IIT Makina Lite - Alarm receiver manual

IIT Makina Lite

Alarm receiver manual

www.iit.com.hr
6.06.2025.

1
CONTENTS CONTENTS

Contents
1 Preface 4
1.1 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.2 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.3 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2 Introduction 5
2.1 Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.2 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.3 Package contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.4 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3 Installation 8
3.1 Connectors and LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.1.1 Network Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.1.2 SD Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.2 Connecting the receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.2.1 Secure connection scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.2.2 Connection scheme for maximum number of accounts . . . . . . . . . . . . . . . . 10

4 Dashboard 11
4.1 System panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.2 Interface panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.3 Distributor panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.4 Analyzer panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

5 Settings 13
5.1 General settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.2 WAN (ETH0) settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.3 LAN (ETH1) settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.4 Distributor settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5.4.1 Distributor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5.4.2 Distribution options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5.4.3 Contact ID format codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.4.4 SIA DCS format codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.5 Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.6 Accounts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.6.1 New account default values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.7 Watchdog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.7.1 On-line accounts test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.7.2 Database purge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.7.3 Internet connection test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.8 Debug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.8.1 Syslog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.8.2 Loglevel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.9 Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.10 Notifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.10.1 Mail server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
5.10.2 Mail content . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

6 Accounts 21
6.1 Columns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
6.2 Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
6.3 Editor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
6.3.1 Editable fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
6.3.2 Non editable fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
6.4 Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

2
CONTENTS CONTENTS

7 Messages 25
7.1 Columns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
7.2 Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
7.3 View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
7.3.1 View fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
7.4 Messages filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

8 Tools 28
8.1 Export . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
8.1.1 Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
8.1.2 CSV file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
8.2 Import . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
8.2.1 Transport protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
8.2.2 Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
8.3 Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
8.4 Restore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
8.5 Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
8.6 Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
8.6.1 Targets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
8.6.2 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
8.6.3 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
8.6.4 Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
8.7 Restart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

3
 1 PREFACE

1 Preface
Thank you for choosing the IIT Makina Lite alarm message receiver. The receiver uses the latest IoT
technologies to make receiving alarm messages a breeze. It is designed to work seamlessly with various
alarm systems, providing real-time monitoring and alerting capabilities. The receiver is equipped with a
user-friendly web interface that allows you to configure settings, view logs, and manage accounts easily.
It supports multiple alarm protocols and formats, ensuring compatibility with a wide range of alarm
systems, making it versatile for different applications. It can handle multiple simultaneous connections,
allowing it to receive messages from various alarm panels without any issues.
The IIT Makina Lite is built with security in mind, featuring robust encryption protocols to protect
your data and ensure secure communication. The device is compact and energy-efficient, making it
suitable for various installation environments. Its durable design ensures long-term reliability, and it can
be easily integrated into existing monitoring systems.
With additional support for vector instructions in the MCU, which provides acceleration for neural
network computing and signal processing workloads, the IIT Makina Lite is capable of handling complex
tasks efficiently. This feature enhances its performance in processing alarm messages and executing intel-
ligent functions. It provides intelligent functions such as customizable alert notifications, and integration
with third-party applications for enhanced functionality.
The IIT Makina Lite is ideal for security companies, monitoring centers, and individual users who
require a reliable and efficient alarm message receiver. Its advanced features and user-friendly interface
make it a valuable tool for anyone involved in alarm monitoring.

1.1 Safety
The IIT Makina Lite is a CLASS 2, desktop or rack mounted device powered by external power sup-
ply, with a detachable power supply cord. It is designed to be used in a non-hazardous environment,
specifically in a Pollution Degree 2 environment, which means it is suitable for indoor use where normal
conditions of humidity and pollution are expected. The IIT Makina Lite is intended for use in a restricted
access location, accessed onbly by qualified personnel who have the necessary technical knowledge and
experience to handle the equipment safely. This device uses Lithium Batteries. Improper handling of
lithium batteries may result in heat generation, explosion or fire, which may lead to personal injury.

1.2 Maintenance
The IIT Makina Lite is designed to be low-maintenance, with no user-serviceable parts inside. If trouble
is experienced with the device, it is recommended to contact the manufacturer or a qualified technician for
assistance. The device should be kept clean and free from dust and debris to ensure optimal performance.
Regular firmware updates are recommended to keep the device running smoothly and securely.

1.3 Warranty
The IIT Makina Lite comes with a two-year warranty from the date of purchase. This warranty covers
defects in materials and workmanship under normal use and conditions. If a defect arises during the
warranty period, the manufacturer will repair or replace the device at no charge, provided that the device
has not been subjected to misuse, abuse, or unauthorized modifications. Warranty claims should be
directed to the place of purchase or the manufacturer’s customer service department, along with proof
of purchase and a description of the issue. Warranty may be extended with the purchase of an extended
warranty plan within the first year of purchase.

4
2 INTRODUCTION

2 Introduction
2.1 Characteristics
The IIT Makina Lite is a compact and efficient alarm message receiver designed for modern security
systems. It features a sleek design, making it suitable for both desktop and rack-mounted installations.
The device is powered by an external power supply, ensuring reliable operation in various environments.

Figure 1: IIT Makina Lite front panel

Receiver is equipped with a range of features that enhance its functionality and ease of use. On the
front panel, it includes several LED indicators that provide real-time status updates, allowing users to
quickly assess the operational state of the device and two network interfaces for connecting to alarm
systems and other devices.

Figure 2: IIT Makina Lite back panel

On the back panel, receiver features a power connector for the external power supply, RS-232 and
USB ports for data transfer and SD card slot for accounts and alarm messages storage.
The device is designed to be user-friendly, with a straightforward setup process and intuitive operation.
Its compact size makes it easy to integrate into existing security cantral stations without requiring
significant modifications.
The IIT Makina Lite can monitor up to 512 IP supervised alarm accounts, making it suitable for both
small and large installations. Additional 512 IP supervised alarm accounts license may be purchased to
extend the total number of supervised accounts to 1024.
The device supports a wide range of alarm protocols, including SIA DC-09, Contact ID, and Ademco
CID, ensuring compatibility with various alarm systems and devices.
Receiver uses real time clock and NTP protocol to ensure accurate timekeeping, which is crucial for
logging alarm events and maintaining system integrity. Received alarm messages are stored in a local
database and sent to the central station software for further processing and analysis via:

• TCP/IP connection,

• USB connection and

• RS-232 connection.

All messages may be sent to syslog server for further processing and analysis and to e-mail addresses
for notification purposes.
Accounts and alarm messages may be viewed and managed using the web interface, which provides a
user-friendly way to interact with the device. System configuration and management can be performed

5
2.2 Specifications 2 INTRODUCTION

through the web interface, allowing users to easily adjust settings, monitor system status and performs
accounts import and export actions, database backup and restore.
IIT Malina Lite features:

• High performance Xtensa 32-bit LX7 dual-core processor at 240 MHz,

• Secure boot and flash encryption for enhanced security,
• Cryptographic hardware acceleration for secure communication,
• Two 10/100 Mbps W5500 Ethernet interfaces with 32 kb internal buffer,
• Trouble detection and reporting for enhanced reliability,
• DHCP and static IP address configuration for flexible network setup,

2.2 Specifications
• Power:
Power supply: 12V DC, 2A,
Power consumption: 20W (max).
• Dimensions and weight:
Dimensions: 104 mm x 130 mm x 30 mm,
Weight: 260 g.
• Enviromental:
Operating temperature: -20°C to +60°C,
Humidity: 0% to 95% (non-condensing),
Storage temperature: -40°C to +150°C.
• Automation:
TCP/IP port: 11001,
RS-232 and USB ports baudrate: 9600 bps,
RS-232 and USB ports data bits: 8,
RS-232 and USB ports stop bit: 1,
RS-232 and USB ports parity: none.
• Alarm messages interface:
TCP/IP port: 22333,
UDP/IP port: 22333.
• WEB interface:
HTTP port: 80.
• Alarm accounts:
Up to 512 IP supervised alarm accounts,
Additional 512 IP supervised alarm accounts license may extend supervised accounts to 1024.
Maximum number of supervised and nonsupervised accounts is 2048.
• Alarm protocols:
Simple CID (Contact ID) protocol format,
CSV CID (Contact ID) protocol format,
E2 CID (Contact ID) protocol format,
M2M CID (Contact ID) protocol format,
SIA DC-09-2021 protocol,
DC-05-2016-DCS Ademco Contact ID,
DC-04-2000.05 DCS SIA 2000 Format,

6
2 INTRODUCTION 2.3 Package contents

DC-03-2017 DCS SIA Format,

SG-compatible Receiver to Computer Interface protocol
DC-07-2001.04 Receiver to Computer Interface protocol (Type 2),
DC-01-1988 DCS Computer interface (CIS-1),

2.3 Package contents

• IIT Makina Lite receiver,

• External power supply 100 - 240V AC / 12V DC, 2A,

• Rubber feets for desktop installation (4 pieces) and
• Manual.

Additional accessories may be purchased separately, including:

• CAT-5 Ethernet cable for WAN interface,

• CAT-5 Ethernet cable for LAN interface,
• USB C cable for USB interface,

• DB9 terminated RS-232 null-modem serial cable and

• 512 IP supervised alarm accounts license.

2.4 Models
• IIT Makina Lite 8 MB RAM and,
• IIT Makina Lite 16 MB RAM.

7
 3 INSTALLATION

3 Installation
3.1 Connectors and LEDs
No. CON / LED State Description
1 WAN Network interface for receiving alarm messages from Internet. Other
services may run on this interface depending on settings.
2 LAN Network interface for WEB interface. Other services may run on this
interface depending on settings.
3 PWR On Device is powered from external power supply.
Off Device is turned off. No power from external power supply.
4 CSE On Central Station Equipment connected to alarm messages distributor.
Off Central Station Equipment not connected to alarm messages distribu-
tor.
5 ALM On Alarm messages interface is active.
Off Alarm messages interface is not active.
6 MSG On Alarm messages interface is receiving message.
Off Alarm messages interface is waiting for next message.
7 DC External power supply connector: 12 V DC, 2A, + inside, - outside.
8 RS232 Serial port for connecting to Central Station Equipment.
9 SD Micro SD card slot.
10 USB USB Type C port for connecting to a Central Station Equipment.

Figure 3: IIT Makina Lite front and back panels

3.1.1 Network Interfaces

The device has two network interfaces: WAN and LAN. The WAN interface is used to receive alarm
messages from the Internet, while the LAN interface is used for accessing the device’s web interface and
other services. Both interfaces can be configured to use DHCP or static IP addresses.
Left LED on each interface indicates the network connection and speed (orange for 10 Mbps, green
for 100 Mbps, off for no connection).
Right LED indicates network activity (flashing when data is being transmitted).

3.1.2 SD Card

When no SD card is detected, the device will not boot and will indicate missing or damaged SD card by
flashing CSE, ALM and MSG LEDs. The SD card is used to store accounts and receoved alarm messages.
It is recommended to use a high-quality SD card with a minimum capacity of 16 GB. The SD card should
be formatted in FAT32 file system. The device will automatically create a directory structure on the SD
card when it is first used.

8
3 INSTALLATION 3.2 Connecting the receiver

3.2 Connecting the receiver

When first time the device is powered on, WAN interface will try to obtain IP address via DHCP. If
it fails, it will use default IP address: 192.168.8.199. The LAN interface will use default IP address:
192.168.8.198.
The device can be accessed via web interface using a web browser by entering the IP address of the
LAN interface. The default username is "admin" and the default password is "admin".
As alarm receiver has two network interfaces, one USB Type C port and one RS232 port, it can
be connected to Central Station Equipment in several ways. Here will be described two most common
connection schemes.

3.2.1 Secure connection scheme

Figure 4: Secure connection scheme

In this scheme, the receiver is connected to the Central Station Equipment via RS232 port. The WAN
interface is connected to the Internet via dedicated router and secured using NAT and firewall filtering.
The LAN interface is connected to a local network and used for local web interface, sending mail messages,
synchronizing receiver date and time via network time server and domain name resolution.
This setup allows for secure communication between the receiver and the Central Station Equipment,
as well as access to the device’s web interface from the local network.

• For Central Station Equipment that supports RS323 connection, this is the recommended connec-
tion scheme.

• For Central Station Equipment that does not support RS232 connection, the USB Type C port can
be used instead.

• For traffic intensive applications, it is recommended to use LAN interface for Central Station Equip-
ment connection, while WAN interface is used for receiving alarm messages from the Internet.

Both RS232 and USB Type C works as a serial port, so the same settings can be used for both
connections with data rate from 9600 to 115200 bps, 8 data bits, no parity, 1 stop bit and no flow control.

9
3.2 Connecting the receiver 3 INSTALLATION

3.2.2 Connection scheme for maximum number of accounts

Figure 5: Connection scheme for maximum number of accounts

Second connection scheme is used when the maximum number of accounts is required. In this case, the
receiver is connected to the Central Station Equipment via RS232, USB Type C port or LAN interface.
The WAN and LAN interfaces are both connected to the Internet via office router with NAT Load
Balancing. To receive alarm messages using single port on office router with NAT Load Balancing,
please refer to your router documentation for instructions on how to configure it. This setup allows
for maximum number of accounts to be used and intensive traffic, as the receiver can handle efficiently
multiple connections from different alarm panels.

• For Central Station Equipment that supports RS323 connection, this is the recommended connec-
tion scheme.
• For Central Station Equipment that does not support RS232 connection, the USB Type C port can
be used instead.

• For traffic intensive applications, it is recommended to use LAN interface for Central Station Equip-
ment connection, while WAN interface is used for receiving alarm messages from the Internet.

Both RS232 and USB Type C works as a serial port, so the same settings can be used for both
connections with data rate from 9600 to 115200 bps, 8 data bits, no parity, 1 stop bit and no flow control.

10
4 DASHBOARD

4 Dashboard
The web interface is accessible via the LAN interface IP address. The web interface allows you to see
current status, configure the device, manage accounts, and view received alarm messages.
When you access the web interface for the first time, you will be prompted to enter the username and
password. The default username is "admin" and the default password is "admin". It is recommended to
change the password after the first login for security reasons.

Figure 6: WEB interface login page

After successful login, you will be redirected to the dashboard page, where you can see the current
status of the device, including the number of accounts, received messages, and other information.

Figure 7: WEB interface dashboard page

The dashboard page contains the following panels:

• System - shows the system information, including the device name, firmware version, and uptime.

• Interface - shows number of messages and bytes received per minute with last half hour totals.

• Distributor - shows number of messages and bytes sent per minute with last half hour totals.

• Analyzer - shows the accounts statistical data.

11
4.1 System panel 4 DASHBOARD

4.1 System panel

The system panel shows the following status buttons:
• WAN - shows the status of the WAN interface. If the WAN interface is connected and has an IP
address, the button will be green, otherwise it will be red.
• LAN - shows the status of the LAN interface. If the LAN interface is connected and has an IP
address, the button will be green, otherwise it will be red.
• CSE - shows the status of the Central Station Equipment connection. If the connection is estab-
lished, the button will be green, otherwise it will be red.
• Time - shows the status of the time synchronization. If the time is synchronized, the button will
be green, otherwise it will be red.
• Mail - shows the status of the mail server connection. If the connection is established, the button
will be green, otherwise it will be red.
• Temp - shows the status of the temperature sensor. If the temperature sensor is working, the
button will be green, otherwise it will be red.

Other information displayed in the system panel includes:

• Hostname - the name of the device, which can be changed in the settings.
• System time - current device system time and date.

• Uptime - the time since the device was last restarted.

• Version - the version of the firmware currently installed on the device.
• License - shows number of licensed accounts.
• Receiver ID - The receiver ID, which can be changed in the settings.

• IP address - the current IP address of the WAN and LAN interfaces.

• Gateway - the gateway address of the WAN and LAN interfaces.
• TEMP - the current temperature measured by the temperature sensor.

• RAM - the current memory usage percentage.

• DISK - the current disk usage percentage.

4.2 Interface panel

The interface panel shows the number of messages and bytes received per minute with last half hour
totals for both WAN and LAN interfaces. Graph shows the number of messages and bytes received per
minute for the last 30 minutes.

4.3 Distributor panel

The distributor panel shows the number of messages and bytes sent per minute with last half hour totals.
Graph shows the number of messages and bytes sent per minute for the last 30 minutes.

4.4 Analyzer panel

The analyzer panel shows the number of active, online and offline accounts including percentages.

12
5 SETTINGS

5 Settings
To enter the settings, click on the "Settings" button in the top menu. The settings are divided into
several sections, which are described below. All setting changes can be saved by clicking on the "Save"
button at the top of the page.

5.1 General settings

Figure 8: General settings page

The general settings section allows you to configure:

• Hostname - the name of the device, which is used to identify the device on the network.

• Receiver code - a unique identifier for the receiver, which can be used to identify the receiver in
alarm messages.

• Interface code - a unique identifier for the interface, which can be used to identify the line card
interface in alarm messages.

• NTP server - the address of the NTP server used for time synchronization.

• Timezone - the timezone where device resides used for local time synchronization.

• WEB Interface - the interface on which WEB page will be visible: All, LAN or WAN.

• Port - the port of the web interface.

• Items per page - the number of items per page when viewing accounts and alarm messages.

• Dashboard refresh period - number od seconds between dashboard data refresh.

13
5.2 WAN (ETH0) settings 5 SETTINGS

5.2 WAN (ETH0) settings

Figure 9: WAN interface settings page

• Use DHCP - enables or disables DHCP Client.

• IP address - manually asigned interface IP address when DHCP Client is disabled.
• Subnet mask - manually asigned interface subnet mask when DHCP Client is disabled.
• Gateway - manually asigned interface gateway IP address when DHCP Client is disabled.
• DNS server - manually asigned interface DNS server IP address .

If IP address is not defined or DHCP Server is not accessibe, default IP address 192.168.8.199 is
automatically assigned to WAN interface.

5.3 LAN (ETH1) settings

Figure 10: LAN interface settings page

• Use DHCP - enables or disables DHCP Client.

• Default Interface - enables or disables LAN (ETH1) as default network interface.
• IP address - manually asigned interface IP address when DHCP Client is disabled.
• Subnet mask - manually asigned interface subnet mask when DHCP Client is disabled.
• Gateway - manually asigned interface gateway IP address when DHCP Client is disabled.
• DNS server - manually asigned interface DNS server IP address .

14
5 SETTINGS 5.4 Distributor settings

If IP address is not defined or DHCP Server is not accessibe, default IP address 192.168.8.198 is
automatically assigned to WAN interface.
All outgoing network connections are made through the default network interface, such as: sending
notifications, time synchronization, firmware upgrade, cloud backup and Internet connection verification.
If LAN (ETH1) is not set as default, then WAN (ETH0) is default interface automatically.

5.4 Distributor settings

Figure 11: Distributor settings page

5.4.1 Distributor
• Type - type of distributor:
SIA Network - sends messages to CSE using DC-07-2001.04 protocol via TCP/IP
SIA USB - sends messages to CSE using DC-07-2001.04 protocol via USB port
SIA Serial - sends messages to CSE using DC-07-2001.04 protocol via RS-232 port
SGC Network - sends messages to CSE using SG compatible protocol via TCP/IP
SGC USB - sends messages to CSE using SG compatible protocol via USB port
SGC Serial - sends messages to CSE using SG compatible protocol via RS-232 port

• Heartbeat - number of seconds between two heartbeat messages to CSE.

• Send retries - number of send retries when ACK was not received within replay timeout.

• Replay timeout - number of seconds to wait for ACK after message was sent.

5.4.2 Distribution options

• Baudrate - RS-232 or USB serial port speed when serial or USB distributor type is in use.

• Port - TCP/IP port when Network distributor type is in use.

• Add time to message - when enabled, message time will be added to distributed message.

• Distribute SIA extended data - when disabled extended data will be removed from distributed
message.

• Remove leading zeros from account - when enabled leading zeros will be removed from account
number to fit 4, 6, 8 or 16 account code length.

• Add leading zeros to account - when enabled leading zeros will be added to account number to
fit 4, 6, 8 or 16 account code length.

15
5.5 Interface 5 SETTINGS

5.4.3 Contact ID format codes

• Communication trouble and restore - supervised alarm panel communication trouble and
restore code.

• IP address update - code sent to CSE on supervised alarm panel IP address update.

• MAC address update - code sent to CSE on supervised alarm panel MAC address update.

• IMEI address update - code sent to CSE on supervised alarm panel IMEI address update.

5.4.4 SIA DCS format codes

• Communication trouble - supervised alarm panel communication trouble code.

• Communication restore - supervised alarm panel communication restore code.

• IP address update - code sent to CSE on supervised alarm panel IP address update.

• MAC address update - code sent to CSE on supervised alarm panel MAC address update.

• IMEI address update - code sent to CSE on supervised alarm panel IMEI address update.

5.5 Interface

Figure 12: Interface settings page

• Interface - network interface for receiving alarm messages (WAN, LAN or both).

• Port - for receiving alarm messages on selected network interface.

• Encryption key - universal encryption key for decryption of encrypted alarm messages.

• Socket close wait timeout - for client (alarm message sender) to close communication socket
before receiver closes socket by force.

• Ignore bad timestamp - in alarm messages and parse messages as timestamp is accurate.

• Mask no data received - doesn’t sends no data received to distributor when the client did not
send an alarm message within the close wait timeout.

• Mask bad data - doesn’t sends bad data received to distributor when a client sends an incorrect
alarm message.

• Mask repeated messages - doesn’t sends repeated message to distributor when client resends
same message.

16
5 SETTINGS 5.6 Accounts

5.6 Accounts

Figure 13: Accounts settings page

5.6.1 New account default values

• Caption - default new account caption.

• CID test codes - Contact ID test codes that may be received from an account, separated by
comma.

• SIA test codes - SIA DCS test codes that may be received from an account, separated by comma.

• Encryption key - default alarm panel encryption key for decryption of encrypted alarm messages.

• Test message timeout - time between two alarm panel test messages in seconds. If test message
is not received within timeout an communication error alarm message is generated.

• Test message pass through - time between two test messages forwarded to the distributor (all
test messages in between are masked).

• Mask test - if enabled alarm messages containing test codes are masked. Not sent to CSE.

• Mask IP Update - if enabled account IP address updates are masked. Not sent to CSE.

• Mask MAC Update - if enabled account MAC address updates are masked. Not sent to CSE.

• Mask IMEI Update - if enabled account IMEI address updates are masked. Not sent to CSE.

• Mask SIA extended - if enabled SIA extended data is masked. Not sent to CSE.

5.7 Watchdog

Figure 14: Watchdog settings page

17
5.8 Debug 5 SETTINGS

5.7.1 On-line accounts test

• Between tasks period - is timeout between on-line accounts test in minutes.
• First task timeout - first test delay in minutes after device restart or first boot. Gives time to
all accounts to send at least one test message.

5.7.2 Database purge

• Between tasks period - is timeout between database purges.

Purge task is releasing from RAM all deleted alarm messages. Alarm messages sent to CSE via
distributor older than 12 hours are automatically deleted. If 80% or RAM is used, alarm messages
younger than 12 hours may also be deleted. Old statistical data related to IP address changes, test
events, double alarm message, bad messages, interface and distributor load is also deleted from RAM.

5.7.3 Internet connection test

• Between tasks period - is timeout between Internet connection tests.
• FQDN - fully qualified domain name for testing Internet conectivity.

When testing Internet connection, first DNS server is verified by converting fully qualified domain
name to IP address. After that simple ping is performed over IP address.
When entering an Internet server address in FQDN field, please be sure that responds to ping.

5.8 Debug

Figure 15: Debug settings page

5.8.1 Syslog
• Server - IP address of syslog server.
• Port - syslog server port for sending log messages.

IIT Makina Lite receiver is using standard ”IETF-syslog format” to transfer all log messages to syslog
server via UDP protocol.

5.8.2 Loglevel
Each IIT Makina Lite receiver task and system services, has its own log level. Every upper log level
includes all previous levels.

• Info - standard informational messages.

• Errors - all info and error messages.
• Warnings - all info, error and warning messages.
• Verbose - all info, error, warning and verbose messages.

• Watchdog - task log level.

18
5 SETTINGS 5.9 Users

• Interface - task log level.

• Distributor - task log level.

• System - log level for all system services.

• Memory - enables or disables memory allocation problems logging.

System libraries are used by two or more tasks at the same time and covers: database, time synchro-
nisation, backup, restore, export, import and web application.

5.9 Users

Figure 16: Users settings page

IIT Makina Lite receiver has two fixed users:

• Administrator - has rights to change settings, execute tools and edit accounts.

• User - has rights to view settings, accounts data and received alarm messages.

Default administrator username and password is: admin. Default user username and password is:
user. Once forgotten administrator username and password can be changed only by mean of deleting
preferences table from SD card manually.
Preferences table path and filename is: /var/db/pref erences.db

5.10 Notifications

Figure 17: Notifications settings page

19
5.10 Notifications 5 SETTINGS

5.10.1 Mail server

• Server - mail server fully qualified domain name or IP address.
• Port - mail server port number.
• Username - for mail server authentication (only if server requires).

• Password - for mail server authentication (only if server requires).

• Use SSL - if enabled mail server port number shall also be changed to coresponding SSL port
number 465.
• Timeout - period of time in miliseconds that client will wait form mail server to receive outgoing
e-mail message.

5.10.2 Mail content

• Recipients - list of recipients mail addresses seprated by: ;.
• Sender - mail sender address.
• Subject - for notification messages sent by IIT Makina Lite receiver.

• Body template - notification message template.

20
6 ACCOUNTS

6 Accounts
Accounts page of IIT Makina Lite alarm receiver shows a list of accounts in browsable list. Accounts are
sorted by account code in ascending order.

Figure 18: Accounts

6.1 Columns
• Caption - account caption (may be synchronized with DC Discovery Central Station Software).

• Code - account code.

• Installer - account installer (may be synchronized with DC Discovery Central Station Software).

• Proto - alarm messages protocol.

• Fmt - alarm messages format.

• Enc - Yes if alarm messages are encrypted.

• Test - test message codes separated by: ,.

• Wait [s] -test message timeout in seconds.

• Avg [s] - average period of time between to test messages.

• Mask - list of masked alarm messages codes separated by ,.

• IP Address - current account IP address. In case of communication error, this information may
be incorrect.

• Last Message - last received message time.

• Supervised - Yes if account is supervised (maximal number of supervised accounts depends on

license).

• On Line - Yes if account is on-line.

• Active - Yes if account is active.

• Created - date and time when account record was created.

6.2 Commands
• Edit - opens selected account editor. If multiple accounts are selected, editor is opened for first
selected account.

• Delete - deletes all selected accounts.

• Filter - Opens accounts list filter dialog.

• Refresh - refreshes list of accounts with current filter.

21
6.3 Editor 6 ACCOUNTS

6.3 Editor

Figure 19: Account editor

6.3.1 Editable fields

• Caption - account caption (if accounts are synchronized with DC Discovery Central Station Soft-
ware, then this field is not editable).

• Installer - account installer (if accounts are synchronized with DC Discovery Central Station
Software, then this field is not editable).

• Encryption key - account alarm messages encryption key. Leave blank if accout doesn’t sends
encrypted messages or default encryption key is used.

• Mask codes - alarm messages codes separated by ,. All messages received with this codes will be
masked and not sent to CSE via distributor.

• Test codes - test message codes separated by: ,.

• Timeout - test message timeout in seconds.

• Mask test - mask test messages defined with test codes.

• Pass through - period between two not masked test messages in hours (not masked messages will
be sent to CSE via distributor).

• Mask IP Update - if enabled account IP address updates are masked. Not sent to CSE.

• Mask MAC Update - if enabled account MAC address updates are masked. Not sent to CSE.

• Mask IMEI Update - if enabled account IMEI address updates are masked. Not sent to CSE.

• Mask SIA extended - if enabled SIA extended data is masked. Not sent to CSE.

• Supervised - if enabled, account is supervised. On connection timeout, communication trouble

message is generated and sent to CSE.

• Active - if disabled, all messages received from or generated for this account are masked and not
sent to CSE.

22
6 ACCOUNTS 6.4 Filter

6.3.2 Non editable fields

• Code - account code.

• On-line - 1 or Yes for account which sends test messages within given timeout.

• Proto - protocol that alarm panel or communication module are using to transfer alarm messages.

• Fmt - alarm messages format in use.

• Enc - if enabled account is sending encrypted alarm messages.

• Test period - average period of time between two test messages in seconds.

• IP update period - average period of time between two IP update alarm messages in minutes.

• Double message period - average period of time between two double alarm messages in minutes.

• IP - current account IP address. In case of communication error, this information may be incorrect.

• MAC - current account MAC address.

• IMEI - current account IMEI address.

• Last message - last received message time.

• Test time - last received test message time.

• Event code - last received test message event code.

• Added - date and time when message is appended to database.

• Modified - date and time when message is modified.

6.4 Filter

Figure 20: Account filter

Using account filter user may filter displayed account list by:

• Caption - account caption.

• Code - account code.

• IP address - account IP address.

• Installer - account installer caption.

• Supervised - when ’On’ shows only supervised, when ’Off’ shows only non-supervised and with
’All’ shows all accounts.

• Comm. status - ’Off line’ shows account with communication trouble, ’On line’ shows accounts
without communication trouble and ’All’ shows all accounts.

23
6.4 Filter 6 ACCOUNTS

• Active status - ’Inactive’ show inactive accouns, ’Active’ shows active accounts and ’All’ shows
all accounts.

Any combination of account filters is allowed.

For caption, code, IP address and installer ’contains’ filter is used. If in ’Code’ filter field is entered
’23’ then all accounts with code that contains text: ’23’ are displayed.

24
7 MESSAGES

7 Messages
Accounts page of IIT Makina Lite alarm receiver shows a list of accounts in browsable list. Accounts are
sorted by account code in ascending order.

Figure 21: Messages

7.1 Columns
• Received - date and time when alarm message is received.
• Acc - alarm message account code.
• Caption - alarm message account caption (receiver messages doesn’t have caption).
• Description - alarm message description as defined by standard format messages.
• IP Address - ip address of the source of the alarm message (receiver messages doesn’t have IP
address).
• Prt - alarm message protocol (receiver messages doesn’t have protocol).
• Fmt - alarm message format (receiver messages doesn’t have format).
• R - receiver code.
• I - interface code.
• Evt - alarmm message event code (receiver messages doesn’t have event code).
• Grp - alarm message group code (receiver messages doesn’t have group code).
• Par - alarm message parameter code (receiver messages doesn’t have parameter code).

Event code describes type of alarm message as defined in format. Example type: Alarm parition
disarming by user code. Group code is numerical ID of alarm sensors group or partition or part of
building, . . . Parameter code is numerical ID of expansion module, sensor, user, ...

7.2 Commands
• View - opens selected alarm message details view. If multiple messages are selected, view is opened
for first selected message.
• Delete - deletes all selected alarm messages.
• Filter - Opens alarm messages list filter dialog.
• Refresh - refreshes list of alarm messages with current filter.

25
7.3 View 7 MESSAGES

7.3 View

Figure 22: Message view

7.3.1 View fields

• Received - date and time of receipt of the alarm message.

• Account - account code of the alarm control panel that sent the message.

• Description - alarm message description according to standard format.

• Qualifier - alarm message qualifier code.

• Event - alarm message event code.

• Group - alarm message group code.

• Parameter - alarm message parameter code.

• Sia Extended - alarm message extended data (if message format belongs to SIA family).

• Client - IP address and port of the alarm control panel that sent the message.

• Listener - IP address and port of the alarm receiver to which the alarm message was received.

• Receiver - receiver code.

• Interface - receiver interface code.

• Protocol - alarm message protocol code.

• Format - alarm message format code.

• Message ID - internal alarm message ID.

• Message - received alarm message content before parsing.

26
7 MESSAGES 7.4 Messages filter

7.4 Messages filter

Figure 23: Messages filter

Using messages filter user may filter displayed alarm messages list by:

• Caption - account caption.

• Account - account code.

• Description - alarm message description bfro standard message format.

• IP address - account IP address.

Any combination of alarm message filters is allowed.

For caption, account, description and IP address ’contains’ filter is used. If in ’Account’ filter field is
entered ’23’ then all alarm messages for accounts with code that contains: ’23’ are displayed.

27
 8 TOOLS

8 Tools
To open the tools, click on the "Tools" button in the top menu. The tools are divided into several
sections, which are described below.

8.1 Export

Figure 24: Export tool

Export tool saves all filtered accounts into ’CSV’ file.

8.1.1 Filter
Using export filter user may filter exported accounts list by:

• Caption - account caption.

• Installer - account installer caption.

• Code - account code.

• Supervised - when ’On’ exports only supervised, when ’Off’ exports only non-supervised and with
’All’ exports all accounts.

• Comm. status - ’Off line’ exports account with communication trouble, ’On line’ exports accounts
without communication trouble and ’All’ exports all accounts.

• Active status - ’Inactive’ exports inactive accouns, ’Active’ exports active accounts and ’All’
exports all accounts.

8.1.2 CSV file

Exported ’CSV’ file fields are:

• ID - account record ID.

• CAPTION - account caption.

• INSTALLER - account installer.

• CODE - account code.

• PROTOCOL - alarm messages transport protocol.

• FORMAT - alarm messages format.

• ENCRYPTIONKEY - alarm messages private encryption key.

• IPADDRESS - alarm control panel ’IP’ address.

• MACADDRESS - alarm control panel ’MAC’ address.

28
8 TOOLS 8.2 Import

• IMEIADDRESS - alarm control panel ’IMEI’ address.

• MASKEVENT - list of event codes separated by ’,’ for masking (hiding) messages.
• TESTEVENT - list of test event codes separated by ’,’.
• TESTEVENTIMEOUT - time in seconds between two consecutive test messages.
• TESTEVENTRANSIENTPERIOD - time in hours between two pass through test messages.
• MASKTESTEVENT - masks all test messages except pass through (1 = ’Yes’ and 0 = ’No’).
• MASKIPUPDATE - masks IP update messages (1 = ’Yes’ and 0 = ’No’).
• MASKMACUPDATE - masks IP update messages (1 = ’Yes’ and 0 = ’No’).
• MASKIMEIUPDATE - masks IP update messages (1 = ’Yes’ and 0 = ’No’).
• SUPERVISED - account is supervised if value is 1 (first 512 accounts with ’SUPERVISED’ set
to 1 are supervised).
• ONLINE - account is online if value is 1.
• ACTIVE - account is active if value is 1.

To export accounts, click on ’Export’ button and ’export.csv’ file will be downloaded.

8.2 Import

Figure 25: Import tool

Accounts can be inserted or updated only from CSV file. First row contains list of column names. If
’ID’ column is missing then ’CODE’ column will be used to detect if record shall be inserted or updated.
Minimal set of columns must include one of following: ’ID’ or ’CODE’ together with any other column.

• ID - account record ID.

• CAPTION - account caption.
• INSTALLER - account installer.
• CODE - account code.
• PROTOCOL - alarm messages transport protocol.

29
8.3 Backup 8 TOOLS

• FORMAT - alarm messages format.

• ENCRYPTIONKEY - alarm messages private encryption key.
• IPADDRESS - alarm control panel ’IP’ address.
• MACADDRESS - alarm control panel ’MAC’ address.
• IMEIADDRESS - alarm control panel ’IMEI’ address.
• MASKEVENT - list of event codes separated by ’,’ for masking (hiding) messages.
• TESTEVENT - list of test event codes separated by ’,’.
• TESTEVENTIMEOUT - time in seconds between two consecutive test messages.
• TESTEVENTRANSIENTPERIOD - time in hours between two pass through test messages.
• MASKTESTEVENT - masks all test messages except pass through (1 = ’Yes’ and 0 = ’No’).
• MASKIPUPDATE - masks IP update messages (1 = ’Yes’ and 0 = ’No’).
• MASKMACUPDATE - masks IP update messages (1 = ’Yes’ and 0 = ’No’).
• MASKIMEIUPDATE - masks IP update messages (1 = ’Yes’ and 0 = ’No’).
• SUPERVISED - account is supervised if value is 1 (first 512 accounts with ’SUPERVISED’ set
to 1 are supervised).
• ONLINE - account is online if value is 1.
• ACTIVE - account is active if value is 1.
When import file is ready, select it by using ’Browse’ button and then click on ’Import’.

8.2.1 Transport protocols

• SIA - SIA DC-09 protocol
• E2 - Enigma IP2 protocol
• CSV - Comma Separated Values protocol
• M2M - Machime to machime protocol
• SCID - Simple Contact ID protocol

8.2.2 Formats
• DCS - SIA formats (DC-03-2017 and DC-04-2000.05)
• CID - Ademco Contact ID format (DC-05-2016-DCS)
• NULL - ’NULL’ test message format (SIA DC-09)

8.3 Backup

Figure 26: Backup tool

30
8 TOOLS 8.4 Restore

Database backup may save all records from accounts, alarm messages and parameters tables into ’TAR’
file depending on user selection. By clicking on ’Backup’ button, ’backup.tar’ file will be generated and
downloaded.
TAR file is standard non-compressed archive file.

8.4 Restore

Restore process will replace content in all restored tables from selected backup file upon user selection.
Throughout this process MAKINA LITE alarm receiver will be restarted once.

Figure 27: Restore tool

To restore database after selecting tables to restore, select backup ’TAR’ file by using ’Browse’ button
and then click on ’Restore’.
If selected backup ’TAR’ file doesn’t contain all tables then only tables from backup file may be
restored, regardless of which tables are selected for restore.
For example, if backup file doesn’t contains accounts table and user has selected accounts table for
restore, account will not be restore.
Restore process will delete all existing data in selected tables.

8.5 Defaults

Warning. During this process:

• All account records will be removed together with alarm messages and statistical data.

• All settings will be reset to default values including network settings and user accounts.

• Throughout this process MAKINA LITE alarm receiver will be restarted once.

31
8.6 Upgrade 8 TOOLS

Figure 28: Defaults tool

To reset receiver to default settings, please answer ’Yes’ to ’Do you really want to reset MAKINA
LITE alarm receiver to default values?’ and click on ’Reset’ button.

8.6 Upgrade

Figure 29: Upgrade tool

IIT Makina Like alarm receiver upgrade files may be found at:
https://www.iit.com.hr/iitmakinalite/downloads .
Select downloaded upgrade ’TAR’, firmware or web ’BIN’ file and click on Upgrade. Do not turn off
power while upgrading MAKINA LITE alarm receiver.
Power failure while upgrading, may brick your alarm receiver. Before starting the upgrade process,
make sure that the receiver power supply is connected to an uninterruptible power supply.
Upgrade file name format is: iitmakinalite-<target>-<model>-<yyyymmdd>.<type> where:

8.6.1 Targets
• upd - integrated ’TAR’ upgrade file.

• fw - firmware binary upgrade file.

• web - web application binary upgrade file.

8.6.2 Models
• N8R8 - 8 MB Flash Quad SPI with 8MB RAM Octal SPI.

• N16R8 - 16 MB Flash Quad SPI with 8MB RAM Octal SPI.

• N16R16 - 16 MB Flash Quad SPI with 16MB RAM Octal SPI.

32
8 TOOLS 8.7 Restart

8.6.3 Models
• tar - integrated ’TAR’ upgrade file with firmware and web application binary upgrade files.
• bin - binary upgrade file.

8.6.4 Example
iitmakinalite-upd-N16R8-20250514.tar is integrated ’TAR’ upgrade file with firmware and web ap-
plication binary upgrade files for receiver model with 16 MB internal flash disk and 8 MB RAM issued
on 15. May, 2025.

8.7 Restart

Figure 30: Restart tool

To restart receiver, answer with ’Yes’ on ’Do you really want to restart MAKINA LITE alarm receiver?’
question and click on ’Restart’ button.

Figure 31: Reload after restart

Wait for couple of minutes and click on ’Reload’ button.

33
LIST OF FIGURES LIST OF FIGURES

List of Figures
1 IIT Makina Lite front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2 IIT Makina Lite back panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3 IIT Makina Lite front and back panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4 Secure connection scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5 Connection scheme for maximum number of accounts . . . . . . . . . . . . . . . . . . . . 10
6 WEB interface login page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
7 WEB interface dashboard page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
8 General settings page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
9 WAN interface settings page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
10 LAN interface settings page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
11 Distributor settings page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
12 Interface settings page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
13 Accounts settings page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
14 Watchdog settings page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
15 Debug settings page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
16 Users settings page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
17 Notifications settings page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
18 Accounts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
19 Account editor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
20 Account filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
21 Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
22 Message view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
23 Messages filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
24 Export tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
25 Import tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
26 Backup tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
27 Restore tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
28 Defaults tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
29 Upgrade tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
30 Restart tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
31 Reload after restart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

34