MANUAL DE SERVICIO Y DESPIECE

LAVADORA
DWD-FV920T1
 1. Specifications

1.1. Product Specifications

42 lt 44 lt 49 lt 50 lt 54 lt 55 lt 60 lt 59 lt 61 lt 62 lt

Product Type Front Loader

Capacity 5 kg 6 kg 7 kg 8 kg 9 kg 10 kg

Max Spin Speed (r/min) 800 - 1000 - 1200 - 1400 1200 -1400
A+++ A+++ A+++
Energy Efficiency A++ A+++ A+++ A+++ A+++ A+++ (-20%) A+++ -%10
(-10%) (-20%) (-40%)
Washing Efficiency A
800 rpm → D
1000 rpm → C 1200 rpm → B
Spinning Efficiency
1200 rpm → B 1400 rpm → B
1400 rpm → B
Control Panel LED display -

Wash Programs 15 settings

Height 84,5 cm 84,5 cm 84,5 cm 84,5 cm 84,5 cm 84,5 cm 84,5 cm

Dimensions Width 59,7 cm 59,7 cm 59,7 cm 59,7 cm 59,7 cm 59,7 cm 59,7 cm

Depth 49,7 cm 49,7 cm 52,7 cm 55,7 cm 58,2 cm 58,2 cm 58,2 cm

Child Lock
Other Features
Delay Time

1.2. Name Plate

SERVICE INDEX
0000

NUMBER

2
2. Installation Instructions

2.1. Moving and Installing

2.1.1. Removal of Transportation Screw

1. Transportation screws, which are located at the back 4. The holes where the transport screws have been
side of the machine, must be removed before running removed should be covered with the plastic transport
the machine. caps found in the accessories bag.
2. Loosen the screws by turning them anticlockwise with a
suitable spanner.

3. Pull out the screws and rubber washers.

5. The transportation screws that have been removed from
the machine must be re-used in any future transporting
of the machine.

2.1.2. Foot Adjustment

1. Do not install machine on rugs or similar surfaces. 5. Change the level by adjusting the feet upwards or
2. For machine to work silently and without any vibration, it downwards.
should be installed on a flat, non-slippery firm surface. 6. After level has been reached, tighten the plastic
Any suspended floor must be suitably strengthened. adjustment nut again by rotating it upwards
3. You can adjust the level of machine using its feet.
against the base of the cabinet.
4. First, loosen the plastic adjustment nut away from the
cabinet base. 7. Never put cartons, wooden blocks or similar
materials under the machine to balance
irregularities of the floor.

2.1.3. Electrical Connection

1. Washing machine requires a 50Hz supply of 220-

240Volts. THIS APPLIANCE MUST BE EARTHED.
2. A special earthed plug has been attached to the supply Insert the machine’s plug to a grounded
cord of washing machine. This plug must be fitted to an socket which you can easily reach.
earthed socket. The fuse value fitted to this plug should
be 13 amps. If you have any doubts about electrical
supply, consult a qualified electrician.
2.1.4. Water Supply Connection
5. After connection is complete, check for leakage by
1. Washing machine is supplied with a single (cold) water
turning on tap completely.
inlet.
6. Make sure that water inlet hoses can not become folded,
2. To prevent leakage from the connection joints, a rubber
damaged, stretched or crushed when the washing
washer is included in the hose packing. Fit this washer
machine is in its final position.
at the end of water inlet hose on the tap side.
7. Mount the water inlet hose to a ¾” threaded water tap.
3. Connect the hose to the water inlet valve. Tighten the
plastic connector by hand. Please call a qualified
plumber if you are unsure about this.
4. Water pressure of 0,1-1 MPa from tap will enable
machine to work more efficiently.(0,1 MPa pressure
means water flow of more than 8 litres in 1 minute from
a fully opened tap)
3. The end of the drain hose can be connected directly to a
2.1.5. Drain Connection drainage stand-pipe or alternatively to a specific
connection point designed for that purpose on the waste
1. Make sure that water inlet hoses are not folded, twisted, outlet of a sink unit.
crushed or stretched. 4. Do not extend the drain hose or guarantee will be
2. The drain hose should be mounted at a minimum height invalidated.
of 60 cm, and a maximum height of 100 cm from the
floor.

2.2. Detergent Box Group

VALVE1

MAIN

SOFTENER

PREWASH

VALVE2

PREWASH = WATER ENTRY VALVE 1

MAIN = WATER ENTRY VALVE 2
SOFTENER = WATER ENTRY VALVE 1 + VALVE 2

4
3. Operating Instructions

3.1. LCD Screen, Function Buttons & Knobs

PR SW4 SW3 SW2 SW1

PR ON/OFF
SW1 Start / Pause
SW2 Option Selection
SW3 Spin Speed Selection
SW4 Temperature Selection
LD1 Start / Pause Led
LD2 Option Led
LD3 Double dot led
LD4 Led of “1”
D1 7-segment display 1
D2 7-segment display 2
D3 7-segment display 3

3.2. Program List

KNOB
PROGRAM
POSITION
1 Cotton 60°C
2 Cotton 40°C
3 Cotton Prewash
4 Eco 20°C
5 Easy Care
6 Wool
7 Rinse
8 Allergy Safe
9 Spin
10 Delicate / Hand Wash
11 Sports Wear
12 Mix/Duvet*
13 Jeans
14 Daily 60'
15 Rapid 15'**
16 OFF

*Mix algoritm is available for 32, 40, 41+, 42, 44, 44+, 47, 49, 50, 54, 59lts. Duvet algorithm is
available for 55, 60, 61, 62 lts.
**Rapid 15 is available for without twinjet model, Rapid 12 is available for with twinjet model.

5
3.3. Child lock during selection:

Child Lock Machine does not respond to any pressing of buttons or

changing position of program knob. CL at 7 segment display will
Activation make fast blink for 2 sec to
indicate child lock is activated.

1. Press the SW2 and SW3 buttons simultaneously for 3 sec. Child lock during the program:

Machine does not respond to any pressing of buttons or

changing position of program knob. “CL” is visualized on display for
2 sec to indicate child lock activation with tone D buzzer in models
having buzzer option. After 2 sec “CL” indication if fixed off and
remaining time is visualized on display.

In end condition

When cycle is finished child lock is automatically

deactivated. It is not possible to activate child lock during End mode.

Deactivation
In Error Mode
1. Press the SW2 and SW3 buttons simulaneously for 3 sec.
Child lock will be automatically deactivated when error is
detected

Child lock during delay mode:

Child lock can be activated / deactivated during delay

mode. If child lock is active during delay mode, it will be kept locked
until the end of washing (unless user deactivates by pressing SW2
and SW3 buttons simultaneously for 3 sec.)

6
4. Test Mode
Step6: The option 1 button is pushed
4.1. Autotest
The EV1 and EV2 are activated concurrently until it reaches
pressure sensor's first level frequency ( Hz ) for 5 seconds.
* This test is for quick checking of the product. You can not see the
failure codes. Step7: Software will detect NTC's resistance value and will check
if the temperature is between 5°C < Tdetected < 40°C . If it is inside
1. Push SW4 button. Keeping SW4 button pushed, turn the range, heating step will be done. If temperature value is outside
program knob to position 1. the range, then it means NTC is detecting the temperature in a
wrong way and heating step will be skipped.

Step8: Autotest ends and "--" is visualized (T0).

Autotest ends and "End" is visualized on LCD (In the rest of the
models).

2. After 3 sec, door will be locked and machine enters

autotest mode. Release SW4 button. "AU" will be
visualized on LCD.

The test steps are as below;

Step1: The pump is activated for 3 seconds and there is EPS

check , the frequency value should be between the 46.04Hz and
43.40Hz. It checks the EPS and if it is OK it continues the autotest; if
it is NOK then it should give E10 ERROR & cancels the autotest (
goes to the selection mode ). Also if any frequency can not be
detected, then it means there is problem with connection or EPS, so
it gives E10 which is EPS error and cancels the autotest.

Step2: The motor ramps to max spin for 15 seconds. While its
speed rising up to the maximum speed the EV1 (prewash valve) is
activated for 5 seconds and then the EV2 (wash valve) is activated
for 5 seconds.

Step3: The motor reduces speed to stop (depends on the motor

stop time) for 5 seconds. While it is slowing down it activates EV1
and EV2 valve, concurrently.

Step4: The motor turns to right.

Step5: The motor turns to left for 5 seconds.

7
Flow chart of the autotest:

During test “AU” is visualized on display, at the end of the test “--” is visualized and door is unlocked. During test, pressing other buttons makes no change on display.

8
 5. Service Mode
5.1. Service Autotest

End users can only see E1-E2-E3-E4. During service autotest, other failures can be seen.

1. To activate service autotest, Press SW3 button and simultaneously position program knob to 1.

2. After 3 sec, door will be locked, and machine enters service autotest mode. Release SW3 button.
In T0 "SA" will be visualized on LCD. In rest of the models "SAU" will be visualized on LCD.

Selector Selector Selector

Position 1 Position 2 Position 3
Result Result Result

HEATER ON PUMP ON RAPID 15' PROGRAM

When
entering in TEST IS OVER Door will be
Comments : service test, unlocked, machine will go to
door will be END state.
locked.

The test steps are as below ;

Step 1 :
Step 3 :
Selector position 1 will be “HEATER ON”
Before heating it should take water till first level frequency then start Selector position 3 will be “RAPID 15' ”
heating. So machine will make exactly the same algorithm of Rapid 15'.
Heater will be on max. 8 minutes.If temperature doesn’t increase 2°C So, time for selector position 1 is 15 minutes.
in 8 minutes,machine will give NTC failure. ( E05 ). At the end of Rapid 15' the door will be unlocked and machine will go
Or if the NTC connection is broken then it should give again E05 NTC to END mode.
failure.
At the end of heating, "SA" or “SAU” visualization should make slow
blink to indicate that the step is over.
Note : If user changes the selector position, machine will do what is
defined for the new selected position.

Step 2 :

Selector position 2 will be “PUMP ON”

Temperature will be measured, if it is higher than 50°C, it should take
80sec. cooling water and then make "Drain+ 5sec.)

At the end of pump activation, "SA" or "SAU" visualization should

make slow blink to indicate that the step is over.

9
 5.2. Failure Codes
Indication For User Indication For Service
Error Indication Error Number
Yes/No Yes/No
Door is not locked E01 Yes Yes

Door is unlocked during programme E01 Yes Yes

Lack of water E02 Yes Yes

Pump failure E03 Yes Yes

Overflow E04 Yes Yes

NTC or Heater Failure E05 No Yes

Motor Failure - 1 (Tachometer open-short circuit or motor
E06 No Yes
connector is disconnected)
Configuration Failure E07 No Yes

Motor Triac Failure E08 No Yes

Voltage Error E09 Yes Yes

Electronic Pressure Sensor E10 No Yes

Dryer Card Communication Error E11 No Yes

3D Communication Error E12 No Yes

LCD Communication Error E13 No No

Dryer Resistance Failure E14 No Yes

Twinjet Failure E15 No No

High Temperature Error E16 No Yes

Flowmeter Failure E17 No Yes

Dryer NTC Failure E18 No Yes

BLDC Failure E19 No Yes

Pyrojet Failure E20 No Yes

Detergent Dosage Pump Failure E21 No Yes

Softener Dosage Pump Failure E22 No Yes

Communication Failure Between PCB and BLDC Card E23 No Yes

Wrong LCD Software E50 No Yes

Wrong BLDC Software E51 No Yes

*Some of the error codes can not be seen based on changing the product types

6. Troubleshooting Guide
All repairs which must be done on the machine should be done by authorized agents only. When a repair is required for machine or you are un able
to eliminate the failure with the help of the information given below:

 Unplug the machine.

 Close the water tap.

FAILURE PROBABLE CAUSE METHODS OF ELIMINATION

It is unplugged. Insert the plug into the socket.

Fuse is defective. Change fuse.
Start / Pause button has not been
Press the start / pause button.
pressed.
Machine does not
operate. The program knob is in 0 (off)
Bring the program knob on the desired status.
status.
Shut the door properly. You should hear the
The door is not shut properly.
click.
Child lock is active. See page 9.

10
 Water tap is closed. Open water tap.
The water inlet hose may be bent. Check the water inlet hose.
Machine does not The water inlet hose is obstructed. Clean the filters of water inlet hose.
receive water. The water inlet filter is obstructed. Clean the valve inlet filters.
Shut the door properly. You should hear the
The door is not shut properly.
click.
The drain hose is obstructed or
Check the drain hose.
bent.
Machine is not The pump filter is obstructed. Clean the pump filter.
draining water. The clothes are not placed inside
Spread the clothes inside the machine in an
the machine in a well-balanced
orderly and well-balanced manner.
manner.
The feet of machine are not
Adjust the feet.
adjusted.
Transportation screws are not
Remove transportation screws.
removed.
Machine is There is a small amount of clothes
vibrating. It does not prevent operation of the machine.
in the device.
Excessive amount of clothes are
Do not exceed the recommended quantity of
filled in the machine or the clothes
clothes and spared clothes in the machine in a
are not placed in a well-balanced
well-balanced manner.
manner.

FAILURE PROBABLE CAUSE METHODS OF ELIMINATION

Press the start/pause button. In order to stop

the foam, dilute one table-spoon of softener in
Too much detergent has been half liter of water and pour it in the detergent
Excessive foam in
used. drawer. Press the start/pause button after 5-10
the detergent
minutes. Arrange the amount of the detergent
drawer
properly in the next washing process.
Use only the detergents produced for full
Wrong detergent has been used.
automatic machines.
Laundry too dirty for the program
Select a suitable program.
The washing result you have selected.
is bad. The amount of detergent used is Use more detergent according to the
not sufficient. detergent.
Clothes exceeding the maximum Put the clothes in machine in a manner not to
capacity has been filled in machine. exceed its maximum capacity.
The washing result Use the amount of detergent according to the
Water may be hard.
is not good. declaration of the detergent producer.
Distribution of the clothes in Spread the clothes inside the machine in an
machine is not well-balanced. orderly and well-balanced manner.
The water is seen
No failure. The water is at the lower
in the drum during
part of the drum.
washing.
There are residues The pieces of some detergents By calibrating machine for “Rinsing” program,
of detergent on the which do not dissolve in water may make an additional rinsing or eliminate the
clothes. stick to clothes as white stains. stains After drying with the help of a brush.
There are grey In the next washing operation, use the
These stains may be caused by oil,
stains on the maximum detergent amount declared by the
cream or ointment.
clothes. detergent producer.
The unbalanced load control system will try to
distribute clothes in a homogenous manner.
The spinning
No failure. The unbalanced load After clothes are distributed, passage to
process is not done
control works in that way. spinning process will be realized. In the next
or starts with delay.
washing process, place clothes into the
machine in a well-balanced manner.

11
7. Disassembly and Assembly
Instructions
7.1. Top Plate
2. Pull the door up.
1. Remove two screws that fix the top-plate at the back.

2. Push the top-plate back and pull it up.

3. Remove screws that fix the door group.

7.2. Door
4. Put the door outside plastic with helping screwdriver as it is
1. Remove two screws that fix the door. (by using the T25) shown in the picture.

T25

12
5. Remove the door inside plastic as it is shown in the picture. 8. Remove the door handle pim as it is shown in the picture.

6. Remove six screws that fix the door hinge as it is shown in

the picture.

7. Remove the door handle as it is shown in the picture.

13
7.3. Tub Bellows Seal
1. First remove the spring wire fixing the tub bellows seal by
using the small size screw driver.
Pull the tub bellows seal as it is shown in the picture.

7.5. Control Panel

1. Remove the screw which fix the control panel to the front
2. Remove the tub bellows seal-body fixing spring. panel.

7.4. Detergent Drawer

2. Remove three screws fixing the control panel.
1. Remove the detergent drawer and pull it up carefully

14
3. Pull the control panel up.

7. Remove electronic card as it is shown in the picture.

4. Release the cable group as shown in the picture.

5. Remove the cable group as it is shown in the picture.

6. Remove electronic card cover as it is shown in the picture by 8. Remove the cable from display card, remove the display
using small screw driver. card and digit part as it is shown in the picture by using small
screw driver.

15
 7.6. Front Panel
1. Remove the pomp cover as it is shown in the picture.

9. Remove selection button as it is shown in the Picture.

16
2. Remove two screws fixing bottom the front panel. 5. Remove two screws fixing the body group at the front as it is
shown in the picture.

6. Lift upper support braket up slightly it it ishown in the

3. Remove two screws fixing upper the front panel. picture.

4. Remove two screws fixing door lock it is shown in the 7. Remove the pump cover housing as it is shown in the
picture. picture.

17
 7.7. Detergent Drawer Housing
1. Remove detergent drawer group clips from the upper
support bracket as it is shown in the picture.

8. Remove the front panel as it is shown in the picture.

2. Remove the tub seal clamp by using the pliers, which is

attached to the detergent drawer housing.

3. Remove the four connectors that is connected to the feed

valve as it is shown in the picture.

18
 4. Turn the feed valve counter clockwise slightly to remove.
2. Remove two screws fixing the parasite filter.

3. Pull the power cable group up as it is shown in the picture.

5. Remove the detergent drawer screw.

6. Remove the detergent drawer housing assembly. 4. Remove parasite fitler fixing body group as it is shown in the
picture.

7.8. Power Cable Group and Parazit 7.9. Electronic Pressure Switch (EPS)
Filter
1. Remove the connector that is connected to the EPS.
1. Remove the five conectors that is connected to the parasite
filter.

19
 2. Pull the EPS upward to remove as it is shown in the picture. 2. Remove pipe clip fixing the tub outlet hose.

3. Remove the eps hose handcuffs and eps hose as it is shown 3. Remove the connector that is connected to the pump motor.
in the picture.

4. Remove four screws fixing the pump motor.

7.10. Door Lock
1. Remove the connector that is connected to the door lock.

7.12. Front Counterweight

1. Remove four screws fixing the front counterweight on the
front. (Box wrench size 13 mm)
7.11. Pump Motor
1. Remove pipe clip that fixes the drain hose.

20
 2. Pull the counterweight back
7.14. Twinjet System*
*(If product has TJ System)
1. Remove the clamps with the help of screwdriver, pull the hose
upwards and remove it from the nozzle.

7.13. Heater
1. Remove the four connectors that is connected to the heater.

2. Remove the screw that fixes the circulation pump to the body.

2. Remove one nut fixing the heater slightly (box wrench size 8
mm)

3. Lay down the machine backward, press to clips.

3. Hold the heater and pull it out.

4. Remove the circulation pump.

21
5. Remove the pump socket.

7.16. Transport Screw

1. Remove four transport screws (box wrench size 10 mm)

6. The clamps on the pump are slid with the help of pliers and the
hoses are pulled out.

2. Hold the transport screw and pull it out.

7.15. Tub Bellows Seal
1. Remove the tub gasket clip by using small screwdriver.

2. Hold the tub bellows seal and gasket-body fixing spring

together, and pull them up.

22
 c) d)

7.17. Upper Counterweight

1. Remove two screws fixing the upper counterweight by using
box wrench size 13 mm.

3. Remove the four screws fixing the spring hanger sheet iron.

2. Remove the upper counterweight

4. Remove the washing group as it is shown in the picture.

7.18. Washing Group

1. Remove the connector that is connected to the motor.

7.19. Shock Absorber PIN

1. Remove two pins fixing the shock absorber as shown in the
picture.

2. Cut the five lead wire holders as shown the pictures.

a) b)

23
7.20. Belt 7.22. Motor
1. Remove the belt as it is shown the picture. 1. Remove the four screws fastening the motor under the tub
by using T40

7.21. Driven Pulley 2. Pull the motor up for disassembly.

1. Remove the screw fixing driven pulley it is shown the picture

(By using T40).

7.23. Tub Entrance with Bellow Hose

1. Remove the tub entrerance with bellow hose.

2. Remove the driven pulley it is shown the picture.

24
7.24. Pressure Switch Hose Group
7.25. Tub
1. Remove screw fixing the pressure switch water reservoir.
1. Remove twenty four screws fixing tub using box wrench size
8 mm.

2. Remove the tub exit with bellow hose with ball by using box
7.26. Drum
wrench size 10 mm.
1. Remove the drum.

25
8. Component Specifications
8.1. Drain Pump

Drain pump is both a mechanical and elektrical component which is used to drain
water inside the washing machine. It has an synchronous motor inside. For
better performance maintanance, pump filter should be cleaned regularly.

8.1.1. Technical Features

Nominal voltage 220 - 240 V

Nominal current 0.28 A (±10 %)
Nominal power 37 W
Frequency 50 Hz
Resistor (coil) 130 Ω (±5%)
Water flow: 17 L/min(to 1 m height)
Thermal protector YES

8.1.2. Checking of Component

Check the resistance value on the component with multimeter as shown in belows figures.

Resistance value should be between 125- 140 Ω

Checking the component

26
8.2. Resistance

Heating element (Resistance) is a component which is desingned to regulate

temperature of water inside the drum. It has three connections: Phase, notral and
ground connections.

8.2.1. Technical Features

Kind of heating Tubular heating element with NTC – sensor

Nominal voltage 230 V
Nominal power 2000 W (±5%)
Resistance 24,8 ±5% Ω
Thermal fuse 2 – sided

8.2.2. Checking of Component

Check the resistance value on the component with multimeter as shown in below pictures.

Checking the component

27
8.3. NTC

Component which sends signals to PCB about the water temperature inside the tub.

The Resistance (Ohm) value of the NTC decreases as the temperature increases.

8.3.1. Technical Features

Tem (°C) R min (kΩ) R max (kΩ)

-10 54,9 62,6
-5 43,0 48,6
0 33,9 38,1
5 27,0 30,1
10 21,6 23,9
15 17,4 19,1
20 14,1 15,4
25 11,5 12,5
30 9,4 10,2
35 7,8 8,3
40 6,4 6,9
45 5,4 5,7
50 4,5 4,7
55 3,8 3,9
60 3,2 3,3
65 2,7 2,8
70 2,3 2,4
75 1,9 2,0
80 1,7 1,8
85 1,4 1,5
90 1,2 1,3
95 1,1 1,1
100 0,9 1,0

NTC Tempure – Resistance Values

8.3.2. Checking of Component

Check the resistance value on the component with multimeter as shown in below pictures.

Checking the component

28
8.4. Valve

Valve is an electrical and mechanical component which is designed to take water from the network
system into the washine machine. It is operated by PCB card.

8.4.1. Technical Features

Nominal voltage 220 – 240 V

Nominal power 8 VA
Frequency 50-60 Hz
Rated flow: 7 lt/min (±15 %)
Operating water pressure 0.0,3 – 1 Mpa

8.4.2. Checking of Component

Check the resistance value on the component with multimeter as shown in below pictures.

Valve water flow rate should be between 6 lt/min - 8 lt/min.

Each valve bobbin resistance values should be between 3,3 - 4.2 kohm .

Checking the component

29
8.5. Electronic Pressure Switch (EPS)

8.5.1. Technical Features

Electromagnetic field occurs as a result of the vibration of the membrane which is under pressure in the coil. The nucleus part is moved up and down by
the electromagnetic field. The water level is regulated by the frequency which is controlled by the PCB and changes according to the movement of the
nucleus part.

8.5.2. Checking of Component

1. Make sure there are no laundry in washing machine, tap is connected and opened, power cord is plugged. Put no detergent in drawer.
2. Bring porgram knob to position 1 (Cotton 90°C program)
3. Press start button.
4. Wait for water intake step to finish. You can recognise it by listening the water sound or slightly opening and observing detergent drawer.
5. As soon as water intake is over turn program knoc to position 0 (Off position)
6. Check water level from door glass. The water level should be just below door glass as seen in the picture below: (There is a %10 tolerance
with this level)

30
8.6. Motor

The washing machine has an asynchronous motor. It is

controlled by the PCB.

It is essential to check the motor for correct diagnosis and

quick servicing. In the below picture, socket points on the motor
is shown to measure with multimeter.

Tacho
Socket
Terminal

Stator Full Field

Coil Socket
Terminal

Stator Half Field

Coil Socket
Terminal

Motor Socket Terminals

31
Tacho and stator (full field-half field) ohm resistance values for the motor types are listed in the below table.

STATOR AUXILIARY WINDING TAKO

MOTOR CODE SUPPLIER
Resistance Resistance Resistance
32016268 WELLING 2,00 ± %7 Ω NA 66,6± %7 Ω
32030654 G&J 1,86-2,14 Ω NA 60,69-69,83 Ω
32016267 WELLING 1,45 ± %7 Ω NA 66,6± %7 Ω
32031898 G&J 2,10-2,42 Ω NA 60,69-69,83 Ω
32030127 WELLING 1,68 ± %7 Ω NA 66,6± %7 Ω
32028497 NIDEC 1,63 ± %7 Ω 0,82 ± %7 Ω 184 ± %7 Ω
32028498 WELLING 1,377 ± %7 Ω 0,785 ± %7 Ω 66,6 ± %7 Ω
32030432 WELLING 1,68 ± %7 Ω 1,55 ± %7 Ω 66,6± %7 Ω
32017283 WELLING 1,93 ± %7 Ω (AL) NA 66,6± %7 Ω
32013652 HAIER 2,65 ± %7 Ω NA 68,8 ± %7 Ω
32032079 TONLON 2,28 ± %7 Ω NA 70,2± %7 Ω
32030653 G&J 2,28-2,63 Ω NA 60,69 - 69,83 Ω
32037679 KENING 2,10 ± %7 Ω NA 63,6± %7 Ω
32031043 G&J 2,03-2,34 Ω NA 60,69 - 69,83Ω
32027577 WELLING 2.39±7%Ω NA 66,6±7%Ω
32027576 HAIER 2.36±7% NA 68,8± %7 Ω
32019342 WELLING 2,00 ± %7 Ω NA 66,6± %7 Ω
32034697 G&J 1,82 ± %7 Ω NA 65,26± %7 Ω
32032630 HAIER 1,27 ± %7 Ω NA 68,8± %7 Ω
32019343 WELLING 1,67 ± %7 Ω NA 66,6± %7 Ω
32034698 G&J 1,82 ± %7 Ω NA 65,26± %7 Ω
32031529 HAIER 1,27 ± %7 Ω NA 68,8± %7 Ω
32004905 NIDEC 2,70 ± %7 Ω 1,04 ± %7 Ω 184 ± %7 Ω
32027578 WELLING 1,21 ± %7 Ω NA 66.6 ± %7 Ω
32025348 NIDEC 1,72 ± %7 Ω 0,70 ± %7 Ω 184 ± %7 Ω
32028496 ANAIMEP 1,36 ± %7 Ω 0,70 ± %7 Ω 180 ± %7 Ω
32030431 NIDEC 1,50 ± %7 Ω 0,75 ± %7 Ω 184 ± %7 Ω
32033330 WELLING 1,38 ± %7 Ω 0,761 ± %7 Ω 66,6± %7 Ω
32030003 NIDEC 2,25 ± %7 Ω 1,03 ± %7 Ω 184 ± %7 Ω
32028925 NIDEC 2,70 ± %7 Ω 1,14 ± %7 Ω 184 ± %7 Ω
32033617 WELLING 2,04 ± %7 Ω 0,99± %7 Ω 66,6 ± %7 Ω
Resistance values for the motor types

32
8.7. Door Lock

Door lock is activated at the beginning of the program in order to prevent the door
from opening. It can be unlocked approximately after 2 minutes of the program end.
This time delay is caused by the PTC which is assambled in the door lock.

8.7.1. Technical Features

Lock Time (20 °C) 2” – 6”

Unlock Time (20 °C) 35” – 75”
Nominal voltage 220 V
Nominal current 16 (4) A

8.7.2. Checking of Component

Check the resistance value on the component with multi-meter as shown in below figures.
Resistance value on the PTC should be 1000 Ω ±50% at 25 °C. That resistance value can be measured from terminal 3-4 (See wiring diagram page 51
below).

33
 T1 PYTHON EXPLODED VIEW
BEYAZ EŞYA SAN. VE TİC. A.Ş.

CONTROL PANEL PARTS

08.2019
 T1 PYTHON EXPLODED VIEW
BEYAZ EŞYA SAN. VE TİC. A.Ş.

NO PART NAME QUANTITY

400 DETERGENT DRAWER COVER 1
401 CONTROL PANEL 1
402 PR. ADJUSTMENT KNOB GR (470+471) 1
403 PROGRAMME ADJUSTMENT SHAFT 1
405 LIGHT GUIDE DUO 1
411 PCB BOX 1
412 ELECTRONIC CARD 1
415 TRIPLE SELECTION BUTTON 1
469 PROGRAM ADJ. INSERT 1
470 PROGRAM ADJ. KNOB 1
471 PROGRAM ADJ. KNOB COVER 1
474 BUTTON SHAFT/T SERIES 4
492 DISPLAY 1888 LIGHT GUIDE 1
493 DISPLAY 888 COVER/PARDUS 1
494 PCB COVER-SEÇ.BUT.GR. 1
495 T1/T2 CARD GR.AMBER 1
499 LCD COMMUNICATION CABLE-MECHANICAL 1
500 CONTROL PANEL GROUP ( indicated for the website) 1
1100 PCB BOX REAR COVER 1
1102 LIGHTGUIDE INSERT 1

*469-470-471-1102 “This spare part is optional and depends on agreed specifications. Therefore you may not find this position
number in product’s spare part list.”

08.2019
 T1 PYTHON EXPLODED VIEW
BEYAZ EŞYA SAN. VE TİC. A.Ş.

FRONT PANEL PARTS

REF. NO PART NAME QTY

1 BODY GROUP PAINTED 1
2 UPPER TRAY GROUP 1
3 FRONT PANEL GROUP 1
5 ADJUSTABLE FEET GR. 4
9 HOUSING FRAME BELLOW CLIP-PHYTON 1
10 DOOR LOCK 1
24 UPPER SUPPORT BRAKET 1
701 PUMP COVER HOUSING 1
702 PUMP COVER 1
920 FRONT PANEL DROP FIXING PLASTIC-II 4
1200 HINGE SUPPORT SHEET 1
1500 ST 4,2X9,5 TRTSB 2
1501 ISO 7049 ST 4,2X16 TORX 2
1504 ISO 7049 ST 4,2X13 TORX 4
1505 ST 4,8X9,5 PAN HE.WITH COL.TORX UN.SER.E 2
1511 FRONT PANEL DROP FIXING PLASTIC-I-B 2
410 SCREW 4X12 TORX PAN HE.W.COL.UND.HE.SER. 1

08.2019
 T1 PYTHON EXPLODED VIEW
BEYAZ EŞYA SAN. VE TİC. A.Ş.

WASHING GROUP PARTS

08.2019
 T1 PYTHON EXPLODED VIEW
BEYAZ EŞYA SAN. VE TİC. A.Ş.

REF. NO PART NAME QTY

103 REAR TUB GROUP 1
117 FRONT TUB 1
160 DRUM GROUP 1
102 MOTOR 1
113 TUB SEAL 1
101 DRIVEN PULLEY 1
100 BELT 1
SCREW FIXING MOTOR-REAR TUB ASSY.
122 4
(COUNTERSUNK HEAD BOLT 8X28 TORX)
206 TUB ENTERANCE WITH BELLOW HOSE 1
118 TUB BELLOWS SEAL 1
BOLT FIXING FRONT TUB-REAR TUB ASSY.
126 19
(HEXAGON HEAD BOLT 6X30 PT)
805 HEXAGON HEAD BOLT 10 X 52 4
WASHER USED AT COUNTERWEIGHT-TUB ASSYS.
810 6
(CONICAL SPRING WASHER 8.4X18X2 (DIN 6796) (SAFETY))
105 SHOCK ABSORBER PIN 4
119 TUB GASKET CLIP 1
120 FRONT CONCRETE WEIGHT 1
121 RESISTANCE GR 1
999 NTC 1
899 RESISTANCE WITHOUT NTC 1
115 RESISTANCE FIXING WIRE 1
104 SHOCK ABSORBER 2
213 TUB EXIT BELLOW HOSE WITH BALL 1
124 BOLT FIXING DRIVEN PULLEY-DRUM SHAFT ASSY. (37020184 SCREW M8x29 THB) 1
808 MUSHROOM HEAD SQUARE NECK BOLT M 8X65 2
806 PLAIN WASHER 8.4X28X3 2
811 UPPER COUNTERWEIGHT BOLT SUPPORT SHEET 2
NUT FIXING UPPER COUNTERWITGHT-TUB ASSY.
812 2
(HEX.NUT WITH FLANGE SERRATED M8 DIN6923)
813 PLASTIC LIFTER 3
112 UPPER CONCRETE WEIGHT 1
816 RESISTANCE PROTECTION FOIL-1-C 1
SCREW FIXING RES. PROT. FOIL-TUB ASSY.
817 2
(SCREW 3,5X7PAN HEAD WITH COLAR CROSS RE.)
898 PSW HOSE MOUNTING RUBBER-10MM 1
1400 SCREWED HOSE CLAMP Ø65 1
1401 SPRING TYPE BANT CLAMP 1
1402 HOSE CLAMP SCREW TYPE Ø72 1
1403 HOSE CLAMP Ø38,8 1
WASHER USED TO FIX FRONT COUNTERWEIGHT
1507 4
(PLAIN WASHER 10.5X40X2.5)

* 816 - 817 “This spare part is optional and depends on agreed specifications. Therefore you may not find this position number
in product’s spare part list.”

08.2019
 T1 PYTHON EXPLODED VIEW
BEYAZ EŞYA SAN. VE TİC. A.Ş.

DETERGENT DRAWER GROUP

NO PART NAME QUANTITY

200 DETERGENT DRAWER 1
202 SIPHON COVER 1
203 WATER DISTRIBUTION PLATE GROUP 1
205 DETERGENT DRAWER HOUSING 1
207 VALVE-DETERGENT BOX HOSE 1
209 VALVE(TWO EXIT) 1
214 DETERGENT DRAWER LOCKING PART 1
228 PLASTIC HOSE CLAMP 6
996 LIQUID DETERGENT LEVEL PLATE 1
270 DETERGENT BOX GROUP 1
275 DETERGENT BOX GROUP/HOSE 1
280 DETERGENT BOX GROUP/FULL 1

08.2019
 T1 PYTHON EXPLODED VIEW
BEYAZ EŞYA SAN. VE TİC. A.Ş.

PRESSURE SWITCH HOSE GROUP

NO PART NAME QUANTITY

213 TUB EXIT WITH BELLOW HOSE 1
212 PRESSURE SWITCH WATER RESERVOIR 1
211 PRESSURE SWITCH HOSE 1
234 HOSE CLAMP Ø32,7 1
244 HOSE CLAMP Ø9,6 1
295 PRESSURE SWITCH HOSE GROUP 1
213-212-211-234-244-------------------- PRESSURE SWITCH HOSE GROUP

08.2019
 T1 PYTHON EXPLODED VIEW
BEYAZ EŞYA SAN. VE TİC. A.Ş.

BODY GROUP PARTS

08.2019
 T1 PYTHON EXPLODED VIEW
BEYAZ EŞYA SAN. VE TİC. A.Ş.

REF. NO PART NAME QTY

20 WATER ENTRY HOSE GROUP 1
24 UPPER SUPPORT BRACKET 1
285 PUMP GROUP 1
220 DRAIN HOSE ROUTER PLASTIC 1
219 DRAIN HOSE 1
225 ELECTRONIC PRESSURE SENSOR 1
215 EMI FILTER 1
296 CABLE GR 1
249 CABLE HARNESS 1
250 CABLE HARNESS HOLDER PLS 1
331 LOCKING WIRE SADDLE (BLUE) 1
895 SPRONG HANGER BRACKET GROUP 1
800 TUB SPRING 2
231 SPRING HANGER BRACKET 1
221 HANGER SPRING BRACKET PLS. 2
700 TUB HANGER SPRING PART (PLASTIC HOUSING PART BETWEEN TUB AND SPRING HOOK) 2
235 DRAIN HOSE HOLDING PLS 4
239 POWER CORD GROUP 1
222 PRESSURE SWITCH MOUNTING CLIP 1
238 SPEED CONTROL HOLE STOPPER 1
290 TRANSPORT SCREW GROUP-II 4
242 TRANSPORT SCREW PLASTIC-A-II 4
243 TRANSPORT SCREW PLASTIC-B-II 4
240 TRANSPORT SCREW 4
245 TRANSPORT SCREW EPDM 4
241 PLAIN WASHER 8,30X29X2 4
132 CABLE TIE(YKB150) 7
918 PUMP FİLTER 1
919 HOSE CLAMP Ø8,6 1
920 FRONT PANEL DROP FIXING PLASTIC-II 4
*990 DC CARD GROUP 1
1503 ST 4,2X9,5 PAN HEAD W.COL.T.UNDER.SER.EA 2
1504 ISO 7049 ST 4,2X13 TORX 4
1505 ST 4,2X9,5 TRTSB 4

* 990 “This spare part is optional and depends on agreed specifications. Therefore you may not find this position number in
product’s spare part list.”

08.2019
 T1 PYTHON EXPLODED VIEW
BEYAZ EŞYA SAN. VE TİC. A.Ş.

DOOR GROUP

NO PART NAME QUANTITY

6 OUTER DOOR PLASTIC 1
7 DOOR GLASS 1
8 INNER DOOR PLASTIC 1
12 HINGE 1
13 HINGE BUSH 4
14 DOOR HANDLE 1
15 HOOK SPRING 1
26 HANDLE SPRING 1
27 HANDLE PIN 3
28 SCREW 3,5X16 PAN HEAD WITH COLLAR UNDER HEAD SERRATED 9
29 OUTER DOOR PLASTIC INSERT PART 1
31 FRONT DOOR COVER 1
32 OUTER DOOR PLASTIC INNER FRAME 1
33 DOOR HINGE SUPPORT SHEET 1
410 SCREW 4X12 PAN HEAD WITH COLLAR UNDER HEAD SERRATED 6
1502 SCREW M5X8 TSB 2
50 PORTHOLE GROUP (all parts) 1

08.2019
 CÓDIGO NOMBRE DESCRIPCIÓN POSICIÓN
42026020 ENCIMERA UPPER TRAY GROUP/57/SIGMA PLUS 2
47013982 PATAS AJUSTABLES ADJUSTABLE FEET GR SBR-H 5
47003771 CRISTAL DE PUERTA DOOR GLASS/PYTHON 7
37023407 ARO SUJECIÓN GOMA PUERTA FRONTAL HOUSING FRAME BELLOW CLIP-PHYTON-2 9
32024465 INTERRUPTOR DE PUERTA DOOR LOCK M8(TER-METALFLEX) 10
42070217 TIRADOR DE PUERTA DOOR HANDLE/D10 14
35007443 MUELLE DEL CIERRE D. HANDLE COMP(HOOK SPRING) 15
37008931 GANCHO DE PUERTA DOOR HOOK II.(METAL) 17
40014423 TUBO ENTRADA AGUA WATER ENTRY HOSE GR/COLD 20
35007434 PASADOR TIRADOR DOOR HANDLE TONGUE PIM 27
42082634 PUERTA COMPLETA PORTHOLE GROUP B(D11) 50
42025178 CORREA BELT(1200/1400/1600 RPM 52/57)ALVA 100
37000499 POLEA DRIVEN PULLEY ALVA 101
32033617 MOTOR LAVADO MOTOR(12-14/59-60-61 DC)TYPE 27-WELLING 102
20737596 CUBA TRASERA REAR TUB GROUP (52/57C2) 103
47011587 AMORTIGUADOR SHOCK ABSORBER-9 104
42025094 PASADOR AMORTIGUADOR SHOCK ABSORBER PIM-2 105
42059372 CUBA FRONTAL FRONT TUB 60LT-TYPE4 117
42206359 GOMA PUERTA TUB BELLOWS SEAL/PYTHON-D 118
37008555 ARO SUJECIÓN GOMA PUERTA TRASERO TUB GASKET CLIP-PYTHON 119
20846087 RESISTENCIA + NTC RESISTANCE GR.(48/53)Ç.S 2000 W-M 121
20813477 BOMBO DRUM GROUP/60-PEARL-C2-SK 160
42087110 TUBO DE JABONERA A BOMBO TUB ENTERANCE WITH BELLOW HOSE-C 206
32035767 VÁLVULA ENTRADA VALVE(2 EXIT-RAST2,5) 209
32027179 FILTRO ANTIPARÁSITOS PARASITE FILTER(0,47 uF 10 A -DEM) 215
42074837 MANGUERA DESAGÜE DRAIN HOSE-LONG-GREY 219
32025730 PRESOSTATO ELECTRONIC PRESSURE SENSOR 225
42199898 CAJÓN DETERGENTE DETERGENT BOX GR/FULL/COLD/57/6 280
32028671 BOMBA DESAGÜE + FILTRO PUMP(50 HZ-LEILI ALVA) 285
42079698 CAMARA PRESOSTATO + TUBO CUBA PRESSURE SWITCH HOSE GR(ALVA-5)BALL SYST 295
42214692 FRONTAL TECLADO CON.PAN.GR.DAWEOO A5T1(WVD-09T1WW12U 400
42214692 FRONTAL TECLADO CON.PAN.GR.DAWEOO A5T1(WVD-09T1WW12U 401
42210213 DIAL PROGRAMAS PR.AD.KNOB GR/T/G.CHROME-K.BYZ-K2 402
22125604 PLACA FRONTAL COMPLETA VEL.CARD T1-5D8BFFF038000000-V10.3_N-A 412
42214692 FRONTAL TECLADO CON.PAN.GR.DAWEOO A5T1(WVD-09T1WW12U 494
22085030 PCB DISPLAY TECLADO VEL T1/T2 CARD GR.AMBER 495
42187826 TAPA FILTRO BOMBA PUMP COVER/3 702
37014888 MUELLE CUBA TUB SPRING-PYTHON-2 800
42150295 BATEADOR PLASTIC LIFTER 60 LT 813
22085075 PLACA MOTOR DC VEL DC CARD GROUP/F SERISI_5VA 990
32025771 NTC SENSOR NTC TEMP. SEN.-RAST 999
42214692 FRONTAL TECLADO CON.PAN.GR.DAWEOO A5T1(WVD-09T1WW12U 1102