160M Motor Grader B9E00001-UP (MACHINE) POWERED BY C9 Engine(SEBP4...
Page 1 of 6
Fechar o SIS
Tela anterior
produtos: MOTOR GRADER
Modelo: 160M MOTOR GRADER B9E01201
Configuração: 160M Motor Grader B9E00001-UP (MACHINE) POWERED BY C9 Engine
Desmontagem e Montagem
160M and 160 Motor Grader Machine Systems
Número de Mídia -RENR9727-09 Data de Publicação -2020/10/01 Data de Atualização -2020/10/30
i07570278
Wheel Lean Bar - Remove and Install
SMCS - 5225-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
9U-7536 Lift Stand 1
A(1)
4C-5809 Electric Hydraulic Pump Gp 1
OR
A1 504-9791 Lift Gp (60Hz)(2) 1
504-9793 Lift Gp (50Hz)(3) 1
1P-1832 Bearing Pulling Adapter 1
4C-9633 Puller Stud 1
3S-6224 Electric Hydraulic Pump Gp 1
B
6V-3160 Double Acting Cylinder 1
5F-7353 Washer 1
9U-6833 Nut 1
(1)
Use Tooling (A) or (A1) based on requirements.
(2)
Operating Voltage (240 - 480V)
(3)
Operating Voltage (200 - 400V)
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior
of the components should be thoroughly cleaned. This will help to prevent dirt from entering the
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 20/01/2025
160M Motor Grader B9E00001-UP (MACHINE) POWERED BY C9 Engine(SEBP4... Page 2 of 6
internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform
disassembly procedures on a clean work surface. Keep components covered and protected at all
times.
Illustration 1 g01402576
For Tooling (A).
1. Use Tooling (A) to apply slight lifting tension to front axle (1).
Illustration 2 g06362319
For Tooling (A1).
2. Use Tooling (A1) to apply slight lifting tension to front axle (1). Refer to Tool Operating
Manual, NEHS1303, "Lift Group (Stand - 25 Ton)" for more information on Tooling (A1).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 20/01/2025
160M Motor Grader B9E00001-UP (MACHINE) POWERED BY C9 Engine(SEBP4... Page 3 of 6
Illustration 3 g01402581
3. Attach a suitable lifting device onto both ends of wheel lean bar (2). The weight of wheel
lean bar (2) is approximately 57 kg (125 lb).
4. Disconnect strap (3). Remove bolt (4) and retainer (5). Repeat this step for the opposite end.
5. Disconnect the suitable lifting device from one end of wheel lean bar (2).
6. Use the remaining suitable lifting device to remove wheel lean bar (2).
Illustration 4 g01402617
Illustration 5 g06362561
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 20/01/2025
160M Motor Grader B9E00001-UP (MACHINE) POWERED BY C9 Engine(SEBP4... Page 4 of 6
7. Remove lip seals (6) from wheel lean bar (2). Repeat this step for the remaining lip seals.
8. Use Tooling (B) to remove bearing (7) from wheel lean bar (2). Repeat this step for the
remaining bearing.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
9U-7536 Lift Stand 1
A(1)
4C-5809 Electric Hydraulic Pump Gp 1
OR
A1 504-9791 Lift Gp (60Hz)(2) 1
504-9793 Lift Gp (50Hz)(3) 1
1P-1832 Bearing Pulling Adapter 1
4C-9633 Puller Stud 1
3S-6224 Electric Hydraulic Pump Gp 1
B
6V-3160 Double Acting Cylinder 1
5F-7353 Washer 1
9U-6833 Nut 1
D 1P-0510 Driver Gp 1
(1)
Use Tooling (A) or (A1) based on requirements.
(2)
Operating Voltage (240 - 480V)
(3)
Operating Voltage (200 - 400V)
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning
fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be
deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or
damaged, use new parts for replacement. Dirt and other contaminants can damage the precision
component. Perform assembly procedures on a clean work surface. Keep components covered and
protected at all times.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 20/01/2025
160M Motor Grader B9E00001-UP (MACHINE) POWERED BY C9 Engine(SEBP4... Page 5 of 6
Illustration 6 g06362561
1. Use Tooling (B) to install bearing (7) (not shown) into wheel lean bar (2). Install bearing (7)
to a dimension of 7.50 ± 0.40 mm (0.300 ± 0.016 inch) below the face of wheel lean bar (2).
Repeat this step for the remaining bearing.
Illustration 7 g01402617
2. Use Tooling (D) to install lip seals (6) into wheel lean bar (2). Repeat this step for the
remaining lip seals.
Illustration 8 g01402581
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 20/01/2025
160M Motor Grader B9E00001-UP (MACHINE) POWERED BY C9 Engine(SEBP4... Page 6 of 6
3. Use a suitable lifting device to install wheel lean bar (2). The weight of wheel lean bar (2) is
approximately 57 kg (125 lb).
4. Install retainer (5) and bolt (4). Repeat this step for the opposite end.
Note: The gap between retainers (5) and wheel lean bar (2) must be a minimum of 0.80 mm
(0.031 inch).
Illustration 9 g06362319
5. Remove Tooling (A1) from front axle (1). Refer to Tool Operating Manual, NEHS1303,
"Lift Group (Stand - 25 Ton)" for more information on Tooling (A1).
Illustration 10 g01402576
For Tooling (A).
6. Remove Tooling (A) from front axle (1).
Direitos Autorais 1993 - 2025 Caterpillar Inc. Mon Jan 20 11:35:18 UTC-0300 2025
Todos os Direitos Reservados.
Rede Particular Para Licenciados SIS.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 20/01/2025
