4/2/2021 14M Series 3 Motor Grader E9S00001-UP (MACHINE) POWERED BY C13 Engine(M0066788 - 40) - Documentation
Previous Screen
Welcome: ju2bbt
Product: MOTOR GRADER
Model: 14M-3 MOTOR GRADER E9S
Configuration: 14M Series 3 Motor Grader E9S00001-UP (MACHINE)
POWERED BY C13 Engine
Testing and Adjusting
14M3 and 14 Motor Grader Machine Systems
Media Number -M0070306-05 Publication Date -01/04/2020 Date Updated -30/04/2020
i06678178
Calibration
SMCS - 1400-524; 1901; 3030-524; 3139-524-CL ; 3139-524-JV ; 3139-524-T3 ; 3139-524-VC ; 3155-524-PX
; 3174-524; 4269-524-PSN; 4800-524-JV ; 4800-524-NS ; 4800-524; 4800; 4810-524; 4810; 5050; 5479-524-
JV ; 5479-524-NS ; 5479-524; 5700-524-II ; 5700-524-JV ; 5700-524-NS ; 5700-524; 5700; 6322-524-PXS;
6630; 6631; 7000-EK ; 7000; 7220-524; 7466; 7494-524; 7600-524; 7610-038-ZH ; 7610-524-DTN; 7610-524-
II ; 7610-524-MCH; 7610-524-YW ; 7610-524; 7610-CQ ; 7610-DTN; 7610-MCH; 7856-524
Introduction
Some of the components that are connected to the electronic control modules can be calibrated by using the
Caterpillar Electronic Technician (Cat ET).
Calibrations are performed when directed by troubleshooting procedures or replacing a component within the
calibrated system.
The calibration of a component allows the ECM to determine the correct output level. The calibration also
allows the ECM to determine the correct input signal of displacement.
For more information on error codes that may occur during calibration refer to Testing and Adjusting,
UENR4633, "Calibration Error Codes".
Required Tools
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpage=/… 1/4
4/2/2021 14M Series 3 Motor Grader E9S00001-UP (MACHINE) POWERED BY C13 Engine(M0066788 - 40) - Documentation
Illustration 1 g03142124
Table 1
Required Tools
Part
Tool Item Qty Description
Number
C 1 317-7484(1) Communication Adapter Gp
C1 1 370-4617 Cable As (USB PC Communication)
C2 1 317-7485 Communication Adapter III
C3 1 327-8981 Cable As (Data Link)
C4 1 317-7492 Cable As Wireless Radio
C5 1 JERD2129 Caterpillar Electronic Technician (Cat ET)
(1) Cat Electronic Technician (ET) and Software CD, NETG5057 are required when using the communication adapter.
Cat ET Calibration Screen
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpage=/… 2/4
4/2/2021 14M Series 3 Motor Grader E9S00001-UP (MACHINE) POWERED BY C13 Engine(M0066788 - 40) - Documentation
Illustration 2 g06071032
Calibration screen
Implement ECM Calibrations
The following calibrations can be performed to the Implement ECM:
Auxiliary Solenoid Calibrations
Solenoid Calibrations
Operator Input Calibrations
Cross-Slope Valve Calibrations
Cross-Slope Sensor Calibrations
To access the calibration procedures for the Implement ECM, establish the connections of the Cat ET to the
machine. Navigate to the calibration screen by clicking "Service" on the tool bar and then clicking
"Calibrations". Select the desired calibration procedure that is required. Click on the "Start" button at the bottom
of the screen.
Once the specific calibration is selected, the Cat ET will guide you through the calibration procedure.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpage=/… 3/4
4/2/2021 14M Series 3 Motor Grader E9S00001-UP (MACHINE) POWERED BY C13 Engine(M0066788 - 40) - Documentation
The Cat ET will list initial machine conditions that must be satisfied before the ECM will allow the calibration
procedure to continue. Follow the specific instructions on the display in order to complete the calibration
procedure.
Implement 2 ECM Calibrations
The following calibrations can be performed to the Implement 2 ECM:
Arm Steering System/Solenoid Calibration
Solenoid Calibrations
Steering Cylinder Position Sensors Calibrations
Articulation Position Sensor Calibration
To access the calibration procedures for the Implement 2 ECM, establish the connections of the Cat ET to the
machine. Navigate to the calibration screen by clicking "Service" on the tool bar and then clicking
"Calibrations". Select the desired calibration procedure that is required. Click on the "Start" button at the bottom
of the screen.
Once the specific calibration is selected, the Cat ET will guide you through the calibration procedure.
The Cat ET will list initial machine conditions that must be satisfied before the ECM will allow the calibration
procedure to continue. Follow the specific instructions on the display in order to complete the calibration
procedure.
Transmission/Chassis ECM Calibrations
The following calibration can be performed to the Transmission/Chassis ECM:
Transmission Fill Calibration
To access the calibration procedures for the Trans/Chassis ECM, establish the connections of the Cat ET to the
machine. Navigate to the calibration screen by clicking "Service" on the tool bar and then clicking
"Calibrations". Select the desired calibration procedure that is required. Click on the "Start" button at the bottom
of the screen.
Once the specific calibration is selected, the Cat ET will guide you through the calibration procedure.
The Cat ET will list initial machine conditions that must be satisfied before the ECM will allow the calibration
procedure to continue. Follow the specific instructions on the display in order to complete the calibration
procedure.
Copyright 1993 - 2021 Caterpillar Inc. Thu Feb 04 2021 15:28:04 GMT+0800 (Waktu Standar Tiongkok)
All Rights Reserved.
ju2bbt
Private Network For SIS Licensees.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpage=/… 4/4
