TSH24

HIGH PERFORMANCE
QUAD BIPOLAR OPERATIONAL AMPLIFIER

■ HIGH GAIN BANDWIDTH PRODUCT :

25MHz
■ HIGH SLEW RATE : 15V/µs
■ SINGLE OR DUAL SUPPLY OPERATION :
3V TO 30V (±1.5V to ±15V)
■ LOW VOLTAGE NOISE : 14nV/√Hz
N
■ NO PHASE INVERSION DIP14
(Plastic Package)
■ ESD TOLERANCE : 2kV
■ LATCH-UP IMMUNITY
■ SPICE MACROMODEL INCLUDED IN THIS
SPECIFICATION

D
SO14
DESCRIPTION (Plastic Micropackage)

TheTSH24 is a quad bipolar operational amplifier

offering a single supply operation from 3V to 30V
ORDER CODE
with very good performances : medium speed
(25MHz), unity gain stability and low noise. Package
Part Number Temperature Range
N D
The TSH24 is therefore an enhanced replacement
of standard dual operational amplifiers. TSH24I -40°C, +125°C • •
N = Dual in Line Package (DIP)
D = Small Outline Package (SO) - also available in Tape & Reel (DT)

PIN CONNECTIONS (top view)

Output 1 1 14 Output 4

Inverting Input 1 2 - - 13 Inverting Input 4

Non-inverting Input 1 3 + + 12 Non-inverting Input 4

VCC + 4 11 VCC -

Non-inverting Input 2 5 + + 10 Non-inverting Input 3

Inverting Input 2 6 - - 9 Inverting Input 3

Output 2 7 8 Output 3

November 2001 1/11

TSH24

SCHEMATIC DIAGRAM (1/4 TSH24)

ABSOLUTE MAXIMUM RATINGS

Symbol Parameter Value Unit
VCC Supply Voltage ±18 to 36 V
Vid Differential Input Voltage 1) ±36 V
Vi Input Voltage (see note 1) ±18 V
Output Short-circuit Duration 2) Infinite
Toper Operating Free-Air Temperature Range -40 to +125 °C
Tj Maximum Junction Temperature +150 °C
Tstg Storage Temperature Range -65 to +150 °C
ptot Maximum Power Dissipation (see note 2) 500 mW
1. Either or both input voltages must not exceed the magnitude of VCC+ or VCC-
2. Power dissipation must be considered to ensure maximum junction temperature (T j) is not exceeded

OPERATING CONDITIONS
Symbol Parameter Value Unit
VCC Supply Voltage 3 to 30 V
Vid 0 mV
Avd RL = 2kΩ 100 dB
Icc No load, each amplifier 2 mA
Vicm -15.2 to 13.8 V
VOH RL = 2kΩ +13.9 V
VOL RL = 2kΩ -13.9 V
Isink Vo = 0V 40 mA
Isource Vo = 0V 40 mA
GBP RL = 2kΩ, CL = 100pF 34 MHz
SR RL = 2kΩ, CL = 100pF 10 V/µs
∅m RL = 2kΩ, CL = 100pF 36 Degrees
∅m RL = 2kΩ, CL = 300pF 26 Degrees

2/11
 TSH24

ELECTRICAL CHARACTERISTICS
VCC+ = 15V, V cc- = -15V, Tamb = 25°C (unless otherwise specified)
Symbol Parameter Min. Typ. Max. Unit
Input Offset Voltage (Vic = 0V, Vo = 0V) mV
Vcc+ = +15V, Vcc- = -15V 2.5
Vio
Tmin ≤ Tamb ≤ Tmax 3.5
Vcc+ = +5V, Vcc- = 0V 2.5
∆Vio Input Offset Voltage Drift (Vic = 0V, Vo = 0V, T = -40, +85°C) 2 µV/°C
Iio Input Offset Current (Vic = 0V, Vo = 0V) 3 65 nA
Iib Input Bias Current (Vic = 0V, Vo = 0V) 100 650 nA

Vicm Vcc- to V
Common Mode Input Voltage Range
Vcc+-1.8
Large Signal Voltage Gain (RL = 2kΩ, Vo = 0V to +10V 32 100 V/mV
Avd
Tmin ≤ Tamb ≤ Tmax 20
Output Voltage Swing (Vid = ±1V)
V
Vcc+ = +15V, Vcc- = -15V RL = 2kΩ VOH
13.4 13.9
VOL -13.9 -13.5
±Vopp RL =10kΩ VOH 13.4 14
VOL -14.7 -14.1
Vcc+=+5V, Vcc-=0V RL = 2kΩ VOH 3.7
0.15 0.2
VOL
Output Short Circuit Current mA
Io (Vid = ±1V, Vo = 0V) Source 25 37
Sink 25 37
CMR Common Mode Rejection Ratio (Vic = -15V to +13.2V) 80 100 dB
Supply Voltage Rejection Ratio dB
SVR
Vcc+/Vcc- = +15V/-15V to +5V/-5V 90 105
Supply Current (Vo = 0V, no load, each amplifier) mA
Vcc+ = +15V, Vcc- = -15V 2.15 2.75
Icc
Tmin ≤ Tamb ≤ Tmax 3
Vcc+=+5V, Vcc-=0V 2.75
Slew Rate V/µs
SR
(Vi = -10V to +10V, CL = 100pF, RL = 2kΩ, AV = +1) 8 15
GBP Gain Bandwith Product (f = 100kHz, RL = 2kΩ, CL = 100pF) 17 25 MHz
B Unity Gain Bandwith (Open loop) 5 MHz
Phase Margin RL = 2kΩ 50 Degrees
∅m
RL = 2kΩ, CL = 100pF 40
nV
en Equivalent Input Noise Voltage (Rs = 100Ω, f = 1kHz) 14 ------------
Hz
Vo1/Vo2 Channel Separation (f = 20Hz to 20kHz) 120 dB
Total Harmonic Distortion
THD (Vcc = ±15V, f = 1kHz, AVCL = 20dB, RL = 600Ω, Vo = 3Vrms) %
0.003

3/11
TSH24

MACROMODEL

** Standard Linear Ics Macromodels, 1993. * AMPLIFYING STAGE

CONNECTIONS : FIP 5 19 VOFP 6.708333E+02

FIN 5 19 VOFN 6.708333E+02
* 1 INVERTING INPUT
GVNEG 5 19 5 13 1.395908E-05
* 2 NON-INVERTING INPUT
GVPOS 5 19 4 13 1.395908E-05
* 3 OUTPUT
RG1 19 5 8.056996E+04
* 4 POSITIVE POWER SUPPLY
RG2 19 4 8.056996E+04
* 5 NEGATIVE POWER SUPPLY
CC 19 29 1.100000E-08
.SUBCKT TSH24 1 3 2 4 5 (analog)
HZTP 30 29 VOFP 6.545046E+01
********************************************************
HZTN 5 30 VOFN 6.545046E+01
.MODEL MDTH D IS=1E-8 KF=7.976636E-15
CJO=10F DOPM 19 22 MDTH 400E-12

* INPUT STAGE DONM 21 19 MDTH 400E-12

CIP 2 5 1.200000E-11 HOPM 22 28 VOUT 4.054054E+03

VIPM 28 4 1.500000E+02
CIN 1 5 1.200000E-11
HONM 21 27 VOUT 4.054054E+03
EIP 10 5 2 5 1
VINM 5 27 1.500000E+02
EIN 16 5 1 5 1
RPM1 5 80 1E+06
RIP 10 11 1.083333E+00
RPM2 4 80 1E+06
RIN 15 16 1.083333E+00
GAVPH 5 82 19 80 6.00E-07
RIS 11 15 8.942641E+00
RAVPHGH 82 4 3333222
DIP 11 12 MDTH 400E-12
RAVPHGB 82 5 3333222
DIN 15 14 MDTH 400E-12
RAVPHDH 82 83 1000000
VOFP 12 13 DC 0
RAVPHDB 82 84 1000000
VOFN 13 14 DC 0
CAVPHH 4 83 0.12243E-12
IPOL 13 5 2.400000E-04
CAVPHB 5 84 0.12243E-12
CPS 11 15 10.5E-09
EOUT 26 23 82 5 1
DINN 17 13 MDTH 400E-12 VOUT 23 5 0
VIN 17 5 -0.200000e+00 ROUT 26 3 2.472597E+01
DINR 15 18 MDTH 400E-12 COUT 3 5 1.000000E-12
VIP 4 18 1.800000E+00 DOP 19 25 MDTH 400E-12
FCP 4 5 VOFP 7.750000E+00 VOP 4 25 1.824860E+00
FCN 5 4 VOFN 7.750000E+00 DON 24 19 MDTH 400E-12
FIBP 2 5 VOFN 5.000000E-04 VON 24 5 1.824860E+00
FIBN 5 1 VOFP 5.000000E-04 .ENDS

4/11
 TSH24

APPLICATIONS INFORMATION
TSH24 IN COMPARATOR APPLICATION
The TSH24 is a quad high performances opera- Displayed curves below show the device re-
tional amplifier featuring speed of 30MHz and sin- sponse in standard comparator configuration with-
gle supply operation from 3V to 30V. out external components.
Most of operational amplifiers are not suited for Transition speed : Typical transition speed under
comparator use because of low transition speed, a single 5V supply voltage is about 2µs from
output signal incompatible with standard logics 50mV overdrive. VOH min. is 3.7V and V OL max. is
level and mainly, phase inversion. 0.2V (2kΩ load) making it compatible with stan-
The phase inversion occures when a strong differ- dard logic families.
ential signal is applied to the device inputs. The
output level is then inverted and shows a wrong Figures 3 & 4 show output signal transition for a
logic state. The TSH24 does not present this prob- 50mV and 250mV input signal overdrive respec-
lematic behaviour. tively of 3µs and 1µs.

Figure 1 : Basic comparator application Figure 2 : Operating conditions

+5V

Vin+

TSH24 Vout

Vref

2kW

Figure 3 : Transition speed@ 50mV overdrive Figure 4 : Transition speed@ 250mV overdrive

5/11
TSH24

PHASE INVERSION
At high differential input voltage, the TSH24 keeps Figure 5 & 6 show the behaviour in follower stage
the right output level thanks to its specific input with saturation output of TSH24 versus 15MHz
structures. standard operational amplifier.
The advantage is obvious on the following figures
and can be also an advantage in linear use when
saturation might occure.

Figure 5 : Behaviour with TSH24 Figure 6 : Saturation behaviour with 15MHz

standard operational amplifier

Input & Ouput Voltages, Vid (V), Vo (V)

8
Vid
6
4
2
0
-2
Vo
-4
-6
-8
Time (50µs/div)

6/11
 TSH24

INPUT OFFSET VOLTAGE DRIFT VERSUS SUPPLY CURRENT VERSUS SUPPLY

TEMPERATURE VOLTAGE (ALL OP-AMPS)
0.4

0.3
Input Offset Voltage, Vio (mV)

0.2

0.1

-0.1

-0.2

-0.3

-0.4
-50 -25 0 25 50 75 100 125
Temperature, Tamb (˚C)

SINK CURRENT SOURCE CURRENT

50
Output Sink Current, Isink (mA)

45
40
35
30
25
20
15
Tamb = 25˚C
10 Vcc = ±15V
5 Vid = 1V
0
-15 -12 -9 -6 -3 0 3 6 9 12 15
Applied Output Voltage, Vo (V)

SLEW RATE @ 30V SLEW RATE @ 3V

20 0.8
15 Tamb = 25˚C Tamb = 25˚C
Vcc = ±15V
0.6 Vcc = +2V/-1V
Output Voltage, Vo (V)

Output Voltage, Vo (V)

Av = +1 Av = +1
10 0.4
RL = 2kΩ RL = 2kΩ
CL = 100pF CL = 100pF
5 0.2
0 0
-5 -0.2
-10 -0.4
-15 -0.6
-20 -0.8
Time (0.5µs/div) Time (0.2µs/div)

7/11
TSH24

LARGE SIGNAL VOLTAGE GAIN @NO LOAD LARGE SIGNAL VOLTAGE GAIN @ LOAD

20
Output Voltage, Vo (V) 15
10
5
Tamb = 25˚C
0 Vcc = ±15V
-5 No Load

-10
-15
-20
-0.4 -0.3 -0.2 -0.1 0 0.1 0.2 0.3 0.4
Differential Input Voltage, Vid (mV)

SMALL SIGNAL RESPONSE @ 30V SMALL SIGNAL RESPONSE @ 3V

UNITY GAIN BANDWITH @ 30V UNITY GAIN BANDWITH @ 3V

45

40 Tamb = 25˚C
Vcc = +2V/-1V
35 AVCL = 100
RL = 2kΩ
30 CL = 100pF 0
Voltage Gain (dB)

25 30
Gain Phase (degrees)
20 60

15 90

10 120
Phase
5 150

0 180

-5
10k 100k 1M 10M
Frequency, F (Hz)

8/11
 TSH24

CLOSED LOOP BANDWITH @ 30V CLOSED LOOP BANDWITH @ 3V

21 21

18 18 Tamb = 25˚C
Tamb = 25˚C
Vcc = ±15V Vcc = +2V/-1V
15 AVCL = +5 AVCL = 5,2,1 15 AVCL = +5 AVCL = 5,2,1
RL = 2kΩ RL = 2kΩ
12 CL = 100pF 12 CL = 100pF

Voltage Gain (dB)

Voltage Gain (dB)

9 9
AVCL = +2 AVCL = +2
6 6

3 3
AVCL = +1 AVCL = +1
0 0

-3 -3

-6 -6

-9 -9
100k 1M 10M 100k 1M 10M
Frequency, F (Hz) Frequency, F (Hz)

9/11
TSH24

PACKAGE MECHANICAL DATA

14 PINS - PLASTIC DIP

Millimeters Inches
Dim.
Min. Typ. Max. Min. Typ. Max.
a1 0.51 0.020
B 1.39 1.65 0.055 0.065
b 0.5 0.020
b1 0.25 0.010
D 20 0.787
E 8.5 0.335
e 2.54 0.100
e3 15.24 0.600
F 7.1 0.280
i 5.1 0.201
L 3.3 0.130
Z 1.27 2.54 0.050 0.100

10/11
 TSH24

PACKAGE MECHANICAL DATA

14 PINS - PLASTIC MICROPACKAGE (SO)

L G
c1

C
a2
A
b e

b1
a1
s
e3 E

D
M

14 8

F
1 7

Millimeters Inches
Dim.
Min. Typ. Max. Min. Typ. Max.
A 1.75 0.069
a1 0.1 0.2 0.004 0.008
a2 1.6 0.063
b 0.35 0.46 0.014 0.018
b1 0.19 0.25 0.007 0.010
C 0.5 0.020
c1 45° (typ.)
D (1) 8.55 8.75 0.336 0.344
E 5.8 6.2 0.228 0.244
e 1.27 0.050
e3 7.62 0.300
F (1) 3.8 4.0 0.150 0.157
G 4.6 5.3 0.181 0.208
L 0.5 1.27 0.020 0.050
M 0.68 0.027
S 8° (max.)
Note : (1) D and F do not include mold flash or protrusions - Mold flash or protrusions shall not exceed 0.15mm (.066 inc) ONLY FOR DATA BOOK.

Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the
consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from
its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications
mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information
previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or
systems without express written approval of STMicroelectronics.
© The ST logo is a registered trademark of STMicroelectronics

© 2001 STMicroelectronics - Printed in Italy - All Rights Reserved

STMicroelectronics GROUP OF COMPANIES
Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia
Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States
© http://www.st.com

11/11