Copyright 2009 OLYMPUS CORPORATION All Rights Reserved.

Paper Craft Assembly Manual

 Pen-F Paper Craft Assembly Manual Copyright 2009 OLYMPUS CORPORATION All Rights Reserved. 1/6

Before assembly: Tips on assembly:

• Print all the parts (Photo-quality paper is recommended for ink-jet printers and paper 1 ) Before detaching parts from the sheets, first use a used ballpoint
of medium thickness (0.20 mm) for laser printers.) pen, a stylus or other pointed tool to make a light crease along
• Print this manual. the folding lines, to make it easier to fold neatly later on.
• Prepare the following:Scissors,Hobby knife (cutting blade), Ruler, Tweezers,Pointed
2 ) To remove the parts from the printed sheet, cut carefully along
tool (e.g., used ballpoint pen, stylus, awl),Glue for wood or paper craft,Marker,Desk the outer edge of the solid lines.
pad for craft making.
3 ) It is useful to gently write a number on the back of each part for
easier identification later on.
Explanations on lines and symbols: 4 ) When cutting a straight line, try to draw the paper toward you as
you cut, rather than moving your scissors away from you; this will
* Unless instructed otherwise in the manual, the parts
{ } Cut along the line. should be“mountain folded” so that the printed produce a cleaner cut. If you use a hobby knife, put a pad
surface will be on the outside of the folded shape.
{ } Mountain fold (Fold along the line. underneath to protect the desk surface and use a ruler.
The printed surface should be on the outside of the folded shape.)
5 ) Similarly, try to hold the scissors steady and rotate the paper as
{ } Valley fold (Fold along the line. The printed surface should be on the inside you cut rounded parts for a better cut.
of the folded shape.)
6 ) Each part should be gently bent for easier gluing and accurate
{ } Cut out the shaded area.
assembly.
{ } Sections with red dots are margins for gluing or gluing surfaces.
7 ) When folding along a straight line, it is best to use a ruler.
{ } When gluing one section to another section, align the edges of that part with
the dotted lines. 8 ) For the lens and other contoured parts, the section should be
rubbed against the corner of a desk or other rounded surface to
give them a natural curve before gluing.
Note on printing 9 ) A number of fine parts are involved in the assembly. The key is to
let the adhesive dry adequately. Also, be careful not to blot the
When printing the file with Adobe Reader, make
parts with glue remaining on your fingers.
sure to switch from “Shrink to Printable Area”
(default) to “None” under the Page Scaling heading, 10 ) If you use glue for wood craft, spread the adhesive on a piece of
paper first, then use a strip of thick paper to scoop the adhesive
which appears in the Print dialog box (see the
and apply a thin layer of adhesive over the “glue margins.”
diagram on the right), to create a model scaled to
the actual size. 11 ) Hold the parts firmly until the glue becomes dry.
12 ) Assemble each part first before putting all parts together for final
Click here and choose “None.” assembly of the entire model.
 Pen-F Paper Craft Assembly Manual Copyright 2009 OLYMPUS CORPORATION All Rights Reserved. 2/6

1 Assembling the body

E
1) Assemble the mirror box Glue margin
Printed face inwards

E
F
Glue margin

Glue F to back of E

2) Glue mirror box to back of body 3) Assemble body

B

Curve body
A before gluing

A
Align from front then glue
 Pen-F Paper Craft Assembly Manual Copyright 2009 OLYMPUS CORPORATION All Rights Reserved. 3/6

2 Assembling smaller components

Viewfinder eyepiece frame Film winding lever Rewind knob
K
J-3
H Picture
J-2

L
I-1 J-1
Face printed side to H

Bend
I-2

I-3

Shutter speed dial Strap eyelets Lens release buttons Shutter button

M-1 Q-1 Q-1

P-1 R
M-2 P-2 Q-2
X2 Q-2 X2
X2
Q-3
P-3 Q-4
M-3
X6

M-4
M-5 N

O
 Pen-F Paper Craft Assembly Manual Copyright 2009 OLYMPUS CORPORATION All Rights Reserved. 4/6

3 Assembling the lens

1) Assembling the front frame 2 ) Assembling 3) Assembling 4) Finishing lens

the lens body - 1 the lens body - 2
U Align this line to marking on W Starting from the seam on the body,
glue on [a] parts so they wind round the lens

X
W
T

w-2 w-1

The colored mark on the glue margin How [w] parts fit together
of W indicates where X should be
affixed. w-2
Glue X so it is in the center of W
w-3 w-4 w-1
X

W W body
w-3 w-4
 Pen-F Paper Craft Assembly Manual Copyright 2009 OLYMPUS CORPORATION All Rights Reserved. 5/6

4 Assembling the body

AH
AH is an internal support rod for reinforcing the body.
The camera can be assembled without it.

Body seam

Bottom view D unprinted

D unprinted Bottom view of body side
side of body Viewfinder Film winding lever
eyepiece frame

Body seam
Aligning grey glue margin on body Aligning grey glue margin on body
with flat part of D before joining left and with flat part of D before joining left and
right surfaces will make assembly easier. right surfaces will make assembly easier.

D
 Pen-F Paper Craft Assembly Manual Copyright 2009 OLYMPUS CORPORATION All Rights Reserved. 6/6

5 To complete
Shutter button

Z
Rewind knob
AA
C

Strap eyelet Strap eyelet

AA-1

Shutter speed dial

AB

Lens release buttons

AC

Lens mount assembly

AD AE AF AG