing Control Panel cable on Avalon357

Change : 11381
System : Avalon3, Avalon5, Avalon7
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : Verify Front Control Panel cable, no other errors, and Configuration tab
results matches hardware setup.

Reason : Added 10.1 Installed Item Status Check for BIOS cable support in BIOS
Test Interface 2.06
Change : 11374
System : Bluefin, Cod, Triggerfish, Swordfish, Whitefish, Farallon MT/SFF
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and Configuration tab results matches hardware setup.

Issue : BITS169343 - Incorrect Riser status.

Changes : 11304
System : Beachcomber and Sideswipe (R430/R530)
Impact : Factory/Customer
Modules : Cables
Authors : bbw
Test #1 : Run Cables on Beachcomber and Sideswipe
Expect : No "Riser1" or "Riser2" line should print, just "RiserXType", where X is
1 or 2

Issue : Added CPUID signature for Bay-Trail for Production/Non-Production check

Changes : 11295
System : any using the Bay-Trail CPU
Impact : Factory
Modules : Disk
Authors : carl
Test #1 : Run SystemConfig on a system with Bay-Trail CPU
Expect : Production level is shown instead of Unknown
Debug : If it shows Unknown, send output of SystemConfig -conf to Carl.

6064.1
-----------------------------------------------------------------------------------
----------------------------------

Issue : GetGSB and SetGSB need to check long version of Sense Data for certain
drives
System : Bullit
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a Bullit with Seagate ST9146853SS FW YS09 run disk -GetGSB
Expect : Test to display GetSetByte not Supported and test to pass.

6064.1
-----------------------------------------------------------------------------------
----------------------------------

Issue : Enhance cables for Trailbreaker, to describe Riser and associated cables,
better GPU Power cables
Change : 11193, 11231
System : Trailbreaker
Modules : Cables
Authors : marky
Test #1 : Run cables and cables -conf
Expect : Verify cables passes and riser and GPU power cables are more descriptive
and precise.

Issue : All LOM MACS not being displayed in SIL

Systems : Servers
Impact : Factory
Module : SystemConfig
Author : rdb
Test #1 : run SystemConfig -sil
Expect : LOM MACs in output

Issue : Add NVME Cache Flush

System : Servers with NVME drives
Impact : Factory
Module : Disk
Author : rdb
Test #1 : On a server with NVME drive(s) run disk -flushCache
Expect : All drives to have cache flushed and passing status

Issue : Add -STBI switch to disk to place drives in Standby Power mode
System : All
Impact : Factory
Module : disk
Author : rdb
Test #1 : run disk -STBI
Expect : Utility to pass

Issue : Add SetDefaultGSB to Disk Module Functional Test Blocks f:1, -f:2 and -
f:3
System : All
Impact : Factory
Module : Disk
Authors : rdb
Test #1 : Run disk -f:1 -mon, disk -f:2 -mon and disk -f:3 -mon\
Expect : SetDefGSB to be displayed in test Status screen and all tests should pass

Issue : Add inital cables support for Equinox2.

Change : 11181
System : Equinox2
Impact : Factory & Customer
Modules : Cables
Authors : rods
Test #1 : Run "cables -conf"
Expect : Should recognize the system and give some cables information. Unable to
test module at this point due
: to lack of hw.

Issue : Remove the block for the Battery and Charger testing on Silver Twins
projects. The EVT1 system will have an EC and battery and charger testing support.
Change : 11083
System : Silver Oak, Silverton
Impact : Factory
Modules : Battery
Authors : carl
Test #1 : Run battery.exe
Expect : Battery test support (with DVT1 or later hardware)

6063.3
-----------------------------------------------------------------------------------
----------------------------------

Issue : DST failing for previous failures.

System : All
Impact : Factory
Modules : disk
Authors : rdb
Test #1 : run disk -f:7 -mon on an HDD that does not have any previous DST failures
Expect : Test pass

6063.2
-----------------------------------------------------------------------------------
----------------------------------

Issue : FE012335 APCC Sandstorm failing ET1 for ControllerHDD AND RMSD
verification on SW RAID config C23
System : 13G Wave 1 and Wave 2
Impact : Factory
Modules : disk
Authors : rdb
Test #1 : Run disk -conf on S130 system with ODD
Expect : ODD to be under S130 controller in conf output

6063.1
-----------------------------------------------------------------------------------
----------------------------------

Issue : Add support for FormFactor table to determine mSATA and M.2 devices
System : All systems
Impact : Factory
Modules : disk
Authors : rdb
Test #1 : Run disk -conf on a system that has mSATA/M.2 device that supports
Formfactor table
Expect : Device to be specified as mSATA/M.2

Issue : Add Device Id 8718 for PCIe SSD bridge card

System : Steel Jaw M
Impact : Factory
Modules : disk
Authors : rdb
Test #1 : Run disk -conf
Expect : Correct PCI ID for PCIe SSD bridge card

Issue : Add 4 cables for Trailbreaker

Change : 10965, 10981
System : Trailbreaker
Modules : Cables
Authors : marky
Test #1 : Run cables and cables -conf
Expect : Verify cables passes and new cables are correct. CPU2ToSwitchBoard,
CPU1ToSlot1X16, CPU1ToSlot2X16, CPU2ToSlot2X16

Issue : Update S130 ODD detection

System : 13G servers
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a 13G server with ODD run disk -conf
Expect : Slot should be correct

Issue : Add Processor section to SIL output per SIL spec 2.07
System : All
Impact : factory
Modules : systemconfig
Author : rdb
Test #1 : run systemconfig -sil -gcf:<gcffile> -o:<silfile>
Expect : Valid Processor to be in SIL output

Issue : Add Processor section to SIL output per SIL spec 2.06
System : All
Impact : factory
Modules : systemconfig
Author : rdb
Test #1 : run systemconfig -sil -gcf:<gcffile> -o:<silfile>
Expect : Valid Processor to be in SIL output

Issue : FE012120: WBDD: [Prowl] PILOT APCC/CCC - HDD8 (SanDisk PN: F47JC) DST
failure with 6061.5
System : All systems
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : run disk -f:7 -mon
Expect : All tests pass

Issue : Add tests for NVME drives

System : 13G
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : run disk -f:6 -mon
Expect : All tests pass

Issue : Intermittent exception error caused by deleting a buffer 2x

System : Marble Falls
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : Run disk -f:6
Expect : All tests pass

Issue : Correct Intrusion cable for Trailbreaker GPUPower4

Change : 10861
System : Trailbreaker
Modules : Cables
Authors : marky
Test #1 : run cables.exe
Expect : Verify cables configuration GPUPower4 is Installed when all 4 GPU's are
connected to CPU slots.

Issue : Add NVMe API to disk

System : 13G Servers
Modules : Disk
Impact : Factory
Authors : rdb
Test #1 : On a 13G server with NVMe drives run disk -conf
Expect : Complete drive model naame and firmware version will be in conf output
Test #2 : run disk -f:7 -mon
Exepct : NVMe drives to be tested and pass.

6062.2
-----------------------------------------------------------------------------------
----------------------------------

Issue : Correct Intrusion cable for Trailbreaker and add Control Panel cable
Change : 10787, 10789
System : Trailbreaker
Modules : Cables
Authors : marky
Test #1 : run cables.exe
Expect : Verify cables configuration is correct
Test #2 : run cables test
Expect : Verify test passes

Reason : Fix inverse pattern generation in XMATSS algorithm.

Change : 10776
System : All
Modules : Memory
Authors : rods
Test #1 : Run memory
Expect : No discernable difference

Reason : Added AW Graphics Amplifier PAID bit for Caldera connected to Echo
Change : 10711
System : Echo
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and Configuration tab results matches hardware setup.
Test #2 : Cables -conf
Expect : AW Graphics Amplifier status should change when Caldera is connected

Issue : Exception error in DST

System : Spyder MLK
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : run disk -f:7 -mon
Expect : all tests pass

Issue : Add IEEE1394 PCI ID to add-in card list for SystemConfig

System : Avalons
Impact : Factory
Modules : SystemConfig
Authors : rdb
Test #1 : On an Avalon with PCI cards with PCI ID 104C 823E 0000 0000 run
systemconfig -d:misc
Expect : Card to show up as Add-In

6062.1
-----------------------------------------------------------------------------------
----------------------------------

Issue : Add support for GetSetByte command with Adaptec Controller

System : Zeus
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a Zeus with Adaptec/PMC controller and EP drive run disk -GetGSB
Expect : GetSetByte value to be displayed
Test #2 : On the same system run disk -SetGSB -GSB:<value> where <value> is 30,45
or 55
: and is not the same as the value returned in Test #1
Expect : Value is set

Issue : Add Adaptec API

System : Zeus
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a Zeus with Adaptec/PMC controller and a mix of SAS and SATA drives
run disk -conf
Expect : Controller and drives to be in conf output
Test #2 : On the same system run disk -f:2 -mon
Expect : all tests pass

Issue : FE011765: ADC LAB-PS3-13G PILOT-Megatron Buildverify: ControllerHDD AND

RMSD failed
System : Megatron
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : run disk -conf
Expect : PERC Controller package version to have valid characters

Issue : Correct cables for Trailbreaker for mdiag to start testing

Change : 10578
System : Trailbreaker
Modules : Cables
Authors : marky
Test #1 : run cables -conf
Expect : Verify configuration is correct
Test #2 : run cables
Expect : Verify test passes

Issue : BITS160102 Sometime fans aren't detected when running mdiags fan test.
System : All servers with iDrac
Change : 10569
Modules : IPMI library
Authors : rods
Test #1 : Run Fan module. This could potentially affect any sensor defined in the
IPMI SDR.
Expect : All known fans should be detected.

Issue : Add Serial Card PCI ID and IEEE1394 PCI ID to add-in card list for
SystemConfig
System : Avalons
Impact : Factory
Modules : SystemConfig
Authors : rdb
Test #1 : On an Avalon with PCI cards with PCI IDs 8086 156A 0000 0000 and 104C
823E 1028 0617 run systemconfig -d:misc
Expect : Cards to show up as Add-In

Issue : BITS160099 Sometimes IPMI command to change fan speed doesn't work.
Change : 10526
System : All with iDrac
Modules : Fan
Authors : rods
Test #1 : Run "fan". Typically, it must be looped to fail.
Expect : Verify proper operation.

6061.2
-----------------------------------------------------------------------------------
----------------------------------

Issue : Fix cables for Trailbreaker and add feature complete support
Change : 10411
System : Trailbreaker
Modules : Cables
Authors : marky
Test #1 : run cables -conf
Expect : Verify configuration is correct
Test #2 : run cables
Expect : Verify test passes

Reason : Centauri cables support

Change : 10407
System : Centauri
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and Configuration tab results matches hardware setup.

6061.1
-----------------------------------------------------------------------------------
----------------------------------

Reason : Added Centauri cables support

Change : 10392
System : Centauri
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and Configuration tab results matches hardware setup.

Issue : Replace hard_drive(m2_ssd_sed) commodity type with hard_drive(m2_sed)

System : All
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a system with M.2 SED run disk -conf
Expect : Commodity type for device to be hard_drive(m2_sed)

Issue : Add initial cables support for Trailbreaker

Change : 10362
System : Trailbreaker
Modules : Cables
Authors : marky
Test #1 : run cables -conf
Expect : Verify configuration is correct

Issue : Add support for Optional Riser: 1x16 (CPU2), Riser2, P/N 9JTXR
Change : 10347
System : Sandstorm, StandstormXD
Modules : Cables
Authors : marky
Test #1 : run cables -conf
Expect : Verify Riser 2 is "Option 1x16" not "Reserved" for 9JTXR.

Issue : Add ini file for Add-In PCI cards for SystemConfig
System : All
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : Create an INI file following instructions in AddInCards.txt. Add PCIID of
card that is known to not show up as Add-In.
: Run systemconfig -d:misc
Expect : Card to show up as Add-in
Issue : Correct delay between read when waiting for IPMI fans to stabilize.
Change : 10339
System : All IPMI
Modules : Fan
Authors : rods
Test #1 : run fan
Expect : Test takes a few seconds longer and should pass.

Reason : Added Superior Kaveri cables support

Change : 10301
System : Superior Kaveri
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and Configuration tab results matches hardware setup.

6060.4
-----------------------------------------------------------------------------------
----------------------------------

Issue : Add Serial Card PCI ID to add-in card list for SystemConfig
System : Avalons
Impact : Factory
Modules : SystemConfig
Authors : rdb
Test #1 : On an Avalon with 16550 Serial card with PCI ID 12D8 7951 12D8 7951 run
systemconfig -d:misc
Expect : Card to show up as Add-In

6060.3
-----------------------------------------------------------------------------------
----------------------------------

Issue : Add support for Bullit with 1 BP with controller and 1 BP without
controller
System : Bullit
Impact : Factory
Modules : disk
Authors : rdb
Test #1 : On Bullit with PCIe SSD BP with bridge card and drives and SAS BP with no
controller run disk -conf
Expect : PCIe SSD BP and SAS BP in conf output

Issue : Bridge Card not showing in conf when connected to universal BP and no
PCIe SSD drives installed
System : 13G servers
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a 13G server with universal BP with PCIe SSD bridge card connected to
BP and no PCIe SSD drives installed run
disk -conf
Expect : PCIe SSD Bridge Card to be in conf output

6060.2
-----------------------------------------------------------------------------------
----------------------------------
Issue : Second BP in bridged config showing up as HDD
System : Megatron
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : run disk -conf
Expect : 2 BPs and valid HDDs to show up in output

Issue : Half Height ODD passes when tray is not ejected

System : All
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : run disk -d:cdrom -f:5 -mon -rk:no -manual. Do not eject tray
Expect : test should fail
Test #1 : run disk -d:cdrom -f:5 -mon -rk:no -manual. Do not eject tray
Expect : test should fail
Test #2 : run disk -d:cdrom -f:5 -mon -rk:no -manual. Follow on-screen directions
Expect : test should pass

Issue : Tape test with media installed fails for tape generation less than drive
generation
System : Megatron
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a system with LTO5 TBU and with Gen 4 tape run disk -d:tbu -f:2 -mon
Expect : All tests pass

6060.1
-----------------------------------------------------------------------------------
----------------------------------

Issue : Add support for ST500LX012 Hybrid-V HDD

System : Goliad
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a system with ST500LX012 run disk -conf
Expect : ST500LX012 to have commodity type hard_drive(ssh_v)

Issue : Update USB INF and CAT files for new camera modules in range of 0BDA-5680
to 568F (first used on Crested Butte).
Change : 10048
System : Crested Butte
Modules : USB Driver
Authors : carl
Test #1 : Run DDUSBDiag.exe
Expect : Camera module with ID in the new range to see the driver loaded and UBIST
tests to execute.

Reason : X02 cables update for Coral

Change : 10045
System : coral
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and Configuration tab results matches hardware setup.
Issue : Support for Adaptec PMC78165 Controller
System : Radon_Z
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a Radon_Z with PMC78165 run disk -conf
Expect : Only 1 Adaptec RAID 78165 controller in output

Issue : SIL Drive iteration is not sequential

System : All
Impact : Factory
Modules : Systemconfig
Authors : rdb
Test #1 : On a system that has multiple HDDs and SSD run SystemConfig -sil -
gcf:<gcffile>
Expect : SIL Drives iteration to be sequential

Issue : Unassociated Backplane not in disk -conf

System : 13G servers
Impact : Factory
Modules : disk
Authors : rdb
Test #1 : On a system with 24 x 2.5" SAS/PCIe BP and 2 x 2.5" SAS/SATA BP and with
NVME drives installed run disk -conf
Expect : Entry for BP under PERC, under PCIe SSD and 2 x 2.5" SAS/SATA as
unassociated

Issue : NVME drives not showing up after iDrac Reset

System : 12G & 13G servers with NVME
Impact : Factory
Modules : disk
Authors : rdb
Test #1 : On a system with NVME drives run iDrac reset then run disk -conf
Expect : All NVME drives should be associated with the first PCIe SSD BP and Bay
and Slot IDs should be 254

Issue : Sandstorm S130 config returns 0 for ODD port

System : 13G with S130
Impact : Factory
Modules : disk
Author : rdb
Test #1 : On a 13G server with S130 and optical device run disk -conf
Expect : optical device to show up in conf output on correct port

Issue : Add Add-In PCIe card table for specific PCI IDs that are exceptions to
existing criteria
System : All
Impact : Factory
Modules : systemconfig
Author : rdb
Test #1 : Add Broadcom NIC with PCI ID 14E4 165A 14E4 165A to system and run
systemconfig -d:misc
Expect : Card will show up as Add-In

Issue : Add Family tag to SIL output per SIL spec 2.05
System : All
Impact : factory
Modules : systemconfig
Author : rdb
Test #1 : run systemconfig -sil -gcf:<gcffile> -o:<silfile>
Expect : Valid family to be in SIL output

Issue : FE010928 : ADC Lab-PS3-Q2FY15-Mojo fails dst short with PCIe SSD 0PHJ5
System : Mojo
Impact : Factory
Modules : disk
Author : rdb
Test #1 : On a Mojo with only nvme drives run disk -f:1 -mon
Expect : Test to pass

Issue : BITS153923 - ADC Lab-PS3-13G Qual-Sandstorm S130 config fails buildver

for CD placement w/6059.3
System : 13G with S130
Impact : Factory
Modules : disk
Author : rdb
Test #1 : On a 13G server with S130 and optical device run disk -conf
Expect : optical device to show up in conf output on correct port

Issue : PCIe SSD not showing up in correct slot on universal BP

System : 13G with universal BP and pcie ssd installed
Impact : factory
Modules : disk
Author : rdb
Test #1 : On a 13G server with 24 x 2.5" SAS/PCIe BP and with PCIe SSDs installed
run disk -conf
Expect : PCIe SSD to show up in conf output on correct slots

Issue : FE010751PSR CCC-Server-12G-ALL: systemconfig.exe cannot generate IDRAC FW

full version number.
Change : 9934
System : All with iDrac
Modules : Eventlog, ServerMgmt
Test #1 : Run "eventlog -conf"
Test #2 : Run "servermgmt -conf"
Test #3 : Run "servermgmt -firmwareID"
Expect : The iDrac version should be a 4 level version number. Some of the
displays will also include the Build.

Issue : Add support in Memory test for ePSA equivalent test levels
Change : 9927
System : All
Modules : Memory
Authors : bbw
Test #1 : Run memory test with any one of level 9, 10 or 11
Expect : successful execution of test

Issue : Bailey is a Tablet. There is no EC and will not support a battery

information interface.
: Remove the Battery test from the test tree.
Change : 9902
System : Bailey
Modules : Battery
Authors : carl
Test #1 : battery.exe
Expect : No Battery test supported.

Issue : Add SAS/PCIe BP type

System : 13G with Universal Slot BP
Impact : Factory
Modules : disk
Authors : rdb
Test #1 : run disk -conf on a 13G server with 24x2.5" BP
Expect : 24x2.5" SAS/PCIe BP in conf output

Issue : Do not fail on Dell performance sensors

Change : 9822
System : 13G Servers
Impact : Factory & Customer
Modules : Eventlog, ServerMgmt
Authors : rods
Test #1 : Run "servermgmt".
Expect : It should not fail the SEL or sensor scan for any of the "MEM Usage",
"CPU Usage" etc sensors.
Test #2 : Run "eventlog"
Expect : It should not fail the SEL scan for any of the "MEM Usage", "CPU Usage"
etc sensors.

Issue : Update iDrac version number display format

Change : 9819
System : All with iDRAC
Impact : Factory & Customer
Modules : Eventlog, ServerMgmt
Authors : rods
Test #1 : Run "servermgmt -firmwareID" on a system with iDrac
Expect : The iDrac (not BMC) versions should display as "N.NN.NN (Build N)"
Test #2 : Run "eventlog -conf" on a system with iDrac
Expect : The iDrac (not BMC) versions should display as "N.NN.NN (Build N)"

Issue : Add hybrid sed commodity types

System : All
Impact : Factory
Modules : disk
Authors : rdb
Test #1 : run disk -conf on a system with hybrid V sed and hybrid P sed drives
Expect : hard_drive(ssh_v_sed) and hard_drive(ssh_p_sed) commodity types

Issue : Add DST Short restart on "Self Test was interrupted by the host with a
hardware or software reset" error
System : All with SATA drives
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : run disk -f:7 -mon
Expect : test should pass

Issue : Add PERC Package Version to disk -conf out

System : Servers and Workstations with LSI/PERC controller
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : run disk -conf
Expect : PackageVersion to be in conf output for PERC/LSI controller

Issue : Add GetGSB switch to Disk Module to get GetSetByte value for Enterprise
Plus drives
System : All servers with PERC/SAS/LSI controller and EP drive(s) installed
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a system with Enterprise Plus HDD installed run disk -GetGSB
Expect : GSB value to be returned

Issue : Make changes to Beachcomber based on updated TRD

Change : 9723
System : Beachcomber (R530)
Modules : cables
Authors : bbw
Test #1 : Run cables
Expect : confirm signals listed per TRD

Issue : Add OEM Avalon 3, 5 and 7. Add OEM Dogfish 3, 9

Change : 9695
System : Avalon 3, Avalon 5, Avalon 7, Dogfish 3, Dogfish 9 OEM SSID support.
Modules : SAL, Cables
Impact : Factory
Authors : carl
Test #1 : cables.exe
Expect : On the OEM SSID version, cables testing will work properly.

6059.3
-----------------------------------------------------------------------------------
----------------------------------

Issue : BITS148580: WBDD 6058.4 disk conf does not have enough info to buildver
for pcie SSD on SandstormXD
System : Sandstorm
Modules : Disk
Impact : Factory
Authors : rdb
Test #1 : On a Sandstorm with 24 x 2.5" BP and with PCIe SSD drives installed run
disk -conf
Expect : PCIe SSD drives to be in conf

6059.2
-----------------------------------------------------------------------------------
----------------------------------

Reason : Added Initial Thun Lite cables support

Change : 9642
System : Thun Lite
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and Configuration tab results matches hardware setup.

Issue : MidlandX64 failing scsi_confidence with exception error

System : MidlandX64
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : Run disk -f:2 -d:hddsd -mon
Expect : test to pass

Reason : Fixed "installed" Riser Types in AvalonR Cables

Change : 9607
System : AvalonR
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and Configuration tab shows the correct Riser Types

6059.1
-----------------------------------------------------------------------------------
----------------------------------

Issue : Initial support for Sparkplug systems (Beachcomber, Soundwave, Sideswipe)

Change : 9567
System : Beachcomber, Soundwave, Sideswipe
Modules : Cables
Authors : bbw
Test : Run cables -conf on system and confirm output
Expect : Should list multiple items for each platform

Issue : Add splity backplane support

System : 13G servers
Impact : Factory
Module : Disk
Authors : rdb
Test #1 : On a 13g server run disk -conf
Expect : SplitMode tag in BP output

Issue : CFI Network En/Decyption PCI device no showing as Add-In card

System : Avalon 5
Impact : Factory
Module : SystemConfig
Authors : rdb
Test #1 : On a system with CFI Network En/Decyption PCI device (PCI ID 104A 7007
0000 0000) run systemconfig -d:misc
Expect : Device to show up as Add-in device

Isssue : fIpmiServerGen() is returning Generation 0 for Steeljaw_FC

Change : 9499
System : Servers
Impact : Factory, Customer
Module : IPMI
Authors : marky
Test #1 : run disk.exe or whatever uses this function
Expect : Verify correct 13G IPMI commands are sent

Isssue : BITS139499 : Hardware Diagnostics PCIe Bus item test fail.

Change : 9495,9498
System : Grapple
Impact : Factory, Customer
Module : PCIe
Authors : bbw
Test #1 : run WBDD pcie.exe or run ePSA PCIe test with Intel NIC
Expect : No failure detected with Intel NDC (VID/PID 8086/1523)

6058.4
-----------------------------------------------------------------------------------
----------------------------------

Issue : Missing TPM status line for Prowl, and correct TPM for Megatron and Prowl
(matching Sandstorm)
Change : 9426, 9434
System : Prowl, Megatron
Impact : Factory/Customer
Modules : Cables
Authors : marky/bbw
Test #1 : run cables -conf on Sandstorm/Avalon R/Megatron/Prowl
Expect : Two lines of TPM information should be correct

Isssue : BITS143819 : PAID signal for Power Supply on Tablets : make the PAID bit
Optional.
This prevents the fail message on tablets when the power adapter is not
plugged in.
Change : 9422
System : Bastrop, Jefferson, Midland64
Impact : Customer
Module : Cables
Authors : carl
Test #1 : run cables.exe on systems listed above.
Expect : No failure if power adapter/charger is not plugged into the system (and
the A/C source)

6058
-----------------------------------------------------------------------------------
----------------------------------

Issue : FE009741 - PCIe Issue on no hard drive systems - PCIe SSD tests not
running after iDrac Reset
System : 12G & 13G servers with PCIe SSD
Impact : Factory
Modules : disk
Authors : rdb
Test #1 : On a system with PCIe SSD drives run iDrac reset then run disk -conf
Expect : All PCIe SSD drives should be associated with the first PCIe SSD BP and
Bay and Slot IDs should be 254

Issue : BITS124644 - change request for Steeljaw/Grapple/Brawn backplane

detection HW changes, TPM fixes
Change : 9342, 9385
System : Steeljaw/Grapple/Brawn
Impact : Factory/Customer
Modules : Cables
Authors : bbw
Test #1 : run cables -conf on Steeljaw/Grapple/Brawn
Expect : backplane print should refelect correct installed backplane

Issue : Add persistent write cache enable/disable for SATA drives

System : All
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a system with SATA drive run disk -WriteCacheEnable. After test
completes power cycle. After boot to WinPE
: is complete run disk -conf.
Expect : Expect WriteCacheEnable to pass. In conf output all SAS and SATA drives
should show Write Cache Enabled
Test #2 : On a system with SATA drive run disk -WriteCacheDisable. After test
completes power cycle. After boot to WinPE
: is complete run disk -conf.
Expect : Expect WriteCacheDisable to pass. In conf output all SAS and SATA drives
should show Write Cache Disabled

Reason : Added support for Manufacturing Jumper detection

Change : 9291
System : Saffron
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and Configuration tab results matches hardware setup.
Test #2 : Run Cables -conf with the jumper is installed
Expect : ServiceModeJumper is Installed
Test #3 : Remove jumper, then after removing and replacing AC Adapter, run Cables -
conf
Expect : ServiceModeJumper is NotInstalled

Issue : FE009470 - DAO - FSL - A2 - NORTHSHORE - BASE:Drive Verification Failed

System : Northshore
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a Northshore with ODD run disk -conf
Expect : ODD to be connected to Slot 5

Issue : Cables support and fixes for QuickSync/RavageEar detection

Change : 9211
System : Servers (For Sandstorm/Prowl, remove for Megatron/Avalon R)
Modules : cables
Authors : marky
Test #1 : Run cables.exe
Expect : Verify "iDRACQuickSyncAssembly" and "iDRACQuickSyncBezel" show as Not
Installed
Test #2 : Install QuickSync cable
Expect : Verify "iDRACQuickSyncAssembly" is Installed and "iDRACQuickSyncBezel" is
Not Installed
Test #3 : Install QuickSync Bezel (when it is available)
Expect : Verify both "iDRACQuickSyncAssembly" and "iDRACQuickSyncBezel" are
Installed

Issue : Foxconn SJ GCF file not being parsed

System : All systems
Impact : Factory
Modules : SystemConfig
Authors : rdb
Test #1 : run systemconfig -sil gcf:<fsj gcf file>
Expect : Line of Business and memory Dell part numbers in SIL output

Issue : FE009744 : BTO/FACE � CCC-Server-11G-COASTER: System hang duing the IPMI

Reboot with H200 controller
System : All with H200
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : run disk -flushcache on system with H200
Expect : pass

Issue : Exception error occurring in systemconfig

System : All systems
Impact : Factory
Modules : SystemConfig
Authors : rdb
Test #1 : run systemconfig -d:hdd -conf -xml
Expect : Pass and no exception error

Issue : BITS136265 ePSA: Show Tablet Panel on tablets, not Notebook Panel in the
test tree
Change : 9146, 9147
System : all 64-bit build tablets
Modules : SAL
Authors : carl
Test #1 : Run ePSA on a tablet
Expect : Test tree to show "Tablet Panel" for the panel tests
Test #2 : Run ePSA on a notebook
Expect : Test tree to show "Notebook Panel" for the panel tests
Test #3 : Run ePSA on a AIO
Expect : Test tree to show "AIO Panel" for the panel tests

Issue : Add S130 support for 13g servers

System : 13G Servers
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : run disk -conf on system with S130
Expect : S130 controller(s) and drives to show up in output under correct
controller(s)

Issue : Add BP support for 13g servers

System : 13G Servers
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : run disk -conf
Expect : Valid BP to show up in output

Issue : Add Driver information for LSI Controllers

System : All with LSI controller(s)
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : run disk -conf
Expect : Each LSI/PERC controller will have driver information in output

Issue : Add iaStorB driver support

System : Sandstorm
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : run disk -conf
Expect : two IntelRAID controllers should be in conf output

6057
-----------------------------------------------------------------------------------
----------------------------------

Reason : Added Initial Amazon7 cables support

Change : 9027
System : Amazon7
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and Configuration tab results matches hardware setup.

Reason : BITS133321.2 - AVLR:Error msg prompts when run 'Cables' item in ePSA
4239.6
Change : 9027
System : AvalonR
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : Configuration results matches AvalonR/Sandstorm hardware setup

Issue : Increase Watchdog timeout to 24 hours for CDRead Test

System : All
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : run disk -d:cdrom -mon -f:6 and wait for 15 minutes before following
instruction in pop-up box
Expect : Test not to timeout

Issue : Add SSDs to SIL output

System : All
Impact : Factory
Modules : Systemconfig
Authors : rdb
Test #1 : run systemconfig -sil on a system with SSD drives
Expect : SSDs to be in SIL output

Reason : Update iDrac version information displays

Change : 8994, 8995
System : All with iDrac
Modules : eventlog library, IPMI library, servermgmt
Authors : rods
Test #1 : Run "eventlog -conf"
Test #2 : Run "servermgmt -conf"
Test #3 : Run "eventlog -firmwareID" on an iDrac system.
Expect : The output should contain the iDrac information using the "d.d.d (Build
d)" format.

Issue : 96 DIMMS is causing systemconfig to get an exception when outputting conf

data due to exteremely large
: amount of data to be printed in a single print statement. It also is
causing an exception to occur during
: SIL data collection.
System : Equinox
Modules : SystemConfig
Impact : Factory
Authors : rdb
Test #1 : On an Equinox with 96 DIMMS run systemconfig -conf -xml -o:out.txt
Expect : Valid configuration output with no errors
Test #2 : On an Equinox with 96 DIMMS run systemconfig -sil -o:outsil.txt
Expect : Valid sil output with no errors

Issue : 1. Add SPD interface details to Eventlog configuration.

: 2. Fix data source display when Eventlog reading SEL from a file.
Change : 8808
System : All
Modules : Eventlog, smbios lib, eventlog lib
Impact : Factory
Authors : rods
Test #1 : Run "eventlog -conf".
Expect : The output should include a line showing the SPD interface, if any.
Test #2 : Run "eventlog -selfile:xxx".
Expect : The output should display the data as IPMI source.

Issue : Fix crash in winepsa due to improper IPMI library release of smbios
library.
Change : 8919
System : All
Modules : ipmi lib
Impact : Factory
Authors : rods
Test #1 : Run "winepsa".
Expect : The program should initialize, run tests, and exit as expected.

6056
-----------------------------------------------------------------------------------
----------------------------------

Reason : PT Cables update for Avalon357

Change : 8861,8936
System : Avalon357
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and Configuration tab results match hardware setup.

Issue : SIL time UTC format incorrect (Missing "T" between date and time)
System : All
Modules : SystemConfig
Impact : Factory
Authors : rdb
Test #1 : runs systemconfig -SIL -o:sil.xml
Expect : Date element should be in UTC format <date>T<time>(gmt offset>

Reason : Added SSID and Cables Support for Saffron

Change : 8732, 8936
System : Saffron
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and Configuration tab results match hardware setup.

Issue : BITS130894 ePSA fails when Smart Card reader is not installed or
connected
Change : 8711
System : Superior
Modules : cables
Impact : Factory & Customer
Authors : vinodm
Test #1 : Run "cables"
Expect : Expect test to pass.
Disconnect Smart Card reader cable - test should pass
Disconnect Front IO cable - test should fail
Check cables -conf to show correct status based on connected cables
Reason : Updated Corse MLK cables, corrected Left & Right Speaker detect, added
Home Key detect
Change : 8704
System : Corse MLK
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and Configuration tab results match hardware setup.

Issue : Ignore "unknown" severity records when scanning the SEL. This status can
happen when the library is not
: able to determine the severity, usually due to software records.
Change : 8639
System : All IPMI
Modules : ServerMgmt
Impact : Factory & Customer
Authors : rods
Test #1 : Run "servermgmt"
Expect : The test should not fail for records with "unknown" severity.

Issue : Initial Cables release for Dogfish 3 and Dogfish 9

Change : 8616
System : Dogfish 3 and Dogfish 9
Modules : Cables
Authors : carl
Test #1 : Run ePSA
Expect : No cable test errors and Configuration tab results match hardware setup.

Issue : Initial Cables release for AW-Coral

System : Coral
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and Configuration tab results match hardware setup.

Issue : Add SD/MMC to disk -ficore output

System : All with SD/eMMC devices
Modules : Disk
Impact : Factory
Authors : rdb
Test #1 : On a system with eMMC device (Midland) run disk -ficore
Expect : Device type of SD/MMC

Issue : PCIE SSD fails flushing cache

System : All with PCIE SSD
Modules : Disk
Impact : Factory & Server
Authors : rdb
Test #1 : On a system with PCIE SSD run disk -flushcache
Expect : Pass

Issue : Speedup WinGUI when testing disk ctlrs that report "No test available for
this device" anyway
System : All
Modules : WinGUI
Impact : Customer
Authors : marky
Test #1 : wingui disk.exe
Expect : Run the HDDCONTROLLER devices and they shoud run very fast, skipping
disk.exe enumeration.

Issue : Add Mnemonic type CNTLRHDD for Intel RAID Controller device
System : All with Intel controller
Modules : disk
Impact : Factory
Authors : rdb
Test #1 : run disk -conf on system with Intel RAID controller
Expect : DeviceMnemonics of CNTLRHDD and INTELRAID

Issue : Disk reports error is device does not have tests available.
System : All
Modules : Disk
Impact : Customer & Factory
Authors : rdb
Test #1 : run disk -f:1 on controller device
Expect : Status message of "Not Applicable" and errorlevel of 2

Issue : 1. Use smbios to format dimm.

: 2. Ensure IPMI library only initializes once.
: 3. Support decode of all Wistron BMC as Dell decode.
: 4. Dump IPMI SEL event data in hex if it cannot be decoded.
: 5. Support decode of Inventec BMC.
: 6. ADDF Memory. More verification of jedec encoding in Asset string
during config.
: 7. Support 9th jedec manufacturer bank.
: 8. Fix routine that tries to detect the SPD interface.
: 9. WBDD Eventlog. Format records in SPD OEM area (-spdx). Add support
for read SPD data from a file.
: Add support for Vendor override for file SEL data. Update DDR4 size
enum for new spec.
Change : 8493
System : All IPMI
Modules : IPMI lib, Smbios lib, Memory, Eventlog
Authors : rods
Test #1 : Run "memory -conf"
Expect : Verify the Asset field is properly formatted.
Test #2 : Run "eventlog -dump"
Expect : Verify any ECC errors have the dimm identified.
Test #3 : Run "eventlog -spdx"
Expect : Verify it dumps the SPD from the dimm. Note that this is 12G MLK only for
now.

Issue : Add new class to access GPIO signals from the Broadwell LPC (Wildcat).
System : Corse MLK
Modules : Cables
Impact : Factory
Authors : carl
Test #1 : run cables -conf on Corse MLK
Expect : GPIO signals to reflect the connected/not-connected status of the
hardware.

6055.2
-----------------------------------------------------------------------------------
----------------------------------

Issue : BITS112774 ePSA 4237.4 cables test failed to detect unplugged PSU #1 & 2
and PERC DC A cable
System : Equinox
Modules : Cables
Impact : Factory & Customer
Authors : hw
Test #1 : run cables -conf on a Equinox with 24 slot SAS only backplane.
Expect : look for SAS A and SAS B cable status reflecting the real cable condition

6055.1
-----------------------------------------------------------------------------------
----------------------------------

Issue : Random Seek test locking up

System : Junction
Modules : Disk
Impact : Factory & Customer
Authors : rdb
Test #1 : run disk -f:5 -mon
Expect : All tests pass

Issue : BITS126215 Fix a Sandstorm riser type based on CPLD input

System : Sandstorm
Modules : cables
Impact : Factory & Customer
Authors : hw
Test #1 : Run cables -conf
Expect : riser 3 type should not be not present when default 2x8 is installed

Issue : BP on Plasma Shared PERC was not showing same info on secondary as on
primary controller
System : Plasma with Shared Perc
Modules : disk
Impact : Factory & Customer
Authors : rdb
Test #1 : Run disk -conf
Expect : Same devices seen on both shared PERCs
Test #2 : run disk -f:1 -mon
Expect : All tests pass
Test #3 : run disk -hddflash -fwdir:<directory with drive fw>
Expect : All drives that have downlevel firmware will be updated to latest fw

Issue : Corrected VGA_DET GPIO for VictoriaAIO - Intel

System : VictoriaAIO - Intel
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and conf results match hardware

Issue : Disk write occurring after disk cache flush

System : Coaster
Modules : disk
Impact : Factory & Customer
Authors : rdb
Test #1 : run disk -flushcache
Expect : No disk writes to occur after flush

Issue : Add module exclusion switch to SystemConfig

System : All
Modules : SystemConfig
Impact : Factory & Customer
Authors : rdb
Test #1 : Run SystemConfig -exclude:Disk.exe,Serial.exe,Battery.exe
Expect : Valid SystemConfig output with no entries for Disk, Serial or Battery
devices

Issue : Remove FDE check for legacy drives

System : All
Modules : disk
Impact : Factory & Customer
Authors : rdb
Test #1 : On a system with SED drive run disk -conf
Expect : Correct commodity type to be displayed and SED and FDE tags to be Yes

Issue : Kraken SATA drives connected to on-board SATA controller getting SAS
commands
System : Kraken
Modules : disk
Impact : Factory & Customer
Authors : rdb
Test #1 : On a Kraken with SATA drives connected to on-board SATA controller run
disk -f:8
Expect : Test pass

Issue : BITS124441 - ePSA: [Steeljaw-M] Hardware Diagnostics first item(Cables)

test fail
System : SteelJaw
Modules : cables
Authors : bbw
Test #1 : run cables
Expect : system should not fail due to heatsink error

Issue : BITS121087 Lock up during systemconfig and serial test.

System : Talon
Modules : Serial
Authors : hw
Test #1 : Boot system into WinPE run serial -conf
Expect : system should not lock up

Issue : BITS122473 - [ePSA]WLAN-BlueTooth card show not install in configuration

tab with DW1705 installed.
System : VictoriaAIO - AMD, VictoriaAIO - Intel, Travis AIO
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details with DW1705 Combo Card in the
mini-PCIE slot
Expect : no errors and conf results match hardware ("WLANBluetoothcard" status is
Installed)

Issue : FE008269: BTO/FACE � DAO FSJ - 12G SALADO_14 - Verify, System Drives
failed CDWX9
System : Salado 14, Goliad
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On a system with LITEONIT LMT-256M6M-41 mSATA 256GB SED run disk -conf
Expect : commodity to be hard_drive(mssd_sed)

Issue : Disk causing systemConfig to error with exception

System : Latitude Oak 14, Latitude Oak 15, Coaster
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : Run SystemConfig -sil -gcf:<gcffile>
Expect : Valid SIL output

Issue : Removed Intruder cables support (PT connector unpopulated)

System : ThunAIO, CaspianAIO
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and conf results match hardware

6054.3
-----------------------------------------------------------------------------------
----------------------------------

Issue : Updated Victoria AMD X02 MB (PT) cables

System : VictoriaAIO - AMD
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and conf results match hardware

6054.2
-----------------------------------------------------------------------------------
----------------------------------

Issue : Optical Device does not have correct slot number

System : Latitude Oak15 Haswell
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : run disk -conf
Expect : Optical device should have correct slot number

6054.1
-----------------------------------------------------------------------------------
----------------------------------

Issue : mSATA devices not showing up in disk conf output

System : Goodyear
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On a Goodyear with mSATA device run disk -conf
Expect : device to show up in conf output with correct model name.

Issue : Updated cables for ApriliaAIO, VictoriaAIO - AMD

System : VictoriaAIO - AMD, ApriliaAIO
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and conf results match hardware

Issue : Added additional OEM Cables support for AmazonX DBE

System : AmazonX
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and conf results match hardware

Issue : Initial cables release for InvernessAIO

System : InvernessAIO
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and conf results match hardware

Issue : BITS117921 Add Sandstorm 13G Ravage Ear quick sync detection
System : Sandstrom, Sandstrom XD, Prowl, Megatron
Impact : Factory & Customer
Modules : Cables
Authors : hw
Test #1 : Run cables -conf on 13 G systems
Expect : Check Ravage Ear status as installed in the system

Issue : BITS117949 Cable.exe -conf display incorrect TPMtype on Talon

System : Talon
Impact : Factory & Customer
Modules : Cables
Authors : hw
Test #1 : Run cables -details on Talon
Expect : Check TPM type as installed in the system

Issue : Add -ClearPriorDstFailure switch to clear DST logs

System : All
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : Run disk -ClearPriorDstFailue -mon on a system that has an HDD with a
prior DST failure
Expect : Test pass

Issue : Added PciClassInfo tag to SystemConfig output for PCI Devices

System : All
Modules : SystemConfig
Impact : Factory & Customer
Authors : rdb
Test # : Run SystemConfig -d:MISC
Expect : PciClassInfo tag to be displayed

Issue : Added initial support for Corse MLK

System : Corse MLK
Modules : Cables
Authors : mikel
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and conf results match hardware

Issue : Removed M.2 WLAN Card Detect

System : Rhine, Thun
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and conf results match hardware (Removed WLAN Card detect)

Issue : Add Client command line switch for client ODD testing
System : All
Impact : Factory
Modules : disk
Authors : rdb
Test #1 : On a system with slim line ODD run disk -d:cdrom -f:5 -Client
Expect : ODD tray to eject and all tests pass

Issue : Add FlushCache command line option to disk

System : All
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : Run disk -FlushCache -mon
Expect : All drives to pass

Issue : Add SSID for Avalon_3/_5/_7 to not display Audio Tone checkbox option
System : AValon_3/_5/_7
Impact : Customer
Modules : cables
Authors : Robib
Test #1 : Run EPSA On Avalon_3/_5/_7
Expect : Verify Audio tone button does not display in UI

Issue : Add SSID for Avalon_3/_5/_7 in (Power Button) LED Beep codes
System : AValon_3/_5/_7
Impact : Customer & Factory
Modules : cables
Authors : Robib
Test #1 : On Avalon_3/_5/_7 create a cable error that generates a beep code
Expect : Verify correct Power Button LED blinks

6053.4
-----------------------------------------------------------------------------------
----------------------------------

Issue : Intermittent failure for SATA drive showing as SAS

System : Sunrise
Impact : Factory
Modules : disk
Authors : rdb
Test #1 : run disk -conf
Expect : No message saying Test Unit Ready failure in conf output

6053.3
-----------------------------------------------------------------------------------
----------------------------------

Issue : New PCIe SSD Bridge Card did not display correct PCIID
System : Equinox
Impact : Customer & Factory
Modules : disk
Authors : rdb
Test #1 : On Equinox with PCIe SSD bridge cards run disk -conf
Expect : Correct PCI ID of Bridge Card should be in conf output

Issue : CD tray test time improvement

System : All
Impact : Customer & Factory
Modules : disk
Authors : rdb
Test #1 : On a system optical drive run disk -d:cdrom -f:5
Expect : All tests pass

6053.2
-----------------------------------------------------------------------------------
----------------------------------

Issue : Add MouseMove message to TouchScreen -w64 test to emulate swipe

System : All TouchScreen
Impact : Customer & Factory
Modules : TouchScreen
Authors : Robib
Test #1 : Run TouchScreen -w64
Expect : You can use finger to scroll through windows displayed and test contact

Issue : PCIe SSD does not show up correctly in Madone

System : Madone
Impact : Customer & Factory
Modules : disk
Authors : rdb
Test #1 : On a system with PCIe SSD run disk -conf
Expect : PCIe SSD information to be displayed correctly

6053.1
-----------------------------------------------------------------------------------
----------------------------------

Issue : CR request from CDC - implement 64-cell matrix test in Touchscreen (piano
test)
System : All Touchscreen
Modules : TouchScreen
Authors : Robib
Test #1 : Run TouchScreen -w64
Expect : New - should display 64-windows on TouchScreen window for test
Test #2 : Run TouchScreen -w4
Expect : Should display 4-corner test on TouchScreen window for test
Test #3 : Run TouchScreen -w9
Expect : Should display 9-window test on TouchScreen window for test
Test #4 : Run TouchScreen -w3
Expect : Should display 5-window test on TouchScreen window for test

Issue : BITS113929 It shows two "Digital MIC" under Cables of Configuration in

ePSA
System : Aprilia
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and conf results match hardware (Changed WebcamDigitalMIC to
Camera)

Issue : BITS112774 Add SAS A and SAS B cable signals to Equinox

System : Equinox
Impact : Factory & Customer
Modules : Cables
Authors : Robib
Test #1 : Run "cables.exe -conf"
Expect : SAS cables reported status should reflect real hardware condition

Issue : BITS112997 [R220] Cables error when running ePSA quick test.
System : Talon
Impact : Factory & Customer
Modules : Cables
Authors : hw
Test #1 : Run "cables.exe -conf"
Expect : check cables reported status should reflect real hardware condition

Issue : Add the BMC ProductID to the configuration.

System : IPMI servers.
Impact : Factory & Customer
Modules : Eventlog
Authors : rods
Test #1 : Run "eventlog -conf"
Expect : The config should include the interface specific information.

Issue : Add ESG NVMe drive support

System : Equinox
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On a system with NVMe drives installed in PCIe SSD BP run disk -conf
Expect : NVMe drives should show up under PCI Bridge Card

Issue : 1. Update Eventlog configuration to contain interface specific data.

Smbios will include the version.
: IPMI will include the BMC info, and iDrac/CPLD versions if they apply.
: 2. Update the server LCD detection code to use an OEM iDrac command
instead of the form factor.
: 3. Fix a bug that could miss retrieving iDrac revisions on older systems.
System : All. Most current servers are IPMI, many client systems support a DMI
event log.
Modules : Eventlog, ServerMgmt, SysMan
Authors : rods
Test #1 : Run "eventlog -conf"
Expect : The config should include the interface specific information.
Test #2 : Run "servermgmt"
Expect : The LCD should be tested if it exists, or reported as N/A if it does not.

Issue : Make Webcam cable optional only on TigrisAIO

System : TigrisAIO
Modules : Cables
Authors : billb
Test #1 : Disconnect TigrisAIO Webcam cable: Run Cables, Cables -conf, Cables -
details
Expect : no errors and conf results match hardware
Test #2 : Disconnect CaspianAIO Webcam cable: Run Cables, Cables -conf, Cables -
details
Expect : Cable Test will fail for Webcam cable

Issue : Initial cables release for Superior AMD

System : Superior-AMD
Modules : Cables
Authors : vinodm
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and conf results match hardware

Issue : Equinox with Combp BP does not show PCIe SSD drives under correct bridge
cards
System : Equinox
Impact : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : On a system with combo BP and at least 1 PCIe SSD in each PCIe bay run
disk -conf
Expect : Drives and BPs should show up under correct bridge cards

Issue : Initial cables release for Centauri and VictoriaAIO-Intel (update for
VictoriaAIO-AMD)
System : Centauri, VictoriaAIO-Intel, VictoriaAIO-AMD
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and conf results match hardware

Issue : Add -w3 option for Touchscreen for greater screen coverage
System : All Touch
Impact : Factory & Customer
Modules : TouchScreen
Authors : Robib
Test #1 : run Touchscreen -w3
Test #2 : run Touchscreen -w4
Test #3 : run Touchscreen -w9
Expect : Sparse matrix with -w3, 4-corner test with -w4 and 3x3 with -w9

Issue : Add TIGRIS_AIO and CASPIAN_AIO to MotherBoardMapping table

System : TIGRIS_AIO, CASPIAN_AIO
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : run disk -conf
Expect : MotherBoardSlot for Optical Device should be 1

Issue : Stack corruption issue in FSJ with HDDFlash on Plasma

System : Plasma
Impact : Factory
Modules : disk
Authors : Robib
Test #1 : Run disk -ForceFlash -HDDFlash -fwDir<Path to firmware file> on Seagate
and WD drives
Expect : Should not get Exception error and FW should be flashed successfully

Issue : Cause SATA port 1 and port 2 to be swapped

System : Aqua (FM120)
Impact : Factory
Modules : disk
Authors : bbw
Test #1 : On a dual drive Aqua in ATA mode run disk -conf
Expect : Should report two drives, one on port 0, one on port 1

Issue : Cannot read Dell Error Handler log in WBDD to find ECC memory error
messages
System : Systems with DEH UEFI protocol and ECC memory
Impact : Factory
Modules : memory and eventlog
Authors : bbw
Test #1 : On a client system with ECC memory run eventlog or memory
Expect : If an ECC memory error exists in the log, the error log entry should
print
Issue : Pcie SSD not showing up in Bells 5 and Bells 7 conf output
System : Bells 5, Bells 7
Impact : Factory & Customer
Modules : disk
Authors : rdb
Test #1 : On a Bells 5 or Bells 7 with PCIeSSD card run disk -conf
Expect : PCIESSD device to be in conf output

Issue : Update FRU parsing to protect against bad FRU data. Update IPMI debug to
remove some unneccessary info.
System : Stomp variant
Impact : Customer & Factory
Modules : ServerMgmt
Authors : rods
Test #1 : Run "servermgmt -frudump"
Expect : Should successfully dump the FRU data, even if it contains errors.

Issue : Added new camera ID's for the INF and CAT file for USB driver
System : all
Impact : Factory
Modules : DDUSBDiag
Authors : carl
Test #1 : DDUSBDiag.exe
Expect : First few lines should indicate driver was loaded if a UBIST capable
device was found.

6052.6
-----------------------------------------------------------------------------------
----------------------------------

Issue : Added new camera ID's for the INF and CAT file for USB driver
System : all
Impact : Factory
Modules : DDUSBDiag
Authors : carl
Test #1 : DDUSBDiag.exe
Expect : First few lines should indicate driver was loaded if a UBIST capable
device was found.

6052.5
-----------------------------------------------------------------------------------
----------------------------------

Issue : Stack corruption issue in FSJ with HDDFlash on Plasma

Changeset: 7357
System : Plasma
Impact : Factory
Modules : disk
Authors : Robib
Test #1 : Run disk -ForceFlash -HDDFlash -fwDir<Path to firmware file> on Seagate
and WD drives
Expect : Should not get Exception error and FW should be flashed successfully

6052.4
-----------------------------------------------------------------------------------
----------------------------------

Issue : Added Avalon Desktop SSID's to Fan module

System : Avalon 7, Avalon 5, Avalon 3
Impact : Customer & Factory
Modules : Fan
Authors : robib
Test #1 : On a Avalon run fan -conf

6052.1 to 6052.3
-----------------------------------------------------------------------------------
----------------------------------

Issue : Added Junction to M2 table and removed from mSATA table

System : Junction
Impact : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : On a Junction run disk -conf
Expect : Commodity should be hard_drive(ms_ssd)

Issue : Made General and Great Bear miniPCIe card OPTIONAL

System : General, Great Bear
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and conf results match hardware

Issue : Output drive information in SIL if PPID is not available or invalid

System : All
Impact : Factory & Customer
Modules : SystemConfig
Authors : rdb
Test #1 : On a system that has HDD with invalid or empty PPID run SystemConfig -SIL
-gcf:<gcffile>
Expect : HDD info displayed in SIL output

Issue : Add M.2 table and M.2 support in Portmapping.ini

System : All
Impact : Factory & Customer
Modules : disk
Authors : rdb
Test #1 : On a system with M.2 device run disk -conf
Expect : Commodity should be hard_drive(m2_ssd)
Test #1 : On a system that does not have an M2 table entry add the ssid and port#
to PortMapping.ini and run disk -conf
Expect : Commodity should be hard_drive(m2_ssd)

Issue : Prompt for Lid Test - keys in Msg Box should be distanced out - Brazil
request
System : All Notebooks
Modules : NBPanel
Authors : robib
Test #1 : Run NBPanel
Expect : Msg Box prompt keys should be separated by row or column

Issue : Updated cables for TigrisAIO, CaspianAIO, and Initial Release for
ApriliaAIO
System : TigrisAIO, CaspianAIO, and ApriliaAIO
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and conf results match hardware
Issue : BITS108068 Remove the "-r" switch test in Touchpad.exe as it generates
more e-mails and questions
System : All Notebooks with USB TouchScreen Functionality that uses MTConfig.sys
driver
Impact : Factory & Customer
Modules : WBDD Touchscreen
Authors : robib
Test #1 : On a system with Touchscreen enabled run command Touchscreen.exe
Expect : Touchscreen GUI should always display

Issue : Add hard_drive(m2_pciessd) commodity type

System : All
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On a system with M.2 pciessd device run disk -conf
Expect : Commodity should be hard_drive(m2_pciessd)

Issue : Add support for Bullit in a Plasma (PE VRTX) chassis

System : Bullit (M820)
Impact : Factory
Modules : all
Authors : bbw
Test #1 : "cables -conf"
Expect : Output of valid data indicates system ID is known for Bullit in Plasma
chassis

Issue : Add showing "ConfiguredSpeed" as part of memory configuration for factory

builds.
: Bios indicates DDR4 will follow the same Dell encoding in the smbios
Manufacturer/Asset fields as DDR3.
System : Any with smbios 2.7 (many 12G servers with 2.6 also have the field)
Impact : Factory
Modules : memory
Authors : rods
Test #1 : "memory -conf" or "memory -conf -xml"
Expect : If the system has the field in smbios, a new line using tag
"ConfiguredSpeed" will appear just after
: the "Speed" field.

Issue : Update PPID verify to verify all fields have valid alphanumeric
characters
System : All
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On a system with Valid HDD PPID run disk -conf
Expect : PPID to be in conf output
Test #2 : On a system with invalid HDD PPID run disk -conf
Expect : No PPID oin conf output

6051.7
-----------------------------------------------------------------------------------
----------------------------------

Issue : Add mSATA support for Junction

System : Junction
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On a Junction with mSATA installed run disk -conf
Expect : mSATA device to be specified.

6051.6
-----------------------------------------------------------------------------------
----------------------------------

Issue : PCIeSSD showing failure for -disableDIPM and -enableDIPM

System : All
Modules : Disk
Impact : Factory & Customer
Authors : rdb
Test #1 : On a system with PCIeSSD run disk -disableDIPM and disk -enableDIPM
Expect : both commands show show pass

Issue : Add PPID format checking

System : All
Modules : Disk
Impact : Factory & Customer
Authors : rdb
Test #1 : On a system that has an HDD with invalid PPID run disk -conf
Expect : No PPID in conf output

Issue : Added Front Panel USB cable detect for General SFF
System : General SFF
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and conf results match hardware

6051.5
-----------------------------------------------------------------------------------
----------------------------------

Issue : BITS074714: Remove test until they get sensor working on PT+ Boards (SEL
entry sufficient for Heatsink error )
: BITS105171 WBDD: [Equinox] 6049.6 Cables.exe is not reporting PCH
Heatsink sensor
: adding test back - sensor fixed in Board re-spin
System : Equinox
Impact : Factory
Modules : cables
Authors : robib
Test #1 : cables -conf ; cables -details
Expect : PCH Heatsink sensor status should be displayed

6051.4
-----------------------------------------------------------------------------------
----------------------------------

Issue : Sign 32 Bit driver

System : Midland
Impact : Factory
Modules : All
Authors : rdb, BryanT
Test #1 : Load driver in Secure Boot mode
Expect : Driver to load

6051.3
-----------------------------------------------------------------------------------
----------------------------------

Issue : No Hard drive systems causing disk -ficore to return error level not
equal to 0
System : Aqua
Impact :Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On an Aqua with no HDD run disk -ficore
Expect : Errorlevel 0 returned
Test #2 : On an Aqua with no HDD run disk -conf
Expect : Controller information to be displayed

6051.2
-----------------------------------------------------------------------------------
----------------------------------

Issue : PDB_R and PDB_L should be IPMI access for IDRAC MMIO
System : Equinox
Impact : Customer & Factory
Modules : Cables
Authors : robib
Test #1 : Run cables -conf
Expect : Verify PDBRight and PDBLeft wiring as installed/uninstalled

Issue : Sandstorm failing SystemConfig with exception error

System : Sandstorm
Impact : Customer & Factory
Modules : SystemConfig
Authors : rdb
Test #1 : On a Sandstorm with no PPID programmed run SystemConfig -d:Baseboard
Expect : Baseboard conf output

Issue : Slingshot fails "ServerMgmt" because it attempts to run the LCD test that
should not apply. Also changed
: the text in the message to not say "Dell PE Blade" since we could have
OEM versions.
System : Slingshot
Impact : Customer & Factory
Modules : ServerMgmt
Authors : rods
Test #1 : Run "servermgmt".
Expect : It should pass the SEL and Sensor checks then report the LCD portion as
n/a.

6051.1
-----------------------------------------------------------------------------------
----------------------------------

Issue : Add PDB_R and PDB_L cable signals detection for Equinox
System : Equinox
Impact : Customer & factory
Modules : cables
Authors : robib
Test #1 : on the supported system run cables -conf
Expect : verify all the status correctly reflects the hardware condition.

Issue : Add support for a Diags specific IPMI SEL record (basis for future
features). Ensure decode of Windows
: events includes manufacturer IANA check.
Change : 6900
System : Any IPMI
Impact : Customer & factory
Modules : ipmi library
Authors : rods
Test #1 : Run diags as normal.
Expect : No change from current operation.

Issue : BITS103129 Add Sandstorm Prowl Megatron preliminary cables detection

System : Sandstorm Prowl Megatron Talon
Impact : Customer & factory
Modules : cables
Authors : hw
Test #1 : on the supported system run cables -conf
Expect : verify all the status correctly reflects the hardware condition.

Issue : Add ability to enable/disable individual logs included in the log scan.
The enable is kept in the key, so
: the UI or sysman can scan all logs while memory can scan only a few.
Future support - no yet used.
System : Any with event log
Impact : Customer & factory
Modules : eventlog library
Authors : rods
Test #1 : Run tests as normal
Expect : No change to current operation.

Issue : Disk -ficore returns errorlevel 2 if no HDD available

System : All
Impact : Customer & factory
Modules : Disk
Authors : rdb
Test #1 : On a no HDD system run disk -ficore
Expect : Errorlevel should be 0

Issue : M.2 drives not showing up as mSATA or commodity type hard_drive(m2_ssd)

System : Junction
Modules : Disk
Impact : Factory & Customer
Authors : rdb
Test #1 : In a Junction with M.2 ssd run disk -conf
Expect : Commodity to be hardf_drive(m2_ssd) and mSATA to be "Yes"

Issue : Updated cables for VictoriaAIO, RhineAIO, and ThunAIO

System : VictoriaAIO, RhineAIO, and ThunAIO
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and conf results match hardware

Issue : Add mSATA support for Diesel 15 and 17

System : Diesel 15, Diesel 17
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On a Diesel 15 and 17 with mSATA installed run disk -conf
Expect : mSATA device to be specified.

Issue : Add PortMapping.ini file support

System : All
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : Create PortMapping.ini in WBDD directory according to PortMappings.txt.
Modify PortMapping for a platform
by creating MotherBoardPort section and entering incorrect data. Run disk
-conf.
Expect : Incorrect MotherBoardSlots based on the entries in PortMapping.Ini file.
Test #2 : Add MSATA section to PortMapping.Ini and add incorrect data for a
platform. Run disk -conf
Expect : Incorrect MSATA device specified based on the entries in PortMapping.Ini
file.

Issue : Add IDE Controller support for Slingshot

System : Slingshot
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : Run disk -conf
Expect : Controller to show as internal and slot numbers to be correct.

Issue : Exclude IPMI Fans that are physically in the Chassis from testing.
System : Stomp sleds
Impact : Factory & Customer
Modules : Fan
Authors : rods
Test #1 : Run "fan -conf"
Expect : Fans should still be listed in the config.
Test #2 : Run "fan"
Expect : Fan test should run, but only show the current RPM and then do a log
scan. Same as DCS servers.

Issue : Disk has stack corruption error with Intel driver version 12.8
System : Client
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On a client system with btoa image that has Intel driver version 12.8 run
disk -conf
Expect : Conf output returned

Issue : BITS093456 - WBDD uSFF: 'WLANcard' is 'Not Installed' in WBDD Cable Test
even w/ DW1540 card installed
System : Amazon USFF, Goodyear
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and conf results match hardware

Issue : GCF file with linefeeds instead of newlines causing buffer overrun
System : Macallan XFR
Authors : rdb
Impact : Customer & Factory
Modules : SystemConfig
Test #1 : With GCF file that has 0x0a line termination characters run systemconfig
-sil -gcf:<gcffile> -o:<silfile>
Expect : systemconfig passes and <silfile> created.

Issue : Add internal PERC H310 check for HIFI

System : HiFi
Authors : rdb
Impact : Customer & factory
Modules : Disk
Test #1 : On a Hifi run disk -conf
Expect : Embedded PERC to show ControllerInOrExt tag as Internal

Issue : Add check for future ssh_v drives using IdentifyDevice data
System : All
Authors : rdb
Impact : Factory & Customer
Modules : Disk
Test #1 : On a system with ssh-v drive that supports detection using IdentifyDevie
data run disk -conf
Expect : Commodity for device should be hard_drvie(ssh_v)

Issue : Add ST2000DX001 to ssh_v table

System : All
Authors : rdb
Impact : Factory & Customer
Modules : Disk
Test #1 : On a system with ST2000DX001 installed run disk -conf
Expect : Commodity for device should be hard_drvie(ssh_v)

Issue : Fix extra PCIE SSD controller in disk -conf

System : All
Authors : rdb
Impact : Factory & Customer
Modules : Disk
Test #1 : On a system without PCIE SSD run disk -conf
Expect : No PCIE SSD controller in conf output

Issue : HDD sensor temperature of 255C means cannot get it so changed to N/A in
WinGui
System : All
Impact : Customer & Factory
Modules : WinGUI
Authors : rdb
Test #1 : Run WinGUI with SSD installed in system
Expect : HDD sensor temp should be valid or N/A

Issue : RE-Adding initial SSID support for Avalon 3, Avalon 5, Avalon 7, Avalon R
: Change got erased with checking of changeset 6599
: Was in 6050.1 but was erased and not in 6050.3
Changset: 6541
System : Avalon 3, Avalon 5, Avalon 7, Avalon R
Modules : Cables
Authors : robib
Test #1 : Run diagnostics
Expect : no errors and conf results match hardware

Issue : BITS098660 Workmanship failure during Keyboard Test

System : All
Impact : Factory & Customer
Modules : Keyboard
Authors : RobiB
Test #1 : Run "keyboard -l[US|UK|JP|BR]
Expect : OK button on right bottom , Cancel on Left Bottom

Issue : Add EnableDIMP and DisableDIMP utilities to disk

System : All
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : Run "disk -DisableDIMP".
Expect : Pass
Test #2 : Run "disk -EnableDIMP".
Expect : Pass

Issue : Add support for Type17 DDR4 indicator. Preliminary SMBIOSCR00129.

System : All
Modules : memory
Authors : rods
Test #1 : Run "Memory -conf".
Expect : Verify dimm type is known.

Issue : Initial cables release VictoriaAIO, removed PCIEX1 detect on Tigris,

General, Great Bear
System : VictoriaAIO, Tigris, General, Great Bear
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and conf results match hardware

Issue : MDiags request "RETURN PPID/SN IN EPSA FOR HDD & MEMORY". Currently only
ePSA uses the update, but the
: affected libraries are shared with WBDD. This change is the memory
portion for servers.
Change : 6655
System : Servers
Authors : rods
Test #1 : No specific test to execute.
Expect : Modules should run same as before this change.

Issue : Battery testing indicates that charger is not installed when trickle
discharge between dual batteries.
Change :
System : Any with dual batteries and new power management chip, typically Haswell
CPU's or TSOC CPU's
Authors : carl
Test #1 : Run the battery tests. If a small discharge under 5 mA occurs, then dont'
indicate charger is not connected.
Expect : No specific message for the charger in ePSA, no test failures in WinPE.

Issue : Added string definition for thermal sensor types 6 to 10.

The indicies are in the specification, but not decoded in the code.
Change : 6886
System : All
Authors : carl
Test #1 : Run WinGUI
Expect : Thermal sensor indicies 6 to 10 to show a string and not "Other
Thermistor".
Issue : Added thermal sensor type 9 : Charger Thermistor and 10 : Back Light
Thermistor.
Change :
System : All
Authors : carl
Test #1 : Run WinGUI or EPSA
Expect : Thermal sensor 9 and 10 will show the proper string if supplied by BIOS.

Issue : Work around non-functional BIOS interface calls in Penfolds and Penmara
Requires BIOS revision A03 or later
Change :
System : Penfolds, Penmara
Authors : carl
Test #1 : Run WinDD modules
Expect : Should not see GPF of the system or blue screen during testing.
Report : If GPF or Blue Screen, document the version of the BIOS being used,
version of WinPE image
being used and the exact command line of the WinDD diagnostic being
executed (not name of script).

6050.4
-----------------------------------------------------------------------------------
----------------------------------

Issue : Fix exception in Memory test

System : ALL
Authors : bbw
Test #1 : run memory test
Expect : should not exit with exception error

6050.3
-----------------------------------------------------------------------------------
----------------------------------

Issue : Add support for testing memory above 128Gb with 64-bit WinPE
System : ALL
Modules : Memory
Authors : BBW & BJT
Test #1 : Only works with 64-bit WinPE. Requires limit to WinPE memory usage using
BCD option truncatememory set to
: 0x1000000000 and run memory on system with more than 64Gb of memory
installed
Expect : memory tested should approach amount of installed memory, test should
pass if good memory installed.

Issue : Add RAID member drives slot and port numbers to ficore output
System : Ipanema
Modules : Disk
Authors : rdb
Test #1 : On an Ipanema with LSI 9271 controller and connected devices in a RAID
run disk -ficore
Expect : last 2 fields in output to have slot and port number(s) for RAID members

Issue : Updated TigrisAIO, Name Change: Cromo->Caspian, and removed PCIEX16 slot
detect on Tigris, General, Great Bear
System : TigrisAIO, Caspian, Tigris, General, Great Bear
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and conf results match hardware

Issue : Add support for 12G SPD write interface. Currently not enabled for
general use.
Changset: 6605
System : 12G MLK (2.0.14 and later BIOS)
Modules : Eventlog. Library changes have minor affect on Memory config.
Authors : rods
Test #1 : Run "eventlog -spd".
Expect : The module should dump the SPD data as before.
Test #2 : Run "memory -conf -xml".
Expect : Verify the SPD data is included in the output as before.

6050.2
-----------------------------------------------------------------------------------
----------------------------------

Issue : Add Serial Number for LSI RAID Array devices

System : Ipanema
Modules : Disk
Impact : Factory & Customer
Authors : rdb
Test #1 : On a Ipanema with LSI 9271 RAID controller with RAID set up run Disk -
conf
Expect : Array devices under RAID controller should have a Serial NUmber

Issue : WinGUI has invalid Disk Temperature

System : All
Modules : WinGUI
Impact : Customer % Factory
Authors : rdb
Test #1 : Run WinGUI
Expect : Disk Temperature sensor should show valid temperature

6050.1
-----------------------------------------------------------------------------------
----------------------------------

Issue : FE005790 - ADC Lab-PS3-Q3PEC-Radon Z fails dst large negative error level
System : PEC, Ipanema, Bells with LSI 2008 or LSI 2308 controller with SAS
drive(s)
Modules : Disk
Impact : Factory & Customer
Authors : rdb
Test #1 : Boot system and run disk -f:1 -mon. Reboot and rerun. Do this at least 10
times.
Expect : All tests pass with no exception errors

Issue : BITS072131 WBDD: [Equinox] 6045.8 ServerMgmt.exe -conf reporting

IdracSdSize as 0
Changset: 6558
System : All (Equinox)
Modules : ServerMgmt
Authors : Robib
Test #1 : Run ServerMgmt -conf with 16 GB SD card in Vflash
Expect : no errors and conf results match hardware
Issue : Add initial SSID support for Avalon 3, Avalon 5, Avalon 7, Avalon R
Changset: 6541
System : Avalon 3, Avalon 5, Avalon 7, Avalon R
Modules : Cables
Authors : Robib
Test #1 : Run diagnostics
Expect : no errors and conf results match hardware

6049.6
-----------------------------------------------------------------------------------
----------------------------------

Issue : Haswell EX CPU needs to verify Production/Non-Production CPU

System : Equinox
Modules : SystemConfig
Impact : Factory
Authors : carl
Test #1 : Execute the System Configuration module
Expect : Entry for Production/Non-Production for the CPU
Notes : Needs to be tested on Haswell EX (Equinox), Haswell (AIO systems),
Haswell ULT (Notebook with this CPU)

Issue : Ivy Bridge EX CPU needs to verify Production/Non-Production CPU

System : Equinox
Modules : SystemConfig
Impact : Factory
Authors : carl
Test #1 : Execute the System Configuration module
Expect : Entry for Production/Non-Production for the CPU
Notes : Needs to be tested on a production CPU and a non-production CPU

Issue : LSI9271-8i controller has 30 minute time out on Unconfigured drives

System : Ipanema and Bells
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : run disk -f:8 -mon
Expect : test passes

Issue : Add Tigris to MotherBoardPortMapping table

System : Tigris
Impact : Customer & Factory
Modules : disk
Authors : rdb
Test #1 : run disk -conf
Expect : HDDs show connected to correct motherboard connector.

Issue : Add Goodyear to mSATA table

System : Goodyear
Impact : Customer & Factory
Modules : disk
Authors : rdb
Test #1 : run disk -conf
Expect : Device connected to mSATA connector should show have mSATADevice set to
yes

Issue : Orca has exception error in disk

System : Orca
Impact : Customer & Factory
Modules : Disk
Author : rdb
Test : run disk -f:2 -mon
Expect : all tests pass

Issue : DDUsbDiag.exe will issue an error for any port that is not mapped in.
Change is
to skip the port
System : Any system using the Haswell CPU
Impact : Factory
Modules : DDUsbDiag.exe
Authors : carl
Test #1 : DDUsbDiag.exe
Expect : No failure message on ports that are not mapped in for the rate matching
hubs.

6049.5
-----------------------------------------------------------------------------------
----------------------------------

Issue : Removed PCHHeatsink sensor cable test for Equinox until sensor fixed in
PT+ Boards
Change : 6471
System : Equinox
Modules : Cables
Impact : Factory
Authors : robib
Test #1 : Execute cables -conf
Expect : The PCHHeatsink sensor should not be displayed in cable configuration

6049.4
-----------------------------------------------------------------------------------
----------------------------------

Issue : Adjusted the text of the error output message so that it includes the
VID:DID of a device that fails to load.
Change : 6447
System : All
Modules : USBBist (DDUsbDiag.exe)
Impact : Factory
Authors : carl
Test #1 : Execute DDUsbDiag.exe on a system with a camera not in the INF file
Expect : The camera VID:PID to be displayed in the failure message for the device
testing.

6049.3
-----------------------------------------------------------------------------------
----------------------------------

Issue : Report Tape Density failing

System : 12G
Modules : Disk
Impact : Factory & Customer
Authors : rdb
Test #1 : On a system with LTO7 tape drive run disk -d:tbu -f:2 -mon
Expect : All tests pass

6049.2
-----------------------------------------------------------------------------------
----------------------------------

Issue : Add LTO7 tape support

System : 12G
Modules : Disk
Impact : Factory & Customer
Authors : rdb
Test #1 : On a system with LTO7 tape drive run disk -d:tbu -f:2 -mon
Expect : All tests pass

Issue : LSI9271 drive spin-down work-around

System : Ipanema
Modules : Disk
Impact : Factory & Customer
Authors : rdb
Test #1 : On an Ipanema with ST9300653SS drives connected to LSI9271 controller run
disk -f:6 -mon
Expect : All tests pass

Issue : Add NIC module to SIL

System : All
Modules : SystemConfig
Impact : Factory & Customer
Authors : rdb
Test #1 : Run SystemConfig -sil -gcf(gcffile>
Expect : MAC addresses should be in SIL output

Issue : Add Shared Service Tag support for SIL

System : All
Modules : SystemConfig
Impact : Factory & Customer
Authors : rdb
Test #1 : run SystemConfig -sil -gcf:<gcffile> -sst:1
Expect : Valid SIL output with "-1" appended to system service tag for each
instance of SerialNumber tag in output.
Test #2 : run SystemConfig -sil -gcf:<gcffile> -sst:0
Expect : Valid SIL output with no data appended to system service tag for each
instance of SerialNumber tag in output.
Test #3 : run SystemConfig -sil -gcf:<gcffile>
Expect : Valid SIL output with no data appended to system service tag for each
instance of SerialNumber tag in output.
Test #4 : run SystemConfig -sil -gcf:<gcffile> -sst:a
Expect : SystemConfig help screen

Issue : Serial module sometimes fails: Internal Loop Back Test Failed on Line
Control Verification (6048.5)
Change : 6414
System : All
Modules : Serial
Impact : Factory & Customer
Authors : marky
Test #1 : serial
Expect : Test passes

6049
-----------------------------------------------------------------------------------
----------------------------------

Issue : Added dual memory allocation methods to solve WinPE NUMA errors
(FE005215)
System : All
Modules : memory
Authors : bbw
Test #1 : Run memory diagnostics under WinPE using 32/64 bit versions
Expect : no errors

Issue : Added initial diagnostic support for Sojo, Sifi, Aqua

System : Sojo, Sifi, Aqua
Modules : Cables, et al
Authors : bbw
Test #1 : Run diagnostics
Expect : no errors and conf results match hardware

Issue : Added initial cables support for Rhine, Thun, TigrisAIO, Cromo and
updated Tigris, General, Great Bear
Change : 6069, 6214, 6249, 6277, 6287, 6288, 6312, 6313, 6409, 6410, 6411, 6416,
6417, 6429, 6451
System : Rhine, Thun, TigrisAIO, Cromo, Tigris, General, Great Bear
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and conf results match hardware

Issue : Titan 14 MLK mSATA support

System : Titan 14 MLK
Module : Disk
Impact : Factory & Customer
Authors : rdb
Test #1 : On a Titan 14 MLK with mSATA device installed run disk -conf
Expect : mSATA device output should have mSATADevice tag equal yes

Issue : Spyder causing SystemConfig -sil to hang

System : Spyder
Modules : SystemConfig
Impact : Factory & Customer
Authors : rdb
Test #1 : Run SystemConfig -sil
Expect : SIL output with out system hanging

Issue : Add check for recursive call limit in xmlparser

System : All
Modules : SystemConfig
Impact : Factory & Customer
Authors : rdb
Test #1 : On a system with greater than 887 entries in a GCF container run
SystemConfig -sil -gcf:<gcf file>
Expect : Valid SIL output

Issue : Add client PCIe SSD support

System : Bells7
Modules : disk
Impact : Factory & Customer
Authors : rdb
Test #1 : On A Bells 7 with PCIe SSD card installed run disk -conf
Expect : PCIe SSD device to be displayed in conf output

Issue : PCIe SSD drive is showing up 2x in disk -conf and as a HDD in disk -
ficore
System : Mojo
Modules : disk
Impact : Factory & Customer
Authors : rdb
Test #1 : On a Mojo with PCIe SSD run disk -conf
Expect : PCIe SSD should only show up under PCIe Bridge Card in conf
Test #2 : On a Mojo with PCIe SSD run disk -ficore
Expect : PCIe SSD should show up as PCIESSD device

Issue : SystemConfig reports Add-in GPGPU as embedded

System : Plasma
Modules : SystemConfig
Impact : Factory & Customer
Authors : rdb
Test #1 : run systemconfig -d:misc on Plasma with GPGPU add-in card
Expect : Card should show up with 2 PCI IDS as add-in. Only true add-in cards
should be specified as add-in

6048.5
-----------------------------------------------------------------------------------
----------------------------------

Issue : SystemConfig has exception error when GCF file does not have line
termination characters (\n)
System : All
Modules : SystemConfig
Impact : Factory & Customer
Authors : rdb
Test #1 : run SystemConfig -sil -gcf:<GCF file with no CRLFs in body of XML file>
Expect : SIL output and no exception error

6048.4
-----------------------------------------------------------------------------------
----------------------------------

Issue : SystemConfig reports embedded PCIID as Add-in

System : Derby
Modukes : SystemConfig
Impact : Factory & Customer
Authors : rdb
Test #1 : run systemconfig -d:misc
Expect : only true add-in cards to specified as add-in

Issue : SystemConfig has exception error when GCF file has tiedigitalactivations
container
System : All
Modules : SystemConfig
Impact : Factory & Customer
Authors : rdb
Test #1 : run SystemConfig -sil -gcf:<GCF file with tieddigitalactivations
container>
Expect : SIL output and no exception error

6048.3
-----------------------------------------------------------------------------------
----------------------------------

Issue : Unitialized class variable causes exception error

System : All
Modules : disk
Impact : Factory & Customer
Authors : rdb
Test #1 : run disk -conf
Expect : configuration output with no exception errors

Issue : Microsoft issue with LSI driver and amount of system memory causes mode 5
HDD flash failure
System : Plasma
Modules : disk
Impact : Factory & Customer
Authors : rdb
Test #1 : On a Plasma run disk -hddflash -fwdir:<fw directory>
Expect : Drives should be updated to latest fw rev in fwdir

6048.2
-----------------------------------------------------------------------------------
----------------------------------

Issue : Incrememts lba counter by 1 instead of 0x40 for SequentialSeek Test

System : All
Modules : disk
Impact : Customer & Factory
Authors : rdb
Test #1 : Run disk -f:6 -mon
Expect : All test pass

Issue : Added initial cables support for Rhine

System : Rhine
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and conf results match hardware

Issue : Added test number and test progress to each disk device sensor in Disk
Module Process Area of Shared Memory
System : All
Modules : disk
Impact : Factory & Customer
Authors : rdb
Test #1 : run disk -f:1 -mon. In another command window run smviewer.
Expect : smviewer response to show 3 bytes that contain temperature (byte 0),
percent of test complete (byte 1) and
: test number (byte 2). Byte 2 will change when test changes. Byte 1 will
update every 10 seconds with the
: test progress.

6048
-----------------------------------------------------------------------------------
----------------------------------

Issue : BITS085643 WBDD 6047.10 Cables.exe reports InternalStorageAdapter

NotInstalled when NDC Riser is not installed
System : Equinox
Modules : Cables
Impact : Customer & Factory
Authors : robib
Test #1 : Run cables -conf ; cables -details
Expect : InternalStorage Adapter status correct with NDC installed or Uninstalled
Issue : Hitachi HDDs failing firmware flash when filesize is exact multiple of
32K
System : Plasma
Modules : Disk
Impact : Customer & Factory
Authors : rdb
Test #1 : On a Plasma with Hitachi drive run disk -hddflash -backflash
Expect : Drive to flash back toprevious rev
Test #2 : On a Plasma with Hitachi drive run disk -hddflash
Expect : Drive to flash to current rev

Issue : MTDL request to output HDD PPID on failure

System : All
Modules : Disk
Impact : Customer & Factory
Authors : rdb
Test #1 : On a system with hdd failure run disk -f:1 -mon -xml
Expect : Details message with format <Details>[Device]:
PPID_SN:[PPID/SN]</Details>

Issue : BITS071971 WBDD 6045.8 cables.exe reports PwrSply[1,2,3,4] NotInstalled

System : Equinox
Modules : Cables
Impact : Customer & Factory
Authors : robib
Test #1 : Run cables -conf ; cables -details
Expect : PSU2/PSU3/PSU4 should report dynamic reading if PSU removed

Issue : LSI 2308 controller causing system exception error on first test after
boot with SAS drives connected
: to 2308 controller.
System : Ipanama and Bells 7
Modules : Disk
Impact : Customer & Factory
Authors : rdb
Test #1 : run disk -f:5 -mon after booting system
Expect : all tests shopuld pass.

Issue : Add UTC to SIL Date field, change SIL xml encoding value to UTF-8 and
change ProductFamily field
: from Drive to HardDrive per SIL pec 2.04.
System : All
Modules : SystemConfig
Impact : Customer and Factory
Authors : rdb
Test #1 : run SystemConfig -sil -gcf:<gcf file> -o:test.xml
Expect : test.xml output to follow System Inventory Specification

Issue : Update IPMI initialization routine to issue a message if the "winIPMIdll"

file is missing. This check
: only happens after smbios has indicated the presence of an IPMI
interface.
Change : 5970
System : Servers
Modules : Fan
Impact : Customer & Factory
Authors : rods
Test #1 : Rename "winipmidll.dll" to something else and run "ServerMgmt".
Expect : Should receive a message about the misssing file.
Test #2 : Restore "winipmidll.dll" and run "servermgmt".
Expect : Normal behavior.

Issue : Update IPMI Fan to use the first failing eventlog message as the text
instead of a generic
: message referring to events in the log.
Change : 5971
System : Servers
Modules : Fan
Impact : Customer & Factory
Authors : rods
Test #1 : Run "Fan"
Expect : If the module fails due to an eventlog message, the Result should contain
the first message. Other
: messages will continue to be displayed as part of the "details" in the
test output.

Issue : BITS083851 BITS � ST_OAKH:HDD controller test show error when run
wingui.exe in WBDD6047.
System : Oak
Modules : Disk
Impact : Customer & Factory
Authors : rdb
Test #1 : Run WinGI. Select HDD Controller and run test
Expect : WinGUI output to say "No test available for this device"

Issue : Ipanema with SAS drives having exception error on first test run after
boot
System : Ipanema
Modules : disk
Impact : Customer & Factory
Authors : rdb
Test #1 : Boot to WinPE. Run Disk -f:5 -mon
Expect : All tests should pass

Issue : Remove Backplane Signal1 Cable sensor - only BP Signal0 implemented for
all BP configs
System : Equinox
Modules : Cables
Authors : RobiB
Impact : Customer & Factory
Test #1 : cables -conf
Expect : Should display correct BP Power (2) and BP Signal (1)

Issue : CFI GCF creation utility gcf files causing XML parser errors for SIL
generation
System : CFI test systems
Modules : SystemConfig
Authors : rdb
Impact : Customer & Factory
Test #1 : On a system that has had gcf file created using cfi gcf utility run
systemconfig -sil -gcf:<filename> -o:SIL.xml
Expect : SIL.xml to be created with valid information

Issue : Fixes HDD PPID not being displayed for SATA drives connected to Intel
controller
System : All with Intel disk controller
Modules : disk
Authors : rdb
Impact : Customer & Factory
Test #1 : On a system with HDDs connected to Intel controller run disk -conf
Expect : HDD PPID to be in conf output

Issue : Add setting and retrieving EFI variable under Windows

System : All
Modules : SystemConfig
Authors : rdb
Impact : Customer & Factory
Test #1 : On a system with EFI boot enabled, boot to Win8 PE and run systemconfig -
bv -store
Expect : expect no errors
Test #2 : On same system after running above run systemconfig -bv -restore
Expect : Build Verify to pass

Issue : Add cable detection items for ICON:

System : ICON, OEM_ICON, ICON_UNISYS
Modules : cables
Authors : hw
Impact : Customer & Factory
Test #1 : Run cables.exe -conf on ICON
Expect : verify status for IDSDM (rips presence), Nic daughter card presence, TPM
type, TPM plug in module status
: Front usb cable, Front VGA cable, Front LCD cable, VFlash card presence,
Riser 1, riser 2, riser 3 presence

Issue : Invalid entry in mSATA table for Salado 14 HSW

System : Salado 14 HSW
Modules : disk
Authors : rdb
Impact : Customer & Factory
Test #1 : On a Salado 14 HSW with mSATA device that does not have mSATA in the
description run disk -conf
Expect : mSATA device should show up in conf output

Issue : Exception error occurring in Tulum when discovering RAID information

System : Tulum
Modules : disk
Authors : rdb
Impact : Customer & Factory
Test #1 : On a Tulum with RAID run disk -conf
Expect : No exception error. RAID information may not be displayed

Issue : Remove drive temperature collection during HDD Fw update

System : Plasma
Modules : disk
Authors : rdb
Impact : Customer & Factory
Test #1 : Run disk -hddflash -fwDir:<fw directory>
Expect : Drive fw to be updated

Issue : Fix issue with Plasma HDD flash due to Microsoft limitation with amount
of memory in system
System : Plasma
Modules : Disk
Authors : rdb
Impact : Customer & Factory
Test #1 : Run disk -hddflash -fwDir:<fw directory>
Expect : Drive fw to be updated

Issue : Add support for SPD via Bios/Diags interface.

System : All
Modules : Memory, EventLog
Authors : rods
Test #1 : Run "memory -conf -xml" on 12G server with Dell bios or Amazon.
Expect : Output should include the SPD information for each installed dimm.
Test #2 : Run "eventlog -spd" on 12G server with Dell bios or Amazon.
Expect : Output should include the SPD information for each installed dimm.

Issue : Add Disk Functional Test Block patching

System : All
Modules : Disk
Authors : rdb
Test #1 : get password from disk.rc, run disk -gen -f:1 -d:hdd -rem:Verify -
pw:<password>
Expect : disk.rmt to be created in current directory
Test #2 : run disk -f:1 -mon
Expect : Verify test should not be run, all other tests should pass

Issue : Make Intruder cable detect optional for PalmBeachAIO

System : PalmBeachAIO
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and conf results match hardware

Issue : BITS078974 - workaround to fix detection of PS1, PS2,PS3, PS4 and PERC1 .
IDRAC removed/changed sensors and
: gave it to Memory Risers.
System : Equinox
Modules : Cables
Authors : robib
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and conf results match hardware for PS1, PS2, PS3, PS4, PERC1

Issue : Added initial cables support for General and Tigris

System : General, Tigris, Great Bear
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and conf results match hardware

Issue : Enable NVidia/AMD Notebook Panel Test in secure boot mode.

System : Notebooks
Modules : NBPanel
Impact : Customer & Factory
Authors : mikel
Test #1 : Run NBPanel tests.
Expect : Panel test should instantiate and complete with error.

Issue : Fix DMI eventlog scan to ignore a buffer of 64K - found to be invalid.
Change : 5476
System : All
Modules : Eventlog
Impact : Customer & Factory
Authors : rods
Test #1 : Run tests as normal.
Expect : No change in functionality.

Issue : Added initial support for Haywire (SYS_HAYWIRE) (Server based on Tulum)
Issue : Added initial support for GENERAL_MT (GENERAL_MT_N).
General has one SSID for the DT and SFF system, and a new separate SSID
for the MT version.
Change : 5955
System : Haywire, General MT
Modules : Cables
Impact : Factory
Authors : carl
Test #1 : Run cables test on platform.
Expect : Cables to be detected for this SSID.

Issue : Add cable support for fast track server code named Haywire.
Change :
System : Haywire
Modules : Cables
Authors : carl
Test #1 : Run "psa -wait"
Expect : Verify that Cables shows valid tests for the system.

Build 6047.7
-----------------------------------------------------------------------------------
----------------------------------

Issue : Work-around for Haswell chipset / Intel driver issue with ODD read test
System : All
Modules : disk
Impact : Factory & Customer
Authors : rdb
Test : Run disk -d:cdrom -f:6 -mon
Expect : Test should pass

Build 6047.6
-----------------------------------------------------------------------------------
----------------------------------

Issue : Work-around for Haswell chipset / Intel driver issue with ODD tray test
System : All
Modules : disk
Impact : Factory & Customer
Authors : rdb
Test : Run disk -d:cdrom -f:5 -mon -ix
Expect : Test should pass

Build 6047.5
-----------------------------------------------------------------------------------
----------------------------------

Issue : Disk -MediaPresence not reporting correct errorlevel when media is not
installed
System : All
Modules : disk
Impact : Factory & Customer
Authors : rdb
Test : With media not installed run disk -d:cdrom -MediaPresence
Expect : Test should fail with errorlevel 1
Build 6047.4
-----------------------------------------------------------------------------------
----------------------------------

Issue : SSH_P connected to Oak 15 HSW in AHCI mode not displaying as

hadr_drive(ssh_p)
System : All
Modules : disk
Impact : Factory & Customer
Authors : rdb
Test : On an Oak 15 HSW with Hybrid SSH_P HDD run disk -conf
Expect : Commodity should be hard_drive(ssh_p)

Build 6047.3
-----------------------------------------------------------------------------------
----------------------------------

Issue : RD1000 in Coaste with ficore image 803_03a or 803_03s does not appear
correctly in disk -conf output
System : Coaster
MOdules : Disk
Impact : Customer & Factory
Authors : rdb
Test #1 : On Coaster with RD1000 running ficore version 803_03s001 run disk -conf
Expect : RD1000 to shgow up in conf output

Build 6047.2
-----------------------------------------------------------------------------------
----------------------------------

Issue : Fix exception error caused by non-Dell drive

System : Ghostrider
Modules : disk
Impact : Factory & Customer
Authors : rdb
Test #1 : On a Ghostrider with non-Dell drive run disk -conf
Expect : Coorect config output with no exception error

Issue : Corrected SIL output tag for memory

System : All
Modules : SystemConfig
Impact : Customer & Factory
Authors : rdb
Test #1 : Run SystemConfig -sil -gcf:<gcffile>
Expect : Memory section of SIL should have <MFGLOC> tag

Issue : Center Riser identification (Option 1 & Option 2) is reversed

System : Ipanema
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and conf results match hardware

Build 6047
-----------------------------------------------------------------------------------
----------------------------------

Issue : BITS075554 WBDD 6045.8 cables.exe does not report BP Signal information
System : Equinox
Modules : cables
Impact : Customer & Factory
Authors : robib
Test : run cables -conf
Expect : should show BP0power BP1power and BP0Signal BP1Signal capabilities

Issue : Add SSH_P and SSH_V as disk types for ficore output
System : All
Modules : disk
Impact : Factory & Customer
Authors : rdb
Test : On a system with Hybrid HDD runb disk -ficore
Expect : Depending on type of Hybrid drive either SSH_P or SSH_V should be
displayed in output

Issue : Added OEM Cables support

System : Telstra, Fleming, Teva
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and conf results match hardware

Issue : BITS071951 WBDD encounters Memory failure on Equinox with 60 CPU's ( 4

CPU * 15 core )
System : all
Modules : memory
Impact : Factory
Authors : bbw
Test : run memory -f:1
Expect : should pass, except if memory errors detected or WinPE 32-bit on Equinox

Issue : ODD returning invalid SerialNumber offset causing disk to get an

exception error
System : BMW
Modules : disk
Impact : Factory & Customer
Authors : rdb
Test : On a BMW run disk -conf
Expect : System should pass

Issue : BITS0712167: NDC Riser message inconsistent with RIPS/IDSDM printed on

confoguration page.
System : Equinox
Modules : Cables
Imapct : Customer & Factory
Authors : robib
Test : Run cables -conf
Expect : Should say NDC Riser

Issue : System Health shows Battery Health as n/a (Corse XPS-18)

System : All notebooks and AIO that have batteries (Corse XPS-18)
Modules : Battery
Imapct : Customer & Factory
Authors : vinodm
Test #1 : battery -conf
Expect : Check Battery Health, should not say n/a

Issue : BITS072137: Wrong message for riser being printed out in cables.
System : Equinox
Modules : Cables
Imapct : Customer & Factory
Authors : robib
Test : Run cables -conf after Right IO Riser removed
Expect : Should say Right IO Riser Missing

Issue : BITS0712167: NDC Riser message inconsistent with RIPS/IDSDM printed on

confoguration page.
System : Equinox
Modules : Cables
Imapct : Customer & Factory
Authors : robib
Test : Run cables -conf
Expect : Should say NDC Riser

Issue : Change method to get System ID and OEM System IDs for cables
System : All
Modules : Cables
Imapct : Customer & Factory
Authors : rdb
Test : On a Summit run Cables
Expect : Test should pass
Test : On an Orca run Cables
Expect : Test should pass

Issue : Update ServerMgmt FRU dump to continue even if a non-responsive FRU is

found.
System : Servers with IPMI
Modules : ServerMgmt
Impact : Factory & Customer
Authors : rods
Test : run "servermgmt -conf" or "servermgmt -frudump".
Expect : The output should include all the FRUs defined in the IPMI SDR. Even
those that do not respond correctly
: should have a couple of lines describing why.

Issue : BITS072176: LC Diags 94Y8H X01-00. The TPM manufactures name is spelled
incorrectly.
System : All
Modules : Cables
Impact : Factory & Customer
Authors : robib
Test : run cables -conf and cables -details
Expect : TPMNuvuton should be corrected as TPMNuvoton

Issue : BITS FE004128 - Indy -Error setting NIC=DEDICATED

System : Vince/Indy
Modules : Cables
Impact : Factory & Customer
Authors : robib
Test : run cables -conf
Expect : AMEARiser should be detected

Issue : Ficore output incorrect for new Intel driver version 12.0.0.1038
System : All with Intel Chipset that uses iaStorA driver
Modules : Disk
Impact : Factory & Customer
Authors : rdb
Test : run disk -ficore
Expect : Correct information to be displayed for each PhysicalDrive

Issue : Hard drive commodity type hard_drive(ssh_v) not showing up for Kahuna_V
drives
System : Desktops and Notebooks
Modules : Disk
Impact : Factory & Customer
Authors : rdb
Test : run disk -conf on system with Kahuna_V drive
Expect : Commodity should be hard_drive(ssh_v)

Issue : Add Details xml tag for MDiags messaging requirements

System : All
Modules : All
Impact : Customer & Factory
Authors : rdb
Test #1 : For a Module that has uses new function and has a failure, run test with
-xml switch
Expect : <Details> tag to be in xml output

Issue : Fix support for 512e and 4k sector size drives

System : All
Modules : Disk
Impact : Customer & Factory
Authors : rdb
Test #1 : On a system that has 512e and/or 4k sector size drives, run disk -conf
Expect : DriveSectortype should be set to 512e, 4k or 512n depending on drive
type.

Issue : Add support for MDiags messaging requirements to Disk

System : All
Modules : Disk
Impact : Customer & Factory
Authors : rdb
Test #1 : On a system that fails disk, run test with -xml output
Expect : Details tag should contain messages explaining failure. Only one Results
tag per drive should be displayed.

Issue : Change correctable ECC log entry from Warning to Critical.

Change : 5090
System : All with IPMI event log
Modules : Memory, ServerMgmt
Authors : Rods
Test #1 : Run memory test. A bad dimm will be required to test the error without
modifying the test.
Expect : ECC will be reported as a Critical error and the test should stop.

Issue : Fixed mSATA and WLAN miniCard detection

System : Monster HSW
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and conf results match hardware

Issue : Add system IDs to support OEM XL Bluefish, Diamas Riverbed, Diamas Trend
and Diamas Avaya
: BITS072950 Diamas OEMR XL order fail in QT cables build verify.
: FE004167 BTO/FACE � WBDD: DAO - FSJ - - 11G - BLUEFISH - CABLES FAIL
System : Diamas and Bluefish
Modules : Cables
Impact : Customer & Factory
Authors : hw
Test #1 : run cables.exe on the OEM Diamas to be supported
Expect : verify that cable status are reported correctly

Issue : Add PPID collection for drives connected to PERC controller

System : Servers & WorkStations
Modules : Disk
Impact : Customer & Factory
Authors : rdb
Test #1 : run disk -conf on a system with PERC controller
Expect : Drive PPID to be in conf output

Issue : Drives showing up 2x on PLASMA with Dual controllers

System : Plasma
Impact : Customer & Factory
Authors : rdb
Test #1 : On a Plasma with Dual PERC run disk -conf
Expect : Same drives with same Mnemomics to show up under each controller
Test #2 : On a Plasma with Dual PERC run disk -f:1 -mon
Expect : All test should pass

Issue : System Inventory List Addition

System : All
Modules : SystemConfig
Impact : Customer & Factory
Authors : rdb
Test #1 : run SystemConfig -sil -gcf:<gcf file> -o:test.xml
Expect : test.xml output to follow System Inventory Specification

Issue : BITS068522:DAO - PS3 - ADC_LAB - 11G Thidwick XLR - BV - Buildverify:

Cables failed
: Testing with new SSID's 0x811A and 0x811C (TIPS Changeset: 4972)
System : Thidwick
Modules : Cables
Impact : Factory & Customer
Authors : Haiming and Robi
Test #1 : Run cables -conf
Expect : Tests should Pass

Feature : Performance enhancement to reduce any chances of possible memory

fragmentation. Adds support
: for SMBIOS interface cbClass = 5.
System : All
Modules : DDDriver.sys
Impact : Factory & Customer
Authors : bjt
Test #1 : All all test modules.
Expect : Verify that all the test modules function correctly.

Issue : BITS041589 - Media bay battery health shows "n/a" in system health of
ePSA.
System : Dalmore and other that allow for two batteries
Modules : Battery
Authors : vinodm
Test #1 : Run "battery -conf" on a notebook with two batteries
Expect : Battery Health should display correctly for both batteries
Test #1 : Run "battery -conf" on a notebook with one battery
Expect : Battery Health should display correctly for one battery

Issue : Update LSI storelib libraries to version 7.20

System : All with LSI/PERC controllers
Modules : Disk
Impact : Factory & Customer
Authors : rdb
Test #1 : On system with PERC controller run disk -conf
Expect : All controllers and drives should be displayed
Test #2 : On a system with PERC controller run disk -f:1 -mon
Expect : All tests should pass

Build 6046.9
-----------------------------------------------------------------------------------
----------------------------------

Issue : Center Riser Detection is incorrect because Detect and Presence bits are
swapped
System : Ipanema
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and conf results match hardware

Issue : Removed PassWord and MFG Jumpers, No ARD Requirement

System : Monster-HSW, Monster-IVB
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and conf results match hardware

Issue : BITS066711: Bios does not report correct FAN names when displaying FANS
in ePSA for BELLS 7, BELLS 5, BELLS 3
(Skip PSU Fans in Diags)
System : BELLS
Modules : Fan
Authors : robib
Test #1 : Run ePSA
Expect : Power Supply Fans should not get displayed

Build 6046.8
-----------------------------------------------------------------------------------
----------------------------------

Issue : Added Amazon X OEM chassisID support

System : Amazon X OEM
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and conf results match hardware

Issue : Updated Ipanema PAID

System : Ipanema
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and conf results match hardware

Issue : Added USB vid/pid for 05ca:1821

System : Mariner, Ranger
Module : DDusbdiag
Impact : Factory
Authors : mikel
Test #1 : run DDusbdiag.exe
Expect : test should run Webcam UBIST and pass

Build 6046.7
-----------------------------------------------------------------------------------
----------------------------------

Issue : Exception occurring in fMsg

System : Plasma
Module : Disk
Impact : Factory & Customer
Authors : rdb
Test #1 : run disk -f:10 -mon
Expect : test should pass

Issue : Software RAID systems not displaying HDD PPID

System : Servers with SWRAID
Module : Disk
Impact : Factory & Customer
Authors : rdb
Test #1 : On a system with SWRAID run disk -conf
Expect : Disk PPDI should be displayed

Build 6046.6
-----------------------------------------------------------------------------------
----------------------------------

Issue : System Inventory List did not display System ID and Trackcode
System : All
Module : SystemConfig
Impact : Factory & Customer
Authors : rdb
Test #1 : run SystemConfig -sil -gcf:<gcf file> -o:test.xml
Expect : SystemID and TrackCode should be displayed in SIL output

Build 6046.5
-----------------------------------------------------------------------------------
----------------------------------

Issue : System Inventory List did not set return code

System : All
Module : SystemConfig
Impact : Factory & Customer
Authors : rdb
Test #1 : run SystemConfig -sil -gcf:<gcf file> -o:test.xml
Expect : errorlevel of 0

Issue : Added Ipanema PAID and changed Amazon X chassisID

System : Ipanema, Amazon X
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and conf results match hardware

Issue : BITS068295 : DAO-PS3-12G-SLICE-Cables BV Failure with DD 6045.5

System : Slice
Modules : Cables
Impact : Factory & Customer
AUthors : rdb
Test #1 : Run cables -conf
Expect : Risers should RiserD and RiserF

Build 6046.4
-----------------------------------------------------------------------------------
----------------------------------

Issue : Update PCIe SSD libraries

System : All with PCIe SSD
Modules : Disk
Impact : Factory & Customer
Authors : rdb
Test #1 : On system with PCIe SSD devices run disk -conf
Expect : All controllers and drives should be displayed
Test #2 : On a system with PCIe SSD devices run disk -f:1 -mon
Expect : All tests should pass

Build 6046.3
-----------------------------------------------------------------------------------
----------------------------------

Issue : Updated Monster HSW-SSI/IVB-PT and AndromedaR2 miniPCIE detection Cables

test
System : Monster-HSW, Monster-IVB, AndromedaR2
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and conf results match hardware

Issue : Added OEM Northshore cables and Amazon X support

System : OEM North Shore, OEM North Shore XL, OEM Amazon X OEMR BIOS, OEM CME
custom Amazon X
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and conf results match hardware

Issue : Update hard drive commodity to include ssh_v and ssh_p

System : All
Modules : Disk
Impact : Factory & Customer
Authors : rdb
Test #1 : On a system with value hybrid drives run disk -conf
Expect : Commodity type to be hard_drive(ssh_v)
Test #1 : On a system with performance hybrid drives run disk -conf
Expect : Commodity type to be hard_drive(ssh_p)

Build 6046
-----------------------------------------------------------------------------------
----------------------------------

Issue : Updated cable support to PT

System : MonsterAIO, MonsterAIO HSW, AndromedaR2
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and conf results match hardware

Issue : Additional entries for Bells - intruderswitchcable and auxled

System : Bells7
Module : Cables
Impact : Customer & Factory
Authors : robib
Test #1 : cables -conf
Setup : Install intruderswitch
Expect : Tests should pass.

Issue : Equinox cables changes - removed CPLD version GPIO and made some Optional
System : Equinox
Module : Cables
Impact : Customer & Factory
Authors : robib
Test #1 : cables -conf
Expect : Tests should pass.

Issue : Fix deleted Changset# 3097 back in TIPS

System : BSLSN
Module : Cables
Impact : Customer & Factory
Authors : robib
Test #1 : cables -conf
Expect : Tests should pass.

Issue : Add CPU Nominal Speed string from the CPUID per MDiags request.
System : All
Module : SystemConfig
Impact : Customer & Factory
Authors : cca
Test #1 : run systemconfig
Test #2 : run systemconfig -xml
Expect : Displays the CPU speed string from the CPUID on Intel, or UNSUPPORTED on
all other CPU's.

Issue : Add MotherboadMapping support for Bells7

System : Bells7
Module : Disk
Impact : Customer & Factory
Authors : rdb
Test #1 : With ODD installed run disk -conf.
Expect : ODD should be in MotherBoardSlot 0 or 1 depending on where cable is
installed.

Issue : Add initial support for Sojo, Sifi and Aqua

System : Sojo, Sifi, Aqua
Module : Cables
Impact : Factory & Customer
Authors : bbw
Test #1 : cables -conf and cables -details
Expect : Tests should Pass

Build 6045
-----------------------------------------------------------------------------------
----------------------------------
Issue : Add-in NIC cards all have pci slot set to 0
System : Derby
Module : SystemConfig
Impact : Customer & Factory
Authors : rdb
Test #1 : run systemconfig -d:misc
Expect : Add-in cards should have PCISlot tag not equal to 0

Issue : Added HDD Controller check for add-in device

System : Derby
Modules : SystemConfig
Author : rdb
Impact : Factory & Customer
Test #1 : Run SystemConfig -d:misc on Derby
Expect : Internal AHCI controller to not be Add-in card

Issue : Exception caused by incorrect string size in SystemConfig build

verification
System : Orca
Modules : SystemConfig
Author : rdb
Impact : Factory & Customer
Test #1 : On an ORCA with large numnber of DIMMS that do not match the GCF file run
systemconfig buildverify
Expect : System to fail without an exception.

Issue : Add blue ray commodity types to disk -conf output

System : All
Modules : disk
Author : rdb
Impact : Factory & Customer
Test #1 : On a system with Blue Ray combo drive run disk -conf
Expect : Expect commodity type to be dvdrw_drive(bluray_read_only)
Test #1 : On a system with Blue Ray writer run disk -conf
Expect : Expect commodity type to be dvdrw_drive(bluray)

Issue : Fix issue where expander failed getting GLIST

System : All
Modules : disk
Author : rdB
Impact : Factory & Customer
Test #1 : On a system with an expander run disk -conf
Expect : Conf output with no errors

Issue : Updated driver certificates.

System : All
Modules : Dddriver.sys, DDUsbDriver.sys, Usbbist.cat
Author : bjt
Test #1 : Ddusbdiag.exe
Expect : All tests should pass.
Test #1 : Fan.exe
Expect : Test should pass.

Issue : Pickup Changset 4552 from RelBranch6044A1 that fixes Keyboard custom keys
display
System : Notebooks
Modules : Keyboard
Author : robib
setup #1 : Keyboard -kl and save some Custom keys i.e. Avenger MLK
Test : Keyboard -klKeyLogScan.txt
Expect : Should display only Custom keys from Log file. Other Fn+combination keys
should be disabled

Issue : Modify hard drive commodities per CR BITS053286

System : All
Modules : Disk
Author : rdb
Test #1 : On a system with SED/FDE drive run disk -conf
Expect : commodity should be hard_drive(fde)

Issue : Add cables tests for Corse

System : Corse
Modules : Cables
Authors : Mikel
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and conf results match hardware

Issue : Changed Intruder Cable detect from Required to Optional

System : Amazon9, AmazonX, Tulum
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and conf results match hardware

Issue : Updated cable support to PT, added Board REV detection

System : MonsterAIO
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and conf results match hardware

Issue : Added minicard detection

System : AndromedaR2
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and conf results match hardware

Issue : Add GLIST Count tag to disk -conf output for HDDs
System : All
Module : Disk
Impact : Factory & Customer
Authors : rdb
Test #1 : run disk -conf
Expect : GListTag to be in HDD conf outout

Issue : Add initial support for Bells3, Bells5, Bells7

System : T3610,T5610,T7610
Module : Cables
Impact : Factory & Customer
Authors : robib
Test #1 : cables -conf and cables -details
Expect : Tests should Pass

Issue : Amazon 9 mSATA support

System : Amazon 9
Module : Disk
Impact : Factory & Customer
Authors : rdb
Test #1 : On an Amazon 9 USFF with mSATA device installed run disk -conf
Expect : mSATA device output should have mSATADevice tag equal yes

Issue : Andromeda R2 mSATA support

System : Andromeda R2
Module : Disk
Impact : Factory & Customer
Authors : rdb
Test #1 : On an Andromeda R2 with mSATA device installed run disk -conf
Expect : mSATA device output should have mSATADevice tag equal yes

Issue : Optiarc optical device has space in devicetype returned by device.

System : Negril
Module : Disk
Impact : Factory & Customer
Authors : rdb
Test #1 : With Optiarc DVD RW installed run disk -conf
Expect : Conf output should show DVD RW device

Build 6044.2
-----------------------------------------------------------------------------------
----------------------------------

Issue : Orca XD with 10 Hitachi drives failing for timer error

System : OrcaHD
Module : Disk
Impact : Factory & Customer
Authors : rdb
Test #1 : Run disk -f7 -mon with 10 Hitachi drives intalled
Expect : Test should pass on all drives

Issue : Add HDD firmware flashing for Plasma

System : Plasma
Module : Disk
Impact : Factory & Customer
Authors : rdb
Test #1 : Run disk -HDDFlash -mon -FwDir:<fw file directory> -Forceflash
Expect : FW should be flashed on all SAS HDDs connected to PERC controllers

Build 6044.1
-----------------------------------------------------------------------------------
----------------------------------

Issue : BITS057381: Add functionality for displaying Keyboard from scanlog

template file
System : Notebooks
Modules : Keyboard
Authors : robib
Test #1 : Run commmand: Keyboard.exe -kl and select Keys. Use menu option
SaveKeyLog to save scan codes
Expect : Scan codes saved in default file KeyLogScan.txt in working directory
Test #2 : Run commmand: Keyboard.exe -klKeyLogScan.txt
Expect : Keyboard should display and highlight the same keys that were selected in
test#1 above (visual test)
Expect : Number of keys displayed should match number of scan codes in
KeyLogScan.txt file
Issue : Added or updated cable support, added AmazonAIO Board REV detection,
added minicard detection
System : MonsterAIO, PirelliAIO, PalmBeachAIO, AmazonAIO, Amazon9, AmazonX, Tulum,
Goodyear, AndromedaR2
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and conf results match hardware

Issue : Goodyear has incorrect slot for mSATA when RAID is set up
System : Goodyear
Module : Disk
Impact : Factory & Customer
Authors : rdb
Test #1 : On a Goodyear with RAID on mSATA device run disk -conf
Expect : mSATA device slot should be slot 5
Test #2 : On a Goodyear without RAID on mSATA device run disk -conf
Expect : mSATA device slot should be slot 5

Issue : Plasma unable to find tests for HDDSAS devices

System : Plasma
Module : Disk
Impact : Factory & Customer
Authors : rdb
Test #1 : On a Plasma with SAS drives connected to external controller run disk -
f:1 -d:HDDSAS -mon
Expect : all tests pass

Issue : Systems with SWRAID have multiple "ControllerInOrExt" tags

System : Servers with SWRAID
Module : Disk
Impact : Factory & Customer
Authors : rdb
Test #1 : On a server with SWRAID run disk -conf
Expect : Only one tag for ControllerInOrExt

Build 6043.5
-----------------------------------------------------------------------------------
----------------------------------

Issue : Merged changset 4292 from Src to fix Cables issue for single bit signals
System : All
Module : Cables
Impact : Factory & Customer
Authors : bill/carl
Test #1 : cables -conf
Expect : tests should pass

Issue : USBDiag not having a xml MSG close tag

System : Milky Way
Module : USBDiag
Impact : Factory & Customer
Authors : rdb
Test #1 : Run USBDiag -conf -xml on Milky Way mulitple times.
Expect : There should be a </Msg> tag at the end of the output.

Build 6043.4
-----------------------------------------------------------------------------------
----------------------------------
Issue : Cables giving exception on Pirelli AIO system while generating PPID
System : Pirelli AIO
Module : SmbiosLib
Impact : Factory & Customer
Authors : robib
Test #1 : On Pirelli run Cables -conf
Expect : Tests should pass

Issue : Added support for two pin LVDS Cable detect, Changed Converter cable and
removed TPM on AmazonAIO
System : Pirelli, AmazonAIO
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and conf results match hardware

Issue : Virtual Drives not showing up as RAID device in disk

System : Expansler
Module : disk
Impact : Factory and Customer
Authors : rdb
Test # : On an Expansler with RAID run disk -conf
Expect : Stand-alone HDD (one not associated with a controller) should have Device
Type of RAID

Issue : Internal PCI Bridges showing up as Add-In devices in systemconfig

System : Expansler
Module : SystemConfig
Impact : Factory & Customer
Authors : rdb
Test #1 : On an Expansler run SystemConfig -d:misc
Expect : Internal PCI Bridges should have AddInDevice equal to No

Issue : BITS053843 Add cables support for Shamu to WBDD 6043

System : Shamu, OEM Ready Orca
Module : cables
Impact : Factory & Customer
Authors : haimingw
Test #1 : Run "cable -conf" on a Shamu system
Expect : Verify all cables status are correctly reported

Build 6043.3
-----------------------------------------------------------------------------------
----------------------------------

Issue : Picked up 64-bit ddriver.sys timestamp version from Bryan

System : All
Module : All 64-bit
Impact : Factory & Customer
Authors : bryant
Test #1 : cables -details
Expect : Driver should load. Tests should Pass.

Build 6043.2
-----------------------------------------------------------------------------------
----------------------------------

Issue : Merge Touchpad.rc manually due to issues in original build merge

System : Notebooks
Module : Touchpad
Impact : Factory & Customer
Authors : robib
Test #1 : Touchpad
Expect : Tests should Pass. ESC should prompt for Abort.

Build 6043.1
-----------------------------------------------------------------------------------
----------------------------------

Issue : BITS052426 - Cables do not detect/show all devices - Equinox

System : R920
Module : Cables
Impact : Factory & Customer
Authors : robib
Test #1 : Cables -conf
Expect : Initial Cables module check in. Tests should Pass.

Issue : Default Touchscreen to SW_MAXIMIZE

System : Notebooks
Module : Touchscreen
Impact : Factory
Authors : robib
Test #1 : Touchscreen -r
Expect : Should display maximized window

Issue : Added USB device ID 0EEF:0001 to the USB INF file.

System : any
Module : DDUsbDriver
Impact : Factory
Authors : carla
Test #1 : ddusbdiag
Expect : Test to load the driver if device with USB ID of 0EEF:0001 is in the
system.

Issue :
Add TBU firmware flash utility
System :
System with TBU
Module :
Disk
Impact :
Factory & customer
Authors :
rdb
Test #1 :
On a system with TBU attached and with firmware files available
run disk -d:tbu -TBUflash -fwDir:<firmware directory> -forceflash
Expect : TBU should be updated with latest firmware
Test #2 : On a system with TBU attached and with firmware files available and
previously flashed
run disk -d:tbu -TBUflash -fwDir:<firmware directory>
Expect : TBU firmware should not be updated
Test #3 : On a system with TBU attached and with firmware files available and
previously flashed
run disk -d:tbu -TBUflash -fwDir:<firmware directory> -backflash
Expect : TBU firmware should be flashed to lower version

Issue : Add hashfile support for System Inventory List

System : All
Module : SystemConfig
Impact : Customer & Factory
Authors : rdb
Test #1 : Run SystemConfig -sil -hashfile:<hashfile> -o:test.txt
Expect : hashfile contents to be in test.xml

Issue : Fixes issue seen with buildverify abd -restort switch

System : All
Module : SystemConfig
Impact : Customer & factory
Authors : rdb
Test #1 : Run SystemConfig -bv -store, then run SystemConfig -bv -restore
Expect : Both tests should pass

Issue : LCD test cannot enter '6' character and cannot abort test.
Change : 4145
System : Servers with front panel LCD
Module : ServerMgmt
Impact : Factory
Authors : rods
Test #1 : Run "servermgmt -fplcdtest" on a system that has an LCD.
Expect : You should be able to enter any character shown on the front panel.

Issue : BITS053843 Add cables support for Shamu to WBDD 6043

System : Shamu, OEM Ready Orca
Module : cables
Impact : Factory & Customer
Authors : haimingw
Test #1 : Run "cable -conf" on a Shamu system
Expect : Verify all cables status are correctly reported

Build 6042.8
-----------------------------------------------------------------------------------
----------------------------------

Issue : BITS052707 ChassisType is Unknown using WBDD 6042 In Tulum

System : Amazon9, AmazonX, Tulum
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and conf results match hardware

Build 6042.5
-----------------------------------------------------------------------------------
----------------------------------

Issue : Drives in RAID config are not showing up in disk -conf output
System : Big Sur, Little Sur, Negril
Impact : Factory and Customer
Authors : rdb
Modules : disk
Test #1 : On a BS, LS or N with RAID setup run disk -conf
Expect : All drives should up under the correct controller

Build 6042.4
-----------------------------------------------------------------------------------
----------------------------------

Issue : mSATA device not showing up as mSATA

System : Audi 15
Impact : Factory and Customer
Authors : rdb
Modules : disk
Test #1 : On an with mSATA installed run disk -conf
Expect : mSATA device should have mSATA field output of YES

Build 6042.3
-----------------------------------------------------------------------------------
----------------------------------

Issue : Multi-media keys for cmdline need to be input with -kh0 (special case)
: (this allows user to select specfic multi-media keys and skip others)
System : Notebooks only
Modules : Keyboard
Impact : Factory & Customer
Authors : robib
Test #1 : keyboard -kh01FF -kh100000000 -kh200000000 -kh300000000 -kh400000000 -
kh500000000 -kh600000000
Expect : Should display multi-media keys only and allow user to press and
recognize scan

Build 6042.2
-----------------------------------------------------------------------------------
----------------------------------
Warning: Older versions of dddriver.sys are not compatible with modules 6042 or
greater. Older versions
of the driver must be uninstalled. This can be done with a system reboot.
-----------------------------------------------------------------------------------
----------------------------------
Issue : BuildVerify failing in SystemConfig and add Dell PN to SIL output for
commodities with PPID
Systems : MacAllen13 and MacAllen 15
Modules : SystemConfig
Impact : Factory & Customer
Authors : rdb
Test #1 : Run SystemConfig -bv -gcf:<valid gcf file>
Expect : System should pass build verification
Test #2 : Run SystemConfig -sil
Expect : DPN filed should show up under Motherboard and HDD sections

Issue : Added AmazonX cables support and fixed ChassisID issue on Amazon9
: (no key to be displayed for specific row)
System : Amazon9, AmazonX
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : no errors and conf results match hardware

Issue : Bullit getting an exception error in SystemConfig

Systems : Bullit
Modules : SystemConfig
Impact : Factory & Customer
Authors : rdb
Test #1 : Run SystemConfig -xml
Expect : SystemConfig to complete without an exception

Issue : Milky Way not recognizing drives correctly

System : Milky Way
Modules : Disk
Impact : Factory & Customer
Authors : rdb
Test #1 : Run disk -f:1 -mon
Expect : All tests pass

Issue : Allow multi-media keys to be recognized with -kh[n] cmdline parameter

System : Notebooks only
Modules : Keyboard
Impact : Factory & Customer
Authors : robib
Test #1 : keyboard -multi -kh100000000 -kh200000000 -kh300000000 -kh400000000 -
kh500000000 -kh600000000
Expect : Should display multi-media keys only and allow user to press and
recognize scan

Issue : Change default for PCIe -util:N arg to 0=dump for Client. Still 1=test
for servers.
System : Client only
Modules : PCIe
Impact : Factory & Customer
Authors : marky
Test #1 : pcie
Expect : Should always pass on client systems (unless -util:1 provided)

Build 6042.1
-----------------------------------------------------------------------------------
----------------------------------
Warning: Older versions of dddriver.sys are not compatible with modules 6042 or
greater. Older versions
of the driver must be uninstalled. This can be done with a system reboot.
-----------------------------------------------------------------------------------
----------------------------------

Issue : Keyboard bitmask for keys in -kh comamnd line can have zero value
: (no key to be displayed for specific row)
System : Notebooks only
Modules : Keyboard
Authors : robib
Test #1 : keyboard -kh100000000 -kh200000000 -kh300000000 -kh400000000 -kh500000000
-kh600000000
Expect : Should display empty layout (no keys for any row)

Issue : Add 3 FBTs for CPG CFI that remove DST Short test
System : All CPG Systems
Modules : Disk
Authors : rdb
Test #1 : On a CPG system run disk -f:4 -mon
Expect : DST Short should not run. All tests should pass.

Issue : BITS042824: Help screen incorrect for layout line

: (this was fixed by changeset 3353 before BITS was opened)
System : Notebooks only
Modules : Keyboard
Authors : robib
Test #1 : Keyboard -l [BR|JP]
Expect : Should display BR and JP Layout

Issue : Add Cables support for PALM_BEACH_AIO

System : PALM_BEACH_AIO
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : Passing result and test results match Motherboard

Issue : BITS029721 WBDD: SSI_OAK: Device test option lost when run 'NbPanel.exe -
Conf' with UEFI only mode
System : All Win8 systems
Impact : Factory & Customer
Authors : bjt
Modules : NA
Test #1 : Run NbPanel.exe -conf
Expect : All devices and tests should be available.
Test #2 : Run all test modules.
Expect : Verify that they work the same as the previous release.

Issue : Add non-interactive support for CD Tray Test

System : All
Impact : Factory & Customer
Authors : rdb
Modules : disk
Test #1 : On a system with Half Height ODD run disk -d:cdrom -f:5 -ix -mon
Expect : All tests should pass without any operator intervention
Test #2 : On a system with slimline ODD run disk -d:cdrom -f:5 -ix -mon
Expect : Operator should bb prompted to close tray. All tests should pass.

Issue : Add Mac Addresses to Baseboard conf output, add Front Facing PCI to
PCIDevices conf output and removed from disk
conf output, added NIC conf output and added System Inventory List
generation
System : All
Impact : Factory & Customer
Authors : rdb
Modules : SystemConfig and Disk
Test #1 : Run SystemConfig -conf
Expect : 1) Baseboard conf will contain LOM MAC address(es), if server will
contain BMC/iDRAC and iSCSI MACS if appropriate.
2) If FFP is installed the FFP will show up under PCIDevices and will not
show up as a BP under disk devices
3) All NICs will show up under NIC conf output
Test #2 : Get a valid GCF file for a system. Run SystemConfig -gcf:<gcffile> -sil -
o:test.txt -xml
Expect : System Inventory Log will be output to test_SIL.xml

Issue : Modify 0x413C to be blocks of 16 devices from 0x8160 to 0x81BF

System : All
Impact : Factory
Authors : carl
Modules : USBDriver
Test #1 : DDUsbDiag -conf
Expect : Driver to load for any UBIST enabled device that is also in the INF file.

Issue : Adjust the logic for validation in DDDriver.sys to work properly on iSOC
systems.
System : Penfolds
Impact : Factory
Authors : carl
Modules : DDDriver
Test #1 : cables -conf
Expect : Driver to load properly without run-time warnings if executed on an iSOC
based system.
Issue : DIMM rank not being output, LRDIMM output for Memory Detail bit 15
System : All
Impact : Factory
Authors : bbw
Modules : Memory
Test #1 : Memory -conf
Expect : Confirm Rank field is output, else BIOS failed to fill in SMBIOS. Submit
defect on BIOS.

Issue : Add USB ID's : 1BCF:280B, 1748:143F

System : If camera with this ID is used
Impact : Factory
Authors : carl
Modules : USBBist driver
Test #1 : ddusbdiag
Expect : Test to find and install the driver for these camera modules

Issue : BITS043027 - Add back PSU cable test for INDY (reverses DF552116)
System : Indy
Impact : Factory and Customer
Authors : robib
Modules : cables
Test #1 : Setup Indy with two PSU's
Expect : cables -conf should show both installed

Issue : Fix bug with setting global flag with -kh[n](XXXX) parameter
System : Portables
Impact : Factory and Customer
Authors : robib
Modules : keyboard
Test #1 : keyboard -v -kh19800 -kh2000801 -kh3003208 -kh40061 -kh501800 -kh60023
Expect : Should not display all keys

Issue : Add PPID to conf output for SAS drives

System : All systems with SAS drives
Impact : Factory and Customer
Authors : rdb
Modules : disk
Test #1 : On a system with SAS drives run disk -conf
Expect : PPID to show up in conf output

Issue : Add PCIESSD type to Disk -ficore output

System : 12G Servers w/PCIeSSD
Impact : Factory and Customer
Authors : rdb
Modules : disk
Test #1 : On a 12G server with PCIe SSD drives run disk -ficore
Expect : PCIESSD to show up in output

Issue : Fixes Backplane Firmware format

System : Servers with Backplanes
Impact : Factory & Customer
Authors : rdb
Modules : disk
Test #1 : On a server with a BP run disk -conf
Expect : BP FwRev should be formatted in x.yz where y is 0 if z is f or less

Issue : BITS046297: TEXT_GUI for Console Redirection is crude. Also need PPID for
MB's and HDD's
System : All
Modules : Cables
Authors : marky
Test #1 : cables -conf
Expect : Verify the PPID of the motherboard is displayed.

Issue : Add new VID:PID definitons for USB cameras that are part of the Win8
compliant platforms.
Issue : Added USB Camera ID for VID 0408
System : All
Impact : Factory
Authors : carl
Modules : USBDriver
Test #1 : DDUSBDiag
Expect : Verify no errors finding and loading the driver for the devices listed in
the INF file.

Issue : BITS040487 Add backplane signal and power detection for Ghostrider
System : Ghostrider
Impact : Factory and Customer
Authors : hw
Modules : cables
Test #1 : On a Ghostrider server run cables.exe -conf
Expect : Make sure that backplane signal and power status is correctly reported

Issue : BITS026908 Change Disk.exe to make sure to run in parallel with

memory.exe reliably
System : All
Impact : Factory and Customer
Authors : bbw
Modules : memory
Test #1 : Run disk non-DST test with memory using "-parallel" on memory command
line.
Expect : Both tests should run to completion without error due to memory
allocation failure.

Issue : BITS042451 Add Serial Port Internal loop back test for Win Based DellDiag

System : All
Impact : Factory
Authors : hwang
Modules : serial
Test #1 : run serial.exe test on a server with serial port
Expect : It should run modem control, line control, transmission test on verious
baudrates.

Issue : Alter servermgmt front panel LCD characters used to verify operation from
a,h,2,8 to a,h,2,6.
System : 12G servers with front panel LCD
Impact : Factory
Authors : fritzk
Modules : servermgmt
Test #1 : run servermgmt -fplcdtest -i
Expect : the list of characters that are used to verify the LCD are a, h, 2, 6;
not 8.

Build 6041.4
-----------------------------------------------------------------------------------
----------------------------------
Issue : Bring USB Driver INF files up to latest version
Issue : Modify 0x413C to be blocks of 16 devices from 0x8160 to 0x81BF
System : All
Impact : Factory
Authors : carl
Modules : USBDriver
Test #1 : DDUsbDiag -conf
Expect : Driver to load for any UBIST enabled device that is also in the INF file.

Build 6041.3
-----------------------------------------------------------------------------------
----------------------------------

Issue : Fix bug with setting global flag with -kh[n](XXXX) parameter
System : Portables
Impact : Factory and Customer
Authors : robib
Modules : keyboard
Test #1 : keyboard -v -kh19800 -kh2000801 -kh3003208 -kh40061 -kh501800 -kh60023
Expect : Should not display all keys

Build 6041
-----------------------------------------------------------------------------------
----------------------------------

Issue : Adds mSATA support for Carrera and fixes Mercedes 14/15 mSATA table
entries
System : Carrera, Mercedes 14/15
Impact : Factory & Customer
Authors : rdb
Modules : disk
Test #1 : On a Mercedes 14/15 and Carrera with mSATA device run disk -conf
Expect : mSATA device conf outout mSATA field should have a value of YES

Issue : E2E Keyboard test requires user selection of Keys from command line
: User selection from command line does not allow multi-media or custom
keys but
: pressing such a key shows a change in scan count and can cause error in
keyboard sequence test
System : Portables
Impact : Factory
Authors : robib
Modules : Keyboard
Test #1 : keyboard -tkbd_sequence -k83 -kh11FFF -kh21FFFF -kh31FFFF -kh41FFF -
kh51FFF -kh67FF
Expect : Standard US Keyboard Layout should be displayed and pressing multi-media
or custom
: key should not change scan count in low right hand corner of screen

Issue : E2E Keyboard test requires user selection of Keys from command line
: User selection from command line does not allow multi-media or custom
keys but
: pressing such a key shows a change in scan count and can cause error in
keyboard sequence test
System : Portables
Impact : Factory
Authors : robib
Modules : Keyboard
Test #1 : keyboard -tkbd_sequence -k83 -kh11FFF -kh21FFFF -kh31FFFF -kh41FFF -
kh51FFF -kh67FF
Expect : Standard US Keyboard Layout should be displayed and pressing multi-media
or custom
: key should not change scan count in low right hand corner of screen

Issue : E2E Keyboard test requires user selection of Keys from command line
: CR553855: E2E KeyBoard test coverage to reduce QT time in Client
platforms
System : Portables
Impact : Factory
Authors : robib
Modules : Keyboard
Test #1 : Keyboard.exe -kh17FFF -kh20FFFFF -kh30FFFFF -kh47FFF -kh50FFFF -kh60FFF
Expect : On US Keyboard Layout rightmost key on each row is skipped (not
displayed)
Test #2 : Keyboard.exe -kh1FFFE -kh21FFFFE -kh31FFFFE -kh4FFFE -kh51FFFE -kh61FFE
Expect : On US Keyboard Layout leftmost key on each row is skipped (not displayed)
Test #3 : Keyboard.exe -kh1DDDD -kh21FFFFF -kh31FFFFF -kh4FFFF -kh51FFFF -kh61FFF
Expect : On US Keyboard Layout first row modified to skip F1, F5, F9 and PrtScr
: All other rows show all keys

Issue : Add in aux_led and intruder_cable GPIO for new MotherBoard rev 010
System : BSLSN
Impact : Customer(4216.3) & Factory
Authors : robib
Modules : cables
Test #1 : On a system with new MB verify the above cable entries are displayed
Expect : Validate cables test pass

Issue : Display HDD ePPID in disk -conf output

System : All systems that have SATA drives
Impact : Customer & Factory
Authors : rdb
Modules : disk
Test #1 : On a system with a SATA drive installed run disk -conf
Expect : PPID tag should be displayed in output

Issue : HDDUSB test failing read

System : Oak
Impact : Customer & Factory
Authors : rdb
Modules : disk
Test #1 : With a USB key installed run disk -d:HDDUSB -f:1 -mon
Expect : all test pass

Issue : Add support for Manufacturer Access information

System : All notebooks
Impact : Factory
Authors : vm
Modules : battery
Test #1 : Run "battery -conf" to see the "Manufacturer Access" information
Expect : all test pass

Issue : Add support for battery temperature returned in kelvin or centigrade

System : All notebooks
Impact : Customer & Factory
Authors : vm
Modules : battery
Test #1 : Run "battery -conf" to see temperature information. This should be
reflected correctly in centrigrade
Expect : all test pass

Build 6040.9
-----------------------------------------------------------------------------------
----------------------------------

Issue : RD1000 not showing up in Disk -conf

System : Ghost Rider
Impact : Factory & Customer
Author : rdb
Modules : Disk
Test #1 : On a system with RD1000 run disk -conf
Expect : RD1000 should show up in conf output

Build 6040.8
-----------------------------------------------------------------------------------
----------------------------------

Issue : Add USB ID's : 1BCF:280B, 1748:143F

System : If camera with this ID is used
Impact : Factory
Authors : carl
Modules : USBBist driver
Test #1 : ddusbdiag
Expect : Test to find and install the driver for these camera modules

Build 6040
-----------------------------------------------------------------------------------
----------------------------------

Issue : 6GB SAS Expander showing up as Hard Drive

System : GhostRider
Impact : Customer and Factory
Authors : rdb
Modules : disk
Test #1 : On a GR with 6GB Exoander installed run disk -conf
Expect : Expander should show up as EXCn with commodity type of expander

Issue : Max x16 negotiated x8 training error

System : Audi A4 AMD
Impact : Customer & Factory
Authors : mikel
Modules : PCIe
Test #1 : run PCIE
Expect : verify there are no errors

Issue : Verify Test failing and locking up drive

System : Big Sur
Impact : Customer & Factory
Authors : robib, rdb
Modules : disk
Test #1 : run disk -f:5 -mon
Expect : all test pass

Issue : KVM virtual CD causing Optical Drive test to fail

System : Ghost Rider
Impact : Customer & Factory
Authors : rdb
Modules : disk
Test #1 : On a Ghost Rider connected to KVM run disk -conf
Expect : Virtual CD to be in output

Issue : Invalid XML tag format

System : Big Sur
Impact : Customer & Factory
Authors : rdb
Modules : PCIe
Test #1 : run PCIE -conf -xml -o:pcie
Expect : open pcie.xml in a browser and verify there are no browser errors

Issue : Disk -f:14 failing for GetPartition Information

System : Milky Way
Impact : Customer & factory
Authors : rdb
Modules : disk
Test #1 : run disk -f:14 -mon
Expect : Test should pass

Issue : BITS027863: BITS ?P3 - Front panel audio cable diagnostic failure when
there is add on audio card
System : BSLSN
Modules : Cables
Authors : robib (added also to 6038A1 as branch)
Setup : Add-in audio card with Fp-audio connected to it
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : FP Audio cable test should not fail as test is Optional

Issue : Add Front Facing PCI slot support

System : 12g servers
Impact : Customer & Factory
Authors : rdb
Modules : SystemConfig
Test #1 : On a 12g server with FFP installed and cards in FFP run SystemConfig -
d:Misc
Expect : Cards plugged into FFP should have PCISlot information

Issue : Add LTO-6 TBU support

System : 12G servers
Impact : Customer & factory
Authors : rdb
Modules : disk
Test #1 : On a 12G server with LTO-6 TBU installed run disk -d:tbu -f:1 -mon
Expect : All tests should pass
Test #1 : On a 12G server with LTO-6 TBU installed run disk -d:tbu -f:2 -mon
Expect : All tests should pass

Issue : mSATA slot support

System : All BMWZ4 and BMWZ5 systems
Impact : Customer & factory
Authors : rdb
Modules : disk
Test #1 : On a system with mSATA device installed run disk -conf
Expect : mSATA device should have mSATADevice tag equal to Yes

Issue : PCIe default does not test anything

System : All
Impact : Customer & factory
Authors : marky
Modules : PCIe
Test #1 : pcie
Expect : Verify test passes and displays PCIe information

Issue : Add USB ID's for cameras : 0c45::647A, 064E::812B, 0c45::648b

System : If camera with this ID is used
Impact : Factory
Authors : carl
Modules : USBBist driver
Test #1 : ddusbdiag
Expect : Test to find and install the driver for these camera modules

Issue : Add USB ID's : 1BCF:289B, 413C:819A, 413C:818E, 413C:8196, 413C:819B,

413C:891D, and 0C45:646B
........: 1BCF:2982, 1BCF:2896, 413C:81A2, 413C:81A3, 413C:81A4
System : If camera or WWAN/WLAN with this ID is used
Impact : Factory
Authors : carl
Modules : USBBist driver
Test #1 : ddusbdiag
Expect : Test to find and install the driver for these camera and WWAN/WLAN
modules

Build 6039.9
-----------------------------------------------------------------------------------
----------------------------------

Issue : Added USB Camera ID for VID 0408.

System : All
Impact : Factory
Authors : carl
Modules : USBDriver
Test #1 : DDUSBDiag
Expect : Verify no errors finding and loading the driver for the devices listed in
the INF file.

Build 6039.7
-----------------------------------------------------------------------------------
----------------------------------

Issue : Add new VID:PID definitons for USB cameras that are part of the Win8
compliant platforms.
System : All
Impact : Factory
Authors : carl
Modules : USBDriver
Test #1 : DDUSBDiag
Expect : Verify no errors finding and loading the driver for the devices listed in
the INF file.

Build 6039.6
-----------------------------------------------------------------------------------
----------------------------------

Issue : Add USB ID's : 1BCF:289B, 413C:819A, 413C:818E, 413C:8196, 413C:819B,

413C:891D, and 0C45:646B
........: 1BCF:2982, 1BCF:2896, 413C:81A2, 413C:81A3, 413C:81A4
System : If camera or WWAN/WLAN with this ID is used
Impact : Factory
Authors : carl
Modules : USBBist driver
Test #1 : ddusbdiag
Expect : Test to find and install the driver for these camera and WWAN/WLAN
modules

Build 6039
-----------------------------------------------------------------------------------
----------------------------------

Issue : Same drive showing up in conf multiple times with new Intel driver
System : Milky Way
Impact : Customer and Factory
Authors : rdb
Modules : disk
Test #1 : In Win8 PE run disk -conf
Expect : Correct drive entries in conf output

Issue : Add Bobcat expander support

System : Scooby
Impact : Factory & Customer
Authors : rdb
Modules : disk
Test #1 : On a Scooby with Bobcat expander run disk -conf
Expect : Expander to be displayed in conf output

Issue : Add PCIe support to detect training errors properly

System : All
Impact : Factory & Customer
Authors : marky
Modules : PCIe
Test #1 : pcie -util:1
Expect : Verify no errors occur.
Test #1 : pcie -conf
Expect : Verify PCI Express physical slots are displayed, if any, and are unique.
Same slot may be displayed
: for multifunction devices on the same bus, but not for PCI devices on
different PCI buses. This verification
: is for Enterprise only, as many Client systems seem to have BIOS issues
regarding slot numbers.

Issue : The DDUsbDriver.sys file and associated INF and CAT files must be signed.
: Image used for Win8 PE 64-bit must have the testing with signed drivers
bit enabled in the image.
: All tested devices must be included in the signed INF file now. If the
device is not part of the signed
: driver, then the testing will fail on that device. Submit a change
request in Agile and include the Vendor ID
: and Product ID and short description of the device that failed. Verify
that the test bits are enabled in
: the image and that the device is not already noted in the INF file.
System : All
Impact : Factory
Authors : carl
Modules : ddusbdiag.exe, ddusbdriver.sys
Test #1 : ddusbdiag.exe
Expect : Test to install the driver on the system and test USB BIST enabled
devices. Note that the image
must have the testing with signed drivers bit enabled in the image.
Driver is not verified as
compatible with full Win8 OS implementations, just the Win8 PE image for
factory testing.

Issue : Video -conf does not redraw screen properly in WinPE8, only on first
boot.
System : All
Impact : Factory & Customer
Authors : marky
Modules : video
Test #1 : video -conf {must be a fresh boot to WinPE 8}
Expect : Verify screen and windows redraw properly after it completes

Issue : BITS025791: Miss some check items with delldiag

System : BSLSN
Modules : Cables
Authors : robib (added also to 6038A1 as branch)
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : Passing result and hardware matches MLK Motherboard
Expect : Intrusion detection and Mfgmodejumper add

Build 6038
-----------------------------------------------------------------------------------
----------------------------------

Issue : CR552557: Need WBDD to cover the whole interactive CD test. Removes 1
interaction
System : All
Modules : Disk
Authors : rdb
Test #1 : On a system with tray load ODD run disk -d:cdrom -f:5 -mon
Expect : Tray should eject, message displayed prompting operator to close tray,
test pass
Test #2 : On a system with Half Height ODD run disk -d:cdrom -f:5 -mon
Expect : Tray should eject, message displayed prompting operator to continue, test
pass
Test #3 : On a system with slot load ODD run disk -d:cdrom -f:5 -mon
Expect : test should pass
Test #4 : On a system with tray load ODD run disk -d:cdrom -f:6 -mon
Expect : Tray should eject, message displayed prompting operator to insert test
media and to close tray, test pass
Test #5 : On a system with Half Height ODD run disk -d:cdrom -f:5 -mon
Expect : Tray should eject, message displayed prompting operator to insert test
media, test pass
Test #6 : On a system with slot load ODD run disk -d:cdrom -f:5 -mon
Expect : message displayed prompting operator to insert test media

Issue : Add Cables support for MICHELIN_AIO and PIRELLI_AIO

System : MICHELIN_AIO, PIRELLI_AIO
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : Passing result and hardware matches MLK Motherboard

Issue : DF554003: B/LSN: Error occur when running 'USB Disk' diagnostic test via
WBDD
System : Big Sur, Little Sur and Negril
Impact : Factory & Customer
Authors : rdb
Module : Disk
Test #1 : With a USB memory stick installed run Disk -d:HDDUSB -f:1 -mon
Expect : All tests should pass

Issue : CR552734 : Update the Processor or System Configuration module to return

the production status of the CPU
System : All 12G servers
Impact : Factory
Authors : carl, roger
Module : DDDriver.sys, SystemConfig.exe
Test #1 : SystemConfig
Expect : CPU production status line on systems with the specific CPU installed.

Build 6035
-----------------------------------------------------------------------------------
----------------------------------

Issue : CCC factory Pilot : Palm Beach MLK will now have Option for Intrusion
switch
System : Palm Beach MLK
Impact : Factory
Authors : carl
Module : Cables
Test #1 : Cables.exe
Expect : Intrusion switch to pass all the time, even if the cable is not
connected.
: Switch cable must be verified by factory process if order contains it.

Issue : BITS019389 - WBDD: Memory Test Change Request

System : All
Impact : Factory & Customer
Authors : bbw
Module : Memory
Test #1 : Memory -?
Expect : Should display -f:21 as option
Test #2 : Memory -f:21
Expect : Should run memory test in short (~1 minute) time.

Issue : CR552957: Add TCM Cables signal for McCave (R910)

System : McCave 11G
Impact : Factory & Customer
Authors : robib
Module : Cables
Test #1 : cables -conf
Test #2 : cables -details
Expect : Should show TPMPlugInModule installed in new 11G supported systems
Expect : Should show STMicro installed in old systems

Issue : CR543856: Include tests within video.exe to test for faulty LCD Screen.
System : Notebooks
Impact : Factory only
Authors : jimd
Module : video
Test #1 : video /?
Expect : Show options for LCD screen tests
Test #2 : video -rgb -delay:1
Expect : Instructions with a random prompt displayed; 7 colors displayed for 1
second each
: A random prompt is displayed at the end to verify correctness.
Test #3 : video -rgb -colors:rgb -delay:1
Expect : Instructions with a random prompt displayed; Red, Green and Blue are
displayed for 1 second each.
: A random prompt is displayed at the end to verify correctness.
Test #4 : video -pattern
Expect : Instructions with a random prompt displayed; a TV style test pattern is
displayed for 15 seconds.
: A random prompt is displayed at the end to verify correctness.

Issue : CR553133: Update Fan Types for Memory, PCI and HDD returned by BSLSN EC
System : BSLSN
Impact : Affects factory & Customer debug output only
Authors : robib
Module : Fan
Test #1 : fan -v -o:fandbg.txt
Expect : Debug should show Fan types of 0x5, 0x6, 0x7 in debug output

Issue : Rename TPM status in cables 12G servers to TPM plugin module status
System : 12 G servers
Impact : Factory & Customer
Authors : hw
Test #1 : On Ghostrider system, run "cables.exe"
Expect : TPM status string should be replaced with TPM plugin module status
: NDC is no longer listed as a cable item for Ghostrider

Issue : CR552557: Need WBDD to cover the whole interactive CD test

System : All
Impact : Factory & Customer
Authors : rdb
Test #1 : On a system with tray load ODD run disk -d:cdrom -f:5 -mon
Expect : Tray should eject, message displayed prompting operator to close tray,
test pass
Test #2 : On a system with Half Height ODD run disk -d:cdrom -f:5 -mon
Expect : Tray should eject, message displayed prompting operator to continue, test
pass
Test #3 : On a system with slot load ODD run disk -d:cdrom -f:5 -mon
Expect : test should pass
Test #4 : On a system with tray load ODD run disk -d:cdrom -f:6 -mon
Expect : Tray should eject, message displayed prompting operator to insert test
media and to close tray, test pass
Test #5 : On a system with Half Height ODD run disk -d:cdrom -f:5 -mon
Expect : Tray should eject, message displayed prompting operator to insert test
media, test pass
Test #6 : On a system with slot load ODD run disk -d:cdrom -f:5 -mon
Expect : message displayed prompting operator to insert test media

Issue : CR551219 Add Touchscreen four corner test in Win8 PE stack

System : Princeville & Sparta
Impact : Factory
Authors : robib
Module : TouchScreen
Test #1 : TouchScreen
Test #2 : Touchscreen -w4
Expect : Displays four corner test and 3x3 matrix test on supported systems

Issue : DF552116 Removed PSU1 and PSU2 from INDY (cabled power supply sensors
don't apply)
System : Indy
Impact : Factory & Customer
Authors : robib
Module : Cables
Test #1 : cables -details
Expect : No PSU1 and PSU2 cables signals displayed

Issue : SystemConfig failing with large errorlevel on Spartan

System : Spartan
Impact : Factory & Customer
Authors : rdb
Module : SystemConfig
Test #1 : On a Spartan whose MB does not have a programmed baseboard serial number
run SystemConfig -conf
Expect : Valid conf output should be displayed

Issue : DF552212/CR553093 Remove cables test for PIM module and ndc from V&I
System : V&I
Impact : Factory & Customer
Authors : robib
Module : Cables
Test #1 : cables -details
Note : NDC GPIO bit fixed with CPLD 018.
Expect : ndc and tpmstatus should not be displayed.

Issue : Sequential Write Read Test failing on RAID device

System : Big Sur
Impact : Factory & Customer
Authors : rdb
Module : Disk
Test #1 : On a BIg Sur with RAID 0 on 2 drives run disk -f:14 -mon
Expect : All tests pass

Issue : Eventlog updates for DCSA.

System : All.
Impact : Factory & Customer
Authors : rods
Modules : Fan, Memory, ServerMgmt
Test #1 : Run "eventlog -dump"
Expect : The output now includes the abstract type of the event, log source, and
raw record.

Issue : Remove filter for IPMI fans that won't change speed for the factory
build. Filter will remain in
: place for the customer.
System : All IPMI systems with Dell iDrac.
Impact : Factory & Customer
Authors : rods
Modules : Fan
Test #1 : Run "fan"
Expect : If the fans do not change speed, the test should fail.

Issue : The ODD, HDD and USB Camera signals should be Optional for Lanikai AIO
System : Lanikai AIO
Modules : Cables
Authors : carl, bill
Test #1 : psa in BIOS
Expect : cables test on ePSA will show state, but not error for HDD, ODD and
Camera

Issue : Add additional protection against interface errors for IPMI systems.
Change : 2387
System : All IPMI systems.
Impact : Factory & Customer
Authors : rods
Modules : Fan, Memory, ServerMgmt
Test #1 : Run the tests as normal.
Expect : The changes should eliminate intermittent errors where the test is not
able to retrieve the
: SEL info or a SEL record.

Issue : The ODD, HDD and USB Camera signals should be Optional for Lanikai AIO,
no HDD installed is a Warning
System : Lanikai AIO
Modules : Cables, Disk
Authors : carl, bill
Test #1 : run ePSA
Expect : Configuration Tab will show current state for HDD, ODD and Camera. No
failure messages on these 3 siganls.
Test #2 : run ePSA (with HDD not installed)
Expect : With no HDD installed, HDD Test will show a "not installed warning"

Build 6034
-----------------------------------------------------------------------------------
----------------------------------

Issue : Add PCI Revision to SystemConfig PCIDevice conf

System : Summit
Impact : Factory & Customer
Authors : rdb
Module : SystemConfig
Test #1 : Run SystemConfig -conf
Expect : PCIDevices should have RevisionId tag
Test #2 : Run SystemConfig -conf -d:MISC
Expect : PCIDevices should have RevisionId tag
Test #3 : Run SystemConfig -conf -noexe
Expect : PCIDevices should have RevisionId tag

Issue : DF550039 - BSLSN Video test failing in SLot#2 but passes in Slot#4.
System : Big Sur
Impact : Factory & Customer
Authors : robib
Module : video
Test #1 : Put video card in slot #1 and run video
Expect : All tests pass

Issue : The USB diag driver was not loading on all UBIST devices in WinPe8.
: Warning: Note that the USB diag no longer supports XP.
System : All
Impact : Factory & Customer
Authors : bjt
Module : ddusbdiag.exe & ddusbdriver.sys
Test #1 : Run the diag on all WinPe versions Vista and greater.
Expect : All tests should pass

Issue : DF550055: B/LSN: Error occur when running 'USB Disk' diagnostic test via
WBDD
System : Big Sur
Impact : Factory & Customer
Authors : rdb
Module : disk
Test #1 : On a system with USB key installed run disk -d:HDDUSB -f:1 -mon
Expect : All tests should pass

Issue : Video test failing for unsupported graphics mode in Win8 PE

System : All
Impact : Factory & Customer
Authors : rdb
Module : Video
Test #1 : Run video
Expect : Test should pass

Issue : On media load failure cdread does not fail but continues to media eject
test
System : All
Impact : Factory & Customer
Authors : rdb
Module : Disk
Test #1 : Run disk -d:cdrom -f:3. Do not insert media when prompted but close tray
and answer "ok"
Expect : Test should fail after cdread.
Test #2 : Run disk -d:cdrom -f:3. Insert media when prompted and press "ok"
Expect : All tests should pass.

Issue : CR518136: IPMI Call to 8 Slot Backplane Returns 4 Slots

System : Ghostrider
Impact : Factory & Customer
Authors : rdb
Module : Disk
Test #1 : On a Ghostrider that has iDrac FW 1.30.30 or later and has 8 Slot BP
connected to motherboard SATA run disk -conf
Expect : 8 slots to be displayed in BP conf output, else 4 slots will be
displayed.

Build 6033
-----------------------------------------------------------------------------------
----------------------------------

Issue : Thread count greater than 64 causes exception error

System : 12G servers
Impact : Factory
Authors : rdb
Module : Disk
Test #1 : On a system with more that 32 devices discovered with disk -conf, run
disk -f:7 -mon
Expect : All tests should pass

Issue : WD DEFT drives failing Mode Page update during Verify test
System : Ghostrider
Impact : Factory
Authors : rdb
Module : Disk
Test #1 : On a Ghostrider with Western Digital WD9001BKHG with FW ver D1S2 run disk
-f:1 -mon
Expect : All tests should pass
Issue : Add RIPS command to ipmi lib to output SD Card Slot for SUMMIT and ORCA
in Disk conf
System : SUMMIT and ORCA
Impact : Factory & Customer
Authors : rdb
Module : Disk
Test #1 : On a SUMMIT or ORCA with SD Card installed run disk -conf
Expect : Slot number for SD Card to be displayed and correct.

Issue : CR543194.3: [ALL] Support Temperature Sensor String method if buffer is

not initialized value
System : All
Impact : Factory & Customer
Authors : billb
Test #1 : Run SysMan.exe
Expect : List of temperature sensors should be the same as the ePSA System Health
Tab list

Issue : Null driver name causing abend for Kamino with Win8PE
System : Kamino
Module : Disk
Impact : Customer & factory
Authors : rdb
Test #1 : Using Win8PE run disk -conf
Expect : Complete conf output

Issue : Set type to RAID for RAID volumes that do not have default entries
System : All with Intel RAID controllers
Module : Disk
Impact : Customer & Factory
Authors : rdb
Test #1 : On a system with Intel RAID set up with Volume name not the default run
disk -conf
Expect : RAID volume should show up under RAID controller as Device Type of RAID

Feature : Added support for a new field in the UBIST descriptor "bDeviceXMLConfig".
This field allows the vendor
: to expose USB device configuration information needed for the Dell
factory.
System : All
Modules : DDUsbDiag
Impact : Factory & Customer
Authors : bjt
Test #1 : No USB devices currently support this new field so just run the tests in
DDUsbDiag.exe.
Expect : All tests should pass.

Issue : Bullit not showing Backplane for no HDD system

System : Bullit
Modules : Disk
Impact : Factory & Customer
Authors : rdb
Test #1 : On a Bullit with no HDD and no controller run disk -conf
Expect : Backplane should show up in output as the correct type.

Issue : 1.8" SSD failing read SMART log page 6 on HiFi

System : HiFi
Modules : Disk
Impact : Factory & Customer
Authors : rdb
Test #1 : On a Hifi with 1.8" SSD run disk -f:1 -mon
Expect : All test should pass

Issue : Added PciSlot tag to PCIDevice in SystemConfig conf

System : All
Modules : SystemConfig
Impact : Factory & Customer
Authors : rdb
Test #1 : On a system that has an add-in PCI card run SystemConfig -conf
Expect : PciSlot tag under add-in PCIDevice will have coorect PCI Slot number
Test #2 : On a system that has an add-in PCI card run SystemConfig -conf -d:MISC
Expect : PciSlot tag under add-in PCIDevice will have coorect PCI Slot number
Test #3 : On a system that has an add-in PCI card run SystemConfig -conf -noexe
Expect : PciSlot tag under add-in PCIDevice will have coorect PCI Slot number

Issue : Update sensor to add mnemonic for IPMI sensors.

System : All
Impact : Factory & Customer
Authors : rs
Test #1 : Run SysMan.exe
Expect : Correct values should be reported.

Build 6032
-----------------------------------------------------------------------------------
----------------------------------

Issue : DF545415: Defy: iDRAC reports single PSU as dual PSU

System : Slice, Silk, Defy
Modules : cables
Impact : Factory & customer
Authors : fritzk
Test : Test cables on SDS with PSU. PSU2 should show as Uninstalled.

Issue : DF539347 SDS cables new riser decode.

System : Slice, Silk, Defy
Modules : cables
Impact : Factory & customer
Authors : fritzk
Test : Test cables using bouth 1CPU and 2CPU for each system type, 6 tests.
Expect : the riser types should be a,c,d,e,f no non-valid allowed.

Issue : Add PRINCEVILLE Port 1 to the mSATAArray in mSATA.h

System : PRINCEVILLE
Modules : Disk
Impact : Factory & Customer
Authors : billb
Test #1 : With mSATA device installed run disk -conf
Expect : mSATADevice field to be displayed with value of Yes

Issue : DF543186 [Madone] LRDIMM info in memory -conf. This should be a change
request since we are adding a
: feature to provide something not yet available in smbios.
System : All 12G servers
Impact : Factory
Authors : rs
Test #1 : Run "memory -conf -xml"
Expect : On 12G servers where the interface exists, the output will contain an
<SPD> tag with all the dimm SPD
 : in a single stream formatted as 2 hex bytes with no separator. This is a
factory only feature and
: will not appear in customer output.

Issue : Add Expander to Disk -conf output

System : Vince
Impact : Factory & Customer
Authors : rdb
Test : On a Vince with Expander connected to PERC run disk -conf
Expect : Expander to be under PERC

Issue : DST failing for SMART command failure on sATA drive

System : Big Sur
Impact : Customer & Factory
Authors : rdb & robib
Test #1 : On a Big Sur with SATA drives run disk -f:7 -mon
Expect : Test should not fail for SMART failure.

Issue : Disk -ficore does not have output for PERC

System : Vince
Impact : Customer & Factory
Authors : rdb & robib
Test #1 : On a Vince with drives connected to PERC run Disk -FiCore
Expect : FiCore information to be displayed

Issue : Added sensor mnemonic field, exposed only in the DCSA utility.
System : All
Impact : Factory & Customer
Authors : bjt
Test #1 : Run Battery.exe and SysMan.exe.
Expect : Modules should behave the same as previous releases.

Issue : Added battery temperature, voltage, current, remaining capacity, relative

state of charge, relative charge,
: manufacture date, serial # fields to the battery configuration output.
System : Notebooks
Impact : Factory & Customer
Authors : bjt
Test #1 : Battery -conf
Expect : Correct values should be reported.

Issue : All PCI Devices not being discovered by PCI HW discovery

System : All
Impact : Factory & Customer
Authors : rdb & marky
Test #1 : Run SystemConfig -d:MISC
Expect : All PCI devices should have a valid tag

Issue : Big Sur failing disk -f:14

System : Big Sur
Impact : Factory
Authors : rdb
Test #1 : Run disk -f:14 -mon
Expect : Test should pass

Issue : Add -FiCore switch to disk

System : All
Impact : Factory
Authors : rdb
Test #1 : Run disk -FiCore
Expect : PhysicalDrive information to be displayed

Issue : Add Driver tag to disk -conf INTELRAID controller output

System : IntelRAID systems
Impact : Factory & Customer
Authors : rdb
Test #1 : On a system with Intel controller in AHCI or RAID mode run disk -conf
Expect : Driver tag will be displayed in IntelRAID device section

Issue : DF542746:PCI Info in SystemConfig output for PCIe Bridge Adapter Card
System : 12G Servers
Modules : SystemConfig
Impact : Factory & Customer
Authors : rdb
Test #1 : On a 12G server with PCIe SSD run SystemConfig -conf -d:MISC
Expect : PCIe Bridge Adapter Card should not have SubVendorID and SubDeviceID as
0000 0000
Test #2 : On a 12G server with PCIe SSD run SystemConfig -conf -noexe
Expect : PCIe Bridge Adapter Card should not have SubVendorID and SubDeviceID as
0000 0000
Test #3 : On a 12G server with PCIe SSD run SystemConfig -conf
Expect : PCIe Bridge Adapter Card should not have SubVendorID and SubDeviceID as
0000 0000

Issue : Add port mapping table for motherboard slot conf output
System : MISSION HILLS MLK,MISSION HILLS,SAWGRASS MLK,SAWGRASS,CYPRESS
POINT,PEBBLE BEACH,PALM BEACH,ANDROMEDA
Modules : Disk
Impact : Factory & Customer
Authors : rdb
Test #1 : On the systems above, with ODD connected to SATA2 or SATA3, run disk -
conf
Expect : MotherBoardSlot filed for ODD should contain correct connector number

Issue : Add MSATA field to disk conf output

System :
CYPRESS_POINT,PEBBLE_BEACH,BROOKS_15,BROOKS_17,REEBOK,AUDI_A3,AUDI_A4_UMA,AUDI_A4_G
FX,
:
AUDI_A4_DGFX,AUDI_A7_CR_GFX,AUDI_A7_DGFX,AUDI_A7_GFX,AUDI_A7_UMA,MERCEDES_GLK_GFX,
: MERCEDES_GLK_UMA,MERCEDES_SLK
Modules : Disk
Impact : Factory & Customer
Authors : rdb
Test #1 : On a system that has an mSATA device installed run disk -conf
Expect : mSATADevice field to be displayed with value of Yes
Test #2 : On the same system, remove the mSATA device and run disk -conf
Expect : mSATADevice field to be displayed with value of No

Build 6031
-----------------------------------------------------------------------------------
----------------------------------

Issue : MotherBoardSlot field not displaying with Patsburg chipset.

Systems : 12G servers, Milky Way
Modules : Disk
Impact : Factory & Customer
Authors : rdb
Test #1 : On a 12G server in AHCI mode or Milky Way in RAID mode run disk -conf
Expect : MotherBoardSlot info should be displayed for devices connected to Intel
controller

Issue : Multiple BPs in Disk -conf output for 11G servers

Systems : 11G servers
Modules : Disk
Impact : Factory & Customer
Authors : rdb
Test #1 : On an 11G server that has a BP run disk -conf.
Expect : Only one BP should be displayed

Issue : HiFi embedded controller not displaying as internal controller

System : HiFi
Modules : Disk
Impact : Factory & Customer
Authors : rdb
Test #1 : run disk -conf.
Expect : Controller ControllerInOrExt field should be displayed as Internal

Issue : CR539265: Display CPLD firmware revisions for 12G blades

System : 12G blades
Modules : SystemCOnfig
Authors : bbw
Test #1 : Run systemconfig.exe -conf on 12 blades
Expect : various CPLD version should print, based on blade model

Issue : DF530363: Mezz card C slot can't correct show in ePSA configuration
System : Hi-Fi
Impact : Factory & Customer
Modules : Cables
Authors : bbw
Test #1 : Run cables -conf on Hi-Fi system
Expect : Output should contain SledSlot for the slot that the blade is installed
in.

Issue : CR538422 - add Custom Keys fo Avenger MLK.

System : Avenger MKK
Modules : Keyboard
Authors : robib
Test #1 : Run Keyboard.exe on Avenger/Avenger MLK
Expect : Macro custom keys should be displayed in keyboard test.

Issue : CR534769 Integrate an event log scan into the Fan module (IPMI only).
System : Servers
Modules : fan
Authors : rods
Test #1 : Run 'fan'.
Expect : The module will attempt to change the fan RPMs first. After that, it will
scan the event log for any fan
: events and fail if any Fail or Critical events are found. The module can
now also work on some systems
: that do not have the Dell-specific IPMI commands that are needed to
change the fan speeds.
Test #2 : Create some fake events.
: Copy the following lines to a temporary file "temp.txt" (shift left to
start in col 1):
 : #!Evlog x.x raw data file, SysID=0x0, Vendor=dell, Type=ipmi, Ver=0x20
: #
: # Fake fan failure for Dell BMC
: #
: # Record |Generator|Evm | Sensor | Event

: # ID Type Timestamp | ID |Rev |Type Num |Type Dat1

Dat2 Dat3
: #-------- ---- -------------------|---------|----|---- ----|---- ----
---- ----
: 0x00 0x00 0x02 0xC0 0x9B 0xB6 0x3F 0x20 0x00 0x03 0x04 0x30 0x01 0x54
0x00 0x00 #Fan 0
: 0x00 0x00 0x02 0xC0 0x9B 0xB6 0x3F 0x20 0x00 0x03 0x04 0x31 0x01 0x54
0x00 0x00 #Fan 1
: 0x00 0x00 0x02 0x00 0x00 0x00 0x00 0xB1 0x00 0x04 0x0C 0x01 0x6F 0xA0
0xF0 0x01 #ECC Dimm_1
:
: Run "eventlog -selfile:temp.txt -write".
: Run 'fan' again.
Expect : After the fans are tested, the output should also contain the fan events
from the log.
Cleanup : Run "eventlog -clear:ipmi" to get rid of the events.

Issue : CR539068 Update TopHat IPMI processing.

System : TopHat
Modules : EventLog, ServerMgmt, Memory
Authors : rods
Test #1 : Run 'eventlog -dump'.
Expect : If the log contains any OEM events such as memory ECC, they should be
formatted the same as iDrac.
Test #2 : Run 'memory -f:1'.
Expect : Memory test should run as normal.
Test #3 : Run 'servermgmt'.
Expect : Tests should run as normal. One of the messages should say
"Investigating System Health LED.".

Build 6030
-----------------------------------------------------------------------------------
----------------------------------

Issue : Use PCIe SSD backplane as a condition to add PCIe SSD support
System : 12G servers
Modules : Disk
Impact : Factory & Customer
Authors : rdb
Test #1 : On a 12G server with PCIe SSD cage, remove all PCIe SSD drives and run
"disk -conf"
Expect : PCIe SSD bridge card to be in conf output with PCIe SSD back plane under
it.

Issue : Updated Cables support

: Lanikai AIO - Added Powerswitch detection, changed cable name
fPowerSwitch --> sidekeycable
: Princeville - Added HDMI cable, removed HDMI cable and removed LVDScable
: Olympic - changed cable name fpcable --> sidekeycable
: Eagleton - Added PAID detection of TV Tuner card
: Added MfgModeJumper:
: Eagleton, Olympic, Princeville, Cypress Point, Pebble Beach, Pine
Valley, Sunrise, Milky Way, Andromeda
System : Eagleton, Olympic, Princeville, Lanikai AIO,
: Cypress Point/Pebble Beach, Pine Valley/Sunrise, Milky Way, Andromeda
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : Passing result and hardware matches MLK Motherboard

Issue : Add Cables support for Eagleton

System : Eagleton
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : Passing result and hardware matches MLK Motherboard

Issue : Updated Cables support to match ST Hardware

System : Olympic, PrinceVille, Cypress Point, Pebble Beach, Lanakai AIO, 7 & 9
(MT, DT, SFF)
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : Passing result and hardware matches MLK Motherboard

Issue : SystemConfig -conf output for PCI Devices does not have correct value for
AddInDevice field
System : Zooks
Impact : Factory & Customer
Authors : rdb
Test #1 : On a Zooks with Broadcom 10Gb NIC dev run "SystemConfig -d:Misc"
Expect : AddinDevice field value should be "Yes"
Test #2 : On a Zooks with Broadcom 10Gb NIC dev run "SystemConfig -noexe -d:Misc"
Expect : AddinDevice field value should be "Yes"

Issue : DF538726: SystemConfig.exe -conf output missing PCI Device info for
Broadcom 10Gb NIC dev
System : Zooks
Impact : Factory & Customer
Modules : SystemConfig
Authors : rdb
Test #1 : On a Zooks with Broadcom 10Gb NIC dev run "SystemConfig -d:Misc"
Expect : Output should contain the correct PCI ID for the NIC dev
Test #2 : On a Zooks with Broadcom 10Gb NIC dev run "SystemConfig -noexe -d:Misc"
Expect : Output should contain the correct PCI ID for the NIC dev

Issue : BTO537849 systemconfig -d:BASEBOARD and wmic returing wrong results on

some families
System : GoldCoast, Katisiki, PalmBeach, Tambor, MissionHills, Sawgrass
Impact : Factory & Customer
Modules : SystemConfig
Authors : rdb
Test #1 : Run SystemConfig -conf -d:baseboard
Expect : PPID to be valid or have the message "Invalid PPID - PWA P/N : <what is
found in SMBIOS or <empty>> PWA S/N : <what is found in SMBIOS or <empty>>"

Issue : Skipper MotherBoardSlot for portE showing as 0

System : Skipper
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On a skipper with ODD connected to PortE run disk -conf
Expect : MotherBoardSlot for ODD should be 4

Issue : DF533963: Pressing Alt-GR in UK/BR keyboards highlights L-Ctrl also

System : All systems
Modules : Keyboard
Authors : robib
Test #1 : Run keyboard -luk or keyboard -lbr or keyboard -ljp
Expect : Pressing R-Alt or Alt-Gr should highlight only the key pressed

Issue : DF530020: Non-supported "USB Mini Card" presents in ePSA w/ USFF

System : Lanikai 7 & 9 USFF
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : No support for USFF PCIE-Minicard\

Issue: : DF535382: Skipper Failing DVD Verification

Systems : Skipper
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : Run disk -conf.
Expect : Optical device should have MotherBoardSlot tag.

Issue : Big Sur not displaying PhysicalDrive tag

Systems : Big Sur
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On a Big Sur with no RAID run disk -conf
Expect : PhysicalDrive tag to be displayed for each HDD device.

Build 6029
-----------------------------------------------------------------------------------
----------------------------------

Issue : DF542974: S300 + WD SAS HDD failure in ET

System : Diamas, Coaster
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On a Diamas or Coaster with S300 and WD 900GB SAS Dell P/N 4X1DR run disk
-f:1 -mon
Expect : All tests should pass

Issue : DF540772: Ghostrider Pilot - PCIe cage showing empty

System : Ghost Rider
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On a Ghost Rider with PCIe SSD cage remove all drives and run disk -conf
Expect : PCIe BP should show correct information

Issue : Cypress Point and Pebble Beach mother board slot incorrect
System : Cypress Point and Pebble Beach
Modules : Disk
Author : rdb
Test #1 : On a Pebble Beach with HDD connected to sata0 and sata3 run disk -conf
Expect : MotherBoardSlot assignments should be correct
Issue : DF527774: WBDD memory test failes on full memory config
System : Bullit
Modules : memory
Authors : bbw
Test #1 : Run memory -f: on large (>64Gb memory, 64 processors) system using
WinPE64
Expect : test runs to completion

Issue : DF527551: clearNVRAMjumper in 12G is default "not installed"

System : Vince, Indy
Modules : Cables
Authors : robib
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : clearNVRAMjumper should pass if uninstalled

Issue : CR527783: USC ePSA -R317805 reffers to the IDSDM device as a RIPS
System : Orca, Orca-XD, Madone, Ghostrider, Vince, Indy, Silk, Slice, Defy
Modules : Cables
Authors : haimingw
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : Original RIPS item should be changed to IDSDM

Issue : Add Cables support for Mission Hills MLK and Sawgrass MLK
System : Mission Hills MLK and Sawgrass MLK
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : Passing result and hardware matches MLK Motherboard

Issue : Retrieve sATA HDD form factor from Identify Device command output
System : All
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : Run Disk -conf on a system with sATA drives
Expect : If drive supports form factor then form factor should show up in conf
output

Issue : Memory Leak during sequential seek test

System : Systems with Patsburg chip set
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : Start taskmgr. Run Disk -f:3 -mon. Watch memory usage in taskmgr to
verify that once sequential
seek test starts memory usage does not steadily increase.
Expect : All tests should pass and memory usage should not staedilt increase
during sequential seek tests.

Issue : Changed USB1, USB2 and Front Panel Audio from Optional to Required on
Pine Valley and Sunrise at ODM request
Systems : Pine Valley, Sunrise
Impact : Factory, Customer
Modules : Cables
Authors : carl
Test #1 : Run cables test
Expect : Test passes if all 3 are installed. Tests fails if any one of the 3 are
not installed.
Build 6028
-----------------------------------------------------------------------------------
----------------------------------

Issue : Replace Sequential read tests with 60 minutes of DST Long in Level 3
tests (-f:3 and -f:6)
Systems : All
Impact : Factory & Customer
Authors : rdb
Test #1 : Run disk -f:3 -mon
Expect : All tests pass
Test #2 : Run disk -f:6 -mon
Expect : All tests pass

Issue : Disk -f:3 causes BSOD on GhostRider and hangs on other systems with HDDs
in ATA mode
Systems : All
Impact : Factory & Customer
Authors : rdb
Test #1 : On a system with HDDs connected to MB in ATA mode run disk -f:3 -mon
Expect : All tests pass

Issue : ZeroDisk utility does not work for systems with Intel RAID or AMD RAID
Systems : Systems with Intel RAID and systems with AMD RAID
Impact : Factory
Authors : rdb
Test #1 : On a system with Intel RAID and with RAID set up run disk -ZeroDrive -mon
-ix.
IMPORTANT!!! THIS TEST WILL ZERO ALL DRIVES IN THE SYSTEM!!
Expect : All drives will be zeroed and test passes.
Test #2 : On a system with AMD RAID and with RAID set up run disk -ZeroDrive -mon -
ix.
IMPORTANT!!! THIS TEST WILL ZERO ALL DRIVES IN THE SYSTEM!!
Expect : All drives will be zeroed and test passes.

Issue : Dual optical devices only test one device

Systems : All systems that have dual optical devices
Impact : Factory & Customer
Authors : rdb
Test #1 : On a system with dual optical devices run disk -d:cdrom -f:2 -mon
Expect : All tests pass.

Issue : Remove driver version checking for SWRAID

Systems : All systems that have S100/S110 SWRAID
Impact : Factory & Customer
Authors : rdb
Test #1 : On a system with S100/S110 SWRAID run disk -f:1 -mon
Expect : All tests pass

Issue : Add PhysicalDrive tag to disk -conf output

Systems : All
Impact : Factory
Authors : rdb
Test #1 : Run disk -conf
Expect : PhysicalDrive tag should be in conf output

Issue : Cypress Point and Pebble Beach slot numbers do not match expected slots
Systems : Cypress Point and Pebble Beach
Impact : Factory and Customer
Modules : Disk
Authors : rdb
Test #1 : On a Pebble Beach and Cypress Point with drivers in all slots including
mSATA run disk -conf
Expect : Drives should match up to mother board slots 0 - 3 and mSATA should show
as mb slot 4.

Issue : Added bs and bc switches to ZeroDisk utility

System : All
Impact : Factory only
Modules : Disk
Authors : rdb
Test #1 : On a system that you do not care if the drives get zeroed out run "disk -
ZeroDisk -bs:1000 -bc:1000 -mon"
Expect : System should pass

Issue : DF519801: Fail to detect PCH heatsink with WBDD A6026A0

System : Katsiki, Tambor, Gold Coast
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : Passing result and hardware matches Motherboard Rev0 - Heatsink is
present
Test #2 : Run Cables, Cables -conf, Cables -details
Expect : Passing result and hardware matches Motherboard Rev0 - Heatsink is not
present

Issue : CR520179 Changes Cables.exe to display correct Backplane connections

System : Orca, Orca-XD and Madone
Module : cable.exe
Author : haimingw
Test #1 : On Orca, Orca-XD or Madone system run cable.exe -conf
Expect : Backplane information should be listed starting from BP0 instead of BP1

Issue : Added invalid device on command line check to disk

System : All
Module : Disk
Author : rdb
Test #1 : On any system specify a valid device type and instance and a valid device
type with
an invalid instance,i.e disk -f:1 -d:hdd:0 -d:hdd:100
Expect : Test should fail with Invalid Device messahe

Issue : Orca XD conf output for Backplane does not have connector information
System : Orca XD
Module : Disk
Author : rdb
Test #1 : On an Orca XD run disk -conf
Expect : BP information should have number of slots x drive size.

Issue : Updated Pine Valley and Sunrise ChassisID support

System : Pine Valley, Sunrise
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : Passing result and hardware matches Pine Valley or Sunrise configuration

Build 6027
-----------------------------------------------------------------------------------
----------------------------------

Issue : SCSI Buffer failing for Pliant SSD

System : Zooks
Module : Disk
Author : rdb
Test #1 : On a system with Pliant SSD run disk -f:1 -mon
Expect : All tests pass

Issue : SystemConfig build verification failing for access violation when gcf
file is empty or sdr file is used
System : All
Modules : SystemConfig
Authors : rdb
Test #1 : On a system with empty GCF run systemconfig -bv -gcf:<gcffile>
Expect : SystemConfig should fail with "unable to parse XML file" message.

Issue : SystemConfig build verification failing for access violation with older
style GCF format
System : All
Modules : SystemConfig
Authors : rdb
Test #1 : On a system with older style GCF run systemconfig -bv -gcf:<gcffile>
Expect : SystemConfig should not get an access violation

Issue : SystemConfig output does not contain all pci ids for add in cards
System : North Shore
Modules : SystemConfig
Authors : rdb
Test #1 : On a North Shore with SAS controller in slot 1 and run SystemConfig -conf
Expect : SAS controller pci id to show up as a pcidevice

Issue : SystemConfig slot verification failing with older style GCF format
System : All
Modules : SystemConfig
Authors : rdb
Test #1 : On a system with older style GCF run systemconfig -bv -gcf:<gcffile>
Expect : Build verification should not fail for slot verification.

Issue : DF518253 Make LCD Front panel cable test optional on Indy (has LED front
panel)
System : Vince, Indy
Modules : Cables
Authors : robib
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : Should not fail on Indy with LED front panel

Issue : Added Cables support for Lanikai 7, Lanikai AIO, Olympic, Princeville
: Added LeftSpeaker, RightSpeaker, HardDrive, OpticalDrive, Camera,
IRDetector, and AVBoard
: in Windows Diagnostic User Guide
System : Lanikai 7, Lanikai AIO, Olympic, Princeville
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : Passing result and matches hardware configuration

Issue : Backplane connected to on-board SATA not displaying in conf

System : 12G
Modules : Disk
Authors : rdb
Test #1 : On a 12G server with BP connected to on-board SATA controller run disk -
conf
Expect : BP should be displayed NOT associated with any controller.

Issue : Orca PCIe SSD controller pci info not same as bridge pci info
System : 12g Servers with PCIe SSD
Modules : Disk
Authors : rdb
Test #1 : On a 12g server with PCIe SSD run disk -conf
Expect : PCIe SSD controller should have correct pci info for pcie ssd bridge
card. There should not be any
Controllers that have the same pci info as the PCIe SSD drives.

Issue : Orca with PCIe SSD not recognizing pcie ssd backplane
System : Orca
Modules : Disk
Authors : rdb
Test #1 : On an Orca with PCIe SSD drives run disk -conf
Expect : PCIE SSD drives and backplane should be displayed under PCIe SSD
controller.

Issue : DriveSectorType field missing from drives connected PCIe SSD and PERC
controllers
System : Servers
Modules : Disk
Authors : rdb
Test #1 : On an Orca with PCIe SSD drives run disk -conf
Expect : PCIE SSD drives should have DriveSectorType field with data
Test #2 : On a system with drives connected PERC controller run disk -conf
Expect : All drives should have DriveSectorType field with data

Issue : DF512830: CP&PB-"Cables" runs error in ePSA diagnostics

System : Cypress Point, Pebble Beach
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : Passing result and hardware matches Cypress Point configuration

Issue : Cleaned up code to indicate "Unknown" where applicable

System : Notebooks
Impact : Factory
Modules : nbpanel
Authors : vm
Test #1 : Run nbpanel -conf on a good number of notebooks.
Expect : Display configuration information.

Issue : CR478528: Add number of cells in battery to config output

System : Notebooks
Impact : Factory
Modules : battery
Authors : vm
Test #1 : Run battery -conf on a good number of notebooks.
Expect : Display Design Capacity in Wh. Number of cells is unreliable, hence not
displayed.

Issue : Add store/restore slot verification to SystemConfig

System : All
Impact : Customer and Factory
Modules : SystemConfig
Authors : rdb
Test #1 : Run SystemConfig -bv -store. Hot swap a HDD to another slot. Run
SystemConfig -bv -restore.
Expect : System should fail -restore command.

Issue : CR517707 Re-enable EPSA IPMI Fan test.

Systems : All with IPMI
Impact : Factory and Customer
Modules : fan
Authors : rods
Test #1 : Run "fan -conf"
Expect : The fans should be detected and configuration show.
Test #2 : Run "fan"
Expect : The test should Pass. The test has been re-enabled.

Issue : Added Cables support for Bullit

System : Bullit (PE M820)
Modules : Cables
Authors : bbw
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : Passing result and matches hardware configuration

Build 6026
-----------------------------------------------------------------------------------
----------------------------------

Issue : Add -ignorePreviousFailure switch for DST

System : All
Module : Disk
Author : rdb
Test #1 : On a system with an hdd that has previously failed DST run disk -f:7 -mon
Expect : DST should run.

Issue : Orca XD, Madone and Mojo conf output for Backplane does not have
connector information
System : Orca XD, Madone, Mojo
Module : Disk
Author : rdb
Test #1 : On an Orca XD run disk -conf
Expect : BP information should have number of slots x drive size.
Test #2 : On a Madone with BP connected to on board controller run disk -conf
Expect : BP information should be included in conf output and have the number of
slots x drive size.
Test #3 : On a Mojo run disk -conf
Expect : BP information should have number of slots x drive size.

Issue : Orca with 14 drives failing drive buffer test.

System : Orca
Module : Disk
Author : rdb
Test #1 : On an Orca with 14 drives run disk -f:1 -mon
Expect : All tests pass

Issue : North Shore with PERC6i and SATA drives in RAID1 failing randomseek test
System : North Shore
Module : Disk
Author : rdb
Test #1 : On a North Shore with PERC6i and 2 SATA drives in RAID1 config run disk -
f:5
Expect : All tests pass

Issue : Milky Way missing MotherBoardSlot tag in conf output

System : Milky Way
Module : Disk
Author : rdb
Test #1 : Run disk -conf
Expect : MotherBoardSlot tag should be in conf output for Optical devices

Issue : BSLN having a BSOD when running disk

System : Big Sur, Little Sur, Negril
Modules : Disk
Authors : rdb
Test #1 : Run Disk -conf
Expect : No BSOD

Issue : Milky Way failing ide_diag

System : Milky Way
Modules : Disk
Authors : rdb
Test #1 : On a Milky Way with 2 drives in RAID and 1 drive not in RAID run disk -
f:5 -mon
Expect : All test should pass.

Issue : DF512874 Incorrect TPMType output on STPM MBs in cables module

System : All systems that used GPIO 33 in their cables module
Impact : Customer and Factory
Modules : cables
Authors : haimingw
Test #1 : On a 12 G system with PIM TPM module run command cables.exe -conf
Expect : TPM status should be TPMonSocketPIM
Test #2 : On a system which used GPIO 33 run cables.exe
Expect : verify mfgmodejumper to be in the right status

Issue : Add Disk support for Milky way

System : Milky Way
Impact : Customer and Factory
Modules : disk
Authors : rdb
Test #1 : On a Milky Way run disk -conf
Expect : All devices should be displayed correctly including slot numbers.
Test #1 : On a Milky Way run disk -f:5 -mon
Expect : All tests should pass.

Issue : CR513172:[ALL] add switch for a non-interactive media test

System : All
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : Insert CD in optical drive and run disk -d:cdrom -f:4 -mon
Expect : All tests pass and CD will not eject.

Issue : Big Sur GList failure on SAS drives

System : Big Sur
Impact : Customer and Factory
Modules : disk
Authors : rdb
Test #1 : On a Big Sur with SAS drives run disk -f:10 -mon
Expect : Test should pass.

Issue : RIOS MLK did not run DST

System : RIOS MLK
Impact : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : On a RIOS MLK with 2 drives in a RAID 1 run disk -f:7 -mon
Expect : Test should run and pass.

Issue : Horton has CDROM in wrong slot when in S100 RAID mode
System : Horton
Impact : Customer & Factory
Modules : Disk
Authors : rdb & marky
Test #1 : On a Horton with ODD and S100, set up a RAID 1 and run "disk -conf"
Expect : All devices should be displayed in the correct slots.

Issue : DF509665 Fix FFFFFFFFC0000005 == -1073741819 errorlevel (crash) returned

intermittently by systemConfig
Systems : servers and notebooks
Impact : Factory & Customer
Authors : marky, robib, bradw
Modules : systemconfig
Test #1 : run systemconfig -xml in a loop
Expect : systemconfig should not crash

Issue : Add CancelConsistenctCheck for PERC Logical Drives

Systems : North Shore
Impact : Factory & Customer
Authors : rdb
Modules : Disk
Test #1 : On a system with PERC controller with a RAID 0 and a RAID 1 run disk -f:3
-mon
Expect : All tests pass.

Issue : Add DriveSectorType field to conf output for 512n, 512e and 4k sector
size drives
Systems : All
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : Run disk -conf
Expect : For 512n HDD DriveSectorType should have 512n, for 512e HDD
DriveSectorType should have 512e and
: for 4k HDD DriveSectorType should have 4k.

Issue : DF496923: Orca ePSA does not properly report on the risers.
Systems : Orca and Madone
Impact : Factory & Customer
Modules : Cables
Authors : haimingw
Test #1 : cables.exe -conf
Expect : riser information is listed as riser 1, riser 2 and riser 3 instead of
riser A, riser B and riser C.
Issue : DF496252 Orca ePSA Diags Event Log showing "critical" events with
"warning" icons. This is primarily a
: change for ePSA, but the shared source could affect Windows diags.
Systems : All IPMI
Impact : Factory, Customer
Modules : Memory, ServerMgmt, Eventlog
Authors : rods
Setup : Copy the following lines to a file (t.raw) and shift them over to start
in column 1:
#!Evlog x.x raw data file, SysID=0x0, Vendor=dell, Type=ipmi, Ver=0x20
0x02 0x00 0x02 0xAE 0x84 0x5D 0x4E 0x20 0x00 0x04 0xC5 0xF5 0x6F 0x00
0xFF 0xFF #Infor - unknown OEM event
0x03 0x00 0x02 0xAE 0x84 0x5D 0x4E 0x20 0x00 0x04 0xC0 0xF5 0x6F 0x00
0xFF 0xFF #Normal - Performance restored
0x04 0x00 0x02 0xAE 0x84 0x5D 0x4E 0x20 0x00 0x04 0xC2 0xF5 0x6F 0x02
0xFF 0xFF #Warning - QPI link width degraded
0x05 0x00 0x02 0xAE 0x84 0x5D 0x4E 0x20 0x00 0x04 0xC1 0xF5 0x6F 0x02
0xFF 0xFF #Critical - Failed link tuning
0x06 0x00 0x02 0xAE 0x84 0x5D 0x4E 0x20 0x00 0x04 0x01 0x01 0x07 0x03
0xFF 0xFF #NonRecoverable
0x07 0x00 0x02 0x00 0x00 0x00 0x00 0xB1 0x00 0x04 0x0C 0x01 0x6F 0xA0
0x80 0x01 #Critical - Dimm A1 error
Run "eventlog -clear:ipmi"
Run "eventlog -selfile:t.raw -write"
Test #1 : Run "eventlog"
Expect : The last four events above should be shown and the program should
indicate a failure.
Test #2 : Run "servermgmt"
Expect : The last four events above should be shown and the program should
indicate a failure.
Test #3 : Run "memory -f:20"
Expect : At the start of the test, it should show a line indicating the ECC error.
You can abort the test
: (ctrl-c) after this.
Cleanup : Run "eventlog -clear:ipmi".

Issue : GPIO access on ESB2 chipset -- not working for PSWD jumper on Teva
Systems : Teva, Teva-OEM
Impact : Factory
Modules : Cables
Authors : carl
Test #1 : Cables.exe (with the password jumper removed)
Expect : Test to show the REQUIRED password jumper is in error.
Test #2 : Cables.exe (with the password jumper installed)
Expect : Test to pass since the signal is in the proper state for Installed.

Issue : CR508292 : Add custom output of MAC address for Intel WiMAX card.
Systems : any system with the card installed
Impact : Factory
Modules : DDUsbDiag.exe
Authors : carl
Test #1 : Run ddusbdiag.exe -conf. The output will contain 4 additional lines when
the card is present.
Expect : Sample output listed below to show the 4 new XML tags for this card.
**Device**
DeviceName = Intel(R) Centrino(R) Advanced-N + WiMAX 6250
DeviceMnemonic = USBDEV:5
Commodity = USB_Device
USBId = 8086 0188
 VendorId = 8086
ProductId = 0188
Port = 5
IntelWimaxStr = 001DE10E5323 KP 0400040D
IntelWimaxMAC = 001DE10E5323
IntelWimaxChipId = KP
IntelWimaxCardId = 0400040D

Issue : Remove the "_" character from XML tags in the -conf output from Video.exe
Systems : All
Impact : Factory
Modules : Video.exe
Authors : carl
Test #1 : Run video.exe -conf -xml
Expect : All XML tags will be camel-cased words. The underscore character has been
removed.

Issue : DF510056 Fan Speed Failure

Systems : All with IPMI
Impact : Factory and Customer
Modules : fan
Authors : rods
Test #1 : Run "fan -conf"
Expect : The fans should be detected and configuration show.
Test #2 : Run "fan"
Expect : The test should Pass. Note that this test cannot fail on this version -
the test will be
: re-enabled in a future release.

Build 6025
-----------------------------------------------------------------------------------
----------------------------------

Issue : DF507065: 12G Validation - Orca fails build ver with delldiags 6025
Systems : Orca
Impact : Customer & Factory
Modules : Disk
Author : rdb
Test #1 : On an Orca with drives connected to motherboard controller run disk -conf
Expect : All drives should show correct motherboard slot

Issue : DF501572 [R620] ePSA 4214-3: cable test failed with 10 HDD system.
Systems : Madone
Impact : Factory & Customer
Modules : Cables
Author : haimingw
Test #1 : run cables.exe or epsa cables test on a 10 HDD Madone system
Expect : test should pass

Issue : DST Failures in 64Bit Windows

Systems : All
Impact : Factory
Modules : Disk
Author : rdb
Test #1 : On a 12g system with SSD that was failing previously for previous DST
error run disk -f:7
Expect : All tests should pass

Issue : CR478742 - Add Support for Intel SCU to Disk Module

Systems : Big Sur, Little Sur and Negril (BSLSN)
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On a BSLSN with SCU run disk -conf
Expect : All devices connected to SCU should be displayed under it
Test #2 : On a BSLSN with devices connected to SCU run disk -f:1 -mon
Expect : All tests pass

Issue : Display Controller:[Bay:]:Slot information for failing device

Systems : All
Impact : Factory & Customer
MOdules : Disk
Authors : rdb
Test #1 : On a system that has a bad disk run disk -f:1 -mon
Expect : Test should fail and device name should have (x:[y:]:z) after device
name. For systems without a
: backplane it should have (x:z) where x is the controller and z is the
slot. For systems with a
: backplane it should have (x:y:z) where x is the controller, y is the bay
and z is the slot.

Issue : CR480899 - modify cables to refresh the signal each time the test is
looped in WinPE or executed in ePSA.
Systems : all
Impact : Factory, Customer
Modules : Cables.exe
Authors : carl
Test #1 : Run the cables test in ePSA. Change the state of an Optional Cable,
Expect : The change of state is listed in the results buffer with a message
indicating a change since the Configuration tab was initialized.
Test #2 : Run the cables test in WinPE and loop the test. Change the state of an
Optional Cable,
Expect : The change of state is listed in the results buffer with a message
indicating a change since the module was initialized.
Test #3 : Initialze a cable/jumper/sensor so that it is in the FAIL condition on a
REQUIRED signal. Run the cables test in ePSA.
After the failure is noted, change the state of ths signal back to the
shipping condition. Run the cables test again
by clicking on the Cables tag or pressing Enter while the Cables test is
the selected test.
Expect : The change of state is listed in the results buffer with a message
indicating a change since the module was initialized.
The error message is cleared and the test now passes.

Issue : CR125 Update IPMI Fan test

Systems : All with IPMI Fans (most servers)
Impact : Factory, Customer
Modules : Fan.exe
Authors : rods
Test #1 : Run Fan.
Expect : The test should test the fans and report the results. The algorithm was
modified to more accurately
: measure the fan speed and stability. If the system does not allow
testing the fans, then test should
: Pass in factory build (N/A in customer build).

Issue : CR126 Update EventLog processing

Systems : All with IPMI event log (most servers)
Impact : Factory, Customer
Modules : ServerMgmt.exe, Eventlog.exe
Authors : rods
Test #1 : Run "eventlog -dump".
Expect : The events should be checked. If the system contains any OEM events,
they should have the event
: data dumped, but the event itself will still be unknown.
Test #1 : Eventlog.exe now has two options that allow it to read IPMI SEL events
from a file.
Expect : See the help on the two new parameters.

Issue : Added initial cables support for Oakmont, Pine Valley, Sunrise, Pebble
Beach, Cypress Point
Systems : Oakmont, Pine Valley, Sunrise, Pebble Beach, Cypress Point
Impact : Factory
Modules : Cables.exe
Authors : carl
Test #1 : Run "cables -conf"
Expect : Cables configuration to show current state of GPI signals.

Issue : CR506996: Add custom chip generation value tag to XML output for PCI
device 104A:7007 (Pink Panther Encryption/Decription card)
Systems : Any containing the PCI card with PCI ID of 104A:7007
Impact : Factory
Modules : systemconfig.exe
Authors : carl
Test #1 : systemconfig -conf
Expect : New ChipsetGeneration tag to appear in the config output for this card
and indicate the chipset generation as GEN1 or GEN2

Build 6024
-----------------------------------------------------------------------------------
----------------------------------

Issue : BTO497528: DellDiags 6022 Validation - Coaster fails build ver for RD1000

System : Coaster
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On a Coaster with RD1000, ODD and no HDDs run "disk -conf"
Expect : RD1000 should show up under IntelRAID Controller

Issue : Added 10g and 11g Backplane support to Disk

System : Servers with backplane
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On a 10g, 11g and 12g server that have backplane installed run "disk -
conf"
Expect : Backplane should show with <slot count> x <size> for the Model

Issue : DF500015 Orca XD: ePSA version 4214.3 does not properly report on
risers.
Systems : Orca, Orca-XD and Madone
Impact : Customer
Modules : Cables.exe
Authors : haimingw
Test #1 : Cables.exe -conf
Expect : PCIe slots on riser are named from slot 1 through slot 7 as indicated on
the silk screen.

Issue : Added Milky Way SSID and Cables support

System : Milky Way
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : Passing result and hardware matches Milky Way configuration

Issue : DF482450 : Clarify that a cable can be a cable, sensor, connection or

jumper in the error messages.
Systems : all systems
Impact : Factory
Modules : Cables.exe
Authors : carl
Test #1 : Cables.exe -xml
Expect : The error message, if a "cable" is not connected to indicate checking a
cable, sensor or jumper.

Issue : Jabba not having MotherBoardSlot field in conf output when in ATA mode.
System : Jabba
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a Jabba with SATA mode set to ATA run "disk -conf"
Expect : MotherBoardSlot field should be in HDD and ODD devices.

Issue : BTO496460:CCC Server WBT issue: Diamas DST test fail. Daimas with SATA
drives connected to
: H200 failing GList for SMART state failure
Systems : Daimas
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On a Daimas with SATA drives connected to H200 run "disk -f:5 -mon"
Expect : All tests should pass.

Issue : Back Plane number and topology not being displayed in conf output for
Orca
Systems : Orca
Impact : Factory
Modules : Disk
Authors : rdb
Test #1 : On an Orca run "disk -conf"
Expect : Backplane device should have BackPlaneNumber field populated with the
correct back plane number
: and the model should be populated with the back plane topology.

Issue : CR478746: Add PCIE SSD support to disk

Systems : 12g servers
Impact : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : On a 12g server with PCIe SSD devices installed run "disk -conf"
Expect : PCIe SSD Controller and devies should be in conf output.
Test #1 : On a 12g server with PCIe SSD devices installed run "disk -f:2 -mon"
Expect : All tests should pass.
Build 6023
-----------------------------------------------------------------------------------
----------------------------------

Issue : Removed Heat Sink Clip Test for new cost reduced systems
System : Gold Coast, Tambor, Katsiki
Authors : billb, carla
Module : Cables
Test #1 : Run the ePSA version with this change on target systems HSclip GPIO open
and pulled up
Expect : Cables Test should pass and Config Tab does not show the Heat Sink Clip
Test

Issue : DF496923: Orca ePSA does not properly report on the risers
System : Orca
Authors : haimingw
Module : Cables
Test #1 : Cables.exe -conf
Expect : check that riser A, riser B and Riser C have the right slot card presence
information

Issue : Debug message printing in Disk

System : Servers with PERC
Authors : rdb
Module : Disk
Test #1 : On a server with a PERC card run Disk -conf
Expect : No debug messages displayed

Issue : CR478739: Build Verification to Perform Slot Verification (unofficial

release)
System : All
Authors : rdb
Module : SystemConfig, Disk
Test #1 : On a system with GCF appended to c:\dell.sdr run "SystemConfig -gcf:c:\
dell.sdr -bv -cfgout:system.xml"
Expect : Build verification should pass and systemconfig conf output should be in
system.xml.

Issue : Add Vince & Indy ssid's to cables definitions

System : Vince/Indy
Authors : robib
Module : cables
Test #1 : Run "cables.exe" on Vince & Indy
Expect : Verify cables output to PWA setup

Issue : Remove cables test for Service Mode Jumper as GPIO33 is not used and
GPIO56 is GPO signal
System : BSLSN
Authors : robib
Module : cables
Test #1 : Run "cables.exe" on BSLSN
Expect : Verify cables output to PWA setup

Issue : CR494038 Update TPM identification according to newly release schematic

System : Orca, Orca-XD, Madone and Ghostrider
Authors : haimingw
Module : cables
Test #1 : Run "cables.exe -conf" on a system with ROW TPM
Expect : It should tell that ROW TPM is installed
Test #2 : Run "cables.exe -details" on a system with ROW TPM
Expect : It should display installed ROW TPM and all TPM pattern definitions

Issue : DF489575 Mojo-ePSA can not detect Mezz card

System : Mojo
Authors : bbw
Module : Cables
Test #1 : On a Mojo system, confirm with cables the Mezz card installed/not
installed correct.
Expect : Installed/Not Installed condition of Mezz[BC]1 match HW configuration.

Issue : Add Blur and Hi-Fi to cables module

System : Blur and Hi-Fi
Authors : bbw
Module : Cables
Test #1 : Run cables on target machine
Expect : Confirm that the test shows passed for target platform.

Issue : Add support for "Video Resolution" in the configuration for notebooks
System : All notebooks
Authors : vm
Module : nbpanel
Test #1 : Run "nbpanel -conf"
Expect : Confirm that the Video Resolution is listed in the configuration.

Issue : Added support for LSI9265 HDD Controller

System : Scooby
Authors : rdb
Module : Disk
Test #1 : On a Scooby with LSI9265 HDD Controller run "disk -conf"
Expect : Disks connected to the LSI9265 should show up under the LSI9265 HDD
Controller
Test #2 : On a Scooby with LSI9265 HDD Controller run "disk -f:3 -mon"
Expect : All tests should pass

Issue : Miscellaneous IPMI and ServerMgmt updates

: IPMI - Fix incorrect SDR indicating a sensor uses a units modifier
: IPMI - Fix decoding that caused some sensors to display incorrectly as a
negative value
: IPMI - Try to detect a dead interface
: IPMI - Additional check made for iDrac presence
: IPMI - Decode of some non-Dell OEM IPMI commands
: IPMI - Fix a couple of debug messages that were bypassing the library
filter
: ServerMgmt - Add new factory Sensor command to dump sensor readings
: ServerMgmt - Function variable was too small to hold all possible
function enums.
System : 12G Servers
Authors : rods
Modules : Memory, ServerMgmt, EventLog, Fan
Test #1 : Run modules as normal.
Expect : The only user detectable change is for a system where the BMC is not
working - the program
: should give up on the interface easier.
Test #2 : Run factory build "servermgmt -sensor".
Expect : New test that should format the sensor values.

Issue : Update IPMI Fan support.

System : 12G Servers
Authors : rods
Modules : Fan
Test #1 : Run module as normal.
Expect : No change to the configuration.
: Measuring fan speed should be faster on systems with many fans.
: A fan that shows 0 RPM at low and high speed is flagged as potentially
missing.

Build 6022
-----------------------------------------------------------------------------------
----------------------------------

Issue : DF453138 : Slinky and Skipper do not display MotherBoardSlot tag

System : Slinky and Skipper
Authors : rdb
Module : Disk
Test #1 : Run "disk -conf"
Expect : Verify MotherBoardSlot tag to be displayed for ODD and any HDD connected
to on-board controller.

Issue : Phobos has incorrect MotherBoardSlot information for ODD

System : Phobos
Authors : rdb
Module : disk
Test #1 : On a Phobos with ODD connected to motherboard connector 6 or 7 run "disk
-conf"
Expect : MotherBoardSlot tag for ODD device should have correct information

Issue : RD1000 connected to S100 controller does not display MotherBoardSlot

information.
System : Server with RD1000
Authors : rdb
Module : disk
Test #1 : On a server with RD1000 connected to S100 controller run "disk -conf"
Expect : MotherBoardSlot tag for RD1000 device should have correct information

Issue : RIOS-MLK missing MotherBoardSlot information for ODD

System : RIOS-MLK
Authors : rdb
Module : disk
Test #1 : On a RIOS-MLK with ODD, 2 HDDS in a RAID0 and 1 HDD disconnected run
"disk -conf"
Expect : MotherBoardSlot tag for ODD device should have correct information

Issue : North Shore failing Verify test

System : North Shore
Authors : rdb
Module : disk
Test #1 : Run "disk -f:5 -mon"
Expect : All tests should pass

Issue : Fix for DF453138 broke MotherBoardSlot info for other systems with Intel
RAID cotrollers
System : RIOS MLK
Authors : rdb
Module : disk
Test #1 : On a Diamas or Coaster with TBU connected to LSI SCSI card run "disk -
conf"
Expect : MotherBoardSlot field should be valid.
Test #2 : On a RIOS MLK in RAID mode run "disk -conf"
Expect : MotherBoardSlot field should be valid.
Test #3 : On a RIOS MLK in AHCI mode run "disk -conf"
Expect : MotherBoardSlot field should be valid.

Issue : DF453138: Devices detected on wrong SATA ports for Diamas and Coaster
System : Diamas and Coaster
Authors : rdb
Module : disk
Test #1 : On a Diamas or Coaster with TBU connected to LSI SCSI card run "disk -
conf"
Expect : Slot field should be valid.

Issue : Systems with AMD RAID controllers in AHCI mode do not display
MotherBoardSlot field in conf output
System : All desktops with AMD RAID controllers.
Authors : rdb
Module : disk
Test #1 : On a system with AMD RAID controller in AHCI mode run "disk -conf"
Expect : MotherBoardSlot field should display correct slot information for each
device connected to the controller.

Issue : Drives connected to SWRAID controllers had DriveChannelId controller

number field set to -1
System : Servers with SWRAID S100/S300 controller
Authors : rdb
Module : Disk
Test #1 : On a system with drives connected to an S100 or S300 controller run "disk
-conf"
Expect : DriveChannelId controller number field greater than -1

Issue : Orca backplane with FW version 0.10 or later did not show up in conf
System : Orca
Authors : rdb
Module : Disk
Test #1 : On an Orca with backplane fw 0.10 or greater run "disk -conf"
Expect : BP device should show up in conf with correct fw version.

Issue : SD devices connected to Multi-Card slot were not being tested

System : Shakira
Authors : rdb, billb
Module : Disk
Test #1 : On a Shakira insert SD card into multi-card slot and run "disk -f:1 -
d:HDDMCARD -mon"
Expect : All tests should pass

Issue : CR481483: Delldiag add support to report true controller order and slot
ID
System : Mission Hills
Authors : rdb
Module : Disk
Test #1 : Run "Disk -conf"
Expect : HDDs connected to correct ports on the Motherboard

Issue : HDDs connected to PERC controller have DriveChannelId set to -1:n

System : Servers with PERC
Authors : rdb
Module : Disk
Test #1 : On a server with a PERC run "disk -conf"
Expect : DriveChannelId should have x:n where x is the controller number and n is
the slot number

Issue : RAID arrays being tested for GList errors

System : All systems with RAID
Authors : rdb
Module : Disk
Test #1 : On a system with a RAID set up run "disk -f10"
Expect : Only true hard drive devices should be tested. RAID arrasy should not be
tested.

Issue : Katsiki with mixed RAID config with RAID / Non-RAID drives not displaying
in correct slots
System : Katsiki
Authors : rdb
Module : Disk
Test #1 : On a Katsiki with 3 drives set 2 drives in a RAID and the 3rd leave as
non-RAID. Run "disk -conf"
Expect : All HDD and ODD devices should show up in the correct mother board slot.

Issue : Add custom keys for paxton keyboard - secure rotate and tools
System : Paxton
Authors : robib
Module : Keyboard
Test #1 : On a Paxton check run keyboard and check for secure, tools and rotate
keys
Expect : scan keys recognized and custom keys displayed

Issue : DF482450 Error while running diags: "Check the following cables:
Password Jumper"
System : Orca, Orca-XD, Madone and Ghostrider
Authors : haimingw
Module : Cables
Test #1 : Run cables test
Expect : Missing password jumper doesn't fail the cables test

Issue : Cables XML output on some systems is not valid and not parseable
System : Orca, Orca-XD, Madone and Ghostrider, etc
Authors : marky, haimingw
Module : Cables
Test #1 : Cables -xml -details -o:xml.txt
Expect : Verify IE does not complain about syntax when you run 'Start xml.xml'

QFR Build 6021.6:

-----------------------------------------------------------------------------------
----------------------------------

Issue : Disk failing with memory access issue

System : Servers with PERC controller
Authors : rdb
Module : Disk
Test #1 : On a server with an HDD connected to a PERC controller run "disk -conf"
Expect : Conf output with no errors

Issue : Some BIOSs were returning invalid data for the thermal sensors. Added up
too 3 retries before failing
: the sensor.
System : All
Authors : bjt
Test #1 : Sysman.exe, Let it run over night.
Expect : The test should pass when aborted.

QFR Build 6021.5:

-----------------------------------------------------------------------------------
----------------------------------

Issue : Added HDD controller PCI ID to device connected to the controller conf
output. For future use with
: slot verification
System : All
Module : Disk
Authors : rdb
Test #1 : Run "disk -conf"
Expect : ControllerPciId field to contain HDD Controller PCI ID

Issue : DF473857:MicroSoft returns "?" for the device name if it can't identify
the device. To work around this
: the code was changed to return the Vendor/Device IDs as the device name
when this is the case.
System : ALL
Modules : DDUsbDiag
Authors : bjt
Test #1 : DDUsbDiag.exe
Expect : Validate that "?" is NOT displayed as the device name.

Issue : Added Comoros SSID and Cables support

System : Comoros
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : Passing result and hardware matches Comoros configuration

Issue : Made CPUriser OPTIONAL

System : Lotto
Modules : Cables
Authors : billb
Test #1 : Run Cables
Expect : Passing result

Issue : Added Chipset thermal sensor

System : Shakira
Modules : Thermals
Authors : billb
Test #1 : Run Thermals
Expect : Chipset Sensor results with the updated Shakira BIOS

Issue : Horton failing SMART check

System : Horton with H200
Modules : Disk
Authors : rdb
Test #1 : On a Horton with SATA drives connected to H200 run "disk -f:2 -mon"
Expect : All tests should pass.

Issue : Removed "virus" from bootpath messages.

System : all
Modules : Bootpath
Authors : mikel
Test #1 : Run bootpath
Expect : Should not see any messages about virus.

Issue : CR483142 WBDD & ePSA Disable BSM and SPD log parsing
System : All servers
Modules : eventlog library (Memory, eventlog)
Authors : rods
Test #1 : Run "eventlog -conf"
Expect : The "SPD" and "BSM" logtypes should not appear.

Issue : CR483143 WBDD Add eventlog parameter to clear all available logs
System : All
Modules : eventlog.exe
Authors : rods
Test #1 : Run "eventlog -clear:all"
Expect : The program will attempt to clear all the logs that it can find. Note
that some
: logs (like DMI) cannot be cleared by this program, but that is not a
failure.

QFR Build 6021.2:

-----------------------------------------------------------------------------------
----------------------------------

Issue : DST abending on SATA drives connected to S300 controller

System : Servers with S300 and SATA drives
Modules : Disk
Authors : rdb
Test #1 : On a server with SATA drives connected to an S300 controller run "disk -
f:7 -mon"
Expect : Test should pass

Issue : Fixed PlanarID, Heatsink signals on McCave. Also made optional

: cpu1, pwrsply1 on CindyLou, Yertle
System : McCave, CindLou, Yertle
Modules : Cables
Authors : robi
Test #1 : Run cables on above systems
Expect : Test should pass

Issue : Fixed PlanarID signals on Sneetch. Made cpu0 optional

System : Sneetch
Modules : Cables
Authors : haiming
Test #1 : Run cables on above systems
Expect : Test should pass

Issue : Changed the Sysman.exe default max temp from 150c to 100c.
System : All
Modules : Sysman
Authors : bjt
Test #1 : Run sysman and verify that the module fails when 100c is read.
Expect : Test should fail at 100c by default.

Issue : Added cables support for Orca XD, Orca, Madone and Ghostrider
System : Orca XD, Orca, Madone and Ghostrider
Modules : Cables
Authors : haimingw
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : Cables will pass with the Required cables installed
Issue : The diags did not support 4k EEPROM page sizes which some BIOS were
using.
This caused ePSA diag results to not get logged.
System : Test all systems, but fixes Firestore, Andrews, Mission Hills, SawGrass
and Palm Beach.
Modules : EventLog.exe
Authors : bjt
Test #1 : Run the ePSA diags. This will log results to the EEPROM. Then run
eventlog.exe.
Expect : ePSA results should be correctly reported in eventlog.exe.

Issue : Version support added to dddriver.sys.

System : All
Modules : All
Authors : bjt
Test #1 : Run all windows based tests.
Expect : Everything should run correctly.

Issue : Add Processor module (CR478513)

System : Notebooks
Modules : Processor
Authors : mikel
Test #1 : Run Processor
Expect : Will run CPU stress.

Issue : Added DriveChannelID to Disk -conf output so Bay will be included for 12G
systems
System : All
Modules : Disk
Authors : rogerb
Test #1 : Run disk -conf
Expect : DriveChannelID will be in conf output

Issue : CR478532 : Change SystemConfig to run multithreaded

System : All
Modules : SystemConfig
Authors : rogerb
Test #1 : Run SystemConfig -conf
Expect : Conf output to contain all expected devices

Issue : CR479139: WBDD:VARIOUS:RM:Change Audio Cable OPTIONAL back to REQUIRED

System : Big Sur, Little Sur, Negril, Katsiki, Tambor
: Gold Coast, Lotto, Lotto Lite, New Balance, Comiskey, Arrowhead, Azteca
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : Cables will pass with the Required cables installed

Issue : Added Andromeda cables support

System : Andromeda
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : Cables will pass with the Required cables installed

Issue : SATA drives were not being checked for prior DST failures
System : All
Modules : Disk
Authors : rdb
Test #1 : On a system that has a SATA drive with a prior dst failure in the SMART
log run "disk -f:7 -mon"
Expect : System should fail.

Issue : On some systems the video test is taking too long to complete the test.
Working with test strategy we
changed the tests that get run at the various test levels. The following
table lists the test algorithm
that get run.

<Level 0> Scan Test

<Level 1> MarchLR, MATS
<Level 2> MarchC, WMchC, WMats
<Level 3> Scan, Stress, Integrity1, Integrity2, MarchC, MarchLR, WMatsP,
WMchC, XMats32S, Mats, WdPcMch, MovI
System : All
Modules : Video.exe
Authors : bt
Test #1 : Run "Video.exe"
Expect : Test time should be reduced.

Issue : Fix WBT IPMI command retry.

System : Any with IPMI and iDrac6 or later.
Modules : Ipmilib users (Memory, eventlog, cables, fan)
Authors : rods
Test #1 : Run "fan.exe", then run "eventlog.exe".
Expect : Both modules should run (may find errors), but there should not be a
message from WinIPMI.DLL for missing
: command string data.

Issue : Added detailed messages for front panel LCD failures: wrong color, wrong
character, bad command
: completion code.
System : Any with IPMI front panel LCD or iDRAC6 support.
Modules : Servermgmt
Authors : fritzk
Test #1 : Servermgmt
Expect : see SEL,SDR, and non-interactive tests
Test #2 : Servermgmt -i -fplcdtest (answer all questions correctly/matching the
display).
Expect : test should prompt and pass.
Test #3 : Servermgt -fplcdtest
Expect : the same thing as servermgmt (runs the SEL, SDR, and LCD test.

Issue : Add support for filtering log events to Delldiag log, client bios log,
DMI log.
System : Client systems
Modules : eventlog users (Memory, Eventlog)
Authors : rods
Test #1 : Run "memory.exe" and "eventlog.exe" as normal.
Expect : The memory module should no longer show failures for non-memory related
entries (e.g a broken fan).

Issue : Add support for VRAM testing for the systems listed below.
System : Vostro 1320 HALF_PENNY_BRIDGE_S
Vostro 1520 (portable) HALF_PENNY_BRIDGE_M
Vostro 1720 HALF_PENNY_BRIDGE_L
Precision M2400 (portable) HEELYS NVidia
 Latitude E6500 MAYBACH
Alienware 17" AW_QUICKSILVER (NVIDIA, Penryn, MCP79-SLI)
XPS 1340 (portable) JOLIE
Modules : Video
Authors : bt
Test #1 : Run "Video.exe -f:1".
Expect : The should pass.

Issue : CR477431 Support IPMI SEL change to logging format.

Systems : All IPMI-based servers 9G and later.
Modules : ipmi10.mdm, smbios.mdm
Authors : rods
Setup : Copy these lines to file "ecc.raw". (shift them left to margin)
#!Evlog x.x raw data file, SysID=0x0, Vendor=dell, Type=ipmi, Ver=0x20
# Created Jul 07 13:12:40 2005
0x00 0x00 0x02 0x00 0x00 0x00 0x00 0xB1 0x00 0x04 0x0C 0x01 0x6F 0xA0
0x00 0x01
0x00 0x00 0x02 0x00 0x00 0x00 0x00 0xB1 0x00 0x04 0x0C 0x01 0x6F 0xA0
0xF0 0x01
0x00 0x00 0x02 0x00 0x00 0x00 0x00 0xB1 0x00 0x04 0x0C 0x01 0x6F 0xA0
0x80 0x01
0x00 0x00 0x02 0x00 0x00 0x00 0x00 0xB1 0x00 0x04 0x0C 0x01 0x6F 0xA0
0xB0 0x01
0x00 0x00 0x02 0x00 0x00 0x00 0x00 0xB1 0x00 0x04 0x0C 0x01 0x6F 0xA0
0xC0 0x01
0x00 0x00 0x02 0x00 0x00 0x00 0x00 0xB1 0x00 0x04 0x0C 0x01 0x6F 0xA0
0xD0 0x01
0x00 0x00 0x02 0x00 0x00 0x00 0x00 0xB1 0x00 0x04 0x0C 0x01 0x6F 0xA0
0xE0 0x01
0x00 0x00 0x02 0x00 0x00 0x00 0x00 0xb1 0x00 0x04 0x0C 0x02 0x6F 0xA2
0xF0 0x01
: Run "eventlog -write:ecc.raw" to put the events in the log.
Test #1 : "eventlog -all"
Expect : Should be able to format all of the records showing an ECC error on
: the first dimm and an IBIST error on the same dimm. There should
: not be any records with "Event Data xx/xx/xx" formats.
Cleanup : Run "eventlog -clear:ipmi" to clear the log.

Issue : Wingui prints: Warning BootPath.exe not found

System : All
Modules : WinGui
Authors : marky
Test #1 : Wingui
Expect : The warning message is not displayed in console.

Issue : TopHat Health LED initial support, combining the current LCD test and
vendor
: specific IPMI code.
System : iDRAC LCD systems and TopHat
Modules : Servermgmt
Authors : fritzk
Test #1 : servermgmt
Expect : non-interactive sel/sdr/lcd (no run on TopHat, no failure on TopHat).
Test #2 : servermgmt -i
Expect : interactive, no errors on TopHat.

Issue : DF474665 PSA diags Orca PE-R720 No fan diagnostics.

Systems : All IPMI-based servers
Modules : Fan, Ipmi library, eventlog library
Authors : rods
Test #1 : Run "Fan"
Expect : IPMI Fan should operate as before under WBDD.

Issue : CR479070 WBT RM Simplify ServerMgmt iDrac info collection

Systems : All IPMI-based servers
Modules : ServerMgmt
Authors : rods
Test #1 : Run "Servermgmt -firmwareID"
Expect : Should collect and display the iDrac firware info.

Issue : DF480123 Need Power Distribution Board cable detect added.

CR480123 Add IOH2 heat sink clip detection.
Systems : NorthShore
Modules : Cables.exe
Authors : carl
Test #1 : Cables.exe -xml
Expect : Cables to pass if PDB cable is plugged in. Expect it to fail if PDB cable
is not plugged in.
Expect : IOH2 heat sink detection status to follow conditions of the HS clip.

Build 6020:
-----------------------------------------------------------------------------------
----------------------------------

Issue : Added cables support for Orca, Madone, Ghostrider and OrcaXD.
System : Orca, Madone, Ghostrider and OrcaXD
Modules : Cables
Authors : hw
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : Cables will pass with information about system cable status

Issue : Added Mojo(M620) cables support

System : Mojo
Modules : Cables
Authors : bbw
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : Cables will pass with information about Mojo cable status

Issue : Changed Audio cable from REQUIRED to OPTIONAL for WBT and ePSA
: <<No change for USFF & small Systems with no Plugin Audio Card option>>
System : Big Sur, Little Sur, Negril, Turnberry, Riveria, Mission Hill, Sawgrass,
Palm Beach, Katsiki, Tambor
: << WBT only, not ePSA: Gold Coast, Chen Long, Fleming, Lotto, Lotto Lite,
New Balance, Comiskey, Arrowhead, Azteca
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : Cables will pass with the Required cables installed

Issue : Added Lanikai cables support

System : Lanikai
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : Cables will pass with the Required cables installed

Issue : Sysman was not updating the thermal sensors when running.
System : All client
Modules : Sysman
Authors : bt
Test #1 : Sysman.exe
Expect : Verify that the thermal sensors update every 60 seconds.

Issue : Corrected TouchPanel cable GPIO

System : Firestone, Andrews
Modules : Cables
Authors : billb
Test #1 : Run Cables, Cables -conf, Cables -details
Expect : Cables will pass with TouchPanel cable installed and password jumper not
installed

Build 6019: Released

-----------------------------------------------------------------------------------
----------------------------------

Issue : Add Jet Li ChassisID

System : Jet Li
Modules : Cables
Authors : billb
Test #1 : cables -conf
Expect : MiniTower or Desktop should appear

Issue : Add Turnberry and Riviera Cables Test for ePSA4212

System : Turnberry and Riviera
Modules : Cables
Authors : billb
Test #1 : Run ePSA
Expect : Verify Cables in the Config Tab

Issue : Add BSLSN desktop SSID to Fan Module

System : BSLSN
Modules : Fan
Authors : robib
Test #1 : Test Fan module on BSLSN
Expect : Should Pass once BIOS support implemented

Issue : RD1000 connected to S100 not being displayed in conf output.

System : ESG with S100
Modules : Disk
Authors : rdb
Test #1 : On a system with S100 and RD1000 run "disk -conf"
Expect : RD1000 should show up under the S100 controller

Issue : DF453138 : DellDiags detects optical drive on incorrect port.

System : All
Modules : Disk
Authors : rdb
Test #1 : On systems with SATA devices connected to motherboard SATA ports run
"disk -conf"
Expect : slot information should be correct (0 based).

Issue : IPMI/EventLog changes

: Add IPMI eventlog write - factory only
: Function name change fEvlogNextFailingEvent to fEvlogNextReportableEvent
to be more accurate.
: Add command packet retry via WMI if the interface is BUSY.
: Change several SEL events from Critical to Warning or Normal for more
realistic usage.
: Change users to not fail on Warning events - still want the user to see
them, but not a test failure.
System : All
Impact : Customer & Factory
Modules : Memory, EventLog
Authors : rods
Test #1 : Run diags.
Expect : All diags should run with no errors.

Build 6018: Released

-----------------------------------------------------------------------------------
----------------------------------

Issue : The diagnostic drivers failed to load on 64bit Win7 images. The diag
drivers are not digitally signed.
System : All
Impact : Customer & Factory
Modules : All
Authors : bjt
Test #1 : Run diags.
Expect : All diags should run with no errors on 64bit Windows 7.

Issue : SCSI Verify test failing

System : Servers
Impact : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : Run "disk -f:1 -mon"
Expect : All tests should pass.

Issue : SCSIBuffer test failing

System : Servers
Impact : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : Run "disk -f:3 -mon"
Expect : All tests should pass.

Issue : Remove thermal sensor support on Braxton, BIOS was hanging on the calls
to read the sensors.
Systems : Braxton
Impact : Customer and Factory
Modules : Sysman
Authors : BryanT
Test #1 : Run ePSA
Expect : Verify there are no hangs.

Issue : Add IPMI library function to detect the presence of an iDrac.

Systems : All
Impact : Customer and Factory
Modules : IPMI library
Authors : rods
Test #1 : No specific test.
Expect : Changes to support future video updates.

Issue : Fix Power Supply FRU retrieval.

Systems : All IPMI with Power Supply FRUs
Impact : Customer and Factory
Modules : ServerMgmt
Authors : rods
Test #1 : Run "servermgmt -conf -xml"
Expect : Verify the config with tag <PSU> contains valid data.

Issue : Misc IPMI updates. Replace hardcoded commands with defines. Update
several status checks after calls to
: fIpmiCommand.
Systems : All IPMI
Impact : Customer and Factory
Modules : ServerMgmt, Fan
Authors : rods
Test #1 : Run "servermgmt -conf -xml"
Expect : Verify the config with tag <PSU> contains valid data.
Test #2 : Run "fan"
Expect : Verify the fan(s) test correctly.

Issue : Modified IPMI sel chk library form warning to normal for missing
controller. Support no HD no Cntrl config.
System : All IPMI
Impact : Customer and Factory
Modules : Servermgmt
Authors : fritzk
Test #1 : servermgmt on a system with no HD or controller.
Expect : Pass on SEL check

Build 6017.7 : Released

-----------------------------------------------------------------------------------
----------------------------------

Issue : SCSIBuffer test failing

System : Servers
Impact : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : Run "disk -f:3 -mon"
Expect : All tests should pass.

Issue : Anakin having an extra drive in conf output without any drive information
System : All AMD systems
Impact : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : On an Anakin set run "disk -conf"
Expect : Only one drive to show up and it should be associated with under the AMD
controller

Issue : BTO457333 : SIDIOUS failing HDD Stress Test

System : Sidious
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On a Sidious with a single drive run "disk -conf"
Expect : Only 1 drive should show up under the AMD controller
Test #2 : On a Sidious with a single drive run "disk -f:4 -mon"
Expect : All tests should pass

Issue : Tambor with Liteon SSD failing ReadVerify and RandomSeek Tests
System : Tambor with Liteon SSD
Impact : Factory & Customer
Modules : Disk
Authors : rdb & billb
Test #1 : run "disk -f:5 -mon"
Expect : All tests should pass.

Issue : Coaster with Seagate 300GB drive that has been modified to be 146GB
failing ScsiBuffer test
System : Coaster with Seagate 300GB drive that has been modified to be 146GB
Impact : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : run "disk -f:1 -mon"
Expect : All tests should pass.

Issue : Fixed Video memory test issue on Panerai and PhantomMLK.

Excluded some legacy systems that aren't supported in the video test.
Systems : All
Impact : Factory
Modules : video
Authors : mikel
Test #1 : run "video -f:0"
Expect : Test should pass on valid HW.

Issue : Memory TS requests memory available and allocated size from memory test
Systems : All
Impact : Factory
Modules : memory
Authors : bradw
Test #1 : run "memory -f:1"
Expect : output should contain MemoryAvailable and MemoryAllocated fields

Issue : SCSIBuffer test failing for 0 byte size buffer

Systems : Veso
Impact : Factory & Customer
Modules : Disk
Authors : rogerb
Test #1 : run "disk -f:1 -mon"
Expect : system should pass all tests

Issue : Modifying cables test for servers to reflect actual cabling combinations
Systems : PE servers
Impact : Factory
Modules : Cables
Authors : fritzk
Test #1 : Run cables.exe
Expect : Test with systems previously showing cables related failures.

Issue : Changed Skywalker password jumper expected value to 1

Systems : Skywalker (MT, DT)
Impact : Customer
Modules : Cables
Authors : billb
Test #1 : Run cables, cables -conf
Expect : Cables Test will pass with the PSWD Jumper not in the reset position

Issue : Updated MH, SG, and PB Cable Support

Systems : Mission Hills, Sawgrass, Palm Beach (MT, DT, SFF)
Impact : Customer
Modules : Cables
Authors : billb
Test #1 : Run ePSA
Expect : Cables Test will fail when ChassisID Cable is unplugged
Test #2 : Run Cables.exe
Expect : Test will fail when ChassisID Cable is unplugged

Issue : Instantiate WMI key mapping only on specific systems only

System : Reebok
Impact : Factory & Customer
Modules : KeyBoard
Authors : robib
Test #1 : Run keyboard.exe on Reebok
Expect : Blacktop key should be displayed as special key when pressed

Issue : HDDUSB 0 size devices failing with divide by 0 error

System : Sawgrass
Impact : Factory & Customer
Authors : rdb
Test #1 : Run "disk -d:hddusb -f:1 -mon"
Expect : All tests should pass

Issue : Missing right bottom screen dialog when run on 15" displays
System : All
Impact : Factory & Customer
Modules : KeyBoard
Authors : robib
Test #1 : Run keyboard.exe on a 15" display
Expect : Keyboard display should include OK and Cancel

Issue : X64 builds not working with WinIPMIDLL on fan, servermgmt, memory
System : All
Impact : Factory
Modules : servermgmt, fan, memory?
Authors : fritzk
Test #1 : servermgmt (X64 version)
Expect : module to identify IPMI devices and run
Test #2 : fan (X64 version)
Expect : module to identify IPMI devices and run

Issue : WinGui screen redraw (or lack thereof) is annoying

System : Any
Impact : Factory & Customer
Authors : marky
Test #1 : winGui
Expect : WinGui window now has a threaded message loop and can redraw the screen
: at all times, wven when running other modules. Much better user
experience.
: Also, module dialogs and/or windows will be set to the front if they
happen
: to come up behind winGui, so the user will always be aware of them. This
: works now even if window/diaglog comes up minimized to taskbar. Fixed ESC
: handling to not intrude on other apps that might be running.

Issue : SEL check fails when H700 has a hot spare on system Sneetch(T610).
Systems : Any with H700 and hot spare
Impact : Factory
Authors : fritzk
Test #1 : Run servermgmt
Expect : no failures due to hot spare.

Issue : Chassis ID for Comiskey was always returing "Unknown"

Systems : Comiskey DT, MT, SFF
Impact : Factory
Authors : carl
Test #1 : Run cables.exe -conf
Expect : SSID to switch to the one for the appropriate chassis. Chassis type to be
correct for
the system being tested (DT, MT, SFF).

Build 6016.7:
-----------------------------------------------------------------------------------
----------------------------------

Issue : DF454772: 6016.6 fails buffer test on H200 with SAS drives
System : Coaster and Diamas
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On a Coaster or Diamas with drives connected to h200 controller run "disk
-f:1 -mon"
Expect : All tests should pass

Issue : Disk fails for -conf if there are no devices found.

System : All
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On a system with no storage devices or add-in controller cards run "disk
-conf"
Expect : Motherboad controller(s) should show up in conf output with no devices
connected.

Issue : GList test on S300 bypassed

System : All with S300
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On a system with S300 and a known HDD with excessive GList entries run
"disk -f:10 -mon"
Expect : Test should fail.

Build 6016.6: Release 2/17/2011

-----------------------------------------------------------------------------------
----------------------------------

Issue : Hitachi drves connected to S300 in RAID mode take very long in DST
System : Coaster with S300 in RAID with Hitachi drives
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On a Coaster with S300 in RAID with Hitachi SAS drives run "disk -f:7 -
mon"
Expect : Test should complete within 2 minutes.

Issue : Seagate HDDs showing up twice in conf

System : Coaster with H200 controller not in RAID and Seagate HDDs
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On a Coaster with H200 controller without RAID and Seagate HDDs run "disk
-conf"
Expect : The Seagate HDDs to only show up under H200 controller

Issue : Added Inspiron One SSID's and Cable support

System : Firestone, Andrews
Impact : Customer & Factory
Modules : Cables
Authors : billb
Test #1 : cables -conf
Expect : All tests should pass

Issue : DF453144 6GBS drives fail on S300

System : Coaster with S300 and 6GBS drives
Impact : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : On a Coaster with S300 and 6Gps drives run "disk -f:1 -mon"
Expect : All tests should pass

Issue : DF453067 S300 with SATA drives fails glist with 6012.2
System : Coaster with S300 and SATA drives
Impact : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : On a Coaster with S300 and 6Gps drives run "disk -f:1 -mon"
Expect : All tests should pass

Issue : DF453077 6012.2 fails buffer test on H200 with RAID

System : Diamas with H200 and 6GBS drives
Impact : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : On a Diamas with H200 and 6Gps drives run "disk -f:1 -mon"
Expect : All tests should pass

Issue : DF453071 Catfish drive represented incorrectly in conf output

System : Coaster with Catfish (RD1000)
Impact : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : On a Coaster with Catfish (RD1000) run "disk -conf"
Expect : RD1000 commodity should be rmd_drive

Issue : Seagate 600GB HDD failing ScsiBuffer test.

System : Diamas with H200 controller
Impact : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : On a Diamas with Seagate 600GB HDD connected to H200 controller run "disk
-f:1 -mon"
Expect : All tests should pass

Issue : S300 driver no longer supports ATA pass through commands

Systems : All systems with S300 and bcraid driver version 2.0.0.0162 or later
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On a system with S300 and bcraid driver version 2.0.0.0162 run "disk -f:1
-mon"
Expect : All test should pass
Test #2 : On a system with S300 and bcraid driver version less than 2.0.0.0162 run
"disk -f:1 -mon"
Expect : All test should pass

Issue : Changed AC Adapter to not show 65 kW Power

Systems : Zuma and other Mini-Inspiron: Sparta, Kenting, etc.
Impact : Customer
Modules : Battery
Authors : billb
Test #1 : Run ePSA
Expect : Health Tab will show AC Adapter as Unknown or n/a

Issue : Updated MH, SG, and PB Cable Support

Systems : Mission Hills, Sawgrass, Palm Beach (MT, DT, SFF)
Impact : Customer
Modules : Cables
Authors : billb
Test #1 : Run ePSA
Expect : Cables Test will pass on X01 or later Motherboard
Test #2 : Run Cables -conf
Expect : Check for cable status change as each cable is unplugged and plugged in

Issue : Removed North Shore ICH Heatsink detection

Systems : North Shore with X02 or later Motherboard
Impact : Customer
Modules : Cables
Authors : billb
Test #1 : Run ePSA
Expect : Cables Test will pass on X02 or later Motherboard

Issue : If PAID bits indicate signal is "blocked", then treat it as an Optional

signal and report just the status.
Systems : all systems with PAID support
Impact : Factory
Modules : cables
Authors : carl
Test #1 : Run EPSA.exe
Expect : Cable tests that have the PAID "blocked" bit set will report the status
instead of a configuration error.

Issue : WinPE video memory test: Fixed problem with PowerEdger server; video
control was not correctly identified.
Systems : Some servers (Problem found on PowerEdge)
Impact : Factory
Modules : Video
Authors : ThomasB
Test #1 : Video
Expect : Should run as normal.

Issue : Added Servermgmt Front Panel LCD test with random strings test
Systems : All systems with front panel LCD
Impact : Factory
Modules : Servermgmt
Authors : fritzk
Test #1 : servermgmt -i
Expect : Pass if screen turns blue, amber, and characters match keyboard input.
Fail if more than 2 retries.

Issue : Modified fan module to support FW change (retries)and shortened fan

string to 25 chars (fix detection).
Systems : All systems with IPMI type fans (PowerEdge, DCS, CE, etc.).
Impact : Factory
Modules : fan
Authors : fritzk
Test #1 : fan -conf
Expect : all fans to be enumerated and listed.
Test #2 : fan
Expect : all fans to be "speed" tested and pass (where hardware is operating
correctly).

Build 6015.8: In Progress

-----------------------------------------------------------------------------------
----------------------------------

Issue : Faield to add tests for the Optical device

Systems : Diamas and Coaster
Impact : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : WinGui
Expect : Confirm that tests show up on Optical device aattached to S100 Controller

Build 6015.7: In Progress

-----------------------------------------------------------------------------------
----------------------------------

Issue : Add SlotId field to output for the S100 Controller

Systems : Diamas and Coaster
Impact : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : disk -conf
Expect : Expect SlotId field to print in for S100 Controller

Build 6015.6:
-----------------------------------------------------------------------------------
----------------------------------

Issue : S100 API changed to no longer show Optical devices as a Physical Device.
: Optical devices are now associated with the S100 using WMI.
Systems : Diamas and Coaster
Impact : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : disk -conf
Expect : Expect CD device to show up under the S100 Controller

Build 6015.5: Release 1/26/2011

-----------------------------------------------------------------------------------
----------------------------------

Issue : By definition of the fan detection interface we should stop on the first
return value of 0xFFFF.
: Some BIOSs have gaps between fan instances which causes the remaining fan
to not be detected. To
: address this we will force a check of all instances between 0 - 6. We
want to limit the # of SMIs
: so if a BIOS has gaps above the first 6 we might need to increase this #.
Systems : Jabba
Impact : Customer & Factory
Modules : Fan
Authors : BryanT
Test #1 : fan
Expect : Should detect all fans.

Issue : Update event log library so users can determine if the log is currently
disabled or if ECC logging is
: currently disabled. Memory tests will need this information since
running tests in this case on ECC
: enabled systems will not allow any correctable errors to be discovered.
IPMI and DMI currently have
: this capability.
Systems : Any
Impact : Customer & Factory
Modules : Eventlog library
Authors : Rods
Test #1 : N/A - Preparation for future memory module enhancements.

Build 6015.4: Release 1/26/2011

-----------------------------------------------------------------------------------
----------------------------------

Issue : Added SB8x0 access class to cables.exe. Added support for the Yalong Bay
system
Systems : Yalong Bay
Impact : Customer & Factory
Modules : cables
Authors : carl
Test #1 : cables -conf
Expect : Output for each cable to show the current status for that cable
detection.

Issue : Keyboard test, when ESC is pressed, can abort subsequent ddusbdiag test
Systems : All
Impact : Customer
Modules : WinGui,TouchPad,Keyboard
Authors : marky
Test #1 : Run winGui and click on Run Tests. Press ESCAPE in Keyboard test, then OK
Expect : USB tests keep running rest of tests, do not stop.

Issue : TBU model showing Dell Power Vault intead of manufacturer's model.
System : Servers with SCSI/SAS TBUs
Impact : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : On a server with SCSI/SAS TBU run "disk -conf"
Expect : TBU should have correct Vendor, Model and FwRev fields plus
ExtendedVendor, ExtendedModel and
: ExtendedFwRev fields with Dell PowerVault information is available.
Issue : Added system AVOCET support in cables.
Systems : Avocet
Impact : Customer & Factory
Modules : cables
Authors : fritzk
Test #1 : cables
Expect : Output should match the original box hardware of a system Yertle.

Build 6015.3: Release 1/14/2011

-----------------------------------------------------------------------------------
----------------------------------

Issue : SCSI TBU SCSI ID does not show up in conf

System : Servers with TBU connected to SCSI controller
Impact : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : On a server with SCSI TCU connected to SCSI controller run "disk -conf"
Expect : TBU to have ControllerPort and slot set to SCSI ID.

Build 6015.2: Release 1/14/2011

-----------------------------------------------------------------------------------
----------------------------------

Issue : DF440330 User has to press OK twice when sequence test is complete
: and he presses ID_OK to exit application
Systems : All with keyboard
Impact : Customer & Factory
Modules : Keyboard
Authors : robib
Test #1 : keyboard -tkbd_sequence -k5
Expect : Press any five keys and then press OK to exit application
: Messagebox with OK should not be displayed

Issue : WinGUI USB drive test taking extremely long time

Systems : Systems with USB HDD
Impact : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : On a system with USB HDD run WinGUI.
Expect : USB drive test to finish within 1 minute.

Issue : Seagate DAT drive not showing up under SCSI controller in conf output
Systems : Servers with Seagate DAT drive connected to LSI SCSI controller
Impact : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : On a server with Seagate DAT drive connected to LSI SCSI controller run
"disk -conf"
Expect : DAT drive to show up under SCSI controller

Issue : Added Cables support for Palm Beach. Updated cables support for Mission
Hills and Sawgrass.
Systems : Palm Beach, Mission Hills, Sawgrass
Impact : Factory
Modules : Cables
Authors : carl
Test #1 : Cables -conf
Expect : Shows status of all cables as defined in the schematics.
Build 6015.1: Release 1/14/2011
-----------------------------------------------------------------------------------
----------------------------------

Issue : Added Cables support for Windu

Systems : Windu
Impact : Factory & Customer
Modules : Cables
Authors : billb
Test #1 : Cables -conf
Expect : Password Jumper in the Not Reset position is require, Touch Panel Cable
is optional

Issue : Kamino with RAID showing RAID array with same drive information
information as HDD0
Systems : Systems with AMD RAID controllers
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On a system with AMD RAID controller with RAID set up run "disk -conf"
Expect : RAID array to show up as a separate with unique drive information under
RAID controller

Issue : Bullion optical device not displaying correct slot information

System : Bullion
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On a Bullion with optical device run "disk -conf"
Expect : Optical device should have correct slot

Issue : Bullion optical device not displaying correct OBIST flags

System : Bullion
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On a Bullion with optical device run "disk -conf"
Expect : Optical device should have correct OBIST flags

Issue : CR431471 : Added ADDS card detection for Jet Li

System : Jet Li
Impact : Factory
Modules : Cables
Authors : carl
Test #1 : cables -conf
Setup : Added output for the state of an ADDS card being installed.
Expect : Status line to indicate ADDS card installed if one is installed. No ADDS
card installed if not installed.

Issue : WinGui collapses nodes when executed by double-clicking mode, but not
from ENTER key or Test Button
System : All
Impact : Customer
Modules : WinGui
Authors : marky
Test #1 : Run wingui and double-click on "USB Root Hub" node of devices.
Expect : After testing complete messageBox is closed, the node should *not*
collapse to [+] state.
Expect : Each device result icon should also display the default "grey" ball state
when the test is
: running. This is for better feedback and some tests do not honor ESC and
will pass so this
: helps to show that and not look like Abort is just not working at all.

Issue : Need to add SystemConfig and BootPath to WinGui

System : All
Impact : Customer
Modules : WinGui
Authors : marky
Test #1 : Run wingui
Expect : New "Order Verification" node appears in left tree-view. Test should pass
if \Dell.sdr
exists and has the new GCF XML information, else test result is "Not
Applicable" and
message "Global Configuration File not found" is printed.
Expect : New "OS Bootpath" device in tree-view and test passes.

Issue : Multi-line error messages are not handled properly in WinGui

System : All
Impact : Customer
Modules : WinGui
Authors : marky
Test #1 : Run wingui memory test in full OS with default
Expect : Expect multi-line error Message: This user does not have rights to lock
pages in memory
: (see
Control_Panel/Administrative_Tools/Local_Security_Policies/Local_Policies/
: User_Rights_Assignment/Lock pages in memory)

Build 6014.3: Release 1/7/2011

-----------------------------------------------------------------------------------
----------------------------------

Issue : TBU connected to LSI SCSI controller does not show under the controller
in conf output
System : All servers
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On a server with tape drive connected to LSI SCSI controller run "disk -
conf"
Expect : TBU to show up under LSI SCSI controller

Issue : Tape drive failing SCSI Confidence test

System : Sneetch and McBean
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On a Sneetch with TBU connected to H200A run "disk -f:2 -mon"
Expect : All tests should pass
Test #1 : On a McBean with TBU connected to H200A run "disk -f:2 -mon"
Expect : All tests should pass

Issue : CR443577 Add support for smbios 2.7.

System : Any with smbios 2.7 supported
Impact : Factory and Customer
Modules : Memory
Authors : rs
Test #1 : Run "memory -conf".
Expect : Examine the output and make sure there are not any unexpected items.

Issue : Added PCI Hardware Dump to conf output.

System : All
Impact : Factory
Modules : Systemconfig
Authors : mikel
Test #1 : Systemconfig -conf
Expect : Should show PCI devices installed.

Issue : DF443987:WBT/FIOF Content Update - Mayzie fails cd test

System : Mayzie with S100
Impact : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : On a Mayzie with optical device connected to an S100 run "disk -d:cdrom -
f:2 -mon"
Expect : Test should pass and eject media

Issue : BTO443940:WBT-FIOF content updated: Zooks TBU test failure

System : Zooks
Impact : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : On a Zooks with TBU connected to H200A run "disk -d:tbu -f:2 -mon"
Expect : Test should pass and eject media

Issue : CR431471: Added ADDS card detection for those platforms that support it.
System : Arrowhead, Azteca, Fleming, Telstra
Impact : Factory
Modules : Cables
Authors : carl
Test #1 : cables -conf
Setup : Added output for the MT and SFF chassis sizes if the card is installed.
Expect : Status line to indicate ADDS card installed if one is installed. No ADDS
card installed if not installed.

Build 6014: Release 12/17/2010

-----------------------------------------------------------------------------------
----------------------------------

Issue : CR431471: Added ADDS card detection for those platforms that support it.
System : All
Impact : Factory
Modules : Cables
Authors : carl
Test #1 : cables -conf
Setup : For Arrowhead DT, Azteca DT, Fleming DT and Telstra DT a line was added
that will show the status of
an add in ADDS2 or ADDS2+ card.
Expect : Status line to indicate ADDS card installed if one is installed. No ADDS
card installed if not installed.

Issue : CR439875: Add Reset option to keyboard menu bar

System : All
Impact : Customer & Factory
Modules : Keyboard
Authors : robib
Test #1 : Keyboard.exe
Setup : Start testing by pressing any key/keys and then select Settings->Reset
Expect : All keys back to initial state

Issue : Add custom keys for Nirvana (WMC,ACP,UCL)

System : Nirvana/Nimoy/Shatner
Impact : Customer & Factory
Modules : Keyboard
Authors : robib
Test #1 : Keyboard.exe
Setup : Select the Custom keys on the top row
Expect : Custom keys should be displayed

Issue : Fix key descriptions for Japanese Layout

System : All with JP Layout
Impact : Customer & Factory
Modules : Keyboard
Authors : robib
Test #1 : Keyboard.exe
Setup : Keyboard.exe -lJP
Expect : Confirm that key positions match keyboard

Issue : Fixed issue where mini layout was counting scans for Numpad
: even though the Numpad keys are not displayed in mini-layout
: (bring up mini-layout in full keyboard with Numpad)
System : All
Impact : Customer & Factory
Modules : Keyboard
Authors : robib
Test #1 : Keyboard.exe
Setup : Start testing by pressing NumPad keys
Expect : Scancount should stay at zero

Issue : Add support for the Eagle and Eagle PC systems. Only support the boards
where SIO GPIO 0x55 is 1.
System : Eagle
Impact : Customer & Factory
Modules : Cables
Authors : carl
Test #1 : cables.exe -conf -xml
Expect : Cables tests are supported.

Issue : Add support for the Chen Long system.

System : Chen Long
Impact : Customer & Factory
Modules : Cables
Authors : carl
Test #1 : cables.exe -conf -xml
Expect : Cables tests are supported.

Issue : Add support for the Teva system.

System : Teva
Impact : Customer & Factory
Modules : Cables
Authors : carl
Test #1 : cables.exe -conf -xml
Expect : Cables tests are supported.
Issue : Video.exe restores the bit level modes so that Python scripts won't show
blank fields.
System : All
Impact : Customer & Factory
Modules : Video
Authors : thomas
Test #1 : Run Python script that creates a small GUI that runs the video test.
Expect : All fields to be visible again after the video test is executed.

Build 6013: Release 12/10/2010

-----------------------------------------------------------------------------------
----------------------------------

Issue : SystemConfig outputing incorrect baseboard information

System : all
Impact : Customer & Factory
Modules : SystemConfig
Authors : rdb
Test #1 : SystemConfig.exe -conf -noexe
Expect : Baseboard device to have correct information

Issue : CR438131: WLAN/WWAN slot verification support in Windows diag

System : all (Especially for Roush-E6400)
Impact : Customer & Factory
Modules : SystemConfig
Authors : mikel
Test #1 : SystemConfig.exe -conf -xml
Expect : Output should show wlan/wwan/wpan for verification.

Issue : Skywalker cables test repeats USB1 and USB2. Should show USB1 to USB4
cable ID
System : Skywalker
Impact : Customer & Factory
Modules : Cables
Authors : carl
Test #1 : cables.exe -conf -xml
Expect : Output should show 4 USB header identifiers.

Issue : Comiskey Disk -conf shows slot 0 for all devices

System : Comiskey
Impact : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : On a Comiskey with HDD and ODD devices run "disk -conf"
Expect : Slot number for each device should be correct.

Issue : Updated North Shore Cables for X01 Hardware

System : North Shore
Impact : Customer & Factory
Modules : Cables
Authors : billb
Test #1 : cables.exe
Expect : Test should pass and show the type of the Center Riser
Test #2 : cables -conf
Expect : Check installed and not installed status as each cable is plugged in or
unplugged

Issue : Added BSLSAN Cable support

System : Big Sur, Little Sur, Negril
Impact : Customer & Factory
Modules : Cables
Authors : billb
Test #1 : cables.exe
Expect : Test should pass
Test #2 : cables -conf
Expect : Check installed and not installed status as each cable is plugged in or
unplugged

Issue : Hotshot stuck in infinite loop

System : Hotshot
Impact : Customer & Factory
Modules : SystemConfig
Authors : rdb
Test #1 : On a Hotshot with multiple processors run "SystemConfig -conf -noexe"
Expect : System should display Baseboad, CPU, PCI and USB device configuration
information

Issue : DF437037 R-Win key not on keyboard but still displayed

Systems : All
Impact : Customer & Factory
Modules : KeyBoard
Authors : robib
Test #1 : run command : keyboard.exe
Expect : R-Win key will be displayed in light-Cyan and Basic Help specifies
Expect : that this color key may be optional

Issue : User should be warned of stuck keys

Systems : All
Impact : Customer & Factory
Modules : KeyBoard
Authors : robib
Test #1 : run command : keyboard.exe
Setup : Test key but do not release
Expect : Warning MessageBox to display that key maybe stuck

Issue : BR NumPad keyboard does not recognize key with scan code 0x7e
Systems : Systems with BR Numpad keyboard
Impact : Customer & Factory
Modules : KeyBoard
Authors : robib
Test #1 : run command : keyboard.exe -lBR -numpad
Setup : System with BR Numpad Keyboard (Krug)
Expect : System should display and recognize extra "." Key

Issue : Horton failing DST Long with SMART Command Failure

Systems : Horton
Impact : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : On a Horton run "disk -f:8 -mon"
Expect : System should pass DST Long.

Issue : Katsiki with RAID and with multiple optical devices not being associated
with a controller and
: not having correct OBIST field entries.
Systems : Katsiki
Impact : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : On a Katsiki with RAID and multiple optical devices run "disk -conf"
Expect : Optical devices should be associated with a controller and OBIST field
entries should be correct.

Issue : Mayzie with SAS6I/R and with Catfish connected to MB SATA in AHCI mode
fails with exception error.
Systems : Mayzie
Impact : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : On a Mayzie with SAS6I/R and with a Catfish connected to MB SATA in AHCI
mode run "disk -conf"
Expect : System should pass without exception error and Catfish (RD1000) should
show up as RMD device
: associated with the onboard controller.

Issue : DF428071: Drive Interface on S300 changes when RAID mode changes
Systems : Horton
Impact : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : On a HORTON with SATA drives connected to S300 in Non-RAID run "disk -
conf"
Expect : Drive interface should be SERIAL
Test #2 : On a HORTON with SATA drives connected to S300 in RAID run "disk -conf"
Expect : Drive interface should be SERIAL

Issue : DF426260 [SSI] HDDUSB0 failed when run Dell Diag 6010
Systems : All with Multi-Card USB device
Impact : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : On a system with internal Multi-Card run "disk -conf"
: Locate device name for Multi-Card device.
: Run "Wingui"
: Select Multi-Card device and click "Run Tests"
Expect : Test should pass with "No test available for this device" message.

Issue : DF435097 N13:Memory Error when run WBT

Systems : All
Impact : Customer & Factory
Modules : Memory
Authors : bbw
Test #1 : Run memory.exe on full OS Windows
Expect : Test will still fail, but indicate the local security policy to change

Issue : Add DIMM isolation information to memory test

Systems : Client systems
Impact : Customer & Factory
Modules : Memory/DDDriver
Authors : bbw
Test #1 : Run memory on system with bad DIMM that is in list of MpMemory
: supported HW for DIMM isolation (Arrowhead/Deimos/...)
Expect : DIMM ISOLATION message when memory compare error found.

Build 6012 Released 11/24/2010

-----------------------------------------------------------------------------------
----------------------------------
Issue : DF434418:Disk.exe failed to get disk info when SSD HDD is installed on
Reebok
Systems : All with Samsung SSD
Impacy : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : On a system with Samsung 2.5" SSD run "disk -conf"
Expect : Drive information for SSD should be displayed.

Issue : CR430964:Add Webcam Resolution in Output.

Systems : All notebooks with Webcam
Impact : Customer & Factory
Modules : DDUSBDiag
Authors : ea
Test #1 : On a notebook with an integrated Webcam run �DDUSBDiag �conf?
Expect : USBISTDev entry should be in output.

Issue : KeyBoard and TouchPad now use common SMBios routines to determine
: running on NoteBook or Desktop
System : All
Impact : Factory & Customer
Modules : KeyBoard & TouchPad
Authors : robib
Test #1 : Using WinGUI run KeyBoard on Desktop system
Expect : WinGUI should display "Attached KeyBoard"
Test #2 : Using WinGUI run KeyBoard on NoteBook system
Expect : WinGUI should display "Embedded KeyBoard"
Test #1 : Using WinGUI run TouchPad on Desktop system
Expect : WinGUI should not display any TouchPad device

Issue : Horton not showing Optical device on correct connector when in AHCI mode
System : Horton
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On a Horton in AHCI mode run "disk -conf"
Expect : Optical device should show up on correct connector

Issue : TBU device not displaying controller port or slot number in conf output.
System : Servers with TBU connected to a PERC or SAS controller
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On a server with TBU connected to a PERC or SAS controller run "disk -
conf"
Expect : Slot and port information should be displayed for TBU

Issue : DF422916,DF431455:Systems using AMD AHCI controller in RAID mode do not

display drives correctly
System : All systems that have AMD AHCI controllers with RAID
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On an AMD system with less than 4GB of memory in RAID mode run "disk -
conf"
Expect : All drives should be displayed with the correct configuration
information.
Test #2 : On an AMD system with 4GB of memory or greater in RAID mode run "disk -
conf"
Expect : Drive information will not be displayed.

Issue : DF431317:Wrong CPU name string on Green platform

Systems : Green
Impact : Customer & Factory
Modules : SystemConfig
Authors : rdb
Test #1 : On a Green platform run "SystemConfig -conf -d:CPU"
Expect : Correct CPU name string in output.

Issue : Link to SMBIOS api in TouchPad module to determine if NoteBook system

Systems : All Notebooks and Desktops
Impact : Customer & Factory
Modules : TouchPad
Authors : robibb
Test #1 : Run "TouchPad -conf -xml -o:device.xml" on a desktop
Expect : TouchPad moudle should not run. device.xml should have device not
supported
Test #1 : Run "WinGui" on a desktop
Expect : TouchPad module should not get instantiated.

Issue : Added Cable Support for Mission Hills and Sawgrass

Systems : Mission Hills,Sawgrass
Impact : Customer & Factory
Modules : Cables
Authors : billb
Test #1 : cables
Expect : Pass if all required cables are installed. Installed status changes as
each cable, etc. is removed.

Issue : Added CPU Model, Type and Stepping to CPU conf output
Systems : All
Impact : Customer & Factory
Modules : SystemConfig
Authors : rdb
Test #1 : run "SystemConfig -conf -d:CPU"
Expect : ProcessorIDType, ProcessorIDModel and ProcessorIDStepping fields should
have valid data

Issue : Added FTB15 (Sequential Read Test of the entire drive) to disk.
Systems : All
Impact : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : Run "disk -f:15 -mon -t:60"
Expect : Test should stop after 60 seconds with no errors
Test #2 : Run "disk -f:15 -mon"
Expect : Test should do a surface scan of the entire disk with no errors.

Issue : Added BR Layout changes to keyboard

: DF430069: Missing Enter NumPad key in UK Layout
: Mini keyboard layout cleanup
Systems : portables
Modules : KeyBoard
Authors : robi
Test #1 : Keyboard -lBR
: setup: need Brazilian Layout keyboard
Expect : Brazilian layout should display and Pass
Issue : Added NVidia /3D(EDP) panel controller num (0xB) for Voyager.
Systems : portables
Impact : BIOS
Modules : NBPanel
Authors : mikel
Test #1 : NBPanel.
Expect : The NBPanel should pass on all Voyager configs.

Issue : Add mini keyboard layout (w/o Numpad) for small screen systems like
: Welch, Samos etc
Systems : Welch, Samos
Impact : Factory & Customer
Modules : keyboard
Authors : robib
Test #1 : On a Welch or Samos run the comamnd "KeyBoard -mini"
Expect : Layout should display with OK and Cancel buttons on screen

Issue : Horton in RAID mode not showing Optical device under the correct
controller
Systems : Horton
Impact : Factory & Customer
Modules : disk
Authors : rdb
Test #1 : On a Horton in RAID mode with an optical device run "disk -conf"
Expect : All devices should show up under the correct controller
Test #2 : On a Horton in RAID mode with an optical device run "disk -d:cdrom -f:2"
Expect : Test should pass

Issue : Horton in AHCI mode not showing devices under the correct controller
Systems : Horton
Impact : Factory & Customer
Modules : disk
Authors : rdb
Test #1 : On a Horton in AHCI mode run "disk -conf"
Expect : All devices should show up under the correct controller

Issue : DF426526 : SubVendorId and SubDeviceId swapped for Intel RAID Controller
Systems : Alienware Laptop
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On an Alienware Laptop run "disk -conf"
Expect : Intel Controller SubVendorId and SubDeviceId should be correct.

Issue : DF425070 Fails on BIOS/Diag call 0x52 0x09 read inverter type. Added
fIsBiosSWSmiFunctionSupported for ReadInverterType.
Systems : Portables
Impact : Factory & Customer
Modules : nbpanel
Authors : mikel
Test #1 : nbpanel.exe -v
Expect : If bios supports the function, the test should pass. Otherwise, the test
should not run.

Issue : ATA device interface defaulting to IDE.

Systems : All systems
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On a system with SATA devices run "disk -conf"
Expect : Devices should have Serial interface unless connected to a 40 pin
parallel connector

Issue : TBU device connected to H200 has interface value of SCSI

Systems : All that have TBU connected to H200
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On a system with TBU connected to H200 run "disk -conf"
Expect : TBU interface should show as SAS

Issue : DF426051/DF426029 WinPE Delldiag(WinGui) ODD test fail and DF426260

HDDUSB0 failed
Systems : All
Impact : Customer only
Modules : WinGui
Authors : marky
Test #1 : Wingui
Expect : Expect normal operation, no illegal -f:{n) parmeters passed to various
modules

Issue : Update sensors to include an uninitialized state. For Windows, these

will just
: read as 0.
Systems : All
Impact : Factory & Customer
Modules : Battery, Fan, SystemManagement
Authors : rods
Test #1 : Run as normal.
Expect : For Windows, there should be no noticable change.

Issue : Add support for PE M915 (Squeeze) in the Cables test.

Systems : Squeeze
Impact : Factory & Customer
Modules : cables
Authors : bbw
Test #1 : Run with -conf.
Expect : Should output signals for the Squeeze system.

Issue : WinGui traps ESC and Video does not output progress, so abort does not
work
Systems : All
Impact : Customer only
Modules : WinGui
Authors : marky
Test #1 : wingui video.exe
Expect : Press ESC after starting the video testing and verify testin stops
shortly.

Build 6011 Released Oct 14, 2010

-----------------------------------------------------------------------------------
----------------------------------

Issue : Optical devices connected to S100 failing cdread test

Systems : Mayzie
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On a system with an optical drive connected to an S100 run "disk -d:cdrom
-f:2"
Expect : Test should pass.

Issue : Virtual CDROM devices failing when running cd tests

Systems : Bullion
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On a Bullion with an optical drive connected to the onboard controller
run "disk -d:cdrom -f:2"
Expect : Test should pass.

Issue : SSD devices showing up twice in conf output

Systems : Zooks
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On a system with SSD devices connected to H200I run "disk -conf"
Expect : SSD drives should only show up under the H200I controller

Issue : SSDs failing GList test

Systems : Zooks
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On a systems with SSD drives run "disk -f:10 -mon"
Expect : All devices should pass.

Issue : Cables test output displayed all signals. Now it displays just the
failing signals.
: Use the -conf output to see the full list of signals.
Systems : All
Impact : Factory & Customer
Modules : Cables
Authors : carl
Test #1 : Run Cables.exe
Expect : If a Required cable is not present, just the error message for that
cable.

Issue : SCSI Devices not showing up under controller

Systems : Bullion
Impact : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : On a Bullion with devices connectd to the on board controller run "disk -
conf"
Expect : On board controller should have devices under it

Issue : CDREAD test failing on systems with Optical device connected to S100 port
Systems : Any system with optical device connected to S100 port
Impact : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : On a system with S100 connect an optical device and run "disk -d:cdrom -
f:1"
Expect : System should pass
Issue : Systems with 2TB drives connected to PERC 6/i read negative capacity
Systems : Systems with 2TB drives connected to PERC 6/i
Impact : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : On a system with PERC 6/i connect 2TB drives and run "disk -conf"
Expect : Drives should have correct capacity

Issue : Optical devices connected to H200 did not show up under the controller
Systems : Any with optical device connected to H200
Impact : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : On a system with optical device connected to an H200 run "disk -conf"
Expect : Optical device should show up under H200

Issue : McBean with multiple PERC controllers were not displaying all controllers
Systems : McBean
Impact : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : On a McBean with Multiple PERC controllers run "disk -conf"
Expect : All controllers should be displayed with connected devices under them.

Issue : KeyBoard multi-media buttons now in color

: Added Blacktop and AWWC key for Voyager
Systems : Portables
Impact : Customer & Factory
Modules : Keyboard
Authors : rsb
Test #1 : Run the comamnd Keyboard -multi from the command line
Expect : Multi-medis should display in color

Issue : TBU connected to H200 not showing up under the controller in conf output
Systems : All systems with H200 and TBU devices
Impact : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : On a system with an H200 with a TBU connected to it run "disk -conf"
Expect : Output should show TBU device under the H200 controller.

Issue : Added Adaptec controller discovery

Systems : All systems with Adaptec SCSI controller
Impact : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : On a system with an Adaptec SCSI controller with a TBU connected to it
run "disk -conf"
Expect : Output should show an entry for the controller and the TBU device should
be under the Adaptec controller.

Issue : (DF423076)Wocket and Fat Tire 32 internal controllers showing up as

external in conf output
Systems : Wocket and Fat Tire 32
Impact : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : On a Wocket run "disk -conf"
Expect : PERC Controller should have ControllerInOrExt as Internal.
Test #2 : On a Fat Tire 32 run "disk -conf"
Expect : IDE Controller should have ControllerInOrExt as Internal.

Issue : RD1000 not displaying in conf

Systems : Servers with RD1000
Impact : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : On a system with RD1000 run "disk -conf"
Expect : RD1000 should show up in ouput as type RMD

Issue : Devices connected to IDE/ATA/SATA controllers not displaying correct port

numbers.
Systems : All
Impact : Customer & Factory
Modules : Disk
Authors : rdb
Test #1 : On a system with multiple devices connected to on board SATA ports run
"disk -conf"
Expect : Devices should be displayed under the controller with the correct on
board connector in the slot field.

Issue : Update the eventlog scan for client diagnostic log to allow it to capture
new events.
Systems : All
Impact : Factory and Customer
Modules : Eventlog
Authors : rs
Test #1 : Run "eventlog" as normal.
Expect : For Windows, there is no real change since none of the modules currently
write to the diag log. But since
: the code is in a library, it affects the Windows module. The visible
change is in PSA.

Issue : Correct formatting year in Client BIOS log. Remove the temperatures from
the power events since those are
: really for bios debug use. Update the output of the Diag log to remove
the excess field separators.
Systems : All
Impact : Factory and Customer
Modules : Eventlog
Authors : rs
Test #1 : Run "eventlog -dump".
Expect : The timestamp in the logs should have the correct year. For the diag log
entries, they are now formatted
: to remove the extra field tags since those made it less readable. The
updated format is as follows:
: "<Pass|Fail> <Program> V<version> Error <code:code>. [Message]
[FRU=<fru>] [PPID=<ppid>]"

Issue : Break out timestamp into separate field in event log.

Systems : All
Impact : Factory and Customer
Modules : Memory, SystemManagement, EvLog
Authors : rs
Test #1 : Run as normal.
Expect : The only difference should be in the output where the timestamp field is
given separately if the logs
 : contain any events that are selected for formatting.

Issue : Added cables support for North Shore

Systems : North Shore
Impact : Factory
Modules : Cables
Authors : billb, carl
Test #1 : cables
Expect : Pass if all required cables are installed. Installed status changes as
each cable, etc. is removed.

Issue : Added Intrusion Switch State support

Systems : Katsiki, North Shore
Impact : Factory
Modules : Cables
Authors : carl, billb
Test #1 : cables
Expect : No Intrusion if powered up with instrusion switch plunger pushed in.
Intrusion if plunger out when cables is run.

Issue : Cables needs support for not installed to be a message on some signals
that require the "cable" be not
: installed.
Systems : All with cables support
Impact : Factory
Modules : cables
Authors : fritzk
Test #1 : Run "cables"
Expect : System that is correctly "wired/cabled" should now pass and show not
installed on NVRAM CLEAR JUMPER.
Test #2 : Review output.
Expect : Verify that signals are correct for the given system; use 6010 to
compare, make sure NVRAM says not
: installed.

Issue : Support for system DERBY, R310 storage solution with new system id.
Systems : Derby
Impact : Factory
Modules : Cables
Authors : fritzk
Test #1 : Run cables on system Derby
Expect : signals should be the same as the ones on R310 (Sam_I_am).

Issue : Add support for Touchpad in WinGui

Systems : Any notebook
Impact : Factory
Modules : WinGui
Authors : marky
Test #1 : wingui touchpad
Expect : Test passes, ESC works, close box and ALT=F Exit work properly, too.

Build 6010:
-----------------------------------------------------------------------------------
----------------------------------

Issue : FDD not recognizing floppy has been removed.

Systems : All
Impact : Factory and Customer
Modules : Disk
Authors : rdb
Test #1 : run "disk -d:FDD -f:2"
Expect : Operator should be prompted to insert floppy and then to remove floppy.
Test should pass.

Issue : Not all optical devices are recognized

Systems : All
Impact : Factory and Customer
Modules : Disk
Authors : rdb & billb
Test #1 : On a system with DVD Combo drive run "disk -conf"
Expect : Optical device should show up in output

Issue : Systems with AMD ahci drivers failing IDE_DIAG

System : All
Impact : Factory and Customer
Modules : Disk
Authors : rdb & billb
Test #1 : On a system with AMD RAID enabled run "disk -d:CDROM -f:1"
Expect : Test should pass

Issue : PERC and SAS controller ports/slots not correct for systems with a Back
Panel.
Systems : Servers with PERC/SAS and Back Panel
Impact : Factory & Customer
Modules : Disk
Authors : rdb
Test #1 : On a server with a PERC or SAS controller and drives connected to a Back
Panel run
"disk -conf"
Expect : Slot number to contain the correct slot for the disks.

Issue : Added the ability to find a PCI device by it's VID:DID or by it's class
code.
Added the ability to find all devices in the system using the PCI address
(tag).
Added output in SystemConfig for all PCI devices found in the system.
Systems : All
Impact : Factory & Customer
Modules : SystemConfig
Authors : carl
Test #1 : run "SystemConfig -conf -xml"
Expect : Output at the end of the list will show all PCI devices by their hardware
tag,
vendor ID and device ID. I would suggest using the Description field as
information
only. I am still adding to the decoding of the class code values, so
strings are
going to change over time.

Issue : Keyboard enhancement makes buttons Owner Draw for color changes
Systems : All
Impact : Factory
Modules : KeyBoard
Authors : rsb
Test #1 : run KeyBoard.exe
Expect : Keys should display in Cyan and change to Magenta
Issue : Fixes -d: in combination with -conf issue in SystemConfig
Systems : All
Impact : Factory & Customer
Modules : SystemConfig
Authors : rdb
Test #1 : run "SystemConfig -d:CPU -conf -xml"
Expect : Test should only CPU configuration information

Issue : Fixes hang on ComisKey when battery.exe or sysman.exe are run.

Systems : ComisKey
Impact : Factory & Customer
Modules : Sysman & Battery
Authors : bjt
Test #1 : Sysman.exe
Expect : Test should return NA.
Test #2 : Battery.exe
Expect : Test should return NA.

Issue : Fixed exception when using WMIEvent class for multi-media Eject key
Systems : Paltrow
Impact : Factory & Customer
Modules : KeyBoard
Authors : rsb
Test #1 : KeyBoard.exe -multi
Expect : Eject key should change state when pressed and no exception on exit
Test #2 : KeyBoard.exe ( Select Settings->Display multi-media keys)
Expect : Eject key should change state when pressed and no exception on exit

Issue : Added cd read functional blocks with media checking

System : All
Impact : Factory & Customer
Modules : Disk
Authors : billb
Test #1 : run "disk -d:cdrom -f:1"
Expect : Test should pass with a CD or DVD re-install
Test #2 : run "disk -d:cdrom -f:2"
Expect : Test should pass with a CD or DVD re-install
: User prompt for media different with an Audio CD
Test #3 : run "disk -d:cdrom -f:3"
Expect : Test should pass with a CD or DVD re-install
: User prompt for media different with an Audio CD

Issue : Initial release of Touchpad and PointStick

Systems : all
Impact : Factory & Customer
Modules : TouchPad
Authors : rsb
Test #1 : TouchPad
Expect : Follow instructions on screen for Touchpad
Test #2 : TouchPad -pstick
Expect : Follow instructions on screen for PointStick

Issue : Modified HDD write/read test to only perform a read if HDD has partitions
System : All
Impact : Factory & Customer
Modules : Disk
Authors : rb
Test #1 : run "disk -f:14 -mon"
Expect : Test should pass.
Issue : Ambient thermistor not recognized by Systems Management
System : Wembley
Impact : Factory & Customer
Modules : sysman
Authors : vm
Test #1 : sysman
Expect : Test should pass.

Issue : Change sysman to group thermal sensors under a single device.

Systems : All
Impact : Factory & Customer
Modules : SysMan
Authors : rs
Test #1 : Run "sysman -conf -xml"
Expect : The output should show the same sensors, just grouped under a single
device.

Issue : Adds a switch to exclude USB BIST tests.

Systems : All
Impact : Factory & Customer
Modules : DDUsbDiag
Authors : rs
Test #1 : Run "DDUsbDiag -skiptest1"
Expect : Verify that the first USB BIST test is not run on all UBIST devices.
(Repeat this for the remaining tests)

Issue : Keyboard.exe does not create output file on different drive

: always in default module directory
Systems : all
Impact : Factory & Customer
Modules : keyboard
Authors : rsb
Test #1 : keyboard.exe -conf -o:e:\output.txt
Expect : should create output.txt on e: drive
Test #2 : keyboard.exe -conf -o:e:\output.txt -xml
Expect : should create output.xml on e: drive

Issue : Added FDD support to Disk

Systems : All
Impact : Factory & Customer
Modules : Disk
Authors : rb
Test #1 : On a system with a floppy drive run "disk -d:FDD -f:1 -mon"
Expect : Test should pass
Test #2 : On a system without a floppy drive run "disk -d:FDD -f:1 -mon"
Expect : Test should fail
Test #3 : On a system with a floppy drive run "disk -d:FDD -f:2 -mon"
Expect : Operator should be prompted to insert media into FDD and then prompted to
remove it. Test should pass.

Issue : Added Build Verification to SystemConfig

Systems : All
Impact : Factory & Customer
Modules : SystemConfig
Authors : rb
Test #1 : On a system that has a valid GCF file for that specific system run
"SystemConfig -bv -gcf:<GCF file>
Expect : Build Verification should pass if all parts in the system match the GCF
file.

Issue : TBU non interactive tests

Systems : All
Impact : Factory & Customer
Modules : Disk
Authors : rb
Test #1 : On system with tape drive, remove any media in TBU and run "disk -f:1 -
mon -ix -d:TBU"
Expect : System to pass with no operator prompts
Test #2 : On same system run "disk -f:1 -mon -d:TBU"
Expect : Operator prompts to add media. System to pass when media inserted. Media
will eject at end of test.

Issue : Wiseman - fan speed takes time to settle down below maximum speed
Systems : All
Impact : Factory & Customer
Modules : Fan
Authors : vm
Test #1 : Run fan test
Expect : Test to pass

Issue : Get inverter type function call failed

Systems : Poitier
Impact : Factory & Customer
Modules : nbpanel
Authors : vm
Test #1 : Run nbpanel test
Expect : Test to pass

Issue : Nbpanel runs on desktop systems

Systems : Turnberry
Impact : Factory & Customer
Modules : nbpanel
Authors : vm
Test #1 : Run nbpanel test
Expect : No devices found

Issue : Ntrig exposes a USB BIST descriptor but doesn't support UBIST, excluded
support for this device.
Systems : All
Impact : Factory & Customer
Modules : DDUSBDIAG
Authors : bt
Test #1 : Run DDUSBDIAG on Ntrig USB devices.
Expect : Test should pass

Issue : BackPanel output to conf

Systems : Servers with back panels
Impact : Factory & Customer
Authors : rb
Test #1 : On a system with a back panel run "disk -conf"
Expect : Conf output will have Back panel product id, vendor and firmware revision
information.

Issue : Added support for QT MDiags effort.

Systems : Oriole_eql, Skipper, Slinky, McBean, SamIam,
 : Terrapin, Sneetch, and CindyLou.
Impact : Factory and Customer
Modules : cables
Authors : fritzk
Test #1 : Run cables -conf
Expect : current status of all signals monitored, no pass/fail
Test #2 : Run cables
Expect : module status of pass/fail depending on if the required signals where set
accordingly.

Build 6009:
-----------------------------------------------------------------------------------
----------------------------------

Issue : SAS6 I/R failing SMART in GList test

Systems : Horton
Impact : Factory and Customer
Modules : Disk
Authors : rb
Test #1 : On horton with SAS6 I/R controller and SATA hard drives run "disk -f:10"
Expect : System should pass.

Issue : S300 failing Verify test with memory error

Systems : Horton
Impact : Factory and Customer
Modules : Disk
Authors : rb
Test #1 : On horton with S300 controller run "disk -f:1 -mon"
Expect : System should pass.

Issue : Optical devices showing up multiple times in -conf output

Systems : All
Impact : Factory and Customer
Modules : Disk
Authors : rb
Test #1 : On a system with multiple optical devices run "disk -conf"
Expect : Only one entry for each optical device. Devices should be displayed under
the controller it is connected to.

Issue : On-board ATA/SATA controller port count staying at 0

Systems : All
Impact : Factory and Customer
Modules : Disk
Authors : rb
Test #1 : On a system with drives connected to on-board ATA/SATA controller run
"disk -conf"
Expect : Controller port count should be greater than 0 for any controller with
drives connected to it.

Issue : WinGui is being used by ODM's

Systems : Any
Impact : Factory & Customer
Modules : WinGui
Authors : marky
Test #1 : Run 'start /w winGui'
Expect : Expect errorlevel to be 0 only if all tests are run successfully
Test #2 : Edit wingui.ini and add line 'keyboard.exe skip"
Expect : Expect keyboard.exe to be ignored, no device or test run. Warning message
is only indication
 : of "skip" in wingui CONSOLE window and wingui.txt output.

Issue : Remove factory only strings. Note that previous changes kept these
strings from being shown to the user,
: this change physically removes them from the object.
Systems : Any
Impact : Customer
Modules : ServerMgmt
Authors : rs
Test #1 : Run "servermgmt -?"
Expect : The output should not contain the strings for clearing the SEL, rebooting
the iDrac, etc.

Issue : Added support for fan overspeed test.

Systems : Any
Impact : Factory & Customer
Modules : fan
Authors : vm
Test #1 : Run "fan"
Expect : The fan module should run the overspeed test if applicable.

Issue : Added support for cable detection on Turnberry and Riviera

Systems : Turnberry, Riviera
Impact : Factory
Modules : Cables
Authors : carl
Test #1 : cables.exe
Expect : Test to pass if all Required cables are properly installed. Test to fail
if one or more
Required cables are not installed. User must parse output to determine
correct status
for Optional cables.

Issue : Add dumping FRU information from IPMI agents.

Systems : Any IPMI
Impact : Factory & Customer
Modules : ServerMgmt
Authors : rs
Test #1 : Run "servermgmt -FruDump" on an IPMI system.
Expect : The test should locate all FRUs and format the data in them.

Issue : Add "Commodity" tag to each DIMM instance in memory config

Systems : Any
Impact : Factory & Customer
Modules : Memory
Authors : rs
Test #1 : Run "memory -conf".
Expect : The output should include the new line showing the commodity as
"system_memory_module".

Issue : AMD Driver causing ATA Identify Device failure

Systems : Any system with AMD Chip Set with amdsata driver version 1.2.001.xxx
Impact : Factory & Customer
Modules : Disk
Authors : rb
Test #1 : On a system with AMD Chip Set with amdsata driver version 1.2.001.001 or
greater run
: "disk -conf"
Expect : All hard drives should have a valid conf entry.
Issue : Turnberry assert error with SystemConfig
Systems : Any
Impact : Factory & Customer
Modules : SystemConfig
Authors : rb
Test #1 : On a system with no ppid in smbios run "SystemConfig -noExe"
Expect : Valid conf output

Issue : Drives connected to AMD controller not showing up under controller in

conf output
Systems : All systems with AMD chip set
Impact : Factory & Customer
Modules : Disk
Authors : rb
Test #1 : On a system with AMD chip set run "disk -conf"
Expect : All hard drives connected to AMD controller should show up under
controller

Issue : Added -t:[N] switch to disk to put a time cap on tests that are not
already time capped
Systems : All
Impact : Factory & Customer
Modules : Disk
Authors : rb
Test #1 : run "disk -f:8 -mon -t:30"
Expect : DST Long should start and test should end in 30 seconds.

Issue : Added line switches for displaying numpad and multi-media from cmdline
Issue : WInPE 64-bit image does not display full keyboard fix
Systems : All
Impact : Factory & Customer
Modules : Keyboard
Authors : robi
Test #1 : run "keyboard.exe -numpad -multi" in WinPE 64-bit
Expect : Should display full keyboard incl numpad and multi-media keys

Build 6008:
-----------------------------------------------------------------------------------
----------------------------------

Issue : Horton failed with "Unable to access memory".

Systems : Horton
Impact : Factory & Customer
Modules : Disk
Authors : rb
Test #1 : On a Horton run "Disk -conf"
Expect : System configuration shold be displayed without errors.

Issue : On 64 Bit build Disk failed with "Unable to access memory".

Systems : All
Impact : Factory & Customer
Modules : Disk
Authors : rb
Test #1 : On a 64 Bit Windows system run "Disk -conf"
Expect : System configuration shold be displayed without errors.

Issue : On customer builds the diags did not fail if no battery was installed.
Systems : All
Impact :
Factory & Customer
Modules :
Battery
Authors :
bt
Test #1 :
Verify that all desktop systems do not fail this test. On desktops the
test should report "No devices Detected". Run "battery ".
Test #2 : Verify that all notebook systems do not fail this test. On notebooks the

test should pass. Run "battery ".

Test #3 : On all notebooks systems power off the system then uninstall all
batteries.
Power on the system and run the battery test, the test should fail with
"No battery is installed". Run "battery" at the command line. While the
system is still running, insert the battery and rerun the test. The test
should now pass. While the system is still running remove the battery and

rerun the test. The test should fail this time.

Expect : System should pass.

Issue : Enabled SMART for GList test due to Horton with S300 failing SMART Read
Data.
Systems : Horton
Impact : Factory & Customer
Modules : Disk
Authors : rb
Test #1 : On a Horton with ATA drives connected to an S300 run "Disk -f:1 -mon"
Expect : System should pass.

Issue : CR383369 - Updated ZeroDrive to zero entire drive when -full switch is
used. If it is not used will still
only zero 1st and last gigabyte of drive. This switch is only available
for FACTORY Win32 and x64 releases.
Systems : All
Impact : Factory
Modules : Disk
Authors : rb
Test #1 : On a system where it does not matter if all the hard drives are wiped out
run "Disk -ZeroDisk -full"
Expect : Operator prompt and complete zeroing of all hard drives in the system

Issue : Added AC Adapter power information test.

Systems : Reebok
Impact : Factory & Customer
Modules : Battery
Authors : Vinod
Test #1 : Run "Battery -ix"
Expect : AC Adapter power should be displayed.

Issue : Added IEEE1394 test.

Systems : Reebok
Impact : Factory & Customer
Modules : IEEE1394
Authors : ml
Test #1 : Run "IEEE1394"
Expect : Test should execute correctly.
Issue : Added more information on charge test failure.
Systems : Reebok
Impact : Factory & Customer
Modules : Sysman
Authors : Vinod
Test #1 : Run "sysman" with a battery that is not fully charged. Press Ctrl-C
immediately after sysman starts to simulate an error.
Expect : The error message should display "Expected Charge", "Current Charge", "AC
Adapter Power", "Battery Health" and "Battery Charge Cycles".

Issue : Added ATA/SATA controller with connected devices to conf output.

Systems : Any with a Hard Drive connected to ATA/SATA controller
Impact : Factory & Customer
Modules : Disk
Authors : rb
Test #1 : On a system that has a hard drive connected to an ATA or SATA controller
run "Disk -conf"
Expect : Controller information should be displayed and disks connected will be
display under controller
entry.

Issue : Added -MediaEject switch

Systems : Any with removal Optical or Tape media
Impact : Factory & Customer
Modules : Disk
Authors : rb
Test #1 : On a system with optical media installed in device run "Disk -d:CDROM -
MediaEject"
Expect : optical drive tray should open to eject media.
Test #2 : On a system with tape installed in TBU device run "Disk -d:TBU -
MediaEject"
Expect : Tape should eject from TBU

Issue : Added -MediaLoad switch

Systems : Any with removal Optical or Tape media
Impact : Factory & Customer
Modules : Disk
Authors : rb
Test #1 : On a system with open optical media open tray run "Disk -d:CDROM -
MediaLoad"
Expect : optical drive tray should close.
Test #2 : On a system with TBU device put tape in drive and run "Disk -d:TBU -
MediaLoad"
Expect : Tape should load into TBU

Issue : Added -MediaPresence switch

Systems : Any with removal Optical or Tape media
Impact : Factory & Customer
Modules : Disk
Authors : rb
Test #1 : On a system with optical media installed in device run "Disk -d:CDROM -
MediaPresence"
Expect : Output should display media is installed with status of pass.
Test #2 : On a system without optical media installed in device run "Disk -d:CDROM
-MediaPresence"
Expect : Output should display media is not installed with status of fail.
Test #3 : On a system with tape installed in TBU device run "Disk -d:TBU -
MediaPresence"
Expect : Output should display media is installed with status of pass
Test #4 : On a system without tape installed in TBU device run "Disk -d:TBU -
MediaPresence"
Expect : Output should display media is not installed with status of fail

Issue : Multiple entries for the same optical device in -conf outputfor an
optical device
connected to an S100 controller
Systems : Any with an optical device connected to S100 controller
Impact : Factory & Customer
Modules : Disk
Authors : rb
Test #1 : On a system that has an optical device connected to an S100 controller
run "Disk -conf"
Expect : optical device should only show up 1x under S100 Controller

Issue : RAID array on S100 controller having CDROM mnemonic

Systems : Any with a RAID setup on an S100 controller
Impact : Factory & Customer
Modules : Disk
Authors : rb
Test #1 : On a system that has an S100 controller with RAID configured run "Disk -
conf"
Expect : All HDD entries for the RAID should not have a CDROM mnemonic

Issue : RAID array on S100 controller having controller as an element of the

array
Systems : Any with a RAID setup on an S100 controller
Impact : Factory & Customer
Modules : Disk
Authors : rb
Test #1 : On a system that has an S100 controller with RAID configured run "Disk -
conf"
Expect : All array entries under the S100 controller should have HDDx entries for
PD_x_DeviceName

Issue : Added ControllerInOrExt field to controller conf output

Systems : All
Impact : Factory & Customer
Modules : Disk
Authors : rb
Test #1 : Run "Disk -conf"
Expect : There should be a "ControllerInOrExt" field with either "Internal" or
"External" for data
for all controllers.

Issue : Added Functional Test Block 14 for PCBA test

Systems : All
Impact : Factory & Customer
Modules : Disk
Authors : rb
Test #1 : Run "Disk -f:14"
Expect : Test should pass

Issue : Change drive "consistency check" to a normal message instead of a

warning.
Systems : Any with raid
Impact : Factory & Customer
Modules : ServerMgmt
Authors : rs
Test #1 : Run as normal.
Expect : Should not longer get the intermittent warning for the drive check.

Issue : WinGui shows extra duplicate columns when resized

Systems : Any
Impact : Factory & Customer
Modules : WinGui.exe
Authors : marky
Test #1 : Resize winGui
Expect : Verify health window operates normally and does not show extra columns

Build 6007:
-----------------------------------------------------------------------------------
----------------------------------

Issue : BIOS incorrectly supports BIOS-Diag panel interface functions on desktops

Systems : Anakin and Sidious
Impact : Factory & Customer
Modules : Nbpanel
Authors : vinod
Test #1 : Nbpanel
Expect : Module does not support this system.

Issue : Added cable detections for Katsiki based on SSI level hardware and the
X00-01 schematics
Systems : Katsiki, Tambor
Impact : Factory
Modules : Cables
Authors : carl
Test #1 : Cables -conf
Expect : List of cables reflects the current status of the cable.
Note : Issues with the X04 BIOS include not having a valid BAR defined in the
SIO. SIO based detections
will not work properly.

Issue : Added XML capability to KeyBoard module

Systems : ALL
Impact : Customer and Factory
Modules : KeyBoard
Authors : rbB
Test #1 : keyboard -?, keyboard -conf
Expect : text output
Test #1 : keyboard -? -xml, keyboard -conf -xml
Expect : xml tagged output

Issue : Removes a debug print statement

Systems : ALL
Impact : Customer and Factory
Modules : SystemConfig
Authors : rb
Test #1 : N/A
Expect : N/A

Issue : Fixes an issue loading the USB driver when the directory name contains
spaces.
Systems : ALL
Impact : Factory and Customer
Modules : DDUsbDiag
Authors : bt
Test #1 : Run c:\"My test"\DDUsbDiag
Expect : All tests should pass.

Issue : Added USB disk device (Blacktop flash) tests

Systems : ALL
Impact : Factory and Customer
Modules : Disk
Authors : rb
Test #1 : On a system with blacktop run "disk -f:1 -mon -d:HDDUSB"
Expect : All tests should pass.

Issue : Added OBIST detection for Optical devices

Systems : ALL
Impact : Factory and Customer
Modules : Disk
Authors : bb
Test #1 : On a system with an optical device run "disk -conf"
Expect : Optical device should have entries for OBIST values

Issue : Warning: Scripts should be checking the module errorlevel to detect

failures. A new "ModErrorLevel" XML
tag was created so a user can now parse the the module exit code from the
XML output.
Systems : ALL
Impact : Factory and Customer
Modules : all
Authors : bt
Test #1 : Validate the module returns the correct errorlevel in the the XML output.

Expect : ModErrorLevel reported in the XML output should contain the correct
errorlevel.

Issue : Port devices now contain a check for port status and will now report a
PASS/FAIL state.
Also fixed a fatal exception when there is a port failure, for example
and over current.
Systems : All
Impact : Factory and Customer
Modules : DDUsbDiag.exe
Authors : bt
Test #1 : run DDUsbDiag
Expect : All tests should pass

Issue : Included updated drivers and dlls for iaStor, S100, S300 and storelib
Systems : All
Impact : Factory and Customer
Modules : Disk
Authors : rb
Test #1 : run disk -f:1 -mon
Expect : All tests should pass

Issue : Make SEL Clear and iDrac reboots FACTORY_ONLY.

Systems : Any IPMI
Impact : Customer
Modules : ServerMgmt
Authors : rs
Test #1 : Build for CUSTOMER_ONLY. Run "servermgmnt -?"
Expect : The SEL Clear, iDrac reboot and related parameters are not present.
Test #2 : Run "servermgmt -selClear"
Expect : This should be a parameter error.

Issue : Do not fail for modules that do not apply to the system for CUSTOMER
only.
Systems : ALL
Impact : Customer
Modules : all
Authors : rs
Test #1 : Build for CUSTOMER_ONLY. Run each module with no parameters.
Expect : If the module does not apply to the system, it should clearly state so
and return with exit code 0.

Issue : Added -f:20 special block testing

Systems : ALL
Impact : None
Modules : Memory.exe
Authors : bbw
Test #1 : run memory -f:20 -xml
Expect : Should see percents increment by 20 and the test should run relatively
fast.

Issue : Changed memory test sequences to match new TS input

Systems : ALL
Impact : None
Modules : Memory.exe
Authors : bbw
Test #1 : run memory -?
Expect : confirm test blocks 1-8 are valid options.

Issue : Support various customer diagnostic user interface issues

Systems : ALL
Impact : Customer
Modules : winGui.exe
Authors : marky
Test #1 : Wingui
Expect : Verify F1 key pops up help menu in devices window, same as Help, Basic
Help menu
: Verify Expert, Command Line Syntax menu describes various options
: Verify 'Wingui -i1' runs without interaction
: Verify console window first few lines shows system info similar to:
: winGui Version 1.1.0.0, ServiceTag BD043BD, SystemID 01C2, Model Latitude
D620
: Verify optional winGui.ini can be edited to allow additional options to
modules
: Verify ESC from disk.exe or other modules occurs within 15-20 seconds
with 1 or 2 disks
: Verify 'winGui -?' pops up command line syntax menu, then exits with
error when OK clicked.
: Verify windows behind "Begin Test?" MessageBox redraw properly
: Verify USB groups, when tested, run all devices in group, not jsut first
one.
: Verify WinGui runs in 64-bit OS as well as 32-bit.
: Verify WinGui runs from a directory that contains an embedded SPACE in
pathname.

Issue : Update scriptor for new modules and memory functional block args
Systems : ALL
Impact : ODM
Modules : scriptor.exe
Authors : marky
Test #1 : scriptor
Expect : Add ddusbdiag, nbpanel, etc. and updates new memory.exe function block
levels.

Issue : Add eventLog.exe utility to the release.

Systems : ALL
Impact : Factory and Customer
Modules : eventlog.exe
Authors : rods
Test #1 : Run "eventlog -?" to see available options.
Expect : N/A

Issue : Change IPMI library to lock the interface during read of SDR. Keeps
multiple applications
: that use the interface from causing unnecessary retries when reading the
records.
Systems : All IPMI
Impact : Factory and Customer
Modules : ServerMgmt, Fan, EventLog.
Authors : rs
Test #1 : On an IPMI system, run the modules at the same time.
Expect : The modules will pause and wait for the interface to free up.

Build 6006:
-----------------------------------------------------------------------------------
----------------------------------

Issue : Added multi-media key functionality for US KeyBoard

: Added numeric-pad keys interface to Help menu
Systems : Paltrow, Reebok
Impact : Factory
Modules : keyboard.exe
Authors : robib
Test #1 : Help->Display Multi-media keys
Test #2 : Help->Display Numeric Pad keys
Test #3 : Test above keys to confirm scan code received by module
Expect : Shows multi-media keys and Eject key

Issue : Added CPLD version information to servermgmt module in the -conf section
Systems : All systems that support Dell OEM command for extracting CPLD version
(command 0x33)
Impact : Factory and Customer
Modules : servermgmt.exe
Authors : fritzk
Test #1 : servermgmt -conf
Expect : CpldRev "tag" in the -conf section, example: 1. 0. 3
Issue : Change ServerMgmt to use the library to clear the SEL
Systems : Any IPMI
Impact : Factory and Customer
Modules : ServerMgmt
Authors : rs
Test #1 : run "servermgmt -SelClear"
Expect : System should clear the event log.

Issue : Update eventlog library to retrieve the BiosDiagProtocol.

Systems : Any
Impact : Factory and Customer
Modules : Memory, eventlog
Authors : rs
Test #1 : Run as normal
Expect : Module should behave as expected.

Issue : Consolidate several redundant variables. Change so SleepSeconds and

noInit parms are shown for help.
Systems : Any IPMI
Impact : Factory and Customer
Modules : ServerMgmt
Authors : rs
Test #1 : The only outward change is for help ("servermgmt -?").
Expect : The "noInit" and "SleepSeconds" parameters should now show.

Build 6005:
-----------------------------------------------------------------------------------
----------------------------------

Issue : Watchdog timer timing out during seek tests

Systems : Horton with H200
Impact : Factory and Customer
Modules : Disk
Authors : rb
Test #1 : run "disk -f:3" on Horton with H200
Expect : System should pass

Issue : Drives connected to Intel RAID controller but not in RAID set failing
Systems : Reebok and Arrowhead set to RAID but no RAID defined
Impact : Factory and Customer
Modules : Disk
Authors : rb
Test #1 : run "disk -f:1" on Reebok and Arrowhead set to RAID but no RAID
configured
Expect : systems should pass

Issue : Chassis Service Tag being shown for Blade Service Tag
Systems : Blade servers
Impact : Factory and Customer
Modules : SystemConfig
Authors : rb
Test #1 : run "SystemConfig -conf -xml" on Blade
Expect : Blade Service Tag should be dipslayed in output.

Issue : DF377193: Reebok failing DST

Systems : Reebok
Impact : Factory and Customer
Modules : Disk
Authors : rb
Test #1 : disk -f:7 -mon
Expect : DST should pass

Issue : CR383369: Add ZeroDrive utility

Systems : All
Impact : Factory and Customer
Modules : Disk
Authors : rb
Test #1 : Build a system with an O/S. run "disk -ZeroDrive -d:HDD:n" where n is the
drive instance that holds
: the O/S.
Expect : First 1GB and last 1GB of drive should be zeroed. This is a dangerous
test as no operator input is
: required to delete data on the disk.

Issue : DST timing out on Bluefish with Hitachi drives

Systems : Bluefish
Impact : Factory and Customer
Modules : Disk
Authors : rb
Test #1 : disk -f:7 -mon
Expect : DST should pass

Issue : Updated help to include Functional Test Blocks (FBT) 9 - 14

Systems : All
Impact : Factory and Customer
Modules : Disk
Authors : rb
Test #1 : disk -?
Expect : Help screen should display FBTs 1 - 14

Issue : Enable multiple IPMI agents to run simultaneously

Systems : All
Impact : Factory and Customer
Modules : Fan, ServerMgmt
Authors : rs
Test #1 : Run "servermgmt" in one window then "fan -conf" in another.
Expect : Both programs should complete correctly.

Build 6004:
-----------------------------------------------------------------------------------
----------------------------------

Issue : Update BMC reset sequence following IPMI fan testing.

Systems : Horton
Impact : Factory and Customer
Modules : Fan
Authors : rs
Test #1 : Run "fan" then run "servermgmt".
Expect : Both modules should perform as expected. Previously, servermgmt
intermittently would not be able to
: communicate with the BMC.

Issue : Fix incorrect status in IPMI command issue.

Systems : Horton
Impact : Factory and Customer
Modules : ServerMgmt
Authors : rs
Test #1 : Run "servermgmt -SleepSeconds:10".
Expect : System should reset and stay off the required number of seconds.

Issue : Eliminate check for zero digit in firmware version.

Systems : Wocket
Impact : Factory and Customer
Modules : ServerMgmt
Authors : rs
Test #1 : Run "servermgmt".
Expect : System should run and find IPMI interface normally.

Issue : Format Windows events in IPMI library.

Systems : Horton
Impact : Factory and Customer
Modules : ServerMgmt
Authors : rs
Test #1 : Run "servermgmt -selDump".
Expect : The output should now be able to show the OEM events as Windows
boot/shutdown.

Issue : Add unique error codes to messages.

Systems : Horton
Impact : Factory and Customer
Modules : Fan, ServerMgmt
Authors : rs
Test #1 : No specific test.
Expect : If the module fails, the results contain better error codes.

Issue : Add check after setting write cache state

Systems : All
Impact : Factory and Customer
Modules : Disk
Authors : rb
Test #1 : Run "disk -WriteCacheDisable"
Expect : Test should pass
Test #2 : Run "disk -WriteCacheEnable"
Expect : Test should pass
Test #3 : Run "disk -conf"
Expect : WriteCache state should be displayed in output for all hard drives

Issue : Put N/A in -conf fields that have no entry

Systems : All
Impact : Factory and Customer
Modules : SystemConfig
Authors : rb
Test #1 : Run "SystemConfig -conf -xml"
Expect : CPU and BaseBoard Output should display N/A in fields that have no data

Issue : Remove -WriteCacheEnable and -WriteCacheDisable for Motherboard SATA

drives
Systems : All
Impact : Factory and Customer
Modules : Disk
Authors : rb
Test #1 : Run "disk -WriteCacheDisable" on system with SATA drives connected to
motherboard controller
Expect : Test should pass
Test #2 : Run "disk -WriteCacheEnable" on system with SATA drives connected to
motherboard controller
Expect : Test should pass

Issue : Remove -WriteCacheEnable and -WriteCacheDisable for SATA drives connected

to Intel RAID controllers
Systems : All
Impact : Factory and Customer
Modules : Disk
Authors : rb
Test #1 : Run "disk -WriteCacheDisable" on system with SATA drives connected to
Intel RAID controller
Expect : Test should pass
Test #2 : Run "disk -WriteCacheEnable" on system with SATA drives connected to
Intel RAID controller
Expect : Test should pass

Build 6003:
-----------------------------------------------------------------------------------
----------------------------------

Issue : Release 6003 Built: 3/19/2010

Systems : Arrowhead, Horton, Reebok, Paltrow
Impact : Factory
Modules : Server Management - serverMgmt.exe
System Management - sysman.exe
LCD Panel - nbpanel.exe
Cables - cables.exe
Disk - disk.exe
Memory - memory.exe
Battery - battery.exe
Fans - fan.exe
USBBist - usbbist.exe
Serial - serial.exe
SysConfig - systemconfig.exe
Authors : delldiag team
Test #1 : Run the executable. Use -? for help or -conf for the configuration
supported on this platform
Expect : Help output if use -?. Configuration output if use -conf.

Issue : Added cable testing for Horton and Arrowhead. Added PAID cable testing
for all portables
Systems : Arrowhead, Horton, all portable platforms supporting PAID
Impact : Factory
Modules : Cables
Authors : carl, fritz, rod
Test #1 : Cables -conf
Expect : Configuration of the cables supported on the system
Test #2 : Cables
Expect : Test to PASS if all required cables are installed. FAIL if any one
required cable is not installed.
User must parse the test output for status of Optional cables, chassis ID
and riser ID.

Issue : Added noteboook panel testing for Paltrow and Reebok.

Systems : Paltrow and Reebok
Impact : Factory
Modules : nbpanel
Authors : vinod
Test #1 : nbpanel
Expect : All tests (interactive and non-interactive) to run successfully
Test #2 : nbpanel -i
Expect : Only the interactive test to run successfully
Test #3 : nbpanel -ix
Expect : Only the non-interactive test to run successfully

Issue : Add scanning event log during testing

Systems : All
Impact : Factory
Modules : memory
Authors : rods
Test #1 : memory -f:N
Expect : All tests should run as normal. If the event log(s) contain any memory
related entries, those should
: be shown.

Issue : Added serial port testing for Horton and Arrowhead

Systems : Arrowhead, Horton
Impact : Factory
Modules : serial
Authors : haiming
Test #1 : serial -conf
Expect : Configuration of the serial ports supported on the system
Test #2 : serial
Expect : Interactive test, tester needs to attach external loop back connector
: Test should pass for different of baud rates
: No test is now available for serial ports that are not exposed to exteral

Issue : Add support for IPMI fans

Systems : Horton
Impact : Factory
Modules : fan
Authors : rods
Test #1 : fan -conf
Expect : Detect and display the fans with current speed.
Test #2 : fan
Expect : System fans will be set to two different speeds and verified that the
: high speed is at least 15% above the lower speed.

Issue : Add support for H200 controller

Systems : Horton
Impact : Factory and User
Modules : disk
Authors : rogerb
Test #1 : disk -conf
Expect : detect and display H200 controller and drives connected to the controller
Test #2 : disk -f:3 -mon
Expect : Drives should be displayed in screen Status area and all tests should run
as normal.

Issue : Added support for USB BIST and USB device testing
Systems : All
Impact : Factory
Modules : ddusbdiag.exe, ddusbdriver.sys
Authors : BryanT
Notes : This module does not support hot plugging of the USB devices. Also note
that on USB BIST
devices we load the Dell USB driver and it remains installed until the
system is rebooted.
Because of this the native driver is not loaded and the device will no
longer respond
to OS requests.
Test #1 : ddusbdiag -conf
Expect : All USB device are detected correctly.
Test #2 : ddusbdiag
Expect : All USB device tests pass. All USB BIST compatible device tests pass.

Issue : Add support for Intel RAID controller

Systems : Reebok and Arrowhead
Impact : Factory and User
Modules : disk
Authors : rogerb
Test #1 : disk -conf
Expect : detect and display Intel RAID controller and drives connected to the
controller
Test #2 : disk -f:6 -mon
Expect : Drives should be displayed in screen Status area and all tests (except
DST Short) should run as normal.
DST is currently NOT supported on drives configured in a RAID connected
to Intel controller.

Issue : Add -conf support for IEEE1394 HDDs

Systems : All
Impact : Factory and User
Modules : disk
Authors : rogerb
Test #1 : disk -conf
Expect : detect and display IEEE1394 HDDs connected to system

Cut and Paste information:

-----------------------------------------------------------------------------------
----------------------------------
Issue :
Systems :
Impact :
Modules :
Authors :
Test #1 :
Expect :