SCADAPack

350E | 357E
Smart Remote Terminal Units

The SCADAPack™ 300E Smart RTU is a platform built on a • Data concentrator for DNP3, Modbus and DF1 devices
32-bit processor and fitted with a 12...30 Vdc supply, a variety • Communication with up to 13 active SCADA clients, up to
of communication links and a wide range of analog and digital 10 remote/local server devices and up to 100 remote DNP3
I/O that adhere to open standards and can operate in the harsh devices in peer-to-peer mode
demands of a remote environment.
• Remote management suite (revise configuration, modify
programs and update firmware remotely, using open
The SCADAPack 300E controller may be configured and standard DNP3)
programmed locally or remotely and is optionally configurable • Up to 76 integrated digital/analog inputs/outputs, and more
directly from EcoStruxure™ Geo SCADA Expert host software. with I/O expansion modules
It can play multiple roles simultaneously: end point, automation
• 1 Ethernet, 3 Serial, 1 USB configuration port
point, data concentrator, protocol converter, peer-to-peer
• IP2x terminal blocks
device, telemetry router; and use Secure Authentication.
• Operation from -40...+70 °C (-40...+158 °F)
• Cost-effective, compact form factor
The SCADAPack 350E/357E Smart RTU provides the following
features:
When fed from a solar supply, the SCADAPack 350E controller
• Open-standard telemetry protocols IEC 60870-5-101/
can power its embedded analog inputs/outputs using its
-104 and DNP3 level 4 with Security Suite (Secure
integrated auxiliary supply, thus having the ability to switch off
Authentication and/or Data Encryption)
this supply to reduce power consumption and help increase
• Open-standard industrial protocols Modbus™ RTU/TCP and battery back-up autonomy.
DF1 client
• Open-standard IEC 61131-3 programming environment
 se.com 2

SCADAPack
350E | 357E
Smart Remote Terminal Units

Specifications – General characteristics

Controller

• 32-bit ARM7 microcontroller, 32 MHz clock, integrated watchdog timer

Processor
• Two microcontroller IO co-processors, 20 MHz clock

• 16 MB FLASH ROM, 4 MB CMOS RAM, 4 kB EEPROM

Memory
• CMOS SRAM with lithium battery retains contents for 2 years with no power

Event Logging Capacity (events) 20,000 events

Database Capacity Up to 1,000 points

Data Concentrator Capacity (points) Up to 500 in DNP3

Data Concentrator Capacity (devices) Up to 10 in DNP3 and up to 100 in Modbus or DF1

File System Typical Storage Internal: 6 MB

Communications

• RS-485, 2-pole removable terminal block, 2-wire, half duplex, supports baud rates up to 115,200 bps
Serial Port : COM1
• RS-232 port, 8-pin modular RJ45 jack, full or half duplex, or RS-485 port, 2-wire, half-duplex, supports
Serial Port : COM2
baud rates up to 115,200 bps in RS-232 mode

RS-232 port, 8-pin modular RJ45 jack, full or half duplex with RTS/CTS control and operator interface
Serial Port : COM3
power control, supports baud rates up to 115,200 bps

Serial Protocols DNP3 level 4 client/server and peer-to-peer, IEC 60870-5-101 server, Modbus client/server, DF1 client

Ethernet port 8-pin modular RJ45 jack, 10/100 Mbps UTP (10/100 Base-T), transformer-isolated

• DNP3 level 4 in TCP client/server, UDP client/server and peer-to-peer, IEC 60870-5-104 server,
IP Protocol Modbus/TCP Server, Modbus/ TCP Client, Modbus RTU in TCP Client
• NTP Client/Server, Telnet Server, FTP Server, BOOTP Server

• Can simultaneously report to multiple independent active clients: 3 in DNP3, 2 in IEC 60870-5-
101/-104, 5 in Modbus TCP and 3 in Modbus RTU, and connect to up to 100 remote devices in
Client - Server Capability DNP3 peer-to-peer
• As a data concentrator it can manage up to 10 local or remote DNP3 servers, and up to 10 local
servers communicating with Modbus RTU, Modbus TCP or DF1 serial

USB Device USB 2.0 compliant “B”-type receptacle, for local configuration
 se.com 3

SCADAPack
350E | 357E
Smart Remote Terminal Units

Specifications – General characteristics

General

Logic Control IEC 61131-3 SCADAPack Workbench programming suite (LD, ST, FBD & SFC)

SCADAPack 350E: 6, 12-pole connector, 0.0810...3.31 mm2 (28...12 AWG), solid or stranded
I/O Terminations
SCADAPack 357E: 5, 6, 7, 9, 10, 12-pole connectors, 0.0810...3.31 mm2 (28...12 AWG), solid or stranded

SCADAPack 350E: 211.8 mm wide x 140.4 mm high x 46.5 mm deep (8.34 in. x 5.53 in. x 1.83 in.)
Dimensions
SCADAPack 357E: 211.8 mm wide x 181.0 mm high x 66.0 mm deep (8.34 in. x 7.13 in. x 2.60 in.)

Enclosure Corrosion-resistant; zinc-plated steel base and stainless steel cover with black enamel paint

• Conformal coated
Environment • -40...+70 °C (-40...+158 °F) operating, -40...+85 °C (-40...+185 °F) storage
• 5% RH to 95% RH, non-condensing

Shock & Vibration IEC 60068-2-27 (tested up to 15 g), IEC 60068-2-6

Power

Rated Voltage 12...30 Vdc. Limit voltage: 11.5...32 Vdc; turn on voltage: 10...11.5 Vdc; turn off voltage: 9...10 Vdc

Maximum Power 12 W at 24 Vdc (internal 5 Vdc supply fully loaded and Vloop on and boosted, fully loaded)

• SCADAPack 350E typical power consumption (at 20 °C/ 68 °F)

Controller Vloop fully 12 Vdc 24 Vdc

LEDs loaded

Power Requirements Use case 1 OFF 1.6 W 1.5 W

Use case 2 OFF ON 5.1 W 4.9 W
Use case 3 ON 5.2 W 5.0 W

• SCADAPack 357E typical power consumption: up to 8.9 W (with up to 7 analog input/output

loops powered from Vloop supply)

Vloop
Power outputs • Maximum 140 mA at 12 Vdc (booster turned off) or 24 Vdc (booster turned on); can power up to
7 analog input/output loops
 se.com 4

SCADAPack
350E | 357E
Smart Remote Terminal Units

Specifications – Digital and Analog Inputs/Outputs

Controller board

5, user-selectable 0...10 Vdc or 0...20 mA plus over range

1, 0...32.7 Vdc (15-bit) for DC supply monitoring
• Resolution: 15-bit ADC (15-bit over the measurement range in 10 Vdc, 14-bit in 20 mA)
Analog Inputs • Accuracy: ±0.1% of full scale at 25 °C (77 °F), ±0.2% over temperature range
• Input Resistance: 250 Ω or 20 kΩ in 20 mA or 10 Vdc configurations (60 kΩ for 32.768 V)
• Normal rejection mode: 27 dB at 60 Hz
• Sampling rate: 170 ms

2 (optional), 0...20 mA, 4...20 mA, voltage output may be accomplished with external precision resistor
• Resolution: 12-bit over 0...20 mA range
• Accuracy: ±0.15% at 25 °C (77 °F), ±0.35% of full scale over temperature range
• Response Time: less than 10 μs for 10% to 90% signal change
• Power Supply: 12…30 Vdc, external
Analog Outputs • Power (Current) Requirements: 10 mA plus up to 20 mA per output
• Isolation: isolated from RTU logic and chassis
• Load Range: 12 Vdc: 0…375Ω, 24 Vdc: 0…925 Ω
• Logic End-Of- Scan to Signal Update Latency: typically 18... 27 ms
• Status & Reporting: output value
• Controls: Direct Operate, Select Before Operate

8, user-selectable as inputs or outputs (open drain)

As Digital Inputs
• Dry contact
Digital Inputs/Outputs
• Time stamping: 170 ms
As Digital Outputs
• Sinking MOSFET output, rated 30 V, 0.5 A, ground return connected to Chassis Ground

• 1, 0...10 Hz (dry contact)

Counter Inputs
• 2, 0...10 kHz (turbine or dry contact)

Internal Power monitor Power input - analog input and low indication, onboard lithium battery - low indication

Internal Temperature
Controller temperature range -40...+75 °C (-40...+167 °F)
Monitor

I/O board (357E only)

8, software-configurable to 0...20, 4...20 mA , 0...5 or 0...10 Vdc

Analog Inputs Same features as for the 5 analog inputs located on the controller board (see above) except isolation:
• Isolation: 500 Vac from logic and chassis

2 (optional), 0...20/4...20 mA, voltage output may be accomplished with external precision resistor, same features as for
Analog Outputs
the analog outputs located on the controller board

32, 12…24 Vdc

• Turn on voltage: 9 Vdc (minimum), Turn off voltage: 4 Vdc (maximum)
• Over-voltage tolerance: 150% sustained over-voltage without foreseeable damage
Digital Inputs
• DC input current: 0.67 mA at 24 Vdc
• Time-stamping : 170 ms
• Isolation: in group of 8, 1500 Vac from logic supply and chassis

16, relays (Form A)

• 4 contacts share one common
• Isolation : isolated in groups of 4. Isolated from RTU logic, RTU chassis and other groups to 1500 Vac
Digital Outputs
• Maximum Switching Voltage: 30 Vdc or 250 Vac (resistive)
• Maximum Switching Load: 150 W or 1250 VA (5 A)
• Controls: Direct Operate, Select Before Operate, Trip/Close, Latch, Pulse

Additional I/O

Supported modules :
• 5606, 5607, 5608 and 5610, and 5304, 5404, 5411, 5414, 5415, 5505 and 5506

I/O Expansion Maximum number of modules per unit:

• SCADAPack 350E: 8 (*)
• SCADAPack 357E: 7 (*)
(*): to reach this limit, additional power supply modules are required
 se.com 5

SCADAPack
350E | 357E
Smart Remote Terminal Units

Model Code
SCADAPack 350E/357E

Model Select : Controller

TBUP350 SCADAPack 350E, Controller 32-bit, 5 Analog Inputs, 8 Digital I/O, 3 High Speed Counter Inputs

TBUP357 SCADAPack 357E, Controller 32-bit, comes with the above plus additional I/Os

Code Select : Platform

E SCADAPack E Firmware (Configuration Software included), can execute up to two IEC 61131-3 applications

Code Select: SCADA Security

A None

B AGA-12 Encryption for DNP3 (Security Administrator application required)

C DNP3 Secure Authentication SAv2 (Security Administrator application required)

D DNP3 Secure Authentication with AGA-12 (Security Administrator application required)

Code Select: Protocol Option

DNP3 Serial/IP client/server/peer-to-peer, IEC 60870-5-101/104 server, Modbus RTU/TCP client/server, TCP/IP, DF1
5
client

Code Select: License Option

5 DNP3 Data Concentrator License (limit of 500 points from 10 IEDs), supports multiple DNP3 Clients (up to 3)

Code Select : Analog Inputs

P350 : 5 selectable as 0...10 Vdc or 0...20 mA *P357 : adds 8 selectable as 0...2 0mA, 4...20 mA, 0...5 Vdc or 0...10
A
Vdc

Code Select: Digital Inputs/Outputs

A P350 only: 8 Digital I/O, individually selectable as digital input (Dry Contact) or digital output (Open Drain)

P357 only: adds 32 digital inputs (12...24 Vdc), 16 digital outputs (Dry Contact relay for Class I Div 2, Solid State
B
relay for IECEx/ATEX)
 se.com 6

SCADAPack
350E | 357E
Smart Remote Terminal Units

Model Code
SCADAPack 350E/357E

Code Select: Analog Outputs

0 None

1 2 channel Analog Output, 0..20 mA, external DC supply

2 P357 only: 4 channel Analog Output, 0..20 mA, external DC supply

Code Select : Future Option

0 None

Code Selection: Certifications

S With FCC, UL508, CE marking and RCM

X Adds IECEx/ATEX Class I, Zone 2

U Adds cCSAus Nonincendive Electrical Equipment for use in Class I, Division 2, Groups A, B, C and D

Note: Accessories sold separately. This is a Green Premium product and is RoHS-compliant.
Disclaimer: Schneider Electric reserves the right to change product specifications. For ordering information call direct worldwide: +1 (613) 591-1943; Toll Free within
North America: +1 (888) 267-2232 or Email: orderstrss@se.com. For more information visit www.se.com.

Schneider Electric Systems USA

Process Automation SCADA & Telemetry

38 Neponset Avenue, Foxboro, Massachusetts 02035 USA
Direct Worldwide: +1 (613) 591-1943
Email: telemetrysolutions@se.com
Toll Free within North America: +1 (888) 267-2232
www.se.com

Part Number TBULM08002-92 v36

© 2018 Schneider Electric. All Rights Reserved. Schneider Electric, Life is On Schneider Electric, EcoStruxure, Green Premium, Modbus and SCADAPack are trademarks and
the property of Schneider Electric SE, its subsidiaries and affiliated companies. All other trademarks are the property of their respective owners. August 2021